NJG1560PB1 Feb.28,2002 Ver.0 PDC Dual Band MIXER GaAs MMIC QGENERAL DESCRIPTION The NJG1560PB1 is a mixer GaAs MMIC includes local amplifier targeted to dual band (800MHz, 1.5GHz) application. The band switching between 800MHz and 1500MHz is made by 1bit control signal by using inverter circuit included in this IC. The ultra small and thin FFP12-B1 is applied. QFEATURES OLow voltage operation OLow current consumption OLow Inverter current OHigh conversion gain QPACKAGE OUTLINE NJG1560PB1 +2.8V typ. 5.9mA typ. 100uA typ. 11dB typ. @VCTL=0V, fRF1=820MHz 11dB typ. @VCTL=2.4V, fRF2=1489MHz @VCTL=0V, fRF1=820MHz +3dBm typ. +3dBm typ. @VCTL=2.4V, fRF2=1489MHz @VCTL=0V, fRF1=820MHz 5.5dB typ. 5.0dB typ. @VCTL=2.4V, fRF2=1489MHz FFP12-B1 (Package size: 2.0mmx2.0mmx0.85mm) OHigh input IP3 OLow noise figure OUltra small & thin package QPIN CONFIGURATION (Top View) 9 8 7 10 6 11 5 12 4 1 2 3 Pin Connection 1. GND 2. LOIN1 (800MHz) 3. VCTL 4. IFOUT 5. VLO1 (800MHz) 6. VLO2 (1.5GHz) 7. VINV 8. GND 9. LOIN2 (1.5GHz) 10. GND 11. RFIN2 (1.5GHz) 12. RFIN1 (800MHz) Note: The specifications and description listed in this catalog are subject to change without prior notice. -1- NJG1560PB1 QABSOLUTE MAXIMUM RATINGS (Ta=25°C, Zs=Zl=50Ω) PARAMETERS SYMBOL CONDITIONS RATINGS UNITS Operating voltage VDD IFOUT, VLO 1, VLO2, VINV ports 5.0 V Control voltage VCTL VCTL port VINV V RFIN1, RFIN2, LOIN1, LOIN2 ports +10 dBm Input power Pin Power dissipation PD 300 mW Operating temperature Topr -40~+85 °C Storage temperature Tstg -55~+125 °C QELECTRICAL CHARACTERISTICS 1 (DC) GENERAL CONDITIONS: Ta=25°C, VMIX=VLO1=VLO2=VINV=2.8V PARAMETERS Mixer supply voltage SYMBOL CONDITIONS MIN TYP MAX UNITS VMIX IFOUT port 2.5 2.8 4.5 V VLO1 VLO1 ports 2.5 2.8 4.5 V VLO2 VLO2 ports 2.5 2.8 4.5 V Inverter supply voltage VINV VINV port 2.5 2.8 4.5 V Mixer current IMIX IFOUT port, PRF=PLO=OFF, VCTL=0V or 2.4V - 4.9 6.1 mA Local Amplifier current1 ILO1 VLO1 port, PRF=PLO=OFF, VCTL=0V - 1.0 1.2 mA Local Amplifier current2 ILO2 VLO2port, PRF=PLO=OFF, VCTL=2.4V - 1.0 1.2 mA Inverter current IINV VINV port - 100 150 uA Control voltage (LOW) VCTL(L) VCTL port 0 0 0.8 V Control voltage (HIGH) VCTL(H) VCTL port 2.0 2.4 VINV V - 20 40 uA Local Amplifier supply voltage 1 Local Amplifier supply voltage 2 Control -2- current ICTL VCTL port, VCTL=2.4V NJG1560PB1 QELECTRICAL CHARACTERISTICS 2 (800MHz RF) GENERAL CONDITIONS: Ta=+25°C, VMIX=VLO1=VINV=2.8V, VCTL=0V, fRF1=820MHz, PRF1=-30dBm, fLO1=689.95MHz, PLO1=-15dBm, fIF=130.05MHz, Zs=Zl=50Ω, with application circuit PARAMETERS SYMBOL CONDITIONS RFIN1 port MIN TYP MAX UNITS 810 820 885 MHz 10.0 11.0 12.0 dB Operating frequency freq Conversion gain Gc Noise figure NF SSB NF - 5.5 6.5 dB Input 3rd order intercept point IIP3 2 tone offset frequency=100kHz 0 +3.0 - dBm dBm Pout at 1dB gain compression point P-1dB(IN) -11.0 -9.0 - RF IN1 port VSWR VSWRRF - 1.5 2.0 LOCAL IN1 port VSWR VSWRLO - 1.5 2.0 IF OUT port VSWR VSWRIF - 1.5 2.0 QELECTRICAL CHARACTERISTICS 3 (1.5GHz RF) GENERAL CONDITIONS: Ta=+25°C, VMIX=VLO2=VINV=2.8V, VCTL=2.4V, fRF2=1489MHz, PRF2=-30dBm, fLO2=1358.95MHz, PLO2=-15dBm, fIF=130.05MHz, Zs=Zl=50Ω, with