PX1002 ® • • • • • • Designed for TDMA IS-54 Receiver IF Applications Low Insertion Loss Excellent Selectivity Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Pb Complies with Directive 2002/95/EC (RoHS) 86.85 MHz SAW Filter Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile °C SM13365-12 260°C for 30 s Electrical Characteristics Characteristic Nominal Center Frequency Passband Sym fC Insertion Loss at fc 3 dB Passband IL GDV Min 1 BW3 Amplitude Ripple over fc ±15 kHz Group Delay Variation over fc ±10 kHz Notes ±12 Typ 86.850 Max Units MHz 3 4.0 dB 1.0 dBP-P 6.0 µsP-P -95 dBm ±25 1, 2 Third-Order Intermod. for -20 dBm tones at fc ±60 & 120 kHz Rejection fc ±60 kHz 11 fc -880 kHz to fc -940 kHz 1, 2, 3 16 65 Ultimate dB 65 TA Operating Temperature Range kHz 1 Impedance Matching to 50 Ω unbalanced +70 -20 °C External L-C Case Style SM13365-12 13.3 X 6.5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM PX1002 YYWW Electrical Connections Connection Terminals Port 1Hot 2 Port 1 Gnd Return 3 Port 2 Hot 8 Port 2 Gnd Return Case Ground 9 All Others Notes: 1. 2. 3. 4. 5. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. 6. 7. 8. 9. 10. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. E-mail: [email protected] http://www.rfm.com PX1002 112904 86.85 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com PX1002 112904 86.85 MHz SAW Filter Quantity Per Reel 254 "B" REF. 100 REF. Tape and Reel Specifications 100 Min 1000 Max See Detail "A" 13. 0 12.0 24.4 20 21.0 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.0 mm Bo 13.8 mm Ko 2.0 mm Pitch 12.0 mm W 24.0 mm PIN #1 USER DIRECTION OF FEED RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com PX1002 112904 86.85 MHz SAW Filter SM13365-12 Case 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions Dimension A B C D E H P Min 13.08 6.27 Materials Max 13.60 6.80 2.00 Inches Nom 0.524 0.256 0.075 0.059 0.031 0.039 0.100 Min 0.515 0.247 Max 0.535 0.268 0.079 Electrical Connections Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body mm Nom 13.31 6.50 1.91 1.50 0.79 1.0 2.54 Connection Port 1 Port 2 Al2O3 Ceramic Terminals Input or Return 2 Return or Input 3 Output or Return 8 Return or Output Pb Free 9 Ground All others Single Ended Operation Return is ground Differential Operation B 3 Return is hot C 4 D H 2 1 2 3 4 1 P (8 Places) 5 12 12 5 6 11 11 6 7 10 10 7 A 8 9 TOP VIEW RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 9 E (10 Places) 8 BOTTOM VIEW E-mail: [email protected] http://www.rfm.com PX1002 112904