STMICROELECTRONICS TS1874IPT

TS1871-TS1872-TS1874
1.8V input/output rail-to-rail
low power operational amplifiers
Features
■
Operating range from VCC = 1.8V to 6V
■
Rail-to-rail input and output
■
Extended Vicm (VDD - 0.2V to VCC + 0.2V)
■
Low supply current (400µA)
■
Gain bandwidth product (1.6MHz)
■
High unity gain stability
■
ESD tolerance (2kV)
■
Latch-up immunity
■
Available in SOT23-5 micro package
TS1871ILT
Battery-powered applications (toys)
■
Portable communication devices (cell phones)
■
Audio driver (headphone drivers)
■
Laptop/notebook computers
Description
VDD
2
Non Inverting Input
3
5
VCC
4
Inverting Input
N.C.
1
Inverting Input
2
Non Inverting Input
3
VDD
4
8
N.C.
_
7
VCC
+
6
Output
5
N.C.
TS1872IN-TS1872ID/IDT-TS1872IST
TS1872IPT
Output 1
1
Inverting Input 1
2
_
Non Inverting Input 1
3
+
The TS187x (single, dual and quad) is an
operational amplifier family able to operate with
voltages as low as 1.8V and that features both
input and output rail-to-rail.
VDD
4
8
VCC
7
Output 2
_
6
Inverting Input 2
+
5
Non Inverting Input 2
TS1874IN-TS1874ID/IDT-TS1874IPT
The common mode input voltage extends 200mV
beyond the supply voltages at 25°C while the
output voltage swing is within 100mV of each rail
with a 600Ω load resistor. This device consumes
typically 400µA per channel while offering 1.6MHz
of gain-bandwidth product. The amplifier provides
high output drive capability typically at 65mA load.
Output 1
These features make the TS187x family ideal for
sensor interface, battery-supplied and portable
applications.
January 2008
1
TS1871ID/IDT
Applications
■
Output
Rev 4
14 Output 4
1
Inverting Input 1
2
_
Non Inverting Input 1
3
+
VCC
4
Non Inverting Input 2
5
Inverting Input 2
6
Output 2
7
_
13 Inverting Input 4
+
12 Non Inverting Input 4
11 VDD
+
_
+
_
10 Non Inverting Input 3
9
Inverting Input 3
8
Output 3
1/26
www.st.com
26
Contents
TS1871-TS1872-TS1874
Contents
1
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3
2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1
SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2
DIP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3
SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4
TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.5
MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.6
DIP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.7
SO-14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.8
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2/26
TS1871-TS1872-TS1874
Absolute maximum ratings and operating conditions
1
Absolute maximum ratings and operating conditions
Table 1.
Absolute maximum ratings
Symbol
VCC
Parameter
Supply voltage(1)
Vid
Differential input voltage
Vin
Input voltage
Tstg
Storage temperature
Tj
(2)
Maximum junction temperature
Value
Unit
7
V
±1
V
VDD -0.3 to VCC +0.3
V
-65 to +150
°C
150
°C
(3)
Rthja
Thermal resistance junction to ambient
SOT23-5
DIP8
DIP14
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
Rthjc
Thermal resistance junction to case
SOT23-5
DIP8
DIP14
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
81
41
33
39
40
31
37
32
2
200
1.5
kV
ESD
HBM: human body model(4)
MM: machine model(5)
CDM: charged device model(6)
Latch-up immunity
200
mA
Lead temperature (soldering, 10 sec)
250
Output short-circuit duration
250
85
66
190
125
103
120
100
see note
°C/W
°C/W
V
kV
°C
(7)
1. All voltage values, except differential voltage are with respect to network terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > ±1V, the
maximum input current must not exceed ±1mA. When Vid > ±1V, add an input series resistor to limit input current.
3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all
amplifiers.
4. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a 1.5kΩ resistor
between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
5. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
device with no external series resistor (internal resistor < 5Ω). This is done for all couples of connected pin combinations
while the other pins are floating.