application circuit PARAMETERS SYMBOL CONDITIONS RFIN2 port MIN TYP MAX UNITS 1477 1489 1501 MHz 10.0 11.0 12.0 dB Operating frequency freq Conversion gain Gc Noise figure NF SSB NF - 5.0 6.0 dB Input 3rd order intercept point IIP3 2 tone offset frequency=100kHz 0 +3.0 - dBm dBm Pout at 1dB gain compression point P-1dB(IN) -11.0 -9.0 - RF IN2 port VSWR VSWRRF - 1.5 2.0 LOCAL IN2 port VSWR VSWRLO - 1.5 2.0 IF OUT port VSWR VSWRIF 1.5 2.0 -3- NJG1560PB1 QTERMINAL INFORMATION Pin Symbol Description 1 GND 2 LOIN1 3 VCTL 4 IFOUT 5 VLO1 6 VLO2 1.5GHz band local amplifier supply terminal. Please place L5 close to this terminal as shown in test circuit. 7 VINV Power supply terminal of the inverter circuit. 8 GND Ground terminal(0V). 9 LOIN2 10 GND 11 RFIN2 RF input terminal of 1.5GHz band mixer. External matching circuit is required. 12 RFIN1 RF input terminal of 800MHz band mixer. External matching circuit is required. Ground terminal(0V). Local power input terminal of 800MHz band local amplifier. External matching circuit is required. Control voltage input terminal. This terminal is set to 800MHz band or 1.5GHz band to select. IF signal output terminal for mixer external matching circuit is required. Please connect mixer power supply through choke inductor (L7) as shown in test circuit. 800MHz band local amplifier supply terminal. Please place L6 close to this terminal as shown in test circuit. Local power input terminal of 1.5GHz local amplifier. External matching circuit is required. Ground terminal(0V). NOTE: 1) Ground terminal (1, 8, 10pin) should be connected to ground plane by multiple via holes for good grounding. -4- NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) Gc , NF vs. RF Frequency 11 11 10 10 9 9 8 NF 7 7 6 6 5 5 800 820 840 860 880 10 10 8 8 6 6 4 2 -40 4 900 2 -30 7 6 13 5 12 4 3 11 IIP3 880 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V 10 OIP3 8 12 6 10 4 8 2 IIP3 2 1 9 14 OIP3 (dBm) 14 860 10 16 IIP3 (dBm) OIP3 (dBm) OIP3 840 0 OIP3, IIP3 vs. LO Power 8 16 820 -10 Condition fIF=130.05MHz fRF=820MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V OIP3 , IIP3 vs. RF Frequency 8 800 -20 LO Power (dBm) Condition fIF=130.05MHz fRF=800~900MHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V 10 4 NF RF Frequency (MHz) 15 12 0 900 6 4 -40 0 -2 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V -5- IIP3 (dBm) 8 Gc 12 Conversion Gain (dB) Gc Noise Figure (dB) Conversion Gain (dB) 12 14 14 12 Noise Figure (dB) 13 Gc, NF vs. LO Power NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) IF, IM3 vs. RF Power 5 20 0 0 -5 IF , IM3 (dBm) IF Output Power (dBm) IF Output Power vs. RF Power -10 -15 IF -20 -40 -60 -20 IM3 -80 -25 P-1dB(IN)=-7.8dBm -30 -40 -30 -20 -10 0 10 Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V -12 LOCAL Leak Level (dBm) Plk-IF -16 -18 -20 -22 Plk-RF -24 -26 680 700 720 740 LO Frequency (MHz) -6- -20 -10 0 Condition fIF=130.05MHz fRF=820.0+820.1MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V LOCAL Leak Level vs. LO Frequency -28 660 -30 RF Power (dBm) RF Power (dBm) -14 -100 -40 760 780 10 NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) OIP3, IIP3 vs. Ambient Temperature Gc, NF vs. Ambient Temperature 12 14 Gc 18 12 16 14 fRF=810MHz OIP3 fRF=820MHz 12 10 8 8 NF 6 6 4 4 fRF=810MHz 14 10 12 8 10 6 8 4 fRF=820MHz 2 0 -40 fRF=885MHz -20 0 20 40 60 2 6 0 4 -40 80 o IIP3 2 0 -20 0 20 40 60 80 o Ambient Temperature ( C) Ambient Temperature ( C) Condition fIF=130.05MHz fRF=810~885MHz, PRF=-30dBm fLO=679.95~754.