EXAR CPLL

XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
October 2012
Rev. 1.0.1
GENERAL DESCRIPTION
APPLICATIONS
The XRP7724 is a quad channel Digital Pulse
Width Modulated (DPWM) Step down (buck)
controller. A wide 4.75V to 5.5V and 5.5V to
25V input voltage dual range allows for single
supply operation from standard power rails.
With integrated FET gate drivers, two LDOs for
standby power and a 105kHz to 1.23MHz
independent channel to channel programmable
constant operating frequency, the XRP7724
reduces overall component count and solution
footprint and optimizes conversion efficiencies.
A selectable digital Pulse Frequency Mode
(DPFM) capable of better than 80% efficiency
at light current load and low operating current
allow for portable and Energy Star compliant
applications. Each XRP7724 output channel is
individually programmable as low as 0.6V with
a resolution as fine as 2.5mV, and
configurable for precise soft start and soft stop
sequencing, including delay and ramp control.
The XRP7724 operations are fully controlled
via a SMBus-compliant I2C interface allowing
for
advanced
local
and/or
remote
reconfiguration, full performance monitoring
and reporting as well as fault handling.
Built-in independent output over voltage, over
temperature, over-current and under voltage
lockout protections insure safe operation
under abnormal operating conditions.
The XRP7724 is offered in a RoHS compliant,
“green”/halogen free 44-pin TQFN package.







Servers
Base Stations
Switches/Routers
Broadcast Equipment
Industrial Control Systems
Automatic Test Equipment
Video Surveillance Systems
FEATURES
 Quad Channel Step-down Controller
 Digital PWM 105kHz-1.23MHz Operations
 Individual Channel Frequency Selection
 Patented digital PFM with Ultrasonic mode
 Patented Over Sampling Feedback
 Integrated MOSFET Drivers
 Programmable 5 coefficient PID control
 4.75V to 25V Input Voltage
 4.75V-5.5 and 5.5V-25V Input Ranges
 0.6V to 5.5V Output voltage
 SMBus Compliant - I2C Interface
 Full Power Monitoring and Reporting
 3 x 15V Capable PSIO + 2 x GPIOs
 Full Start/Stop Sequencing Support
 Built-in Thermal, Over-Current, UVLO
and Output Over-Voltage Protections
 On Board 5V and 3.3V Standby LDOs
 On Board Non-volatile Memory
 Supported by PowerArchitect™
TYPICAL APPLICATION DIAGRAM
Fig. 1: XRP7724 Application Diagram
Exar Corporation
48720 Kato Road, Fremont CA 94538, USA
www.exar.com
Tel. +1 510 668-7000 – Fax. +1 510 668-7001
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
ABSOLUTE MAXIMUM RATINGS
OPERATING RATINGS
These are stress ratings only and functional operation of
the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect
reliability.
Input Voltage Range VCC ............................... 5.5V to 25V
Input Voltage Range VCC = LDO5 ................ 4.75V to 5.5V
VOUT1, 2, 3, 4 ...................................................... 5.5V
Junction Temperature Range ....................-40°C to 125°C
JEDEC Thermal Resistance θ JA ..........................30.2°C/W
VCCD, LDO5, LDO3_3, GLx, VOUTx ............. -0.3V to 7.0V
ENABLE, 5V_EXT ....................................... -0.3V to 7.0V
GPIO0/1, SCL, SDA................................................ 6.0V
PSIOs Inputs, BFB .................................................. 18V
DVDD, AVDD ........................................................ 2.0V
VCC ...................................................................... 28V
LX# ............................................................. -1V to 28V
BSTx, GHx .................................................... VLXx + 6V
Storage Temperature .............................. -65°C to 150°C
Power Dissipation ................................ Internally Limited
Lead Temperature (Soldering, 10 sec).................... 300°C
ESD Rating (HBM - Human Body Model) .................... 2kV
ELECTRICAL SPECIFICATIONS
Specifications with standard type are for an Operating Junction Temperature of T J = 25°C only; limits applying over the full
Operating Junction Temperature range are denoted by a “•”. Minimum and Maximum limits are guaranteed through test,
design, or statistical correlation. Typical values represent the most likely parametric norm at T J = 25°C, and are provided for
reference purposes only. Unless otherwise indicated, V CC = 5.5V to 25V, 5V EXT open. Note that in cases where there is a
discrepancy in values shown in this section and other sections of the datasheet, the values in the Electrical Specification
section shall be deemed correct and supersede the other values.
QUIESCENT CURRENT
Parameter
Min.
VCC Supply Current in SHUTDOWN
ENABLE Turn On Threshold
ENABLE Pin Leakage Current
Typ.
Max.
Units
10
20
µA
0.95
V
10
uA
0.82
Conditions
EN = 0V, VCC = 12V
VCC = 12V Enable Rising
EN=5V
EN=0V
-10
LDO3_3 disabled, all channels disabled
VCC Supply Current in STANDBY
440
600
µA
GPIOs programmed as inputs
VCC=12V,EN = 5V
VCC Supply Current 2ch PFM
3.1
mA
2 channels on set at 5V, VOUT forced to
5.1V, no load, non-switching, Ultra-sonic
off, VCC=12 V, No I2C activity.
VCC Supply Current 4ch PFM
4.0
mA
4 channels on set at 5V, VOUT forced to
5.1V, no load, non-switching, Ultra-sonic
off, VCC=12V, No I2C activity.
VCC Supply Current ON
18
mA
All channels enabled, Fsw=600kHz, gate
drivers unloaded, No I2C activity.
© 2012 Exar Corporation
2/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
INPUT VOLTAGE RANGE AND UNDERVOLTAGE LOCKOUT
Parameter
VCC Range
Min.
Typ.
Max.
Units
5.5
25
V
4.75
5.5
V
Conditions
•
•
With VCC connected to LDO5
VOLTAGE FEEDBACK ACCURACY AND OUTPUT VOLTAGE SET POINT RESOLUTION
Parameter
VOUT Regulation Accuracy
Low Output Range
0.6V to 1.6V
PWM Operation
VOUT Regulation Accuracy
Mid Output Range
0.6V to 3.2V
PWM Operation
VOUT Regulation Accuracy
High Output Range
0.6V to 5.5V
PWM Operation
VOUT Regulation Range
Min.
Typ.
-5
-20
-7.5
-22.5
-15
-45
-20
-50
-30
-90
-40
-100
0.6
Max.
Units
5
20
7.5
22.5
15
45
20
50
30
90
40
100
5.5
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
V
Conditions
•
•
•
•
•
•
•
0.6 ≤ VOUT ≤ 1.6V
0.6 ≤ VOUT ≤ 1.6V
VCC=LDO5
0.6 ≤ VOUT ≤ 3.2V
0.6 ≤ VOUT ≤ 3.2V
VCC=LDO5
0.6 ≤ VOUT ≤ 5.5V
0.6 ≤ VOUT ≤ 4.2V
VCC=LDO5
Without external divider network
12.5
25
50
mV
Low Range
Mid Range
High Range
VOUT Fine Set Point Resolution1
2.5
5
10
mV
Low Range
Mid Range
High Range
VOUT Input Resistance
120
90
75
kΩ
Low Range
Mid Range
High Range
VOUT Input Resistance in PFM
Operation
10
1
0.67
MΩ
Low Range
Mid Range
High Range
VOUT Native Set Point
Resolution
Power Good and OVP Set Point
Range (from set point)
-155
-310
-620
157.5
315
630
mV
Low Range
Mid Range
High Range
Power Good and OVP Set Point
Accuracy
-5
-10
-20
5
10
20
mV
Low Range
Mid Range
High Range
16
V
BFB Set Point Range
9
BFB Set Point Resolution
BFB Accuracy
1
-0.5
V
0.5
V
Note 1: Fine Set Point Resolution not available in PFM
© 2012 Exar Corporation
3/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
CURRENT AND AUX ADC (MONITORING ADCS)
Parameter
Current Sense Accuracy
Min.
Typ.
Max.