6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly
to the ground through only one pin. This is done for all pins.
7. Short-circuits from the output to VCC can cause excessive heating. The maximum output current is approximately 80mA,
independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
3/26
Absolute maximum ratings and operating conditions
Table 2.
Operating conditions
Symbol
4/26
TS1871-TS1872-TS1874
Parameter
Value
Unit
1.8 to 6
V
VCC
Supply voltage
Vicm
Common mode input voltage range
Toper = 25°C, 1.8 ≤ VCC ≤ 6V
Tmin < Toper < Tmax, 1.8 ≤ VCC ≤ 6V
VDD - 0.2 to VCC + 0.2
VDD to VCC
V
Toper
Operating free air temperature range
-40 to + 125
°C
TS1871-TS1872-TS1874
Electrical characteristics
2
Electrical characteristics
Table 3.
Electrical characteristics at VCC = +1.8V
with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25°C (unless otherwise specified)(1)
Symbol
Vio
ΔVio
Parameter
Input offset voltage
Conditions
Min.
Vicm = Vout = VCC/2
TS1871A/2A/4A
Tmin ≤ Tamb ≤ Tmax
TS1871/2/4
Tmin ≤ Tamb ≤ Tmax
Typ.
0.1
Input offset voltage drift
Max.
1
1.5
3
6
2
(2)
Unit
mV
µV/°C
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
Iib
Input bias current
Vicm = Vout = VCC/2(1)
Tmin ≤ Tamb ≤ Tmax
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤ Vicm ≤ VCC, Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
55
52
77
Large signal voltage gain
Vout = 0.5V to 1.3V
RL = 2kΩ
RL = 600Ω
77
70
92
85
High level output voltage
Vid = 100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
1.65
1.62
1.65
1.62
1.77
1.74
Low level output voltage
Vid = -100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
Output source current
Vid = 100mV, VO = VDD
20
65
Output sink current
Vid = -100mV, VO = VCC
20
65
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
0.9
1.6
MHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
0.38
0.54
V/µs
φm
Phase margin
CL = 100pF
53
Degrees
en
Input voltage noise
f = 1kHz
27
nV/√Hz
0.01
%
CMR
Avd
VOH
VOL
Io
ICC
GBP
THD
Total harmonic distortion
3
30
60
nA
40
125
150
nA
88
115
dB
dB
V
100
150
100
150
mV
mA
400
560
600
µA
1. All parameter limits at temperatures different from 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
5/26
Electrical characteristics
Table 4.
Electrical characteristics at VCC = +3V
with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25°C (unless otherwise specified)(1)
Symbol
Vio
ΔVio
TS1871-TS1872-TS1874
Parameter
Input offset voltage
Conditions
Min.
Vicm = Vout = VCC/2
TS1871A/2A/4A
Tmin ≤ Tamb ≤ Tmax
TS1871/2/4
Tmin ≤ Tamb ≤ Tmax
Typ.
0.1
Input offset voltage drift
Max.
1
1.5
3
6
2
(2)
Unit
mV
µV/°C
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
Iib
Input bias current
Vicm = Vout = VCC/2 (1)
Tmin ≤ Tamb ≤ Tmax
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤ Vicm ≤ VCC, Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
60
57
80
dB
Large signal voltage gain
Vout = 0.5V to 2.5V
RL = 2kΩ
RL = 600Ω
80
74
92
95
dB
High level output voltage
Vid = 100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
2.82
2.80
2.82
2.80
2.95
2.95
Low level output voltage
Vid = -100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
Output source current
Vid = 100mV, VO = VDD
20
80
Output sink current
Vid = -100mV, VO = VCC
20
80
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
φm
Phase margin
en
Input voltage noise
CMR
Avd
VOH
VOL
Io
ICC
GBP
THD
30
60
nA
4
125
150
nA
88
115
V
120
160
120
160
mV
mA
450
650
690
µA
1
1.7
MHz
0.42
0.6
V/µs
CL = 100pF
53
Degrees
f = 1kHz
27
nV/√Hz
0.01
%
Total harmonic distortion
1. All parameter limits at temperatures different from 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
6/26
3
TS1871-TS1872-TS1874
Table 5.