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V Condition fIF=130.05MHz fRF1=810~885MHz, fRF2=fRF1+100kHz, PRF=-30dBm fLO==679.95~754.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V P-1dB(IN) vs. Ambient Temperature -4 P-1dB(IN) (dBm) -6 -8 -10 fRF=820MHz -12 -14 -16 -50 0 50 100 o Ambient Temperature ( C) Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V -7- IIP3 (dBm) 10 OIP3 (dBm) fRF=885MHz Noise Figure (dB) Conversion Gain (dB) 14 NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) Conversion Gain vs. Frequency Noise Figure vs. Frequency 10 8 12 Noise Figure (dB) Conversion Gain (dB) 14 10 8 o -40 C o -25 C o 0 C o 25 C 6 6 4 o -40 C o 2 -25 C o 0 C o 25 C o o 0 50 C 50 C o o 80 C 4 800 820 840 860 880 80 C -2 800 900 820 RF Frequency (MHz) OIP3 vs. Frequency 880 18 10 16 8 14 6 12 o -40 C o -25 C 4 2 o -40 C o 0C 8 o -25 C 0 o 25 C o 0 C o 50 C o 25 C o 6 900 IIP3 vs. Frequency IIP3 (dBm) OIP3 (dBm) 860 Condition fIF=130.05MHz fRF=800~900MHz fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V Condition fIF=130.05MHz fRF=800~900MHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V 10 840 RF Frequency (MHz) -2 80 C o 50 C o 80 C 4 800 820 840 860 880 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V -8- 900 -4 800 820 840 860 880 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V 900 NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) Noise Figure vs. LO Power Conversion Gain vs. LO Power 14 14 12 12 o o -25 C o Noise Figure (dB) Conversion Gain (dB) -40 C 10 8 o -40 C o -25 C o 0 C 6 o 25 C o 50 C o 80 C 4 2 -40 -30 -20 -10 0 0C o 25 C 10 o 50 C o 80 C 8 6 4 2 -40 10 -30 -20 -10 0 10 LO Power (dBm) LO Power (dBm) Condition fIF=130.05MHz fRF=820MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V IIP3 vs. LO Power OIP3 vs. LO Power 16 10 14 8 o -40 C o -25 C o 0C o 12 IIP3 (dBm) OIP3 (dBm) 25 C 10 o -40 C 8 o -25 C o 6 50 C o 80 C 4 2 o 0C o 25 C 6 0 o 50 C o 80 C 4 -40 -30 -20 -10 LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V 0 10 -2 -40 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V -9- NJG1560PB1 QTYPICAL CHARACTERISTICS (800MHz Band) RF IN1 Port Impedance (LOCAL IN1 Port, IF OUT Port: 50Ω term.) IF OUT Port Impedance (RF IN1 Port, LOCAL IN1 Port: 50Ω term.) - 10 - LOCAL IN1 Port Impedance (RF IN1 Port, IF OUT Port: 50Ω term.) NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) Gc , NF vs. RF Frequency 10 12 10 9 9 8 8 7 NF 7 6 6 5 18 Gc 10 14 8 12 6 10 4 8 2 6 0 -2 -40 5 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 2 -30 0 10 OIP3 , IIP3 vs. LO Power 14 18 16 12 16 OIP3 12 8 10 6 IIP3 4 2 4 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 (dBm) 10 14 OIP3 