ETC AT17LV040A

Features
• EE Programmable 65,536 x 1-, 131,072 x 1-, 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1-,
•
•
•
•
•
•
•
•
•
•
•
2,097,152 x 1-, and 4,194,304 x 1-bit Serial Memories Designed to Store Configuration
Programs for Altera FLEX® and APEX FPGAs (Device Selection Guide Included)
Available as a 3.3V (-10%) to 5.0V (+10%) Version
In-System Programmable (ISP) via 2-wire Bus
Simple Interface to SRAM FPGAs
Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera FLEX ®, APEX™
Devices, Lucent ORCA® FPGAs, Xilinx XC3000™, XC4000™, XC5200™, Spartan®, Virtex®
FPGAs, Motorola MPA1000 FPGAs
Cascadable Read-back to Support Additional Configurations or Higher-density Arrays
Very Low-power CMOS EEPROM Process
Programmable Reset Polarity
Available 8-lead PDIP, 20-lead PLCC, 32-lead TQFP and 44-lead PLCC Packages (Pin
Compatible Across Product Family)
Emulation of Atmel’s AT24CXXX Serial EEPROMs
Low-power Standby Mode
High-reliability
– Endurance: 100,000 Write Cycles
– Data Retention: 90 Years for Industrial Parts (at 85°C) and 190 Years for
Commercial Parts (at 70°C)
Description
The AT17A series FPGA configuration EEPROMs (Configurators) provide an easy-touse, cost-effective configuration memory for Field Programmable Gate Arrays. The
AT17A series device is packaged in the 8-lead PDIP(1), 20-lead PLCC, 32-lead TQFP
and 44-lead PLCC, see Table 1. The AT17A series configurator uses a simple serialaccess procedure to configure one or more FPGA devices. The user can select the
polarity of the reset function by programming four EEPROM bytes. These devices also
support a write-protection mechanism within its programming mode.
Note:
1. The 8-lead LAP and SOIC packages for the AT17LV65A/128A/256A do not have an
A label. However, the 8-lead packages are pin compatible with the 8-lead package
of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040 datasheet
available on the Atmel web site for more information.
The AT17A series configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable.
Table 1. AT17A Series Packages
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A
AT17LV010A
AT17LV002A
AT17LV040A
8-lead
PDIP
Yes
Yes
Yes
–
–
20-lead
PLCC
Yes
Yes
Yes
Yes
–
32-lead
TQFP
–
–
Yes
Yes
–
44-lead
PLCC
–
–
–
–
Yes
Package
FPGA
Configuration
EEPROM
Memory
AT17LV65A
AT17LV128A
AT17LV256A
AT17LV512A
AT17LV010A
AT17LV002A
AT17LV040A
3.3V to 5V
System Support
Rev. 2322B–CNFG–05/02
1
Pin Configuration
8-lead PDIP
DATA
DCLK
(1)
(WP )RESET/OE
nCS
1
2
3
4
VCC
SER_EN
(A2) nCASC
GND
8
7
6
5
18
17
16
15
14
9
10
11
12
13
4
5
6
7
8
SER_EN
NC
NC
NC (READY(2))
NC
nCS
GND
NC
(A2) nCASC
NC
DCLK
WP1(2)
NC
(WP(1)) NC
RESET/OE
3
2
1
20
19
NC
DATA
NC
VCC
NC
20-lead PLCC
32
31
30
29
28
27
26
25
NC
DATA
NC
NC
NC
VCC
NC
NC
32-lead TQFP
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
NC
SER_EN
NC
NC
READY
NC
NC
NC
NC
nCS
NC
GND
NC
NC
(A2) nCASC
NC
9
10
11
12
13
14
15
16
NC
DCLK
NC
(3)
(WP1 ) NC
NC
NC
RESET/OE
NC
Notes:
