ETC HD404639RSERIES

HD404639R Series
4-Bit Single-Chip Microcomputer
Rev. 6.0
Sept. 1998
Description
The HD404639R Series is a member of the HMCS400-series microcomputers designed to increase
program productivity with large-capacity memory. The HD404639R Series, completely compatible with
the HD404639 Series, reduces current dissipation in half and includes a high-speed version. Each
microcomputer has a high-precision dual-tone multi frequency (DTMF) generator, four timers, two serial
interfaces, voltage comparator, input capture circuit, 32-kHz oscillator for clock, and four low-power
dissipation modes.
The HD404639R Series includes 5 chips: the HD404638R and HD40A4638R with 8-kword ROM; the
HD404639R and HD40A4639R with 16-kword ROM; the HD407A4639R with 16-kword PROM.
HD40A4638R, HD40A4639R, HD407A4639R are high-speed versions (minimum instruction cycle time:
0.5 µs).
The HD407A4639R is a PROM version ZTAT microcomputer. A program can be written to the PROM
by a PROM writer, which can dramatically shorten system development periods and smooth the process
from debugging to mass production. (The ZTAT version is 27256-compatible.)
ZTAT TM : Zero Turn Around Time. ZTAT is a trademark of Hitachi Ltd.
Features
• 8,192-word × 10-bit ROM (HD404638R, HD40A4638R)
• 16,384-word × 10-bit ROM (HD404639R, HD40A4639R, HD407A4639R)
• 1,152-digit × 4-bit RAM
• 61 I/O pins and 7 dedicated input pins
 12 high-current output pins: Eight 15-mA sinks (a maximum of 7 pins can be used at the same time)
and four 10-mA sources
• Four timer/counters
• Eight-bit input capture circuit
• Three timer outputs (including two PWM outputs)
• Two event counter inputs (including one double-edge function)
• Two clock-synchronous 8-bit serial interfaces
HD404639R Series
• Comparator (4 channels)
• On-chip DTMF generator: fOSC = 400 kHz, 800 kHz, 2 MHz, 3.58 MHz, 4 MHz, 7.16 MHz, or 8 MHz
(7.16 MHz and 8 MHz are only available for HD40A4638R, HD40A4639R and HD407A4639R)
• Built-in oscillators
 Main clock: Ceramic oscillator or crystal (an external clock is also possible)
 Subclock: 32.768-kHz crystal
• Eleven interrupt sources
 Five by external sources, including three double-edge function
 Six by internal sources
• Subroutine stack up to 16 levels, including interrupts
• Four low-power dissipation modes
 Subactive mode
 Standby mode
 Watch mode
 Stop mode
• One external input for transition from stop mode to active mode
• Instruction cycle time: 1 µs (fOSC = 4 MHz at 1/4 division ratio), 0.5 µs (fOSC = 8 MHz at 1/4 division
ratio)
 1/4, 1/8, 1/16, or 1/32 division ratio can be selected
• Operation voltage
 2.7 V to 6.0 V (HD404638R, HD404639R, HD40A4638R, HD40A4639R)
 2.7 V to 5.5 V (HD407A4639R)
 With VCC = 2.2 V to 6.0 V, watch mode can be supported, and instructions can be executed in
subactive mode (not applicable to the HD407A4639R).
• Two operating modes
 MCU mode
 MCU/PROM mode (HD407A4639R)
Ordering Information
Type
Mask ROM
ZTAT
2
Instruction Cycle
Time (µs)
Product Name
Model Name
ROM (Words)
Package
HD404638R
HD404638RF
8,192
80-pin
plastic QFP
(FP-80B)
HD404639R
HD404639RF
16,384
0.5 (f OSC = 8 MHz at1/4 HD40A4638R
division ratio)
HD40A4638RF
8,192
HD40A4639R
HD40A4639RF
16,384
1 (fOSC = 4 MHz at 1/4
division ratio)
0.5 (f OSC = 8 MHz at 1/4 HD407A4639R
division ratio)
HD407A4639RF 16,384
HD404639R Series
VTref
VCC
TONER
TONEC
SEL
RC 0
RB 3
RB 2
RB 1
RB 0
RA 3
RA 2
RA 1
RA 0
R9 3
R9 2
Pin Arrangement
80 7978 7776 757473727170 69686766 65
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
FP-80B
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
R9 1
R9 0
R8 3
R8 2
R8 1
R8 0
R7 3
R7 2
R7 1
R7 0
R6 3
R6 2
R6 1
R6 0
R5 3 /SO2
R5 2 /SI 2
R5 1 /SCK2
R5 0
R4 3 /SO1
R4 2 /SI 1
R4 1 /SCK1
R4 0 /EVND
R3 3 /EVNB
R3 2 /TOD
25 2627 2829 303132333435 36373839 40
D12 /STOPC
D13 /INT0
R00 /INT1
R01 /INT2
R02 /INT3
R03 /INT4
R10
R11
R12
R13
R20
R21
R22
R23
R30 /TOB
R31 /TOC
RD0 /COMP0
RD1 /COMP1
RD2 /COMP2
RD3 /COMP3
RE0 /VC ref
TEST
OSC1
OSC2
RESET
X1
X2
GND
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
(Top view)
3
HD404639R Series
Pin Description
Item
Symbol
Pin Number I/O Function
Power
supply
VCC
79
—
Applies power voltage
GND
12
—
Connected to ground
Test
TEST
6
I
Used for factory testing only: Connect this pin to VCC
Reset
RESET
9
I
Resets the MCU
Oscillator
OSC 1
7
I
Input/output pins for the internal oscillator circuit:
Connect them to a ceramic oscillator, crystal, or connect
OSC 1 to an external oscillator circuit
OSC 2
8
O
X1
10
I
X2
11
O
D0–D 11
13–24
I/O Input/output pins addressed by individual bits; pins D 4–
D11 are high-current sink pins that can each supply up to
15 mA, D 0–D 3 are high-current source pins that can each
supply up to 10 mA
D12, D13
25, 26
I
R0 0–RC0
27–75
I/O Input/output pins addressable in 4-bit units
RD0–RD3,RE0
1–5
I
Input pins addressable in 4-bit units
Interrupt
INT0, INT1,
INT2–INT4
26–30
I
Input pins for external interrupts
Stop clear
STOPC
25
I
Input pin for transition from stop mode to active mode
Serial
interface
SCK 1, SCK 2
44, 48
I/O Serial interface clock input/output pin
SI 1, SI 2
45, 49
I
Serial interface receive data input pin
SO1, SO2
46, 50
O
Serial interface transmit data output pin
TOB, TOC, TOD 39–41
O
Timer output pins
EVNB, EVND
42, 43
I
Event count input pins
TONER
78
O
Output pin for DTMF row signals
TONEC
77
O
Output pin for DTMF column signals.
VT ref
80
—
Reference voltage pin for DTMF signals.
Voltage conditions being V CC ≥ VTref ≥ GND
I
Analog input pins for voltage comparator
Port
Timer
DTMF
Voltage
COMP0–COMP3 1–4
comparator
Division
rate
4
Used for a 32.768-kHz crystal for clock purposes. If not to
be used, fix the X1 pin to V CC and leave the X2 pin open.
Input pins addressable by individual bits
VC ref
5
—
Reference voltage pin for inputting the threshold voltage
of the analog input pin.
SEL
76
I
Input pin for selecting system clock division rate after
RESET input or after stop mode cancellation.
1/4 division rate: Connect it to V CC 1/32 division rate:
Connect it to GND
HD404639R Series
RESET
TEST
STOPC
OSC 1
OSC 2
X1
X2
SEL
VCC
GND
Block Diagram
System control
External
interrupt
W
(2 bit)
Timer
A
Timer
C
EVND
TOD
Timer
D
SI 1
SO 1
SCK 1
Serial
interface
1
SI 2
SO 2
SCK 2
Serial
interface
2
VCref
COMP0
COMP1
COMP2
COMP3
Comparator
VTref
TONER
TONEC
DTMF
SPX
(4 bit)
Y
(4 bit)
SPY
(4 bit)
ALU
CPU
ST
CA
(1 bit) (1 bit)
A
(4 bit)
B
(4 bit)
SP
(10 bit)
Insruction
decoder
PC
(14 bit)
ROM
(16,384 × 10 bit)
(8,192 × 10 bit)
RB port RA port R9 port R8 port R7 port R6 port R5 port R4 port R3 port R2 port R1 port R0 port
TOC
X
(4 bit)
Internal address bus
Timer
B
Internal data bus
EVNB
TOB
D port
RAM
(1,152 × 4 bit)
RD port
INT 0
INT 1
INT 2
INT 3
INT 4
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D 10
D 11
D 12
D 13
R0 0
R0 1
R0 2
R0 3
R1 0
R1 1
R1 2
R1 3
R2 0
R2 1
R2 2
R2 3
R3 0
R3 1
R3 2
R3 3
R4 0
R4 1
R4 2
R4 3
R5 0
R5 1
R5 2
R5 3
R6 0
R6 1
R6 2
R6 3
R7 0
R7 1
R7 2
R7 3
R8 0
R8 1
R8 2
R8 3
R9 0
R9 1
R9 2
R9 3
RA0
RA1
RA2
RA3
RB 0
RB 1
RB 2
RB 3
RC 0
RC port
RD 0
RD 1
RD 2
RD 3
RE port
RE 0
High-current
source pins
High-current
sink pins
5
HD404639R Series
Memory Map
ROM Memory Map
The ROM memory map is shown in figure 1 and described below.
0
$0000
Vector address
15
$000F
16
$0010
Zero-page subroutine
(64 words)
$003F
63
64
$0040
Pattern
(4,096 words)
$0FFF
4095
$1000
4096
Program
(8,192 words)
8191
0
JMPL instruction
1 (Jump to RESET, STOPC routine)
JMPL instruction
2
(Jump to INT0 routine)
3
JMPL instruction
4
(Jump to INT1 routine)
5
6
7
8
9
10
11
12
13
14
15
JMPL instruction
(Jump to timer A routine)
JMPL instruction
(Jump to timer B, INT2 routine)
JMPL instruction
(Jump to timer C, INT3 routine)
JMPL instruction
(Jump to timer D, INT4 routine)
JMPL instruction
(Jump to serial 1, serial 2 routine)
$0000
$0001
$0002
$0003
$0004
$0005
$0006
$0007
$0008
$0009
$000A
$000B
$000C
$000D
$000E
$000F
For HD404638R, HD40A4638R $1FFF
8192
$2000
Program
(16,384 words)
16383
For HD404639R, HD40A4639R,
HD407A4639R
$3FFF
Figure 1 ROM Memory Map
Vector Address Area ($0000–$000F): Reserved for JMPL instructions that branch to the start addresses
of the reset and interrupt routines. After MCU reset or an interrupt, program execution continues from the
vector address.
Zero-Page Subroutine Area ($0000–$003F): Reserved for subroutines. The program branches to a
subroutine in this area in response to the CAL instruction.
Pattern Area ($0000–$0FFF): Contains ROM data that can be referenced with the P instruction.
Program Area ($0000–$1FFF (HD404638R, HD40A4638R), $0000–$3FFF (HD404639R,
HD40A4639R, HD407A4639R)): Used for program coding.
6
HD404639R Series
RAM Memory Map
The MCU contains a 1,152-digit × 4-bit RAM area consisting of a memory register area, a data area, and a
stack area. In addition, an interrupt control bits area, special register area, and register flag area are mapped
onto the same RAM memory space as a RAM-mapped register area outside the above areas. The RAM
memory map is shown in figure 2 and described as follows.
RAM-Mapped Register Area ($000–$03F):
• Interrupt Control Bits Area ($000–$003)
This area is used for interrupt control bits (figure 3). These bits can be accessed only by RAM bit
manipulation instructions (SEM/SEMD, REM/REMD, and TM/TMD). However, note that not all the
instructions can be used for each bit. Limitations on using the instructions are shown in figure 4.
• Special Function Register Area ($004–$01E, $024–$03F)
This area is used as mode registers and data registers for external interrupts, serial interface 1, serial
interface 2, timer/counters, voltage comparator, and as data control registers for I/O ports. The
structure is shown in figures 2 and 5. These registers can be classified into three types: write-only (W),
read-only (R), and read/write (R/W). RAM bit manipulation instructions cannot be used for these
registers.
• Register Flag Area ($020–$023)
This area is used for the DTON, WDON, and other register flags and interrupt control bits (figure 3).
These bits can be accessed only by RAM bit manipulation instructions (SEM/SEMD, REM/REMD, and
TM/TMD). However, note that not all the instructions can be used for each bit. Limitations on using
the instructions are shown in figure 4.
Memory Register (MR) Area ($040–$04F): Consisting of 16 addresses, this area (MR0–MR15) can be
accessed by register-register instructions (LAMR and XMRA). The structure is shown in figure 6.
Data Area ($090–$2EF): Consists of 464 digits from $090 to $25F in two banks, which can be selected
by setting the bank register (V: $03F). Before accessing this area, set the bank register to the required
value (figure 7). The area from $260 to $2EF is accessed without setting the bank register.
Stack Area ($3C0–$3FF): Used for saving the contents of the program counter (PC), status flag (ST), and
carry flag (CA) at subroutine call (CAL or CALL instruction) and for interrupts. This area can be used as a
16-level nesting subroutine stack in which one level requires four digits. The data to be saved and the save
conditions are shown in figure 6.
The program counter is restored by either the RTN or RTNI instruction, but the status and carry flags can
only be restored by the RTNI instruction. Any unused space in this area is used for data storage.
7
HD404639R Series
0
$000
RAM-mapped registers
64
Memory registers (MR)
80
$040
$050
Not used
$090
144
Data (464 digits × 2)
V = 0 (bank 0)
V = 1 (bank 1)
*
$260
608
Data (144 digits)
752
960
$2F0
Not used
$3C0
Stack (64 digits)
$3FF
1023
$090
Data
(464 digits)
V=0
(bank = 0)
Data
(464 digits)
V=1
(bank = 1)
$25F
Note: * The data area has two banks:
bank 0 (V = 0) to bank 1 (V = 1)
R:
Read only
W:
Write only
R/W: Read/Write
Two registers are mapped
on the same area.
10
11
0
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
63
Interrupt control bits area
(PMRA)
Port mode register A
Serial mode register 1A (SM1A)
Serial data register 1 lower (SR1L)
Serial data register 1 upper (SR1U)
Timer mode register A
(TMA)
Timer mode register B1
(TMB1)
(TRBL/TWBL)
Timer B
(TRBU/TWBU)
(MIS)
Miscellaneous register
Timer mode register C1 (TMC1)
(TRCL/TWCL)
Timer C
(TRCU/TWCU)
Timer mode register D1 (TMD1)
(TRDL/TWDL)
Timer D
(TRDU/TWDU)
(TMB2)
Timer mode register B2
Timer mode register C2 (TMC2)
Timer mode register D2 (TMD2)
Compare control register (CCR)
Compare data register
(CDR)
(CER)
Compare enable register
TG mode register
(TGM)
(TGC)
TG control register
Serial mode register 2A (SM2A)
Serial mode register 2B (SM2B)
Serial data register 2 lower (SR2L)
Serial data register 2 upper (SR2U)
Not used
W
W
R/W
R/W
W
W
R/W
R/W
W
W
R/W
R/W
W
R/W
R/W
R/W
R/W
R/W
W
R
W
W
W
W
W
R/W
R/W
Register flag area
Port mode register B
Port mode register C
(PMRB)
(PMRC)
Detection edge select register 1 (ESR1)
Detection edge select register 2 (ESR2)
Serial mode register 1B
(SM1B)
System clock select register 1 (SSR1)
System clock select register 2 (SSR2)
Not used
Port D0 to D3 DCR
Port D4 to D 7 DCR
Port D8 to D11 DCR
Not used
Port R0 DCR
Port R1 DCR
Port R2 DCR
Port R3 DCR
Port R4 DCR
Port R5 DCR
Port R6 DCR
Port R7 DCR
Port R8 DCR
Port R9 DCR
Port RA DCR
Port RB DCR
Port RC DCR
Not used
V register
W
W
W
W
W
W
W
$000
$003
$004
$005
$006
$007
$008
$009
$00A
$00B
$00C
$00D
$00E
$00F
$010
$011
$012
$013
$014
$015
$016
$017
$018
$019
$01A
$01B
$01C
$01D
$01E
$01F
$020
$023
$024
$025
$026
$027
$028
$029
$02A
$02B
(DCD0)
(DCD1)
(DCD2)
W
W
W
(DCR0)
(DCR1)
(DCR2)
(DCR3)
(DCR4)
(DCR5)
(DCR6)
(DCR7)
(DCR8)
(DCR9)
(DCRA)
(DCRB)
(DCRC)
W
W
W
W
W
W
W
W
W
W
W
W
W
$02C
$02D
$02E
$02F
$030
$031
$032
$033
$034
$035
$036
$037
$038
$039
$03A
$03B
$03C
R/W
$03F
Timer read register B lower (TRBL) R Timer write register B lower (TWBL) W $00A
Timer read register B upper (TRBU) R Timer write register B upper (TWBU) W $00B
14 Timer read register C lower (TRCL) R Timer write register C lower (TWCL) W $00E
15 Timer read register C upper (TRCU) R Timer write register C upper (TWCU) W $00F
17 Timer read register D lower (TRDL) R Timer write register D lower (TWDL) W $011
18 Timer read register D upper (TRDU) R Timer write register D upper (TWDU) W $012
Figure 2 RAM Memory Map
8
HD404639R Series
Bit 3
Bit 2
Bit 1
Bit 0
0
IM0
(IM of INT0)
IF0
(IF of INT0)
RSP
(Reset SP bit)
IE
(Interrupt
enable flag)
$000
1
IMTA
(IM of timer A)
IFTA
(IF of timer A)
IM1
(IM of INT1)
IF1
(IF of INT1)
$001
2
IMTC
(IM of timer C)
IFTC
(IF of timer C)
IMTB
(IM of timer B)
IFTB
(IF of timer B)
$002
3
IMS1
(IM of serial
interface 1)
IFS1
(IF of serial
interface 1)
IMTD
(IM of timer D)
IFTD
(IF of timer D)
$003
Interrupt control bits area
Bit 3
Bit 2
Bit 1
Bit 0
32
DTON
(Direct transfer
on flag)
Not used
WDON
(Watchdog
on flag)
LSON
(Low speed
on flag)
$020
33
RAME
(RAM enable
flag)
Not used
ICEF
(Input capture
error flag)
ICSF
(Input capture
status flag)
$021
34
IM3
(IM of INT3)
IF3
(IF of INT3)
IM2
(IM of INT2)
IF2
(IF of INT2)
$022
35
IMS2
(IM of serial
interface 2)
IFS2
(IF of serial
interface 2)
IM4
(IM of INT 4 )
IF4
(IF of INT 4 )
$023
IF:
IM:
IE:
SP:
Interrupt request flag
Interrupt mask
Interrupt enable flag
Stack pointer
Register flag area
Figure 3 Configuration of Interrupt Control Bits and Register Flag Areas
IE
IM
LSON
IF
ICSF
ICEF
RAME
RSP
WDON
DTON
Not used
SEM/SEMD
REM/REMD
TM/TMD
Allowed
Allowed
Allowed
Not executed
Allowed
Allowed
Not executed
Allowed
Not executed in active mode
Used in subactive mode
Not executed
Allowed
Not executed
Inhibited
Inhibited
Allowed
Allowed
Not executed
Inhibited
Note: WDON is reset by MCU reset or by STOPC enable for stop mode cancellation.
DTON is always reset in active mode.
If the TM or TMD instruction is executed for the inhibited bits or non-existing bits,
the value in ST becomes invalid.