Electrical characteristics at VCC = +5V
with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25°C (unless otherwise specified) (1)
Symbol
Vio
ΔVio
Electrical characteristics
Parameter
Input offset voltage
Conditions
Min.
Vicm = Vout = VCC/2
TS1871A/2A/4A
Tmin ≤ Tamb ≤ Tmax
TS1871/2/4
Tmin ≤ Tamb ≤ Tmax
Typ.
0.1
Input offset voltage drift
Max.
1
1.5
3
6
2
(2)
Unit
mV
µV/°C
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
Iib
Input bias current
Vicm = Vout = VCC/2 (1)
Tmin ≤ Tamb ≤ Tmax
CMR
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤ Vicm ≤ VCC, Vout not equal to VCC/2
Tmin ≤ Tamb ≤ Tmax
65
62
85
SVR
Supply voltage rejection ratio
20 log (ΔVcc/ΔVio)
VCC = 1.8 to 5V
70
90
dB
Avd
Large signal voltage gain
Vout = 1V to 4V
RL = 2kΩ
RL = 600Ω
83
77
92
85
dB
High level output voltage
Vid = 100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
4.80
4.75
4.80
4.75
4.95
4.90
Low level output voltage
Vid = -100mV
RL = 2kΩ
RL = 600Ω
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 600Ω
Output source current
Vid = 100mV, VO = VDD
20
80
Output sink current
Vid = -100mV, VO = VCC
20
80
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
φm
Phase margin
en
Input voltage noise
VOH
VOL
Io
ICC
GBP
THD
3
30
60
nA
70
130
150
nA
88
115
dB
V
130
188
130
188
mV
mA
500
835
875
µA
1
1.8
MHz
0.42
0.6
V/µs
CL = 100pF
55
Degrees
f = 1kHz
27
nV/√Hz
0.01
%
Total harmonic distortion
1. All parameter limits at temperatures different from 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
7/26
Electrical characteristics
Figure 1.
TS1871-TS1872-TS1874
Input offset voltage distribution
Figure 2.
160
200
Vcc = 1.8V
492 pieces tested
Vcc = 5V
Temp = +25°C
150
Input Offset voltage (µV)
140
Quantity of pieces
Input offset voltage vs. temperature
120
100
80
60
40
100
Vcc = 3V
50
Vcc = 5V
0
-50
-100
20
-150
-40
0
-2.
-1.6 -1.2 -.8
-.4
0
.4
.8
1.2
1.6
2
-20
0
40
60
80
Input bias current vs. temperature
Figure 4.
10.0
Vcc = 3V
Vicm = 1.5V
Input bias current (nA)
Input bias current (nA)
140
10.0
0.0
-10.0
-20.0
-30.0
0.0
-10.0
-20.0
-30.0
-20
0
20
40
60
80
100
120
-40.0
-40 -20
140
0
20
Temperature (°C)
Figure 5.
120
Input bias current vs. temperature
Vcc = 1.8V
Vicm = 0.9V
-40.0
-40
100
Temperature (°C)
Input offset voltage (mV)
Figure 3.
20
Supply current/amplifier vs. supply Figure 6.
voltage
600
550
500
500
40 60
80 100
Temperature (°C)
120 140
Supply current/amplifier vs.
temperature
Supply current (µA)
Supply current (µA)
Vcc = 5V
400
Tamb = 25°C
300
200
400
Vcc = 1.8V
350
300
100
0
0
8/26
Vcc = 3V
450
2
4
Supply voltage (V)
6
8
250
-40
-20
0
20
40
60
80
Temperature (°C)
100
120
140
TS1871-TS1872-TS1874
Figure 7.
Electrical characteristics
Common mode rejection vs.
temperature
115
110
Vcc = 3V
Vicm = 0V
105
100
Vcc = 5V
Vicm = 0V
95
90
85
-40
Figure 9.
