TS1871 TS1872 TS1874 1.8V INPUT/OUTPUT RAIL TO RAIL LOW POWER OPERATIONAL AMPLIFIERS ■ OPERATING AT VCC = 1.8V to 6V ■ RAIL TO RAIL INPUT & OUTPUT ■ EXTENDED Vicm (VDD - 0.2V to VCC + 0.2V) ■ LOW SUPPLY CURRENT (400µA) ■ GAIN BANDWIDTH PRODUCT (1.6MHz) ■ HIGH STABILITY ■ ESD TOLERANCE (2kV) ■ LATCH-UP IMMUNITY ■ AVAILABLE IN SOT23-5 MICROPACKAGE PIN CONNECTIONS (top view) TS1871ILT Output 1 VDD 2 Non Inverting Input 3 5 VCC 4 Inverting Input + - DESCRIPTION The TS187x (Single, Dual & Quad) is operational amplifier able to operate with voltages as low as 1.8V and features both I/O Rail to Rail. The common mode input voltage extends 200mV @ 25°C beyond the supply voltages while the output voltage swing is within 100mV of each Rail for a 600 Ohm load resistor. This I/O Rail to Rail configuration gives the chance to the user to have the entire supply voltage range available. Offering 20mA min., 65mA typ. value and exhibiting an excellent speed-power ratio, 1.6MHz GBP & 400µA supply current, this Op-Amp is very well-suited for battery-supplied and portable applications. Stability and minimum overshoot with capacitive loads is maintained by 53° typ. of phase margin with 100pF load capacitor @ 1.8V. APPLICATION ■ Battery-powered applications (Toys) ■ Portable communication devices (cell phone) ■ Audio driver (Headphone Driver) ■ Laptop/Notebook computers TS1871ID-TS1871IDT N.C. 1 Inverting Input 8 N.C. 2 _ 7 VCC Non Inverting Input 3 + 6 Output VDD 4 5 N.C. TS1872IN-TS1872ID-TS1872IDT-TS1872IPT Output1 1 8 VCC InvertingInput 1 2 _ NonInvertingInput 1 3 + 7 Output 2 _ 6 InvertingInput 2 + 5 NonInvertingInput 2 VDD 4 TS1874IN-TS1874ID-TS1874IDT-TS1874IPT ORDER CODE Part Number TS1871I/AI TS1872I/AI TS1874I/AI Temperature Range -40, +125°C Package N D • • • • • P L • SOT23 Marking K161/K162 • • N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT) L = Tiny Package (SOT23-5) - only available in Tape & Reel (LT) August 2001 14 Output 4 Output1 1 Inverting Input1 2 _ _ 13 Inverting Input 4 Non Inverting Input 1 3 + + 12 Non InvertingInput 4 VCC 4 Non Inverting Input 2 5 Inverting Input 2 6 Output 2 7 11 VDD + _ + 10 NonInverting Input 3 _ 9 Inverting Input 3 8 Output 3 1/20 TS1871-TS1872-TS1874 ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Supply voltage 1) Differential Input Voltage 2) 3) Value Unit 7 V ±1 V -0.3 to VCC +0.3 V Toper Operating Free Air Temperature Range -40 to + 125 °C Tstg Storage Temperature -65 to +150 °C 150 °C Tj R thja ESD 1. 2. 3. 4. Parameter Input Voltage Maximum Junction Temperature °C/W 4) Thermal Resistance Junction to Ambient SOT23-5 SO8 SO14 TSSOP8 TSSOP14 Human Body Model Latch-up Immunity Lead Temperature (soldering, 10sec) 250 175 150 200 175 2 Class A 260 kV °C All voltages values, except differential voltage are with respect to network terminal. Differential voltages are non-inverting input terminal with respect to the inverting input terminal. The magnitude of input and output voltages must never exceed VCC + 0.3V. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuit on all amplifiers OPERATING CONDITIONS Symbol VCC Vicm Vicm Parameter Supply Voltage Unit 1.8 to 6 V Common Mode Input Voltage Range 1) VDD - 0.2 to VCC + 0.2 V Common Mode Input Voltage Range 2) VDD to VCC V 1. At 25°C, for 1.8 ≤ VCC ≤ 6V, V icm is extended to VDD - 0.2V, VCC + 0.2V. 2. In full temperature range, both Rails can be reached when VCC does not exceed 5.5V. 2/20 Value TS1871-TS1872-TS1874 ELECTRICAL CHARACTERISTICS VCC = +1.8V, VDD = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. 0.1 3 1 Unit Input Offset Voltage Vio ∆Vio Iio Iib V icm = Vout = VCC /2 TS1871/2/4 TS1871A/2A/4A Input Offset Voltage Drift µV/°C 2 Input Offset Current 1) V icm = Vout = VCC /2 Input Bias Current 1) V icm = Vout = VCC /2 mV 3 28 nA 40 125 nA CMR Common Mode Rejection Ratio 0 ≤ Vicm ≤ VCC , Vout = VCC /2 55 77 SVR Supply Voltage Rejection Ratio 70 80 R L = 2kΩ R L = 600Ω 77 70 92 85 R L = 2kΩ R L = 600Ω 1.65 1.62 1.77 1.74 dB dB Large Signal Voltage Gain Avd V out = 0.5V to 1.3V dB High Level Output Voltage VOH V id = 100mV V Low Level Output Voltage VOL Io ICC V id = -100mV R L = 2kΩ R L = 600Ω Output Source Current V ID = 100mV, VO = VDD Output Sink Current V ID = -100mV, V O = VCC 88 115 20 65 20 65 Supply Current (per amplifier) A VCL = 1, no load 400 100 150 mV mA 560 µA Gain Bandwith Product RL = 10kΩ, C L = 100pF, f = 100kHz 0.9 1.6 MHz SR Slew Rate RL = 10kΩ, C L = 100pF, AV = 1 0.38 0.54 V/µs φm Phase Margin CL = 100pF 53 Degrees en Input Voltage Noise 27 nV/√Hz 0.01 % GBP THD Total Harmonic Distortion 1. Maximum values including unavoidable inaccuracies of the industrial test. 3/20 TS1871-TS1872-TS1874 ELECTRICAL CHARACTERISTICS VCC = +3V, VDD = 0V, RL, CL connected to VCC/2, T amb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. 0.1 3 1 Unit Input Offset Voltage Vio ∆Vio Iio Iib V icm = Vout = VCC /2 TS1871/2/4 TS1871A/2A/4A Input Offset Voltage Drift µV/°C 2 Input Offset Current 1) V icm = Vout = VCC /2 Input Bias Current 1) V icm = Vout = VCC /2 mV 3 28 nA 4 125 nA CMR Common Mode Rejection Ratio 0 ≤ Vicm ≤ VCC , Vout = VCC /2 60 80 SVR Supply Voltage Rejection Ratio 70 85 dB 80 74 92 95 dB 2.82 2.80 2.95 2.95 dB Large Signal Voltage Gain Avd V out = 0.5V to 2.5V R L = 2kΩ R L = 600Ω High Level Output Voltage VOH V id = 100mV R L = 2kΩ R L = 600Ω V Low Level Output Voltage VOL Io ICC V id = -100mV R L = 2kΩ R L = 600Ω Output Source Current V ID = 100mV, VO = VDD Output Sink Current V ID = -100mV, V O = VCC SR Slew Rate RL = 10kΩ, C L = 100pF, AV = 1 φm Phase Margin CL = 100pF en Input Voltage Noise Total Harmonic Distortion 1. Maximum values including unavoidable inaccuracies of the industrial test. 4/20 80 20 80 450 RL = 10kΩ, C L = 100pF, f = 100kHz THD 20 Supply Current (per amplifier) A VCL = 1, no load Gain Bandwith Product GBP 88 115 120 160 mV mA 650 µA 1 1.7 MHz 0.42 0.6 V/µs 53 Degrees 40 nV/√Hz 0.01 % TS1871-TS1872-TS1874 ELECTRICAL CHARACTERISTICS VCC = +5V, VDD = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. 0.1 3 1 Unit Input Offset Voltage Vio ∆Vio Iio Iib CMR SVR V icm = Vout = VCC /2 TS1871/2/4 TS1871A/2A/4A Input Offset Voltage Drift µV/°C 2 Input Offset Current 1) V icm = Vout = VCC /2 Input Bias Current 1) V icm = Vout = VCC /2 Common Mode Rejection Ratio mV 3 30 nA 68 130 nA 65 85 dB 70 90 dB R L = 2kΩ R L = 600Ω 83 77 92 85 R L = 2kΩ R L = 600Ω 4.80 4.75 4.95 4.90 0 ≤ Vicm ≤ VCC , Vout different of VCC /2 Supply Voltage Rejection Ratio Large Signal Voltage Gain Avd V out = 1V to 4V dB High Level Output Voltage VOH V id = 100mV V Low Level Output Voltage VOL Io ICC V id = -100mV R L = 2kΩ R L = 600Ω Output Source Current V ID = 100mV, VO = VDD Output Sink Current V ID = -100mV, V O = VCC 80 20 80 513 RL = 10kΩ, C L = 100pF, f = 100kHz SR Slew Rate RL = 10kΩ, C L = 100pF, AV = 1 φm Phase Margin CL = 100pF en Input Voltage Noise THD 20 Supply Current (per amplifier) A VCL = 1, no load Gain Bandwith Product GBP 88 115 Total Harmonic Distortion 130 188 mV mA 835 µA 1 1.8 MHz 0.42 0.6 V/µs 55 Degrees 40 nV/√Hz 0.01 % 1. Maximum values including unavoidable inaccuracies of the industrial test. 5/20 TS1871-TS1872-TS1874 Input Offset Voltage Distribution Input Offset Voltage Drift vs. Temperature 200 160 Vcc = 1.8V 492 pieces tested Vcc = 5V Temp = +25°C 120 150 Input Voltage Drift (µV) Quantity of pieces 140 100 80 60 100 Vcc = 3V 50 Vcc = 5V 0 -50 40 -100 20 -150 -40 0 -2. -1.6 -1.2 -.8 -.4 0 .4 .8 1.2 1.6 -20 0 2 20 40 60 80 100 120 140 Temperature(°C) Input Offset Voltage (mV) Input Bias Current vs. Temperature Input Bias Current vs. Temperature 10.0 10.0 Vcc = 3V Vicm = 1.5V Vcc = 1.8V Vicm = 0.9V Input bias current (nA) Input bias current (nA) 0.0 -10.0 -20.0 -30.0 0.0 -10.0 -20.0 -30.0 -40.0 -40 -20 0 20 40 60 80 100 120 -40.0 -40 -20 140 0 20 Temperature (°C) Supply Current / Amplifier vs. Supply Voltage 40 60 80 100 Temperature (°C) 120 140 Supply Current / Amplifier vs. Temperature 600 550 500 500 Supply Current (µA) Supply Current (µA) Vcc = 5V 400 Tamb = 25°C 300 200 400 Vcc = 1.8V 350 300 100 0 0 6/20 Vcc = 3V 450 2 4 Supply Voltage (V) 6 8 250 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 140 TS1871-TS1872-TS1874 Common Mode Rejection