Figure 4 Usage Limitations of RAM Bit Manipulation Instructions
9
HD404639R Series
Bit 3
Bit 2
$000
$003
Bit 0
Bit 1
Interrupt control bits area
PMRA $004
R52/SI2
SM1A $005
R41/SCK1
R53/SO2
R42/SI1
R43/SO1
Serial transmit clock speed selection 1
SR1L $006
Serial data register 1 (lower digit)
SR1U $007
Serial data register 1 (upper digit)
TMA $008
*1
TMB1 $009
*2
Clock source selection (timer A)
Clock source selection (timer B)
Timer B register (lower digit)
TRBL/TWBL $00A
Timer B register (upper digit)
TRBU/TWBU $00B
MIS $00C
*3
TMC1 $00D
*2
SO1 PMOS control Interrupt frame period selection
Clock source selection (timer C)
Timer C register (lower digit)
TRCL/TWCL $00E
Timer C register (upper digit)
TRCU/TWCU $00F
TMD1 $010
*2
Clock source selection (timer D)
Timer D register (lower digit)
TRDL/TWDL $011
Timer D register (upper digit)
TRDU/TWDU $012
TMB2 $013
TMC2 $014
TMD2 $015
Not used
Not used
*4
CDR $017
TGM $019
TGC $01A
Timer-B output mode selection
Timer-C output mode selection
Timer-D output mode selection
Internal reference voltages level
CCR $016
CER $018
Not used
*5
Result of each analog input comparison
*6
*7
TONEC output frequency
*8
*9
SM2A $01B
R51/SCK2
SM2B $01C
Not used
TONER output frequency
DTMF enable
Not used
Serial transmit clock speed selection 2
*10
*11
SO PMOS control
2
SR2L $01D
Serial data register 2 (lower digit)
SR2U $01E
Serial data register 2 (upper digit)
Not used
$020
Register flag area
$023
PMRB $024
R03/INT4
R02/INT3
R01/INT2
R00/INT1
PMRC $025
D13/INT0
D12/STOPC
R40/EVND
R33/EVNB
ESR1 $026
INT3 detection edge selection INT2 detection edge selection
ESR2 $027 EVND detection edge selection INT4 detection edge selection
*12
*13
Not used
Not used
SM1B $028
*14
*15
System clock selection
SSR1 $029
System clock selection
System clock division rate
SSR2 $02A
Not used
DCD0 $02C
Port D3 DCR Port D2 DCR
Port D1 DCR Port D0 DCR
DCD1 $02D
Port D7 DCR Port D6 DCR
Port D5 DCR Port D4 DCR
DCD2 $02E Port D11 DCR Port D10 DCR Port D9 DCR Port D8 DCR
Not used
DCR0 $030
Port R0 3 DCR Port R0 2 DCR Port R0 1 DCR Port R0 0 DCR
DCR1 $031
Port R13 DCR Port R1 2 DCR Port R1 1 DCR Port R1 0 DCR
DCR2 $032
Port R2 3 DCR Port R2 2 DCR Port R2 1 DCR Port R2 0 DCR
DCR3 $033
Port R3 3 DCR Port R3 2 DCR Port R3 1 DCR Port R3 0 DCR
DCR4 $034
Port R4 3 DCR Port R4 2 DCR Port R4 1 DCR Port R4 0 DCR
DCR5 $035
Port R5 3 DCR Port R5 2 DCR Port R5 1 DCR Port R5 0 DCR
DCR6 $036
Port R6 3 DCR Port R6 2 DCR Port R6 1 DCR Port R6 0 DCR
DCR7 $037
Port R7 3 DCR Port R7 2 DCR Port R7 1 DCR Port R7 0 DCR
DCR8 $038
Port R8 3 DCR Port R8 2 DCR Port R8 1 DCR Port R8 0 DCR
DCR9 $039
Port R9 3 DCR Port R9 2 DCR Port R9 1 DCR Port R9 0 DCR
DCRA $03A
Port RA 3 DCR Port RA2 DCR Port RA 1 DCR Port RA0 DCR
DCRB $03B
Port RB 3 DCR Port RB2 DCR Port RB 1 DCR Port RB0 DCR
DCRC $03C
Not used
Not used
Not used
Not used
V $03F
Not used
Not used
Not used
Port RC0 DCR
*16
Notes:
1. Timer-A/time-base
2. Auto-reload on/off
3. Pull-up MOS control
4. Input capture selection
5. Comparator switch
6. Reference voltage selection
7. Comparator selection
8. TONEC output control
9. TONER output control
10. SO 2 output control in idle states
11. Serial clock source selection 2
12. SO 1 output level control in idle states
13. Transmit clock source selection 1
14. 32-kHz oscillation stop
15. 32-kHz oscillation division ratio
16. Bank 0 to bank 1 selection
Figure 5 Special Function Register Area
10
HD404639R Series
Memory registers
MR(0) $040
64
MR(1) $041
65
MR(2) $042
66
MR(3)
$043
67
MR(4)
$044
68
MR(5)
$045
69
MR(6)
$046
70
MR(7)
$047
71
MR(8)
$048
72
MR(9)
$049
73
MR(10) $04A
74
MR(11) $04B
75
MR(12) $04C
76
MR(13) $04D
77
MR(14) $04E
78
MR(15) $04F
79
Stack area
Level 16
Level 15
Level 14
Level 13
Level 12
Level 11
Level 10
Level 9
Level 8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
1023 Level 1
960
$3C0
$3FF
Bit 3
Bit 2
Bit 1
Bit 0
1020
ST
PC13
PC 12
PC11
$3FC
1021
PC 10
PC9
PC 8
PC7
$3FD
1022
CA
PC6
PC 5
PC4
$3FE
1023
PC 3
PC2
PC 1
PC0
$3FF
PC13 –PC0 : Program counter
ST: Status flag
CA: Carry flag
Figure 6 Configuration of Memory Registers and Stack Area, and Stack Position
Bank register (V: $03F)
Bit
3
2
1
Initial value
—
—
—
0
Read/Write
—
—
—
R/W
Bit name
V0
Not used Not used Not used
0
V0
Bank area selection
0
Bank 0 is selected
1
Bank 1 is selected
Note: After reset, the value in the bank register is 0, and therefore bank 0 is
selected.
Figure 7 Bank Register (V)
11
HD404639R Series
Functional Description
Registers and Flags
The MCU has nine registers and two flags for CPU operations. They are shown in figure 8 and described
below.
3
Accumulator
0
(A)
Initial value: Undefined, R/W
3
B register
Initial value: Undefined, R/W
0
(B)
1
W register
Initial value: Undefined, R/W
0
(W)
3
X register
Initial value: Undefined, R/W
Y register
Initial value: Undefined, R/W
SPX register
Initial value: Undefined, R/W
0
(X)
3
0
(Y)
3
0
(SPX)
3
SPY register
Initial value: Undefined, R/W
0
(SPY)
0
Carry
Initial value: Undefined, R/W
(CA)
0
Status
Initial value: 1, no R/W
(ST)
13
Program counter
Initial value: 0,
no R/W
0
(PC)
9
Stack pointer
Initial value: $3FF, no R/W
1
5
1
1
1
0
(SP)
Figure 8 Registers and Flags
Accumulator (A), B Register (B): Four-bit registers used to hold the results from the arithmetic logic unit
(ALU) and transfer data between memory, I/O, and other registers.
W Register (W), X Register (X), Y Register (Y): Two-bit (W) and four-bit (X and Y) registers used for
indirect RAM addressing. The Y register is also used for D-port addressing.
12
HD404639R Series
SPX Register (SPX), SPY Register (SPY): Four-bit registers used to supplement the X and Y registers.
Carry Flag (CA): One-bit flag that stores any ALU overflow generated by an arithmetic operation. CA is
affected by the SEC, REC, ROTL, and ROTR instructions. A carry is pushed onto the stack during an
interrupt and popped from the stack by the RTNI instruction—but not by the RTN instruction.
Status Flag (ST): One-bit flag that latches any overflow generated by an arithmetic or compare
instruction, not-zero decision from the ALU, or result of a bit test. ST is used as a branch condition of the
BR, BRL, CAL, and CALL instructions. The contents of ST remain unchanged until the next arithmetic,
compare, or bit test instruction is executed, but become 1 after the BR, BRL, CAL, or CALL instruction is
read, regardless of whether the instruction is executed or skipped. The contents of ST are pushed onto the
stack during an interrupt and popped from the stack by the RTNI instruction—but not by the RTN
instruction.
Program Counter (PC): 14-bit binary counter that points to the ROM address of the instruction being
executed.
Stack Pointer (SP): Ten-bit pointer that contains the address of the stack area to be used next. The SP is
initialized to $3FF by MCU reset. It is decremented by 4 when data is pushed onto the stack, and
incremented by 4 when data is popped from the stack. The top four bits of the SP are fixed at 1111, so a
stack can be used up to 16 levels.
The SP can be initialized to $3FF in another way: by resetting the RSP bit with the REM or REMD
instruction.
Reset
The MCU is reset by inputting a high-level voltage to the RESET pin. At power-on or when stop mode is
cancelled, RESET must be high for at least one tRC to enable the oscillator to stabilize. During operation,
RESET must be high for at least two instruction cycles.
Initial values after MCU reset are listed in table 1.
13
HD404639R Series
Table 1 Initial Values After MCU Reset
Item
Abbr.
Initial Value Contents
Program counter
(PC)
$0000
Indicates program execution point
from start address of ROM area
Status flag
(ST)
1
Enables conditional branching
Stack pointer
(SP)
$3FF
Stack level 0
Interrupt enable flag
(IE)
0
Inhibits all interrupts
Interrupt request flag
(IF)
0
Indicates there is no interrupt
request
Interrupt mask
(IM)
1
Prevents (masks) interrupt
requests
Port data register
(PDR)
All bits 1
Enables output at level 1
Data control register
(DCD0–DCD2)
All bits 0
Turns output buffer off (to high
impedance)
(DCR0–DCRC)
All bits 0
Port mode register A
(PMRA)
0000
Refer to description of port mode
register A
Port mode register B
(PMRB)
0000
Refer to description of port mode
register B
Port mode register C
bits 3, 1, 0
(PMRC3, PMRC1, 000
PMRC0)
Refer to description of port mode
register C
Detection edge select
register 1
(ESR1)
0000
Disables edge detection
Detection edge select
register 2
(ESR2)
0000
Disables edge detection
Timer/
counters,
Timer mode register A
(TMA)
0000
Refer to description of timer mode
register A
serial
interface
Timer mode register B1 (TMB1)
0000
Refer to description of timer mode
register B1
Timer mode register B2 (TMB2)
- - 00
Refer to description of timer mode
register B2
Timer mode register C1 (TMC1)
0000
Refer to description of timer mode
register C1
Timer mode register C2 (TMC2)
- 000
Refer to description of timer mode
register C2
Timer mode register D1 (TMD1)
0000
Refer to description of timer mode
register D1
Timer mode register D2 (TMD2)
0000
Refer to description of timer mode
register D2
Interrupt
flags/mask
I/O
Notes: 1. The statuses of other registers and flags after MCU reset are shown in the following table.
2. X indicates invalid value. – indicates that the bit does not exist.
14
HD404639R Series
Item
Abbr.
Initial
Value
Contents
Timer/
counters,
Serial mode register 1A
(SM1A)
0000
Refer to description of serial mode
register 1A
serial
interface
Serial mode register 1B
(SM1B)
- - X0
Refer to description of serial mode
register 1B
Serial mode register 2A
(SM2A)
0000
Refer to description of serial mode
register 2A
Serial mode register 2B
(SM2B)
- 0X0
Refer to description of serial mode
register 2B
Prescaler S
(PSS)
$000
—
Prescaler W
(PSW)
$00
—
Timer counter A
(TCA)
$00
—
Timer counter B
(TCB)
$00
—
Timer counter C
(TCC)
$00
—
Timer counter D
(TCD)
$00
—
Timer write register B
(TWBU, TWBL) $X0
—
Timer write register C
(TWCU, TWCL) $X0
—
Timer write register D
(TWDU, TWDL) $X0
—
000
—
Comparator Compare control register (CCR)
0000
Refer to description of voltage comparator
Compare enable register (CER)
0000
Refer to description of voltage comparator
(LSON)
0
Refer to description of operating modes
Watchdog timer on flag
(WDON)
0
Refer to description of timer C
Direct transfer on flag
(DTON)
0
Refer to description of operating modes
Input capture status flag
(ICSF)
0
Refer to description of timer D
Input capture error flag
(ICEF)
0
Refer to description of timer D
Miscellaneous register
(MIS)
0000
Refer to description of operating modes,
and oscillator circuit
System clock select
register 1 bits 2–0
(SSR12–
SSR10)
000
Refer to description of operating modes,
and oscillator circuit
System clock select
register 2
(SSR2)
0000
Bank register
(V)
---0
Octal counter
Bit register Low speed on flag
Others
Refer to description of RAM memory map
Notes: 1. The statuses of other registers and flags after MCU reset are shown in the following table.
2. X indicates invalid value. – indicates that the bit does not exist.
15
HD404639R Series
Item
Abbr.
Carry flag
(CA)
Accumulator
(A)
B register
(B)
W register
(W)
X/SPX register
(X/SPX)
Y/SPY register
(Y/SPY)
Serial data register
(SRL, SRU)
RAM
RAM enable flag
Status After
Cancellation of
Stop Mode by
MCU Reset
Status After all
Other Types of
Reset
Pre-stop-mode values are not guaranteed; Pre-stop-mode
values must be initialized by program
values are not
guaranteed; values
must be initialized by
program
Pre-stop-mode values are retained
(RAME)
Port mode register C bit 2 (PMRC2)
System clock select
register 1 bit 3
Status After
Cancellation of Stop
Mode by STOPC
Input
1
0
0
Pre-stop-mode values 0
are retained
0
(SSR13)
Interrupts
The MCU has 11 interrupt sources: five external signals (INT0 , INT1, INT 2 , INT3 , INT4 ), four
timer/counters (timers A, B, C, and D), and two serial interfaces (serial interface 1, serial interface 2).
An interrupt request flag (IF), interrupt mask (IM), and vector address are provided for each interrupt
source, and an interrupt enable flag (IE) controls the entire interrupt process.
Some vector addresses are shared by two different interrupts. They are timer B and INT 2, timer C and
INT 3, timer D and INT4, and serial interface 1 and serial interface 2. So the type of request that has
occurred must be checked at the beginning of interrupt processing.
Interrupt Control Bits and Interrupt Processing: Locations $000 to $003 and $022 to $023 in RAM are
reserved for the interrupt control bits which can be accessed by RAM bit manipulation instructions.
The interrupt request flag (IF) cannot be set by software. MCU reset initializes the interrupt enable flag
(IE) and the IF to 0 and the interrupt mask (IM) to 1.
A block diagram of the interrupt control circuit is shown in figure 9, interrupt priorities and vector
addresses are listed in table 2, and interrupt processing conditions for the 11 interrupt sources are listed in
table 3.
16
HD404639R Series
An interrupt request occurs when the IF is set to 1 and the IM is set to 0. If the IE is 1 at that point, the
interrupt is processed. A priority programmable logic array (PLA) generates the vector address assigned to
that interrupt source.
The interrupt processing sequence is shown in figure 10 and an interrupt processing flowchart is shown in
figure 11. After an interrupt is acknowledged, the previous instruction is completed in the first cycle. The
IE is reset in the second cycle, the carry, status, and program counter values are pushed onto the stack
during the second and third cycles, and the program jumps to the vector address to execute the instruction
in the third cycle.
Program the JMPL instruction at each vector address to branch the program to the start address of the
interrupt program, and reset the IF by a software instruction within the interrupt program.
Table 2 Vector Addresses and Interrupt Priorities
Reset/Interrupt
Priority
Vector Address
RESET, STOPC*
—
$0000
INT0
1
$0002
INT1
2
$0004
Timer A
3
$0006
Timer B, INT2
4
$0008
Timer C, INT3
5
$000A
Timer D, INT4
6
$000C
Serial 1 and 2
7
$000E
Note: * The STOPC interrupt request is valid only in stop mode
Table 3 Interrupt Processing and Activation Conditions
Interrupt Source
INT0
INT1
Timer A
Timer B
or INT2
Timer C or Timer D or Serial 1 or
INT3
INT4
Serial 2
1
1
1
1
1
1
1
IF0 IM0
1
0
0
0
0
0
0
.
*
1
0
0
0
0
0
*
*
1
0
0
0
0
*
*
*
1
0
0
0
*
*
*
*
1
0
0
*
*
*
*
*
1
0
*
*
*
*
*
*
1
Interrupt Control Bit
IE
.
IF1 IM1
.
IFTA IMTA
.
.
.
.
.
.
IFTB IMTB + IF2 IM2
IFTC IMTC + IF3 IM3
IFTD IMTD + IF4 IM4
.
.
IFS1 IMS1 + IFS2 IMS2
Note: * Can be either 0 or 1. Their values have no effect on operation.
17
HD404639R Series
$ 000,0
IE
INT0 interrupt
Sequence control
• Push PC/CA/ST
• Reset IE
• Jump to vector
address
$ 000,2
IFO
$ 000,3
IMO
Vector
address
Priority control logic
INT1 interrupt
$ 001,0
IF1
$ 001,1
IM1
Timer A interrupt
$ 001,2
IFTA
$ 001,3
IMTA
Timer B interrupt
Timer C interrupt
Timer D interrupt
$ 002,0
IFTB
$ 022,0
IF2
INT2 interrupt
$ 002,1
IMTB
$ 022,1
IM2
$ 002,2
IFTC
$ 022,2
IF3
INT3 interrupt
$ 002,3
IMTC
$ 022,3
IM3
$ 003,0
IFTD
$ 023,0
$ 003,1
$ 023,1
IF4
IMTD
IM4
$ 003,2
Serial 1 interrupt
$ 023,2
Serial 2 interrupt
IFS2
IFS1
$ 003,3
$ 023,3
IMS2
IMS1
Note: $m,n is RAM address $m, bit number n.
Figure 9 Interrupt Control Circuit
18
INT4 interrupt
HD404639R Series
Instruction cycles
1
2
3
4
5
6
Instruction
execution *
Interrupt
acceptance
Stacking
IE reset
Vector address
generation
Execution of JMPL
instruction at vector address
Note: * The stack is accessed and the IE reset after the instruction
is executed, even if it is a two-cycle instruction.
Execution of
instruction at
start address
of interrupt
routine
Figure 10 Interrupt Processing Sequence
19
HD404639R Series
Power on
RESET = 1?
Yes
No
Interrupt
request?
No
Yes
No
IE = 1?
Yes
Reset MCU
Accept interrupt
Execute instruction
IE ← 0
Stack ← (PC)
Stack ← (CA)
Stack ← (ST)
PC ←(PC) + 1
PC← $0002
Yes
INT0
interrupt?
No
PC← $0004
Yes
INT1
interrupt?
No
PC← $0006
Yes
Timer-A
interrupt?
No
PC← $0008
Yes
Timer-B/INT2
interrupt?
No
PC ← $000A
Yes
PC ← $000C
Yes
Timer-C/INT3
interrupt?
No
PC ← $000E
(Serial 1, serial 2
interrupt)
Figure 11 Interrupt Processing Flowchart
20
Timer-D/INT 4
interrupt?
No
HD404639R Series
Interrupt Enable Flag (IE: $000, Bit 0): Controls the entire interrupt process. It is reset by the interrupt
processing and set by the RTNI instruction, as listed in table 4.
Table 4 Interrupt Enable Flag (IE: $000, Bit 0)
IE
Interrupt Enabled/Disabled
0
Disabled
1
Enabled
External Interrupts (INT0, INT1, INT2–INT4): Five external interrupt signals.
External Interrupt Request Flags (IF0–IF4: $000, $001, $022, $023): IF0 and IF1 are set at the falling
edge of signals input to INT0 and INT1, and IF2–IF4 are set at the rising or falling edge of signals input to
INT 2–INT 4, as listed in table 5. The INT2–INT4 interrupt edges are selected by the detection edge select
registers (ESR1, ESR2: $026, $027) as shown in figures 12 and 13.
Table 5 External Interrupt Request Flags (IF0–IF4: $000, $001, $022, $023)
IF0–IF4
Interrupt Request
0
No
1
Yes
Detection edge selection register 1 (ESR1: $026)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
ESR13
ESR12
ESR11
ESR10
Bit name
INT3 detection edge
ESR13
ESR12
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
INT2 detection edge
ESR11
ESR10
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
Note: * Both falling and rising edges are detected.
Figure 12 Detection Edge Selection Register 1 (ESR1)
21
HD404639R Series
Detection edge selection register 2 (ESR2: $027)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
ESR23
ESR22
ESR21
ESR20
Bit name
EVND detection edge
ESR23
ESR22
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
INT 4 detection edge
ESR21
ESR20
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
Note: * Both falling and rising edges are detected.
Figure 13 detection Edge Selection Register 2 (ESR2)
External Interrupt Masks (IM0–IM4: $000, $001, $022, $023): Prevent (mask) interrupt requests
caused by the corresponding external interrupt request flags, as listed in table 6.
Table 6 External Interrupt Masks (IM0–IM4: $000, $001, $022, $023)
IM0–IM4
Interrupt Request
0
Enabled
1
Disabled (masked)
Timer A Interrupt Request Flag (IFTA: $001, Bit 2): Set by overflow output from timer A, as listed in
table 7.
Table 7 Timer A Interrupt Request Flag (IFTA: $001, Bit 2)
IFTA
Interrupt Request
0
No
1
Yes
Timer A Interrupt Mask (IMTA: $001, Bit 3): Prevents (masks) an interrupt request caused by the
timer A interrupt request flag, as listed in table 8.
22
HD404639R Series
Table 8 Timer A Interrupt Mask (IMTA: $001, Bit 3)
IMTA
Interrupt Request
0
Enabled
1
Disabled (masked)
Timer B Interrupt Request Flag (IFTB: $002, Bit 0): Set by overflow output from timer B, as listed in
table 9.
Table 9 Timer B Interrupt Request Flag (IFTB: $002, Bit 0)
IFTB
Interrupt Request
0
No
1
Yes
Timer B Interrupt Mask (IMTB: $002, Bit 1): Prevents (masks) an interrupt request caused by the
timer B interrupt request flag, as listed in table 10.
Table 10 Timer B Interrupt Mask (IMTB: $002, Bit 1)
IMTB
Interrupt Request
0
Enabled
1
Disabled (masked)
Timer C Interrupt Request Flag (IFTC: $002, Bit 2): Set by overflow output from timer C, as listed in
table 11.
Table 11 Timer C Interrupt Request Flag (IFTC: $002, Bit 2)
IFTC
Interrupt Request
0
No
1
Yes
Timer C Interrupt Mask (IMTC: $002, Bit 3): Prevents (masks) an interrupt request caused by the
timer C interrupt request flag, as listed in table 12.
Table 12 Timer C Interrupt Mask (IMTC: $002, Bit 3)
IMTC
Interrupt Request
0
Enabled
1
Disabled (masked)
23
HD404639R Series
Timer D Interrupt Request Flag (IFTD: $003, Bit 0): Set by overflow output from timer D, or by the
rising or falling edge of signals input to EVND when the input capture function is used, as listed in table
13.
Table 13 Timer D Interrupt Request Flag (IFTD: $003, Bit 0)
IFTD
Interrupt Request
0
No
1
Yes
Timer D Interrupt Mask (IMTD: $003, Bit 1): Prevents (masks) an interrupt request caused by the
timer D interrupt request flag, as listed in table 14.
Table 14 Timer D Interrupt Mask (IMTD: $003, Bit 1)
IMTD
Interrupt Request
0
Enabled
1
Disabled (masked)
Serial Interrupt Request Flags (IFS1: $003, Bit 2; IFS2: $023, Bit 2): Set when data transfer is
completed or when data transfer is suspended, as listed in table 15.
Table 15 Serial Interrupt Request Flag (IFS1: $003, Bit 2; IFS2: $023, Bit 2)
IFS1, IFS2
Interrupt Request
0
No
1
Yes
Serial Interrupt Masks (IMS1: $003, Bit 3; IMS2: $023, Bit 3): Prevents (masks) an interrupt request
caused by the serial interrupt request flag, as listed in table 16.
Table 16 Serial Interrupt Mask (IMS1: $003, Bit 3; IMS2: $023, Bit 3)
IMS1, IMS2
Interrupt Request
0
Enabled
1
Disabled (masked)
24
HD404639R Series
Operating Modes
The MCU has five operating modes as shown in table 17. The operations in each mode are listed in tables
18 and 19. Transitions between operating modes are shown in figure 14.
Table 17 Operating Modes and Clock Status
Mode Name
Active
Cancellation
method
Stop
Watch
Subactive
SBY
RESET
instruction
cancellation,
interrupt
request
STOPC
cancellation in
stop mode,
STOP/SBY
instruction in
subactive
mode (when
direct transfer
is selected)
INT0 or timer A
STOP
STOP
instruction when instruction when interrupt request
TMA3 = 0
TMA3 = 1
from watch
mode when
STOP/SBY
LSON = 1
instruction in
OP
OP
Stopped
Stopped
Stopped
Subsystem OP
oscillator
OP
OP *1
OP
OP
RESET
input,
interrupt
request
RESET input,
RESET input,
RESET input,
STOPC input in INT0 or timer A STOP/SBY
stop mode
interrupt request instruction
Activation
method
Status
Standby
System
oscillator
RESET input,
STOP/SBY
instruction
subactive mode
(when direct
transfer is not
selected)
Notes: OP implies in operation
1. Operating or stopping the oscillator can be selected by setting bit 3 of system clock select
register 1 (SSR1: $029).