2
1. This pin is only available on AT17LV65A/128A/256A devices.
2. This pin is only available on AT17LV512A/010A/002A devices.
3. This pin is only available on AT17LV010A/002A devices.
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
39
38
37
36
35
34
33
32
31
30
29
18
19
20
21
22
23
24
25
26
27
28
7
8
9
10
11
12
13
14
15
16
17
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
READY
NC
RESET/OE
NC
nCS
NC
NC
GND
NC
NC
nCASC/A2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
6
5
4
3
2
1
44
43
42
41
40
NC
DCLK
NC
NC
DATA
NC
VCC
NC
NC
SER_EN
NC
44-lead PLCC
3
2322B–CNFG–05/02
Block Diagram
SER_EN
WP1(2)
OSCILLATOR
CONTROLL
(3)
OSCILLATOR
POWER ON
RESET
(2)
DCLK READY
Notes:
4
RESET/OE
(1)
(WP )
nCS
nCASC
1. This pin is only available on AT17LV65A/128A/256A devices.
2. This pin is only available on AT17LV512A/010A/002A/040A devices.
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
Device Description
The control signals for the configuration EEPROM (nCS, RESET/OE and DCLK) interface directly with the FPGA device control signals. All FPGA devices can control the
entire configuration process and retrieve data from the configuration EEPROM without
requiring an external controller.
The configuration EEPROM’s RESET/OE and nCS pins control the tri-state buffer on
the DATA output pin and enable the address counter and the oscillator. When
RESET/OE is driven Low, the configuration EEPROM resets its address counter and tristates its DATA pin. The nCS pin also controls the output of the AT17A series configurator. If nCS is held High after the RESET/OE pulse, the counter is disabled and the DATA
output pin is tri-stated. When nCS is driven subsequently Low, the counter and the
DATA output pin are enabled. When RESET/OE is driven Low again, the address
counter is reset and the DATA output pin is tri-stated, regardless of the state of the nCS.
When the configurator has driven out all of its data and nCASC is driven Low, the device
tri-states the DATA pin to avoid contention with other configurators. Upon power-up, the
address counter is automatically reset.
This is the default setting for the device. Since almost all FPGAs use RESET Low and
OE High, this document will describe RESET/OE.
5
2322B–CNFG–05/02
Pin Description
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
AT17LV040A
Name
I/O
20
PLCC
8
PDIP
20
PLCC
32
TQFP
20
PLCC
32
TQFP
44
PLCC
DATA
I/O
2
1
2
31
2
31
2
DCLK
I
4
2
4
2
4
2
5
WP1
I
–
–
5
4
5
4
–
RESET/OE
I
8
7
8
7
19
8
3
–
–
–
–
–
WP
I
nCS
I
GND
9
4
9
10
9
10
21
10
5
10
12
10
12
24
12
6
12
15
12
15
25
nCASC
O
A2
I
READY
O
–
–
15
20
15
20
29
SER_EN
I
18
7
18
23
18
23
41
20
8
20
27
20
27
44
V CC
DATA
Three-state DATA output for configuration. Open-collector bi-directional pin for
programming.
DCLK
Clock output or clock input. Rising edges on DCLK increment the internal address
counter and present the next bit of data to the DATA pin. The counter is incremented
only if the RESET/OE input is held High, the nCS input is held Low, and all configuration
data has not been transferred to the target device (otherwise, as the master device, the
DCLK pin drives Low).
WP1
WRITE PROTECT (1). This pin is used to protect portions of memory during programming, and it is disabled by default due to internal pull-down resistor. This input pin is not
used during FPGA loading operations. This pin is only available on
AT17LV512A/010A/002A devices.
RESET/OE
Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low
logic level resets the address counter. A High logic level (with nCS Low) enables DATA
and permits the address counter to count. In the mode, if this pin is Low (reset), the
internal oscillator becomes inactive and DCLK drives Low. The logic polarity of this input
is programmable and must be programmed active High (RESET active Low) by the user
during programming for Altera applications.
WP
Write protect (WP) input (when nCS is Low) during programming only (SER_EN Low).
When WP is Low, the entire memory can be written. When WP is enabled (High), the
lowest block of th e memory cann ot be written . This p in is o nly ava ila ble o n
AT17LV65A/128A/256A devices.
6
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
nCS
Chip Select input (active Low). A Low input (with OE High) allows DCLK to increment
the address counter and enables DATA to drive out. If the AT17A series is reset with
nCS Low, the device initializes as the first (and master) device in a daisy-chain. If the
AT17A series is reset with nCS High, the device initializes as a subsequent AT17A
series device in the chain.
