MILITARY DATA SHEET Original Creation Date: 10/30/95 Last Update Date: 08/28/96 Last Major Revision Date: 08/21/96 MN100314-X REV 1A0 LOW POWER QUINT DIFFERENTIAL LINE RECEIVER General Description The 100314 is a monolithic quint differential line receiver with emitter-follower outputs. An internal reference supply (Vbb) is available for single-ended reception. When used in single-ended operation, the only mode allowed is to connect the complementary inputs to Vbb. Unlike other F100K ECL devices, the inputs do not have input pull-down resistors. Active current sources provide common-mode rejection of 1.0V in either the positive or negative direction. A defined output state exists if both inverting and non-inverting inputs are at the same potential between Vee and Vcc. The defined state is logic HIGH on the Oa-Oe outputs. Industry Part Number NS Part Numbers 100314 100314DMQB 100314FMQB 100314J-QMLV 100314W-QMLV Prime Die F314 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MILITARY DATA SHEET MN100314-X REV 1A0 Features - 35% power reduction of the F100114 2000V ESD protection Pin/function compatible with 100114 Voltage compensated operating range = -4.2V to -5.7V Available to MIL-STD-883 Available to industrial grade temperature range 2 MILITARY DATA SHEET MN100314-X REV 1A0 (Absolute Maximum Ratings) (Note 1) Storage Temperature (Tstg) -65 C to +150 C Maximum Junction Temperature (Tj) Ceramic Plastic Vee Pin Potential to Ground Pin +175 C +150 C -7.0V to +0.5V Input Voltage (DC) Vee to +0.5V Output Current (DC Output HIGH) -50mA ESD (Note 2) > 2000V Note 1: Note 2: Absolute maximum ratings are those values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. ESD testing conforms to MIL-STD-883, Method 3015. Recommended Operating Conditions Case Temperature (Tc) Commercial Military Industrial Supply Voltage (Vee) 0 C to +85 C -55 C to +125 C -40 C to +85 C -5.7V to -4.2V 3 MILITARY DATA SHEET MN100314-X REV 1A0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vee Range: -4.2V to -5.7V, Tc= -55C to +125C, VCC=VCCA=GND SYMBOL IIH PARAMETER Input HIGH Current CONDITIONS NOTES Vee= -5.7V, VM= -0.87V PINNAME MIN MAX UNIT SUBGROUPS 1, 3 INPUTS 50 uA 1, 2 1, 3 INPUTS 70 uA 3 uA 1, 2, 3 ICBO Input Leakage Current Vee= -4.2V, VM= -4.2V 1, 3 INPUTS VOH Output HIGH Voltage Vee=-4.2V/-5.7V, VIH=-0.87V, VIL=-1.83V, LOADING: 50 Ohms To -2.0V 1, 3 OUTPUTS -1025 -870 mV 1, 2 1, 3 OUTPUTS -1085 -870 mV 3 1, 3 OUTPUTS -1830 -1620 mV 1, 2 1, 3 OUTPUTS -1830 -1555 mV 3 1, 3 OUTPUTS -1035 mV 1, 2 1, 3 OUTPUTS -1085 mV 3 VOL VOHC VOLC Output LOW Voltage Output HIGH Voltage Output LOW Voltage Vee=-4.2V/-5.7V, VIH=-0.87V, VIL=-1.83V, LOADING: 50 Ohms to -2.0V Vee=-4.2V/-5.7V, VIH=-1.165V, VIL=-1.475V, LOADING: 50 Ohms to -2.0V Vee=-4.2V/-5.7V, VIH=-1.165V, VIL=-1.475V, LOADING:50 Ohms to -2.0V -10 1, 3 OUTPUTS -1610 mV 1, 2 1, 3 OUTPUTS -1555 mV 3 -1260 mV 1, 2, 3 VBBX Output Reference Voltage Vee=-4.2V, IM=0uA 1, 3 VBB VBBN Output Reference Voltage Vee=-5.7V, IM=-250uA 1, 3 VBB -1380 mV 1, 2 Vee=-5.7V, IM=-350uA 1, 3 VBB -1396 mV 3 VIH Input HIGH Voltage Dn AT VBB 1, Dn 3, 7 -1165 -870 mV 1, 2, 3 VIL Input LOW Voltage Dn AT VBB 1, Dn 3, 7 -1830 -1475 mV 1, 2, 3 VCM Common Mode Voltage VEE= -4.2/-5.7V 1, INPUTS 3, 7 -2000 -500 mV 1, 2, 3 VDIFF Input Voltage Differential VEE= -4.2/-5.7V 1, INPUTS 3, 7 150 mV 1, 2, 3 IEE Power Supply Current Vee= -4.2/-5.7V, VIN=VBB 1, 3 VEE -65 mA 1, 2, 3 4 -25 MILITARY DATA SHEET MN100314-X REV 1A0 Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vee Range: -4.2V to -5.7V, VCC=VCCA=GND, LOADING: 50 Ohms To -2.0V SYMBOL PARAMETER tPLH/tPHL tTLH/tTHL Propagation Delay Transition Time Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: CONDITIONS NOTES Vee= -4.2/-5.7V Vee= -4.2/-5.7V PINNAME MIN MAX UNIT 2, 4 Dn/Dn t 0.6 o On/On 2.2 ns 9 2, 4 Dn/Dn t 0.6 o On/On 2.7 ns 10 2, 4 Dn/Dn t 0.4 o On/On 2.3 ns 11 6 1.4 ns 9, 10, 11 On/On 0.2 Screen tested 100% on each device at -55 C, +25 C and +125 C temp., subgroups 1, 2, 3, 7 & 8. For QB devices, screen tested 100% on each device at +25C temperature only, subgroup A9. For QMLV devices, screen tested 100% on each device at +25C, +125C & -55C temperature, subgroups A9, 10 & 11. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, +125 C & -55 C temp., subgroups A1, 2, 3, 7 & 8. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, subgroup A9, and at +125 C & -55 C temp., subgroups A10 & 11. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C temp. only, subgroup A9. Not tested at +25 C, +125 C & -55 C temp. (DESIGN CHARACTERIZATION DATA). Guaranteed by applying specified input condition and testing VOH/VOL. 5 SUBGROUPS MILITARY DATA SHEET MN100314-X REV 1A0 Graphics and Diagrams GRAPHICS# DESCRIPTION J24ERJ CERDIP(J), 24LD .400 CENTERS (P/P DWG) P000043A CERDIP (J), 24LD .400 CENTERS (PIN OUT) P000044A CERPAC, QUAD, 24 LEAD (PIN OUT) W24BRE CERPAC, QUAD, 24 LEAD (P/P DWG) See attached graphics following this page. 6