25
HD404639R Series
Table 18 Operations in Low-Power Dissipation Modes
Function
Stop Mode
Watch Mode
Standby Mode
Subactive Mode
CPU
Reset
Retained
Retained
OP
RAM
Retained
Retained
Retained
OP
Timer A
Reset
OP
OP
OP
Timer B
Reset
Stopped
OP
OP
Timer C
Reset
Stopped
OP
OP
Timer D
Reset
Stopped
OP
OP
2
Serial interface 1, 2
Reset
Stopped*
OP
OP
DTMF
Reset
Reset
OP
Reset
Comparator
Reset
Stopped
Stopped
OP
Retained
Retained
OP
I/O
Reset*
1
Notes: OP implies in operation
1. Output pins are at high impedance.
2. Transmission/reception is activated if a clock is input in external clock mode. However, all
interrupts stop.
Table 19 I/O Status in Low-Power Dissipation Modes
Output
Input
Standby mode, watch
mode
Stop mode
Active mode, subactive
mode
D0–D 11
Retained
High impedance
Input enabled
D12–D 13 ,
—
—
Input enabled
Retained or output of
peripheral functions
High impedance
Input enabled
RD0–RD3,
RE 0
R0 0–RC1
26
HD404639R Series
Reset by
RESET input or
by watchdog timer
Stop mode
(TMA3 = 0, SSR13 = 0)
RAME = 0
RAME = 1
RESET1
RESET2
STOPC
STOPC
STOP
Oscillate
Oscillate
Stop
fcyc
fcyc
Stop
Oscillate
Stop
Stop
Stop
Active
mode
Standby mode
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
SBY
Interrupt
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Oscillate
Oscillate
fcyc
fcyc
fcyc
(TMA3 = 0, SSR13 = 1)
STOP
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Stop
Stop
Stop
Stop
Stop
(TMA3 = 0)
Watch mode
(TMA3 = 1)
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Oscillate
Oscillate
Stop
fW
fcyc
SBY
Interrupt
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Oscillate
Oscillate
fcyc
fW
fcyc
(TMA3 = 1, LSON = 0)
STOP
INT0,
timer A*1
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Stop
Oscillate
Stop
fW
Stop
*3
fOSC:
fX:
Main oscillation frequency
Suboscillation frequency
for time-base
fOSC/4 or fOSC/8 or
fcyc:
f OSC/16 or fOSC/32
(software selectable)
fSUB:
fX/8 or fX/4
(software selectable)
fW:
fX/8
ø CPU : System clock
ø CLK : Clock for time-base
ø PER : Clock for other
peripheral functions
LSON: Low speed on flag
DTON: Direct transfer on flag
*2
Subactive
mode
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
STOP
Stop
Oscillate
fSUB
fW
fSUB
Notes: 1.
2.
3.
4.
*4
INT0,
timer A*1
(TMA3 = 1, LSON = 1)
fOSC:
fX:
ø CPU :
ø CLK :
ø PER :
Stop
Oscillate
Stop
fW
Stop
Interrupt source
STOP/SBY (DTON = 1, LSON = 0)
STOP/SBY (DTON = 0, LSON = 0)
STOP/SBY (DTON = Don’t care, LSON = 1)
Figure 14 MCU Status Transitions
27
HD404639R Series
Active Mode: All MCU functions operate according to the clock generated by the system oscillators OSC1
and OSC2.
Standby Mode: In standby mode, the oscillators continue to operate, but the clocks related to instruction
execution stop. Therefore, the CPU operation stops, but all RAM and register contents are retained, and the
D or R port status, when set to output, is maintained. Peripheral functions such as interrupts, timers, and
serial interface continue to operate. The power dissipation in this mode is lower than in active mode
because the CPU stops.
The MCU enters standby mode when the SBY instruction is executed in active mode.
Standby mode is terminated by a RESET input or an interrupt request. If it is terminated by RESET input,
the MCU is reset as well. After an interrupt request, the MCU enters active mode and executes the next
instruction after the SBY instruction. If the interrupt enable flag is 1, the interrupt is then processed; if it is
0, the interrupt request is left pending and normal instruction execution continues. A flowchart of
operation in standby mode is shown in figure 15.
Stop Mode: In stop mode, all MCU operations stop and RAM data is retained. Therefore, the power
dissipation in this mode is the least of all modes. The OSC 1 and OSC2 oscillator stops. For the X1 and X2
oscillator to operate or stop can be selected by setting bit 3 of system clock select register 1 (SSR1: $029;
operating: SSR13 = 0, stop: SSR13 = 1) (figure 24). The MCU enters stop mode if the STOP instruction is
executed in active mode when bit 3 of timer mode register A (TMA: $008) is set to 0 (TMA3 = 0) (figure
41).
Stop mode is terminated by a RESET input or a STOPC input as shown in figure 16. RESET or STOPC
must be applied for at least one t RC to stabilize oscillation (refer to the AC Characteristics section). When
the MCU restarts after stop mode is cancelled, all RAM contents before entering stop mode are retained,
but the accuracy of the contents of the accumulator, B register, W register, X/SPX register, Y/SPY register,
carry flag, and serial data register cannot be guaranteed.
Watch Mode: In watch mode, the clock function (timer A) using the X1 and X2 oscillator operates but
other function operations stop. Therefore, the power dissipation in this mode is the second least to stop
mode, and this mode is convenient when only clock display is used. In this mode, the OSC 1 and OSC2
oscillator stops, but the X1 and X2 oscillator operates. The MCU enters watch mode if the STOP
instruction is executed in active mode when TMA3 = 1, or if the STOP or SBY instruction is executed in
subactive mode.
Watch mode is terminated by a RESET input or a timer-A/INT0 interrupt request. For details of RESET
input, refer to the Stop Mode section. When terminated by a timer-A/INT0 interrupt request, the MCU
enters active mode if LSON is 0, or subactive mode if LSON is 1. After an interrupt request is generated,
the time required to enter active mode is tRC for a timer A interrupt, and TX (where T + tRC < TX < 2T + tRC)
for an INT0 interrupt, as shown in figures 17 and 18.
Operation during mode transition is the same as that at standby mode cancellation (figure 15).
28
HD404639R Series
Stop
Standby
Watch
Oscillator: Stop
Suboscillator: Active/Stop
Peripheral clocks: Stop
All other clocks: Stop
Oscillator: Active
Peripheral clocks: Active
All other clocks: Stop
Oscillator: Stop
Suboscillator: Active
Peripheral clocks: Stop
All other clocks: Stop
No
RESET = 1?
Yes
No
RESET = 1?
Yes
IF0 • IM0 = 1?
No
No
STOPC = 0?
Yes
IF1 • IM1 = 1?
No
Yes
Yes
IFTA • IMTA
= 1?
Yes
RAME = 1
No
IFTB •
IMTB + IF2 •
IM2 = 1?
RAME = 0
No
Yes
IFTC •
IMTC + IF3 •
IM3 = 1?
Yes
No
IFTD •
IMTD + IF4 •
IM4 = 1?
Yes
(SBY
only)
Restart
processor clocks
(SBY
only)
(SBY
only)
(SBY
only)
No
IFS1 •
IMS1 + IFS2 •
IMS2 = 1?
(SBY
only)
No
Yes
Restart
processor clocks
Execute
next instruction
No
Reset MCU
IF = 1,
IM = 0, and
IE = 1?
Execute
next instruction
Yes
Accept interrupt
Figure 15 MCU Operation Flowchart
29
HD404639R Series
Stop mode
Oscillator
Internal
clock
RESET
STOPC
tres
STOP instruction execution
tres ≥ tRC (stabilization period)
Figure 16 Timing of Stop Mode Cancellation
Subactive Mode: The OSC1 and OSC2 oscillator stops and the MCU operates with a clock generated by
the X1 and X2 oscillator. In this mode, functions other than the DTMF generator operate. However,
because the operating clock is slow, the power dissipation becomes low, next to watch mode.
The CPU instruction execution speed can be selected as 244 µs or 122 µs by setting bit 2 (SSR12) of
system clock select register 1 (SSR1: $029). Note that the SSR12 value must be changed in active mode.
If the value is changed in subactive mode, the MCU may malfunction.
When the STOP or SBY instruction is executed in subactive mode, the MCU enters either watch or active
mode, depending on the statuses of the low speed on flag (LSON: $020, bit 0) and the direct transfer on
flag (DTON: $020, bit 3).
Subactive mode is an optional function that the user must specify on the function option list.
Interrupt Frame: In watch and subactive modes, φCLK is applied to timer A and the INT0 circuit.
Prescaler W and timer A operate as the time-base and generate the timing clock for the interrupt frame.
Three interrupt frame lengths (T) can be selected by setting the miscellaneous register (MIS: $00C) (figure
18).
In watch and subactive modes, the timer-A/INT0 interrupt is generated synchronously with the interrupt
frame. The interrupt request is generated synchronously with the interrupt strobe timing except during
transition to active mode. The falling edge of the INT0 signal is input asynchronously with the interrupt
frame timing, but it is regarded as input synchronously with the second interrupt strobe clock after the
falling edge. An overflow and interrupt request in timer A is generated synchronously with t he interrupt
strobe timing.
Note on Use: When the MCU is in watch mode or sub-active mode and if the high level period before the
falling edge of INT0 is shorter than the interrupt frame or if the low level period after the falling edge of
INT0 is shorter than the interrupt frame, INT0 is not detected. Therefore, the high or low level period of
INT 0 must be held longer than the interrupt frame when the MCU is in watch mode or subactive mode.
30
HD404639R Series
Oscillation
stabilization period
Active mode
Watch mode
Active mode
Interrupt strobe
INT0
Interrupt request
generation
T
(During the transition
from watch mode to
active mode only)
tRC
T
TX
T: Interrupt frame length
t RC : Oscillation stabilization period
Note : If the time from the fall of the INT0 signal until the interrupt is accepted and
active mode is entered is TX, then TX will be in the following range :
T + tRC ≤ TX ≤ 2T + tRC
Figure 17 Interrupt Frame
Miscellaneous register (MIS: $00C)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
MIS3
W
W
W
W
MIS3
MIS2
MIS1
MIS0
MIS2
Buffer control.
Refer to figure 38.
MIS1
MIS0
0
0
T *1
tRC* 1
Oscillation circuit conditions
0.24414 ms 0.12207 ms
External clock input
*2
0.24414 ms
0
1
15.625 ms
7.8125 ms
Ceramic oscillator
1
0
62.5 ms
31.25 ms
Crystal oscillator
1
1
Not used
—
Notes: 1. The values of T and tRC are applied when a 32.768-kHz crystal oscillator is used.
2. The value is applied only when direct transfer operation is used.
Figure 18 Miscellaneous Register (MIS)
31
HD404639R Series
Direct Transition from Subactive Mode to Active Mode: Available by controlling the direct transfer on
flag (DTON: $020, bit 3) and the low speed on flag (LSON: $020, bit 0). The procedures are described
below:
• Set LSON to 0 and DTON to 1 in subactive mode.
• Execute the STOP or SBY instruction.
• The MCU automatically enters active mode from subactive mode after waiting for the MCU internal
processing time and oscillation stabilization time (figure 19).
Notes: 1. The DTON flag ($020, bit 3) can be set only in subactive mode. It is always reset in active
mode.
2. The transition time (TD) from subactive mode to active mode:
tRC < TD < T + tRC
STOP/SBY instruction execution
MCU internal
Subactive mode
processing period
Oscillation
stabilization
time
Active mode
(Set LSON = 0, DTON = 1)
Interrupt strobe
Direct transfer
completion timing
t RC
T
TD
T:
tRC:
TD:
Interrupt frame length
Oscillation stabilization period
Transition time
Figure 19 Direct Transition Timing
Stop Mode Cancellation by STOPC: The MCU enters active mode from stop mode by a STOPC input as
well as by RESET. In either case, the MCU starts instruction execution from the starting address (address
0) of the program. However, the value of the RAM enable flag (RAME: $021, bit 3) differs between
cancellation by STOPC and by RESET. When stop mode is cancelled by RESET, RAME = 0; when
cancelled by STOPC, RAME = 1. RESET can cancel all modes, but STOPC is valid only in stop mode;
STOPC input is ignored in other modes. Therefore, when the program requires to confirm that stop mode
has been cancelled by STOPC (for example, when the RAM contents before entering stop mode are used
after transition to active mode), execute the TEST instruction on the RAM enable flag (RAME) at the
beginning of the program.
MCU Operation Sequence: The MCU operates in the sequences shown in figures 20 to 22. It is reset by
an asynchronous RESET input, regardless of its status.
The low-power mode operation sequence is shown in figure 22. With the IE flag cleared and an interrupt
flag set together with its interrupt mask cleared, if a STOP/SBY instruction is executed, the instruction is
32
HD404639R Series
cancelled (regarded as an NOP) and the following instruction is executed. Before executing a STOP/SBY
instruction, make sure all interrupt flags are cleared or all interrupts are masked.
Power on
RESET = 1 ?
No
Yes
RAME = 0
MCU
operation
cycle
Reset MCU
Figure 20 MCU Operating Sequence (Power On)
33
HD404639R Series
MCU operation
cycle
IF = 1?
No
Instruction
execution
Yes
SBY/STOP
instruction?
Yes
No
IM = 0 and
IE = 1?
Yes
IE ← 0
Stack ← (PC),
(CA),
(ST)
No
Low-power mode
operation cycle
IF:
IM:
IE:
PC:
CA:
ST:
PC ← Next
location
PC ← Vector
address
Interrupt request flag
Interrupt mask
Interrupt enable flag
Program counter
Carry flag
Status flag
Figure 21 MCU Operating Sequence (MCU Operation Cycle)
34
HD404639R Series
Low-power mode
operation cycle
IF = 1 and
IM = 0?
No
Yes
Standby/Watch
mode
No
IF = 1 and
IM = 0?
Yes
Stop mode
No
STOPC = 0?
Yes
Hardware NOP
execution
Hardware NOP
execution
RAME = 1
PC ← Next
Iocation
PC ← Next
Iocation
Reset MCU
Instruction
execution
MCU operation
cycle
For IF and IM operation, refer to figure 15.
Figure 22 MCU Operating Sequence (Low-Power Mode Operation)
35
HD404639R Series
Internal Oscillator Circuit
A block diagram of the clock generation circuit is shown in figure 23. As shown in table 20, a ceramic
oscillator or crystal oscillator can be connected to OSC1 and OSC2, and a 32.768-kHz oscillator can be
connected to X1 and X2. The system oscillator can also be operated by an external clock. System clock
select register 1 (SSR1: $029) and system clock select register 2 (SSR2: $02A) must be selected according
to the frequency of the oscillator connected to OSC1 and OSC2 (figure 24).
Note: If the SSR10, SSR11, SSR22 and SSR23 setting does not match the oscillator frequency, the
DTMF generator and subsystems using the 32.768-kHz oscillation will malfunction.
LSON
OSC2
System fOSC
oscillator
OSC1
fX
X1
Subsystem
oscillator
1/4 or
1/8 or
1/16 or
1/32
division
circuit* 1
fcyc
tcyc
Timing
generator
circuit
øCPU
CPU with ROM,
RAM, registers,
flags, and I/O
øPER
Peripheral
function
interrupt
System
clock
selection
fSUB
1/8 or 1/4
Timing
division tsubcyc generator
circuit*2
circuit
TMA3
X2
1/8
division
circuit
fW
tWcyc
Timing
generator
circuit
Time-base
clock øCLK
selection
Notes: 1. 1/4, 1/8, 1/16 or 1/32 division ratio can be selected by setting bits 1 and 0 of
system clock select register 2 (SSR2: $02A).
2. 1/8 or 1/4 division ratio can be selected by setting bit 2 of system clock select
register 1 (SSR1: $029).
Figure 23 Clock Generation Circuit
36
Time-base
interrupt
HD404639R Series
System clock select register 1 (SSR1: $029)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SSR13
SSR12
SSR11
SSR10
Bit name
SSR13
32-kHz oscillation stop
0
Oscillation operates in stop mode
1
Oscillation stops in stop mode
SSR23 SSR22
0
0
SSR10
0
0
400 kHz
1
800 kHz
0
2 MHz
1
4 MHz
1
SSR12
32-kHz oscillation division
ratio selection
0
fSUB = fX/8
1
fSUB = fX/4
1
1
0
1
System clock
selection
SSR11
Don’t care Don’t care 3.58 MHz
1
1
8 MHz
Don’t care Don’t care 7.16 MHz
Figure 24 System Clock Select Register 1 (SSR1)
GND
X2
X1
RESET
OSC2
OSC1
TEST
GND
Figure 25 Typical Layouts of Crystal and Ceramic Oscillator
37
HD404639R Series
The division ratio of the system clock can be selected as 1/4, 1/8, 1/16, or 1/32 by setting bits 0 and 1
(SSR20, SSR21) of system clock select register 2 (SSR2: $02A).
The values of SSR20 and SSR21 are valid after the MCU enters watch mode (SSR22 and SSR23 are valid
directly). The system clock must be stopped when the division ratio is to be changed.
There are two ways for setting the division ratio of the system clock.
• The division ratio is selected by setting SSR20 and SSR21 in active mode (at this time, the presetting
values of SSR20 and SSR21 are valid). This causes the MCU to enter watch mode (system clock is
stopped). When the MCU enters active mode from watch mode, the setting values of SSR20 and
SSR21 become valid.
• The division ratio can also be selected by setting SSR20 and SSR21 in subactive mode. This causes the
MCU to enter active mode via watch mode, thus validating the setting values of SSR20 and SSR21 (so
does the case of direct transition).
After RESET input or after stop mode has been cancelled, the division ratio of the system clock can be
selected as 1/4 or 1/32 by setting the SEL pin level.
• 1/4 division ratio: Connect SEL to VCC.
• 1/32 division ratio: Connect SEL to GND.
The division ratio of the subsystem clock can be selected as 1/4 or 1/8 by setting bit 2 (SSR12) of system
clock select register 1 (SSR1: $029).
SSR12 is valid directly after being set, but in order to change the value of SSR12, the MCU must be in
active mode. If SSR12 is changed in subactive mode, the MCU will malfunction.
38
HD404639R Series
System clock select register 2 (SSR2: $02A)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SSR23
SSR22
SSR21
SSR20
Bit name
SSR23
SSR22
0
0
Selected from 400 kHz,
800 kHz, 2 MHz, 4 MHz*2
1
3.58 MHz
0
8 MHz*2
1
7.16 MHz
1
System clock selection
*1
System clock division ratio
SSR21
SSR20
0
0
1/4 division
1
1/8 division
0
1/16 division
1
1/32 division
1
Notes: 1. The DTMF frequencies are not affected by the setting of the system clock division ratio.
2. Refer to system clock select register 1 (SSR1) of figure 24.
Figure 26 System Clock Select Register 2 (SSR2)
39
HD404639R Series
Table 20 Oscillator Circuit Examples
Circuit
Configuration
External clock
operation
Circuit Constants
External
oscillator
OSC 1
Open
OSC 2
Ceramic oscillator
(OSC1, OSC 2)
C1
OSC1
Ceramic
oscillator
Rf
Ceramic oscillator: CSB400P22 (Murata),
CSB400P (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 220 pF ± 5%
OSC2
C2
GND
Ceramic oscillator: CSB800J122 (Murata),
CSB800J (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 220 pF ± 5%
Ceramic oscillator: CSA2.00MG (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Ceramic oscillator: CSA4.00MG (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Ceramic oscillator: CSA3.58MG (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
Ceramic oscillator: CSA8.00MT (Murata)
Rf = 1 MΩ ± 20%
C1 = C2 = 30 pF ± 20%
40
HD404639R Series
Circuit
Configuration
Circuit Constants
Rf = 1 MΩ ± 20%
C1 = C2 = 10–22 pF ± 20%
Crystal: Equivalent to circuit shown below
C0 = 7 pF max
RS = 100 Ω max
f = 400 kHz, 800 kHz, 2 MHz, 3.58 MHz, 4
MHz, 7.16 MHz, 8 MHz
C1
Crystal oscillator
(OSC1, OSC 2)
OSC1
Crystal
oscillator
Rf
OSC2
C2
GND
L
CS RS
OSC1
OSC2
C0
C1
Crystal oscillator
(X1, X2)
Crystal: 32.768 kHz: MX38T (Nippon
Denpa)
C1 = C2 = 20 pF ± 20%
RS: 14 kΩ
C0: 1.5 pF
X1
Crystal
oscillator
X2
C2
GND
L
CS RS
X1
X2
C0
Notes: 1. Since the circuit constants change depending on the crystal or ceramic oscillator and stray
capacitance of the board, the user should consult with the crystal or ceramic oscillator
manufacturer to determine the circuit parameters.
2. Wiring among OSC1, OSC 2, X1, X2, and elements should be as short as possible, and must not
cross other wiring (see figure 25).
3. If the 32.768-kHz crystal oscillator is not used, the X1 pin must be fixed to VCC and X2 must be
open.
41
HD404639R Series
Input/Output
The MCU has 61 input/output pins (D0–D11, R0 0–RC 0) and 7 input pins (D12, D13, RD0–RD3, RE 0). The
features are described below.
• A maximum current of 15 mA is allowed for each of the pins D 4 to D11 with a total maximum current of
less than 105 mA. In addition, D0–D3 can each act as a 10-mA maximum current source.
• Some input/output pins are multiplexed with peripheral function pins such as those for the timers or
serial interface. For these pins, the peripheral function setting is done prior to the D or R port setting.
Therefore, when a peripheral function is selected for a pin, the pin function and input/output selection
are automatically switched according to the setting.
• Input or output selection for input/output pins and port or peripheral function selection for multiplexed
pins are set by software.
• Peripheral function output pins are CMOS output pins. Only the R43/SO1 and R5 3/SO 2 pins can be set to
NMOS open-drain output by software.
• In stop mode, the MCU is reset, and therefore peripheral function selection is cancelled. Input/output
pins are in high-impedance state.
• Pins D0–D3 have built-in pull-down MOS, and other input/output pins have built-in pull-up MOS, which
can be individually turned on or off by software.
I/O buffer configuration is shown in figure 27, programmable I/O circuits are listed in table 21, and I/O pin
circuit types are shown in table 22.
Table 21-1 Programmable I/O Circuits (with Pull-Up MOS)
MIS3 (Bit 3 of MIS)
0
DCD, DCR
0
PDR
0
1
0
1
0
1
0
1
PMOS
—
—
—
On
—
—
—
On
NMOS
—
—
On
—
—
—
On
—
—
—
—
—
—
On
—
On
CMOS buffer
Pull-up MOS
Note: — indicates off status.