12 14 10 12 8 10 6 8 4 6 2 IIP3 4 2 -40 0 -2 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V - 11 - IIP3 (dBm) 18 IIP3 (dBm) OIP3 (dBm) -10 Condition fIF=130.05MHz fRF=1489MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 , IIP3 vs. RF Frequency 6 -20 LO Power (dBm) Condition fIF=130.05MHz fRF=1470~1510MHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V 8 4 NF RF Frequency (MHz) 14 16 Noise Figure (dB) Gc Conversion Gain (dB) Conversion Gain (dB) 11 11 Noise Figure (dB) 12 Gc , NF vs. LO Power 14 NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) IF Output Power vs. RF Power IF , IM3 vs. RF Power 5 20 IF Output Power (dBm) 0 0 IF IF , IM3 (dBm) -5 -10 -15 -20 -40 -60 -20 IM3 -80 -25 P-1dB(IN)=-8.2dBm -30 -40 -30 -20 -10 0 10 LOCAL Leak Level (dBm) 0 Condition fIF=130.05MHz fRF=1489.0+1489.1MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V Plk-RF Plk-IF -35 1345 1350 1355 1360 1365 1370 LO Frequency (MHz) - 12 - -10 Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V -25 -40 1340 -20 RF Power (dBm) LOCAL Leak Level vs. LO Frequency -30 -30 RF Power (dBm) -15 -20 -100 -40 1375 1380 10 NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) Gc, NF vs. Ambient Temperature 16 10 10 8 8 NF 6 6 4 4 fRF=1477MHz 12 10 14 8 12 IIP3 6 10 4 8 fRF=1477MHz fRF=1489MHz 2 OIP3 (dBm) 12 Noise Figure (dB) 12 OIP3 2 fRF=1489MHz 6 fRF=1501MHz 0 -40 0 -20 0 20 40 60 2 fRF=1501MHz 80 4 -40 0 -20 0 20 40 60 80 o o Ambient Temperature ( C) Ambient Temperature ( C) Condition fIF=130.05MHz fRF=1477~1501MHz, PRF=-30dBm fLO=1346.95~1470.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V Condition fIF=130.05MHz fRF1=1477~1501MHz, fRF2=fRF1+100kHz, PRF=-30dBm fLO=1346.95~1470.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V P-1dB(IN) vs. Ambient Temperature -4 P-1dB(IN) (dBm) -6 -8 -10 -12 fRF=1489MHz -14 -16 -40 -20 0 20 40 60 80 o Ambient Temperature ( C) Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V - 13 - IIP3 (dBm) Gc 14 18 14 14 Conversion Gain (dB) OIP3, IIP3 vs. Ambient Temperature NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) Conversion Gain vs. Frequency Noise Figure vs. Frequency 14 12 10 8 o -40 C o -25 C o 0 C Noise Figure (dB) Conversion Gain (dB) o 10 12 -40 C o -25 C o 0 C o 8 25 C o 50 C o 80 C 6 4 o 6 25 C 2 o 50 C o 80 C 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) RF Frequency (MHz) Condition fIF=130.05MHz fRF=1470~1510MHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V Condition fIF=130.05MHz fRF=1470~1510MHz fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 vs. Frequency IIP3 vs. Frequency 18 14 16 12 o -40 C o -25 C 12 o -40 C 10 o -25 C o 0 C o 25 C 8 o IIP3 (dBm) OIP3 (dBm) o 0 C 10 14 o 25 C o 50 C o 8 80 C 6 4 50 C o 80 C 6 2 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) RF Frequency (MHz) Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V - 14 - Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) Noise Figure vs. LO Power 14 18 12 16 o -40 C 10 Noise Figure (dB) Conversion Gain (dB) Conversion Gain vs. LO Power 8 6 o 4 -40 C o -25 C o 0 C 2 o 25 C o 14 -25 C o 0 C o 25 C 12 o 50 C o 80 