Units
-3.75
-10
-5
-12.5
±1.25
3.75
10
5
+12.5
mV
mV
mV
mV
LSB
±2.5
Current Sense ADC INL
+/-0.4
Conditions
•
Low Range (≤120mV) Note 2
-60mV applied
•
High Range (≤280mV)
-150mV
DNL
0.27
Current Limit Set Point
Resolution and Current
Sense ADC Resolution
1.25
mV
Low Range (≤120mV)
2.5
mV
High Range (≤280mV)
mV
Low Range (≤120mV)
Current Sense ADC Range
-120
20
-280
40
15
30
60
VOUT ADC Resolution
VOUT ADC Accuracy
High Range (≤280mV)
Low Range
Mid Range
High Range
mV
-1
1
LSB
VCC ADC Range
4.6
25
V
Note 3
UVLO WARN SET
4.4
4.72
V
UVLO WARN set point 4.6V, VCC=LDO5
UVLO WARN CLEAR
4.4
4.72
V
UVLO WARN set point 4.6V, VCC=LDO5
UVLO FAULT SET (Note 4)
4.2
4.55
V
UVLO FAULT set point 4.4V, VCC=LDO5
VCC ADC Resolution
VCC ADC Accuracy
200
1
-1
Die Temp ADC Resolution
Die Temp ADC Range
mV
5
Vin <= 20V
°C
156
-44
LSB
°C
Output value is in Kelvin
Note 2: Final test limits are ±2.5mV or ±2 LSB
Note 3: Although Range of VCC ADC is technically 0V to 25V, below 4.55 the LDO5 hardware UVLO may have tripped.
Note 4: This test ensures an UVLO FAULT flag will be given before the LDO5 hardware UVLO trips.
LINEAR REGULATORS
Parameter
Min.
Typ.
Max.
Units
Conditions
4.85
5.0
5.15
V
•
5.5V ≤ VCC ≤ 25V
0mA < ILDO5OUT < 130mA, LDO3_3 Off
LDO5 Current Limit
135
155
180
mA
•
LDO5 Fault Set
LDO5 UVLO
4.74
V
•
VCC Rising
LDO5 Output Voltage
LDO5 PGOOD Hysteresis
375
LDO5 Bypass Switch Resistance
1.1
Bypass Switch Activation
Threshold
2.5
Bypass Switch Activation
Hysteresis
mV
1.5
Ω
2.5
%
150
VCC Falling
•
V5EXT Rising, % of threshold setting
V5EXT Falling
mV
3.45
V
•
4.6V ≤ LDO5 ≤ 5.5V
0mA < ILDO3_3OUT < 50mA
85
mA
•
LDO3_3 Fault Set
Maximum total LDO loading
during ENABLE start-up
30
mA
© 2012 Exar Corporation
4/29
LDO3_3 Output Voltage
LDO3_3 Current Limit
3.15
53
3.3
ENABLE transition from logic low to
high. Once LDO5 in regulation above
limits apply.
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
PWM GENERATORS AND OSCILLATOR
Parameter
Max.
Units
105
1230
kHz
fsw Accuracy
–5
5
%
CLOCK IN
Synchronization Frequency
20
25.7
31
MHz
When synchronizing to an external clock
(Range 1)
CLOCK IN
Synchronization Frequency
10
12.8
15.5
MHz
When synchronizing to an external clock
(Range 2)
Min.
Typ.
Max.
Units
0.8
V
1
µA
0.4
V
ISINK = 1mA
V
ISOURCE = 1mA
3.6
V
ISOURCE = 0mA
10
µA
Switching Frequency (fsw)
Range
Min.
Typ.
Conditions
Steps defined in table
GPIOS5
Parameter
Input Pin Low Level
Input Pin High Level
V
2.0
Input Pin Leakage Current
Output Pin Low Level
Output Pin High Level
2.4
Output Pin High Level
Conditions
3.3
Output Pin High-Z leakage
Current (GPIO pins only)
Maximum Sink Current
Open Drain Mode
1
mA
30
MHz
Max.
Units
0.8
V
1
µA
Output Pin Low Level
0.4
V
ISINK = 3mA
Output Pin High Level
15
V
Open Drain. External pull-up resistor to
user supply
Output Pin High-Z leakage
Current (PSIO pins only)
10
µA
5
MHz
I/O Frequency
Note 5: 3.3V CMOS logic compatible, 5V tolerant.
PSIOS6
Parameter
Min.
Input Pin Low Level
Input Pin High Level
Input Pin Leakage Current
I/O Frequency
Typ.
Conditions
V
2.0
Note 6: 3.3V/5.0V CMOS logic compatible, maximum rating of 15.0V
© 2012 Exar Corporation
5/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
SMBUS (I2C) INTERFACE
Parameter
Min.
Typ.
Max.
Units
0.3 VIO
V
VIO = 3.3 V ±10%
0.7 VIO
V
VIO = 3.3 V±10%
0.05 VIO
V
VIO = 3.3 V±10%
0.4
V
ISINK = 3mA
-10
10
µA
Input is between 0.1 VIO and 0.9 VIO
20 + 0.1
Cb
250
ns
With a bus capacitance (Cb)from 10 pF to
400 pF
1
pF
Max.
Units
Input Pin Low Level, VIL
Input Pin High Level, V IH
Hysteresis of Schmitt Trigger
inputs, Vhys
Output Pin Low Level (open
drain or collector), VOL
Input leakage current
Output fall time from VIHmin to
VILmax
Internal Pin Capacitance
Conditions
GATE DRIVERS
Parameter
Min.
Typ.
GH, GL Rise Time
17
ns
GH, GL Fall Time
11
ns
GH, GL Pull-Up On-State Output
Resistance
4
5
Ω
GH, GL Pull-Down On-State
Output Resistance
2
2.5
Ω
GH, GL Pull-Down Resistance in
Off-Mode
Conditions
At 10-90% of full scale, 1nF Cload
50
kΩ
9
Ω
@ 10mA
Minimum On Time
50
ns
1nF of gate capacitance.
Minimum Off Time
Bootstrap diode forward
resistance
VCC = VCCD = 0V.
125
ns
1nF of gate capacitance
Minimum Programmable Dead
Time
20
ns
Maximum Programmable Dead
Time
Tsw
Does not include dead time variation from
driver output stage
Tsw=switching period
Programmable Dead Time
Adjustment Step
607
© 2012 Exar Corporation
ps
6/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
BLOCK DIAGRAM
BST1
Channel 1
VOUT1
Feedback
ADC
PreScaler
1/2/4
GH1
Digital
PID
GL1
GL_RTN1
Current
ADC
SS & PD
VOUT3
Gate
Driver
Dead
Time
VCC
VREF
DAC
LX1
Hybrid
DPWM
VCCD1-2
Channel 2
VOUT3
Channel 3
VCCD3-4
VOUT4
Channel 4
Vout1
4uA
Vout2
ENABLE
Internal
POR
Vout3
MUX
GPIO 0-1
NVM
(FLASH)
Sequencing
PSIO
Configuration
Registers
PWR
Good
I2C
LOGIC
CLOCK
GPIO
PSIO 0-2
SDA,SCL
Vout4
Vtj
BFB
Fault
Handling
OTP
UVLO
OCP
OVP
VCC
LDO5
5V LDO
LDO3_3
3.3V LDO
Fig. 2: XRP7724 Block Diagram
LDO BLOCK DIAGRAM
VCCD3-4
VCCD1-2
LDO5
AVDD
DVDD
1.8V
Regulator
Gate Drivers
1.8V Analog
5V Blocks
PSIO
3.3V Regulator
VCC
5V LDO
3.3V GPIO
1.8V Digital
LDO3_3
3.3V LDO
+
-
4.75V – 4.9V
V5EXT
Fig. 3: XRP7724 LDO Block Diagram
© 2012 Exar Corporation
7/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
PIN ASSIGNMENT
LDO5
V5EXT
BFB
VCC
ENABLE
GL_RTN1
GL1
LX1
GH1
BST1
VCCD1-2
44
43
42
41
40
39
38
37
36
35
34
LDO3_3
1
33
GL_RTN2
AGND
2
32
GL2
CPLL
3
31
LX2
AVDD
4
30
GH2
VOUT1
5
29
BST2
VOUT2
6
28
GL_RTN3
VOUT3
7
27
GL3
VOUT4
8
26
LX3
GPIO0
9
25
GH3
XRP7724
TQFN
7mm X 7mm
Exposed Pad: AGND
GPIO1
10
24
BST3
SDA
11
23
VCCD3-4
GL_RTN4
GH4
22
19
BST4
GL4
18
DGND
21
17
DVDD
LX4
16
PSIO2
20
15
PSIO0
PSIO1
13
SCL
14
12
Fig. 4: XRP7724 Pin Assignment
PIN DESCRIPTION
Name
Pin Number
Description
VCC
41
Input voltage. Place a decoupling capacitor close to the controller IC. This input is used
in UVLO fault generation.