vs. Temperature Supply Voltage Rejection vs. Temperature 110 Vcc = 1.8V Vicm = 0V 115 Supply Voltage Rejection (dB) Common Mode Rejection (dB) 120 110 Vcc = 3V Vicm = 0V 105 100 Vcc = 5V Vicm = 0V 95 90 85 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 Vcc = 1.8V Vicm = 0V 100 90 80 70 60 -40 140 0 20 Supply Voltage Rejection vs. Temperature 60 80 100 120 140 Supply Voltage Rejection vs. Temperature 110 Supply Voltage Rejection (dB) Vcc = 3V Vicm = 0V 100 90 80 70 60 -40 Vcc = 5V Vicm = 0V 100 90 80 70 60 -20 0 20 40 60 80 100 120 140 -40 -20 0 20 Power Supply Voltage Rejection vs. Frequency 60 80 100 120 140 Open Loop Gain vs. Temperature -20 110 Vcc = 1.8V Vicm = 0.9V Vcc = 1.8V Vicm = 0.7V Gain = 10 Open Loop Gain (dB) -30 40 Temperature (°C) Temperature (°C) Supply Voltage Rejection (dB) 40 Temperature (°C) 110 Supply Voltage Rejection (dB) -20 -40 -50 -60 100 RL = 2 kOhms 90 RL = 600 Ohms 80 -70 -80 100 1000 10000 Frequency(Hz) 100000 70 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 140 7/20 TS1871-TS1872-TS1874 Open Loop Gain vs. Temperature Open Loop Gain vs. Temperature 110 110 100 90 RL = 600 Ohms 80 70 -40 RL = 2 kOhms Vcc = 5V Vicm = 2.5V RL = 2 kOhms Open Loop Gain (dB) Open Loop Gain (dB) Vcc = 3V Vicm = 1.5V 100 90 RL = 600 ohms 80 70 -20 0 20 40 60 80 100 120 140 -40 -20 0 20 Temperature(°C) High Level Output Voltage vs. Temperature RL = 600 ohms Vcc = 5V 100 Voltage Referenced to Gnd (mV) Voltage Referenced to VCC (mV) 80 100 120 140 Low Level Output Voltage vs. Temperature 90 80 Vcc = 3V 70 Vcc = 1.8V 60 50 -40 -20 0 20 40 60 80 100 120 RL = 600 ohms 100 90 140 Vcc = 5V 80 Vcc = 3V 70 60 Vcc = 1.8V 50 40 -40 40 -20 0 20 40 60 80 100 120 140 Temperature (°C) Temperature (°C) Low Level Output Voltage vs. Temperature High Level Output Voltage vs. Temperature 80 80 RL = 2 kohms Voltage Referenced to Gnd (mV) Voltage Referenced to VCC (mV) 60 110 110 70 Vcc = 5V 60 50 Vcc = 3V 40 Vcc = 1.8V 30 20 -40 -20 0 20 40 60 Temperature (°C) 8/20 40 Temperature (°C) 80 100 120 140 RL = 2 kohms 70 60 50 Vcc = 5V 40 Vcc = 3V Vcc = 1.8V 30 20 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 140 TS1871-TS1872-TS1874 Output Current vs. Temperature Output Current vs. Temperature 100 100 Isink 50 Output Current (mA) Output Current (mA) Isink Vcc = 1.8V Vid = 1V 0 Isource Vcc = 3V Vid = 1V 0 Isource -50 -50 -100 -40 50 -20 0 20 40 60 80 100 120 -100 -40 140 -20 0 20 Temperature (°C) 40 60 80 100 120 140 Temperature (°C) Output Current vs. Temperature Output Current vs. Temperature 100 100 T = 25 °C T = -40 °C 50 Output Current (mA) Output Current (mA) Isink Vcc = 5V Vid = 1V 0 Isource -50 sink T = 125 °C 50 Vcc = 1.8V Vid = 0.1V Vicm = 0.9V 0 T = -40 °C -50 T = 125 °C T = 25 °C source -100 -40 -100 -20 0 20 40 60 80 100 120 0.0 140 0.5 1.0 2.0 Output Current vs. Temperature Output Current vs. Temperature 100 100 T = -40 °C sink 50 T = 125 °C Vcc = 3V Vid = 0.1V Vicm = 1.5V 0 T = 125 °C T = 25 °C -50 T = -40 °C 0.5 sink 50 Vcc = 5V Vid = 0.1V Vicm = 2.5V 0 T = 125 °C T = 25 °C T = -40 °C source 1.0 1.5 2.0 Output Voltage (V) 2.5 3.0 T = 25 °C T = 125 °C -50 -100 0.0 T = -40 °C T = 25 °C Output Current (mA) Output Current (mA) 1.5 Output Voltage (V) Temperature (°C) 3.5 source -100 0.0 1.0 2.0 3.0 4.0 5.0 Output Voltage (V) 9/20 TS1871-TS1872-TS1874 Gain and Phase vs. Frequency Gain and Phase vs. Frequency 70 180 60 140 50 120 gain phase 30 100 180 RL = 10K CL = 100 pF Vcc = 3V 160 140 120 40 gain 30 phase 100 20 80 20 80 10 60 10 60 0 1E+3 40 1E+4 1E+5 Frequency (Hz) 40 0 1E+3 1E+6 Phase (°) 40 60 Phase (°) Gain (dB) 50 160 Gain (dB) RL = 10K CL = 100 pF Vcc = 1.8V 70 1E+4 1E+5 Frequency (Hz) 1E+6 Gain-Bandwidth Product vs. Temperature Gain and Phase vs. Frequency Vcc = 5V RL = 10K CL = 100 pF Vcc = 5V 60 50 160 140 gain phase 30 100 20 80 10 60 0 1E+3 Phase (°) 120 40 Gain-Bandwidth Product (MHz) 180 70 Gain (dB) 1.70 1E+5 1E+6 Vcc = 3V 1.50 Vcc = 1.8V 1.40 1.30 1.20 -40 40 1E+4 1.60 Vicm = Vcc/2 RL = 10kohms CL = 100 pF -20 0 20 Frequency (Hz) Gain-Bandwidth Product vs. Supply Voltage 80 100 120 140 Slew Rate vs. Temperature 0.50 Slew Rate (V/µs) Gain-Bandwidth Product (MHz) 60 0.55 2.0 1.5 RL = 2 kohms CL = 220 pF Vicm = Vcc/2 T = 25°C 1.0 Vcc = 1.8V gain = +1 Vin = 0.4 to 1.4V RL = 10kohms CL = 100 pF negative Slew Rate positive Slew Rate 0.45 0.40 0.35 0.5 1 10/20 40 Temperature (°C) 2 3 4 Supply Voltage (V) 5 0.30 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 140 TS1871-TS1872-TS1874 Slew Rate vs. Temperature 0.70 0.60 positive Slew Rate Vcc = 3V gain = +1 Vin = 1 to 2V RL = 10kohms CL = 100 pF 0.70 Slew Rate (V/µs) Slew Rate (V/µs) 0.65 Slew Rate vs. Temperature 0.75 negative Slew Rate 0.55 0.50 0.45 positive Slew Rate negative Slew Rate 0.60 0.55 0.50 0.45 0.40 0.35 -40 0.65 Vcc = 5V gain = +1 Vin = 2 to 3V RL = 10kohms CL = 100 pF 0.40 -20 0 20 40 60 80 100 120 0.35 -40 140 -20 0 20 Temperature (°C) Phase Margin vs. Load Capacitor Vcc = 1.8V gain = 40dB RL = 1Kohms 100 120 140 75 40 Phase Margin (°) Phase Margin (°) 80 80 30 20 10 70 Vcc = 1.8V RL = 1 kOhms CL = 220 pF 65 60 55 50 0 45 -10 40 10 100 Load Capacitor (pF) 1000 -10 Equivalent Input Noise (nV/sqr(Hz)) Vcc = 1.8V RL = 1 kOhms CL = 220 pF -15 -20 -5 0 5 DC Output Curre nt (mA) 5 10 35 -5 -25 -10 0 Equivalent Input Noise vs. Frequency Gain Margin vs. Output Current -10 -5 DC Output Current (mA) 0 Gain Margin (dB) 60 Phase Margin vs. Output Current 60 50 40 Temperature (°C) 10 30 25 20 15 10 5 1E+1 Vcc = 1.8V gain = 100 