C 10 8 6 o 50 C 0 -2 -40 4 o 80 C -30 -20 -10 0 2 -40 10 -30 LO Power (dBm) -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=1489MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 vs. LO Power IIP3 vs. LO Power 18 14 16 12 o -40 C o -25 C o 10 o 25 C o IIP3 (dBm) OIP3 (dBm) 14 0 C 12 10 o -40 C o -25 C 8 o 0 C 50 C 8 o 80 C 6 4 o 25 C 6 2 o 50 C o 80 C 4 2 -40 0 -30 -20 -10 0 LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V 10 -2 -40 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V - 15 - NJG1560PB1 QTYPICAL CHARACTERISTICS (1.5GHz Band) RF IN2 Port Impedance (LOCAL IN2 Port, IF OUT Port: 50Ω term.) IF OUT Port Impedance (RF IN2 Port, LOCAL IN2 Port: 50Ω term.) - 16 - LOCAL IN2 Port Impedance (RF IN2 Port, IF OUT Port: 50Ω term.) NJG1560PB1 QAPPLICATION CIRCUIT (Top View) LOCAL IN2 (1.5GHz) VINV=2.8V L4 15nH VLO=2.8V 9 8 7 L5 12nH L3 RF IN2 2.2nH (1.5GHz) L2 6.8nH L1 33nH RF IN1 (800MHz) 6 10 L6 39nH 11 5 12 R1 3.9kΩ C1 0.01uF C3 9pF 4 C2 18pF IF OUT L7 180nH 1 2 3 L8 47nH C4 0.01uF VMIX=2.8V LOCAL IN1 (800MHz) Parts list PARTS ID L1 L2 L3 L4 L5 L6 L7 L8 C1 C2 C3 C4 R1 VCTL=0 or 2.4V VCTL=0V :800MHz ON VCTL=2.4V :1.5GHz ON COMMENT TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1608, 1608size) TAIYO-YUDEN (HK1005, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) 1005 Size - 17 - NJG1560PB1 QRECOMMENDED PCB DESIGN (Top View) LOCAL IN2 (1.5GHz) VINV RF IN2 (1.5GHz) VLO L4 C1 L3 L5 L2 R1 L1 IF OUT L6 C3 L7 C2 L8 VMIX C4 RF IN1 (800MHz) VCTL LOCAL IN1 1pin INDEX PCB(FR-4), t=0.2mm MICROSTRIP LINE WIDTH=0.4mm (Zo=50Ω) PCB SIZE=33.6x26.6mm PRECAUTIONS 1. Please locate L6 close to VLO1 terminal (5). 2. Please locate L5 close to VLO2 terminal (6). 3. Please locate C1 close to L5 and L6. 4. Please locate C4 close to L7. - 18 - NJG1560PB1 QMEASURING BLOCK DIAGRAM LOCAL IN1 or 2 SG (LOCAL) LOCAL IN1 or 2 IF OUT Spectrum Analyzer D.U.T. PCB VMIX= VLO= VINV =2.8V VCTL= 0 or 2.4V VMIX= VLO= VINV =2.8V VCTL= 0 or 2.4V SG (LOCAL) D.U.T. PCB BPF RF IN1 or 2 IF OUT NF Meter RF IN1 or 2 BPF 6dB ATT SG (RF) Noise Source BPF Conversion Gain Measuring Block Diagram VCTL= 0 or 2.4V VMIX= VLO= VINV =2.8V LOCAL IN1 or 2 SG (LOCAL) Noise Figure Measuring Block Diagram IF OUT D.U.T. PCB Spectrum Analyzer RF IN1 or 2 SG (RF1) Power Comb. ATT SG (RF2) OIP3, IIP3 Measuring Block Diagram - 19 - NJG1560PB1 QPACKAGE OUTLINE (FFP12-B1) 12pin 1pin INDEX (TOP VIEW) 0.35 1pin 2pin INDEX 0.254±0.1 0.85±0.15 0. 2.0±0.1 0.30 0.17 0.20 0.50 0.103 0.303 35 (SIDE VIEW) (BOTTOM VIEW) 0.365 0.27 2.0±0.1 UNIT PCB OVER COAT TERMINAL TREAT WEIGHT Cautions on using this product This product contains Gallium-Arsenide (GaAs) which is a harmful material. • Do NOT eat or put into mouth. • Do NOT dispose in fire or break up this product. • Do NOT chemically make gas or powder with this product. • To waste this product, please obey the relating law of your country. This product may be damaged with electric static discharge (ESD) or spike voltage. Please handle with care to avoid these damages. - 20 - : mm : Ceramic : Epoxy resin : Au : 10mg [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.