ETC TMS320VC5441GGU532

TMS320VC5441 Fixed-Point
Digital Signal Processor
Data Manual
Literature Number: SPRS122E
December 1999 – Revised April 2002
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Printed on Recycled Paper
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated
REVISION HISTORY
REVISION
DATE
PRODUCT STATUS
HIGHLIGHTS
*
December 1999
Product Preview
Original
A
November 2000
Product Preview
Converted from data sheet to data manual format and
updated characteristics data.
B
May 2001
Product Preview
Revised signal descriptions table and updated characteristics
data
C
July 2001
Production Data
Revised electrical characteristics to reflect production data.
D
December 2001
Production Data
Updated characteristics data
E
April 2002
Production Data
Updated characteristic data
iii
Contents
Contents
Section
Page
1
TMS320VC5441 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Migration From the 5421 to the 5441 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
Pin Assignments for the GGU Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2
Pin Assignments for the PGF Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
3
3
3
5
7
3
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Memory Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2
On-Chip Dual-Access RAM (DARAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.3
On-Chip Two-Way Shared RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.4
Extended Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.5
Extended Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.6
Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.7
Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.8
I/O Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.9
Multicore Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.10
Device Bootload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
On-Chip Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Direct Memory Access (DMA) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
16-Bit Bidirectional Host-Port Interface (HPI16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
Multichannel Buffered Serial Port (McBSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4
Hardware Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5
Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6
Software-Programmable Phase-Locked Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7
General-Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8
Chip Subsystem ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.9
Data Memory Map Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Memory-Mapped Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
McBSP Control Registers and Subaddresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
DMA Subbank Addressed Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7
IDLE3 Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8
Emulating the 5441 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
14
14
18
18
19
19
19
19
19
20
20
20
20
24
29
33
35
40
42
44
44
45
47
48
50
52
52
4
Documentation Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
5
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
Electrical Characteristics Over Recommended Operating Case Temperature
Range (Unless Otherwise Noted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
54
54
December 1999 – Revised April 2002
SPRS122E
55
v
Contents
Section
5.4
5.5
5.6
Package Thermal Resistance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Parameter Symbology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.1
Divide-By-Two, Divide-By-Four, and Bypass Clock Options – PLL Disabled . . . . .
5.6.2
Multiply-By-N Clock Option – PLL Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset, x_BIO, and Interrupt Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Flag (x_XF), Timer (x_TOUT), and Watchdog Timer Output (x_WTOUT) Timings . .
General-Purpose Input/Output (GPIO) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multichannel Buffered Serial Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10.1
McBSP0/1/2 Transmit and Receive Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10.2
McBSP0 General-Purpose I/O Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host-Port Interface (HPI16) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
56
57
57
58
59
61
62
63
63
66
67
Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
Ball Grid Array Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Low-Profile Quad Flatpack Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
75
76
5.7
5.8
5.9
5.10
5.11
6
vi
Page
SPRS122E
December 1999 – Revised April 2002
Figures
List of Figures
Figure
Page
2–1
2–2
169-Ball GGU MicroStar BGA (Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
176-Pin PGF Low-Profile Quad Flatpack (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
5
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
3–14
3–15
3–16
3–17
3–18
3–19
3–20
3–21
3–22
3–23
3–24
3–25
3–26
3–27
3–28
3–29
3–30
Overall Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Subsystem Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem A CPU Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem B CPU Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem C CPU Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem D CPU Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detailed Memory Map of Local Data Memory Relative to CPU Subsystems A, B, C, and D . . . . .
Subsystem A Local DMA Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem B Local DMA Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem C Local DMA Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem D Local DMA Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interfacing to the HPI-16 in Non-Multiplexed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSCR Register Bit Layout for Subsystem A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XA Multiplexer for HPI Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Control Register (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multichannel Control Register 2 for McBSPx (MCR2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multichannel Control Register 1 for McBSPx (MCR1x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive Channel Enable Registers Bit Layout for Partitions A to H . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit Channel Enable Registers Bit Layout for Partitions A to H . . . . . . . . . . . . . . . . . . . . . . . . .
SA Multiplexer for McBSP1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Control Register (TCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Second Control Register (TSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer Control Register (WDTCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer Second Control Register (WDTSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Operation State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Mode Register (CLKMD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose I/O Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chip Subsystem ID Register (CSIDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Memory Map Register (DMMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Layout of the IMR and IFR Registers for Each Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
16
17
18
21
21
22
22
26
27
28
29
30
30
31
31
32
33
35
36
38
39
40
43
44
44
51
5–1
5–2
5–3
5–4
5–5
3.3-V Test Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Divide-by-Two Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Multiply-by-One Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset and x_BIO Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
57
58
59
60
December 1999 – Revised April 2002
SPRS122E
vii
Figures
Figure
Page
5–6
5–7
5–8
5–9
5–10
5–11
5–12
5–13
5–14
5–15
5–16
5–17
5–18
5–19
External Flag (x_XF) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer (x_TOUT) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer (x_WTOUT) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0/1/2 Receive Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0/1/2 Transmit Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0 General-Purpose I/O Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplexed Read Timings Using HAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplexed Read Timings With HAS Held High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplexed Write Timings Using HAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplexed Write Timings With HAS Held High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nonmultiplexed Read Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nonmultiplexed Write Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI_SEL1 and HPI_SEL2 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
61
62
65
65
66
69
70
71
72
73
74
74
6–1
6–2
TMS320VC5441 169-Ball MicroStar BGA Plastic Ball Grid Array (GGU) Package . . . . . . . . . . . . .
TMS320VC5441 176-Pin Low-Profile Quad Flatpack (PGF) Package . . . . . . . . . . . . . . . . . . . . . . .
75
76
viii
SPRS122E
December 1999 – Revised April 2002
Tables
List of Tables
Table
Page
2–1
2–2
2–3
Pin Assignments for TMS320VC5441GGU (169-Ball BGA Package) . . . . . . . . . . . . . . . . . . . . . . .
Pin Assignments for TMS320VC5441PGF (176-Pin LQFP Package) . . . . . . . . . . . . . . . . . . . . . .
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
6
7
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
3–14
3–15
3–16
3–17
3–18
3–19
3–20
3–21
3–22
3–23
3–24
3–25
3–26
3–27
DMA Synchronization Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Channel Interrupt Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI Local/Shared Memory Selection Via HA[20] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI Local/Shared Memory Selection Via HA[18] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSCR Register Bit Functions for Subsystem A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI Module Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Rate Generator Clock Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive Channel Enable Registers for Partitions A to H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit Channel Enable Registers for Partitions A to H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCR Bit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSCR Bit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WDTCR Bit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WDTSCR Bit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Mode Register (CLKMD) Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiplier Related to PLLNDIV, PLLDIV, and PLLMUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCO Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCO Lockup Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Initialization at Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose I/O Control Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chip Subsystem ID Register Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Memory Map Register Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processor Memory-Mapped Registers for Each DSP Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Memory-Mapped Registers for Each DSP Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Control Registers and Subaddresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Subbank Addressed Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5441 Interrupt Locations and Priorities for Each DSP Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Functions for IMR and IFR Registers for Each DSP Subsystem . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
26
27
28
30
31
31
34
35
37
38
41
41
41
42
42
43
44
44
45
46
47
48
50
51
5–1
5–2
5–3
5–4
5–5
5–6
5–7
Thermal Resistance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Divide-By-Two, Divide-By-Four, and Bypass Clock Options Timing Requirements . . . . . . . . . . . .
Divide-By-Two, Divide-By-Four, and Bypass Clock Options Switching Characteristics . . . . . . . . .
Multiply-By-N Clock Option Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiply-By-N Clock Option Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset, x_BIO, and Interrupt Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Flag (x_XF), Timer (x_TOUT), and Watchdog Timer Output (x_WTOUT)
Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0/1/2 Transmit and Receive Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0/1/2 Transmit and Receive Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
57
57
58
58
59
5–8
5–9
5–10
5–11
December 1999 – Revised April 2002
SPRS122E
61
62
62
63
64
ix
Tables
Table
5–12
5–13
5–14
5–15
x
Page
McBSP0 General-Purpose I/O Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP0 General-Purpose I/O Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI16 Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPI16 Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPRS122E
66
66
67
68
December 1999 – Revised April 2002
Features
1
TMS320VC5441 Features
532-MIPS Quad-Core DSP Consisting of
Four Independent Subsystems
Each Core has an Advanced Multibus
Architecture With Three Separate 16-Bit
Data Memory Buses and One Program Bus
40-Bit Arithmetic Logic Unit (ALU)
Including a 40-Bit Barrel-Shifter and Two
40-Bit Accumulators Per Core
Each Core has a 17-Bit × 17-Bit Parallel
Multiplier Coupled to a 40-Bit Adder for
Non-Pipelined Single-Cycle Multiply/
Accumulate (MAC) Operations
Each Core has a Compare, Select, and
Store Unit (CSSU) for the Add/Compare
Selection of the Viterbi Operator
Each Core has an Exponent Encoder to
Compute an Exponent Value of a 40-Bit
Accumulator Value in a Single Cycle
Each Core has Two Address Generators
With Eight Auxiliary Registers and Two
Auxiliary Register Arithmetic Units
(ARAUs)
Total 640K-Word × 16-Bit Dual-Access
On-Chip RAM (256K-Word x 16-Bit Shared
Memory and 96K-Word x 16-Bit Local
Memory Per Subsystem)
Single-Instruction Repeat and
Block-Repeat Operations
Instructions With 32-Bit Long Word
Operands
Instructions With 2 or 3 Operand Reads
Fast Return From Interrupts
Arithmetic Instructions With Parallel Store
and Parallel Load
Conditional Store Instructions
Output Control of CLKOUT
Output Control of Timer Output (TOUT)
Power Consumption Control With IDLE1,
IDLE2, and IDLE3 Instructions
Dual 1.6-V (Core) and 3.3-V (I/O) Power
Supplies for Low-Power, Fast Operations
7.5-ns Single-Cycle Fixed-Point Instruction
Twenty-Four Channels of Direct Memory
Access (DMA) for Data Transfers With No
CPU Loading (Six Channels Per
Subsystem)
Twelve Multichannel Buffered Serial Ports
(McBSPs), Each With 128-Channel
Selection Capability (Three McBSPs per
Subsystem)
16-Bit Host-Port Interface (HPI)
Software-Programmable Phase-Locked
Loop (PLL) Provides Several Clocking
Options (Requires External TTL Oscillator)
On-Chip Scan-Based Emulation Logic,
IEEE Standard 1149.1 (JTAG) BoundaryScan Logic
Four Software-Programmable Timers
(One Per Subsystem)
Four Software-Programmable Watchdog
Timers (One Per Subsystem)
Sixteen General-Purpose I/Os
(Four Per Subsystem)
Provided in 176-pin Plastic Low-Profile
Quad Flatpack (LQFP) Package
(PGF Suffix)
Provided in 169-ball MicroStar BGA
Package (GGU Suffix)
MicroStar BGA is a trademark of Texas Instruments.
Other trademarks are the property of their respective owners.
† IEEE Standard 1149.1-1990, Standard Test-Access Port and Boundary Scan Architecture.
December 1999 – Revised April 2002
SPRS122E
1
Introduction
2
Introduction
This section describes the main features of the TMS320VC5441 digital signal processor (DSP), lists the pin
assignments, and describes the function of each pin. This data manual also provides a detailed description
section, electrical specifications, parameter measurement information, and mechanical data about the
available packaging.
NOTE: This data manual is designed to be used in conjunction with the TMS320C54x  DSP Functional
Overview (literature number SPRU307).
2.1
Description
The TMS320VC5441 fixed-point digital signal processor is a quad-core solution running at 532-MIPS
performance. The 5441 consists of four DSP subsystems with shared program memory. Each subsystem
consists of one TMS320C54x DSP core, 32K-word program/data DARAM, 64K-word data DARAM, three
multichannel buffered serial ports, DMA logic, one watchdog timer, one general-purpose timer, and other
miscellaneous circuitry.
The 5441 also contains a host-port interface (HPI) that allows the 5441 to be viewed as a memory-mapped
peripheral to a host processor.
Each subsystem has its separate program and data spaces, allowing simultaneous accesses to program
instructions and data. Two read operations and one write operation can be performed in one cycle. Instructions
with parallel store and application-specific instructions can fully utilize this architecture. Furthermore, data can
be transferred between program and data spaces. Such parallelism supports a powerful set of arithmetic,
logic, and bit-manipulation operations that can all be performed in a single machine cycle. The 5441 includes
the control mechanisms to manage interrupts, repeated operations, and function calls. In addition, the 5441
has a total of 256K words of shared program memory (128K words shared by subsystems A and B, and
another 128K words shared by subsystems C and D).
The 5441 is intended as a high-performance, low-cost, high-density DSP for remote data access or voice-over
IP subsystems. It is designed to maintain the current modem architecture with minimal hardware and software
impacts, thus maximizing reuse of existing modem technologies and development efforts.
The 5441 is offered in two temperature ranges and individual part numbers are shown below. (Please note
that the industrial temperature device part numbers do not follow the typical numbering tradition.)
Commercial temperature devices (0°C to 85°C)
TMS320VC5441PGF532 (176-pin LQFP)
TMS320VC5441GGU532 (169-ball BGA)
Industrial temperature range devices (–40°C to 100°C)
TMS320VC5441APGF532 (176-pin LQFP)
TMS320VC5441AGGU532 (169-ball BGA)
NOTE: Leading “x” in signal names identifies the subsystem; x = A, B, C, or D for subsystem A, B, C,
or D, respectively. Trailing “n” in signal names identifies the McBSP; n = 0, 1, or 2 for McBSP0, McBSP1,
or McBSP2, respectively.
TMS320C54x is a trademark of Texas Instruments.
2
SPRS122E
December 1999 – Revised April 2002
Introduction
2.2
Migration From the 5421 to the 5441
Customers who are migrating from the 5421 to the 5441 need to take into account the following differences
between the two devices.
•
•
•
•
•
•
•
•
•
•
•
2.3
The 5441 provides four cores in a 169-ball ball grid array (BGA) and a 176-pin low-profile quad flatpack
(LQFP).
The 5441 does not have a XIO interface for external memory connection.
Each subsystem includes a 32K-word DARAM program/data memory and a 64K-word DARAM data
memory.
The DMA has been changed and now provides no access to external memory.
The HPI and DMA memory maps have been changed to incorporate the new 5441 memory structure.
The 2K words of ROM on the 5421 is not implemented on the 5441.
The four McBSP1s and four McBSP2s have been internally multiplexed onto two sets of external pins.
The HPI_SEL1 and HPI_SEL2 pins on 5441 are used to facilitate HPI module selection among the four
subsystems.
The 5441 provides four watchdog timers (one per subsystem).
GPIO0 and GPIO1 pins are multiplexed with x_XF and x_BIO pins, respectively.
Only the global reset (RESET) will reset the PLL.
Pin Assignments
Figure 2–1 illustrates the ball locations for the 169-ball ball grid array (BGA) package and is used in
conjunction with Table 2–1 to locate signal names and ball grid numbers. Figure 2–2 illustrates the pin
locations for the 176-pin low-profile quad flatpack (LQFP); Table 2–2 lists each pin number and its associated
pin name for this package.