-20
0
20
40
60
80
Temperature (°C)
100
120
Vcc = 1.8V
Vicm = 0V
100
90
80
70
60
-40
140
-20
0
20
Supply voltage rejection vs.
temperature
60
80
100
120
140
Figure 10. Supply voltage rejection vs.
temperature
110
Supply voltage rejection (dB)
Vcc = 3V
Vicm = 0V
100
90
80
70
60
-40
-20
0
20
40
60
80
100
120
Vcc = 5V
Vicm = 0V
100
90
80
70
60
-40
140
-20
0
20
Figure 11. Power supply voltage rejection vs.
frequency
60
80
100
120
140
Figure 12. Open loop gain vs. frequency
-20
110
Vcc = 1.8V
Vicm = 0.9V
Vcc = 1.8V
Vicm = 0.7V
Gain = 10
Open loop gain (dB)
-30
40
Temperature (°C)
Temperature (°C)
Supply voltage rejection (dB)
40
Temperature (°C)
110
Supply voltage rejection (dB)
Supply voltage rejection vs.
temperature
110
Vcc = 1.8V
Vicm = 0V
Supply voltage rejection (dB)
Common mode rejection (dB)
120
Figure 8.
-40
-50
-60
100
RL = 2 kOhms
90
RL = 600 Ohms
80
-70
-80
100
1000
10000
Frequency (Hz)
100000
70
-40
-20
0
20
40
60
80
Temperature (°C)
100
120
140
9/26
Electrical characteristics
TS1871-TS1872-TS1874
Figure 13. Open loop gain vs. temperature
Figure 14. Open loop gain vs. temperature
110
110
RL = 2 kOhms
100
90
RL = 600 Ohms
80
70
-40
-20
0
20
40
60
80
100
120
RL = 2 kOhms
Vcc = 5V
Vicm = 2.5V
Open loop gain (dB)
Open loop gain (dB)
Vcc = 3V
Vicm = 1.5V
100
90
80
70
-40
140
RL = 600 ohms
-20
0
20
Temperature (°C)
Figure 15. High level output voltage vs.
temperature
Voltage referenced to Gnd (mV)
Voltage referenced to VCC (mV)
120
140
90
80
Vcc = 3V
70
Vcc = 1.8V
60
50
-20
0
20
40
60
80
100
120
100
90
Vcc = 3V
70
60
Vcc = 1.8V
50
40
-40
140
Vcc = 5V
80
-20
0
20
Temperature (°C)
40
60
80
100
120
140
Temperature (°C)
Figure 17. High level output voltage vs.
temperature
Figure 18. Low level output voltage vs.
temperature
80
80
RL = 2 kohms
Voltage referenced to VCC (mV)
Voltage referenced to VCC (mV)
100
RL = 600 ohms
Vcc = 5V
100
70
Vcc = 5V
60
50
Vcc = 3V
40
Vcc = 1.8V
30
-20
0
20
40
60
Temperature (°C)
10/26
80
110
RL = 600 ohms
20
-40
60
Figure 16. Low level output voltage vs.