DVDD
16
1.8V supply input for digital circuitry. Connect pin to AVDD. Place a decoupling
capacitor close to the controller IC.
Gate Drive supply. Two independent gate drive supply pins where pin 34 supplies
drivers 1 and 2 and pin 23 supplies drivers 3 & 5. One of the two pins must be
connected to the LDO5 pin to enable two power rails initially. It is recommended that
the other VCCD pin be connected to the output of a 5V switching rail(for improved
efficiency or for driving larger external FETs), if available, otherwise this pin may also
be connected to the LDO5 pin. A bypass capacitor (>1uF) to PAD is recommended for
each VCCD pin with the pin(s) connected to LDO5 with shortest possible length of etch.
VCCD1-2
VCCD3-4
23,34
AGND
2
GL_RTN1-4
39,33, 28,22
Ground connection for the low side gate driver. This should be routed as a signal trace
with GL. Connect to the source of the low side MOSFET.
GL1-GL4
38,32, 27,21
Output pin of the low side gate driver. Connect directly to the gate of an external Nchannel MOSFET.
GH1-GH4
36,30, 25,19
Output pin of the high side gate driver. Connect directly to the gate of an external Nchannel MOSFET.
© 2012 Exar Corporation
Analog ground pin. This is the small signal ground connection.
8/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
Name
Pin Number
Description
37,31, 26,20
Lower supply rail for the GH high-side gate driver. Connect this pin to the switching
node at the junction between the two external power MOSFETs and the inductor. These
pins are also used to measure voltage drop across bottom MOSFETs in order to provide
output current information to the control engine.
BST1-BST4
35,29, 24,18
High side driver supply pin(s). Connect BST to the external capacitor as shown in the
Typical Application Circuit on page 2. The high side driver is connected between the
BST pin and LX pin and delivers the BST pin voltage to the high side FET gate each
cycle.
GPI0-GPIO1
9,10
These pins can be configured as inputs or outputs to implement custom flags, power
good signals, enable/disable controls and synchronization to an external clock.
LX1-LX4
Open drain, these pins can be
on and off, shedding the load
configures as standard logic
configured, but as open drains
used to control external power MOSFETs to switch loads
for fine grained power management. They can also be
outputs or inputs just as any of the GPIOs can be
require an external pull-up when configured as outputs.
PSIO0-PSIO2
13,14,15
SDA, SCL
11,12
VOUT1-VOUT4
5,6,7,8
Connect to the output of the corresponding power stage. The output is sampled at least
once every switching cycle
LDO5
44
Output of a 5V LDO. This is a micro power LDO that can remain active while the rest of
the IC is in shutdown. This LDO is also used to power the internal Analog Blocks.
LDO3_3
1
Output of the 3.3V standby LDO. This is a micro power LDO that can remain active
while the rest of the IC is in shutdown.
ENABLE
40
If ENABLE is pulled high or allowed to float high, the chip is powered up (logic is reset,
registers configuration loaded, etc.). The pin must be held low for the XRP7724 to be
placed into shutdown.
BFB
42
Input from the 15V output created by the external boost supply. When this pin goes
below a pre-defined threshold, a pulse is created on the low side drive to charge this
output back to the original level. If not used, this pin should be connected to GND.
DGND
17
Digital ground pin. This is the logic ground connection, and should be connected to the
ground plane close to the PAD.
CPLL
3
V5EXT
43
AVDD
4
PAD
45
SMBus/I2C serial interface communication pins.
Connect to a 2.2nF capacitor to GND.
External 5V that can be provided. If one of the output channels is configured for 5V,
then this voltage can be fed back to this pin for reduced operating current of the chip
and improved efficiency.
Output of the internal 1.8V LDO.
AVDD and AGND close to the chip.
A decoupling capacitor should be placed between
This is the die attach paddle, which is exposed on the bottom of the part.
externally to the ground plane.
Connect
ORDERING INFORMATION
Part Number
Temperature
Range
Marking
Package
Packing
Quantity
Note 1
I2C Default
Address
XRP7724ILB-F
Bulk
Halogen Free
-40°C≤TJ≤+125°C XRP7724ILB
0x28 (7Bit)
44-pin TQFN
YYWW
X
Halogen Free
2.5K/Tape
&
Reel
-40°C≤TJ≤+125°C
Evaluation kit includes XRP7724EVB-DEMO-1 Evaluation Board with Power
XRP7724EVB-DEMO-2P-KIT
Architect software and XRP77XXEVB-XCM (USB to I2C Exar Configuration Module)
XRP7724ILBTR-F
“YY” = Year – “WW” = Work Week – “X” = Lot Number; when applicable.
© 2012 Exar Corporation
9/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
TYPICAL PERFORMANCE CHARACTERISTICS
All data taken at VCC = 12V, TJ = TA = 25°C, unless otherwise specified - Schematic and BOM from XRP7724EVB. See
XRP7724EVB-DEMO-1 Manual.
Fig. 5: PFM to PWM Transition
Fig. 6 PWM to PFM Transition
Fig. 7 0-6A Transient 300kHz PWM only
Fig. 8 10-6A Transient 300kHz with OVS ±5.5%
Fig. 9 Sequential Start-up
Fig. 10 Sequential Shut Down
© 2012 Exar Corporation
10/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
Example
Fig. 11: Simultaneous Start-up
Fig. 12 Simultaneous Shut Down
Fig. 13: PFM Zero Current Accuracy
Fig. 14: LDO5 Brown Out Recovery, No Load
1.00
0.95
0.90
Vin=25V
Rising
0.85
Vin=25V
Falling
0.80
0.75
Vin=4.75
V Rising
0.70
Vin=4.75
V Falling
0.65
0.60
-40°C
25°C
85°C
125°C
Fig. 15: Enable Threshold Over Temp
© 2012 Exar Corporation
11/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
FEATURES AND BENEFITS
System Integration Capabilities
 Single supply operation
Programmable Power Benefits
 I2C interface allows:
 Communication with a System Controller
or other Power Management devices for
optimized system function
 Fully Configurable
 Output set point
 Feedback compensation
 Frequency set point
 Access to modify or read internal
registers that control or monitor:
 Under voltage lock out
 Input voltage measurement
 Output Current
 Input and Output Voltage
 Gate drive dead time
 Soft-Start/Soft-Stop Time
 ‘Power Good’
 Reduced Development Time
 Configurable and re-configurable for
different Vout, Iout, Cout, and Inductor
values
 Part Temperature




 No need to change external passives for a
new output specification.
 Higher integration and Reliability
 Many external circuits used in the past
can be eliminated significantly improving
reliability.
 Adjusting fault limits and
disabling/enabling faults
 Packet Error Checking (PEC) on I2C
communication
PowerArchitect™ 5.0 Design and
Configuration Software
 5 GPIO pins with a wide range of
configurability
 Fault reporting (including UVLO
Warn/Fault, OCP Warn/Fault, OVP,
Temperature, Soft-Start in progress,
Power Good, System Reset)
 Allows a Logic Level interface with other
non-digital IC’s or as logic inputs to other
devices
 Wizard quickly generates a base design
 Calculates all configuration registers
 Projects can be saved and/or recalled
 GPIOs can be configured easily and
intuitively
 “Dashboard” Interface can be used for
real-time monitoring and debug
 Frequency and Synchronization
Capability
 Selectable switching frequency between
105kHz and 1.2MHz
System Benefits
 Reliability is enhanced via communication
with the system controller which can obtain
real time data on an output voltage, input
voltage and current.