2.3.1 Pin Assignments for the GGU Package
N
M
L
K
J
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10 11 12 13
Figure 2–1. 169-Ball GGU MicroStar BGA (Bottom View)
December 1999 – Revised April 2002
SPRS122E
3
Introduction
Table 2–1. Pin Assignments for TMS320VC5441GGU (169-Ball BGA Package)†
BALL #
SIGNAL NAME
BALL #
SIGNAL NAME
BALL #
SIGNAL NAME
BALL #
SIGNAL NAME
A1
HA[0]/HCNTL0
A2
A3
B_BDR0
CVDD
A6
VSS
DVDD
A4
A5
DVDD
VSS
A8
A9
A10
D_BDR0
A11
B1
HA[1]/HCNTL1
B2
VSS
B_BFSX0
A12
A13
CVDD
D_BFSX0
VSS
DVDD
B3
B_BFSR0
B4
B_BDX0
B5
HD[7]
B7
HD[3]
HD[0]
B9
CVDD
CVDD
B6
B8
B10
D_GPIO0/D_XF
B11
D_BDX0
B12
D_BFSR0
B13
HA[18]
C1
C2
HA[3]/B_HINT
C3
B_GPIO1/B_BIO
C4
B_GPIO0/B_XF
C5
VSS
CVDD
C6
B_BCLKR0
C7
HD[4]
C8
D_GPIO3/D_TOUT
C9
CVDD
C10
D_BCLKX0
C11
HA[17]
C12
HA[15]
C13
CLKMD
B_NMI
D3
B_RS
D4
VSS
HA[4]/C_HINT
D1
D2
D5
CVDD
D6
B_BCLKX0
D7
HD[5]
D8
D_GPIO1/D_BIO
D9
CVDD
D10
D_BCLKR0
D11
D_RS
D12
D_INT
D13
TRST
E1
DVDD
E2
TESTB
E3
TDI
E4
B_INT
HD[1]
A7
E5
HA[2]/A_HINT
E6
B_GPIO3/B_TOUT
E7
HD[6]
E8
E9
D_GPIO2/D_WTOUT
E10
TESTD
E11
TMS
E12
TCK
E13
DVDD
F1
F2
HCS
HAS
F5
F6
VSS
B_GPIO2/B_WTOUT
F3
F4
VSSA
CLKIN
F7
HD[2]
F8
HA[16]
F9
D_NMI
F10
EMU1/OFF
F11
HPI_SEL2
F12
HPI_SEL1
F13
G1
CVDD
EMU0
G4
G5
VCCA
BCLKX2
G2
G3
VSS
BCLKR2
G6
HRDY
G7
BDR1
G8
HMODE
G9
HDS2
G10
C_NMI
G11
RESET
G12
HR/W
G13
BFSR2
H3
BFSX2
H4
CVDD
CLKOUT
H1
H2
H5
VSS
A_INT
H6
HA[7]
H7
HD[9]
H8
C_GPIO1/C_BIO
H9
BCLKX1
H10
BCLKR1
H11
BFSR1
H12
BFSX1
H13
J1
DVDD
J2
BDR2
J3
BDX2
J4
VSS
A_RS
J5
A_GPIO1/A_BIO
J6
HD[8]
J7
HD[13]
J8
C_BCLKR0
J9
HA[11]
J10
C_INT
J11
C_RS
J12
BDX1
J13
DVDD
K1
K2
A_NMI
K3
TDO
K4
A_GPIO3/A_TOUT
K5
VSS
CVDD
K6
A_GPIO2/A_WTOUT
K7
HD[12]
K8
C_BCLKX0
K9
K10
HA[13]
K11
HA[14]
K12
TESTC
K13
CVDD
HDS1
L1
HA[5]/D_HINT
L2
HA[6]
L3
HA[8]
L4
A_GPIO0/A_XF
L5
CVDD
L6
A_BCLKR0
L7
HD[11]
L8
HD[15]
L9
CVDD
L10
C_GPIO0/C_XF
L11
C_GPIO2/C_WTOUT
L12
HA[12]
L13
HA[9]
M3
A_BFSR0
M4
VSS
A_BDR0
M1
M2
M6
A_BCLKX0
M7
HD[10]
M8
HD[14]
M9
VSS
CVDD
CVDD
M10
C_GPIO3/C_TOUT
M11
C_BDX0
M12
C_BFSR0
M13
HA[10]
N1
A_BFSX0
N2
N3
A_BDX0
CVDD
N6
N7
VSS
DVDD
N4
N5
DVDD
VSS
N8
N9
CVDD
N10
C_BDR0
N11
VSS
N12
VSS
DVDD
N13
C_BFSX0
M5
† Cells highlighted in gray indicate pins that perform a multiplexed function.
4
SPRS122E
December 1999 – Revised April 2002
Introduction
2.3.2 Pin Assignments for the PGF Package
132
89
133
88
176
45
1
44
Figure 2–2. 176-Pin PGF Low-Profile Quad Flatpack (Top View)
December 1999 – Revised April 2002
SPRS122E
5
Introduction
Table 2–2. Pin Assignments for TMS320VC5441PGF (176-Pin LQFP Package)†
PIN NO.
SIGNAL NAME
PIN NO.
SIGNAL NAME
PIN NO.
SIGNAL NAME
PIN NO.
SIGNAL NAME
1
HA[0]/HCNTL0
2
HA[1]/HCNTL1
3
HA[2]/A_HINT
4
HA[3]/B_HINT
5
HA[4]/C_HINT
6
7
8
B_RS
9
B_NMI
10
VSS
B_INT
11
VSS
CLKMD
12
TDI
13
TESTB
14
DVDD
15
HAS
16
HCS
17
18
CLKIN
20
HRDY
22
VSSA
CVDD
19
21
VSS
VCCA
23
CVDD
24
EMU0
25
BCLKR2
26
BCLKX2
27
28
BFSR2
29
BFSX2
30
CLKOUT
31
VSS
DVDD
32
BDR2
33
BDX2
34
A_RS
36
A_NMI
A_INT
38
VSS
TDO
35
37
39
HA[5]/D_HINT
40
HA[6]
41
HA[7]
42
HA[8]
43
HA[9]
A_BFSX0
46
DVDD
47
VSS
A_GPIO1/A_BIO
44
45
48
A_BFSR0
49
A_GPIO3/A_TOUT
50
51
A_GPIO0/A_XF
52
A_BDR0
53
CVDD
54
VSS
A_BDX0
55
CVDD
58
A_GPIO2/A_WTOUT
59
CVDD
A_BCLKR0
56
57
60
CVDD
A_BCLKX0
61
62
HD[8]
63
HD[9]
64
DVDD
65
VSS
DVDD
66
HD[10]
67
HD[11]
68
HD[12]
69
HD[13]
70
71
HD[14]
72
HD[15]
73
C_BCLKX0
74
VSS
CVDD
75
CVDD
76
CVDD
77
C_BDR0
78
CVDD
79
C_GPIO3/C_TOUT
80
C_BCLKR0
81
C_GPIO0/C_XF
82
83
C_BDX0
84
C_GPIO1/C_BIO
85
C_GPIO2/C_WTOUT
86
VSS
DVDD
87
DVDD
88
C_BFSR0
89
C_BFSX0
90
HA[10]
91
HA[11]
92
HA[12]
93
HA[13]
94
95
HA[14]
96
TESTC
97
C_INT
98
VSS
HDS1
99
C_RS
100
BDX1
101
BDR1
102
BCLKR1
103
BFSR1
BFSX1
106
107
108
HMODE
109
CVDD
110
VSS
HR/W
DVDD
BCLKX1
104
105
111
RESET
112
C_NMI
113
HDS2
114
115
HPI_SEL1
116
HPI_SEL2
117
EMU1/OFF
118
VSS
DVDD
119
TCK
120
TMS
121
TRST
122
TESTD
123
D_INT
124
D_NMI
125
D_RS
126
127
HA[15]
HA[16]
130
131
VSS
HA[18]
128
129
VSS
HA[17]
132
D_BFSR0
133
D_BFSX0
134
DVDD
136
D_GPIO2/D_WTOUT
D_BDX0
138
DVDD
D_BCLKR0
135
137
139
140
D_BCLKX0
141
D_GPIO0/D_XF
142
CVDD
143
VSS
D_BDR0
144
CVDD
145
CVDD
146
CVDD
147
D_GPIO1/D_BIO
148
D_GPIO3/D_TOUT
149
HD[0]
150
151
HD[1]
152
HD[2]
153
DVDD
154
VSS
HD[3]
155
HD[4]
156
HD[5]
157
HD[6]
158
HD[7]
160
B_BCLKR0
B_BCLKX0
162
163
CVDD
164
165
B_BDR0
166
VSS
CVDD
CVDD
159
161
167
B_BDX0
168
CVDD
B_GPIO3/B_TOUT
169
B_GPIO0/B_XF
170
B_BFSR0
172
B_GPIO2/B_WTOUT
B_GPIO1/B_BIO
174
VSS
DVDD
171
173
175
DVDD
176
B_BFSX0
† Cells highlighted in gray indicate pins that perform a multiplexed function.
6
SPRS122E
December 1999 – Revised April 2002
Introduction
2.4
Signal Descriptions
Table 2–3 lists all the signals, grouped by function. See Section 2.3 for the exact pin locations based on the
package type. Pin functions highlighted in gray are secondary (multiplexed) functions.
Table 2–3. Signal Descriptions
NAME
TYPE†
DESCRIPTION
HOST-PORT INTERFACE SIGNALS
HA18 (MSB)
HA17
HA16
HA15
HA14
HA13
HA12
HA11
HA10
HA9
HA8
HA7
HA6
HPI address pins when HPI is in nonmultiplexed mode. HA18 is used to facilitate program (shared) memory and data
(local) memory selection.
I‡
The pins include bus holders to reduce power dissipation caused by floating, unused pins. The bus holders also
eliminate the need for external pullup resistors on unused pins. When the address bus is not being driven by the
external host, the bus holders keep address pins at the last driven logic level. The address bus keepers are disabled
at global reset or subsystem A reset, and can be enabled/disabled via the BHA bit of the BSCR register in subsystem A.
SECONDARY
HA5
HA4
HA3
HA2
D_HINT
C_HINT
B_HINT
A_HINT
O/Z§
HA1
HA0 (LSB)
HCNTL1
HCNTL0
I
HD15 (MSB)
Parallel bidirectional data bus. These pins are the HPI data bus.
HD14
HD13
The pins include bus holders to reduce power dissipation caused by floating, unused pins. The bus holders also
HD12
eliminate the need for external pullup resistors on unused pins. When the data bus is not being driven by the 5441,
HD11
the bus holders keep data pins at the last driven logic level. The data bus keepers are disabled at global reset or
HD10
subsystem A reset, and can be enabled/disabled via the BHD bit of the BSCR register in subsystem A.
HD9
HD8
I/O/Z‡§
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0 (LSB)
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
December 1999 – Revised April 2002
SPRS122E
7
Introduction
Table 2–3. Signal Descriptions (Continued)
NAME
TYPE†
DESCRIPTION
HOST-PORT INTERFACE SIGNALS (CONTINUED)
HPI mode select. When this pin is low, it selects the HPI multiplexed address/data mode. The multiplexed address/data
mode allows hosts with multiplexed address/data lines access to the HPI registers HPIA, HPIC, and HPID.
Host-to-DSP and DSP-to-host interrupts are supported in this mode.
HMODE¶
I
When HMODE is high, it selects the HPI nonmultiplexed mode. HPI nonmultiplexed mode allows hosts with separate
address/data buses to access the HPI address range by way of the 19-bit address bus and the HPI data (HPID) register
via the 16-bit data bus. Host-to-DSP and DSP-to-host interrupts are not supported in this mode.
HAS¶#
I
HPI address latch enable (ALE) or address strobe input. Hosts with multiplexed address and data pins require HAS
to latch the address in the HPIA register. This signal is used only in HPI multiplexed address/data mode
(HMODE = 0).
HRDY
O/Z§
HPI data ready output. The ready output informs the host when the HPI is ready for the next transfer. While driving,
it is in output state and while not driving, it is in high-Z state.
HR/W
¶
HDS1¶#
HDS2¶#
I
HPI read/write strobe. This signal is used by the host to control the direction of an HPI transfer.
I
HPI data strobes
strobes. Driven by the host read and write strobes to control HPI transfers
transfers.
HCS¶#
I
HPI chip select. Must be active during HPI transfers and can remain active between concurrent transfers.
PRIMARY
D_HINT
C_HINT
B_HINT
A_HINT
O/Z§
HA5
HA4
HA3
HA2
I
I
Host interrupt pins. HPI can interrupt the host by asserting this low. The host can clear this
interrupt by writing a “1” to the HINT bit of the HPIC register. Only supported in HPI
multiplexed address/data mode (HMODE pin low)
HCNTL1
HCNTL0
I
HA1
HA0
HPI control pins. These pins select a host access to the HPIA, HPIC, and HPID registers.
Only supported in HPI multiplexed address/data mode (HMODE pin low)
HPI_SEL1
HPI_SEL2
I
Subsystem HPI module select
MULTICHANNEL BUFFERED SERIAL PORTS 0, 1, AND 2 SIGNALS
A_BCLKR0#
B_BCLKR0#
C_BCLKR0#
D_BCLKR0#
I/O/Z§
Receive clocks. x_BCLKR0 serve as the serial shift clocks for the buffered serial-port receiver. Input from an external
clock source for clocking data into the McBSP. When not being used as clocks, these pins can be used as
general-purpose I/Os by setting RIOEN = 1.
x_BCLKR0 can be configured as outputs by way of the CLKRM bit in the PCR register.
A_BCLKX0#
B_BCLKX0#
C_BCLKX0#
D_BCLKX0#
I/O/Z§
Transmit clocks. Clock signals used to clock data from the transmit register. These pins can also be configured as
inputs by setting CLKXM = 0 in the PCR register. x_BCLKX0 can be sampled as inputs by way of the IN1 bit in the
SPC register. When not being used as clocks, these pins can be used as general-purpose I/Os by setting XIOEN = 1.
A_BDR0
Buffered serial data receive (input) pins. When not being used as data-receive pins, these pins can be used as
B_BDR0
I
general-purpose I/Os by setting RIOEN = 1.
C_BDR0
D_BDR0
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
8
SPRS122E
December 1999 – Revised April 2002
Introduction
Table 2–3. Signal Descriptions (Continued)
NAME
TYPE†
DESCRIPTION
MULTICHANNEL BUFFERED SERIAL PORTS 0, 1, AND 2 SIGNALS (CONTINUED)
A_BDX0
B_BDX0
C_BDX0
D_BDX0
O/Z§
Buffered serial-port transmit (output) pins. When not being used as data-transmit pins, x_BDX0 can be used as
general-purpose I/Os by setting XIOEN = 1.
A_BFSR0
B_BFSR0
C_BFSR0
D_BFSR0
I/O/Z§
Frame synchronization pins for buffered serial-port input data. The x_BFSR0 pulse initiates the receive-data process
over x_BDR0. When not being used as data-receive synchronization pins, these pins can be used as general-purpose
I/Os by setting RIOEN = 1.
I/O/Z§
Buffered serial-port frame synchronization pins for transmitting data. The x_BFSX0 pulse initiates the transmit-data
process over the x_BDX0 pin. If x_RS is asserted when x_BFSX0 is configured as output, then x_BFSX0 is turned
into input mode by the reset operation. When not being used as data-transmit synchronization pins, these pins can
be used as general-purpose I/Os by setting XIOEN = 1.
A_BFSX0
B_BFSX0
C_BFSX0
D_BFSX0
BCLKR1#
BCLKX1#
Receive clock, multiplexed McBSP1
I
BDR1
BDX1
BFSR1
BFSX1
BCLKR2#
BCLKX2#
Receive data, multiplexed McBSP1
O/Z§
I
BFSR2
BFSX2
Transmit data, multiplexed McBSP1
Receive frame sync, multiplexed McBSP1
Transmit frame sync, multiplexed McBSP1
Receive clock, multiplexed McBSP2
I
BDR2
BDX2
Transmit clock, multiplexed McBSP1
Transmit clock, multiplexed McBSP2
Receive data, multiplexed McBSP2
O/Z§
I
Transmit data, multiplexed McBSP2
Receive frame sync, multiplexed McBSP2
Transmit frame sync, multiplexed McBSP2
CLOCKING SIGNALS
Master clock output signal. CLKOUT cycles at the machine-cycle rate of the CPU. The internal machine cycle is
bounded by the falling edges of this signal. The CLKOUT pin can be turned off by writing a “1” to the CLKOUT bit of
the PMST register.
Multiplexed as shown below based on the selection bits in the GPIO register
CLKOUT
O/Z§
GPIO[7]
A_CLKOUT
B_CLKOUT||
C_CLKOUT||
D_CLKOUT||
CLKIN#
CLKMD#
I
GPIO[6]
0
0
0
1
1
0
1
1
(default)
Input clock to the device. CLKIN connects to a PLL.
I
Clock mode configuration pin at reset. When CLKMD = 0, bypasses PLL; when CLKMD = 1, CLKINx2
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
December 1999 – Revised April 2002
SPRS122E
9
Introduction
Table 2–3. Signal Descriptions (Continued)
NAME
TYPE†
DESCRIPTION
GENERAL-PURPOSE I/O PINS
A_GPIO0/
A_XF
Subsystem A GPIO0/
Subsystem A external flag output
B_GPIO0/
B_XF
Subsystem B GPIO0/
Subsystem B external flag output
C_GPIO0/
C_XF
I/O/Z§
Subsystem C GPIO0/
Subsystem C external flag output
D_GPIO0/
D_XF
Subsystem D GPIO0/
Subsystem D external flag output
A_GPIO1/
A_BIO
Subsystem A GPIO1/
Subsystem A branch control input
B_GPIO1/
B_BIO
Subsystem B GPIO1/
Subsystem B branch control input
C_GPIO1/
C_BIO
I/O/Z§
Subsystem C GPIO1/
Subsystem C branch control input
D_GPIO1/
D_BIO
Subsystem D GPIO1/
Subsystem D branch control input
A_GPIO2/
A_WTOUT
Subsystem A GPIO2/
Subsystem A watchdog timer output
B_GPIO2/
B_WTOUT
Subsystem B GPIO2/
Subsystem B watchdog timer output
C_GPIO2/
C_WTOUT
I/O/Z§
Subsystem C GPIO2/
Subsystem C watchdog timer output
D_GPIO2/
D_WTOUT
Subsystem D GPIO2/
Subsystem D watchdog timer output
A_GPIO3/
A_TOUT
Subsystem A GPIO3/
Subsystem A timer output
B_GPIO3/
B_TOUT
Subsystem B GPIO3/
Subsystem B timer output
C_GPIO3/
C_TOUT
I/O/Z§
Subsystem C GPIO3/
Subsystem C timer output
These pins act according to the
general-purpose I/O register. The
x_XF bit must be set to “1”
1 to drive the
x_XF output on the pin. If x_XF=0,
then these pins are general-purpose
I/Os
I/Os.
These pins act according to the
general-purpose I/O register. The
x_BIO bit must be set to “1”
1 to drive the
x_BIO input into the device. If
x_BIO=0, then these pins are General-purpose I/O pins (softwareprogrammable I/O signal)
signal). Values
general-purpose
general purpose I/Os.
I/Os
can be latched (output) by writing into
the GPIO register. The states of GPIO
pins (inputs) can be determined by
reading the GPIO register. The GPIO
The watchdog enable (WDEN) bit in direction is also programmable by
the
watchdog
timer
register way of the DIRn field in the register.