Rs = 100 ohms 1E+2 1E+3 1E+4 1E+5 Frequency (Hz) 11/20 TS1871-TS1872-TS1874 Distortion vs. Output Voltage Distortion vs. Output Voltage 100.000 RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 1.8V 10.000 Distortion (%) Distortion (%) 10.000 100.000 1.000 0.100 0.010 0.001 0.00 RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 3V 1.000 0.100 0.010 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.001 0.00 0080 0.20 Output Voltage (VRMS) Distortion vs. Output Voltage 10.000 Distortion (%) Distortion (%) RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 5V 0.100 0.010 0.50 1.00 1.50 1.000 0.100 0.001 0.00 2.00 0.20 0.60 0.80 1.00 1.20 Distortion vs. Output Voltage 100.000 RL= 1500 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V 10.000 Distortion (%) Distortion (%) 0.40 Output Voltage (VRMS) Distortion vs. Output Voltage 1.000 0.100 0.010 RL= 4700 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V 1.000 0.100 0.010 0.20 0.40 0.60 0.80 Output Voltage (VRMS) 12/20 1.20 0.010 100.000 0.001 0.00 1.00 RL= 150 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V Output Voltage (VRMS) 10.000 0.80 100.000 1.000 0.001 0.00 0.60 Distortion vs. Output Voltage 100.000 10.000 0.40 Output Voltage (VRMS) 1.00 1.20 0.001 0.00 0.20 0.,40 0.60 0.80 Output Voltage (VRMS) 1.00 1.20 TS1871-TS1872-TS1874 Distortion vs. Frequency Distortion vs. Frequency Distortion (%) 0.012 Vcc = 1.8V Vout = 1Vpp RL = 1Kohms gain = -1 0.013 Distortion (%) 0.014 0.015 0.010 0.008 Vcc = 3V Vout = 1Vpp RL = 1Kohms gain = -1 0.010 0.007 0.005 0.003 0.006 0,004. 1E+1 1E+2 1E+3 1E+4 0.000 1E+1 1E+5 1E+2 Frequency (Hz) 1E+5 0.150 Vcc = 1.8V Vout = 1Vpp RL = 32 ohms gain = -1 0.125 Distortion (%) Distortion (%) 1E+4 Distortion vs. Frequency Distortion vs. Frequency 0.150 0.125 1E+3 Frequency (Hz) 0.100 0.075 0.050 Vcc = 3V Vout = 1Vpp RL = 32 ohms gain = -1 0.100 0.075 0.050 0.025 0.025 0.000 1E+1 1E+2 1E+3 1E+4 1E+5 0.000 1E+1 1E+2 1E+3 1E+4 1E+5 Frequency (Hz) Frequency (Hz) Output Power vs. Supply Voltage 60 RL = 32 ohms 10% distortion Output Power (mW) 50 1% distortion 40 30 0.1% distortion 20 10 0 1 2 3 4 5 6 Supply Voltage (V) 13/20 TS1871-TS1872-TS1874 TS1872IN PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. A a1 B b b1 D E e e3 e4 F i L Z 14/20 Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 9.75 7.95 0.020 0.045 0.014 0.008 Max. 