GND
Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended.
nCASC
Cascade Select Output (active Low). This output goes Low when the address counter
has reached its maximum value. In a daisy-chain of AT17A series devices, the nCASC
pin of one device is usually connected to the nCS input pin of the next device in the
chain, which permits DCLK from the master configurator to clock data from a subsequent AT17A series device in the chain.
A2
Device selection input, A2. This is used to enable (or select) the device during programming (i.e., when SER_EN is Low). A2 has an internal pull-down resistor.
READY
Open collector reset state indicator. Driven Low during power-on reset cycle, released
when power-up is complete. (recommended 4.7 kΩ pull-up on this pin if used).
SER_EN
Serial enable must be held High during FPGA loading operations. Bringing SER_EN
Low enables the 2-wire Serial Programming Mode. For non-ISP applications, SER_EN
should be tied to VCC.
VCC
+3.3V (-10%) to 5.0V (+10%) power supply pin. AT17LV(A) devices with date codes of
0902 and later are tested to an extended voltage range. These parts can now be used in
both 3.3V (-10%) to 5.0V (+10%) applications and replace the AT17C(A) 5V-only
devices.
7
2322B–CNFG–05/02
FPGA Master Serial
Mode Summary
The I/O and logic functions of any SRAM-based FPGA are established by a configuration program. The program is loaded either automatically upon power-up, or on
command, depending on the state of the FPGA mode pins. In Master mode, the FPGA
automatically loads the configuration program from an external memory. The AT17A
Serial Configuration EEPROM has been designed for compatibility with the Master
Serial mode.
This document discusses the Altera FLEX FPGA device interfaces
Control of
Configuration
Cascading Serial
Configuration
EEPROMs
Most connections between the FPGA device and the AT17A Serial EEPROM are simple
and self-explanatory.
•
The DATA output of the AT17A series configurator drives DIN of the FPGA devices.
•
The master FPGA DCLK output or external clock source drives the DCLK input of
the AT17A series configurator.
•
The nCASC output of any AT17A series configurator drives the nCS input of the next
configurator in a cascaded chain of EEPROMs.
•
SER_EN must be connected to VCC (except during ISP).
For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration memories, cascaded configurators provide additional memory.
After the last bit from the first configurator is read, the next clock signal to the configurator asserts its nCASC output low and disables its DATA line driver. The second
configurator recognizes the low level on its nCS input and enables its DATA output.
After configuration is complete, the address counters of all cascaded configurators are
reset if the RESET/OE on each configurator is driven to a Low level.
If the address counters are not to be reset upon completion, then the RESET/OE input
can be tied to a High level.
AT17A Series Reset
Polarity
The AT17A series configurator allows the user to program the polarity of the RESET/OE
pin as either RESET/OE or RESET/OE. This feature is supported by industry-standard
programmer algorithms.
Programming Mode
The programming mode is entered by bringing SER_EN Low. In this mode the chip can
be programmed by the 2-wire serial bus. The programming is done at VCC supply only.
Programming super voltages are generated inside the chip.
Standby Mode
The AT17LV65A/128A/256A enters a low-power standby mode whenever nCS is
asserted High. In this mode, the configurator consumes less than 50 µA of current
at 3.3V (100 µA for the AT17LV512A/010A/002A/040A). The output remains in a highimpedance state regardless of the state of the RESET/OE input.
8
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
Absolute Maximum Ratings*
*NOTICE:
Operating Temperature.................................. -55°C to +125 °C
Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended
periods of time may affect device reliability.