 Main oscillator clock and DPWM clock can
be synchronized to external sources
 System processors can communicate with
the XRP7724 directly to obtain data or
make adjustments to react to circuit
conditions
 ‘Master’, ‘Slave’ and ‘Stand-alone’
Configurations are possible
 Internal MOSFET Drivers
 Internal FET drivers (4Ω/2Ω) per channel
 Built-In Automatic Dead-time adjustment
 A system process or could also be
configured to log and analyze operating
history, perform diagnostics and if required,
take the supply off-line after making other
system adjustments.
© 2012 Exar Corporation
Enable/Disable Outputs
Over Current
Over Voltage
Temperature Faults
 30ns Rise and Fall times
 4 Independent SMPS channels and 2
LDOs in a 7x7mm TQFN
12/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
FUNCTIONAL OVERVIEW
external circuitry. The 3.3V LDO is solely for
customer use and is not used by the chip.
There is also a 1.8V linear which is for internal
use only and should not be used externally.
The XRP7724 is a quad-output digital pulse
width modulation (DPWM) controller with
integrated
gate
drivers
for
use
with
synchronous buck switching regulators. Each
output voltage can be programmed from 0.6V
to 5.5V without the need of an external
voltage divider. The wide range of the
programmable DPWM switching frequency
(from 105 kHz to 1.2 MHz) enables the user to
optimize for efficiency or component sizes.
Since the digital regulation loop requires no
external
passive
components,
loop
performance is not compromised due to
external component variation or operating
condition.
A key feature of the XRP7724 is its powerful
power management capabilities. All four
outputs are independently programmable and
gives the user not only full control of the
delay, ramp, and sequence during power up
and power down. One can also control of how
the outputs interact and power down in the
event of a fault. This includes active ramp
down of the output voltages to remove an
output voltage as quickly as possible. Another
nice feature is that the outputs can be defined
and controlled as groups.
The XRP7724 has two main types of
programmable memory. The first types are
runtime registers that contain configuration,
control and monitoring information for the
chip. The second type is rewritable NonVolatile Flash Memory (NVFM) that is used for
permanent storage of the configuration data
along with various chip internal functions.
During power up the run time registers are
loaded from the NVFM allowing for standalone
operation.
The XRP7724 provides a number of critical
safety
features, such
as
Over-Current
Protection (OCP), Over-Voltage Protection
(OVP), Over Temperature Protection (OTP)
plus input Under Voltage Lockout (UVLO). In
addition, a number of key health monitoring
features such as warning level flags for the
safety functions, Power Goods (PGOOD), etc.,
plus full monitoring of system voltages and
currents. The above are all programmable
and/or readable from the SMBus and many
are steerable to the GPIOs for hardware
monitoring.
The XRP7724 brings an extremely high level of
functionality
and
performance
to
a
programmable
power
system.
Ever
decreasing product budgets require the
designer
to
quickly
make
good
cost/performance tradeoffs to be truly
successful. By incorporating 4 switching
channels, two user LDOs, a charge pump
boost controller, along with internal gate
drivers, all in a single package, the XRP7724
allows for extremely cost effective power
system designs. Another key cost factor to
put into the cost tradeoffs, which is often
overlooked, is the unanticipated Engineering
Change Order (ECO). The programmable
versatility of the XRP7724, along with the lack
of hard wired, on board configuration
components, allows for minor and major
changes to be made, in circuit, on the board
by simple reprogramming.
For hardware communication, the XRP7724
has two logic level General Purpose InputOutput (GPIO) pins and three, 15V, open
drain, Power System Input-Output (PSIO)
pins. Two pins are dedicated to the SMBus
data (SDA) and clock (SCL). Additional pins
include Chip Enable (Enable), Aux Boost
Feedback (BFB) and External PLL Capacitor
(CPLL).
In addition to providing four switching outputs,
the XRP7724 also provides control for an Aux
boost supply, and two stand-by linear
regulators that produce 5V and 3.3V for a total
of 7 customer usable supplies in a single
device.
The 5V LDO is used for internal power and is
also available for customer use to power
© 2012 Exar Corporation
13/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
THEORY OF OPERATION
CHIP ARCHITECTURE
REGULATION LOOPS
Vin
(VCC)
Vref
DAC
VFB
(VOUTx)
Scalar
÷1,2,4
AFE
Error
Amp
AFE
ADC
Window
Comp.
Fine
Adjust
Vin Feed
Forward
Error
Register
PID
Vdrive
(VCCD)x
DPWM
Gate
Driver
GHx
GLx
LXx
Current
ADC
OVS
PFM/
Ultrasonic
PWMPFM Sel
Fig 16 XRP7724 Regulation Loops
Figure 16 shows a functional block diagram of
the regulation loops for an output channel.
There are four separate parallel control loops;
Pulse
Width
Modulation
(PWM),
Pulse
Frequency Modulation (PFM), Ultrasonic, and
Over Sampling (OVS). Each of these loops is
fed by the Analog Front End (AFE) as shown at
the left of the diagram. The AFE consist of an
input voltage scalar, a programmable Voltage
Reference (Vref) DAC, Error Amplifier, and a
window comparator. (Please note that the
block diagram shown is simplified for ease of
understanding. Some of the function blocks
are common and shared by each channel by
means of a multiplexer.)
up to 1.6V (low range) the scalar has a gain of
1. For output voltages from 1.6V to 3.2V (mid
range) the scalar gain is 1/2 and for voltages
greater than 3.2V (high range) the gain is 1/4.
This results in the low range having a
reference voltage resolution of 12.5mV, mid
range of 25mV and the high range having a
resolution of 50mV. The error amp has a gain
of 4 and compares the output voltage of the
scalar to Vref to create an error voltage on its
output. This is converted to a digital error
term by the AFE ADC which is stored in the
error register. The error register has a fine
adjust function that can be used to improve
the output voltage set point resolution by a
factor of 5 resulting in a low range resolution
of 2.5mV, mid range resolution of 5mV and a
high range resolution of 10mV. The output of
the error resister is then used by the
Proportional
Integral
Derivative
(PID)
controller to manage the loop dynamics.
PWM Loop
The PWM loop operates in Voltage Control
Mode (VCM) with optional Vin feed forward
based on the voltage at the VCC pin. The
reference voltage (Vref) for the error amp is
created by a 0.15V to 1.6V DAC that has a
12.5mV resolution. In order to get a full 0.6V
to 5.5V output voltage range an input scalar is
used to reduce feedback voltages for higher
output voltages to bring them within the 0.15V
to 1.6V control range. So for output voltages
© 2012 Exar Corporation
The XRP7724 PID is a 17-bit five coefficient
control engine that calculates the correct duty
cycle under the various operating conditions
and feeds it to the Digital Pulse Width
Modulator (DPWM). Besides the normal
14/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
coefficients the PID also uses the Vin voltage
to provide a feed forward function.
The PFM loop works in conjunction with the
PWM loop and is entered when the output
current falls below a programmed threshold
level for a programmed number of cycles.
When PFM mode is entered, the PWM loop is
disabled and instead, the scaled output
voltage is compared to Vref with a window
comparator. The window comparator has three
thresholds; normal (Vref), high (Vref +
%high) and low (Vref - %low). The %high and
%low values are programmable and track
Vref.
The XRP7724 DPWM includes a special delay
timing loop that gives a timing resolution that
is 16 times the master oscillator frequency
(103MHz) for a timing resolution of 607ns for
both the driver pulse width and dead time
delays. The DWPM creates and outputs the
Gate High (GH) and Gate Low (GL) signals to
the driver. The maximum and minimum on
times and dead time delays are programmable
by configuration resisters.
In PFM mode, the normal comparator is used
to regulate the output voltage. If the output
voltage falls below the Vref level, the
comparator is activated and triggers the
DPWM to start a switching cycle. When the
high side FET is turned on, the inductor
current ramps up which charges up the output
capacitors and increasing their voltage. After
the completion of the high side and low side
on-times, the lower FET is turned off to inhibit
any inductor reverse current flow. The load
current then discharges the output capacitors
until the output voltage falls below Vref and
the normal comparator is activated this then
triggers the DPWM to start the next switching
cycle. The time from the end of the switching
cycle to the next trigger is referred to as the
dead zone. This PFM methodology ensures
output voltage ripple does not increase from
PWM to PFM.