(WDTSCR) is used to multi
lex the
multiplex
watchdog timer output and GPIO2. If
WDEN=0, then these pins are
general purpose I/Os.
general-purpose
I/Os
These pins act according to the
general-purpose I/O register. The
X_TOUT bit must be set to “1”
1 to drive
the timer output on the pin. If
X_TOUT=0, then these pins are
general purpose I/Os.
general-purpose
I/Os
D_GPIO3/
Subsystem D GPIO3/
D_TOUT
Subsystem D timer output
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
10
SPRS122E
December 1999 – Revised April 2002
Introduction
Table 2–3. Signal Descriptions (Continued)
NAME
TYPE†
DESCRIPTION
INITIALIZATION, INTERRUPT, AND RESET OPERATIONS
A_INT¶#
B_INT¶#
C_INT¶#
D_INT¶#
A_NMI¶#
B_NMI¶#
C_NMI¶#
D_NMI¶#
A_RS#
B_RS#
C_RS#
D_RS#
RESET#
I
External user interrupts. A_INT–D_INT are prioritized and are maskable by the interrupt mask register (IMR) and the
interrupt mode bit. The status of these pins can be polled and reset by way of the interrupt flag register (IFR).
I
Nonmaskable interrupts. x_NMI is an external interrupt that cannot be masked by way of the INTM bit or the IMR. When
x_NMI is activated, the processor traps to the appropriate vector location.
I
Reset. x_RS causes the digital signal processor (DSP) to terminate execution and causes a reinitialization of the CPU
and peripherals. When x_RS is brought to a high level, execution begins at location 0FF80h of program memory. x_RS
affects various registers and status bits.
I
Global/HPI reset. This signal resets the four subsystems and the HPI.
SUPPLY PINS
VCCA
CVDD
DVDD
VSS
Dedicated power supply that powers the PLL. VDD = 1.6 V
Dedicated power supply that powers the core CPUs. CVDD = 1.6 V
S
Dedicated power supply that powers the I/O pins. DVDD = 3.3 V
Digital ground. Dedicated ground plane for the device.
Analog ground. Dedicated ground for the PLL. VSSA can be connected to VSS if digital and analog grounds are not
separated.
VSSA
EMULATION/TEST PINS
TESTB||
TESTC||
TESTD||
No connection
TCK¶#
I
Standard test clock. This is normally a free-running clock signal with a 50% duty cycle. Changes on the test access
port (TAP) input signals TMS and TDI are clocked into the TAP controller, instruction register, or selected test-data
register on the rising edge of TCK. Changes at the TAP output signal (TDO) occur on the falling edge of TCK.
TDI¶
I
Test data input. Pin with an internal pullup device. TDI is clocked into the selected register (instruction or data) on a
rising edge of TCK.
TDO
O/Z§
Test data pin. The contents of the selected register is shifted out of TDO on the falling edge of TCK. TDO is in
high-impedance state except when the scanning of data is in progress.
TMS¶
I
Test mode select. Pin with internal pullup device. This serial control input is clocked into the TAP controller on the rising
edge of TCK.
TRST
I
Test reset. When high, TRST gives the scan system control of the operations of the device. If TRST is driven low, the
device operates in its functional mode and the IEEE 1149.1 signals are ignored. Pin with internal pulldown device.
EMU0
I/O/Z
Emulator interrupt 0 pin. When TRST is driven low, EMU0 must be high for the activation of the EMU1/OFF condition.
When TRST is driven high, EMU0 is used as an interrupt to or from the emulator system and is defined as I/O.
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
December 1999 – Revised April 2002
SPRS122E
11
Introduction
Table 2–3. Signal Descriptions (Continued)
NAME
TYPE†
DESCRIPTION
EMULATION/TEST PINS (CONTINUED)
Emulator interrupt 1 pin. When TRST is driven high, EMU1/OFF is used as an interrupt to or from the emulator system
and is defined as I/O. When TRST transitions from high to low, then EMU1 operates as OFF. EMU/OFF = 0 puts all
output drivers into the high-impedance state.
EMU1/OFF
I/O/Z
Note that OFF is used exclusively for testing and emulation purposes (and not for multiprocessing applications).
Therefore, for the OFF condition, the following conditions apply:
TRST = 0, EMU0 = 1, EMU1 = 0
† I = Input, O = Output, S = Supply, Z = High Impedance
‡ This pin has an internal bus holder controlled by way of the BSCR register in TMS320C54x cLEAD core of DSP subsystem A.
§ This pin is placed in high-impedance when the EMU1/OFF pin operates as OFF and when EMU1/OFF = 0, this case is exclusively for testing
and emulation purposes.
¶ This pin has an internal pullup resistor.
# These pins are Schmitt triggered inputs.
|| This pin is used by Texas Instruments for device testing and should be left unconnected.
This pin has an internal pulldown resistor.
NOTE: Pins highlighted in grey indicate the multiplexed function of the pin.
12
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3
Functional Overview
The functional overview in this section is based on the overall system block diagram in Figure 3–1 and the
typical subsystem block diagram in Figure 3–2.
GPIO
McBSP0
McBSP1
McBSP2
Shared P Bus
DSP
Subsystem A
DSP ID: 0000
DSP
Subsystem B
DSP ID: 0001
PLL
HPI
HPI
GPIO
McBSP0
McBSP1
McBSP2
SA1
McBSP1
SA2
McBSP2
XA
McBSP2
McBSP1
McBSP0
GPIO
HPI
HPI
DSP
Subsystem C
DSP ID: 0010
DSP
Subsystem D
DSP ID: 0011
Shared P Bus
McBSP2
McBSP1
McBSP0
GPIO
Figure 3–1. Overall Functional Block Diagram
DSP Subsystem
TMS320C54x cLEAD
(Core)
64K-Word
Data DARAM
P Bus
E Bus
D Bus
C Bus
P Bus
E Bus
D Bus
C Bus
E Bus
D Bus
C Bus
P Bus
P. C. D. E. Busses and Control Signals
32K-Word
Program/Data
DARAM
64K-Word
Program DARAM
M Bus
M Bus
DMA
M Bus
M Bus
3 × McBSP
Timer
M Bus
WDTimer
HPI
GPIO
HPI Bus
Shared P Bus
Figure 3–2. Typical Subsystem Functional Block Diagram
December 1999 – Revised April 2002
SPRS122E
13
Functional Overview
3.1
Memory
Each 5441 DSP subsystem maintains the peripheral register memory map and interrupt location/priorities of
the standard 5421. Each individual subsystem CPU memory map is illustrated in Figure 3–3 through
Figure 3–6.
The arbitration and access for local program/data memory and local data memory is based on a 16K-word
block size. The arbitration and access for all the shared memory is based on a 32K-word block size.
3.1.1 Memory Maps
Figure 3–3 through Figure 3–6 illustrate the CPU memory maps for subsystem A through subsystem D.
Figure 3–7 provides a detailed memory map of the local data memory relative to CPU subsystems A, B, C,
and D.
Memory Map with OVLY = 1
Page 0
Page 1
Page 2
Page 3
MPDA
MPDA
MPDA
MPDA
MPDA
MDA0
or
MDA1
MPAB0
MPAB1
MPAB2
MPAB3
0000h
8000h
FFFFh
Data Memory
Program Memory
Memory Map with OVLY = 0
Page 0
Page 1
Page 2
Page 3
MPAB3
MPAB3
MPAB3
MPAB3
MPAB2
ÒÒ
ÒÒ
ÒÒ
ÒÒ
0000h
MPDA
8000h
MDA0
or
MDA1
MPAB0
MPAB1
FFFFh
Data Memory
ÒÒ
ÒÒ
Program Memory
: reserved
NOTES: A. MPDA: local program/data memory in subsystem A
B. MDA: local data memory in subsystem A. MDA is controlled by the data memory map register (DMMR).
DMMR=0, MDA0 is mapped in 8000h – FFFFh.
DMMR=1, MDA1 is mapped in 8000h – FFFFh.
C. MPAB: shared program memory in subsystems A and B
Figure 3–3. Subsystem A CPU Memory Map
14
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Memory Map with OVLY = 1
Page 0
Page 1
Page 2
Page 3
MPDB
MPDB
MPDB
MPDB
MPDB
MDB0
or
MDB1
MPAB0
MPAB1
MPAB2
MPAB3
0000h
8000h
FFFFh
Data Memory
Program Memory
Memory Map with OVLY = 0
Page 0
Page 1
Page 2
Page 3
MPDB
MPAB3
MPAB3
MPAB3
MPAB3
MDB0
or
MDB1
MPAB0
MPAB1
MPAB2
ÒÒ
ÒÒ
ÒÒ
ÒÒ
0000h
8000h
FFFFh
Data Memory
Program Memory
ÕÕ
: reserved
NOTES: A. MPDB: local program/data memory in subsystem B
B. MDB: local data memory in subsystem B. MDB is controlled by the data memory map register (DMMR).
DMMR=0, MDB0 is mapped in 8000h – FFFFh.
DMMR=1, MDB1 is mapped in 8000h – FFFFh.
C. MPAB: shared program memory in subsystems A and B
Figure 3–4. Subsystem B CPU Memory Map
December 1999 – Revised April 2002
SPRS122E
15
Functional Overview
Memory Map with OVLY = 1
Page 0
Page 1
Page 2
Page 3
MPDC
MPDC
MPDC
MPDC
MPDC
MDC0
or
MDC1
MPCD0
MPCD1
MPCD2
MPCD3
0000h
8000h
FFFFh
Data Memory
Program Memory
Memory Map with OVLY = 0
Page 0
Page 1
Page 2
Page 3
MPDC
MPCD3
MPCD3
MPCD3
MPCD3
MDC0
or
MDC1
MPCD0
MPCD1
MPCD2
ÒÒ
ÒÒ
ÒÒ
ÒÒ
0000h
8000h
FFFFh
Data Memory
Program Memory
ÒÒ
: reserved
NOTES: A. MPDC: local program/data memory in subsystem C
B. MDC: local data memory in subsystem C. MDC is controlled by the data memory map register (DMMR).
DMMR=0, MDC0 is mapped in 8000h – FFFFh.
DMMR=1, MDC1 is mapped in 8000h – FFFFh.
C. MPCD: shared program memory in subsystems C and D
Figure 3–5. Subsystem C CPU Memory Map
16
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Memory Map with OVLY = 1
Page 0
Page 1
Page 2
Page 3
MPDD
MPDD
MPDD
MPDD
MPDD
MDD0
or
MDD1
MPCD0
MPCD1
MPCD2
MPCD3
0000h
8000h
FFFFh
Data Memory
Program Memory
Memory Map with OVLY = 0
Page 0
Page 1
Page 2
Page 3
MPDD
MPCD3
MPCD3
MPCD3
MPCD3
MDD0
or
MDD1
MPCD0
MPCD1
MPCD2
0000h
8000h
FFFFh
Data Memory
ÕÕ
ÕÕ
ÒÒ
ÒÒ
ÒÒ
ÒÒ
Program Memory
reserved
NOTES: A. MPDD: local program/data memory in subsystem D
B. MDD: local data memory in subsystem D. MDD is controlled by the data memory map register (DMMR).
DMMR=0, MDD0 is mapped in 8000h – FFFFh.
DMMR=1, MDD1 is mapped in 8000h – FFFFh.
C. MPCD: shared program memory in subsystems C and D
Figure 3–6. Subsystem D CPU Memory Map
Figure 3–7 shows the CPU data memory map. The lower 32K-word data memory location in all pages is the
overlay area. Program memory has overlay area over the lower 32K words on all pages as well.
The overlay areas refer to:
1. When OVLY = 1, the lower 32K words of data space are mapped to the lower 32K words of all program
pages in the memory map.
2. When OVLY = 0, the lower 32K words of data space are mapped only to the lower 32K words of data space
and the lower 32K words of program page 3 are mapped to the lower 32K words of all program pages.
December 1999 – Revised April 2002
SPRS122E
17
Functional Overview
Hex
00 0000
MemoryMapped
Registers
00 005F
00 0060
DARAM0
16K Words
00 3FFF
00 4000
DARAM1
16K Words
00 7FFF
00 8000
DARAM2
(DMMR=0)
16K Words
DARAM4
(DMMR=1)
00 BFFF
00 C000
DARAM3
(DMMR=0)
16K Words
DARAM5
(DMMR=1)
00 FFFF
Data Memory
NOTE: The upper part of data memory is controlled by the Data Memory Map Register (DMMR).
1. DMMR=0, DARAM2 and DARAM3 are mapped in 8000h – FFFFh.
2. DMMR=1, DARAM4 and DARAM5 are mapped in 8000h – FFFFh.
Figure 3–7. Detailed Memory Map of Local Data Memory Relative to CPU Subsystems A, B, C, and D
3.1.2 On-Chip Dual-Access RAM (DARAM)
Each 5441 subsystem has 96K 16-bit words of on-chip DARAM (six blocks of 16K words). Each of these
DARAM blocks can be accessed twice per machine cycle. This memory is intended primarily to store data
values; however, it can be used to store program as well. At reset, the DARAM is mapped into data memory
space (OVLY=0). The lower part of DARAM (0000h–8000h) can be mapped into program/data memory space
by setting the OVLY bit in the processor-mode status (PMST) register of the TMS320C54x cLEAD CPU in
each DSP subsystem.
3.1.3 On-Chip Two-Way Shared RAM
There are 128K 16-bit words of on-chip RAM (four blocks of 32K words) that are shared between subsystems
A and B. There are 128K 16-bit words of on-chip RAM (four blocks of 32K words) that are shared between
subsystems C and D. This memory is intended to store program only. Both subsystems are able to make one
instruction fetch from any location in the two-way shared memory each cycle simultaneously. No subsystem
CPU can write to the shared memory as only the DMA can write to shared memory.
If any of the CPU program fetches are requested at the same time as an M-bus transfer request, the CPU is
stalled until all M bus transfers are completed. In other words, any read or write requested by the M bus (driven
by DMA controller or HPI) has priority over the CPUs’ (A, B, C, and D) program fetches. The M-bus reads or
writes always take two cycles to complete.
18
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.1.4 Extended Data Memory
The data memory space of each 5441 subsystem addresses 128K 16-bit words. There are two pages of data
memory location with each page consisting of 64K words. The 5441 device uses a data memory map register
(DMMR) to facilitate extended data memory access. The DMMR is a peripheral memory-mapped register. The
contents of the DMMR register, once being written with an extended data number by the DSP CPU, will be
associated with the address decoding for all the data memory CPU accesses.
3.1.5 Extended Program Memory
The 5441 device uses a paged extended memory scheme in program space to allow access to 256K 16-bit
words. This extended program memory (each subsystem) is organized into four pages (0–3), pages 0–3 are
two-way shared memory. Each page is 64K words in length. The program counter extension register (XPC)
defines the program page selection. To implement the extended program memory scheme, the 5441 device
includes the following feature:
•
Two C54x instructions allow each subsystem CPU access to the on-chip program memory.
–
–
READA – Read program memory addressed by accumulator A and store in data memory
WRITA – Write data to program memory addressed by accumulator A
(Writes not allowed for CPUs to shared program memory)
3.1.6 Program Memory
The program memory is accessible on multiple pages, depending on the XPC value. Within these pages,
memory is accessible depending on the address range.
•
Access in the lower 32K words of each page is dependent on the state of OVLY.
–
–
•
OVLY = 0 – Program memory is accessed from program memory page 3 for all values of XPC.
OVLY = 1 – Program memory is accessed from local data/program DARAM for all values of XPC.
Access in the upper 32K words of each page is dependent on the state of OVLY.
–
–
OVLY = 0 – All pages of program memory except page 3 (which is reserved) are accessible for all
values of XPC.
OVLY = 1 – All pages of program memory are accessible for all values of XPC.
3.1.7 Data Memory
Accesses on extended data spaces are dependent on the value of the data memory map register (DMMR).
Within the page, memory is accessible depending on the address range.
•
Access in the lower 32K words
–
•
Data memory is accessed from local data/program DARAM for all values of DMMR.
Access in the upper 32K words
–
Which data memory block is accessed depends on the value of DMMR.
–
There are four 16K-word DARAM blocks for the upper addresses (8000h – FFFFh)
DMMR=0: DARAM2 and DARAM3 are mapped to the upper addresses
DMMR=1: DARAM4 and DARAM5 are mapped to the upper addresses
3.1.8 I/O Memory
The 5441 does not support I/O memory accesses.
C54x is a trademark of Texas Instruments.
December 1999 – Revised April 2002
SPRS122E
19
Functional Overview
3.1.9 Multicore Reset Signals
The 5441 device includes five reset signals: A_RS, B_RS, C_RS, D_RS, and RESET. The A_RS, B_RS,
C_RS, and D_RS local reset signals function as the CPU reset signal for subsystem A, B, C, and D,
respectively. The RESET services as a global reset for the whole device.
The global reset (RESET) is a superset of local resets A_RS, B_RS, C_RS, and D_RS. The assertion of
RESET triggers all the local resets; however, none of the local resets triggers the global reset. The local reset
signals reset the state of the CPU registers and CPU memory-mapped peripheral registers, and upon release,
initiate the reset function. The global reset, RESET, resets the on-chip PLL and clears the watchdog timer flag
(WDFLAG) bit. The local reset signals are not able to reset the PLL or clear the WDFLAG.