42
1
1
0
1
HD404639R Series
D4–D11, R port
HLT
Pull-up control signal
VCC
MIS3
VCC
Pull-up
MOS
Buffer control signal
DCD, DCR
Output data
PDR
Input data
Input control signal
Figure 27-1 I/O Buffer Configuration (with Pull-Up MOS)
Table 21-2 Programmable I/O Circuits (with Pull-Down MOS)
MIS3 (Bit 3 of MIS)
0
DCD, DCR
0
PDR
0
1
0
1
0
1
0
1
PMOS
—
—
—
On
—
—
—
On
NMOS
—
—
On
—
—
—
On
—
—
—
—
—
On
—
On
—
CMOS buffer
Pull-down MOS
1
1
0
1
Note: — indicates off status.
43
HD404639R Series
D0–D3 port
Input control signal
Input data
VCC
Buffer control signal
DCD
Output data
Pull-Down
Mos
PDR
MIS3
Pull-down control signal
HLT
Figure 27-2 I/O Buffer Configuration (with Pull-Down MOS)
44
HD404639R Series
Table 22 Circuit Configurations of I/O Pins
I/O Pin Type
Input/output
pins
Circuit
VCC
Pins
HLT
Pull-up control signal
Buffer control
signal
VCC
MIS3
DCD, DCR
Output data
PDR
D4–D 11 , R0 0–R0 3
R1 0–R1 3, R2 0–R2 3
R3 0–R3 3, R4 0–R4 2
R5 0–R5 2 R6 0–R6 3
R7 0–R7 3, R8 0–R8 3
R9 0–R9 3, RA 0–RA 3
RB 0–RB 3, RC0
Input data
Input control signal
Input control signal
D0–D 3
Input data
VCC
Buffer control signal
DCD
Output data
PDR
MIS3
Pull-down control
signal
HLT
VCC
HLT
VCC
Pull-up control signal
Buffer control
signal
Output data
R4 3, R5 3
MIS3
DCR
MIS2, SM2B2
PDR
Input data
Input control signal
Input pins
Input data
D12, D13
RD0–RD3, RE 0
Input control signal
45
HD404639R Series
I/O Pin Type
Circuit
Peripheral
Input/
function pins output
pins
VCC
Pins
HLT
VCC
Pull-up control signal
Output data
Input data
Peripheral
Output
function pins pins
VCC
Pull-up control signal
Output data
VCC
MIS2, SM2B2
SO1, SO2
Input data
TOB, TOC, TOD
MIS3
TOB, TOC, TOD
VCC
Input data
SO1, SO2
MIS3
HLT
Pull-up control signal
Output data
Input
pins
SCK1, SCK2
SCK1, SCK2
PMOS control
signal
VCC
MIS3
HLT
VCC
SCK 1, SCK 2
HLT
MIS3
PDR
SI1, SI2, INT1, etc
INT0, STOPC
SI 1, SI 2, INT1, INT2,
INT3, INT4, EVNB,
EVND
INT0, STOPC
Notes: 1. The MCU is reset in stop mode, and peripheral function selection is cancelled. The HLT signal
becomes low, and input/output pins enter high-impedance state.
2. The HLT signal is 1 in watch and subactive modes.
D Port (D0–D13): Consist of 12 input/output pins and 2 input pins addressed by one bit. D0–D3 are highcurrent sources, D4–D11 are high-current sinks, and D12 and D 13 are input-only pins.
Pins D0–D 11 are set by the SED and SEDD instructions, and reset by the RED and REDD instructions.
Output data is stored in the port data register (PDR) for each pin. All pins D0–D13 are tested by the TD and
TDD instructions.
The on/off statuses of the output buffers are controlled by D-port data control registers (DCD0–DCD2:
$02C–$02E) that are mapped to memory addresses (figure 28).
46
HD404639R Series
Pins D 12 and D13 are multiplexed with peripheral function pins STOPC and INT0, respectively. The
peripheral function modes of these pins are selected by bits 2 and 3 (PMRC2, PMRC3) of port mode
register C (PMRC: $025) (figure 29).
R Ports (R0 0–RC0, RD0–RE0): 49 input/output pins and 5 input pins addressed in 4-bit units. Data is input
to these ports by the LAR and LBR instructions, and output from them by the LRA and LRB instructions.
Output data is stored in the port data register (PDR) for each pin. The on/off statuses of the output buffers
of the R ports are controlled by R-port data control registers (DCR0–DCRC: $030–$03C) that are mapped
to memory addresses (figure 28).
Pins R00–R03 are multiplexed with peripheral pins INT1–INT 4, respectively. The peripheral function modes
of these pins are selected by bits 0–3 (PMRB0–PMRB3) of port mode register B (PMRB: $024) (figure
30).
Pins R30–R32 are multiplexed with peripheral pins TOB, TOC, and TOD, respectively. The peripheral
function modes of these pins are selected by bits 0 and 1 (TMB20, TMB21) of timer mode register B2
(TMB2: $013), bits 0–2 (TMC20–TMC22) of timer mode register C2 (TMC2: $014), and bits 0–3
(TMD20–TMD23) of timer mode register D2 (TMD2: $015) (figures 31, 32, and 33).
Pins R33 and R40 are multiplexed with peripheral pins EVNB and EVND, respectively. The peripheral
function modes of these pins are selected by bits 0 and 1 (PMRC0, PMRC1) of port mode register C
(PMRC: $025) (figure 29).
Pins R41–R43 are multiplexed with peripheral pins SCK 1, SI1, and SO1, respectively. The peripheral
function modes of these pins are selected by bit 3 (SM1A3) of serial mode register 1A (SM1A: $005), and
bits 0 and 1 (PMRA0, PMRA1) of port mode register A (PMRA: $004), as shown in figures 34 and 36.
Ports R51–R5 3 are multiplexed with peripheral function pins SCK 2, SI2, SO2, respectively. The function
modes of these pins can be selected by individual pins, by setting bit 3 (SM2A3) of serial mode register 2A
(SM2A: $01B), and bits 2 and 3 (PMRA2, PMRA3) of port mode register A (PMRA: $004) (figures 35 and
36).
Ports RD 0–RD3 are multiplexed with peripheral function pins COMP0–COMP3, respectively. The function
modes of these pins are selected by bit 3 (CER3) of the compare enable register (CER: $018).
Port RE 0 is multiplexed with peripheral function pin VCref. While functioning as VC ref , do not use this pin
as an R port at the same time, otherwise, the MCU may malfunction.
Pull-Up or Pull-Down MOS Transistor Control: A program-controlled pull-up or pull-down MOS
transistor is provided for each input/output pin other than input-only pins D 12 and D 13. The on/off status of
all these transistors is controlled by bit 3 (MIS3) of the miscellaneous register (MIS: $00C), and the on/off
status of an individual transistor can also be controlled by the port data register (PDR) of the corresponding
pin—enabling on/off control of that pin alone (table 21 and figure 38).
The on/off status of each transistor and the peripheral function mode of each pin can be set independently.
How to Deal with Unused I/O Pins: I/O pins that are not needed by the user system (floating) must be
connected to V CC to prevent LSI malfunctions due to noise. These pins must either be pulled up to VCC by
their pull-up MOS transistors or by resistors of about 100 kΩ or pulled down to GND by their pull-down
MOS transistors.
47
HD404639R Series
Data control register
DCD0 to DCD2
Bit
(DCD0 to 2: $02C to $02E)
(DCR0 to C: $030 to $03C)
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
DCD03– DCD02– DCD01– DCD00–
DCD23 DCD22 DCD21 DCD20
DCR0 to DCRB
Bit
2
3
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
DCR03– DCR02– DCR01– DCR00–
DCRB3 DCRB2 DCRB1 DCRB0
DCRC
Bit
3
2
1
0
Initial value
—
—
—
0
Read/Write
—
—
—
W
Bit name
Not used Not used Not used DCRC0
All Bits
CMOS Buffer On/Off Selection
0
Off (high-impedance)
1
On
Correspondence between ports and DCD/DCR bits
Register Name
DCD0
DCD1
DCD2
DCR0
DCR1
DCR2
DCR3
DCR4
DCR5
DCR6
DCR7
DCR8
DCR9
DCRA
DCRB
DCRC
Bit 3
D3
D7
D11
R03
R13
R23
R33
R43
R53
R63
R73
R83
R93
RA3
RB3
—
Bit 2
D2
D6
D10
R02
R12
R22
R32
R42
R52
R62
R72
R82
R92
RA2
RB2
—
Bit 1
D1
D5
D9
R01
R11
R21
R31
R41
R51
R61
R71
R81
R91
RA1
RB1
—
Figure 28 Data Control Registers (DCD, DCR)
48
Bit 0
D0
D4
D8
R00
R10
R20
R30
R40
R50
R60
R70
R80
R90
RA0
RB0
RC0
HD404639R Series
Port mode register C (PMRC: $025)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
PMRC1
PMRC0
Bit name
PMRC3 PMRC2 *
PMRC0
R33/EVNB mode selection
0
R33
1
EVNB
PMRC1
R40/EVND mode selection
0
R40
1
EVND
PMRC2
D12/STOPC mode selection
0
D12
1
STOPC
PMRC3
D13/INT0 mode selection
0
D13
1
INT0
Note: PMRC2 is reset to 0 only by RESET input. When STOPC is input in stop
mode, PMRC2 is not reset but retains its value.
Figure 29 Port Mode Register C (PMRC )
49
HD404639R Series
Port mode register B (PMRB: $024)
Bit
3
2
1
0
Initial value
0
0
0
0
W
W
W
Read/Write
Bit name
W
PMRB3
PMRB2 PMRB1 PMRB0
PMRB0
R00/INT1 mode selection
0
R00
1
INT1
PMRB1
R01/INT2 mode selection
0
R01
1
INT2
PMRB2
R02/INT3 mode selection
0
R02
1
INT3
PMRB3
R03/INT4 mode selection
0
R03
1
INT4
Figure 30 Port Mode Register B (PMRB)
Timer mode register B2 (TMB2: $013)
Bit
3
2
1
0
Initial value
—
—
0
0
Read/Write
—
—
R/W
R/W
Bit name
Not used Not used TMB21
TMB20
R30/TOB mode selection
TMB21
TMB20
0
0
R30
R30 port
1
TOB
Toggle output
0
TOB
0 output
1
TOB
1 output
1
Figure 31 Timer Mode Register B2 (TMB2)
50
HD404639R Series
Timer mode register C2 (TMC2: $014)
Bit
3
Initial value
—
0
0
0
Read/Write
—
R/W
R/W
R/W
TMC21
TMC20
Bit name
2
0
1
Not used TMC22
TMC22
TMC21
TMC20
0
0
0
R31
R31 port
1
TOC
Toggle output
0
TOC
0 output
1
TOC
1 output
0
TOC
Inhibited
1
TOC
0
TOC
1
TOC
1
1
0
1
R31/TOC mode selection
PWM output
Figure 32 Timer Mode Register C2 (TMC2)
51
HD404639R Series
Timer mode register D2 (TMD2: $015)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
TMD23
TMD22
TMD21
TMD20
Bit name
R32/TOD mode selection
TMD23
TMD22
TMD21
TMD20
0
0
0
0
R32
R32 port
1
TOD
Toggle output
0
TOD
0 output
1
TOD
1 output
0
TOD
Inhibited
1
TOD
0
TOD
1
TOD
PWM output
R32
Input capture (R32 port)
1
1
0
1
1
Don’t care Don’t care Don’t care
Figure 33 Timer Mode Register D2 (TMD2)
52
HD404639R Series
Serial mode register 1A (SM1A: $005)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM1A3
SM1A2
SM1A1
SM1A0
Bit name
SM1A3
R41/SCK1
mode selection
0
R41
1
SCK1
Prescaler
division
ratio
SM1A2
SM1A1
SM1A0
SCK1
Clock source
0
0
0
Output
Prescaler
÷2048
1
Output
Prescaler
÷512
0
Output
Prescaler
÷128
1
Output
Prescaler
÷32
0
Output
Prescaler
÷8
1
Output
Prescaler
÷2
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
Figure 34 Serial Mode Register 1A (SM1A)
53
HD404639R Series
Serial mode register 2A (SM2A: $01B)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM2A3
SM2A2
SM2A1
SM2A0
Bit name
SM2A3
R51/SCK 2
mode selection
0
R51
1
SCK2
SM2A2
SM2A1
SM2A0
SCK2
Clock source
Prescaler
division
ratio
0
0
0
Output
Prescaler
÷2048
1
Output
Prescaler
÷512
0
Output
Prescaler
÷128
1
Output
Prescaler
÷32
0
Output
Prescaler
÷8
1
Output
Prescaler
÷2
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
Figure 35 Serial Mode Register 2A (SM2A)
54
HD404639R Series
Port mode register A (PMRA: $004)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
PMRA3
PMRA2 PMRA1 PMRA0
PMRA0
R43/SO1 mode selection
0
R43
1
SO1
PMRA1
R42/SI1 mode selection
0
R42
1
SI1
PMRA2
R53/SO2 mode selection
0
R53
1
SO2
PMRA3
R52/SI2 mode selection
0
R52
1
SI2
Figure 36 Port Mode Register A (PMRA)
55
HD404639R Series
Compare enable register (CER: $018)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
CER3
CER2
CER1
CER0
Bit name
CER3
Digital/Analog selection
CER1
CER0
Analog input pin selection
Digital input mode:
RD0 /COMP0 –RD3 /COMP3
operate as an R port.
0
0
COMP0
0
0
1
COMP1
1
0
COMP2
1
Analog input mode:
RD0 /COMP0 –RD 3 /COMP3
operate as analog input.
1
1
COMP3
CER2
Reference voltage selection
0
External input voltage
1
Internal voltage
Figure 37 Compare Enable Register (CER)
Miscellaneous register (MIS: $00C)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
MIS3
MIS2
MIS1
MIS0
MIS2
PMOS transistor
on/off selection
for pin R43/SO1
Bit name
MIS3
Pull-up and
pull-down MOS
on/off selection
0
Off
0
On
1
On
1
Off
MIS1
tRC selection.
Refer to figure 18 in the
operation modes section.
Figure 38 Miscellaneous Register (MIS)
56
MIS0
HD404639R Series
Prescalers
The MCU has the following two prescalers, S and W.
The prescalers operating conditions are listed in table 23, and the prescalers output supply is shown in
figure 39. The timers A–D input clocks except external events and the serial transmit clock except the
external clock are selected from the prescaler outputs, depending on corresponding mode registers.
Prescaler Operation
Prescaler S: 11-bit counter that inputs a system clock signal. After being reset to $000 by MCU reset,
prescaler S divides the system clock. Prescaler S keeps counting, except in watch and stop modes and at
MCU reset.
Prescaler W: Five-bit counter that inputs the X1 input clock signal (32-kHz crystal oscillation) divided by
eight. After being reset to $00 by MCU reset, prescaler W divides the input clock. Prescaler W can be
reset by software.
Table 23 Prescaler Operating Conditions
Prescaler
Input Clock
Reset Conditions
Stop Conditions
Prescaler S
System clock (in active and standby mode),
Subsystem clock (in subactive mode)
MCU reset
MCU reset,
stop mode,
watch mode
Prescaler W
32-kHz crystal oscillation
MCU reset, software
MCU reset,
stop mode
Subsystem
clock
fX/8
Prescaler W
fX/4 or fX/8
Timer A
Timer B
Timer C
System
clock
Clock
selector
Prescaler S
Timer D
Serial
interface 1
Serial
interface 2
Figure 39 Prescaler Output Supply
57
HD404639R Series
Timers
The MCU has four timer/counters (A to D).
•
•
•
•
Timer A:
Timer B:
Timer C:
Timer D:
Free-running timer
Multifunction timer
Multifunction timer
Multifunction timer
Timer A is an 8-bit free-running timer. Timers B–D are 8-bit multifunction timers, whose functions are
listed in table 24. The operating modes are selected by software.
Table 24 Timer Functions
Functions
Clock source
Timer functions
Timer outputs
Timer A
Timer B
Timer C
Timer D
Prescaler S
Available
Available
Available
Available
Prescaler W
Available
—
—
—
External event
—
Available
—
Available
Free-running
Available
Available
Available
Available
Time-base
Available
—
—
—
Event counter
—
Available
—
Available
Reload
—
Available
Available
Available
Watchdog
—
—
Available
—
Input capture
—
—
—
Available
Toggle
—
Available
Available
Available
0 output
—
Available
Available
Available
1 output
—
Available
Available
Available
PWM
—
—
Available
Available
Note: — means not available.
Timer A
Timer A Functions: Timer A has the following functions.
• Free-running timer
• Clock time-base
The block diagram of timer A is shown in figure 40.
58
HD404639R Series
1/4
1/2
2 fW
fW
t Wcyc
Timer A interrupt
request flag
(IFTA)
Prescaler W
(PSW)
÷2
÷8
÷ 16
÷ 32
32.768-kHz
oscillator
1/2 t Wcyc
Clock
Timer
counter A
(TCA) Overflow
System
clock
ø PER
÷2
÷4
÷8
÷ 32
÷ 128
÷ 512
÷ 1024
÷ 2048
Selector
Internal data bus
Selector
Selector
Prescaler S (PSS)
3
Timer mode
register A
(TMA)
Figure 40 Block Diagram of Timer A
Timer A Operations:
• Free-running timer operation: The input clock for timer A is selected by timer mode register A (TMA:
$008).
Timer A is reset to $00 by MCU reset and incremented at each input clock. If an input clock is applied
to timer A after it has reached $FF, an overflow is generated, and timer A is reset to $00. The overflow
sets the timer A interrupt request flag (IFTA: $001, bit 2). Timer A continues to be incremented after
reset to $00, and therefore it generates regular interrupts every 256 clocks.
• Clock time-base operation: Timer A is used as a clock time-base by setting bit 3 (TMA3) of timer
mode register A (TMA: $008) to 1. The prescaler W output is applied to timer A, and timer A
generates interrupts at the correct timing based on the 32.768-kHz crystal oscillation. In this case,
prescaler W and timer A can be reset to $00 by software.
Registers for Timer A Operation: Timer A operating modes are set by the following registers.
• Timer mode register A (TMA: $008): Four-bit write-only register that selects timer A’s operating mode
and input clock source as shown in figure 41.
59
HD404639R Series
Timer mode register A (TMA: $008)
Bit
3
2
1
0
Initial value
0
0
0
0
W
W
W
W
TMA3
TMA2
TMA1
TMA0
Read/Write
Bit name
Source
Input clock
TMA3 TMA2 TMA1 TMA0 prescaler frequency Operating mode
0
0
0
1
1
0
1
1
0
0
1
1
0
1
0
PSS
2048tcyc
1
PSS
1024tcyc
0
PSS
512tcyc
1
PSS
128tcyc
0
PSS
32tcyc
1
PSS
8tcyc
0
PSS
4tcyc
1
PSS
2tcyc
0
PSW
32tWcyc
1
PSW
16tWcyc
0
PSW
8tWcyc
1
PSW
2tWcyc
0
PSW
1/2tWcyc
1
Inhibited
Don’t
care
Timer A mode
Time-base
mode
PSW and TCA reset
Notes: 1. tWcyc = 244.14 µs (when a 32.768-kHz crystal oscillator is used)
2. Timer counter overflow output period (seconds) = input clock period (seconds) × 256.
3. The division ratio must not be modified during time-base mode operation, otherwise
an overflow cycle error will occur.
Figure 41 Timer Mode Register A (TMA)
60
HD404639R Series
Timer B
Timer B Functions: Timer B has the following functions.
• Free-running/reload timer
• External event counter
• Timer output operation (toggle, 0, and 1 outputs)
The block diagram of timer B is shown in figure 42.
Timer B interrupt
request flag
(IFTB)
Timer output
control logic
TOB
Timer read register BU (TRBU)
Timer output control
Timer read
register BL
(TRBL)
Clock
System
clock
ø PER
÷ 2048
EVNB
÷2
÷4
÷8
÷ 32
÷ 128
÷ 512
Selector
Timer write
register BU
(TWBU)
Prescaler S (PSS)
Free-running/
Reload control
Timer write
register BL
(TWBL)
Internal data bus
Timer counter B
(TCB)
Overflow
3
Timer mode
register B1
(TMB1)
2
Timer mode
register B2
(TMB2)
Figure 42 Block Diagram of Timer B
61
HD404639R Series
Timer B Operations:
• Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register B1 (TMB1: $009).
Timer B is initialized to the value set in timer write register B (TWBL: $00A, TWBU: $00B) by
software and incremented by one at each clock input. If an input clock is applied to timer B after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer B is
initialized to its initial value set in timer write register B; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
The overflow sets the timer B interrupt request flag (IFTB: $002, bit 0). IFTB is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
• External event counter operation: Timer B is used as an external event counter by selecting external
event input as the input clock source. In this case, pin R33/EVNB must be set to EVNB by port mode
register C (PMRC: $025).
Timer B is incremented by one at each falling edge of signals input to pin EVNB. The other operations
are basically the same as the free-running/reload timer operation.
• Timer output operation: The following three output modes can be selected for timer B by setting timer
mode register B2 (TMB2: $013).
Toggle
0 output
1 output
By selecting the timer output mode, pin R30/TOB is set to TOB. The output from TOB is reset low by
MCU reset.
 Toggle output: When toggle output mode is selected, the output level is inverted if a clock is input
after timer B has reached $FF. By using this function and reload timer function, clock signals can
be output at a required frequency for the buzzer. The output waveform is shown in figure 43.
 0 output: When 0 output mode is selected, the output level is pulled low if a clock is input after
timer B has reached $FF. Note that this function must be used only when the output level is high.
 1 output: When 1 output mode is selected, the output level is set high if a clock is input after timer
B has reached $FF. Note that this function must be used only when the output level is low.
62
HD404639R Series
Toggle output waveform (timers B, C, and D)
Free-running timer
256 clock cycles
256 clock cycles
Reload timer
(256 – N) clock cycles (256 – N) clock cycles
PWM output waveform (timers C and D)
T × (N + 1)
TMC13 = 0
TMD13 = 0
T
T × 256
TMC13 = 1
TMD13 = 1
T × (256 – N)
Note: The waveform is always fixed low when N = $FF.
T: Input clock period to counter (figures 52 and 59)
N: The value of the timer write register
Figure 43 Timer Output Waveform
Registers for Timer B Operation: By using the following registers, timer B operation modes are selected
and the timer B count is read and written.
Timer mode register B1 (TMB1: $009)
Timer mode register B2 (TMB2: $013)
Timer write register B (TWBL: $00A, TWBU: $00B)
Timer read register B (TRBL: $00A, TRBU: $00B)
Port mode register C (PMRC: $025)
• Timer mode register B1 (TMB1: $009): Four-bit write-only register that selects the freerunning/reload timer function, input clock source, and the prescaler division ratio as shown in figure 44.