To provide current information, the output
inductor current is measured by a differential
amplifier that reads the voltage drop across
the RDS of lower FET during its on time. There
are two selectable ranges, a low range with a
gain of 8 for a +20mV to -120 mV range and a
high range with a gain of 4 for +40mV to 280mV range. The optimum range to use will
depend on the maximum output current and
the RDS of the lower FET. The measured
voltage is then converted to a digital value by
the current ADC block. The resulting current
value is stored in a readable register and also
used to determine when PWM to PFM
transitions should occur.
PFM mode loop
The XRP7724 has a PFM loop that can be
enabled to improve efficiency at light loads.
By reducing switching frequency and operating
in the discontinuous conduction mode (DCM),
both switching and I2R losses are minimized.
When PFM mode is initially entered the
switching duty cycle is the same that it was in
PWM mode. The cause the inductor ripple
current to be the same level that it was in
PWM mode. During operation the PFM duty
cycle is calculated based on the ratio of the
output voltage to VCC.
Figure 17 shows a functional diagram of the
PFM logic.
# Cycles Reg
Default = 20
A
CHx Fsw
PFM Current
Threshold Reg
Clk
A
COUNTER
If the output voltage ever goes outside the
high/low windows, PFM mode is exited and the
PWM loop is reactivated.
A<B
Clear
B
A<B
IADC
B
VOUT
S
Q
R
Q
PFM MODE
+
VREF HIGH
-
-
VREF
+
VREF LOW
+
Although the PFM mode does a good job in
improving efficiency at light load, at very light
loads the dead zone time can increase to the
point where the switching frequency can enter
the audio hearing range. When this happens
some components, like the output inductor
and ceramic capacitors, can emit audible
noise. The amplitude of the noise depends
PWM MODE
PFM EXIT
TRIGGER PULSE
-
Fig 17: PFM Enter/Exit Functional Diagram
© 2012 Exar Corporation
15/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
mostly on the board design and on the
manufacturer and construction details of the
components. Proper selection of components
can reduce the sound to very low levels. In
general Ultrasonic Mode is not used unless
required as it reduces light load efficiency.
delay of up to one switching cycle before the
control loop can respond. With OVS enabled if
output voltage drops below the lower level, an
immediate GH pulse will be generated and
sent to the driver to increase the output
inductor current toward the new load level
without having to wait for the next cycle to
begin. If the output voltage is still below the
lower limit at the beginning of the next cycle,
OVS will work in conjunction with the PID to
insert additional GH pulses to quickly return
the output voltage back within its regulation
band. The result of this system is transient
response capabilities on par or exceeding
those of a constant on-time control loop.
Ultrasonic Mode
Ultrasonic mode is an extension of PFM to
ensure that the switching frequency never
enters the audible range. When this mode is
entered, the switching frequency is set to
30kHz and the duty cycle of the upper and
lower FETs, which are fixed in PFM mode, are
decreased as required to keep the output
voltage in regulation while maintaining the
30kHz switching frequency.
Over Voltage OVS: When there is a step load
current decrease, the output voltage will
increase (bump up) as the excess inductor
current that is no longer used by the load,
flows into the output capacitors causing the
output voltage to rise.
The voltage will
continue to rise until the inductor current
decreases to the new load current. With OVS
enabled, if the output voltage exceeds the
high limit of the window comparator, a
blanking pulse is generated to truncate the GH
signal. This causes inductor current to
immediately begin decreasing to the new load
level. The GH will continue to be blanked until
the output voltage falls below the high limit.
Again, since the output voltage is sampled at
four times the switching frequency, over shoot
will be decreased and the time required to get
back into the regulation band is also
decreased.
Under extremely light or zero load currents,
the GH on time pulse width can decrease to its
minimum width. When this happens, the lower
FET on time is increased slightly to allow a
small amount of reverse inductor to flow back
into Vin to keep the output voltage in
regulation while maintaining the switching
frequency above the audio range.
Oversampling OVS Mode
Oversampling (OVS) mode is a feature added
to the XRP7724 to improve transient
responses. This mode can only be enabled
when the channel switching frequency is
operating in 1x frequency mode. In OVS mode
the output voltage is sampled 4 times per
switching cycle and is monitored by the AFE
window comparator. If the voltage goes
outside the set high or low limits, the OVS
control electronics can immediately modify the
pulse width of the GH or GL drivers to respond
accordingly, without having to wait for the
next cycle to start. OVS has two types of
response depending on whether the high limit
is exceeded during an unloading transient
(Over Voltage), or the low limit is exceeded
during a loading transient (Under Voltage).
OVS can be used in conjunction with both the
PWM and PFM operating modes. When it is
activated it can noticeably decrease output
voltage excursions when transitioning between
PWM and PFM modes.
INTERNAL DRIVERS
The internal high and low gate drivers use
totem pole FETs for high drive capability. They
are powered by two external 5V power pins
(VCCD1-2) and (VCCD3-4), VCCD1-2 powers
the drivers for channels 1 and 2 and VCCD3-4
powers channels 3 and 4. The drivers can be
powered by the internal 5V LDO by connecting
their power pins to the LDO5 output through
Under Voltage OVS: If there is an increasing
current load step, the output voltage will drop
until the regulator loop adapts to the new
conditions to return the voltage to the correct
level. Depending on where in the switching
cycle the load step happens there can be a
© 2012 Exar Corporation
16/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
an RC filter to avoid conducted noise back into
the analog circuitry.
(VCC) supply. The output of LDO5 should be
bypassed by a good quality capacitor
connected between the pin and ground close
to the device. The 5V output is used by the
XRP7724 as a standby power supply and is
also used to power the 3.3V and 1.8V linear
regulators inside the chip and can also supply
power to the 5V gate drivers. The total output
current that the 5V LDO can provide is 130mA.
The XRP7724 consumes approximately 20mA
and the rest is shared between LDO3_3 and
the gate drive currents. During initial power
up, the maximum external load should be
limited to 30mA.
To minimize power dissipation in the 5V LDO it
is recommended to power the drivers from an
external 5V power source either directly or by
using the V5EXT input. Good quality 1uF to
4.7uF capacitors should be connected directly
between the power pins to ground to optimize
driver performance and minimize noise
coupling to the 5V LDO supply.
The driver outputs should be connected
directly
to
their
corresponding
output
switching FETs, with the Lx output connected
to the drain of the lower FET for the best
current monitoring accuracy.
The 3.3V LDO output available on the LDO3_3
pin is solely for customer use and is not used
internally. This supply may be turned on or off
by the configuration registers. Again a good
bypass capacitor should be used.
See ANP-32 “Practical Layout Guidelines for
PowerXR Designs”
LDOS
The AVVD pin is the 1.8V regulator output and
needs to be connected externally to the DVVD
pin on the device. A good quality capacitor
should be connected between this pin and
ground close to the package.
The XRP7724 has two internal Low Drop Out
(LDO) linear regulators that generate 5.0V
(LDO5) and 3.3V (LDO3_3) for both internal
and external use. Additionally it also has a
1.8V regulator that supplies power for the
XRP7724 internal circuits. Figure 3 shows a
block diagram of the linear power supplies.
LDO5 is the main power input to the device
and is supplied by an external 5.5V to 25V
For operation with a VCC of 4.75V to 5.5V, the
LDO5 output needs to be connected directly to
VCC on the board.
CLOCKS AND TIMING
¸4/¸8
Reg
Clock
Divider
PLL
Ext Clock Output
GPIO1
Freg Mult Reg
DPWM
System Clock
Ext Clock Input
GPIO0
SEL
Base Frequency
x4/x8
Reg
2x
Frequency
Set Reg
4x
CH1 Timing
Sequencer
To Channels 2®4
Fig 18 XRP7724 Timing Block Diagram
© 2012 Exar Corporation
17/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
Figure 18 shows a simplified block diagram of
the XRP7724 timings. Again, please note that
the function blocks and signal names used are
chosen for ease of understanding and do not
necessarily reflect the actual design.
Base
Frequency
The system timings are generated by a
103MHz internal system clock (Sys_Clk).