temperature
110
40
-40
40
Temperature (°C)
80
100
120
140
RL = 2 kohms
70
Vcc = 5V
60
50
Vcc = 3V
40
Vcc = 1.8V
30
20
-40
-20
0
20
40
60
Temperature (°C)
80
100
120
140
TS1871-TS1872-TS1874
Electrical characteristics
Figure 19. Output current vs. temperature
Figure 20. Output current vs. temperature
100
100
Isink
50
Output current (mA)
Output current (mA)
Isink
Vcc = 1.8V
Vid = 1V
0
Isource
-50
-100
-40
-20
0
20
40
60
80
100
120
50
Vcc = 3V
Vid = 1V
0
Isource
-50
-100
-40
140
-20
0
20
Temperature (°C)
40
60
80
100
120
140
Temperature (°C)
Figure 21. Output current vs. temperature
Figure 22. Output current vs. output voltage
100
100
T = 25 °C
T = -40 °C
Output current (mA)
Output current (mA)
Isink
50
Vcc = 5V
Vid = 1V
0
Isource
-50
50
sink
T = 125 °C
Vcc = 1.8V
Vid = 0.1V
Vicm = 0.9V
0
T = -40 °C
-50 T = 125 °C
T = 25 °C
source
-100
-40
-20
0
20
40
60
80
100
120
-100
0.0
140
0.5
1.0
Temperature (°C)
1.5
2.0
Output voltage (V)
Figure 23. Output current vs. output voltage
Figure 24. Output current vs. output voltage
100
100
T = -40 °C
T = -40 °C
50
sink
Output current (mA)
Output current (mA)
T = 25 °C
T = 125 °C
Vcc = 3V
Vid = 0.1V
Vicm = 1.5V
0
T = 125 °C
-50
T = 25 °C
0.5
1.5
2.0
Output voltage (V)
2.5
3.0
T = 25 °C
T = 125 °C
Vcc = 5V
Vid = 0.1V
Vicm = 2.5V
T = 125 °C
T = 25 °C
T = -40 °C
source
1.0
sink
0
-50
T = -40 °C
-100
0.0
50
3.5
-100
0.0
1.0
source
2.0
3.0
Output voltage (V)
4.0
5.0
11/26
Electrical characteristics
TS1871-TS1872-TS1874
Figure 25. Gain and phase vs. frequency
RL = 10K
CL = 100 pF
Vcc = 1.8V
60
160
60
140
50
120
gain
phase
30
100
RL = 10K
CL = 100 pF
Vcc = 3V
160
140
120
gain
30
100
phase
20
80
20
80
10
60
10
60
0
1E+3
0
1E+3
40
1E+4
1E+5
Frequency (Hz)
1E+6
180
RL = 10K
CL = 100 pF
Vcc = 5V
50
Vcc = 5V
160
140
120
gain
phase
100
20
80
10
60
0
1E+3
1E+5
1.60
1E+6
Vicm = Vcc/2
RL = 10kohms
CL = 100 pF
Vcc = 3V
1.50
Vcc = 1.8V
1.40
1.30
1.20
-40
40
1E+4
1E+6
1.70
Phase (°)
40
30
1E+5
Figure 28. Gain bandwidth product vs.
temperature
Gain-bandwidth product (MHz)
70
60
40
1E+4
Frequency (Hz)
Figure 27. Gain and phase vs. frequency
Gain (dB)
40
180
Phase (°)
40
70
Phase (°)
Gain (dB)
50
180
Gain (dB)
70
Figure 26. Gain and phase vs. frequency
-20
0
20
40
60
80
100
120
140
Temperature (°C)
Frequency (Hz)
Figure 29. Gain bandwidth product vs. supply Figure 30. Slew rate vs. temperature
voltage
0.55
0.50
1.5
Slew rate (V/µs)
Gain bandwidth product (MHz)
2.0
RL = 2 kohms
CL = 220 pF
Vicm = Vcc/2
T = 25°C
1.0
negative slew rate
positive slew rate
0.45
0.40
0.35
0.5
1
12/26
Vcc = 1.8V
gain = +1
Vin = 0.4 to 1.4V
RL = 10kohm
CL = 100 pF
2
3
4
Supply voltage (V)
5
0.30
-40
-20
0
20
40
60
80
Temperature (°C)
100
120
140
TS1871-TS1872-TS1874
Electrical characteristics
Figure 31. Slew rate vs. temperature
0.70
Slew rate (V/µs)
0.60
0.75
positive slew rate
Vcc = 3V
gain = +1
Vin = 1 to 2V
RL = 10kohm
CL = 100 pF
0.70
0.65
Slew rate (V/µs)
0.65
Figure 32. Slew rate vs. temperature
negative slew rate
0.55
0.50
0.45
positive slew rate
negative slew rate
0.60
0.55
0.50
0.45
0.40
0.35
-40
Vcc = 5V
gain = +1
Vin = 2 to 3V
RL = 10kohms
CL = 100 pF
0.40
-20
0
20
40
60
80
100
120
0.35
-40
140
-20
0
20
Temperature (°C)
Figure 33. Phase margin vs. load capacitor
80
100
120
140
80
Vcc = 1.8V
gain = 40dB
RL = 1Kohm
50
75
40
Phase margin (°)
Phase margin (°)
60
Figure 34. Phase margin vs. output current
60
30
20
10
70
Vcc = 1.8V
RL = 1 kOhm
CL = 220 pF
65
60
55
50
0
45
-10
10
100
40
-10
1000
Figure 35. Gain margin vs. output current
0
5
10
Figure 36. Equivalent input noise vs.