It is reset to $0 by MCU reset.
63
HD404639R Series
Writing to this register is valid from the second instruction execution cycle after the execution of the
previous timer mode register B1 write instruction. Setting timer B’s initialization by writing to timer
write register B (TWBL: $00A, TWBU: $00B) must be done after a mode change becomes valid.
Timer mode register B1 (TMB1: $009)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
TMB13
TMB12
TMB11
TMB10
Bit name
TMB13
Free-running/reload
timer selection
TMB12
TMB11
TMB10
0
Free-running timer
0
0
0
2048tcyc
1
Reload timer
1
512tcyc
0
128tcyc
1
32tcyc
0
8tcyc
1
4tcyc
0
2tcyc
1
R33/EVNB (external event input)
1
1
0
1
Input clock period and input
clock source
Figure 44 Timer Mode Register B1 (TMB1)
• Timer mode register B2 (TMB2: $013): Two-bit read/write register that selects the timer B output
mode as shown in figure 45. It is reset to $0 by MCU reset.
Timer mode register B2 (TMB2: $013)
Bit
3
2
1
0
Initial value
—
—
0
0
Read/Write
—
—
R/W
R/W
Bit name
Not used Not used TMB21
TMB20
TMB21
TMB20
0
0
R30
R30 port
1
TOB
Toggle output
0
TOB
0 output
1
TOB
1 output
1
R30/TOB mode selection
Figure 45 Timer Mode Register B2 (TMB2)
64
HD404639R Series
• Timer write register B (TWBL: $00A, TWBU: $00B): Write-only register consisting of the lower digit
(TWBL) and the upper digit (TWBU) as shown in figures 46 and 47. The lower digit is reset to $0 by
MCU reset, but the upper digit value is invalid.
Timer B is initialized by writing to timer write register B. In this case, the lower digit (TWBL) must be
written to first, but writing only to the lower digit does not change the timer B value. Timer B is
initialized to the value in timer write register B at the same time the upper digit (TWBU) is written to.
When timer write register B is written to again and if the lower digit value needs no change, writing
only to the upper digit initializes timer B.
Timer write register B (lower digit) (TWBL: $00A)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
TWBL3
TWBL2
TWBL1
TWBL0
Bit name
Figure 46 Timer Write Register B Lower Digit (TWBL)
Timer write register B (upper digit) (TWBU: $00B)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
W
W
W
W
TWBU3
TWBU2
TWBU1
TWBU0
Figure 47 Timer Write Register B Upper Digit (TWBU)
• Timer read register B (TRBL: $00A, TRBU: $00B): Read-only register consisting of the lower digit
(TRBL) and the upper digit (TRBU) that holds the count of the timer B upper digit (figures 48 and 49).
The upper digit (TRBU) must be read first. At this time, the count of the timer B upper digit is
obtained, and the count of the timer B lower digit is latched to the lower digit (TRBL). After this, by
reading TRBL, the count of timer B when TRBU is read can be obtained.
Timer read register B (lower digit) (TRBL: $00A)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRBL3
TRBL2
TRBL1
TRBL0
Figure 48 Timer Read Register B Lower Digit (TRBL)
65
HD404639R Series
Timer read register B (upper digit) (TRBU: $00B)
Bit
3
Initial value
Read/Write
Bit name
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRBU3
TRBU2
TRBU1
TRBU0
Figure 49 Timer Read Register B Upper Digit (TRBU)
• Port mode register C (PMRC: $025): Write-only register that selects R33/EVNB pin function as shown
in figure 50. It is reset to $0 by MCU reset.
Port mode register C (PMRC: $025)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
Bit name
PMRC3
PMRC2 PMRC1 PMRC0
PMRC0
R33/EVNB mode selection
0
R33
1
EVNB
PMRC1
R40/EVND mode selection
0
R40
1
EVND
PMRC2
D12/STOPC mode selection
0
D12
1
STOPC
PMRC3
D13/INT0 mode selection
0
D13
1
INT0
Figure 50 Port Mode Register C (PMRC)
66
HD404639R Series
Timer C
Timer C Functions: Timer C has the following functions.
• Free-running/reload timer
• Watchdog timer
• Timer output operation (toggle, 0, 1, and PWM outputs)
The block diagram of timer C is shown in figure 51.
System
reset signal
Watchdog on
flag (WDON)
TOC
Timer C interrupt
request flag
(IFTC)
Watchdog timer
control logic
Timer output
control logic
Timer read register CU (TRCU)
Timer output
control
Timer read
register CL
(TRCL)
Timer counter C
(TCC)
Timer write
register CU
(TWCU)
÷2
÷4
÷8
÷32
÷128
÷512
÷1024
÷2048
Selector
System øPER
clock
Prescaler S (PSS)
Overflow
Free-running
/Reload control
Timer write
register CL
(TWCL)
Internal data bus
Clock
3
Timer mode
register C1
(TMC1)
3
Timer mode
register C2
(TMC2)
Figure 51 Block Diagram of Timer C
67
HD404639R Series
Timer C Operations:
• Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register C1 (TMC1: $00D).
Timer C is initialized to the value set in timer write register C (TWCL: $00E, TWCU: $00F) by
software and incremented by one at each clock input. If an input clock is applied to timer C after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer C is
initialized to its initial value set in timer write register C; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
The overflow sets the timer C interrupt request flag (IFTC: $002, bit 2). IFTC is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
• Watchdog timer operation: Timer C is used as a watchdog timer for detecting out-of-control program
routines by setting the watchdog on flag (WDON: $020, bit 1) to 1. If a program routine runs out of
control and an overflow is generated, the MCU is reset. Program run can be controlled by initializing
timer C by software before it reaches $FF.
• Timer output operation: The following four output modes can be selected for timer C by setting timer
mode register C2 (TMC2: $014).
Toggle
0 output
1 output
PWM output
By selecting the timer output mode, pin R31/TOC is set to TOC. The output from TOC is reset low by
MCU reset.
 Toggle output: The operation is basically the same as that of timer-B’s toggle output.
 0 output: The operation is basically the same as that of timer-B’s 0 output.
 1 output: The operation is basically the same as that of timer-B’s 1 output.
 PWM output: When PWM output mode is selected, timer C provides the variable-duty pulse output
function. The output waveform differs depending on the contents of timer mode register C1
(TMC1: $00D) and timer write register C (TWCL: $00E, TWCU: $00F). The output waveform is
shown in figure 43.
Registers for Timer C Operation: By using the following registers, timer C operation modes are selected
and the timer C count is read and written.
Timer mode register C1 (TMC1: $00D)
Timer mode register C2 (TMC2: $014)
Timer write register C (TWCL: $00E, TWCU: $00F)
Timer read register C (TRCL: $00E, TRCU: $00F)
68
HD404639R Series
• Timer mode register C1 (TMC1: $00D): Four-bit write-only register that selects the freerunning/reload timer function, input clock source, and the prescaler division ratio as shown in figure 52.
It is reset to $0 by MCU reset.
Writing to this register is valid from the second instruction execution cycle after the execution of the
previous timer mode register C1 write instruction. Setting timer C’s initialization by writing to timer
write register C (TWCL: $00E, TWCU: $00F) must be done after a mode change becomes valid.
Timer mode register C1 (TMC1: $00D)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
TMC13
W
W
W
W
TMC13
TMC12
TMC11
TMC10
Free-running/reload timer selection
0
Free-running timer
1
Reload timer
Input clock period
TMC12
TMC11
TMC10
0
0
0
2048tcyc
1
1024tcyc
0
512tcyc
1
128tcyc
0
32tcyc
1
8tcyc
0
4tcyc
1
2tcyc
1
1
0
1
Figure 52 Timer Mode Register C1 (TMC1)
• Timer mode register C2 (TMC2: $014): Three-bit read/write register that selects the timer C output
mode as shown in figure 53. It is reset to $0 by MCU reset.
69
HD404639R Series
Timer mode register C2 (TMC2: $014)
Bit
3
2
1
0
Initial value
—
0
0
0
Read/Write
—
R/W
R/W
R/W
Not used TMC22
TMC21
TMC20
TMC22
TMC21
TMC20
0
0
0
R31
R31 port
1
TOC
Toggle output
0
TOC
0 output
1
TOC
1 output
0
TOC
Inhibited
1
TOC
0
TOC
1
TOC
Bit name
1
1
0
1
R31/TOC mode selection
PWM output
Figure 53 Timer Mode Register C2 (TMC2)
• Timer write register C (TWCL: $00E, TWCU: $00F): Write-only register consisting of a lower digit
(TWCL) and an upper digit (TWCU) as shown in figures 54 and 55. The operation of timer write
register C is basically the same as that of timer write register B (TWBL: $00A, TWBU: $00B).
Timer write register C (lower digit) (TWCL: $00E)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
W
W
W
W
TWCL3
TWCL2
TWCL1
TWCL0
Figure 54 Timer Write Register C Lower Digit (TWCL)
Timer write register C (upper digit) (TWCU: $00F)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
W
W
W
W
TWCU3
TWCU2
TWCU1
TWCU0
Figure 55 Timer Write Register C Upper Digit (TWCU)
70
HD404639R Series
• Timer read register C (TRCL: $00E, TRCU: $00F): Read-only register consisting of a lower digit
(TRCL) and an upper digit (TRCU) that holds the count of the timer C upper digit as shown in figures
56 and 57. The operation of timer read register C is basically the same as that of timer read register B
(TRBL: $00A, TRBU: $00B).
Timer read register C (lower digit) (TRCL: $00E)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRCL3
TRCL2
TRCL1
TRCL0
Figure 56 Timer Read Register C Lower Digit (TRCL)
Timer read register C (upper digit) (TRCU: $00F)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRCU3
TRCU2
TRCU1
TRCU0
Figure 57 Timer Read Register C Upper Digit (TRCU)
Timer D
Timer D Functions: Timer D has the following functions.
•
•
•
•
Free-running/reload timer
External event counter
Timer output operation (toggle, 0, 1, and PWM outputs)
Input capture timer
The block diagram for each operation mode of timer D is shown in figures 58 (A) and (B).
71
HD404639R Series
Timer D interrupt
request flag (IFTD)
Timer output
control logic
TOD
Timer read
register DU (TRDU)
Timer output
control
Timer read
register DL
(TRDL)
Clock
Timer write
register DU
(TWDU)
System
clock
øPER
÷2048
÷512
÷32
÷8
÷4
÷2
Edge
detection
logic
÷128
Selector
EVND
Overflow
Free-running/
Reload control
Timer write
register DL
(TWDL)
3
Prescaler S (PSS)
Timer mode
register D1
(TMD1)
3
Timer mode
register D2
(TMD2)
Edge detection control
2
Edge detection
selection register
2 (ESR2)
Figure 58 (A) Block Diagram of Timer D (Free-Running/Reload Timer)
72
Internal data bus
Timer counter D
(TCD)
HD404639R Series
Input capture
status flag (ICSF)
Input capture
error flag (ICEF)
Timer D interrupt
request flag (IFTD)
Error
control
logic
Timer read
register DU
(TRDU)
Timer read
register DL
(TRDL)
EVND
Edge
detection
logic
Read signal
Clock
Timer counter D
(TCD)
Overflow
System
clock
÷2048
3
÷512
÷128
÷32
÷8
÷4
÷2
Selector
Timer mode
register D1
(TMD1)
Internal data bus
Input capture
timer control
øPER
Prescaler S (PSS)
Timer mode
register D2
(TMD2)
Edge detection control
2
Edge detection
selection register
2 (ESR2)
Figure 58 (B) Block Diagram of Timer D (Input Capture Timer)
Timer D Operations:
• Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register D1 (TMD1: $010).
73
HD404639R Series
Timer D is initialized to the value set in timer write register D (TWDL: $011, TWDU: $012) by
software and incremented by one at each clock input. If an input clock is applied to timer D after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer D is
initialized to its initial value set in timer write register D; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
The overflow sets the timer D interrupt request flag (IFTD: $003, bit 0). IFTD is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
• External event counter operation: Timer D is used as an external event counter by selecting the
external event input as an input clock source. In this case, pin R40/EVND must be set to EVND by port
mode register C (PMRC: $025).
Either falling or rising edge, or both falling and rising edges of input signals can be selected as the
external event detection edge by detection edge select register 2 (ESR2: $027). When both rising and
falling edges detection is selected, the time between the falling edge and rising edge of input signals
must be 2t cyc or longer.
Timer D is incremented by one at each detection edge selected by detection edge select register 2
(ESR2: $027). The other operations are basi cally the same as the free-running/reload timer operation.
• Timer output operation: The following four output modes can be selected for timer D by setting timer
mode register D2 (TMD2: $015).
Toggle
0 output
1 output
PWM output
By selecting the timer output mode, pin R32/TOD is set to TOD. The output from TOD is reset low by
MCU reset.
 Toggle output: The operation is basically the same as that of timer-B’s toggle output.
 0 output: The operation is basically the same as that of timer-B’s 0 output.
 1 output: The operation is basically the same as that of timer-B’s 1 output.
 PWM output: The operation is basically the same as that of timer-C’s PWM output.
• Input capture timer operation: The input capture timer counts the clock cycles between trigger edges
input to pin EVND.
Either falling or rising edge, or both falling and rising edges of input signals can be selected as the
trigger input edge by detection edge select register 2 (ESR2: $027).
When a trigger edge is input to EVND, the count of timer D is written to timer read register D (TRDL:
$011, TRDU: $012), and the timer D interrupt request flag (IFTD: $003, bit 0) and the input capture
status flag (ICSF: $021, bit 0) are set. Timer D is reset to $00, and then incremented again. While
ICSF is set, if a trigger input edge is applied to timer D, or if timer D generates an overflow, the input
capture error flag (ICEF: $021, bit 1) is set. ICSF and ICEF are reset to 0 by MCU reset or by writing
0.
By selecting the input capture operation, pin R3 2/TOD is set to R3 2 and timer D is reset to $00.
74
HD404639R Series
Registers for Timer D Operation: By using the following registers, timer D operation modes are selected
and the timer D count is read and written.
Timer mode register D1 (TMD1: $010)
Timer mode register D2 (TMD2: $015)
Timer write register D (TWDL: $011, TWDU: $012)
Timer read register D (TRDL: $011, TRDU: $012)
Port mode register C (PMRC: $025)
Detection edge select register 2 (ESR2: $027)
• Timer mode register D1 (TMD1: $010): Four-bit write-only register that selects the freerunning/reload timer function, input clock source, and the prescaler division ratio as shown in figure 59.
It is reset to $0 by MCU reset.
Writing to this register is valid from the second instruction execution cycle after the execution of the
previous timer mode register D1 (TMD1: $010) write instruction. Setting timer D’s initialization by
writing to timer write register D (TWDL: $011, TWDU: $012) must be done after a mode change
becomes valid.
When selecting the input capture timer operation, select the internal clock as the input clock source.
Timer mode register D1 (TMD1: $010)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
TMD13
TMD12
TMD11
TMD10
Bit name
TMD13
Free-running/reload timer selection
0
Free-running timer
1
Reload timer
Input clock period and
input clock source
TMD12
TMD11
TMD10
0
0
0
2048tcyc
1
512tcyc
0
128tcyc
1
32tcyc
0
8tcyc
1
4tcyc
0
2tcyc
1
R40/EVND (External event input)
1
1
0
1
Figure 59 Timer Mode Register D1 (TMD1)
75
HD404639R Series
• Timer mode register D2 (TMD2: $015): Four-bit read/write register that selects the timer D output
mode and input capture operation as shown in figure 60. It is reset to $0 by MCU reset.
Timer mode register D2 (TMD2: $015)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
R/W
R/W
R/W
R/W
TMD23
TMD22
TMD21
TMD20
TMD23
TMD22
TMD21
TMD20
0
0
0
0
R32
R32 port
1
TOD
Toggle output
0
TOD
0 output
1
TOD
1 output
0
TOD
Inhibited
1
TOD
0
TOD
1
TOD
PWM output
R32
Input capture (R32 port)
1
1
0
1
1
R32/TOD mode selection
Don’t care Don’t care Don’t care
Figure 60 Timer Mode Register D2 (TMD2)
• Timer write register D (TWDL: $011, TWDU: $012): Write-only register consisting of a lower digit
(TWDL) and an upper digit (TWDU) as shown in figures 61 and 62. The operation of timer write
register D is basically the same as that of timer write register B (TWBL: $00A, TWBU: $00B).
Timer write register D (lower digit) (TWDL: $011)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
TWDL3
TWDL2
TWDL1
TWDL0
Bit name
Figure 61 Timer Write Register D Lower Digit (TWDL)
76
HD404639R Series
Timer write register D (upper digit) (TWDU: $012)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
W
W
W
W
TWDU3
TWDU2
TWDU1
TWDU0
Figure 62 Timer Write Register D Upper Digit (TWDU)
• Timer read register D (TRDL: $011, TRDU: $012): Read-only register consisting of a lower digit
(TRDL) and an upper digit (TRDU) as shown in figures 63 and 64. The operation of timer read register
D is basically the same as that of timer read register B (TRBL: $00A, TRBU: $00B).
When the input capture timer operation is selected and if the count of timer D is read after a trigger is
input, either the lower or upper digit can be read first.
Timer read register D (lower digit) (TRDL: $011)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRDL3
TRDL2
TRDL1
TRDL0
Figure 63 Timer Read Register D Lower Digit (TRDL)
Timer read register D (upper digit) (TRDU: $012)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
TRDU3
TRDU2
TRDU1
TRDU0
Figure 64 Timer Read Register D Upper Digit (TRDU)
• Port mode register C (PMRC: $025): Write-only register that selects R40/EVND pin function as shown
in figure 50. It is reset to $0 by MCU reset.
• Detection edge select register 2 (ESR2: $027): Write-only register that selects the detection edge of
signals input to pin EVND as shown in figure 65. It is reset to $0 by MCU reset.
77
HD404639R Series
Detection edge selection register 2 (ESR2: $027)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
ESR23
ESR22
ESR21
ESR20
Bit name
EVND detection edge
ESR23
ESR22
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
INT 4 detection edge
ESR21
ESR20
0
0
No detection
1
Falling-edge detection
0
Rising-edge detection
1
Double-edge detection *
1
Note: * Both falling and rising edges are detected.
Figure 65 Detection Edge Select Register 2 (ESR2)
Notes on Use
When using the timer output as PWM output, note the following point. From the update of the timer write
register until the occurrence of the overflow interrupt, the PWM output differs from the period and duty
settings, as shown in table 25. The PWM output should therefore not be used until after the overflow
interrupt following the update of the timer write register. After the overflow, the PWM output will have the
set period and duty cycle.
78
HD404639R Series
Table 25 PWM Output Following Update of Timer Write Register
PWM Output
Mode
Timer Write Register is Updated during
High PWM Output
Timer write
register
updated to
value N
Free running
Timer Write Register is Updated during
Low PWM Output
Timer write
register
updated to
value N
Interrupt
request
T × (255 – N) T × (N + 1)
Interrupt
request
T × (N' + 1)
T × (255 – N)
Reload
Timer write
register
updated to
value N
T
Interrupt
request
T × (255 – N)
T
Timer write
register
updated to
value N
T × (N + 1)
Interrupt
request
T
T × (255 – N)
T
79
HD404639R Series
Serial Communications Interface
The MCU has two channels of serial interface. The transfer and receive start instructions differ according to
the serial interface channel, but other functions are the same. The serial interface serially transfers or
receives 8-bit data, and includes the following features.
• Multiple transmit clock sources
 External clock
 Internal prescaler output clock
 System clock
• Output level control in idle states
Five registers, an octal counter, and a multiplexer are also configured for serial interfaces 1 and 2 as
follows.
Serial interface 1
•
•
•
•
•
•
•
Serial data register 1 (SR1L: $006, SR1U: $007)
Serial mode register 1A (SM1A: $005)
Serial mode register 1B (SM1B: $028)
Port mode register A (PMRA: $004)
Miscellaneous register (MIS: $00C)
Octal counter (OC1)
Selector
Serial interface 2
•
•
•
•
•
•
Serial data register 2 (SR2L: $01D, SR2U: $01E)
Serial mode register 2A (SM2A: $01B)
Serial mode register 2B (SM2B: $01C)
Port mode register A (PMRA: $004)
Octal counter (OC2)
Selector
The block diagram of the serial interface is shown in figure 66.
80
HD404639R Series
Serial interrupt
request flag
(IFS1, IFS2)
Octal counter
(OC1, OC2)
Idle control
logic
SO1 , SO2
SCK1 , SCK2
Transfer
control
1/2
1/2
System
clock
øPER
3
÷2048
÷512
÷128
÷32
÷8
÷2
Selector
Selector
SI1 , SI 2
Internal data bus
Serial data
register (SR1L/U,
SR2L/U)
Clock
I/O control
logic
Prescaler S (PSS)
Serial mode register
1A, 2A (SM1A,
SM2A)
Serial mode register
1B, 2B (SM1B,
SM2B)
Figure 66 Block Diagram of Serial Interface Serial Interface Operation
Serial Interface Operation
Selecting and Changing the Operating Mode: Tables 26 (A) and 26 (B) list the serial interfaces’
operating modes. To select an operating mode, use one of these combinations of port mode register A
(PMRA: $004), serial mode register 1A (SM1A: $005), and serial mode register 2A (SM2A: $01B)
settings; to change the operating mode of serial interface 1, always initialize the serial interface internally
by writing data to serial mode register 1A; and to change the operating mode of serial interface 2, always
initialize the serial interface internally by writing data to serial mode register 2A. Note that serial interface
81
HD404639R Series
1 is initialized by writing data to serial mode register 1A, and serial interface 2 is initialized by writing data
to serial mode register 2A. Refer to the following section Registers for Serial Interface for details.
Pin Setting: The R41/SCK 1 pin is controlled by writing data to serial mode register 1A (SM1A: $005). The
R5 1/SCK 2 pin is controlled by writing data to serial mode register 2A (SM2A: $01B). Pins R42/SI1,
R4 3/SO 1, R5 2/SI 2, and R5 3/SO 2 are controlled by writing data to port mode register A (PMRA: $004). Refer
to the following section Registers for Serial Interface for details.
Transmit Clock Source Setting: The transmit clock source of serial interface 1 is set by writing data to
serial mode register 1A (SM1A: $005) and serial mode register 1B (SM1B: $028). The transmit clock
source of serial interface 2 is set by writing data to serial mode register 2A (SM2A: $01B) and serial mode
register 2B (SM2B: $01C). Refer to the following section Registers for Serial Interface for details.