There are two ways that the 103 MHz system
clock can be generated. These include an
internal oscillator and a Phase Locked Loop
(PLL) that is synchronized to an external clock
input. The basic timing architecture is to
divide the Sys_Clk down to create a
fundamental switching frequency (Fsw_Fund)
for all the output channels that is settable
from 105kHz to 306kHz. The switching
frequency for a channel (Fsw_CHx) can then
be selected as 1 times, 2 times or 4 times the
fundamental switching frequency.
To set the base frequency for the output
channels a “Fsw_Set” value representing the
base frequency shown in Table 1, is entered
into the switching frequency configuration
register (Fsw_Set is basically equal to the
base frequency times 256). The system
timings are then created by dividing down
Sys_Clk to produce a base frequency clock,
2X and 4X times the base frequency clocks,
and sequencing timing to position the output
channels relative to each other. Each output
channel then has its own frequency multiplier
register that is used to select its final output
switching frequency.
Table 1 shows the available channel switching
frequencies for the XRP7724 device. In
practice the PowerArchitect™ 5.0 design tool
handles all the details and the user only has
to enter the fundamental switching frequency
and the 1x, 2x, 4x frequency multiplier for
each channel.
kHz
Available 2x
Frequencies
kHz
Available 4x
Frequencies
kHz
105.5
107.3
109.1
111.0
112.9
115.0
117.0
119.2
121.5
123.8
126.2
128.8
131.4
134.1
137.0
139.9
143.1
146.3
149.7
153.3
157.0
160.9
165.1
169.4
174.0
178.8
183.9
189.3
195.1
201.2
207.7
214.6
222.0
229.9
238.4
247.6
257.5
268.2
279.9
292.6
306.5
211.1
214.6
218.2
222.0
225.9
229.9
234.1
238.4
242.9
247.6
252.5
257.5
262.8
268.2
273.9
279.9
286.1
292.6
299.4
306.5
314.0
321.9
330.1
338.8
348.0
357.6
367.9
378.7
390.2
402.3
415.3
429.2
444.0
459.8
476.9
495.2
515.0
536.5
559.8
585.2
613.1
422.1
429.2
436.4
444.0
451.8
459.8
468.2
476.9
485.8
495.2
504.9
515.0
525.5
536.5
547.9
559.8
572.2
585.2
598.8
613.1
628.0
643.8
660.3
677.6
695.9
715.3
735.7
757.4
780.3
804.7
830.6
858.3
887.9
919.6
953.7
990.4
1030.0
1072.9
1119.6
1170.5
1226.2
Table 1
If an external clock is used, the frequencies in
this table will shift accordingly.
© 2012 Exar Corporation
18/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
SUPERVISORY AND CONTROL
 General Output – set with
command
Power system design with XRP7724 is
accomplished using PowerArchitect™ design
tool version 5 (PA5). All figures referenced in
the following sections are taken from PA5.
Furthermore, the following sections reference
I2C commands. For more on these commands
please refer to ANP-38.
an I2C
 General Input – triggers an interrupt;
state read with an I2C command
 Power Group Enable – controls
enabling and disabling of Group 1 and
Group 2
 Power Channel Enable – controls
enabling and disabling of a individual
channel including LDO3.3
DIGITAL I/O
 I2C Address Bit – controls an I2C
address bit
XRP7724 has two General Purpose Input
Output (GPIO) and three Power System Input
Output (PSIO) user configurable pins.
 Power OK – indicates that selected
channels have reached
their target
levels and have not faulted. Multiple
channel selection is available in which
case the resulting signal is the AND logic
function of all channels selected
 ResetOut – is delayed Power OK. Delay
is programmable in 1msec increments
with the range of 0 to 255 msecs
 Low Vcc – indicates when Vcc has fallen
below the UVLO fault threshold and
when the UVLO condition clears (Vcc
voltage rises above the UVLO warning
level)
 GPIOs are 3.3V CMOS logic compatible
and 5V tolerant.
 PSIO configured as outputs are open
drain and require external pull-up
resistor. These I/Os are 3.3V and 5V
CMOS logic compatible, and up to 15V
capable.
 Interrupt – the controller generated
interrupt selection and clearing is done
through I2C commands
Interrupt, Low Vcc, Power OK and ResetOut
signals can only be forwarded to a single
GPIO/PSIO.
The polarity of the GPIO/PSIO pins is set in
PA5 or with an I2C command.
In addition, the following are functions that
are unique to GPIO0 and GPIO1.
Configuring GPIO/PSIOs
The following functions can be controlled from
or forwarded to any GPIO/PSIO:
© 2012 Exar Corporation
19/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
HW Flags – these are hardware monitoring
functions forwarded to GPIO0 only. The
functions include Under-Voltage Warning,
Over- Temperature Warning, Over-Voltage
Fault, Over-Current Fault and Over -Current
Warning for every channel. Multiple selection
is available in which case the resulting signal
is the OR logic function
 “PGood Max” is the upper window and
“PGood Min” is the lower window. The
minimum and maximum for each of these
values can be calculated by the following
equation:
 External
Clock-in
–
enables
the
controller to lock to an external clock
including one from another XRP7724
applied to the GPIO0 pin. There are two
ranges of clock frequencies the controller
accepts, selectable by a user
 Where N =1 to 63 for the PGOOD Max
value and N=1 to 62 for the PGOOD Min
value.
For example, with the target
voltage of 1.5V and set point resolution of
2.5mV (LSB), the Power Good min and
max values can range from 0.17% to
10.3% and 0.17% to 10.5% respectively.
A user can effectively double the values
by changing to the next higher output
voltage range setting, but at the expense
of reduced set point resolution.
 External Clock-out – clock sent out
through GPIO1 for synchronizing with
another XRP7724 (see the clock out
section for more information).
FAULT HANDLING
There are seven different types of fault
handling:
 HW Power Good – the Power Good
hardware monitoring function. It can only
be forwarded to GPIO1. It is an output
voltage monitoring function that is a
hardware comparison of channel output
voltage against its user defined Power
Good threshold limits (Power Good
minimum and maximum levels). . It has
no hysteresis. Multiple channel selection is
available in which case the resulting signal
is the AND logic function of all channels
selected.
 Under
Voltage
Lockout
(UVLO)
monitors voltage supplied to the Vcc pin
and will cause the controller to shutdown
all channels if the supply drops to critical
levels.
 Over Temperature Protection (OTP)
monitors temperature of the chip and will
cause the controller to shutdown all
channels if temperature rises to critical
levels.
 Over
Voltage
Protection
(OVP)
monitors regulated voltage of a channel
and will cause the controller to react in a
user specified way if the regulated voltage
surpasses threshold level.
 Over
Current
Protection
(OCP)
monitors current of a channel and will
cause the controller to react in a user
 The Power Good minimum and maximum
levels are expressed as percentages of the
target voltage.
© 2012 Exar Corporation
20/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
specified way if the current level
surpasses threshold level.
 Start-up Time-out Fault monitors if a
channel gets into regulation in a user
defined time period
 LDO5 Over Current Protection (LDO5
OCP) monitor current drawn from the
regulator and will cause the controller to
be reset if the current exceeds LDO5 limit
(155mA typical)
 LDO3.3
Over
Current
Protection
(LDO3.3 OCP) monitors current drawn
from the regulator and will cause the
controller to shut down the regulator if the
current exceeds LDO3.3 current limit
(65mA typical)
level at 4.6V may result in the outputs not reenable until a full 5.0V is reached on Vcc.
Setting the warning level to 4.6v and the fault
level at 4.4V would likely make UVLO handing
as desired, however, below 4.6V the device
has a hardware UVLO on LDO5 to ensure
proper shutdown of the internal circuitry of
the controller. This means the 4.4V UVLO
fault level will never occur. A special test has
been added to ensure that if UVLO FAULT will
OTP
User defined OTP warning, fault and restart
levels are set at 5°C increments in PA5.
UVLO
Both UVLO warning and fault levels are user
programmable and set at 200mV increments
in PA5.
When the warning level is reached
controller
will
generate
UVLO_WARNING_EVENT
interrupt.
addition, the host can be informed about
event through HW Flags on GPIO0 (see
Digital I/O section).