frequency
35
Equivalent input noise (nV/sqrt(Hz))
0
-5
Vcc = 1.8V
RL = 1 kOhm
CL = 220 pF
-10
-15
-20
-25
-10
-5
DC output current (mA)
Load capacitor (pF)
GainmMargin (dB)
40
Temperature (°C)
-5
0
5
DC output current (mA)
10
30
25
20
15
10
5
1E+1
Vcc = 1.8V
gain = 100
Rs = 100 ohms
1E+2
1E+3
1E+4
1E+5
Frequency (Hz)
13/26
Electrical characteristics
TS1871-TS1872-TS1874
Figure 37. Distortion vs. output voltage
Figure 38. Distortion vs. output voltage
100.000
10.000
Distortion (%)
Distortion (%)
10.000
100.000
RL= 1Kohms
Gain = -1
F = 1000 Hz
Vcc = 1.8V
1.000
0.100
0.010
0.001
0.00
RL= 1Kohms
Gain = -1
F = 1000 Hz
Vcc = 3V
1.000
0.100
0.010
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.001
0.00
0080
0.20
Output voltage (VRMS)
Figure 39. Distortion vs. output voltage
Distortion (%)
Distortion (%)
10.000
0.100
0.010
0.50
1.00
1.50
1.000
0.100
0.001
0.00
2.00
0.20
0.60
0.80
1.00
1.20
Figure 42. Distortion vs. output voltage
100.000
RL= 1500 ohms
Gain = -1
F = 1000 Hz
Vcc = 2.7V
10.000
Distortion (%)
Distortion (%)
0.40
Output voltage (VRMS)
100.000
1.000
0.100
RL= 4700 ohms
Gain = -1
F = 1000 Hz
Vcc = 2.7V
1.000
0.100
0.010
0.010
0.20
0.40
0.60
0.80
Output voltage (VRMS)
14/26
1.20
0.010
Figure 41. Distortion vs. output voltage
0.001
0.00
1.00
RL= 150 ohms
Gain = -1
F = 1000 Hz
Vcc = 2.7V
Output voltage (VRMS)
10.000
0.80
100.000
RL= 1Kohms
Gain = -1
F = 1000 Hz
Vcc = 5V
1.000
0.001
0.00
0.60
Figure 40. Distortion vs. output voltage
100.000
10.000
0.40
Output voltage (VRMS)
1.00
1.20
0.001
0.00
0.20
0.,40
0.60
0.80
Output voltage (VRMS)
1.00
1.20
TS1871-TS1872-TS1874
Electrical characteristics
Figure 43. Distortion vs. frequency
Distortion (%)
0.012
0.015
Vcc = 1.8V
Vout = 1Vpp
RL = 1Kohms
gain = -1
0.013
Distortion (%)
0.014
Figure 44. Distortion vs. frequency
0.010
0.008
0.006
Vcc = 3V
Vout = 1Vpp
RL = 1Kohms
gain = -1
0.010
0.007
0.005
0.003
0,004.