Data Setting: Transmit data of serial interface 1 is set by writing data to serial data register 1 (SR1L: $006,
SR1U: $007). Transmit data of serial interface 2 is set by writing data to serial data register 2 (SR2L: $01D,
SR2U: $01E). Receive data of serial interface 1 is obtained by reading the contents of serial data register 1.
Receive data of serial interface 2 is obtained by reading the contents of serial data register 2. The serial data
is shifted by each serial interface transmit clock and is input from or output to an external system.
The output level of the SO1 and SO2 pins is invalid until the first data of each serial interface is output after
MCU reset, or until the output level control in idle states is performed.
Transfer Control: Serial interface 1 is activated by the STS instruction. Serial interface 2 is activated by a
dummy read of serial mode register 2A (SM2A: $01B), which will be referred to as SM2A read. The octal
counter is reset to 000 by the STS instruction (serial interface 2 is SM2A read), and it increments at the
rising edge of the transmit clock for each serial interface. When the eighth transmit clock signal is input or
when serial transmission/reception is discontinued, the octal counter is reset to 000, the serial interface 1
interrupt request flag (IFS1: $003, bit 2) for serial interface 1 and serial interface 2 interrupt request flag
(IFS2: $023, bit 2) for serial interface 2 are set, and the transfer stops.
When the prescaler output is selected as the transmit clock of serial interface 1, the transmit clock
frequency is selected as 4t cyc to 8192tcyc by setting bits 0 to 2 (SM1A0–SM1A2) of serial mode register 1A
(SM1A: $005) and bit 0 (SM1B0) of serial mode register 1B (SM1B: $028) as listed in table 27. When the
prescaler output is selected as the transmit clock of serial interface 2, the transmit clock frequency is
selected as 4tcyc to 8192tcyc by setting bits 0 to 2 (SM2A0–SM2A2) of serial mode register 2A (SM2A:
$01B) and bit 0 (SM2B0) of serial mode register 2B (SM2B: $01C).
Note: To start serial interface 2, simply read serial mode register 2A by using the instruction that compares
serial mode register 2A with the accumulator.
Serial mode register 2A is a read-only register, so $0 can be read.
82
HD404639R Series
Table 26 (A) Serial Interface 1 Operating Modes
SM1A
PMRA
Bit 3
Bit 1
Bit 0
Operating Mode
1
0
0
Continuous clock output mode
1
Transmit mode
0
Receive mode
1
Transmit/receive mode
1
Table 26 (B) Serial Interface 2 Operating Modes
SM2A
PMRA
Bit 3
Bit 1
Bit 0
Operating Mode
1
0
0
Continuous clock output mode
1
Transmit mode
0
Receive mode
1
Transmit/receive mode
1
Table 27 Transmit Clock (Prescaler Output)
SM1B/
SM2B
SM1A/ SM2A
Bit 0
Bit 2
Bit 1
Bit 0
Prescaler Division Ratio
Transmit Clock Frequency
0
0
0
0
÷ 2048
4096t cyc
1
÷ 512
1024t cyc
0
÷ 128
256t cyc
1
÷ 32
64t cyc
0
÷8
16t cyc
1
÷2
4t cyc
0
÷ 4096
8192t cyc
1
÷ 1024
2048t cyc
0
÷ 256
512t cyc
1
÷ 64
128t cyc
0
÷ 16
32t cyc
1
÷4
8t cyc
1
1
1
0
0
0
1
1
0
83
HD404639R Series
Operating States: Serial interface 1 has the following operating states; transitions between them are shown
in figure 67.
•
•
•
•
STS wait state (serial interface 2 is in SM2A read wait state)
Transmit clock wait state
Transfer state
Continuous clock output state (only in internal clock mode)
System reset
STS instruction wait state
(with octal counter = 000,
transmit clock disabled)
00
SM1A write
04
STS instruction*
SM1A write
(IFS1 ← 1)
01
Transmit clock
06
02
Transfer state
(octal counter ≠ 000)
Transmit clock wait state
(octal counter = 000)
Eight transmit clock cycles
STS instruction* 05
(IFS1 ← 1)
03
External Clock Mode
System reset
SM1A write
Transmit clock
continuous output state
(PMRA 0, 1 = 00)
Transmit clock
STS instruction wait state
(with octal counter = 000,
transmit clock disabled)
10
18
SM1A write
14
STS instruction* 11
Eight transmit clock cycles
STS instruction 16
(IFS1 ← 1)
13
17
Transmit clock 12
Transmit clock wait state
(octal counter = 000)
Transfer state
(octal counter ≠ 000)
STS instruction * 15
(IFS1 ← 1)
Internal Clock Mode
Note: * For serial interface 2, this is accomplished by reading the SM2A register.
Circled numbers are referred to in the text.
Figure 67 Serial Interface State Transition Diagram
The operation state of serial interface 2 is the same as serial interface 1 except that the STS instruction of
serial interface 1 changes to SM2A read. The following shows the operation state of serial interface 1.
• STS wait state: The serial interface enters STS wait state by MCU reset (00, 10 in figure 67). In STS
wait state, serial interface 1 is initialized and the transmit clock is ignored. If the STS instruction is then
executed (01, 11), serial interface 1 enters transmit clock wait state.
84
HD404639R Series
• Transmit clock wait state: Transmit clock wait state is the period between the STS execution and the
falling edge of the first transmit clock. In transmit clock wait state, input of the transmit clock (02, 12)
increments the octal counter, shifts serial data register 1 (SR1L: $006, SR1U: $007), and puts the serial
interface in transfer state. However, note that if continuous clock output mode is selected in internal
clock mode, the serial interface does not enter transfer state but enters continuous clock output state
(17).
The serial interface enters STS wait state by writing data to serial mode register 1A (SM1A: $005) (04,
14) in transmit clock wait state.
• Transfer state: Transfer state is the period between the falling edge of the first clock and the rising edge
of the eighth clock. In transfer state, the input of eight clocks or the execution of the STS instruction
sets the octal counter to 000, and the serial interface enters another state. When the STS instruction is
executed (05, 15), transmit clock wait state is entered. When eight clocks are input, transmit clock wait
state is entered (03) in external clock mode, and STS wait state is entered (13) in internal clock mode. In
internal clock mode, the transmit clock stops after outputting eight clocks.
In transfer state, writing data to serial mode register 1A (SM1A: $005) (06, 16) initializes serial
interface 1, and STS wait state is entered.
If the state changes from transfer to another state, the serial 1 interrupt request flag (IFS1: $003, bit 2) is
set by the octal counter that is reset to 000.
• Continuous clock output state (only in internal clock mode): Continuous clock output state is entered
only in internal clock mode. In this state, the serial interface does not transmit/receive data but only
outputs the transmit clock from the SCK 1 pin.
When bits 0 and 1 (PMRA0, PMRA1) of port mode register A (PMRA: $004) are 00 in transmit clock
wait state and if the transmit clock is input (17), the serial interface enters continuous clock output state.
If serial mode register 1A (SM1A: $005) is written to in continuous clock output mode (18), STS wait
state is entered.
Output Level Control in Idle States: When serial interface 1 is in STS instruction wait state and when
serial interface 2 is in SM2A read wait state and transmit clock state, the output of each serial output pin,
SO1 and SO2, can be controlled by setting bit 1 (SM1B1) of serial mode register 1B (SM1B: $028) to 0 or
1, or bit 1 (SM2B1) of serial mode register 2B (SM2B: $01C) to 0 or 1. The output level control example
of serial interface 1 is shown in figure 68. Note that the output level cannot be controlled in transfer state.
85
HD404639R Series
Transmit clock
wait state
State
STS wait state
Transmit clock
wait state
Transfer state
STS wait state
MCU reset
Port selection
PMRA write
External clock selection
Dummy write for
state transition
SM1A write
Output level control in
idle states
Output level control in
idle states
SM1B write
Data write for transmission
SR1L, SR1U
write
STS instruction
SCK1 pin (input)
SO1 pin
LSB
Undefined
MSB
IFS1
External clock mode
Flag reset at transfer completion
Transmit clock
wait state
State
STS wait state
Transfer state
STS wait state
MCU reset
Port selection
PMRA write
Internal clock selection
SM1A write
Output level control in
idle states
Output level control in
idle states
SM1B write
Data write for transmission
SR1L, SR1U
write
STS instruction
SCK1 pin (output)
SO1 pin
Undefined
LSB
MSB
IFS1
Internal clock mode
Flag reset at transfer completion
Figure 68 Example of Serial Interface 1 Operation Sequence
86
HD404639R Series
Transmit Clock Error Detection (In External Clock Mode): Each serial interface will malfunction if a
spurious pulse caused by external noise conflicts with a normal transmit clock during transfer. A transmit
clock error of this type can be detected as shown in figure 69.
If more than eight transmit clocks are input in transfer state, at the eighth clock including a spurious pulse
by noise, the octal counter reaches 000, the serial 1 interrupt request flag (IFS1: $003, bit 2) is set, and
transmit clock wait state is entered. At the falling edge of the next normal clock signal, the transfer state is
entered. After the transfer is completed and IFS1 is reset, writing to serial mode register 1A (SM1A: $005)
changes the state from transfer to STS wait. At this time serial interface 1 is in the transfer state, and the
serial 1 interrupt request flag is set again, and therefore the error can be detected. The same applies to serial
interface 2.
87
HD404639R Series
Transfer completion
(IFS1 ← 1)
Interrupts inhibited
IFS1 ← 0
SM1A write
Yes
IFS1 = 1
Transmit clock
error processing
No
Normal
termination
Transmit clock error detection flowchart
State
Transmit
clock
wait state
Transmit clock
wait state
Transfer state
SCK 1 pin
(input)
Transfer state
Noise
1
2
3
4
5
6
7
8
Transfer state has been
entered by the transmit
clock error. When SM1A is
written,IFS1 is set.
SM1A
write
IFS1
Flag set because octal
counter reaches 000.
Transmit clock error detection procedures
Figure 69 Transmit Clock Error Detection
88
Flag reset at
transfer completion.
HD404639R Series
Notes on Use:
• Initialization after writing to registers: If port mode register A (PMRA: $004) is written to in transmit
clock wait state or in transfer state, the serial interface must be initialized by writing to serial mode
register 1A (SM1A: $005) and serial mode register 2A (SM2A: $01B) again.
• Serial 1 interrupt request flag (IFS1: $003, bit 2) and serial 2 interrupt request flag (IFS2: $023, bit 2)
set: For serial interface 1, if the state is changed from transfer state to another by writing to serial mode
register 1A (SM1A: $005) or executing the STS instruction during the first low pulse of the transmit
clock, the serial 1 interrupt request flag (IFS1: $003, bit 2) is not set. In the same way for serial interface
2, if the state is changed from transfer state to another by writing to serial mode register 2A (SM2A:
$01B) or by executing the STS instruction during the first low pulse of the transmit clock, the serial 2
interrupt request flag is not set. To set the serial 1 interrupt request flag, a serial mode register 1A write
or STS instruction execution must be programmed to be executed after confirming that the SCK 1 pin is
at 1, that is, after executing the input instruction to port R4. To set the serial 2 interrupt request flag, a
serial mode register 2A write or SM2A instruction execution must be programmed to be executed after
confirming that the SCK 2 pin is at 1, that is, after executing the input instruction to port R5.
Registers for Serial Interface
When serial interface operation is selected, serial data is read and written by the following registers.
For serial interface 1
•
•
•
•
•
Serial mode register 1A (SM1A: $005)
Serial mode register 1B (SM1B: $028)
Serial data register 1 (SR1L: $006, SR1U: $007)
Port mode register A (PMRA: $004)
Miscellaneous register (MIS: $00C)
For serial interface 2
•
•
•
•
Serial mode register 2A (SM2A: $01B)
Serial mode register 2B (SM2B: $01C)
Serial data register 2 (SR2L: $01D, SR2U: $01E)
Port mode register A (PMRA: $004)
Serial Mode Register 1A (SM1A: $005): This register has the following functions (figure 70).
•
•
•
•
R4 1/SCK 1 pin function selection
Serial interface 1 transmit clock selection
Serial interface 1 prescaler division ratio selection
Serial interface 1 initialization
Serial mode register 1A is a 4-bit write-only register. It is reset to $0 by MCU reset.
89
HD404639R Series
A write signal input to serial mode register 1A discontinues the input of the transmit clock to serial data
register 1 (SR1L: $006, SR1U: $007) and the octal counter, and the octal counter is reset to 000. Therefore,
if a write is performed during data transfer, the serial 1 interrupt request flag (IFS1: $003, bit 2) is set.
Written data is valid from the second instruction execution cycle after the write operation, so the STS
instruction must be executed at least two cycles after that.
Serial mode register 1A (SM1A: $005)
Bit
3
2
0
1
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM1A3
SM1A2
SM1A1
SM1A0
Bit name
SM1A3
R41/SCK1
mode selection
0
R41
1
SCK1
Prescaler
division ratio
SM1A2
SM1A1
SM1A0
SCK1
Clock source
0
0
0
Output
Prescaler
Refer to
table 27
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
1
0
0
1
1
Figure 70 Serial Mode Register 1A (SM1A)
Serial Mode Register 1B (SM1B: $028): This register has the following functions (figure 71).
• Serial interface 1 prescaler division ratio selection
• Serial interface 1 output level control in idle states
Serial mode register 1B (SM1B: $028) is a 2-bit write-only register. It cannot be written during data
transfer.
By setting bit 0 (SM1B0) of this register, the serial interface 1 prescaler division ratio is selected. Only bit 0
(SM1B0) can be reset to 0 by MCU reset. By setting bit 1 (SM1B1), the output level of the SO 1 pin is
controlled in idle states of serial interface 1. The output level changes at the same time that SM1B1 is
written to.
90
HD404639R Series
Serial mode register 1B (SM1B: $028)
Bit
3
2
1
0
Initial value
—
—
Undefined
0
Read/Write
—
—
W
W
Bit name
Not used Not used SM1B1
SM1B1
Output level control in idle states
SM1B0
SM1B0
Transmit clock division ratio
0
Low level
0
Prescaler output divided by 2
1
High level
1
Prescaler output divided by 4
Figure 71 Serial Mode Register 1B (SM1B)
Serial Data Register 1 (SR1L: $006, SR1U: $007): This register has the following functions (figures 72
and 73)
• Serial interface 1 transmission data write and shift
• Serial interface 1 receive data shift and read
Writing data in this register is output from the SO1 pin, LSB first, synchronously with the falling edge of
the transmit clock; data is input, LSB first, through the SI1 pin at the rising edge of the transmit clock.
Input/output timing is shown in figure 74.
Data cannot be read or written during serial data transfer. If a read/write occurs during transfer, the
accuracy of the resultant data cannot be guaranteed.
Serial data register 1 (lower digit) (SR1L: $006)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR13
SR12
SR11
SR10
Figure 72 Serial Data Register 1 (SR1L)
Serial data register 1 (upper digit) (SR1U: $007)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR17
SR16
SR15
SR14
Figure 73 Serial Data Register 1 (SR1U)
91
HD404639R Series
Transmit clock
1
Serial output
data
2
3
4
5
6
LSB
Serial input data
latch timing
Figure 74 Serial Interface Output Timing
92
7
8
MSB
HD404639R Series
Port Mode Register A (PMRA: $004): This register has the following functions (figure 75).
•
•
•
•
R4 2/SI 1 pin function selection
R4 3/SO 1 pin function selection
R5 2/SI 2 pin function selection
R5 3/SO 2 pin function selection
Port mode register A (PMRA: $004) is a 4-bit write-only register, and is reset to $0 by MCU reset.
Port mode register A (PMRA: $004)
Bit
3
2
1
0
Initial value
0
0
0
0
W
W
W
Read/Write
Bit name
W
PMRA3
PMRA2 PMRA1 PMRA0
PMRA0
R43/SO1 mode selection
0
R43
1
SO1
PMRA1
R42/SI1 mode selection
0
R42
1
SI1
PMRA2
R53/SO2 mode selection
0
R53
1
SO2
PMRA3
R52/SI2 mode selection
0
R52
1
SI2
Figure 75 Port Mode Register A (PMRA)
Miscellaneous Register (MIS: $00C): This register has the following functions (figure 76).
• R4 3/SO 1 pin PMOS control
Miscellaneous register (MIS: $00C) is a 4-bit write-only register and is reset to $0 by MCU reset.
93
HD404639R Series
Miscellaneous register (MIS: $00C)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
MIS3
MIS2
MIS1
MIS0
Bit name
MIS1
MIS0
0
0
tRC
0.12207 ms
0.24414 ms*
1
MIS2
1
7.8125 ms
0
31.25 ms
1
Not used
R43/SO1 PMOS on/off selection
0
On
1
Off
MIS3
Pull-up MOS on/off selection
0
Off
1
On
Note: * This value is valid only for direct transfer operation.
Figure 76 Miscellaneous Register (MIS)
Serial Mode Register 2A (SM2A: $01B): This register has the following functions (figure 77).
•
•
•
•
R5 1/SCK 2 pin function selection
Serial interface 2 transmit clock selection
Serial interface 2 prescaler division ratio selection
Serial interface 2 initialization
Serial mode register 2A (SM2A: $01B) is a 4-bit write-only register. It is reset to $0 by MCU reset.
A write signal input to serial mode register 2A discontinues the input of the transmit clock to serial data
register 2 (SR2L: $01D, SR2U: $01E) and the octal counter, and the octal counter is reset to 000.
Therefore, if a write is performed during data transfer, the serial 2 interrupt request flag (IFS2: $023, bit 2)
is set.
Written data is valid from the second instruction execution cycle after the write operation, so the SM2A
read instruction must be executed at least two cycles after that.
94
HD404639R Series
Serial mode register 2A (SM2A: $01B)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SM2A3
SM2A2
SM2A1
SM2A0
Bit name
SM2A3
R51/SCK2
mode selection
0
R51
1
SCK2
Prescaler
division ratio
SM2A2
SM2A1
SM2A0
SCK2
Clock source
0
0
0
Output
Prescaler
Refer to
table 27
0
Output
System clock
—
1
Input
External clock
—
1
1
0
1
1
0
0
1
1
Figure 77 Serial Mode Register 2A (SM2A)
Serial Mode Register 2B (SM2B: $01C): This register has the following functions (figure 78).
• Serial interface 2 prescaler division ratio selection
• Serial interface 2 output level control in idle states
• R5 3/SO 2 pin PMOS control
Serial mode register 2B is a 3-bit write-only register. It cannot be written during serial interface 2 data
transfer. Bit 0 (SM2B0) and bit 2 (SM2B2) are reset to $0 by MCU reset.
By setting bit 0 (SM2B0) of this register, the serial interface 2 prescaler division ratio of serial interface 2 is
selected. By resetting bit 1 (SM2B1), the output level of the SO2 pin is controlled in idle states of serial
interface 2. The output level changes at the same time that SM2B1 is written to.
95
HD404639R Series
Serial mode register 2B (SM2B: $01C)
Bit
3
2
1
0
Initial value
—
0
Undefined
0
Read/Write
—
W
W
W
SM2B1
SM2B0
Bit name
SM2B2
Not used SM2B2
SM2B0
R53 /SO 2 PMOS
Transmit clock division ratio
0
On
0
Prescaler output divided by 2
1
Off
1
Prescaler output divided by 4
SM2B1
Output level control in idle states
0
Low level
1
High level
Figure 78 Serial Mode Register 2B (SM2B)
Serial Data Register 2 (SR2L: $01D, SR2U: $01E): This register has the following functions (figures 79
and 80).
• Serial interface 2 transmission data write and shift
• Serial interface 2 receive data shift and read
Writing data in this register is output from the SO2 pin, LSB first, synchronously with the falling edge of
the transmit clock; data is input, LSB first, through the SI2 pin at the rising edge of the transmit clock.
Data cannot be read or written during serial data transfer. If a read/write occurs during transfer, the
accuracy of the resultant data cannot be guaranteed.
Serial data register 2 (lower digit) (SR2L: $01D)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR23
SR22
SR21
SR20
Figure 79 Serial Data Register 2 (SR2L)
96
HD404639R Series
Serial data register 2 (upper digit) (SR2U: $01E)
Bit
3
Initial value
2
1
0
Undefined Undefined Undefined Undefined
Read/Write
R/W
R/W
R/W
R/W
Bit name
SR27
SR26
SR25
SR24
Figure 80 Serial Data Register 2 (SR2U)
97
HD404639R Series
DTMF Generator Circuit
The MCU provides a dual-tone multifrequency (DTMF) generator circuit. The DTMF signal consists of
two sine waves to access the switching system.
Figure 81 shows the DTMF keypad and frequencies. Each key enables tones to be generated corresponding
to each frequency. Figure 82 shows a block diagram of the DTMF circuit.
The OSC clock (400 kHz, 800 kHz, 2 MHz, 3.58 MHz, 4 MHz, 7.16 MHz or 8 MHz) is changed into six
clock signals through the division circuit (1/2, 1/5, 1/9, 1/10, 1/18 and 1/20). The DTMF circuit uses one
of the six clock signals, which is selected by system clock select register 1 (SSR1: $029) and system clock
select register 2 (SSR2: $02A) depending on the OSC clock frequency. The DTMF circuit has
transformed programmable dividers, sine wave counters, and control registers.
1
2
3
A
R1 (697 Hz)
4
5
6
B
R2 (770 Hz)
7
8
9
C
R3 (852 Hz)
*
0
#
D
R4 (941 Hz)
C1 (1,209 Hz)
C2 (1,336 Hz)
C3 (1,477 Hz)
C4 (1,633 Hz)
The DTMF generator circuit is controlled by the following three registers.
Figure 81 DTMF Keypad and Frequencies
98
HD404639R Series
Transformation program
divider
2
Feedback
VT ref
Tone generator
mode register
(TGM)
TONER output control
Transformation program
divider
Sine wave
counter D/A
TONEC
2
Feedback
Tone generator
control register
(TGC)
TONEC output control
2
f OSC
Internal data bus
Sine wave
counter D/A
TONER
400 kHz
800 kHz
1/2
2 MHz
1/5
3.58 MHz
1/9*3
400 kHz *3
System clock
selection register 1
(SSR1)
Selector
4 MHz
1/10
7.16 MHz*2
8
1/18*3
System clock
selection register 2
(SSR2) *1
MHz*2
1/20
1
Notes: 1. System clock selection register 2 (SSR2) is used to specify the divide-by-9 or divide-by-18 operation
when a 3.58-MHz or 7.16 MHz system clock oscillator is used.