When the warning level is reached
controller
will
generate
TEMP_WARNING_EVENT
interrupt.
addition, the host can be informed about
event through HW Flags on GPIO0 (see
Digital I/O section).
the
the
In
the
the
When an OTP fault condition occurs, the
XRP7724 outputs are shutdown and the
TEMP_OVER_EVENT interrupt is generated.
Once temperature reaches a user defined OTP
Restart
Threshold
level,
the
TEMP_UNDER_EVENT
interrupt
will
be
generated and the controller will reset.
When an under voltage fault condition occurs,
the XRP7724 outputs are shutdown and the
UVLO_FAULT_ACTIVE_EVENT
interrupt
is
generated. In addition, the host can be
informed by forwarding the Low Vcc signal to
any GPIO/PSIO (see the Digital I/O section).
This signal transitions when the UVLO fault
occurs. When coming out of the fault, rising
Vcc crossing the UVLO fault level will trigger
the UVLO_FAULT_INACTIVE_EVENT interrupt.
OVP
A user defined OVP fault level is set in PA5
and is expressed in percentages of a
regulated target voltage.
Once UVLO condition clears (Vcc voltage rises
Above or TO the user defined UVLO warning
level), the Low Vcc signal will transition and
the controller will be reset.
Resolution is the same as for the target
voltage (expressed in percentages). The OVP
minimum and maximum values are calculated
by the following equation where the range for
N is 1 to 63:
A special attention needs to be paid in the
case when Vcc = LDO5 = 4.75V to 5.5V.
Since the input voltage ADC resolution is
200mV, the UVLO warning and fault set
points are coarse for a 5V input. Therefore,
setting the warning level at 4.8V and the fault
© 2012 Exar Corporation
the
the
In
the
the
When the OVP level is reached and the fault is
generated, the host will be notified by the
21/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
SUPPLY_FAULT_EVENT interrupt generated by
the controller. The host then can use anI2C
command to check which channel is at fault.
as defined in the electrical characteristics.
The maximum value the user can program is
limited by Rdson of the synchronous Power
FET and current monitoring ADC range. For
example, using a synchronous FET with Rdson
of 30mΩ, using the wider ADC range, the
maximum current limit programmed would
be:
In addition, OVP fault can be monitored
through GPIO0.
A user can choose one of three options on
how to react to an OVP event: to shutdown
the faulting channel, to shut down faulting
channel and to perform auto-restart of the
channel, or to restart the chip.
The current is sampled approximately 30ns
before the low side MOSFET turns off, so the
actual measured DC output current in this
example would be 9.33A plus approximately
half the inductor ripple.
An OCP Fault is considered to have occurred
only if the fault threshold has been tripped in
4 consecutive switching cycles. When the
switching frequency is using the 4x multiplier,
the current is sampled only every other cycle.
As a result it can take as many as 8 switching
cycles for an over current event to be
detected.
When operating in 4x mode
inductors with a soft saturation characteristic
are recommended.
In the case of shutting down the faulting
channel and auto-restarting, the user has an
option to specify startup timeout (the time in
which the fault is validated) and hiccup
timeout (the period after which the controller
will try to restart the channel) periods in 1
msec increments with a maximum value of
255 msec.
When the OCP level is reached and the fault is
generated, the host will be notified by the
SUPPLY_FAULT_EVENT interrupt generated by
the controller. The host then can use an I2C
command to check which channel is at fault.
In addition, OCP fault can be monitored
through HW Flags on GPIO0. The host can
also monitor OCP warning flag through HW
Flags on GPIO0. The OCP warning level is
calculated by PowerArchitect™ as 85% of the
OCP fault level.
Note: a channel will share a response to an
OVP or OCP event.
A user can choose one of three options on
how to react to an OCP event: to shutdown
the faulting channel, to shut down faulting
channel and to perform auto-restart of the
channel, or to restart the chip.
OCP
A user defined OCP fault level is set with 1mA
increments in PA5. PA5 uses calculations to
give the user the approximate DC output
current entered in the current limit field.
However the actual current limit trip value
programmed into the part is limited to 280mV
© 2012 Exar Corporation
The output current reported by the XRP7724
is processed through a 7 sample median filter
in order to reduce noise. The OCP limit is
compared against unfiltered ADC output.
22/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
V5EXT SWITCHOVER
The V5EXT gives a user an opportunity to
supply an external 5 Volt rail to the controller
in order to reduce the controller’s power
dissipation. The 5 Volt rail can be an
independent power rail present in a system or
any of 7724 channels regulated to 5 Volts (in
the PFM mode in particular) and routed back
to the V5EXT pin. It is important to mention
that voltage to Vcc must be applied all the
time even after the switchover in which case
the current drawn from Vcc supply will be
minimal.
In the case of shutting down the faulting
channel and auto-restarting, the user has an
option to specify startup timeout (the time in
which the fault is validated) and hiccup
timeout (the period after which the controller
will try to restart the channel) periods in 1
msec increments with a maximum value of
255 msec.
If the function not used, we recommend the
pin to be either grounded or left floating in
conjunction with making sure the function
gets disabled through register settings.
Note: a channel will share a response to an
OCP or OVP event.
V5EXT switchover control
The function is enabled in PA5. The
switchover thresholds are programmable in
50mV steps with a total range of 200mV.
Hysteresis to go in-out is 150mV. LDO5
automatically turns off when the external
voltage is switched in and turns on when the
external voltage drops below the lower
threshold.
Start-up Time-out Fault
A channel will be at Start-up Time-out Fault if
it does not come-up in a time period specified
in the “Startup Timeout” box. In addition, a
channel is at Start-up Timeout Fault if in prebias configuration voltage is a defined value
too close to the target.
When the fault is generated, the host will be
notified
by
the
SUPPLY_FAULT_EVENT
interrupt generated by the controller. The
host then can use an I2C command to check
which channel is at fault.
LDO5 OCP
When current is drawn from LDO5 exceeds
LDO5 current limit the controller gets reset.
When the controller switches over to the
V5EXT rail, the V5EXT_RISE interrupt is
generated to inform the host. Similarly, when
the controller switches out, the V5EXT_FALL
interrupt gets generated.
LDO3.3 OCP
When current drawn from LDO3.3 exceeds
LDO3.3 current limit the regulator gets shut
down, a fault is generated, and the host will
be notified by the SUPPLY_FAULT_EVENT
interrupt generated by the controller. The
host then can through
an I2C command
check which channel/regulator is at fault.
Once the fault condition is removed, the host
needs to turn the regulator on again.
© 2012 Exar Corporation
EXTERNAL CLOCK SYNCHRONIZATION
XRP7724 can be run off an external clock
available in the system or another XRP7724.
The external clock must be in the ranges of
10.9MHz to 14.7MHz or 21.8MHz to 29.6MHz.
Locking to the external clock is done through
an internal Phase Lock Loop (PLL) which
requires an external loop capacitor of 2.2nF to
23/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
be connected between the CPLL pin and
AGND.
Channels including LDO3.3 can be controlled
independently by any GPIO/PSIO or I2C
command. Channels will start-up or shutdown following transitions of signals applied
to GPIO/PSIOs set to control the channels.
The control can always be overridden with an
I2C command.
In applications where this functionality is not
desired, the CPLL capacitor is not necessary
and can be omitted, and the pin shall be left
floating. In addition, the user needs to make
sure the function gets disabled through
register settings.
Regardless
whether
the
channels
are
controlled independently or are in a group,
the ramp rates specified are followed (see the
Power Sequencing section).
The external clock must be routed to GPIO0.
The GPIO0 setting must reflect the range of
the external clock applied to it: Sys_Clock/8
corresponds to the range of 10.9MHz to
14.7MHz
while
Sys_Clock/4
setting
corresponds to the range of 21.8Mhz to
29.6MHz.
Regulated voltages and voltage drops across
synchronous FET on each switching channel
can be read back using x I2C commands y.
The regulated voltage read back resolution is
15mV, 30mV and 60mV per LSB depending
on the target voltage range. The voltage drop
across synchronous FET read back resolution
is 1.25mV and 2.5mV per LSB depending on
the range.
The
functionality
is
enabled
in
PowerArchitect™ 5.0 by selecting External
Clock-in function under GPIO0.
