MwT-0820S-4N2/0820Z-4N2 8.0-20.0 GHz Balanced Amplifier Module www.mwtinc.com Email: [email protected] TYPICAL SPECIFICATIONS AT 25 C 14.0 dBm P-1dB 6.5 dB SMALL SIGNAL GAIN 15.0 dB RETURN LOSS 40 mA @ +8V USES TWO MwT-4 GaAs FET DEVICES 5.0 dB NOISE FIGURE Typical Noise Figure (dB) Typical Small Signal Gain (dB) 7.0 8.0 7.0 6.0 8 14 Frequency (GHz) SYMBOL FREQ SSG G/ F G/ T P-1dB PSAT P/ T IP3 2nd HAR 2nd HAR NF VSWR IN VSWR OUT ISO VDD IDD RTH 5.0 4.0 3.0 20 ELECTRICAL SPECIFICATIONS 6.0 8 14 Frequency (GHz) 20 (Ta=25 C) PARAMETERS Frequency Range Small Signal Gain SSG Flatness SSG Variation over Temperature Output Power at 1dB Compression Output Power at 6 dB Compression P-1dB Variation over Temperature Third Order Intercept Point 2nd Harmonic at Pout=14.0 dBm 2nd Harmonic at Pout=16.0 dBm Noise Figure Input VSWR Output VSWR Reverse Isolation Power Supply Voltage Small Signal Module Current Thermal Resistance Including FET* UNITS GHz dB +/-dB dB/ C dBm dBm dB/ C dBm dBc dBc dB --------dB +V mA C/W MIN 8.0 6.0 11.0 7.9 TYP MAX 20.0 6.5 0.4 -.012 14.0 16.0 -.008 25.0 -21.0 -16.0 4.5 1.5:1 1.5:1 -20.0 8.0 40.0 216.0 * When calculating Tch, use FET Vds = 4.0 volts and FET ds = 20 mA 4268 Solar Way Fremont California 94538 Phone: (510) 651-6700 Fax: (510) 651-2208 651-2208 All rights reserved. MicroWave Technology, Inc. All specifications subject to change without notice. 0.6 5.5 1.7:1 1.7:1 8.1 60.0 MwT-0820S-4N2/0820Z-4N2 8.0-20.0 GHz Balanced Amplifier Module DC O .110 .246 .025 DC O .095 RF OUT .158 .088 O .062 .246 .158 .088 .062 O .184 Email: [email protected] .184 www.mwtinc.com .095 .110 .041 RF IN .08 .08 .08 .08 RF IN RF OUT .390 .405 .500 DC “S” .405 .500 “Z” Configurations Construction: Construction .390 .055 Max. w/Caps & Bond Wires DC 1. Dimension in Inches 2. Tolerance: XXX= +/- .005 XX= +/- .01 The 15 mil alumina substrates and 10 mil copper FET ridge are brazed onto the 25 mil carrier using AuGe preform. The GaAs FETs are attached to the Cu ridge using AuSn preform. All capacitors are attached using AuSn preforms. The flanges are designed to accommodate 0-80 UNF-2A socket or Fillister head screws on .400 center-to-center hole spacing. The modules are mechanically and electrically designed to be cascaded. Notes: 1. Custom module specifications and/or custom module mechanical configurations are available. 2. Operating Temperature Range is -55 degrees Celsius to +105 degrees Celsius. 3. All modules are serialized and shipped with data measured at 25 degrees Celsius. Data includes swept small signal gain, swept input and output return loss. Noise figure and P-1dB are measured in 1 GHz increments. Special module testing is available. 4. Test Fixtures are available. 5. Microwave Technology reserves the right to ship modules with performance above the typical specifications. 4268 Solar Way Fremont California 94538 Phone: (510) 651-6700 Fax: (510) 651-2208 651-2208 All rights reserved. MicroWave Technology, Inc. All specifications subject to change without notice.