Storage Temperature ..................................... -65 °C to +150°C
Voltage on Any Pin
with Respect to Ground ..............................-0.1V to VCC +0.5V
Supply Voltage (VCC ) .........................................-0.5V to +7.0V
Maximum Soldering Temp. (10 sec. @ 1/16 in.)............. 260°C
ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V
Operating Conditions
AT17LV65A/
AT17LV128A/
AT17LV256A/
AT17LV512A/
AT17LV010A
Symbol
VCC
Description
AT17LV002A/
AT17LV040A
Min
Max
Min
Max
Units
Commercial
Supply voltage relative to GND
-0°C to +70°C
3.0
5.5
3.15
5.5
V
Industrial
Supply voltage relative to GND
-40°C to +85°C
3.0
5.5
3.15
5.5
V
Military
Supply voltage relative to GND
-55°C to +125°C
3.0
5.5
3.15
5.5
V
DC Characteristics
AT17LV65A/
AT17LV128A/
AT17LV256A
Symbol
Description
VIH
AT17LV512A/
AT17LV010A
AT17LV002A/
AT17LV040A
Min
Max
Min
Max
Min
Max
Units
High-level Input Voltage
2.0
VCC
2.0
VCC
2.0
VCC
V
VIL
Low-level Input Voltage
0
0.8
0
0.8
0
0.8
V
VOH
High-level Output Voltage (IOH = -2.5 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
VOH
High-level Output Voltage (IOH = -2 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
VOH
High-level Output Voltage (IOH = -2 mA)
VOL
Low-level Output Voltage (IOL = +2.5 mA)
ICCA
Supply Current, Active Mode
IL
Input or Output Leakage Current (V IN = VCC or GND)
ICCS
Supply Current, Standby Mode
2.4
2.4
2.4
V
Commercial
0.4
2.4
0.4
2.4
0.4
2.4
V
V
Industrial
0.4
2.4
0.4
2.4
0.4
2.4
V
V
Military
-10
0.4
0.4
0.4
V
5
5
5
mA
10
µA
10
-10
10
-10
Commercial
50
100
100
µA
Industrial/
Military
100
100
100
µA
9
2322B–CNFG–05/02
AC Characteristics
nCS
TSCE
TSCE
THCE
RESET/OE
TLC
THOE
THC
DCLK
TOE
TCAC
TOH
TDF
TCE
DATA
TOH
AC Characteristics when Cascading
RESET/OE
nCS
DCLK
TCDF
DATA
LAST BIT
TOCK
FIRST BIT
TOCE
TOOE
nCASL
TOCE
10
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
AC Characteristics
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
AT17LV040A
Min
Min
Min
Min
Symbol
Description
Max
Max
Max
Max
Units
TOE(2)
RESET/OE to Data Delay
TCE(2)
nCS to Data Delay
TCAC(2)
DCLK to Data Delay
Data Hold from nCS,
OE, or DCLK
Commercial
0
0
0
0
ns
TOH
Military(1)
0
0
0
0
ns
TDF(3)
nCS or OE to Data
Float Delay
Commercial
55
50
50
50
ns
Military(1)
55
50
50
50
ns
TLC
DCLK Low Time
THC
DCLK High Time
TSCE
Commercial
50
50
50
50
ns
Military(1)
55
55
55
55
ns
Commercial
60
55
55
55
ns
Military(1)
60
60
60
60
ns
Commercial
75
60
60
60
ns
Military(1)
80
65
65
65
ns
Commercial
25
20
20
20
ns
Military(1)
25
20
20
20
ns
Commercial
25
20
20
20
ns
Military(1)
25
20
20
20
ns
nCS Setup Time to DCLK
(to guarantee proper counting)
Commercial
35
20
20
20
ns
Military(1)
50
25
25
25
ns
nCS Hold Time from DCLK
(to guarantee proper counting)
Commercial
0
0
0
0
ns
THCE
Military(1)
0
0
0
0
ns
OE Low Time
(guarantees counter is reset)
Commercial
25
20
20
20
ns
THOE
Military(1)
25
20
20
20
ns
Maximum Input
Clock Frequency
Commercial
10
15
15
15
MHz
FMAX
Military(1)
10
10
10
10
MHz
TLC
DCLK Low Time Master Mode
THC
VRDY
Notes:
Commercial
30
300
30
300
ns
Military(1)
30
300
30
300
ns
DCLK High Time
Master Mode
Commercial
30
300
30
300
ns
Military(1)
30
300
30
300
ns
Ready Pin Open
Collector Voltage
Commercial
1.2
2.4
1.2
2.4
V
Military(1)