The global reset (RESET) and local resets (x_RS) clears the program counter extension register (XPC) to zero
while the RESET instruction does not affect the XPC.
3.1.10
Device Bootload
The 5441 device supports an HPI boot sequence, which is used to download code while the DSP is in reset.
The external master holds the device in reset while it loads code to the on-chip memory of each subsystem,
subsystem selection is made by HPI_SEL1 and HPI_SEL2 signals. The host can release the 5441 from reset
by using either of the following methods.
3.2
•
If the x_RS (x = A, B, C, or D for subsystem A, B, C, or D, respectively) pins are held low while RESET
transitions from low to high, the reset of each subsystem will be controlled by the x_RS pins. When the
host has finished downloading code, it can drive x_RS high to release the cores from reset.
•
If the x_RS pins are held high while RESET transitions from low to high, the subsystems will stay in reset
until an HPI data write to address 0x2F occurs. This means the host can download code to subsystem
x and then release core x from reset by writing any data to core x’s address 0x2F via the HPI. The host
can then repeat the sequence for other cores. This mode allows the host to control 5441 reset without
additional hardware.
On-Chip Peripherals
All the C54x devices have the same CPU structure; however, they have different on-chip peripherals
connected to their CPUs. The on-chip peripheral options provided are:
•
•
•
•
•
•
•
DMA controller
16-bit host-port interface I/O ports
Multichannel buffered serial ports (McBSPs)
A hardware timer
A hardware watchdog timer
A software-programmable clock generator using a phase-locked loop (PLL)
General-purpose I/O
3.2.1 Direct Memory Access (DMA) Controller
The 5441 includes four 6-channel direct memory access (DMA) controllers for performing data transfers
independent of the CPU, one controller for each subsystem. The primary function of the 5441 DMA controller
is to provide code overlays and to manage data transfers between on-chip memory, the peripherals, and
off-chip host.
In the background of CPU operation, the 5441 DMA allows movement of data between internal program/data
memory and internal peripherals, such as the McBSPs and the HPI. Each subsystem has its own independent
DMA with six programmable channels, which allows for six different contexts for DMA operation. The HPI has
a dedicated auxiliary DMA channel. The remapped areas represent address aliasing for DMA accesses within
each subsystem. Figure 3–8 through Figure 3–11 illustrate the local DMA memory map of each subsystem.
20
SPRS122E
December 1999 – Revised April 2002
Functional Overview
ÇÇ
ÇÇ
ÒÒ
ÒÒ
Page 0
Page 1
Page 0
Page 1
Page 2
Page 3
MPDA
MPDA
MPDA
MPDA
MPDA
MDA1
MPAB0
MPAB1
MPAB0
MPAB1
0000h
0020h
0060h
MPDA
8000h
MDA0
FFFFh
ÇÇ
ÇÇ
ÒÒ
ÒÒ
Data Memory
Reserved
Program Memory
McBSP DXR/DRR MMRegs only
: Remapped areas
NOTES: A. MPDA: local program/data memory in subsystem A
B. MDA: local data memory in subsystem A
C. MPAB: two-way shared program memory in subsystems A and B
Figure 3–8. Subsystem A Local DMA Memory Map
ÇÇ
ÇÇ
ÒÒ
ÒÒ
Page 0
Page 1
Page 0
Page 1
Page 2
Page 3
MPDB
MPDB
MPDB
MPDB
MPDB
MDB1
MPAB2
MPAB3
MPAB2
MPAB3
0000h
0020h
0060h
MPDB
8000h
MDB0
FFFFh
Ç
ÕÕ
Data Memory
Reserved
Program Memory
McBSP DXR/DRR MMRegs only
: Remapped areas
NOTES: A. MPDB: local program/data memory in subsystem B
B. MDB: local data memory in subsystem B
C. MPAB: two-way shared program memory in subsystems A and B
Figure 3–9. Subsystem B Local DMA Memory Map
December 1999 – Revised April 2002
SPRS122E
21
Functional Overview
ÇÇ
ÇÇ
ÒÒ
ÒÒ
Page 0
Page 1
Page 0
Page 1
Page 2
Page 3
MPDC
MPDC
MPDC
MPDC
MPDC
MDC1
MPCD0
MPCD1
MPCD0
MPCD1
0000h
0020h
0060h
MPDC
8000h
MDC0
FFFFh
ÇÇ
ÇÇ
ÕÕ
ÕÕ
Data Memory
Reserved
Program Memory
McBSP DXR/DRR MMRegs only
: Remapped areas
NOTES: A. MPDC: local program/data memory in subsystem C
B. MDC: local data memory in subsystem C
C. MPCD: two-way shared program memory in subsystems C and D
Figure 3–10. Subsystem C Local DMA Memory Map
ÇÇ
ÇÇ
ÒÒ
ÒÒ
Page 0
0000h
0020h
0060h
MPDD
8000h
MDD0
Page 1
Page 0
Page 1
Page 2
Page 3
MPDD
MPDD
MPDD
MPDD
MPDD
MPCD2
MPCD3
MPCD2
MPCD3
MDD1
FFFFh
ÇÇ
Õ
Data Memory
Reserved
Program Memory
McBSP DXR/DRR MMRegs only
: Remapped areas
NOTES: A. MPDD: local program/data memory in subsystem D
B. MDD: local data memory in subsystem D
C. MPCD: two-way shared program memory in subsystems C and D
Figure 3–11. Subsystem D Local DMA Memory Map
22
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.2.1.1
DMA Controller Features
The 5441 DMA has the following features:
•
•
•
•
•
•
•
•
•
•
The DMA operates independently of the CPU.
The DMA has six channels. The DMA can keep track of the contexts of six independent block transfers.
The DMA has higher priority than the CPU.
Each channel has independently programmable priority.
Each channel’s source and destination address registers include configurable indexing modes. The
address can be held constant, postincremented, postdecremented, or adjusted by a programmable value.
Each read or write transfer can be initialized by selected events.
The DMA supports single-word (16-bit) and double-word (32-bit) transfers.
Each DMA channel has independent reload registers.
Each DMA channel has independent extended source/destination data page registers.
The DMA does not support I/O memory access.
A 16-bit DMA transfer requires four CPU clock cycles to complete—two cycles for reads and two cycles for
writes. Since the DMA controller shares the DMA bus with the HPI module, the DMA access rate is reduced
when the HPI is active.
3.2.1.2
DMA Reload Registers
Each DMA channel has its own reload registers which are utilized when autoinitialization is enabled for the
current DMA channel. The reload registers include:
•
•
•
•
Source address reload register (DMGSAn)
Destination address reload register (DMGDAn)
Element count reload register (DMGCRn)
Frame count reload register (DMGFRn)
The “n” in the register names refers to DMA channel number: 0, 1, 2, 3, 4, and 5.
In the DMPREC register, bit 14 (IAUTO) is used to enable individual reload register for each channel. If that
bit is not set, the channel 0 reload register will be loaded to all chanels (this is backward compatible).
3.2.1.3
Extended Source/Destination Data Page Registers (DMSRCDPn/DMDSTDPn)
The DMA controller has the ability to perform transfers to and from the extended data memory space. The
DMA extended source data page register and extended destination data page register service this purpose
and only the least significant seven bits are used to designate the extended data memory page. Each of the
DMA channels will have one set of these registers for extended data memory page (other than page 0) access.
Data memory space transfers cannot cross 64K page boundaries. If a data page boundary is crossed during
a transfer, the next transfer will wrap on to the same page.
For detailed information on DMA registers, see TMS320C54x DSP Reference Set, Volume 5: Enhanced
Peripherals (literature number SPRU302).
3.2.1.4
DMA Controller Synchronization Events
The transfers associated with each DMA channel can be synchronized to one of several events. The DSYN
bit field of the DMA channel x sync select and frame count (DMSFCx) register selects the synchronization
event for a channel. The list of possible events and the DSYN values are shown in Table 3–1.
December 1999 – Revised April 2002
SPRS122E
23
Functional Overview
Table 3–1. DMA Synchronization Events
DSYN VALUE
DMA SYNCHRONIZATION EVENT
0000b
No synchronization used
0001b
McBSP0 Receive Event
0010b
McBSP0 Transmit Event
0011b
McBSP2 Receive Event
0100b
McBSP2 Transmit Event
0101b
McBSP1 Receive Event
0110b
McBSP1 Transmit Event
0111b – 1111b
3.2.1.5
Reserved
DMA Channel Interrupt Selection
The DMA controller can generate a CPU interrupt for each of the six channels. However, channels 0, 1, 2,
and 3 are multiplexed with other interrupt sources. DMA channels 0 and 1 share an interrupt line with the
receive and transmit portions of McBSP2 (IMR/IFR bits 6 and 7), and DMA channels 2 and 3 share an interrupt
line with the receive and transmit portions of McBSP1 (IMR/IFR bits 10 and 11). When the 5441 is reset, the
interrupts from these four DMA channels are deselected. The INTSEL bit field in the DMA channel priority and
enable control (DMPREC) register can be used to select these interrupts, as shown in Table 3–2.
Table 3–2. DMA Channel Interrupt Selection
INTSEL Value
IMR/IFR[6]
IMR/IFR[7]
IMR/IFR[10]
IMR/IFR[11]
00b (reset)
BRINT2
BXINT2
BRINT1
BXINT1
01b
BRINT2
BXINT2
DMAC2
DMAC3
10b
DMAC0
DMAC1
DMAC2
DMAC3
11b
Reserved
3.2.2 16-Bit Bidirectional Host-Port Interface (HPI16)
3.2.2.1
HPI16 Memory Map
The HPI16 is an enhanced 16-bit version of the C54x DSP 8-bit host-port interface (HPI). The HPI16 is
designed to allow a 16-bit host to access the DSP on-chip memory, with the host acting as the master of the
interface. Each HPI subsystem memory map is identical to its corresponding DMA memory map except the
HPI memory map does not support accesses to any memory-mapped registers.
Some of the features of the HPI16 include:
•
•
•
•
•
•
•
•
•
•
24
A 16-bit bidirectional data bus
Multiple data strobes and control signals to allow glueless interfacing to a variety of hosts
Multiplexed and nonmultiplexed address/data modes
A 19-bit address bus used in nonmultiplexed mode to allow access to all on-chip (including extended
address pages) memory
A 19-bit address register used in multiplexed mode. Includes address autoincrement feature for faster
accesses to sequential addresses
Interface to on-chip DMA module to allow access to entire on-chip memory space
HRDY signal to hold off host accesses due to DMA latency
Control register available in multiplexed mode only. Accessible by either host or DSP to provide host/DSP
interrupts, extended addressing, and data prefetch capability
HPI_SEL1 and HPI_SEL2 pins are used to make selection among the four subsystem HPI modules.
Both the HPI data bus and address bus have bus-holder features. The bus holders can be
enabled/disabled by the CPUs.
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.2.2.2
HPI Multiplexed Mode
In multiplexed mode, HPI16 operation is very similar to that of the standard 8-bit HPI, which is available with
other C54x DSP products. A host with a multiplexed address/data bus can access the HPI16 data register
(HPID), address register (HPIA), or control register (HPIC) via the HD bidirectional data bus. The host initiates
the access with the strobe signals (HDS1, HDS2, HCS) and controls the type of access with the HCNTL,
HR/W, and HAS signals. The DSP can interrupt the host via the x_HINT signal, and can stall host accesses
via the HRDY signal. Bit 20 of the HPIA register is used to make selection between program (shared) memory
and data (local) memory access. Table 3–3 shows the memory selection via HA[20].
Table 3–3. HPI Local/Shared Memory Selection Via HA[20]
Memory Type
HA[20]
3.2.2.3
0
Local (data)
1
Shared (program)
Host/DSP Interrupts
In multiplexed mode, the HPI16 offers the capability for the host and DSP to interrupt each other through the
HPIC register.
For host-to-DSP interrupts, the host must write a “1” to the DSPINT bit of the HPIC register. This generates
an interrupt to the DSP. This interrupt can also be used to wake the DSP from any of the IDLE 1,2, or 3 states.
Note that the DSPINT bit is always read as “0” by both the host and DSP. The DSP cannot write to this bit (see
Figure 3–12).
For DSP-to-host interrupts, the DSP must write a “1” to the HINT bit of the HPIC register to interrupt the host
via the x_HINT pin. The host acknowledges and clears this interrupt by also writing a “1” to the HINT bit of the
HPIC register. Note that writing a “0” to the HINT bit by either host or DSP has no effect.
December 1999 – Revised April 2002
SPRS122E
25
Functional Overview
3.2.2.4
HPI Nonmultiplexed Mode
In nonmultiplexed mode, a host with separate address/data buses can access the HPI16 data register (HPID)
via the 16-bit HD bidirectional data bus, and the address register (HPIA) via the 19-bit HA address bus. The
HA[18] signal is used to make selection between program (shared) memory and data (local) memory access.
Table 3–4 shows the memory selection via HA[18].
Table 3–4. HPI Local/Shared Memory Selection Via HA[18]
Memory Type
HA[18]
0
Local (data)
1
Shared (program)
The host initiates the access with the strobe signals (HDS1, HDS2, and HCS) and controls the direction of
the access with the HR/W signal. The HPI16 can stall host accesses via the HRDY signal. Note that the HPIC
register is not available in nonmultiplexed mode since there are no HCNTL signals available. All host accesses
initiate a DMA read or write access. Figure 3–12 shows a block diagram of the HPI16 in nonmultiplexed mode.
HD[15:0]
Data[15:0]
HPID[15:0]
Address[n:0]†
HA[n :0]†
R/W
Data strobes
Ready
HRDY
HR/W
HDS1, HDS2, HCS
DMA
Internal
memory
HPI-16
HOST
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
C54x
CPU
† n = 0 to 18
Figure 3–12. Interfacing to the HPI-16 in Non-Multiplexed Mode
26
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.2.2.5
HPI Bus Holder Control
Both the HPI data and address buses have bus holders. By default, the bus holders are disabled after global
reset or subsystem A reset. The bus holders are configured via the BHD and BHA bits in the bank switching
control register (BSCR) located at 29h in subsystem A. Figure 3–13 shows the BSCR bit layout for
subsystem A and Table 3–5 describes the bit functions of BSCR.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Reserved
BHD
BHA
Reserved
U
R/W+0
R/W+0
U
LEGEND: R = Read, W = Write, U = Undefined
Figure 3–13. BSCR Register Bit Layout for Subsystem A
Table 3–5. BSCR Register Bit Functions for Subsystem A
BIT
NO.
BIT
NAME
15–3
Reserved
2
BHD
Data bus holder. BHD is cleared to 0 at reset.
BHD = 0: The HPI data bus holder is disabled.
BHD = 1: The HPI data bus holder is enabled.
1
BHA
Address bus holder. BHA is cleared to 0 at reset.
BHA = 0: The HPI address bus holder is disabled.
BHA = 1: The HPI address bus holder is enabled.
0
Reserved
3.2.2.6
FUNCTION
These bits are reserved and are read as 0.
This bit is reserved and is read as 0.
Other HPI16 System Considerations
•
Operation During IDLE – The HPI16 can continue to operate during IDLE1 or IDLE2 by using special clock
management logic that turns on relevant clocks to perform a synchronous memory access, and then turns
the clocks back off to save power. The DSP CPU does not wake up from the IDLE mode during this
process.
•
Downloading Code During Reset – The HPI16 can download code while the DSP is in reset. The system
provides a pin (RESET) that provides a way to take the HPI16 module out of reset while leaving the DSP
in reset.
•
Emulation considerations – The HPI16 can continue operation even when the DSP CPU is halted due to
debugger breakpoints or other emulation events.
•
XA Multiplexer – XA multiplexer controls the HPI data traffic from each subsystem to the device boundary.
The HPI module is the slave on the HPI bus. Figure 3–14 shows the 5441 block diagram with XA logic.
The XA basic function includes:
•
–
Making the HPI bus available for the selected subsystem HPI module according to HPI selection pins
HPI_SEL1/HPI_SEL2.
–
Granting HPI path to one of the subsystems at one time
The HPI_SEL1 and HPI_SEL2 pins are used to select the HPI module among the four cores. The selection
is indicated in Table 3–6.
December 1999 – Revised April 2002
SPRS122E
27
Functional Overview
DSP Subsystem A
DSP ID: 0000
HPI Bus
HPI_SEL1
HPI_SEL2
DSP Subsystem B
DSP ID: 0001
HPI Bus
XA
DSP Subsystem C
DSP ID: 0010
HPI Bus
DSP Subsystem D
DSP ID: 0011
HPI Bus
NOTE: XA is the MUXing logic for HPI access.
Figure 3–14. XA Multiplexer for HPI Access
Table 3–6. HPI Module Selection
28
SPRS122E
HPI_SEL2
HPI_SEL1
SELECTED HPI MODULE
0
0
Subsystem A
0
1
Subsystem B
1
0
Subsystem C
1
1
Subsystem D
December 1999 – Revised April 2002
Functional Overview
3.2.3 Multichannel Buffered Serial Port (McBSP)
The 5441 device provides high-speed, full-duplex serial ports that allow direct interface to other C54x/LC54x
devices, codecs, and other devices in a system. There are twelve multichannel buffered serial ports (McBSPs)
on chip (three per subsystem).