1E+1
1E+2
1E+3
1E+4
0.000
1E+1
1E+5
1E+2
Frequency (Hz)
Figure 45. Distortion vs. frequency
1E+5
0.150
Vcc = 1.8V
Vout = 1Vpp
RL = 32 ohms
gain = -1
0.125
0.100
Distortion (%)
Distortion (%)
1E+4
Figure 46. Distortion vs. frequency
0.150
0.125
1E+3
Frequency (Hz)
0.075
0.050
0.025
Vcc = 3V
Vout = 1Vpp
RL = 32 ohms
gain = -1
0.100
0.075
0.050
0.025
0.000
1E+1
1E+2
1E+3
1E+4
0.000
1E+1
1E+5
Frequency (Hz)
1E+2
1E+3
1E+4
1E+5
Frequency (Hz)
Figure 47. Output power vs. supply voltage
60
RL = 32 ohms
10% distortion
Output power (mW)
50
1% distortion
40
30
0.1% distortion
20
10
0
1
2
3
4
5
6
Supply voltage (V)
15/26
Package information
3
TS1871-TS1872-TS1874
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK® packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
3.1
SOT23-5 package information
Figure 48. SOT23-5 package mechanical drawing
Table 6.
SOT23-5 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Max.
Min.
Typ.
Max.
A
0.90
1.45
35.4
57.1
A1
0.00
0.15
0.00
5.9
A2
0.90
1.30
35.4
51.2
b
0.35
0.50
13.7
19.7
C
0.09
0.20
3.5
7.8
D
2.80
3.00
110.2
118.1
E
2.60
3.00
102.3
118.1
E1
1.50
1.75
59.0
68.8
e
0.95
37.4
e1
1.9
74.8
L
16/26
Typ.
Mils
0.35
0.55
13.7
21.6
TS1871-TS1872-TS1874
3.2
Package information
DIP8 package information
Figure 49. DIP8 package mechanical drawing
Table 7.
DIP8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
5.33
Max.
0.210
A1
0.38
0.015
A2
2.92
3.30
4.95
0.115
0.130
0.195
b
0.36
0.46
0.56
0.014
0.018
0.022
b2
1.14
1.52
1.78
0.045
0.060
0.070
c
0.20
0.25
0.36
0.008
0.010
0.014
D
9.02
9.27
10.16
0.355
0.365
0.400
E
7.62
7.87
8.26
0.300
0.310
0.325
E1
6.10
6.35
7.11
0.240
0.250
0.280
e
2.54
0.100
eA
7.62
0.300
eB
L
10.92
2.92
3.30
3.81
0.430
0.115
0.130
0.150
17/26
Package information
3.3
TS1871-TS1872-TS1874
SO-8 package information
Figure 50. SO-8 package mechanical drawing
Table 8.
SO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.75
0.25
Max.
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
H
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
1°
8°
1°
8°
ccc
18/26
Inches
0.10
0.004
TS1871-TS1872-TS1874
3.4
Package information
TSSOP8 package information
Figure 51. TSSOP8 package mechanical drawing
Table 9.
TSSOP8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.2
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
1.00
0.65
k
0°
L
0.45
0.60
0.006
0.039
0.041
0.0256
8°
0°
0.75
0.018
8°
0.024
L1
1
0.039
aaa
0.1
0.004
0.030
19/26
Package information
3.5
TS1871-TS1872-TS1874
MiniSO-8 package
Figure 52. MiniSO-8 package mechanical drawing
Table 10.
MiniSO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.1
A1
0
A2
0.75
b
Max.
0.043
0.15
0
0.95
0.030
0.22
0.40
0.009
0.016
c
0.08
0.23
0.003
0.009
D
2.80
3.00
3.20
0.11
0.118
0.126
E
4.65
4.90
5.15
0.183
0.193
0.203
E1
2.80
3.00
3.10
0.11
0.118
0.122
e
L
0.85
0.65
0.40
0.60
0.006
0.033
0.80
0.016
0.024
0.95
0.037
L2
0.25
0.010
ccc
0°
0.037
0.026
L1
k
20/26
Inches
8°
0.10
0°
0.031
8°
0.004
TS1871-TS1872-TS1874
3.6
Package information
DIP14 package information
Figure 53. DIP14 package mechanical drawing
Table 11.
DIP14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
a1
0.51
B
1.39
Typ.