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Typ. 0.131 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 TS1871-TS1872-TS1874 TS1871ID - TS1872ID PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Millimeters Inches Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45° (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 8° (max.) 15/20 TS1871-TS1872-TS1874 TS1872IPT PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE k 0,25 mm .010 inch GAGE PLANE C PLANE SEATING E1 L1 L c A A2 E e aaa 1 8 C b D 5 4 A1 PIN 1 IDENTIFICATION Millimeters Inches Dim. Min. A A1 A2 b c D E E1 e k l 16/20 0.05 0.80 0.19 0.09 2.90 4.30 0° 0.50 Typ. 1.00 3.00 6.40 4.40 0.65 0.60 Max. Min. 1.20 0.15 1.05 0.30 0.20 3.10 0.01 0.031 0.007 0.003 0.114 4.50 0.169 8° 0.75 0° 0.09 Typ. 0.039 0.118 0.252 0.173 0.025 0.0236 Max. 0.05 0.006 0.041 0.15 0.012 0.122 0.177 8° 0.030 TS1871-TS1872-TS1874 TS1874IN PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. a1 B b b1 D E e e3 F i L Z Typ. 0.51 1.39 Max. Min. 1.65 0.020 0.055 0.5 0.25 Typ. 0.065 0.020 0.010 20 0.787 8.5 2.54 15.24 0.335 0.100 0.600 7.1 5.1 0.280 0.201 3.3 1.27 Max. 0.130 2.54 0.050 0.100 17/20 TS1871-TS1872-TS1874 TS1874ID PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) G c1 s e3 D E b1 e a1 b A a2 C L M 8 1 7 F 14 Millimeters Inches Dim. Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S Typ. Max. Min. 1.75 0.2 1.6 0.46 0.25 0.1 0.35 0.19 Typ. 0.004 0.014 0.007 0.5 Max. 0.069 0.008 0.063 0.018 0.010 0.020 45° (typ.) 8.55 5.8 8.75 6.2 0.336 0.228 1.27 7.62 3.8 4.6 0.5 0.344 0.244 0.050 0.300 4.0 5.3 1.27 0.68 0.150 0.181 0.020 0.157 0.208 0.050 0.027 8° (max.) Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK. 18/20 TS1871-TS1872-TS1874 TS1874IPT PACKAGE MECHANICAL DATA 14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE k E1 L1 L c E A A2 D e b A1 Millimeters Inches Dim. Min. A A1 A2 b c D E E1 e k l 0.05 0.80 0.19 0.09 4.90 4.30 0° 0.50 Typ. 1.00 5.00 6.40 4.40 0.65 0.60 Max. Min. 1.20 0.15 1.05 0.30 0.20 5.10 0.01 0.031 0.007 0.003 0.192 4.50 0.169 8° 0.75 0° 0.09 Typ. 0.039 0.196 0.252 0.173 0.025 0.0236 Max. 0.05 0.006 0.041 0.15 0.012 0.20 0.177 8° 0.030 19/20 TS1871-TS1872-TS1874 TS1871ILT PACKAGE MECHANICAL DATA 5 PINS - TINY PACKAGE (SOT23) A E A2 D b A1 L C E1 Millimeters Inches Dim. A A1 A2 B C D D1 e E F L K Min. Typ. Max. Min. Typ. Max. 0.90 0 0.90 0.35 0.09 2.80 1.20 1.45 0.15 1.30 0.50 0.20 3.00 0.035 0.047 0.035 0.014 0.004 0.110 3.00 1.75 0.60 10d 0.102 0.059 0.004 0d 0.041 0.016 0.006 0.114 0.075 0.037 0.110 0.063 0.014 0.057 0.006 0.051 0.020 0.008 0.118 2.60 1.50 0.10 0d 1.05 0.40 0.15 2.90 1.90 0.95 2.80 1.60 0.5 0.0118 0.069 0.024 10d Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibil ity for the consequences of use of such information nor for any infring ement of patents or other righ ts of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change witho ut notice. This publ ication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life suppo rt devices or systems withou t express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom http://www. st.com 20/20