The McBSP provides:
•
•
•
Full-duplex communication
Double-buffer data registers, which allow a continuous data stream
Independent framing and clocking for receive and transmit
In addition, the McBSP has the following capabilities:
•
Direct interface to:
•
•
•
•
•
–
T1/E1 framers
–
MVIP switching-compatible and ST-BUS compliant devices
–
IOM-2 compliant device
–
AC97-compliant device
–
Serial peripheral interface (SPI)
Multichannel transmit and receive of up to 128 channels
A wide selection of data sizes, including: 8, 12, 16, 20, 24, or 32 bits
µ-law and A-law companding
Programmable polarity for both frame synchronization and data clocks
Programmable internal clock and frame generation
3.2.3.1
McBSP Clock Source
The 5441 McBSPs allow either the receive clock pin (BCLKRn) or the transmit clock pin (BCLKXn) to be
configured as the input clock to the sample rate generator. This enhancement is enabled through two register
bits: bit 7 [the enhanced sample clock mode bit (SCLKME)] of the pin control register (PCR), and bit 13 [the
McBSP sample rate generator clock mode bit (CLKSM)] of the sample rate generator register 2 (SRGR2).
SCLKME is an addition to the PCR contained in the McBSPs on previous TMS320C5000 DSP platform
devices. The new bit layout of the PCR is shown in Figure 3–15. For a description of the remaining bits, see
TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals (literature number SPRU302).
15
14
13
12
11
10
9
8
Reserved
XIOEN
RIOEN
FSXM
FSRM
CLKXM
CLKRM
R,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
7
6
5
4
3
2
1
0
SCLKME
CLKS_STAT
DX_STAT
DR_STAT
FSXP
FSRP
CLKXP
CLKRP
RW,+0
R,+0
R,+0
R,+0
RW,+0
RW,+0
RW,+0
RW,+0
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–15. Pin Control Register (PCR)
TMS320C5000 is a trademark of Texas Instruments.
December 1999 – Revised April 2002
SPRS122E
29
Functional Overview
The selection of the sample rate generator (SRG) clock input source is made by the combination of the CLKSM
and SCLKME bit values as shown in Table 3–7.
Table 3–7. Sample Rate Generator Clock Source Selection
SRG Clock Source
SCLKME
CLKSM
0
0
Reserved
0
1
CPU clock
1
0
BCLKRn pin
1
1
BCLKXn pin
When either of the bidirectional pins, BCLKRn or BCLKXn, is configured as the clock input, its output buffer
is automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKRn pin is configured as
the SRG input. In this case, both the transmitter and receiver circuits can be synchronized to the SRG output
by setting PCR[9:8] for CLKXM = 1 and CLKRM = 1. However, the SRG output is only driven onto the BCLKXn
pin because the BCLKR output is automatically disabled.
3.2.3.2
Multichannel Selection
The McBSP supports independent selection of multiple channels for the transmitter and receiver. When
multiple channels are selected, each frame represents a time-division multiplexed (TDM) data stream. In using
time-division multiplexed data streams, the CPU may only need to process a few of them. Thus, to save
memory and bus bandwidth, multichannel selection allows independent enabling of particular channels for
transmission and reception. Up to a maximum of 128 channels in a bit stream can be enabled or disabled.
The 5441 McBSPs have two working modes that are selected by setting the RMCME and XMCME bits in the
multichannel control registers MCR1x and MCR2x, respectively (see Figure 3–16 and Figure 3–17). For a
description of the remaining bits, see TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals
(literature number SPRU302).
•
15
14
In the first mode, when RMCME = 0 and XMCME = 0, there are two partitions (A and B), with each
containing 16 channels as shown in Figure 3–16 and Figure 3–17. This is compatible with the McBSPs
used in the 5420, where only 32-channel selection is enabled (default).
13
12
11
10
9
8
XMC
Reserved
ME
R,+0
RW,+0
7
6
5
4
3
2
1
0
XPBBLK
XPABLK
XCBLK
XMCM
RW,+0
RW,+0
R,+0
RW,+0
LEGEND: R = Read, W = Write, +0 = Value at reset; x = McBSP 0,1, or 2
Figure 3–16. Multichannel Control Register 2 for McBSPx (MCR2x)
15
14
13
12
Reserved
R,+0
11
10
9
RMC
ME
RW,+0
8
7
6
5
4
3
2
1
0
RPBBLK
RPABLK
RCBLK
RMCM
RW,+0
RW,+0
R,+0
RW,+0
LEGEND: R = Read, W = Write, +0 = Value at reset; x = McBSP 0,1, or 2
Figure 3–17. Multichannel Control Register 1 for McBSPx (MCR1x)
30
SPRS122E
December 1999 – Revised April 2002
Functional Overview
•
In the second mode, with RMCME = 1 and XMCME = 1, the McBSPs have 128-channel selection
capability. Twelve registers (RCERCx–RCERHx and XCERCx–XCERHx) are used to enable the
128-channel selection. The subaddresses of the registers are shown in Table 3–24. These registers,
functionally equivalent to the RCERA0–RCERB1 and XCERA0–XCERB1 registers, are used to
enable/disable the transmit and receive of additional channel partitions (C,D,E,F,G, and H) in the
128-channel stream. For example, XCERH1 is the transmit enable for channel partition H (channels 112
to 127) of McBSP1 for each DSP subsystem. See Figure 3–18, Table 3–8, Figure 3–19, and Table 3–9
for bit layouts and functions of the receive and transmit registers.
15
14
13
12
11
10
9
8
RCERyz15
RCERyz14
RCERyz13
RCERyz12
RCERyz11
RCERyz10
RCERyz9
RCERyz8
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
7
6
5
4
3
2
1
0
RCERyz7
RCERyz6
RCERyz5
RCERy4
RCERyz3
RCERyz2
RCERyz1
RCERyz0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
LEGEND: R = Read, W = Write, +0 = Value at reset; y = Partition A,B,C,D,E,F,G, or H; z = McBSP 0,1, or 2
Figure 3–18. Receive Channel Enable Registers Bit Layout for Partitions A to H
Table 3–8. Receive Channel Enable Registers for Partitions A to H
Bit
15–0
Note:
Name
Function
RCERyz[15:0]
Receive Channel Enable Register
RCERyz n = 0
Disables reception of nth channel in partition y.
RCERyz n = 1
Enables reception of nth channel in partition y.
y = Partition A,B,C,D,E,F,G, or H; z = McBSP 0,1, or 2; n = bit 15–0
15
14
13
12
11
10
9
8
XCERyz15
XCERyz14
XCERyz13
XCERyz12
XCERyz11
XCERyz10
XCERyz9
XCERyz8
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
7
6
5
4
3
2
1
0
XCERyz7
XCERyz6
XCERyz5
XCERy4
XCERyz3
XCERyz2
XCERyz1
XCERyz0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
RW,+0
LEGEND: R = Read, W = Write, +0 = Value at reset; y = Partition A,B,C,D,E,F,G, or H; z = McBSP 0,1, or 2
Figure 3–19. Transmit Channel Enable Registers Bit Layout for Partitions A to H
Table 3–9. Transmit Channel Enable Registers for Partitions A to H
Bit
15–0
Name
Function
XCERyz[15:0]
Transmit Channel Enable Register
XCERyz n = 0
Disables transmit of nth channel in partition y.
XCERyz n = 1
Enables transmit of nth channel in partition y.
LEGEND: y = Partition A,B,C,D,E,F,G, or H; z = McBSP 0,1, or 2; n = bit 15–0
December 1999 – Revised April 2002
SPRS122E
31
Functional Overview
The McBSP is fully static and operates at arbitrarily low clock frequencies. For the maximum McBSP
multichannel operating frequency, see Section 5.10 of this data manual.
3.2.3.3
McBSP1 and McBSP2
The four McBSP1s from each subsystem share the same external signal pins. The four McBSP2s from each
subsystem share the same set of external signal pins. They can only operate in either of the following modes:
•
multichannel mode (x_BCLKR, x_BCLKX, x_BFSR, and x_BFSX are external and the McBSPs share
TDM stream with no single time slot assigned to more than one McBSP)
•
standard serial port mode (x_BCLKR, x_BCLKX, x_BFSR, and x_BFSX are external and only one McBSP
is enabled at one time).
For McBSP1 and McBSP2, no other mode is supported.
3.2.3.4
SA Multiplexer
The SA1 and SA2 multiplexers provide multiplexing for the four McBSP1s and the four McBSP2s from each
subsystem and present the data path to the device boundary. All the same functional pins from the four
McBSP1s are multiplexed together by SA1 and connect to the device external pins. All the same functional
pins from the four McBSP2s are multiplexed together by SA2 and connect to the device external pins. The
functional pins are: data receive (BDRn), data transmit (BDXn), receive frame sync (BFSRn), transmit frame
sync (BFSXn), receive shift clock (BCLKRn), and transmit shift clock (BCLKXn).
When McBSP operates in multichannel mode, software shall ensure that the same channel (time slot) not be
assigned by more than one subsystem. If more than one subsystem enables the same transmit time slot, the
results are undefined.
Figure 3–20 shows 5441 block diagram with SA1 logic; SA2 logic is identical.
DSP Subsystem A
DSP ID: 0000
DSP Subsystem B
DSP ID: 0001
DSP Subsystem C
DSP ID: 0010
DSP Subsystem D
DSP ID: 0011
McBSP1
McBSP1
McBSP1
McBSP1
BCLKR1
BCLKX1
BFSR1
BFSX1
BDR1
BDX1
SA1
NOTE: SA is the MUX/Arbitration logic for McBSP1 operation.
Figure 3–20. SA Multiplexer for McBSP1 Operation
32
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.2.4 Hardware Timer
Each 5441 subsystem has one independent software programmable timer. The memory-mapped registers
control the operation of the timer. The timer resolution is the clock rate of the CPU. The timer output shares
the pin with GPIO3 and is controlled by GPIO register bit 15.
The timer supports a 32-bit dynamic range. The timer consists of a programmable 16-bit main counter and
a programmable prescalar. The main counter is driven by the prescalar, which decrements by one at every
CPU clock. Once the prescalar reaches zero, the 16-bit counter decrements by one. When the 16-bit counter
decrements to zero, a maskable interrupt (TINT) is generated and the timer output pin (TOUT) asserts an
active-high pulse (2H – 2 ns, H = 0.5 clock cycle). The timer output pulse is driven on GPIO3 when the TOUT
bit is set to high in the GPIO register. When the timer is configured in continuous mode, the timer counter and
prescalar will be reloaded accordingly after the timer counter exhausts. The timer can be stopped, restarted,
reset, or disabled via the bits of the timer control register.
There are four 16-bit registers associated with the timer.
•
•
•
•
3.2.4.1
Timer counter register (TIM)
Timer period register (PRD)
Timer control register (TCR)
Timer second control register (TSCR)
TIM Register
This register is loaded with the period register (PRD) value and decrements once the PRD value is loaded.
3.2.4.2
PRD Register
This register is used to reload the timer counter register (TIM).
3.2.4.3
TCR Register
This register provides the control and status information. TCR bit fields are shown in Figure 3–21 and
described in Table 3–10.
15
14
13
Reserved
12
11
10
SOFT
FREE
R/W+0
R/W+0
9
8
7
6
5
4
3
2
1
PSC
TRB
TSS
TDDR
R/W+0
R/W+0
R/W+0
R/W+0
0
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–21. Timer Control Register (TCR)
December 1999 – Revised April 2002
SPRS122E
33
Functional Overview
Table 3–10. TCR Bit Description
BIT
NO.
BIT
NAME
15–12
Reserved
FUNCTION
Register bit is reserved. Read 0, write has no effect.
Used in conjunction with the FREE bit to determine the state of the timer when a breakpoint is encountered in
the HLL debugger.
11
SOFT
When FREE = 0 and SOFT = 0 the timer stops immediately.
When FREE = 0 and SOFT = 1, the timer stops when the counter decrements to 0.
Used in conjunction with the SOFT bit to determine the state of the timer when a breakpoint is encountered in
the HLL debugger.
10
FREE
When FREE = 0, the SOFT bit selects the timer mode.
When FREE = 1, the timer runs free regardless of the SOFT bit.
9–6
PSC
Timer prescalar counter, used only when PREMD = 0 (in TSCR register) and the prescaler is in direct mode.
5
TRB
Timer reload. When TRB is set, TIM is loaded with the value in the PRD register and the PSC field is loaded with
the value in the TDDR field (when prescalar is in direct mode). TRB is always read a 0.
Timer stop status.
4
TSS
Stops or starts the timer at reset. TSS is cleared and the timer starts timing.
0 = timer is started
1 = timer is stopped
Timer prescalar.
Case 1: When PREMD = 0, TDDR is a 4-bit reload prescalar. When PSC decrements to 0, PSC is loaded with
the contents of TDDR.
Case 2: When PREMD = 1,TDDR is an indirect prescalar, the contents in TDDR is used to specify the timer
prescalar.
3–0
34
SPRS122E
TDDR
TDDR[3:0]
PRESCALAR
0000
0001h
0001
0003h
0010
0007h
0011
000Fh
0100
001Fh
0101
003Fh
0110
007Fh
0111
00FFh
1000
01FFh
1001
03FFh
1010
07FFh
1011
0FFFh
1100
1FFFh
1101
3FFFh
1110
7FFFh
1111
FFFFh
December 1999 – Revised April 2002
Functional Overview
3.2.4.4
TSCR Register
This 16-bit register contains bits to set prescalar mode.
15
14
13
Reserved
12
11
10
9
8
7
PREMD
6
5
4
3
2
1
0
Reserved
R/W+0
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–22. Timer Second Control Register (TSCR)
Table 3–11. TSCR Bit Description
BIT
NO.
BIT
NAME
15–13
Reserved
FUNCTION
Register bit is reserved. Read 0, write has no effect.
Prescalar mode select bit.
12
PREMD
11–0
Reserved
0 = direct mode, TDDR is a 4-bit reload prescalar (default value after reset).
1 = indirect mode, TDDR is used to select individual prescalar value.
Register bit is reserved. Read 0, write has no effect.
Out of reset, the TIM and PRD registers are set to a maximum value of FFFFh, the PREMD bit (TSCR[12])
is set to 0, the TDDR field (TCR[3:0]) is cleared to 0, and the timer is started.
3.2.5 Watchdog Timer
Each subsystem contains a watchdog timer. The purpose of the watchdog timer is to prevent the system from
lock in case the software becomes trapped in loops with no controlled exit. The watchdog timer has a
“watchdog output” pin associated with it. This watchdog output pin is shared with the x_GPIO2/x_WTOUT pin;
once the watchdog timer is enabled, this pin is automatically configured as x_WTOUT. The watchdog timer
requires a special service sequence to be executed periodically. Without this periodic servicing, the watchdog
timer counter reaches zero and times out. Consequently, an active-low pulse will be asserted on the “watchdog
output” pin and an internal maskable interrupt will be triggered. The watchdog output (x_WTOUT) pin can be
gluelessly external-connected to the local hardware reset or NMI (nonmaskable interrupt). This allows
maximum flexibility in utilizing the watchdog as required by the particular application.
The watchdog timer is a prescaled 16-bit counter that supports up to a 32-bit dynamic range. Out of reset, the
watchdog is disabled in order to allow as much time as needed for code to be loaded into the 5441 on-chip
memory via the HPI. Prior to being enabled, the watchdog counter will, in fact, still count down from its initial
default value using the default prescalar value. When the counter reaches zero, a watchdog time-out event
will occur in that a WD interrupt (WDTINT) request will be sent to the core, and the WDFLAG will be set.
However, since all maskable interrupts are disabled by default at reset, the WDTINT will not be serviced by
the core. Additionally, the watchdog pin (x_WTOUT) is disconnected from the watchdog time-out event, so
no pulse will be generated on this pin. After this time-out, the counter and prescalar will be reloaded
automatically and the watchdog will continue to count, time out, reload, etc. After code-download, the
watchdog can be enabled to connect the x_WTOUT pin to the time-out event. To enable the watchdog, certain
sequence shall be followed as shown in Figure 3–25.
Once the watchdog is enabled, it cannot be disabled by software. It can be disabled by watchdog time-out,
local hardware reset, or global hardware reset. A special key sequence is provided to prevent the watchdog
from being accidentally serviced while the software is trapped in a dead loop or in some other software failures.
December 1999 – Revised April 2002
SPRS122E
35
Functional Overview
3.2.5.1
Watchdog Timer Registers
There are four 16-bit registers associated with the watchdog timer.
•
•
•
•
3.2.5.2
WD Timer Counter Register (WDTIM)
WD Timer Period Register (WDPRD)
WD Timer Control Register (WDTCR)
WD Timer Second Control Register (WDTSCR)
WDTIM Register
This register contains the 16-bit watchdog counter value. It is decremented once every watchdog clock cycle.
3.2.5.3
WDPRD Register
This register is used to reload the WD timer counter register (WDTIM).
3.2.5.4
WDTCR Register
This register provides the control and status information. WDTCR bit fields are as shown in Figure 3–23 and
are described in Table 3–12.
15
14
13
Reserved
12
11
10
9
8
7
SOFT
FREE
PSC
R/W+0
R/W+0
R
6
5
4
3
Reserved
2
1
0
TDDR
R/W+1111
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–23. Watchdog Timer Control Register (WDTCR)
36
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Table 3–12. WDTCR Bit Description
BIT
NO.