1.2
2.4
1.2
2.4
V
1. Preliminary specifications for military operating range only.
2. AC test lead = 50 pF.
3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
11
2322B–CNFG–05/02
AC Characteristics when Cascading
Symbol
Description
TCDF(3)
DCLK to Data Float Delay
TOCK(2)
DCLK to nCASC Delay
TOCE
(2)
nCS to nCASC Delay
TOOE(2)
RESET/OE to
nCASC Delay
FMAX
Maximum Input
Clock Frequency
Notes:
12
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
AT17LV040A
Min
Min
Min
Min
Max
Max
Max
Max
Units
Commercial
60
50
50
50
ns
Industrial/
Military(1)
60
50
50
50
ns
Commercial
55
50
50
50
ns
Industrial/
Military(1)
60
55
55
55
ns
Commercial
55
35
35
35
ns
Industrial/
Military(1)
60
40
40
40
ns
Commercial
40
35
35
35
ns
Industrial/
Military(1)
45
35
35
35
ns
Commercial
8
12.5
12
12
ns
Industrial/
Military(1)
8
10
10
10
ns
1. Preliminary specifications for military operating range only.
2. AC test lead = 50 pF.
3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
Thermal Resistance Coefficients(1)
AT17LV65A/
AT17LV128A/
AT17LV256A
Package Type
8P3
20J
Plastic Dual Inline Package (PDIP)
Plastic Leaded Chip Carrier
(PLCC)
32A
Thin Plastic Quad Flat Package
(TQFP)
44J
Plastic Leaded Chip Carrier
(PLCC)
Notes:
θJC [°C/W]
θJA [°C/W]
θJA [°C/W]
(2)
AT17LV002A
AT17LV040A
37
(2)
θJC [°C/W]
AT17LV512A/
AT17LV010A
107
35
35
35
90
90
90
–
–
15
15
–
–
50
50
θJC [°C/W]
θJA [°C/W](2)
θJC [°C/W]
θJA [°C/W]
(2)
1. For more information refer to the “Thermal Characteristics of Atmel’s Packages”, available on the Atmel web site, at
http://www.atmel.com/atmel/acrobat/doc0636.pdf.
2. Airflow = 0 ft/min.
13
2322B–CNFG–05/02
Figure 1. Ordering Code(1)
AT17LV65A-10PC
Note:
Voltage
Size (Bits)
Special Pinouts
Package
Temperature
3.3V Nominal to
65
= 65K
A
= Altera
P
= 8P3
C = Commercial
5V Nominal
128
= 128K
Blank = Xilinx/Atmel/
Other
J
= 20J
I = Industrial
256
= 256K
A
= 32A
512
= 512K
J
= 44J
010
= 1M
002
= 2M
040
= 4M
1. The 8-lead LAP and SOIC packages for the AT17LV65A/128A/256A do not have an A label. However, the 8-lead packages
are pin compatible with the 8-lead package of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040
datasheet available on the Atmel web site for more information.
Package Type
14
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
20J
20-lead, Plastic J-leaded Chip Carrier (PLCC)
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package Carrier (TQFP)
44J
44-lead, Plastic J-leaded Chip Carrier (PLCC)
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
Ordering Information(1)
Memory Size
(2)
64-Kbit
128-Kbit
256-Kbit(3)
512-Kbit(4)
1-Mbit(5)
2-Mbit(6)
4-Mbit(7)
Notes:
Ordering Code
Package
Operation Range
AT17LV65A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV65A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV128A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV128A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV256A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV256A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV512A-10PC
AT17LV512A-10JC
8P3
20J
Commercial
(0°C to 70°C)
AT17LV512A-10PI
AT17LV512A-10JI
8P3
20J
Industrial
(-40°C to 85°C)
AT17LV010A-10PC
AT17LV010A-10JC
AT17LV010A-10QC
8P3
20J
32A
Commercial
(0°C to 70°C)
AT17LV010A-10PI
AT17LV010A-10JI
AT17LV010A-10QI
8P3
20J
32A
Industrial
(-40°C to 85°C)
AT17LV002A-10JC
AT17LV002A-10QC
20J
32A
Commercial
(0°C to 70°C)
AT17LV002A-10JI
AT17LV002A-10QI
20J
32A
Industrial
(-40°C to 85°C)
AT17LV040A-10PGC
44J
Commercial
(0°C to 70°C)
AT17LV040A-10PGI
44J
Industrial
(-40°C to 85°C)
1. Currently, there are two types of low-density configurators. The new version will be identified by a “B” after the datacode. The
“B” version is fully backward-compatible with the original devices so existing customers will not be affected. The new parts
no longer require a MUX for ISP. See programming specification for more details.