Inches
Max.
Min.
Typ.
Max.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
1.27
0.130
2.54
0.050
0.100
21/26
Package information
3.7
TS1871-TS1872-TS1874
SO-14 package information
Figure 54. SO-14 package mechanical drawing
Table 12.
SO-14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
a1
Inches
Max.
Typ.
1.75
0.1
0.2
a2
Max.
0.068
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
8.55
8.75
0.336
0.344
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
22/26
Min.
0.68
0.026
8° (max.)
TS1871-TS1872-TS1874
3.8
Package information
TSSOP14 package information
Figure 55. TSSOP14 package mechanical drawing
A
A2
A1
K
e
b
L
c
E
D
E1
PIN 1 IDENTIFICATION
1
Table 13.
TSSOP14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.2
A1
0.05
A2
0.8
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
e
1
0.65 BSC
K
0°
L1
0.45
0.60
0.0256 BSC
8°
0°
0.75
0.018
8°
0.024
0.030
23/26
Ordering information
TS1871-TS1872-TS1874
4
Ordering information
Table 14.
Order codes
Order code
Temperature
range
TS1871ID/IDT
TS1871IAID/AIDT
TS1871IYD/IYDT(1)
TS1871IAIYD/AIYDT(1)
Package
Packing
Marking
Tube or
tape & reel
1871I
SO-8
SO-8
(Automotive grade)
Tube or
tape & reel
SOT23-5L
Tape & reel
K182
SOT23-5L
(Automotive grade)
Tape & reel
TS1872IN
TS1872AIN
DIP8
Tube
TS1872ID/IDT
TS1872AID/AIDT
SO-8
K183
1872IN
1872AIN
TS1872IYD/IYDT(1)
TS1872AIYD/AIYDT(1)
Tube or
tape & reel
SO-8
(Automotive grade)
Tube or
tape & reel
TSSOP8
Tape & reel
1872Y
1872AY
1872Y
TS1872IST
TS1872AIST
MiniSO-8
Tape & reel
TS1874IN
TS1874AIN
DIP14
TS1874ID/IDT
TS1874AID/AIDT
SO-14
TS1874IYPT(1)
TS1874AIYPT(1)
1872AI
1872A
Tape & reel
TS1874IPT
TS1874AIPT
1872I
1872I
-40°C to +125°C
TSSOP8
(Automotive grade)
TS1874IYD/IYDT(1)
TS1874AIYD/AIYDT(1)
1871AY
K172
TS1871IYLT(1)
TS1871AIYLT(1)
TS1872IYPT(1)
TS1872AIYPT(1)
1871Y
K171
TS1871ILT
TS1871AILT
TS1872IPT
TS1872AIPT
1871AI
872AY
K171
K172
Tube
1874IN
Tube
1874AIN
Tube or
tape & reel
1874I
SO-14
(Automotive grade)
Tube or
tape & reel
TSSOP14
Tape & reel
1874AI
TS1874Y
TS1874AY
1874I
1874AI
TSSOP14
(Automotive grade)
TS1874Y
Tape & reel
TS1874AY
1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 & Q 002 or equivalent are on-going.
24/26
TS1871-TS1872-TS1874
5
Revision history
Revision history
Table 15.
Document revision history
Date
Revision
Changes
1-Apr-2002
1
First release.
2-Jan-2005
2
Modifications on AMR Table 1 on page 3 (explanation of Vid and
Vi limits).
21-May-2007
3
Added limits over temperature range in Table 3 on page 5,
Table 4 on page 6, Table 5 on page 7.
Added SVR in Table 5 (SVR parameter removed from Table 3
and Table 4).
Added equivalent input voltage noise in Table 3, Table 4, and
Table 5.
Added Rthjc values in Table 1.
Added automotive grade part numbers to order codes table.
Moved order codes table to Section 4 on page 24.
Updated format of package information.
17-Jan-2008
4
Updated footnote for automotive grade order codes in Table 14.
25/26
TS1871-TS1872-TS1874
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
26/26