BIT
NAME
15–12
Reserved
FUNCTION
Register bit is reserved. Read 0, write has no effect.
Used in conjunction with the FREE bit to determine the state of the timer when a breakpoint is encountered in
the HLL debugger.
SOFT
11
When FREE = 0 and SOFT = 0 the timer stops immediately.
When FREE = 0 and SOFT = 1, the timer stops when the counter decrements to 0.
Used in conjunction with the SOFT bit to determine the state of the timer when a breakpoint is encountered in
the HLL debugger.
FREE
10
When FREE = 0, the SOFT bit selects the timer mode.
When FREE = 1, the timer runs free regardless of the SOFT bit.
9–6
PSC
5–4
Reserved
Timer prescalar counter, used only when PREMD = 0 (in WDTSCR register) and the prescaler is in direct mode.
Register bit is reserved. Read 0, write has no effect.
Timer prescalar.
Case 1: When PREMD = 0, TDDR is a 4-bit reload prescalar. When PSC decrements to 0, PSC is loaded with
the contents of TDDR.
Case 2: When PREMD = 1,TDDR is an indirect prescalar, the contents in TDDR is used to specify the timer
prescalar.
3–0
TDDR
3.2.5.5
TDDR[3:0]
PRESCALAR
0000
0001h
0001
0003h
0010
0007h
0011
000Fh
0100
001Fh
0101
003Fh
0110
007Fh
0111
00FFh
1000
01FFh
1001
03FFh
1010
07FFh
1011
0FFFh
1100
1FFFh
1101
3FFFh
1110
7FFFh
1111
FFFFh (Default)
WDTSCR Register
This 16-bit register contains bits to indicate watchdog flag, to enable watchdog, to set prescalar mode as well
as to provide the 12-bit WDKEY for watchdog service.
WDTSCR bit fields are shown in Figure 3–24 and are described in Table 3–13.
December 1999 – Revised April 2002
SPRS122E
37
Functional Overview
15
14
13
12
11
10
9
8
7
6
5
WDFLAG
WDEN
Reserved
PREMD
WDKEY
R/W+0
R/W+0
R/W+1
R/W+0
4
3
2
1
0
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–24. Watchdog Timer Second Control Register (WDTSCR)
Table 3–13. WDTSCR Bit Description
BIT
BIT
NAME
NO.
FUNCTION
Watchdog flag bit. This bit can be cleared by enabling the watchdog timer, by device global reset, and by being
written with “1”.
15
WDFLAG
It is set by a watchdog time-out.
0=
No watchdog time-out occurred
1=
Watchdog time-out occurred
Watchdog timer enable bit.
14
0=
Watchdog disable. Default value after device reset. Watchdog output pin is disconnected to the
1=
Watchdog enable. Once enabled, the watchdog output pin is connected to the watchdog time-out
watchdog time-out event, counter starts to run.
WDEN
event, and can be disabled by watchdog time-out or reset.
13
Reserved
Register bit is reserved. Read 0, write has no effect.
Prescalar mode select bit.
12
PREMD
0=
Direct mode, TDDR is 4-bit reload prescalar.
1=
Indirect mode, TDDR is used to select individual prescalar value (default value after local or global
hardware reset).
11–0
WDKEY
12-bit watchdog reset key, only the sequence of a 5C6h followed by an A7Eh services the watchdog.
The watchdog has to be serviced periodically with the sequence of 5C6h followed by A7Eh, written to WDKEY
before the watchdog timer times out. Both 5C6h and A7Eh are allowed to be written to WDKEY. Only the
sequence of 5C6h followed by A7Eh, to WDKEY services the watchdog. Any other writes to WDKEY will
trigger the watchdog time-out immediately, and consequently:
•
•
•
the watchdog output pin will generate an active-low pulse (6H ns, H=0.5 clock cycle)
the WDFLAG bit in WDTSCR will be set to 1
the internal maskable WD interrupt (WD_TINT) will be triggered
Read from WDTSCR register will not cause time-out.
When the watchdog is in time-out state, the watchdog is disabled and WDEN is cleared. The watchdog output
pin (x_WTOUT) is disconnected to the watchdog time-out event. Finally, the timer is reloaded and continues
to run.
Out of reset, the watchdog is disabled, and reads and writes to the watchdog registers are allowed. Once 5C6h
is written to WDKEY in the WDTSCR register from the initial state, the watchdog enters the preactive state.
The next write to the WDTSCR register should be completed with a “1” written to WDEN and A7Eh written
to WDKEY. This causes the watchdog timer to enter the active state. Once the watchdog is enabled, it cannot
be disabled by software. Any writes to the WDTSCR register from the active or service states that do not write
5C6h or A7Eh to WDKEY will result in an immediate watchdog time-out. Writing the sequence of 5C6h and
A7Eh to WDKEY causes the watchdog timer to transition between the active and service states. The transition
from the service state to the active state results in the timer register reload that is necessary to keep the
watchdog timer from timing out. Each time the watchdog is serviced by the sequence, the watchdog timer
counter and prescalar will automatically be reloaded.
38
SPRS122E
December 1999 – Revised April 2002
Functional Overview
The registers WDTIM, WDPRD, WDTCR, and the PREMD bit in WDTSCR must be configured before the
watchdog enters the active state. By default, WDTIM =FFFFh, WDPRD = FFFFh, PREMD = 1, TDDR = 1111b.
Writing a ‘1’ to WDEN and configuring the PREMD bit must be done at the same time that A7Eh is written to
WDKEY in watchdog pre-active state.
3.2.5.6
Watchdog State Diagram
Figure 3–25 shows the watchdog operation state diagram.
Power Up/
Reset
(Hardware)
Not 5C6h to
WDKEY
Initial State
(Watchdog
Disabled)
(WDTIM=FFFFh)
(WDPRD=FFFFh)
(TDDR=1111b)
(PREMD=1)
5C6h to
WDKEY
5C6h to WDKEY
Pre-Active
State
Not A7Eh or 5C6h
to WDKEY
A7Eh to
WDKEY
A7Eh to WDKEY
with ”1” to WDEN
(Reload Timer,
Clear WDFLAG,
Enable Output Pin)
Active State
(Waiting for
5C6h)
Not 5C6h or A7Eh
to WDKEY
Output Pin Asserted
WDFLAG Set
WD INT Triggered
5C6h to
WDKEY
A7Eh to
WDKEY
(Register
Reload)
Timeout!
Output Pin Asserted
WDFLAG Set
WD INT Triggered
Timeout
State
(Watchdog
Disabled)
(Output Pin
Disconnected)
Timeout!
Output Pin Asserted
WDFLAG Set
WD INT Triggered
Not A7Eh or 5C6h
to WDKEY
Output Pin Asserted
WDFLAG Set
WD INT Triggered
Service
State
(Waiting for
A7Eh)
5C6h to
WDKEY
Figure 3–25. Watchdog Operation State Diagram
As shown in Figure 3–25, the watchdog is disabled before it enters the active state. Even though disabled,
the WD interrupt (WD_TINT) may be triggered periodically although the watchdog output pin (x_WTOUT) will
not be asserted. The interrupt may be utilized to:
•
•
3.2.5.7
Indicate that watchdog is not in active state
Allow the watchdog timer to act as a general-purpose time counter if the watchdog functionality is not
needed.
Watchdog Register Write Protection
Once the watchdog is enabled, writes to registers WDTIM, WDPRD, and WDTCR will have no effect. Writes
to the WDFLAG, WDEN, and PREMD bits in register WDTSCR will have no effect. However, writing an
incorrect key (not 5C6h or A7Eh) to WDKEY will result in an immediate time-out.
December 1999 – Revised April 2002
SPRS122E
39
Functional Overview
3.2.6 Software-Programmable Phase-Locked Loop (PLL)
The clock generator provides clocks to the 5441 device, and consists of a phase-locked loop (PLL) circuit. The
clock generator requires a reference clock input, which must be provided by using an external clock source.
The reference clock input is then divided by two (DIV mode) to generate clocks for the 5441 device. Alternately,
the PLL circuit can be used (PLL mode) to generate the device clock by multiplying the reference clock
frequency by a scale factor, allowing use of a clock source with a lower frequency than that of the CPU. The
PLL is an adaptive circuit that, once synchronized, locks onto and tracks an input clock signal. When the PLL
is initially started, it enters a transitional mode during which the PLL acquires lock with the input signal. Once
the PLL is locked, it continues to track and maintain synchronization with the input signal. Then, other internal
clock circuitry allows the synthesis of new clock frequencies for use as master clock for the 5441 device. Only
subsystem A controls the PLL. Subsystems B, C, and D cannot access the PLL registers.
The software-programmable PLL features a high level of flexibility, and includes a clock scaler that provides
various clock multiplier ratios, capability to directly enable and disable the PLL, and a PLL lock timer that can
be used to delay switching to PLL clocking mode of the device until lock is achieved. Devices that have a
built-in software-programmable PLL can be configured in one of two clock modes:
•
PLL mode. The input clock (CLKIN) is multiplied by 1 of 31 possible ratios. These ratios are achieved using
the PLL circuitry.
•
DIV (divider) mode. The input clock is divided by 2 or 4. Note that when DIV mode is used, the PLL can
be completely disabled in order to minimize power dissipation.
The software-programmable PLL is controlled using the 16-bit memory-mapped (address 0058h) clock mode
register (CLKMD). The CLKMD register is used to define the clock configuration of the PLL clock module.
Figure 3–26 shows the bit layout of the clock mode register and Table 3–14 describes the bit functions.
15
2
1
0
PLLMUL†
12
11
PLLDIV†
10
PLLCOUNT†
3
PLLON/OFF†
PLLNDIV
STATUS
R/W
R/W
R/W
R/W
R/W
R/W
† When in DIV mode (PLLSTATUS is low), PLLMUL, PLLDIV, PLLCOUNT, and PLLON/OFF are don’t cares, and their contents are indeterminate.
LEGEND: R = Read, W = Write
Figure 3–26. Clock Mode Register (CLKMD)
40
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Table 3–14. Clock Mode Register (CLKMD) Bit Functions
BIT
BIT
NAME
NO.
15–12
PLLMUL†
11
PLLDIV†
FUNCTION
PLL multiplier. PLLMUL defines the frequency multiplier in conjunction with PLLDIV and PLLNDIV. See
Table 3–15.
PLL divider. PLLDIV defines the frequency multiplier in conjunction with PLLMUL and PLLNDIV. See Table 3–15.
10–3
PLLDIV = 0
Means that an integer multiply factor is used
PLLDIV = 1
Means that a noninteger multiply factor is used
PLL counter value. PLLCOUNT specifies the number of input clock cycles (in increments of16 cycles) for the PLL
lock timer to count before the PLL begins clocking the processor after the PLL is started. The PLL counter is a
down-counter, which is driven by the input clock divided by 16; therefore, for every 16 input clocks, the PLL
counter decrements by one.
PLLCOUNT†
The PLL counter can be used to ensure that the processor is not clocked until the PLL is locked, so that only valid
clock signals are sent to the device.
2
PLLON/OFF†
PLL on/off. PLLON/OFF enables or disables the PLL part of the clock generator in conjunction with the PLLNDIV
bit (see Table 3–16). Note that PLLON/OFF and PLLNDIV can both force the PLL to run; when PLLON/OFF is
high, the PLL runs independently of the state of PLLNDIV.
1
PLLNDIV
PLLNDIV configures PLL mode when high or DIV mode when low. PLLNDIV defines the frequency multiplier in
conjunction with PLLDIV and PLLMUL. See Table 3–15.
Indicates the PLL mode.
0
STATUS
STATUS = 0
Indicates DIV mode
STATUS = 1
Indicates PLL mode
† When in DIV mode (PLLSTATUS is low), PLLMUL, PLLDIV, PLLCOUNT, and PLLON/OFF are don’t cares, and their contents are indeterminate.
Table 3–15. Multiplier Related to PLLNDIV, PLLDIV, and PLLMUL
MULTIPLIER‡
PLLNDIV
PLLDIV
PLLMUL
0
x
0–14
0.5
0
x
15
0.25
1
0
0–14
PLLMUL + 1
1
0
15
bypass (multiply by 1)
1
1
0 or even
(PLLMUL + 1)/2
1
1
odd
PLLMUL/4
‡ CLKOUT = CLKIN * Multiplier
Table 3–16. VCO Truth Table
3.2.6.1
PLLON/OFF
PLLNDIV
VCO STATE
0
0
off
1
0
on
0
1
on
1
1
on
PLL Clock Programmable Timer
During the lockup period, the PLL should not be used to clock the 5441. The PLLCOUNT programmable lock
timer provides a convenient method of automatically delaying clocking of the device by the PLL until lock is
achieved.
The PLL lock timer is a counter, loaded from the PLLCOUNT field in the CLKMD register, that decrements from
its preset value to 0. The timer can be preset to any value from 0 to 255, and its input clock is CLKIN divided
by 16. The resulting lockup delay can therefore be set from 0 to 255 × 16 CLKIN cycles.
December 1999 – Revised April 2002
SPRS122E
41
Functional Overview
The lock timer is activated when the operating mode of the clock generator is switched from DIV to PLL. During
the lockup period, the clock generator continues to operate in DIV mode; after the PLL lock timer decrements
to zero, the PLL begins clocking the 5441.
Accordingly, the value loaded into PLLCOUNT is chosen based on the following formula:
PLLCOUNT +
Lockup Time
16
T CLKIN
where TCLKIN is the input reference clock period and lockup time is the required VCO lockup time, as shown
in Table 3–17.
Table 3–17. VCO Lockup Time
CLKOUT FREQUENCY (MHz)
LOCKUP TIME (µs)†
5
23
10
17
20
16
40
19
60
24
80
29
100
35
135
45
† Approximate values
3.2.6.2
CLKMD Register Initialization At Reset
The clock mode pin (CLKMD) is used to initialize the PLL to a known value at reset. The CLKMD pin is sampled
when the reset signal is low. Only global reset (RESET) will reset the PLL. Subsystem A local reset (A_RS)
has no effect on the PLL.
Table 3–18. PLL Initialization at Reset
CLKMD PIN
PLL MODE
0
Bypass
1
CLKINx2
3.2.7 General-Purpose I/O
The 5441 has 16 general-purpose I/O pins. These pins are:
A_GPIO0, A_GPIO1, A_GPIO2, A_GPIO3
B_GPIO0, B_GPIO1, B_GPIO2, B_GPIO3
C_GPIO0, C_GPIO1, C_GPIO2, C_GPIO3
D_GPIO0, D_GPIO1, D_GPIO2, D_GPIO3
Four bits of general-purpose I/O are available to each core. Each GPIO pin can be individually selected as
either an input or an output through the GPIO register. The x_XF, x_BIO, and timer output are selectable on
GPIO pins 0, 1, and 3 through the GPIO register also. Each output driver has an independent three-state
control. All nonreserved GPIO register bits are readable and writeable. The GPIO register bits will be set
to 0 when the core is in reset, which will configure all GPIO as inputs. GPIO data and control bits are accessible
through a memory-mapped register at 3Ch with the format shown in Figure 3–27 and the bit functions
described in Table 3–19.
42
SPRS122E
December 1999 – Revised April 2002
Functional Overview
15
14
13
12
11
10
9
8
7
6
TOUT
Rsvd
X_BIO
X_XF
GPIO
DIR3
GPIO
DIR2
GPIO
DIR1
GPIO
DIR0
CLK
OUT1
CLK
OUT0
R/W+0
R/W+0
R/W+0
R/W+0
R/W+0
R/W+0
R/W+0
R/W+0
R/W+0
5
4
Reserved
3
2
1
0
GPIO
DAT3
GPIO
DAT2
GPIO
DAT1
GPIO
DAT0
R/W+0
R/W+0
R/W+0
R/W+0
LEGEND: R = Read, W = Write, +0 = Value at reset
Figure 3–27. General-Purpose I/O Control Register
Table 3–19. General-Purpose I/O Control Register Bit Functions
BIT
NO.
BIT
NAME
15
TOUT
14
Reserved
13
X_BIO
12
X XF
X_XF
11 8
11–8
GPIO
DIRn†
BIT
VALUE
FUNCTION
0
Timer output disable. Uses GPIO3 as general-purpose I/O.
1
Timer output enable. Overrides DIR3. Timer output is driven on GPIO3 and readable in DAT3.
X
Register bit is reserved. Read 0, write has no effect.
0
Branch control input disable. Uses GPIO1 as general-purpose I/O.
1
Branch control input enable. Overrides DIR1. The X_BIO output is driven on GPIO1 and readable in
DAT0.
0
External flag output disable. Uses GPIO0 as general-purpose I/O.
1
External flag output enable. Overrides DIR0. The X_XF output is driven on GPIO0 and readable in DAT1.
0
GPIOn pin is used as an input.
1
GPIOn pin is used as an output.
CLKOUT muxing selection bits.
CLKOUT1[7]
7–6
CLKOUT
CLKOUT0[6]
A_CLKOUT
(default)
0
0
B_CLKOUT
0
1
C_CLKOUT
1
0
D_CLKOUT
1
1
5–4
Reserved
X
Register bit is reserved. Read 0, write has no effect.