2. Applies to HD40A4638R, HD40A4639R and HD407A4639R.
3. This is 397.8 kHz when fOSC is 3.58 MHz and 7.16 MHz.
Figure 82 Block Diagram of DTMF Generator Circuit
99
HD404639R Series
Tone Generator Mode Register (TGM: $019): Four-bit write-only register, which controls output
frequencies as shown in figure 83, and is reset to $0 by MCU reset.
Tone generator mode register (TGM: $019)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
Bit name
W
W
W
W
TGM3
TGM2
TGM1
TGM0
TGM3
TGM2
0
0
0
TONEC output frequencies
TGM1
TGM0
TONER output frequencies
f C1 (1,209 Hz)
0
0
f R1 (697 Hz)
1
f C2 (1,336 Hz)
0
1
f R2 (770 Hz)
1
0
f C3 (1,477 Hz)
1
0
f R3 (852 Hz)
1
1
f C4 (1,633 Hz)
1
1
f R4 (941 Hz)
Figure 83 Tone Generator Mode Register (TGM)
Tone Generator Control Register (TGC: $01A): Three-bit write-only register, which controls the
start/stop of the DTMF signal output as shown in figure 84, and is reset to $0 by MCU reset. TONER and
TONEC output can be independently controlled by bits 2 and 3 (TGC2, TGC3), and the DTMF circuit is
controlled by bit 1 (TGC1) of this register.
Tone generator control register (TGC: $01A)
Bit
3
2
1
0
Initial value
0
0
0
—
Read/Write
W
W
W
—
TGC3
TGC2
TGC1
Not used
TONEC output control (column)
TGC1
Bit name
TGC3
DTMF enable bit
0
No output
0
DTMF disable
1
TONEC output (active)
1
DTMF enable
TGC2
TONER output control (row)
0
No output
1
TONER output (active)
Figure 84 Tone Generator Control Register (TGC)
100
HD404639R Series
System Clock Select Registers 1 and 2 (SSR1: $029, SSR2: $02A): Four-bit write-only registers.
These registers must be set to the value specified in figures 85 and 86 depending on the frequency of the
oscillator connected to the OSC1 and OSC2 pins. Note that if the combination of the oscillation frequency
and the values in these registers is different from that specified in figures 85 and 86, the DTMF output
frequencies will differ from the correct frequencies as listed in table 28.
System clock select register 1 (SSR1: $029)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SSR13
SSR12
SSR11
SSR10
Bit name
SSR13 32-kHz oscillation stop
0
Oscillation operates in stop mode
1
Oscillation stops in stop mode
System clock
SSR23 SSR22 SSR11 SSR10 selection
0
0
32-kHz oscillation division
SSR12 ratio selection
0
f SUB = f X /8
1
f SUB = f X /4
0
1
1
1
0
1
0
400 kHz
1
800 kHz
0
2 MHz
1
4 MHz
Don’t care Don’t care 3.58 MHz
1
1
8 MHz
Don’t care Don’t care 7.16 MHz
Figure 85 System Clock Select Register 1(SSR1)
101
HD404639R Series
Serial clock select register 2 (SSR2: $02A)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
SSR23
SSR22
SSR21
SSR20
Bit name
SSR23 SSR22 System clock selection
0
1
SSR21 SSR20 System clock division ratio
0
Selected from 400 kHz, 800 kHz,
2 MHz, 4 MHz * 1
0
1
3.58 MHz
1
0
8 MHz
1
7.16 MHz
*1
0
1/4 division
1
1/8 division
0
1/16 division
1
1/32 division
Notes: 1. Refer to system clock select register 1 (SSR1) of figure 85.
2. The DTMF frequencies are not affected by the setting of the system clock division ratio.
Figure 86 System Clock Select Register 2(SSR2)
Table 28 Frequency Deviation of the MCU from Standard DTMF
fOSC = 400 kHz, 800 kHz, 2 MHz, 4 MHz,
8 MHz
fOSC = 3.58 MHz, 7.16 MHz
Standard
DTMF (Hz)
MCU (Hz)
Deviation from
Standard (%)
MCU (Hz)
Deviation from
Standard (%)
R1
697
694.44
–0.37
690.58
–0.92
R2
770
769.23
–0.10
764.96
–0.65
R3
852
851.06
–0.11
846.33
–0.67
R4
941
938.97
–0.22
933.75
–0.77
C1
1,209
1,212.12
0.26
1,205.39
–0.30
C2
1,336
1,333.33
–0.20
1,325.92
–0.75
C3
1,477
1,481.48
0.30
1,473.25
–0.25
C4
1,633
1,639.34
0.39
1,630.23
–0.17
Note: This frequency deviation value does not include the frequency deviation due to the oscillator
element. Also note that in this case the ratio of the high level and low level widths in the oscillator
waveform due to the oscillator element will be 50%:50%.
102
HD404639R Series
DTMF Output: The sine waves of the row-group and column-group are individually converted in the D/A
conversion circuit which provides a high-precision ladder resistance. The DTMF output pins (TONER,
TONEC) transmit the sine waves of the row-group and column-group, respectively. Figure 87 shows the
tone output equivalent circuit. Figure 88 shows the output waveform. One cycle of this wave consists of 32
slots. Therefore, the output waveform is stable with little distortion. Table 28 lists the frequency deviation
of the MCU from standard DTMF signals.
Switch control
VTref
GND
TONER
TONEC
Figure 87 Tone Output Equivalent Circuit
VTref
1 2 3 4 5 6 7 8 9 10 1112 13 14 15 16 17 18 19 20 2122 23 24 25 26 27 28 29 30 31 32
GND
Time slots
Figure 88 Waveform of Tone Output
103
HD404639R Series
Comparator
The block diagram of the comparator is shown in figure 89. The comparator compares input voltage with
the reference voltage. Internal voltage or external input voltage can be selected as the reference. Internal
reference voltage is selected from sixteen levels.
Setting bit 3 (CER3) of the compare enable register (CER: $018) to 1 executes a voltage comparison.
When an input voltage at COMP0–COMP3 is higher than the reference voltage, the TM or TMD command
sets the status flag (ST) high for the corresponding bits of the compare data register (CDR: $017) to
COMP0–COMP3. On the other hand, when an input voltage at COMP0–COMP3 is lower, the TM or TMD
command clears the ST to 0.
COMP1
COMP2
Selector
COMP3
+
VCref
Comparator
Comparator data
register (CDR)
–
2
Comparator enable
register (CER)
Selector
5R
R
R
Internal data bus
Selector
COMP0
R
2R
4
Comparator control
register (CCR)
Figure 89 Block Diagram of Comparator
Compare Enable Register (CER: $018): Four-bit write-only register which enables comparator
operation, and selects the reference voltage and the analog input pin.
Compare Control Register (CCR: $016): Four-bit write-only register which selects the internal reference
voltage from sixteen levels.
Compare Data Register (CDR: $017): Four-bit read-only register which latches the result of the
comparison between the analog input pins and the reference voltage. Bits 0 to 3 show the results of
comparison with COMP 0 –COMP 3 , respectively. This register can be read only by the TM or TMD
104
HD404639R Series
command. Only bit CER3 corresponds to the analog input pin selected with bits CER0 and CER1. After a
compare operation, the data in this register is not retained.
Note on Use: During the compare operation pins RD0/COMP0–RD3/COMP3 operate as analog inputs and
cannot operate as R ports.
The comparator can operate in active mode and subactive mode but is disabled in other modes.
The switch for the internal reference voltage is on only when the internal reference voltage is selected by
CER2.
RE0/VC ref cannot operate as an R port when the external input voltage is selected as the reference.
Compare enable register (CER: $018)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
CER3
CER2
CER1
CER0
Bit name
CER3
0
1
CER2
Digital/Analog selection
Digital input mode:
RD0 /COMP0–RD3 /COMP3
operate as R port
Analog input mode:
RD0 /COMP0–RD3 /COMP3
operate as analog input
CER1
CER0
0
0
COMP0
1
COMP1
0
COMP2
1
COMP3
1
Analog input pin selection
Reference voltage selection
0
External input voltage
1
Internal voltage
Figure 90 Compare Enable Register (CER)
105
HD404639R Series
Compare control register (CCR: $016)
Bit
3
2
1
0
Initial value
0
0
0
0
Read/Write
W
W
W
W
CCR3
CCR2
CCR1
CCR0
Bit name
CCR3
CCR2
CCR1
CCR0
0
0
0
0
2/22 VCC
1
3/22 VCC
0
4/22 VCC
1
5/22 VCC
0
6/22 VCC
1
7/22 VCC
0
8/22 VCC
1
9/22 VCC
0
10/22 VCC
1
11/22 VCC
0
12/22 VCC
1
13/22 VCC
0
14/22 VCC
1
15/22 VCC
0
16/22 VCC
1
17/22 VCC
1
1
0
1
1
0
0
1
1
0
1
Reference voltage selection
Figure 91 Compare Control Register (CCR)
106
HD404639R Series
Compare data register (CDR: $017)
Bit
Initial value
Read/Write
Bit name
3
2
1
0
Undefined Undefined Undefined Undefined
R
R
R
R
CDR3
CDR2
CDR1
CDR0
Result of COMP0 comparison
Result of COMP1 comparison
Result of COMP2 comparison
Result of COMP3 comparison
Figure 92 Compare Data Register (CDR)
107
HD404639R Series
Programmable ROM (HD407A4639R)
The HD407A4639R is a ZTAT microcomputer with built-in PROM that can be programmed in PROM
mode.
PROM Mode Pin Description
MCU Mode
PROM Mode
Pin No.
Pin Name
I/O
1
RD0/COMP0
I
2
RD1/COMP1
3
I/O Pin No.
PROM Mode
Pin Name
I/O Pin Name
26
D13/INT0
I
I
27
R0 0/INT1
I/O M0
I
RD2/COMP2
I
28
R0 1/INT2
I/O M1
I
4
RD3/COMP3
I
29
R0 2/INT3
I/O
5
RE 0/VCref
I
GND
30
R0 3/INT4
I/O
6
TEST
I
TEST
31
R1 0
I/O A5
I
7
OSC 1
I
VCC
32
R1 1
I/O A6
I
8
OSC 2
O
33
R1 2
I/O A7
I
9
RESET
I
RESET
34
R1 3
I/O A8
I
10
X1
I
GND
35
R2 0
I/O A0
I
11
X2
O
36
R2 1
I/O A10
I
12
GND
37
R2 2
I/O A11
I
13
D0
I/O
CE
I
38
R2 3
I/O A12
I
14
D1
I/O
OE
I
39
R3 0/TOB
I/O
15
D2
I/O
VCC
40
R3 1/TOC
I/O
16
D3
I/O
VCC
41
R3 2/TOD
I/O
17
D4
I/O
42
R3 3/EVNB
I/O
18
D5
I/O
43
R4 0/EVND
I/O
19
D6
I/O
44
R4 1/SCK 1
I/O
20
D7
I/O
45
R4 2/SI1
I/O
21
D8
I/O
46
R4 3/SO 1
I/O
22
D9
I/O
47
R5 0
I/O
23
D10
I/O
A13
I
48
R5 1/SCK 2
I/O
24
D11
I/O
A14
I
49
R5 2/SI2
I/O
25
D12/STOPC
I
A9
I
50
R5 3/SO 2
I/O
108
Pin Name
MCU Mode
I
I
GND
I/O
VPP
HD404639R Series
MCU Mode
PROM Mode
MCU Mode
PROM Mode
Pin No.
Pin Name
I/O
Pin Name
I/O Pin No.
Pin Name
I/O Pin Name
I/O
51
R6 0
I/O
A1
I
66
R9 3
I/O O1
I/O
52
R6 1
I/O
A2
I
67
RA 0
I/O O0
I/O
53
R6 2
I/O
A3
I
68
RA 1
I/O VCC
54
R6 3
I/O
A4
I
69
RA 2
I/O
55
R7 0
I/O
O0
I/O 70
RA 3
I/O
56
R7 1
I/O
O1
I/O 71
RB 0
I/O
57
R7 2
I/O
O2
I/O 72
RB 1
I/O
58
R7 3
I/O
O3
I/O 73
RB 2
I/O
59
R8 0
I/O
O4
I/O 74
RB 3
I/O
60
R8 1
I/O
O5
I/O 75
RC0
I/O
61
R8 2
I/O
O6
I/O 76
SEL
I
62
R8 3
I/O
O7
I/O 77
TONEC
O
63
R9 0
I/O
O4
I/O 78
TONER
O
64
R9 1
I/O
O3
I/O 79
VCC
VCC
65
R9 2
I/O
O2
I/O 80
VT ref
VCC
Notes: 1. I/O: Input/output pin, I: Input pin, O: Output pin
2. Each of O0–O4 has two pins; before using, each pair must be connected together.
Programming the Built-In PROM
The MCU’s built-in PROM is programmed in PROM mode. PROM mode is set by pulling TEST, M0, and
M1 low, and RESET high as shown in figure 93. In PROM mode, the MCU does not operate, but it can be
programmed in the same way as any other commercial 27256-type EPROM using a standard PROM
programmer and an 80-to-28-pin socket adapter. Recommended PROM programmers and socket adapters
of the HD407A4639 are listed in table 30.
Since an HMCS400-series instruction is ten bits long, the HMCS400-series MCU has a built-in conversion
circuit to enable the use of a general-purpose PROM programmer. This circuit splits each instruction into
five lower bits and five upper bits that are read from or written to consecutive addresses. This means that
if, for example, 16 kwords of built-in PROM are to be programmed by a general-purpose PROM
programmer, a 32-kbyte address space ($0000–$7FFF) must be specified.
Warnings
1. Always specify addresses $0000 to $7FFF when programming with a PROM programmer. If address
$8000 or higher is accessed, the PROM may not be programmed or verified correctly. Set all data in
unused addresses to $FF.
Note that the plastic-package version cannot be erased or reprogrammed.
109
HD404639R Series
2. Make sure that the PROM programmer, socket adapter, and LSI are aligned correctly (their pin 1
positions match), otherwise overcurrents may damage the LSI. Before starting programming, make
sure that the LSI is firmly fixed in the socket adapter and the socket adapter is firmly fixed onto the
programmer.
3. PROM programmers have two voltages (VPP ): 12.5 V and 21 V. Remember that ZTAT devices
require a VPP of 12.5 V—the 21-V setting will damage them. 12.5 V is the Intel 27256 setting.
Programming and Verification
The built-in PROM of the MCU can be programmed at high speed without risk of voltage stress or damage
to data reliability.
Programming and verification modes are selected as listed in table 29.
Table 29 PROM Mode Selection
Pin
Mode
CE
OE
VPP
O0–O7
Programming
Low
High
VPP
Data input
Verification
High
Low
VPP
Data output
Programming inhibited
High
High
VPP
High impedance
Table 30 Recommended PROM Programmers and Socket Adapters
PROM Programmer
Socket Adapter
Manufacturer
Model Name
Package
Manufacturer
Model Name
DATA I/O Corp.
121B
FP-80B
Hitachi
HS463ESF01H
AVAL Corp.
PKW-1000
110
HD404639R Series
VCC
VCC
RESET
VCC
TEST
M0
VPP
M1
O0 to O7
Data
O0 to O7
A0 to A14
Address
A0 to A14
VPP
HD407A4639R
VCC
OSC1
D2
D3
RA1
VT ref
VCref
X1
OE
OE
CE
CE
GND
Figure 93 PROM Mode Connections
111
HD404639R Series
Addressing Modes
RAM Addressing Modes
The MCU has three RAM addressing modes, as shown in figure 94 and described below.
Register Indirect Addressing Mode: The contents of the W, X, and Y registers (10 bits in total) are used
as a RAM address. When the area from $090 to $25F is used, a bank must be selected by the bank register
(V: $03F).
Direct Addressing Mode: A direct addressing instruction consists of two words. The first word contains
the opcode, and the contents of the second word (10 bits) are used as a RAM address.
Memory Register Addressing Mode: The memory registers (MR), which are located in 16 addresses
from $040 to $04F, are accessed with the LAMR and XMRA instructions.
W register
W1 W0
RAM address
X register
X3
X2
X1
Y register
X0
Y3
Y2
Y1
Y0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Register Direct Addressing
1st word of Instruction
Opcode
2nd word of Instruction
d
RAM address
9
d8
d7
d6
d5
d4
d3
d2
d1
d0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Direct Addressing
Instruction
Opcode
0
RAM address
0
0
1
0
m1
m0
0
AP9 AP8 AP7 AP6 AP5 AP4 AP3 AP2 AP1 AP0
Memory Register Addressing
Figure 94 RAM Addressing Modes
112
m3 m2
HD404639R Series
ROM Addressing Modes and the P Instruction
The MCU has four ROM addressing modes, as shown in figure 95 and described below.
Direct Addressing Mode: A program can branch to any address in the ROM memory space by executing
the JMPL, BRL, or CALL instruction. Each of these instructions replaces the 14 program counter bits
(PC 13–PC0) with 14-bit immediate data.
Current Page Addressing Mode: The MCU has 64 pages of ROM with 256 words per page. A program
can branch to any address in the current page by executing the BR instruction. This instruction replaces the
eight low-order bits of the program counter (PC7–PC0) with eight-bit immediate data. If the BR instruction
is on a page boundary (address 256n + 255), executing that instruction transfers the PC contents to the next
physical page, as shown in figure 97. This means that the execution of the BR instruction on a page
boundary will make the program branch to the next page.
Note that the HMCS400-series cross macroassembler has an automatic paging feature for ROM pages.
Zero-Page Addressing Mode: A program can branch to the zero-page subroutine area located at $0000–
$003F by executing the CAL instruction. When the CAL instruction is executed, 6 bits of immediate data
are placed in the six low-order bits of the program counter (PC 5–PC0), and 0s are placed in the eight highorder bits (PC13–PC6).
Table Data Addressing Mode: A program can branch to an address determined by the contents of fourbit immediate data, the accumulator, and the B register by executing the TBR instruction.
P Instruction: ROM data addressed in table data addressing mode can be referenced with the P instruction
as shown in figure 96. If bit 8 of the ROM data is 1, eight bits of ROM data are written to the accumulator
and the B register. If bit 9 is 1, eight bits of ROM data are written to the R1 and R2 port output registers.
If both bits 8 and 9 are 1, ROM data is written to the accumulator and the B register, and also to the R1 and
R2 port output registers at the same time.
The P instruction has no effect on the program counter.
113
HD404639R Series
1st word of instruction
[JMPL]
[BRL]
[CALL]
Opcode
p3
Program counter
2nd word of instruction
p2
p1
p0
d9
d8
d7
d6
d5
d4
d3
d2
d1
d0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Direct Addressing
Instruction
[BR]
Program counter
Opcode
b7
b6
b5
b4
b3
b2
b1
b0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Current Page Addressing
Instruction
[CAL]
0
Program counter
0
0
0
d5
Opcode
0
0
0
d4
d3
d2
d1
d0
0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Zero Page Addressing
Instruction
[TBR]
Opcode
p3
p2
p1
p0
B register
B3
0
Program counter
B0
A3
A2
A1
A0
0
PC13 PC12 PC11 PC10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0
Table Data Addressing
Figure 95 ROM Addressing Modes
114
B2 B1
Accumulator
HD404639R Series
Instruction
[P]
Opcode
p3
p2
p1
p0
B register
B3
0
Accumulator
B2 B1
B0
A3
A2
A1
A0
0
Referenced ROM address RA13 RA12 RA11 RA10 RA 9 RA 8 RA 7 RA 6 RA 5 RA 4 RA 3 RA 2 RA 1 RA 0
Address Designation
ROM data
RO9 RO8 RO7 RO6 RO5 RO4 RO3 RO2 RO1 RO0
Accumulator, B register
ROM data
B3
B2
B1
B0
A3 A
2
A1
A
0
If RO 8 = 1
RO9 RO8 RO7 RO6 RO5 RO4 RO3 RO2 RO1 RO0
Output registers R1, R2
B3
B2
B1
B0
B3
B2
B1
B0
If RO 9 = 1
Pattern Output
Figure 96 P Instruction
115
HD404639R Series
256 (n – 1) + 255
BR
AAA
256n
AAA
BBB
256n + 254
256n + 255
256 (n + 1)
NOP
BR
BR
BBB
AAA
NOP
Figure 97 Branching when the Branch Destination is on a Page Boundary
116
HD404639R Series
Absolute Maximum Ratings
Item
Symbol
Value
Unit
Supply voltage
VCC
–0.3 to +7.0
V
Programming voltage
VPP
–0.3 to +14.0
V
Pin voltage
VT
–0.3 to VCC + 0.3
V
Total permissible input current
∑Io
105
mA
2
Total permissible output current
–∑Io
50
mA
3
Maximum input current
Io
4
mA
4, 5
30
mA
4, 6
4
mA
7, 8
20
mA
7, 9
Maximum output current
–I o
Operating temperature
Topr
–20 to +75
°C
Storage temperature
Tstg
–55 to +125
°C
Note
1
Notes: Permanent damage may occur if these absolute maximum ratings are exceeded. Normal operation
must be under the conditions stated in the electrical characteristics tables. If these conditions are
exceeded, the LSI may malfunction or its reliability may be affected.
1. Applies to D 13 (VPP) of HD407A4639R.
2. The total permissible input current is the total of input currents simultaneously flowing in from all
the I/O pins to GND.
3. The total permissible output current is the total of output currents simultaneously flowing out from
VCC to all I/O pins.