2. Use 64-Kbit density parts to replace Altera EPC1064.
3. Use 256-Kbit density parts to replace Altera EPC1213.
4. Use 512-Kbit density parts to replace Altera EPC1441.
5. Use 1-Mbit density parts to replace Altera EPC1
6. Use 2-Mbit density parts to replace Altera EPC2. Atmel AT17LV002A devices do not support JTAG programming; Atmel
AT17LV002A devices use a 2-wire serial interface for in-system programming.
7. Use 4-Mbit density parts to replace Altera EPC4. Atmel AT17LV040A devices do not support JTAG programming; Atmel
AT17LV040A devices use a 2-wire serial interface for in-system programming.
15
2322B–CNFG–05/02
Packaging Information
8P3 – PDIP
E
1
E1
N
Top View
c
eA
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
D
e
D1
A2 A
MIN
NOM
A2
0.115
0.130
0.195
b
0.014
0.018
0.022
5
b2
0.045
0.060
0.070
6
b3
0.030
0.039
0.045
6
c
0.008
0.010
0.014
D
0.355
0.365
0.400
D1
0.005
E
0.300
0.310
0.325
4
E1
0.240
0.250
0.280
3
SYMBOL
A
b2
b3
b
4 PLCS
Side View
L
Notes:
NOTE
0.210
0.100 BSC
eA
0.300 BSC
0.115
2
3
3
e
L
MAX
0.130
4
0.150
2
1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
01/09/02
R
16
2325 Orchard Parkway
San Jose, CA 95131
TITLE
8P3, 8-lead, 0.300" Wide Body, Plastic Dual
In-line Package (PDIP)
DRAWING NO.
REV.
8P3
B
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
20J – PLCC
PIN NO. 1
1.14(0.045) X 45˚
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
e
E1
E
D2/E2
B1
B
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AA.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
9.779
–
10.033
D1
8.890
–
9.042
E
9.779
–
10.033
E1
8.890
–
9.042
D2/E2
7.366
–
8.382
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
20J
B
17
2322B–CNFG–05/02
32A – TQFP
PIN 1
B
PIN 1 IDENTIFIER
E1
e
E
D1
D
C
0˚~7˚
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ABA.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
8.75
9.00
9.25
D1
6.90
7.00
7.10
E
8.75
9.00
9.25
E1
6.90
7.00
7.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
10/5/2001
R
18
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO.
REV.
32A
B
AT17LV65A/128A/256A/512A/002A/040A
2322B–CNFG–05/02
AT17LV65A/128A/256A/512A/002A/040A
44J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
E1
D2/E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AC.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
17.399
–
17.653
D1
16.510
–
16.662
E
17.399
–
17.653
E1
16.510
–
16.662
D2/E2
14.986
–
16.002
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
44J
B
19
2322B–CNFG–05/02
Atmel Headquarters
Atmel Operations
Corporate Headquarters
Memory
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 487-2600
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
TEL (41) 26-426-5555
FAX (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
TEL (49) 71-31-67-0
FAX (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
TEL (33) 2-40-18-18-18
FAX (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
FAX 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
TEL (33) 4-76-58-30-00
FAX (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
TEL (33) 4-42-53-60-00
FAX (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
FAX 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
TEL (44) 1355-803-000
FAX (44) 1355-242-743
Atmel Programmable SLI Hotline
e-mail
(408) 436-4119
[email protected]
Atmel Programmable SLI e-mail
Web Site
[email protected]
http://www.atmel.com
FAQ
Available on web site
© Atmel Corporation 2002.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty
which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors
which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does
not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted
by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical
components in life support devices or systems.
Atmel® is the registered trademark of Atmel.
FLEX™ is the trademark of Altera Corporation; ORCA ™ is the trademark of Lucent Technologies, Inc.;
SPARTAN ® and Virtex® are the registered trademarks of Xilinx, Inc.; XC3000™, XC4000 ™ and XC5200 ™ are
the trademarks of Xilinx, Inc.; APEX ™ is the trademark of MIPS Technologies; Other terms and product names
may be the trademarks of others.
Printed on recycled paper.
2322B–CNFG–05/02
xM