GPIO
DATn†
0
GPIOn is driven with a 0 (DIRn = 1). GPIOn is read as 0 (DIRn = 0).
3 0
3–0
1
GPIOn is driven with a 1 (DIRn = 1). GPIOn is read as 1 (DIRn = 0).
† n = 3, 2, 1, or 0
The timer output (TOUT) bit is used to multiplex the output of the timer and GPIO3. The X_XF bit is used to
multiplex the output of the external flag, and the X_BIO bit is used to multiplex the input of the branch control.
The watchdog enable (WDEN) bit in the watchdog timer second control register (WDTSCR) is used to
multiplex the watchdog timer output and GPIO2. All GPIO pins are programmable as an input or output by the
direction bit (GPIODIRn). Data is either driven or read from the data bit field (GPIODATn). GPIODIR3 has no
effect when TOUT = 1.
December 1999 – Revised April 2002
SPRS122E
43
Functional Overview
3.2.8 Chip Subsystem ID Register
The chip subsystem ID register (CSIDR) is a read-only memory-mapped register located at 3Eh within each
DSP subsystem. This register contains two elements for electrically readable device identification. The
Chip ID bits identify the type of C54x device (41h for 5441). The SubSysID contains a unique subsystem
identifier. Figure 3–28 shows the CSIDR and Table 3–20 describes its bit functions.
15
14
13
12
11
10
9
8
7
6
Chip ID
5
4
3
2
Reserved
1
0
SubSysID
R
R
LEGEND: R = Read
Figure 3–28. Chip Subsystem ID Register (CSIDR)
Table 3–20. Chip Subsystem ID Register Bit Functions
BIT
NO.
BIT FIELD
NAME
15 8
15–8
Chip ID
7–4
Reserved
3 0
3–0
SubSysID
FUNCTION
54x device type.
type Contains 41h for 5441.
5441
Identifier for DSP subsystem: A = 00b,
00b B = 01b,
01b C = 10b,
10b and D = 11b
3.2.9 Data Memory Map Register
To access the extended data memory, the DSP CPU need to configure the data memory map register
(DMMR), which is used to point to extended data memory. The content of DMMR register is used to select
the extended data for all CPU data memory accesses. Figure 3–29 shows the DMMR and Table 3–21
describes its bit functions.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Extended
Data
Reserved
R/W+0
LEGEND: R = Read, W = Write
Figure 3–29. Data Memory Map Register (DMMR)
Table 3–21. Data Memory Map Register Functions
BIT
NO.
BIT FIELD
NAME
15–1
Reserved
FUNCTION
Extended data memory for CPU access:
0
Extended data
Extended Data = 0b,
0b DARAM2 and DARAM3 are mapped in
Extended_Data
in.
Extended_Data = 1b, DARAM4 and DARAM5 are mapped in.
44
SPRS122E
December 1999 – Revised April 2002
Functional Overview
3.3
Memory-Mapped Registers
The 5441 has 27 processor memory-mapped registers, which are mapped in data memory space addresses
0h to 1Fh as shown in Table 3–22. Each device also has a set of memory-mapped registers associated with
the peripherals as shown in Table 3–23.
Table 3–22. Processor Memory-Mapped Registers for Each DSP Subsystem
NAME
ADDRESS
DEC
HEX
DESCRIPTION
IMR
0
0
Interrupt Mask Register
IFR
1
1
Interrupt Flag Register
—
2–5
2–5
ST0
6
6
Status Register 0
ST1
7
7
Status Register 1
AL
8
8
Accumulator A Low Word (15–0)
AH
9
9
Accumulator A High Word (31–16)
AG
10
A
Accumulator A Guard Bits (39–32)
BL
11
B
Accumulator B Low Word (15–0)
BH
12
C
Accumulator B High Word (31–16)
BG
13
D
Accumulator B Guard Bits (39–32)
TREG
14
E
Temporary Register
TRN
15
F
Transition Register
AR0
16
10
Auxiliary Register 0
AR1
17
11
Auxiliary Register 1
AR2
18
12
Auxiliary Register 2
AR3
19
13
Auxiliary Register 3
AR4
20
14
Auxiliary Register 4
AR5
21
15
Auxiliary Register 5
AR6
22
16
Auxiliary Register 6
AR7
23
17
Auxiliary Register 7
SP
24
18
Stack Pointer
BK
25
19
Circular Buffer Size Register
BRC
26
1A
Block-Repeat Counter
RSA
27
1B
Block-Repeat Start Address
REA
28
1C
Block-Repeat End Address
PMST
29
1D
Processor Mode Status Register
XPC
30
1E
Extended Program Counter
—
31
1F
Reserved
December 1999 – Revised April 2002
Reserved for testing
SPRS122E
45
Functional Overview
Table 3–23. Peripheral Memory-Mapped Registers for Each DSP Subsystem
NAME
ADDRESS
(HEX)
DESCRIPTION
DRR20
20
McBSP 0 Data Receive Register 2
DRR10
21
McBSP 0 Data Receive Register 1
DXR20
22
McBSP 0 Data Transmit Register 2
DXR10
23
McBSP 0 Data Transmit Register 1
TIM
24
Timer Register
PRD
25
Timer Period Register
TCR
26
Timer Control Register
TSCR
27
Timer Second Control Register
–
28
Reserved
BSCR
29
Bank-Switching Control Register
—
2A–2B
HPIC
2C
—
2D–2F
Reserved
HPI Control Register (HMODE=0 only)
Reserved
DRR22
30
McBSP 2 Data Receive Register 2
DRR12
31
McBSP 2 Data Receive Register 1
DXR22
32
McBSP 2 Data Transmit Register 2
DXR12
33
McBSP 2 Data Transmit Register 1
SPSA2
34
McBSP 2 Subbank Address Register†
McBSP 2 Subbank Data Register†
SPSD2
—
35
36–37
SPSA0
SPSD0
—
38
39
3A–3B
Reserved
McBSP 0 Subbank Address Register†
McBSP 0 Subbank Data Register†
Reserved
GPIO
3C
General-Purpose I/O Register
—
3D
Reserved
CSIDR
3E
Chip Subsystem ID register
—
3F
Reserved
DRR21
40
McBSP 1 Data Receive Register 2
DRR11
41
McBSP 1 Data Receive Register 1
DXR21
42
McBSP 1 Data Transmit Register 2
DXR11
43
McBSP 1 Data Transmit Register 1
—
44–47
SPSA1
48
SPSD1
49
—
4A–4B
Reserved
McBSP 1 Subbank Address Register†
McBSP 1 Subbank Data Register†
Reserved
TIM
4C
Watchdog Timer Register
PRD
4D
Watchdog Timer Period Register
TCR
4E
Watchdog Timer Control Register
WDTSCR
4F
Watchdog Timer Second Control Register
DMMR
50
Data Memory Map Register
—
51–53
DMPREC
54
DMSA
55
Reserved
DMA Priority and Enable Control Register
DMA Subbank Address Register‡
DMSDI
56
DMA Subbank Data Register with Autoincrement‡
†See Table 3–24 for a detailed description of the McBSP control registers and their subaddresses.
‡See Table 3–25 for a detailed description of the DMA subbank addressed registers.
46
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Table 3–23. Peripheral Memory-Mapped Registers for Each DSP Subsystem (Continued)
ADDRESS
(HEX)
NAME
DESCRIPTION
DMSDN
57
DMA Subbank Data Register‡
CLKMD
58
Clock Mode Register (CLKMD), subsystem A only (reserved in subsystems B, C, and D)
—
59–5F
Reserved
†See Table 3–24 for a detailed description of the McBSP control registers and their subaddresses.
‡See Table 3–25 for a detailed description of the DMA subbank addressed registers.
3.4
McBSP Control Registers and Subaddresses
The control registers for the multichannel buffered serial port (McBSP) are accessed using the subbank
addressing scheme. This allows a set or subbank of registers to be accessed through a single memory
location. The McBSP subbank address register (SPSAx) is used as a pointer to select a particular register
within the subbank. The McBSP data register (SPSDx) is used to access (read or write) the selected register.
Table 3–24 shows the McBSP control registers and their corresponding subaddresses.
Table 3–24. McBSP Control Registers and Subaddresses
McBSP0
McBSP1
McBSP2
NAME
ADDRESS
NAME
ADDRESS
SUBSUB
ADDRESS
39h
SPCR11
49h
SPCR12
35h
00h
Serial port control register 1
39h
SPCR21
49h
SPCR22
35h
01h
Serial port control register 2
RCR10
39h
RCR11
49h
RCR12
35h
02h
Receive control register 1
RCR20
39h
RCR21
49h
RCR22
35h
03h
Receive control register 2
XCR10
39h
XCR11
49h
XCR12
35h
04h
Transmit control register 1
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
NAME
ADDRESS
SPCR10
SPCR20
DESCRIPTION
XCR20
39h
XCR21
49h
XCR22
35h
05h
Transmit control register 2
SRGR10
39h
SRGR11
49h
SRGR12
35h
06h
Sample rate generator register 1
SRGR20
39h
SRGR21
49h
SRGR22
35h
07h
Sample rate generator register 2
MCR10
39h
MCR11
49h
MCR12
35h
08h
Multichannel register 1
MCR20
39h
MCR21
49h
MCR22
35h
09h
Multichannel register 2
RCERA0
39h
RCERA1
49h
RCERA2
35h
0Ah
Receive channel enable register partition A
RCERB0
39h
RCERB1
49h
RCERB2
35h
0Bh
Receive channel enable register partition B
XCERA0
39h
XCERA1
49h
XCERA2
35h
0Ch
Transmit channel enable register partition A
XCERB0
39h
XCERB1
49h
XCERB2
35h
0Dh
Transmit channel enable register partition B
PCR0
39h
PCR1
49h
PCR2
35h
0Eh
Pin control register
RCERC0
39h
RCERC1
49h
RCERC2
35h
010h
Receive channel enable register partition C
RCERD0
39h
RCERD1
49h
RCERD2
35h
011h
Receive channel enable register partition D
XCERC0
39h
XCERC1
49h
XCERC2
35h
012h
Transmit channel enable register partition C
XCERD0
39h
XCERD1
49h
XCERD2
35h
013h
Transmit channel enable register partition D
RCERE0
39h
RCERE1
49h
RCERE2
35h
014h
Receive channel enable register partition E
RCERF0
39h
RCERF1
49h
RCERF2
35h
015h
Receive channel enable register partition F
XCERE0
39h
XCERE1
49h
XCERE2
35h
016h
Transmit channel enable register partition E
XCERF0
39h
XCERF1
49h
XCERF2
35h
017h
Transmit channel enable register partition F
RCERG0
39h
RCERG1
49h
RCERG2
35h
018h
Receive channel enable register partition G
RCERH0
39h
RCERH1
49h
RCERH2
35h
019h
Receive channel enable register partition H
XCERG0
39h
XCERG1
49h
XCERG2
35h
01Ah
Transmit channel enable register partition G
XCERH0
39h
XCERH1
49h
XCERH2
35h
01Bh
Transmit channel enable register partition H
December 1999 – Revised April 2002
SPRS122E
47
Functional Overview
3.5
DMA Subbank Addressed Registers
The direct memory access (DMA) controller has several control registers associated with it. The main control
register (DMPREC) is a standard memory-mapped register. However, the other registers are accessed using
the subbank addressing scheme. This allows a set or subbank of registers to be accessed through a single
memory location. The DMA subbank address (DMSA) register is used as a pointer to select a particular
register within the subbank, while the DMA subbank data (DMSDN) register or the DMA subbank data register
with autoincrement (DMSDI) is used to access (read or write) the selected register.
When the DMSDI register is used to access the subbank, the subbank address is automatically
postincremented so that a subsequent access affects the next register within the subbank. This autoincrement
feature is intended for efficient, successive accesses to several control registers. If the autoincrement feature
is not required, the DMSDN register should be used to access the subbank. Table 3–25 shows the DMA
controller subbank addressed registers and their corresponding subaddresses.
Table 3–25. DMA Subbank Addressed Registers
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ADDRESS
SUBADDRESS
DMSRC0
56h/57h
00h
DMA channel 0 source address register
DMDST0
56h/57h
01h
DMA channel 0 destination address register
DMCTR0
56h/57h
02h
DMA channel 0 element count register
DMSFC0
56h/57h
03h
DMA channel 0 sync select and frame count register
DMMCR0
56h/57h
04h
DMA channel 0 transfer mode control register
DMSRC1
56h/57h
05h
DMA channel 1 source address register
DMDST1
56h/57h
06h
DMA channel 1 destination address register
DMCTR1
56h/57h
07h
DMA channel 1 element count register
DMSFC1
56h/57h
08h
DMA channel 1 sync select and frame count register
DMMCR1
56h/57h
09h
DMA channel 1 transfer mode control register
DMSRC2
56h/57h
0Ah
DMA channel 2 source address register
DMDST2
56h/57h
0Bh
DMA channel 2 destination address register
DMCTR2
56h/57h
0Ch
DMA channel 2 element count register
DMSFC2
56h/57h
0Dh
DMA channel 2 sync select and frame count register
DMMCR2
56h/57h
0Eh
DMA channel 2 transfer mode control register
DMSRC3
56h/57h
0Fh
DMA channel 3 source address register
DMDST3
56h/57h
10h
DMA channel 3 destination address register
DMCTR3
56h/57h
11h
DMA channel 3 element count register
DMSFC3
56h/57h
12h
DMA channel 3 sync select and frame count register
DMMCR3
56h/57h
13h
DMA channel 3 transfer mode control register
DMSRC4
56h/57h
14h
DMA channel 4 source address register
DMDST4
56h/57h
15h
DMA channel 4 destination address register
DMCTR4
56h/57h
16h
DMA channel 4 element count register
DMSFC4
56h/57h
17h
DMA channel 4 sync select and frame count register
DMMCR4
56h/57h
18h
DMA channel 4 transfer mode control register
DMSRC5
56h/57h
19h
DMA channel 5 source address register
DMDST5
56h/57h
1Ah
DMA channel 5 destination address register
DMCTR5
56h/57h
1Bh
DMA channel 5 element count register
DMSFC5
56h/57h
1Ch
DMA channel 5 sync select and frame count register
DMMCR5
56h/57h
1Dh
DMA channel 5 transfer mode control register
DMSRCP
56h/57h
1Eh
DMA source program page address (common channel)
NAME
48
SPRS122E
DESCRIPTION
December 1999 – Revised April 2002
Functional Overview
Table 3–25. DMA Subbank Addressed Registers (Continued)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ADDRESS
SUBADDRESS
DMDSTP
56h/57h
1Fh
DMA destination program page address (common channel)
DMIDX0
56h/57h
20h
DMA element index address register 0
DMIDX1
56h/57h
21h
DMA element index address register 1
DMFRI0
56h/57h
22h
DMA frame index register 0
DMFRI1
56h/57h
23h
DMA frame index register 1
DMGSA0
56h/57h
24h
DMA channel 0 global source address reload register
DMGDA0
56h/57h
25h
DMA channel 0 global destination address reload register
DMGCR0
56h/57h
26h
DMA channel 0 global count reload register
DMGFR0
56h/57h
27h
DMA channel 0 global frame count reload register
–
56h/57h
28h
Reserved
–
56h/57h
29h
Reserved
DMGSA1
56h/57h
2Ah
DMA channel 1 global source address reload register
DMGDA1
56h/57h
2Bh
DMA channel 1 global destination address reload register
DMGCR1
56h/57h
2Ch
DMA channel 1 global count reload register
DMGFR1
56h/57h
2Dh
DMA channel 1 global frame count reload register
DMGSA2
56h/57h
2Eh
DMA channel 2 global source address reload register
DMGDA2
56h/57h
2Fh
DMA channel 2 global destination address reload register
DMGCR2
56h/57h
30h
DMA channel 2 global count reload register
DMGFR2
56h/57h
31h
DMA channel 2 global frame count reload register
DMGSA3
56h/57h
32h
DMA channel 3 global source address reload register
DMGDA3
56h/57h
33h
DMA channel 3 global destination address reload register
DMGCR3
56h/57h
34h
DMA channel 3 global count reload register
DMGFR3
56h/57h
35h
DMA channel 3 global frame count reload register
DMGSA4
56h/57h
36h
DMA channel 4 global source address reload register
DMGDA4
56h/57h
37h
DMA channel 4 global destination address reload register
DMGCR4
56h/57h
38h
DMA channel 4 global count reload register
DMGFR4
56h/57h
39h
DMA channel 4 global frame count reload register
DMGSA5
56h/57h
3Ah
DMA channel 5 global source address reload register
DMGDA5
56h/57h
3Bh
DMA channel 5 global destination address reload register
DMGCR5
56h/57h
3Ch
DMA channel 5 global count reload register
DMGFR5
56h/57h
3Dh
DMA channel 5 global frame count reload register
DMSRCDP0
56h/57h
3Eh
DMA channel 0 extended source data page register
DMDSTDP0
56h/57h
3Fh
DMA channel 0 extended destination data page register
DMSRCDP1
56h/57h
40h
DMA channel 1 extended source data page register
DMDSTDP1
56h/57h
41h
DMA channel 1 extended destination data page register
DMSRCDP2
56h/57h
42h
DMA channel 2 extended source data page register
DMDSTDP2
56h/57h
43h
DMA channel 2 extended destination data page register
DMSRCDP3
56h/57h
44h
DMA channel 3 extended source data page register
DMDSTDP3
56h/57h
45h
DMA channel 3 extended destination data page register
DMSRCDP4
56h/57h
46h
DMA channel 4 extended source data page register
DMDSTDP4
56h/57h
47h
DMA channel 4 extended destination data page register
NAME
December 1999 – Revised April 2002
DESCRIPTION
SPRS122E
49
Functional Overview
Table 3–25. DMA Subbank Addressed Registers (Continued)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ADDRESS
SUBADDRESS
DMSRCDP5
56h/57h
48h
DMA channel 5 extended source data page register
DMDSTDP5
56h/57h
49h
DMA channel 5 extended destination data page register
NAME
3.6
DESCRIPTION
Interrupts
Vector-relative locations and priorities for all internal and external interrupts are shown in Table 3–26.