4. The maximum input current is the maximum current flowing from each I/O pin to GND.
5. Applies to D 0–D 3, and R0–RC.
6. Applies to D 4–D 11 .
7. The maximum output current is the maximum current flowing out from V CC to each I/O pin.
8. Applies to D 4–D 11 and R0–RC.
9. Applies to D 0–D 3.
117
HD404639R Series
Electrical Characteristics
DC Characteristics (HD404638R, HD404639R, HD40A4638R, HD40A4639R: V CC = 2.7 to 6.0 V,
GND = 0 V, Ta = –20 to +75°C; HD407A4639R: V CC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C,
unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Input high
voltage
VIH
RESET, STOPC,
INT0 –INT4,SCK 1
SI 1, SCK 2, SI 2,
EVNB, EVND
0.9V CC
—
VCC + 0.3
V
OSC 1
VCC – 0.3
—
VCC + 0.3
V
RESET, STOPC,
INT0 –INT4, SCK 1
SI 1, SCK 2, SI 2,
EVNB, EVND
–0.3
—
0.10 VCC
V
OSC 1
–0.3
—
0.3
V
External clock
Output high VOH
voltage
SCK 1, SO1,
SCK 2, SO2,
TOB, TOC, TOD
VCC – 1.0
—
—
V
–I OH = 0.5 mA
Output low VOL
voltage
SCK 1, SO1,
SCK 2, SO2,
TOB, TOC, TOD
—
—
0.4
V
I OL = 0.4 mA
I/O leakage | IIL |
current
RESET, STOPC,
INT0 –INT4, SCK 1,
SI 1, SCK 2, SI 2,
SO1, SO2, EVNB,
EVND, OSC 1,
TOB, TOC, TOD
—
—
1
µA
Vin = 0 V to VCC
I CC1
Current
dissipation
in active
mode
VCC
—
2.5
5
mA
VCC = 5 V,
2
f OSC = 4 MHz,
digital input mode
I CC2
VCC
—
0.3
1.0
mA
VCC = 3 V,
2
f OSC = 800 kHz,
digital input mode
I CC3
VCC
—
5
9
mA
VCC = 5 V,
2, 8
f OSC = 8 MHz,
digital input mode
I CMP1
VCC
—
6.5
9
mA
VCC = 5 V,
f OSC = 4 MHz,
analog comp.
mode
Input low
voltage
118
VIL
Test Condition
Notes
External clock
1
3
HD404639R Series
Item
Pin(s)
Min
Typ
Max
Unit
Test Condition
Notes
I CMP2
Current
dissipation
in active
mode
VCC
—
2.8
3.5
mA
VCC = 3 V,
f OSC = 800 kHz,
analog comp.
mode
3
I CMP3
VCC
—
9
13
mA
VCC = 5 V,
f OSC = 8 MHz,
analog comp.
mode
3, 8
I SBY1
Current
dissipation
in standby
mode
VCC
—
1.0
2
mA
VCC = 5 V,
f OSC = 4 MHz
4
I SBY2
VCC
—
0.1
0.3
mA
VCC = 3 V,
f OSC = 800 kHz
4
I SBY3
VCC
—
2.0
4.0
mA
VCC = 5 V,
f OSC = 8 MHz
4, 8
I SUB
Current
dissipation
in subactive
mode
VCC
—
18
35
µA
VCC = 3 V,
32 kHz oscillator
5
I WTC
Current
dissipation
in watch
mode
VCC
—
4
7.5
µA
VCC = 3 V,
32 kHz oscillator
5
I STOP
Current
dissipation
in stop
mode
VCC
—
0.5
5
µA
VCC = 3 V,
no 32 kHz
oscillator
5
Stop mode VSTOP
retaining
voltage
VCC
2
—
—
V
No 32 kHz
oscillator
6
Comparator VC ref
input
reference
voltage
scope
VC ref
0
—
VCC – 1.2
V
–100
—
100
mV
VOFS = reference
voltage – VC ref
7
Allowable
error of
internal
reference
voltage
Symbol
VOFS
Notes: 1. Output buffer current is excluded.
2. I CC1, I CC2 and I CC3 are the source currents when no I/O current is flowing while the MCU is in reset
state.
Test conditions: MCU: Reset
Pins: RESET at V CC (VCC –0.3 to VCC)
TEST at V CC (VCC –0.3 to VCC)
119
HD404639R Series
3. RD0–RD3 pins are in analog input mode when no I/O current is flowing.
Test conditions: MCU: DTMF does not operate
Pins: RD0/COMP0 at GND (0 V to 0.3 V)
RD1/COMP1 at GND (0 V to 0.3 V)
RD2/COMP2 at GND (0 V to 0.3 V)
RD3/COMP3 at GND (0 V to 0.3 V)
RE 0/VCref at GND (0 V to 0.3 V)
4. I SBY1, I SBY2 and I SBY3 are the source currents when no I/O current is flowing while the MCU timer is
operating.
Test conditions: MCU: I/O reset
Serial interface stopped
DTMF does not operate
Standby mode
Pins: RESET at GND (0 V to 0.3 V)
TEST at V CC (VCC –0.3 to VCC)
5. These are the source currents when no I/O current is flowing.
Test conditions: Pins: RESET at GND (0 V to 0.3 V)
TEST at V CC (VCC –0.3 to VCC)
D13* at VCC (VCC –0.3 to VCC) * Applies to HD407A4639R.
6. RAM data retention.
7. The reference voltage is the expected internal VC ref voltage selected by the compare control
register (CCR: $016).
Example: when CCR = $2, reference voltage is 4/22 x VCC.
8. Applies to HD40A4638R, HD40A4639R, HD407A4639R.
120
HD404639R Series
I/O Characteristics for Standard Pins (HD404638R, HD404639R, HD40A4638R, HD40A4639R: V CC
= 2.7 to 6.0 V, GND = 0 V, Ta = –20 to +75°C; HD407A4639R: VCC = 2.7 to 5.5 V, GND = 0 V, T a = –
20 to +75°C, unless otherwise specified)
Item
Symbol
Pin(s)
Input high
voltage
VIH
Input low
voltage
Min
Typ
Max
Unit
Test Condition
D12–D 13 ,
0.7 VCC
R0–RD, RE0
—
VCC + 0.3
V
VIL
D12–D 13 ,
–0.3
R0–RD, RE0
—
0.3V CC
V
Output high
voltage
VOH
R0–RC
VCC –1.0 —
—
V
–I OH = 0.5 mA
Output low
voltage
VOL
R0–RC
—
—
0.4
V
I OL = 0.4 mA
I/O leakage
current
|I IL|
D12, R0–RD
RE 0,
—
—
1
µA
Vin = 0 V to VCC
1
D13
—
—
1
µA
Vin = 0 V to VCC
1, 2
—
—
1
µA
Vin = VCC – 0.3 V to VCC 1, 3
—
—
20
µA
Vin = 0 V to 0.3 V
5
30
90
µA
VCC = 3 V,
Pull-up MOS –I PU
current
R0–RC
Input high
voltage
VIHA
COMP0–
COMP3
VC ref+0.1 —
—
V
Analog compare mode
Input low
voltage
VILA
COMP0–
COMP3
—
VC ref –0.1
V
Analog compare mode
Notes
1, 3
Vin = 0 V
—
Notes: 1. Output buffer current is excluded.
2. Applies to HD404638R, HD404639R, HD40A4638R and HD40A4639R.
3. Apples to HD407A4639R.
121
HD404639R Series
I/O Characteristics for High-Current Pins (HD404638R, HD404639R, HD40A4638R, HD40A4639R:
VCC = 2.7 to 6.0 V, GND = 0 V, Ta = –20 to +75°C; HD407A4639R: V CC = 2.7 to 5.5 V, GND = 0 V, T a
= –20 to +75°C, unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Input high
voltage
VIH
D0–D 11
0.7 VCC
—
VCC + 0.3
V
Input low
voltage
VIL
D0–D 11
–0.3
—
0.3 VCC
V
Output high
voltage
VOH
D0–D 11
VCC – 1.0 —
—
V
–I OH = 0.5 mA,
D0–D 3
2.0
—
—
V
–I OH = 10 mA,
VCC = 4.5 V to 6.0 V
D0–D 11
—
—
0.4
V
I OL = 0.4 mA
D4–D 11
—
—
2.0
V
I OL = 15 mA,
VCC = 4.5 V to 6.0 V
1
D0–D 11
—
—
1
µA
Vin = 0 V to VCC
2
Pull-up MOS –I PU
current
D4–D 11
5
30
90
µA
VCC = 3 V, Vin = 0 V
Pull-down
I PD
MOS current
D0–D 3
5
30
90
µA
VCC = 3 V, Vin = 3 V
Output low
voltage
I/O leakage
current
VOL
|I IL|
Notes: 1. HD407A4639R; V CC = 4.5 V to 5.5 V
2. Output buffer current is excluded.
122
Test Condition
Notes
1
HD404639R Series
DTMF Characteristics (HD404638R, HD404639R, HD40A4638R, HD40A4639R: VCC = 2.7 to 6.0 V,
GND = 0 V, Ta = –20 to +75°C; HD407A4639R: V CC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C,
unless otherwise specified)
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Notes
Tone output
voltage (1)
VOR
TONER
500
660
—
mVrms VT ref – GND = 2.0 V,
RL = 100 kΩ
1
Tone output
voltage (2)
VOC
TONEC
520
690
—
mVrms VT ref – GND = 2.0 V,
RL = 100 kΩ
1
Tone output
distortion
%DIS
—
3
7
%
Short circuit between
TONER and TONEC
RL = 100 kΩ
2
Tone output
ratio
dBCR
—
2.5
—
dB
Short circuit between
TONER and TONEC
RL = 100 kΩ
2
Notes: 400 kHz, 800 kHz, 2 MHz, 3.58 MHz, 4MHz, 7.16 MHz, or 8 MHz can be used as the operating
trequency (f OSC).
1. See figure 98.
2. See figure 99.
123
HD404639R Series
AC Characteristics (HD404638R, HD404639R, HD40A4638R, HD40A4639R: V CC = 2.7 to 6.0 V,
GND = 0 V, Ta = –20 to +75°C; HD407A4639R: V CC = 2.7 to 5.5 V, GND = 0 V, Ta = –20 to +75°C,
unless otherwise specified)
Item
Symbol
Clock oscillation f OSC
frequency
Pin(s)
Min
Typ
Max
Unit
OSC 1,
OSC 2
—
400
—
kHz
1
—
800
—
kHz
1
—
2
—
MHz
1
—
3.58
—
MHz
1
—
4
—
MHz
1
—
7.16
—
MHz
1, 12
—
8
—
MHz
1, 12
—
32.768
—
kHz
—
8
—
µs
f OSC = 4 MHz,
1/32 division
2
—
4
—
µs
f OSC = 4 MHz,
1/16 division
2
—
2
—
µs
f OSC = 4 MHz,
1/8 division
2
—
1
—
µs
f OSC = 4 MHz,
1/4 division
2
—
244.14
—
µs
32 kHz oscillator,
1/8 division
3
—
122.07
—
µs
32 kHz oscillator,
1/4 division
3
X1, X2
Instruction cycle t cyc
time
t subcyc
Test Condition
Notes
Oscillation
t RC
stabilization time
(ceramic)
OSC 1,
OSC 2
—
—
7.5
ms
Oscillation
t RC
stabilization time
(crystal)
OSC 1,
OSC 2
—
—
40
ms
—
—
60
ms
X1, X2
—
—
3
s
Ta = –10°C to +60°C
4
OSC 1
1100
—
—
ns
f OSC = 400 kHz
7
550
—
—
ns
f OSC = 800 kHz
7
215
—
—
ns
f OSC = 2 MHz
7
115
—
—
ns
f OSC = 3.58 MHz
7
105
—
—
ns
f OSC = 4 MHz
7
57.5
—
—
ns
f OSC = 7.16 MHz
7, 12
52.5
—
—
ns
f OSC = 8 MHz
7, 12
External clock
high width
124
t CPH
4, 5
VCC = 3.5 V to 6.0 V
4, 5, 6
4, 5
HD404639R Series
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Notes
External clock
low width
t CPL
OSC 1
1100
—
—
ns
f OSC = 400 kHz
7
550
—
—
ns
f OSC = 800 kHz
7
215
—
—
ns
f OSC = 2 MHz
7
115
—
—
ns
f OSC = 3.58 MHz
7
105
—
—
ns
f OSC = 4 MHz
7
57.5
—
—
ns
f OSC = 7.16 MHz
7, 12
52.5
—
—
ns
f OSC = 8 MHz
7, 12
—
—
150
ns
f OSC = 400 kHz
7
—
—
75
ns
f OSC = 800 kHz
7
—
—
35
ns
f OSC = 2 MHz
7
—
—
25
ns
f OSC = 3.58 MHz
7
—
—
20
ns
f OSC = 4 MHz
7
—
—
12.5
ns
f OSC = 7.16 MHz
7, 12
—
—
10
ns
f OSC = 8 MHz
7, 12
—
—
150
ns
f OSC = 400 kHz
7
—
—
75
ns
f OSC = 800 kHz
7
—
—
35
ns
f OSC = 2 MHz
7
—
—
25
ns
f OSC = 3.58 MHz
7
—
—
20
ns
f OSC = 4 MHz
7
—
—
12.5
ns
f OSC = 7.16 MHz
7, 12
—
—
10
ns
f OSC = 8 MHz
7, 12
External clock
rise time
External clock
fall time
t CPr
t CPf
OSC 1
OSC 1
INT0–INT4,
EVNB, EVND
high width
t IH
INT0–
INT4,
EVNB,
EVND
2
—
—
t cyc /
t subcyc
8
INT0–INT4,
EVNB, EVND
low width
t IL
INT0–
INT4,
EVNB,
EVND
2
—
—
t cyc /
t subcyc
8
RESET high
width
t RSTH
RESET
2
—
—
t cyc
9
STOPC low
width
t STPL
STOPC
1
—
—
t RC
10
RESET fall time
t RSTf
RESET
—
—
20
ms
9
STOPC rise time t STPr
STOPC
—
—
20
ms
10
125
HD404639R Series
Item
Symbol
Pin(s)
Min
Typ
Max
Unit
Test Condition
Input
capacitance
Cin
All pins
except
D13
—
—
15
pF
f = 1 MHz, Vin = 0 V
D13
—
—
15
pF
f = 1 MHz, Vin = 0 V
13
D13
—
—
180
pF
f = 1 MHz, Vin = 0 V
14
COMP0– —
COMP3
—
2
t cyc
Analog
t CSTB
comparator
stabilization time
Notes
11
Notes: Except for the HD407A4639R, when V CC is between 2.2 V and 6.0 V, watch mode can be supported,
and instruction execution is possible in active mode.
1. Bits 0 and 1 (SSR10, SSR11) of system clock select register 1 (SSR1: $029) and bits 2 and 3
(SSR22, SSR23) of system clock select register 2 (SSR2: $02A) must be set according to the
system clock frequency.
2. Bits 0 and 1 (SSR20, SSR21) of system clock select register 2 (SSR2: $02A) must be set
according to the division ratio of the system clock frequency.
3. Bit 2 (SSR12) of system clock select register 1 (SSR1: $029) must be set according to the
division ratio of the subsystem clock frequency.
4. The oscillation stabilization time is the period required for the oscillator to stabilize after V CC
reaches 2.7 V at power-on, or after RESET input goes high or STOPC input goes low when stop
mode is cancelled. At power-on or when stop mode is cancelled, RESET or STOPC must be
input for at least tRC to ensure the oscillation stabilization time. If using a ceramic oscillator,
contact its manufacturer to determine what stabilization time is required, since it will depend on
the circuit constants and stray capacitance. Set bits 0 and 1 (MIS0, MIS1) of the miscellaneous
register (MIS: $00C) according to the system oscillation of the oscillation stabilization time.
5. Bits 0 and 1 (MIS0, MIS1) of the miscellaneous register (MIS: $00C) must be set according to
the oscillation stabilization time of the system clock oscillator.
6. HD407A4639R: V CC = 3.5 V to 5.5 V.
7. Refer to figure 100.
8. Refer to figure 101. The t cyc unit applies when the MCU is in standby or active mode. The tsubcyc
unit applies when the MCU is in watch or subactive mode.
9. Refer to figure 102.
10. Refer to figure 103.
11. Analog comparator stabilization time is the period for the analog comparator to stabilize and for
correct data to be read after entering RD 0/COMP0–RD3/COMP3 into analog input mode.
12. Applies to HD40A4638R, HD40A4639R and HD407A4639R.
HD40A4638R, HD40A4639R: VCC = 4.5 V to 6.0 V
HD407A4639R: V CC = 4.5 V to 5.5 V
13. Applies to HD404638R, HD404639R, HD40A4638R and HD40A4639R.
14. Applies to HD407A4639R.
126
HD404639R Series
Serial Interface Timing Characteristics (HD404638R, HD404639R, HD40A4638R, HD40A4639R:
VCC = 2.7 to 6.0 V, GND = 0 V, Ta = –20 to +75°C; HD407A4639R: VCC = 2.7 to 5.5 V, GND = 0 V, Ta
= –20 to +75°C, unless otherwise specified)
During Transmit Clock Output
Item
Symbol
Pin(s)
Test Condition
Min
Typ
Max
Unit
Notes
Transmit
clock cycle
time
t Scyc
SCK 1, SCK 2
Load shown in figure 105
1
—
—
t cyc
1
Transmit
clock high
width
t SCKH
SCK 1, SCK 2
Load shown in figure 105
0.5
—
—
t Scyc
1
Transmit
clock low
width
t SCKL
SCK 1, SCK 2
Load shown in figure 105
0.5
—
—
t Scyc
1
Transmit
clock rise
time
t SCKr
SCK 1, SCK 2
Load shown in figure 105
—
—
200
ns
1
Transmit
t SCKf
clock fall time
SCK 1, SCK 2
Load shown in figure 105
—
—
200
ns
1
Serial output t DSO
data delay
time
SO1, SO 2
Load shown in figure 105
—
—
500
ns
1
Serial input
data setup
time
t SSI
SI 1, SI2
300
—
—
ns
1
Serial input
data hold
time
t HSI
SI 1, SI2
300
—
—
ns
1
127
HD404639R Series
During Transmit Clock Input
Item
Symbol
Pin(s)
Transmit
clock cycle
time
t Scyc
Transmit
clock high
width
Min
Typ
Max
Unit
Notes
SCK 1, SCK 2
1
—
—
t cyc
1
t SCKH
SCK 1, SCK 2
0.5
—
—
t Scyc
1
Transmit
clock low
width
t SCKL
SCK 1, SCK 2
0.5
—
—
t Scyc
1
Transmit
clock rise
time
t SCKr
SCK 1, SCK 2
—
—
200
ns
1
Transmit
t SCKf
clock fall time
SCK 1, SCK 2
—
—
200
ns
1
Serial output t DSO
data delay
time
SO1, SO 2
—
—
500
ns
1
Serial input
data setup
time
t SSI
SI 1, SI2
300
—
—
ns
1
Serial input
data hold
time
t HSI
SI 1, SI2
300
—
—
ns
1
Note:
Test Condition
Load shown in figure 105
1. Refer to figure 104.
RL = 100 kΩ
TONEC
RL = 100 kΩ
TONER
GND
Figure 98 TONE Output Load Circuit
128
HD404639R Series
TONEC
RL = 100 kΩ
TONER
GND
Figure 99 Distortion dBCR Load Circuit
OSC 1
1/fCP
VCC – 0.3 V
0.3 V
tCPL
tCPH
tCPr
tCPf
Figure 100 External Clock Timing
INT0 –INT4, EVNB, EVND
0.9 VCC
0.1 VCC
t IL
t IH
Figure 101 Interrupt Timing
RESET
0.9 VCC
0.1 VCC
tRSTH
tRSTf
Figure 102 Reset Timing
129
HD404639R Series
STOPC
0.9 VCC
tSTPL
0.1 V CC
tSTPr
Figure 103 STOPC Timing
t Scyc
t SCKf
SCK 1
SCK 2
V CC– 1.0 V (0.9 VCC )*
0.4 V (0.1 VCC )*
t SCKr
t SCKL
t SCKH
t DSO
VCC – 0.5 V
0.4 V
SO 1
SO 2
t HSI
t SSI
0.9 V CC
0.1 V CC
SI 1
SI 2
Note: * VCC – 1.0 V and 0.4 V are the threshold voltages for transmit clock output.
0.9 VCC and 0.1 VCC are the threshold voltages for transmit clock output.
Figure 104 Serial Interface Timing
VCC
RL = 2.6 kΩ
Test point
C
30 pF
R
12 kΩ
1S2074 H
or equivalent
Figure 105 Timing Load Circuit
130
HD404639R Series
Notes on ROM Out
Please pay attention to the following items regarding ROM out.
On ROM out, fill the ROM area indicated below with 1s to create the same data size as a 16-kword version
(HD404639R, HD40A4639R). A 16-kword data size is required to change ROM data to mask
manufacturing data since the program used is for a 16-kword version.
This limitation applies when using an EPROM or a data base.
ROM 8-kword version:
HD404638R, HD40A4638R
Address $2000–$3FFF
$0000
Vector address
(16 words)
$000F
$0010
Zero-page subroutine
(64 words)
$003F
$0040
Pattern & program
(8,192 words)
$1FFF
$2000
Not used
$3FFF
Fill this area with 1s
131
HD404639R Series
HD404638/HD404639/HD404638R/HD404639R/HD40A4638R/HD40A4639R Option List
Please check off the appropriate applications and
enter the necessary information.
Date of order
/
/
Customer
1. ROM Size
Department
Standaed version : HD404638
Standard version : HD404638R
ROM
8-kword
High-speed version : HD40A4638R
ROM code name
LSI number
Standard version : HD404639
Standard version : HD404639R
Name
ROM
16-kword
High-speed version : HD40A4639R
2. Optional Functions
*
With 32-kHz CPU operation, with time-base for clock
*
Without 32-kHz CPU operation, with time-base for clock
*
Without 32-kHz CPU operation, without time-base
Note: * Options marked with an asterisk require a subsystem crystal oscillator (X1, X2).
3. ROM Code Media
Please specify the first type listed below (the upper bits and lower bits are mixed together) when using
the EPROM on-package microcomputer type (including ZTATTM version).
EPROM: The upper bits and lower bits are mixed together. The upper five bits and lower five bits are
programmed to the same EPROM in alternating order (i.e., LULULU...).
EPROM: The upper bits and lower bits are separated. The upper bits and lower five bits are
programmed to different EPROMs.
4. Oscillator for OSC1 and OSC2
Ceramic oscillator
f=
MHz
Crystal oscillator
f=
MHz
External clock
f=
MHz
5. Stop Mode
Used
Not used
6. Package
FP-80B
132
HD404639R Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica
: http:semiconductor.hitachi.com/
Europe
: http://www.hitachi-eu.com/hel/ecg
Asia (Singapore)
: http://www.has.hitachi.com.sg/grp3/sicd/index.htm
Asia (Taiwan)
: http://www.hitachi.com.tw/E/Product/SICD_Frame.htm
Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm
Japan
: http://www.hitachi.co.jp/Sicd/indx.htm
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Hitachi Europe GmbH
Electronic components Group
Dornacher Straße 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 778322
Hitachi Asia Pte. Ltd.
16 Collyer Quay #20-00
Hitachi Tower
Singapore 049318
Tel: 535-2100
Fax: 535-1533
Hitachi Asia Ltd.
Taipei Branch Office
3F, Hung Kuo Building. No.167,
Tun-Hwa North Road, Taipei (105)
Tel: <886> (2) 2718-3666
Fax: <886> (2) 2718-8180
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower, World Finance Centre,
Harbour City, Canton Road, Tsim Sha Tsui,
Kowloon, Hong Kong
Tel: <852> (2) 735 9218
Fax: <852> (2) 730 0281
Telex: 40815 HITEC HX
Copyright © Hitachi, Ltd., 1998. All rights reserved. Printed in Japan.
133