DL4001 THRU DL4007 SURFACE MOUNT RECTIFIERS REVERSE VOLTAGE: 50 - 1000 V CURRENT: 1.0 A FEATURES DO - 213AB ◇ Glass passivated device ◇ Ideal for surface mouted applications ◇ Low leakage current ◇ Metallurgically bonded construction SOLDERABLE ENDS 0 D2=D1 ＋ －0.20 D1 2.6± 0.15 MECHANICAL DATA D2 ◇ Case:JEDEC DO-213AB,molded plastic over passivated chip ◇ Terminals:Solder Plated, solderable per MIL-STD-750, Method 2026 ◇ Polarity: Color band denotes cathode end ◇ Weight: 0.0046 ounces, 0.116 gram ◇ Mounting position: Any 0.5± 0.1 0.5± 0.1 4.9± 0.2 Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase,half wave,60Hz,resistive or inductive load.For capactive load,derate current by 20%. MDD Catalog Number Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forword rectified current T A=75℃ VRRM VRMS VDC DL DL DL 4001 4002 4003 DL 4004 DL 4005 DL 4006 50 100 200 400 600 800 1000 35 70 140 280 420 560 700 50 100 200 400 600 800 1000 DL UNITS 4007 V V V I(AV) 1.0 A IFSM 30 A VF 1.1 V Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load (JEDEC method) Maximum forward voltage at 1.0A Maximum DC reverse current @TA=25℃ at rated DC blockjing voltage @T A=125℃ Typical junction capacitance (NOTE 1) Typical thermal resistance (NOTE 2) Typical thermal resistance (NOTE 3) Operating temperature range Storage temperature range 5.0 IR Cj RjθL RjθA Tj TSTG 50 15 20 50 - 55 --- + 175 - 55 --- + 175 NOTES:1. Measured at 1.0MHz and applied average voltage of 4.0V DC. 2. Thermal resistance junction to lead, 6.0 mm 2 coppeer pads to each terminal. 3. Thermal resistance junction to ambient, 6.0 mm 2 coppeer pads to each terminal. MDD ELECTRONIC μA pF ℃/W ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES DL4001 THRU DL4007 1.0 .8 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 0 0 25 50 75 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 100 125 150 175 AMBIENT TEMPERATURE, ( ) 50 40 30 20 10 0 1 INSTANTANEOUS REVERSE CURRENT, (uA) T J = 25 .1 Pulse Width = 300us 1% Duty Cycle 1.0 1.2 1.4 1.6 60 80 100 .4 .1 .04 TJ = 25 .01 0 20 100 60 40 20 TJ = 25 2 1 .2 .4 40 TJ = 100 1.0 200 .1 20 10 FIG. 5 - TYPICAL JUNCTION CAPACITANCE 10 6 4 6 8 10 1.0 2 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD VOLTAGE, (V) JUNCTION CAPACITANCE, (pF) INSTANTANEOUS FORWARD CURRENT, (A) 1.0 .8 4 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 .6 2 NUMBER OF CYCLES AT 60Hz FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS .01 .4 8.3ms Single Half Sine-Wave (JEDED Method) 4 10 20 40 100 REVERSE VOLTAGE, ( V ) MDD ELECTRONIC