PI74ALVCH16240 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Inverting 16-Bit Buffer Driver with 3-State Outputs Product Features Product Description • • • • Pericom Semiconductors PI74ALVCH series of logic circuits are produced in the Companys advanced 0.5 micron CMOS technology, achieving industry leading speed. • • • • PI74ALVCH16240 is designed for low voltage operation VCC = 2.3V to 3.6V Hysteresis on all inputs Typical VOLP (Output Ground Bounce) < 0.8V at VCC = 3.3V, TA = 25°C Typical VOHV (Output VOH Undershoot) < 2.0V at VCC = 3.3V, TA = 25°C Bus Hold retains last active bus state during 3-State, eliminating the need for external pullup resistors Industrial operation at 40°C to +85°C Packages available: 48-pin 240 mil wide plastic TSSOP (A) 48-pin 300 mil wide plastic SSOP (V) The PI74ALVCH16240 is an inverting 16-bit buffer/driver designed for low voltage 2.3V to 3.6V VCC operation. The buffer/driver is designed specifically to improve both the performance and density of 3-State memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The device can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. It provides inverting outputs and symmetrical active-low output-enable (OE) inputs. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor in which the minimum value is determined by the current-sinking capability of the driver. The PI74ALVCH16240 has Bus Hold which retains the data inputs last state whenever the data input goes to high-impedance preventing floating inputs and eliminating the need for pullup/ down resistors. Logic Block Diagram 1 PS8086B 10/07/98 PI74ALVCH16240 Inverting 16-Bit Buffer Driver with 3-State Outputs 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Product Pin Description Pin Name OE Ax Yx GND VCC Truth Table(1) Description 3-State Output Enable Inputs (Active LOW) Inputs 3-State Outputs Ground Power Inputs Outputs OE AX YX L H L L L H H X Z Notes: 1. H = High Signal Level L = Low Signal Level X = Don't Care or Irrelevant Z = High Impedance Product Pin Configuration 2 PS8086B 10/07/98 PI74ALVCH16240 Inverting 16-Bit Buffer Driver with 3-State Outputs 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ............................................................ 65°C to +150°C Ambient Temperature with Power Applied .......................... 40°C to +85°C Input Voltage Range, VIN .................................................... 0.5V to VCC +0.5V Output Voltage Range, VOUT ............................................. 0.5V to VCC +0.5V DC Input Voltage ................................................................... 0.5V to +5.0V DC Output Current .............................................................................. 100 mA Power Dissipation ................................................................................... 1.0W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 3.3V ±10%) Te s t Conditions (1) D e s cription VCC Supply Voltage VIH(3) Input HIGH Voltage VIL(3) Input LO W Voltage VIN(3) Input Voltage 0 VCC VOUT(3) O utput Voltage 0 VCC VOH VOL IOH(3) IOL(3) O utput HIGH Voltage O utput LO W Voltage O utput HIGH Current O utput LO W Current M in. Typ.(2) Parame te rs 2.3 VCC = 2.3V to 2.7V 1.7 VCC = 2.7V to 3.6V 2.0 M ax. 3.6 VCC = 2.3V to 2.7V 0.7 VCC = 2.7V to 3.6V 0.8 IOH = - 100mA, VCC = Min. to Max. VCC - 0.2 VIH = 1.7V, IOH = - 6mA, VCC = 2.3V 2.0 VIH = 1.7V, IOH = - 12mA, VCC = 2.3V 1.7 VIH = 2.0V, IOH = - 12mA, VCC = 2.7V 2.2 VIH = 2.0V, IOH = - 12mA, VCC = 3.0V 2.4 VIH = 2.0V, IOH = - 24mA, VCC = 3.0V 2.0 V IOL = 100mA, VIL = Min. to Max. 0.2 VIL = 0.7V, IOL = 6mA, VCC = 2.3V 0.4 VIL = 0.7V, IOL = 12mA, VCC = 2.3V 0.7 VIL = 0.8V, IOL = 12mA, VCC = 2.7V 0.4 VIL = 0.8V, IOL = 24mA, VCC = 3.0V 0.55 VCC = 2.3V - 12 VCC = 2.7V - 12 VCC = 3.0V - 24 VCC = 2.3V 12 VCC = 2.7V 12 VCC = 3.0V 24 3 Units mA PS8086B 10/07/98 PI74ALVCH16240 Inverting 16-Bit Buffer Driver with 3-State Outputs 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 DC Electrical Characteristics-Continued (Over the Operating Range, TA = 40°C to +85°C, VCC = 3.3V ±10%) Te s t Conditions (1) Parame te rs De s cription IIN Input Current VIN = VCC or GND, VCC = 3.6V Input Hold Current IIN (HOLD) Typ.(2) M in. M ax. ±5 VIN = 0.7V, VCC = 2.3V 45 VIN = 1.7V, VCC = 2.3V - 45 VIN = 0.8V, VCC = 3.0V 75 VIN = 2.0V, VCC = 3.0V - 75 VIN = 0 to 3.6V, VCC = 3.6V ±500 IOZ Output Current (3- STATE Outputs) VOUT = VCC or GND, VCC = 3.6V ±10 ICC Supply Current VCC = 3.6V, IOUT = 0mA, VIN = GND or VCC 40 DICC Supply Current per Input @ TTL HIGH VCC = 3.0V to 3.6V One Input at VCC - 0.6V Other Inputs at VCC or GND 750 Control Inputs CI Outputs CO mA 3 VIN = VCC or GND, VCC = 3.3V Data Inputs Units 6 VO = VCC or GND, VCC = 3.3V pF 7 Notes: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, +25°C ambient and maximum loading. 3. Unused Control Inputs must be held HIGH or LOW to prevent them from floating. Switching Characteristics over Operating Range(1) Parame te rs From (INPUT) To (OUTPUT) tPD A tEN tDIS VCC = 2.5V ± 0.2V M in.(2) M ax. Y 1.0 OE Y OE Y VCC = 2.7V M in.(2) VCC = 3.3V ± 0.3V M ax. M in.(2) M ax. 5.3 5.3 1.0 3.9 1.0 6.4 6.1 1.0 5.0 1.5 5.4 4.8 1.0 4.4 0 10 10 0 10 Units ns D e s cription Dt/Dv(3) Input Transition Rise or Fall 0 ns/V Notes: 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. Recommended operating condition. Operating Characteristics, TA = 25ºC Parame te r CPD Power Dissipation Capacitance Te s t Conditions Outputs Enabled Outputs Disabled CL = 50pF, f = 10 MHz VCC = 2.5V ± 0.2V VCC = 3.3V ± 0.3V Typical 16 19 4 5 Units pF Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 4 PS8086B 10/07/98