Through an I2C command the host can check
the status of the channels; whether they are
in regulation or at fault.
For more on details how to monitor PLL lock
in-out, please contact Exar or your local Exar
representative.
Regulated voltages can be dynamically
changed on switching channels using I2C
commands with resolution of 2.5mV, 5mV
and 10mV depending on the target voltage
range (in PWM mode only).
CLOCK OUT
XRP7724 can supply clock out to be used by
another XRP7724 controller. The clock gets
routed out through GPIO1 and can be set to
system clock divided by 8 (Sys_Clock/8) or
system clock divided by 4 (Sys_Clock/4)
frequencies.
For more information on I2C commands
please contact Exar or your local Exar
representative.
POWER SEQUENCING
The functionality is enabled in PA5 by
selecting External Clock-Out function under
GPIO1.
All four channels and LDO3.3 can be grouped
together and as such start-up and shut-down
in a user defined sequence.
Selecting none means channel(s) will not be
assigned to any group and as such will be
controlled independently.
CHANNEL CONTROL
Group Selection
There are three groups:
© 2012 Exar Corporation
24/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
 Group 0 – is controlled by the chip
ENABLE or I2C command. Channels
assigned to this group will come up with
the ENABLE signal being high, and will go
down with the ENABLE signal being low.
The control can always be overridden with
an I2C command.
 Since it is recommended to leave the
ENABLE pin floating in the applications
when Vcc = LDO5 = 4.75V to 5.5V, please
contact Exar for how to configure the
channels to come up at the power up in
this scenario.
 Group 1 – can be controlled by any
GPIO/PSIO or I2C command. Channels
assigned to this group will start-up or
shut-down following transitions of a signal
applied to the GPIO/PSIO set to control
the group. The control can always be
overridden with an I2C command.
 Group 2 – can be controlled by any
GPIO/PSIO or I2C command. Channels
assigned to this group will start-up or
shut-down following transitions of a signal
applied to the GPIO/PSIO set to control
the group. The control can always be
overridden with an I2C command.
milliseconds with a range of 0msec to
255msec.
Shut-down
For each channel within a group a user can
specify
the
following
shut-down
characteristics:
 Ramp Rate – expressed in milliseconds
per Volt. It does not apply to LDO3.3.
 Order – order position of a channel to
come-down within the group
 Wait Stop Thresh? – selecting this
option for a channel means the next
channel in the order cannot start rampingdown until this channel reaches the Stop
Threshold level. The stop threshold level is
fixed at 600mV.
 Delay – additional time delay a user can
specify to postpone a channel shut-down
with respect to the previous channel in the
order. The delay is expressed in
milliseconds with a range of 0msec to
255msec.
Start-up
MONITORING VCC AND TEMPERATURE
Through I2C commands, the host can read
back voltage applied to the Vcc pin and the
die temperature respectively. The Vcc read
back resolution is 200mV per LSB; the die
temperature read back resolution is 5C° per
LSB. For more on I2C commands please refer
to ANP-38 “XRP7724 Command Set and
Programming Guide”.
For each channel within a group a user can
specify the following start-up characteristics:
 Ramp Rate – expressed in milliseconds
per Volt. It does not apply to LDO3.3.
 Order – order position of a channel to
come-up within the group
 Wait PGOOD? – selecting this option for
a channel means the next channel in the
order cannot start ramping-up until this
channel reaches the target level and its
Power Good flag gets asserted.
 Delay – an additional time delay a user
can specify to postpone a channel start-up
with respect to the previous channel in the
order. The delay is expressed in
© 2012 Exar Corporation
PROGRAMMING XRP7724
XRP7724 is a FLASH based device which
means its configuration can be programmed
into FLASH NVM and re-programmed a
number of times.
Programming of FLASH NVM is done through
PA5.
25/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
By clicking on the Flash button, user will start
programming sequence
of the design
configuration into the Flash NVM. After the
programming sequence completes, the chip
will reset (if automatically reset After Flashing
box is checked), and boot the design
configuration from the Flash.
ENABLING XRP7724
XRP7724 has a weak internal pull-up ensuring
it gets enabled as soon as internal voltage
supplies have ramped up and are in
regulation.
Driving the Enable pin low externally will keep
the controller in the shut-down mode. A
simple open drain pull down is the
recommended way to shut XRP7724 down.
If the Enable pin is driven high externally to
control XRP7724 coming out of the shut-down
mode, care must be taken in such a scenario
to ensure the Enable pin is driven high after
Vcc gets supplied to the controller.
For users that wish to create their own
programming procedure so they can reprogram Flash in-circuit using their system
software, please contact Exar for a list of I2C
Flash Commands needed.
In the configuration when Vcc = LDO5 =
4.75V to 5.5V, disabling the device by
grounding
the
Enable
pin
is
not
recommended. At this time we recommend
leaving the Enable pin floating and placing the
controller in the “Standby Mode” instead in
this scenario. The standby mode is defined as
the state when all switching channels and
LDO3.3 are disabled, all GPIO/PSIOs are
programmed as inputs, and system clock is
disabled. In this state chip consumes 440uA
typical.
During a design process a user might want to
repeatedly download a design configuration
onto run time registers without saving it in
Flash. This is done through PA5 as well.
© 2012 Exar Corporation
26/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
Short duration Enable pin toggled low
Short duration shutdown pulses to the
ENABLE pin of the XRP7724 which does not
provide sufficient time for the LDO5 voltage
to fall below 3.5V can result in significant
delay in re-enabling of the device. Some
examples below show LDO5 and ENABLE
pins:
Adding a 200 ohm load on LDO5 pulls voltage
below 3.5V and restart is short.
Note that as VCC increases, the restart time
falls as well. 5.5V input is shown as the worst
case.
Since the ENABLE pin has an internal current
source, a simple open drain pull down is the
recommended way to shut down the
XRP7724. A diode in series with a resistor
between the LDO5 and ENABLE pins may
offer a way to more quickly pull down the
LDO5 output when the ENABLE pin is pulled
low.
No load on LDO5, blue trace. Recovery time
after ENABLE logic high is approximately
40ms.
APPLICATION INFORMATION
available in the system and connected to the
5V EXT pin. If there is no 5V available in the
system, then the power loss will increase
significantly and proper thermal design
becomes critical.
For lower power levels
using properly sized MOSFETs, the use of the
internal 5V regulator as a gate drive supply is
considered appropriate.
THERMAL DESIGN
As a 4 channel controller with internal
MOSFET drivers and 5V gate drive supply all
in one 7x7mm 44pin TQFN package, there is
the potential for the power dissipation to
exceed the package thermal limitations. The
XRP7724 has an internal LDO which supplies
5V to the internal circuitry and MOSFET
LAYOUT GUIDELINES
Refer to application note ANP-32 “Practical
Layout Guidelines for PowerXR Designs”.
drivers during startup.
It is generally
expected that either one of the switching
regulator outputs is 5V or another 5V rail is
© 2012 Exar Corporation
27/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
PACKAGE SPECIFICATION
44-PIN 7X7MM TQFN
© 2012 Exar Corporation
28/29
Rev. 1.0.1
XRP7724
Quad Channel Digital PWM/PFM
Programmable Power Management System
REVISION HISTORY
Revision
Date
Description
1.0.0
10/04/2012
Initial Release of Data Sheet
1.0.1
10/04/2012
Eliminated “Native GH, GL Rise and Fall Time” typical specification.
FOR FURTHER ASSISTANCE
Email:
[email protected]
[email protected]
Exar Technical Documentation:
http://www.exar.com/TechDoc/default.aspx?
EXAR CORPORATION
HEADQUARTERS AND SALES OFFICES
48720 Kato Road
Fremont, CA 94538 – USA
Tel.: +1 (510) 668-7000
Fax: +1 (510) 668-7030
www.exar.com
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve
design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein,
conveys no license under any patent or other right, and makes no representation that the circuits are free of patent
infringement. Charts and schedules contained herein are only for illustration purposes and may vary depending upon a
user’s specific application. While the information in this publication has been carefully checked; no responsibility, however,
is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect
safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives,
writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes
such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
or
its
in
all
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2012 Exar Corporation
29/29
Rev. 1.0.1