Table 3–26. 5441 Interrupt Locations and Priorities for Each DSP Subsystem
NAME
LOCATION
DECIMAL
HEX
RS, SINTR
0
00
NMI, SINT16
4
SINT17
8
SINT18
PRIORITY
FUNCTION
1
Reset (Hardware and Software Reset)
04
2
Nonmaskable Interrupt
08
—
Software Interrupt #17
12
0C
—
Software Interrupt #18
SINT19
16
10
—
Software Interrupt #19
SINT20
20
14
—
Software Interrupt #20
SINT21
24
18
—
Software Interrupt #21
SINT22
28
1C
—
Software Interrupt #22
SINT23
32
20
—
Software Interrupt #23
SINT24
36
24
—
Software Interrupt #24
SINT25
40
28
—
Software Interrupt #25
SINT26
44
2C
—
Software Interrupt #26
SINT27
48
30
—
Software Interrupt #27
SINT28
52
34
—
Software Interrupt #28
SINT29
56
38
—
Software Interrupt #29
SINT30
60
3C
—
Software Interrupt #30
INT, SINT0
64
40
3
External User Interrupt
WDTINT, SINT1
68
44
4
Watchdog Timer Interrupt
INT2, SINT2
72
48
5
Software interrupt #2
TINT, SINT3
76
4C
6
External Timer Interrupt
BRINT0, SINT4
80
50
7
BSP #0 Receive Interrupt
BXINT0, SINT5
84
54
8
BSP #0 Transmit Interrupt
BRINT2, DMAC0
88
58
9
BSP #2 Receive Interrupt or DMA Channel 0
BXINT2, DMAC1
92
5C
10
BSP #2 Receive Interrupt or DMA Channel 1
INT3, SINT8
96
60
11
Software interrupt #8
HPINT, SINT9
100
64
12
HPI Interrupt (from DSPINT in HPIC)
BRINT1, DMAC2
104
68
13
BSP #1 Receive Interrupt or DMA Channel 2
BXINT1, DMAC3
108
6C
14
BSP #1 transmit Interrupt or DMA channel 3
DMAC4, SINT12
112
70
15
DMA Channel 4
DMAC5, SINT13
116
74
16
DMA Channel 5
120–127
78–7F
—
Reserved
—
50
SPRS122E
December 1999 – Revised April 2002
Functional Overview
Figure 3–30 shows the bit layout of the IMR and the IFR. Table 3–27 describes the bit functions.
15
14
Reserved
13
12
11
10
9
8
DMAC5
DMAC4
XINT1 or
DMAC3
RINT1 or
DMAC2
HPINT
Reserved
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
XINT2 or
DMAC1
RINT2 or
DMAC0
XINT0
RINT0
TINT
Reserved
WDTINT
INT
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R = Read, W = Write
Figure 3–30. Bit Layout of the IMR and IFR Registers for Each Subsystem
Table 3–27. Bit Functions for IMR and IFR Registers for Each DSP Subsystem
BIT
NO.
BIT
NAME
BIT
VALUE
15–14
Reserved
X
Register bit is reserved.
0
IFR/IMR: DMA Channel 5 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 5 has an interrupt pending/is enabled.
0
IFR/IMR: DMA Channel 4 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 4 has an interrupt pending/is enabled.
0
IFR/IMR: McBSP_1 has no transmit interrupt pending/is disabled (masked).
1
IFR/IMR: McBSP_1 has a transmit interrupt pending/is enabled.
0
IFR/IMR: DMA Channel 3 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 3 has an interrupt pending/is enabled.
0
IFR/IMR: McBSP_1 has no receive interrupt pending/is disabled (masked).
13
12
DMAC5
DMAC4
XINT1
11
DMAC3
RINT1
10
DMAC2
9
HPINT
8
Reserved
XINT2
7
DMAC1
RINT2
6
DMAC0
5
4
XINT0
RINT0
FUNCTION
1
IFR/IMR: McBSP_1 has a receive interrupt pending/is enabled.
0
IFR/IMR: DMA Channel 2 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 2 has an interrupt pending/is enabled.
0
IFR/IMR: Host-port interface has no DSPINT interrupt pending/is disabled (masked).
1
IFR/IMR: Host-port interface has an DSPINT interrupt pending/is enabled.
X
Register bit is reserved.
0
IFR/IMR: McBSP_2 has no transmit interrupt pending/is disabled (masked).
1
IFR/IMR: McBSP_2 has a transmit interrupt pending/is enabled.
0
IFR/IMR: DMA Channel 1 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 1 has an interrupt pending/is enabled.
0
IFR/IMR: McBSP_2 has no receive interrupt pending/is disabled (masked).
1
IFR/IMR: McBSP_2 has a receive interrupt pending/is enabled.
0
IFR/IMR: DMA Channel 0 has no interrupt pending/is disabled (masked).
1
IFR/IMR: DMA Channel 0 has an interrupt pending/is enabled.
0
IFR/IMR: McBSP_0 has no receive interrupt pending/is disabled (masked).
1
IFR/IMR: McBSP_0 has a receive interrupt pending/is enabled.
0
IFR/IMR: McBSP_0 has no receive interrupt pending/is disabled (masked).
1
IFR/IMR: McBSP_0 has a receive interrupt pending/is enabled.
December 1999 – Revised April 2002
SPRS122E
51
Functional Overview
Table 3–27. Bit Functions for IMR and IFR Registers for Each DSP Subsystem (Continued)
BIT
NO.
BIT
NAME
3
TINT
2
Reserved
1
0
3.7
WDTINT
INT
BIT
VALUE
FUNCTION
0
IFR/IMR: Timer has no interrupt pending/is disabled (masked).
1
IFR/IMR: Timer has an interrupt pending/is enabled.
X
Register bit is reserved.
0
IFR/IMR: Watchdog interrupt has no interrupt pending/is disabled (masked).
1
IFR/IMR: Watchdog interrupt has an interrupt pending/is enabled.
0
IFR/IMR: Ext user interrupt pin 0 has no interrupt pending/is disabled (masked).
1
IFR/IMR: Ext user interrupt pin 0 has an interrupt pending/is enabled.
IDLE3 Power-Down Mode
The IDLE1 and IDLE2 power-down modes operate as described in the TMS320C54x DSP Reference Set,
Volume 1: CPU and Peripherals (literature number SPRU131). The IDLE3 mode is special in that the clocking
circuitry is shut off to conserve power. The 5441 cannot enter an IDLE3 mode unless all the subsystems
execute an IDLE3 instruction. The power-reduced benefits of IDLE3 cannot be realized until all the
subsystems enter the IDLE3 state and the internal clocks are automatically shut off. The order in which
subsystems enter IDLE3 does not matter.
3.8
Emulating the 5441 Device
The 5441 is a single device, but actually consists of four independent subboundary systems that contain
register/status information used by the emulator tools. Code Composer Studio has a setup wizard called
“Code Composer Setup.” The setup wizard prompts the user for the I/O address of the XDSSIO card and the
number of processors in the system. The board.dat file is then created and placed in the correct directory
automatically. The board.dat file contents would look something like this:
“CPU_D” TI320C5xx
“CPU_C” TI320C5xx
“CPU_B” TI320C5xx
“CPU_A” TI320C5xx
The subsystems are serially connected together internally. Emulation information is serially transmitted into
the device using TDI. The device responds with serial scan information transmitted out the TDO pin.
Code Composer Studio is a trademark of Texas Instruments.
52
SPRS122E
December 1999 – Revised April 2002
Documentation Support
4
Documentation Support
Extensive documentation supports all TMS320 DSP family of devices from product announcement through
applications development. The following types of documentation are available to support the design and use
of the C5000 platform of DSPs:
•
•
•
•
•
TMS320C54x DSP Functional Overview (literature number SPRU307)
Device-specific data sheets
Complete User Guides
Development-support tools
Hardware and software application reports
The five-volume TMS320C54x DSP Reference Set (literature number SPRU210) consists of:
•
•
•
•
•
Volume 1: CPU and Peripherals (literature number SPRU131)
Volume 2: Mnemonic Instruction Set (literature number SPRU172)
Volume 3: Algebraic Instruction Set (literature number SPRU179)
Volume 4: Applications Guide (literature number SPRU173)
Volume 5: Enhanced Peripherals (literature number SPRU302)
The reference set describes in detail the TMS320C54x DSP products currently available and the hardware
and software applications, including algorithms, for fixed-point TMS320 DSP devices.
A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal
processing research and education. The TMS320 DSP newsletter, Details on Signal Processing, is
published quarterly and distributed to update TMS320 DSP customers on product information.
Information regarding Texas Instruments (TI) DSP products is also available on the Worldwide Web at
http://www.ti.com uniform resource locator (URL).
TMS320 and C5000 are trademarks of Texas Instruments.
December 1999 – Revised April 2002
SPRS122E
53
Electrical Specifications
5
Electrical Specifications
This section provides the absolute maximum ratings and the recommended operating conditions for the
TMS320VC5441 DSP.
Leading “x” in signal names identifies the subsystem; x = A, B, C, or D for subsystem A, B, C, or D, respectively.
Trailing “n” in signal names identifies the McBSP; n = 0, 1, or 2 for McBSP0, McBSP1, or McBSP2, respectively.
5.1
Absolute Maximum Ratings
The list of absolute maximum ratings are specified over operating case temperature. Stresses beyond those
listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated
under Section 5.2 is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability. All voltage values are with respect to VSS. Figure 5–1 provides the test load circuit
values for a 3.3-V device.
Supply voltage I/O range, DVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 4.0 V
Supply voltage core range, CVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 2.0 V
Supply voltage analog PLL, VCCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 2.0 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to DVDD + 0.5 V
Output voltage range, Vo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to DVDD + 0.5 V
Operating case temperature range, TC (Commercial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 85°C
TC (Industrial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 100°C
Storage temperature range Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65C to 150C
5.2
Recommended Operating Conditions
MIN
NOM
MAX
3
3.3
3.6
V
CVDD
Device supply voltage, core†
1.55
1.6
1.65
V
VCCA
VSS
Device supply voltage, PLL
1.55
1.6
1.65
V
DVDD
Device supply voltage, I/O†
Supply voltage, GND
0
Schmitt triggered inputs
VIH
High-level
High
level in
input
ut voltage, I/O
DVDD + 0.3
2
DVDD + 0.3
DVDD = 3.3 ± 0.3 V
0
0.3DVDD
All other inputs
0
0.8
All other inputs
Schmitt triggered inputs
VIL
Low-level
Low
level input
in ut voltage, I/O
IOH
High-level output current
IOL
Low-level output current
Operating case temperature, Commercial
TC
Operating case temperature, Industrial
V
0.7DVDD
DVDD = 3.3 ± 0.3 V
UNIT
V
V
–1
mA
1.5
mA
0
85
–40
100
°C
† Texas Instrument DSPs do not require specific power sequencing between the core supply and the I/O supply. However, systems should be
designed to ensure that neither supply is powered up for extended periods of time if the other supply is below the proper operating voltage.
Excessive exposure to these conditions can adversely affect the long-term reliability of the devices. System-level concerns such as bus
contention may require supply sequencing to be implemented. In this case, the core supply should be powered up at the same time as or prior
to the I/O buffers, and then powered down after the I/O buffers.
54
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.3
Electrical Characteristics Over Recommended Operating Case Temperature
Range (Unless Otherwise Noted)
PARAMETER
TEST CONDITIONS
MIN
TYP†
MAX
UNIT
VOH
VOL
High-level output voltage‡
Low-level output voltage‡
VDD = 3.3 ± 0.3 V, IOH = MAX
IOL = MAX
2.4
0.4
V
IIZ
Input current in high impedance
10
–10
10
A
µA
TRST
VDD = MAX
MAX, VO = VSS to VDD
With internal pulldown
10
300
See pin descriptions
With internal pullups
–300
–10
II
Input current
(VI = VSS to VDD)
D[15:0], HA[18:0]
Bus holders enabled, VDD = MAX||
–275
275
–10
10
All other input-only pins
IDDC
Supply current, all four core CPUs
CVDD = 1.6 V, fx = 133 MHz§,
TC = 25°C
IDDP
Supply current, pins
IDDA
Supply current, PLL
IDDC
Supply current,
current standby
Ci
Input capacitance
V
A
µA
200¶
mA
DVDD = 3.3 V, fclock = 133 MHz¶,
TC = 25°C#
40
mA
3
mA
IDLE2
PLL × n mode, 20 MHz input
10
mA
IDLE3
PLL x n mode, 20 MHz input
3
mA
5
pF
Co
Output capacitance
5
pF
† All values are typical unless otherwise specified.
‡ All input and output voltage levels except x_RS, x_INT, x_NMI, CLKIN, x_BCLKX0, x_BCLKR0, BCLKX2, BCLKR2, HAS, HCS, HDS1, HDS2,
and RESET are LVTTL-compatible.
§ Clock mode: PLL × 1 with external source
¶ This value is based on 50% usage of MAC and 50% usage of NOP instructions. Actual operating current varies with the program being executed.
# This value was obtained using the following conditions: HPI in multiplexed mode with address autoincrement, HPI read, CLKOFF = 0, full-duplex
operation of all 12 McBSPs at a rate of 10 million bits per second each, and 15-pF loads on all outputs. For more details on how this calculation
is performed, refer to the Calculation of TMS320LC54x Power Dissipation Application Report (literature number SPRA164).
|| VIL(MIN) ≤ VI ≤ VIL(MAX) or VIH(MIN) ≤ VI ≤ VIH(MAX)
IOL
50 Ω
Tester Pin
Electronics
VLoad
CT
Output
Under
Test
IOH
Where:
IOL
IOH
VLoad
CT
=
=
=
=
1.5 mA (all outputs)
300 µA (all outputs)
1.6 V
20 pF typical load circuit capacitance
Figure 5–1. 3.3-V Test Load Circuit
December 1999 – Revised April 2002
SPRS122E
55
Electrical Specifications
5.4
Package Thermal Resistance Characteristics
Table 5–1 provides the thermal resistance characteristics for the recommended package types used on the
TMS320VC5441 DSP.
Table 5–1. Thermal Resistance Characteristics
5.5
PARAMETER
GGU
PACKAGE
PGF
PACKAGE
UNIT
RΘJA
38
56
°C / W
RΘJC
5
5
°C / W
Timing Parameter Symbology
Timing parameter symbols used in the timing requirements and switching characteristics tables are created
in accordance with JEDEC Standard 100. To shorten the symbols, some of the pin names and other related
terminology have been abbreviated as follows:
Lowercase subscripts and their meanings:
56
Letters and symbols and their meanings:
a
access time
H
High
c
cycle time (period)
L
Low
d
delay time
V
Valid
dis
disable time
Z
High impedance
en
enable time
f
fall time
h
hold time
r
rise time
su
setup time
t
transition time
v
valid time
w
pulse duration (width)
X
Unknown, changing, or don’t care level
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.6
Clock Options
The frequency of the reference clock provided at the CLKIN pin can be divided by a factor of two or four to
generate the internal machine cycle. The selection of the clock mode is described in Section 3.2.6.
5.6.1 Divide-By-Two, Divide-By-Four, and Bypass Clock Options – PLL Disabled
The frequency of the reference clock provided at the CLKIN pin can be divided by a factor of two or four to
generate the internal machine cycle. The selection of the clock mode is described in Section 3.2.6.
Table 5–2 and Table 5–3 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5–2).
Table 5–2. Divide-By-Two, Divide-By-Four, and Bypass Clock Options Timing Requirements
tc(CI)
tf(CI)
Cycle time, CLKIN
tr(CI)
Rise time, CLKIN
tw(CIL)
Pulse duration, CLKIN low
MIN
MAX
20
†
ns
6
ns
6
ns
Fall time, CLKIN
UNIT
5
ns
tw(CIH) Pulse duration, CLKIN high
5
ns
† This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies
approaching 0 Hz.
Table 5–3. Divide-By-Two, Divide-By-Four, and Bypass Clock Options Switching Characteristics
PARAMETER
tc(CO)
tc(CO)
Cycle time, CLKOUT
td(CIH-CO)
tf(CO)
Delay time, CLKIN high to CLKOUT high/low
tr(CO)
tw(COL)
Rise time, CLKOUT
MIN
Cycle time, CLKOUT – bypass mode
TYP
MAX
†
ns
7.5
†
ns
2
7
11
ns
Fall time, CLKOUT
1
ns
1
Pulse duration, CLKOUT low
UNIT
2tc(CI)
2tc(CI)
7.5
H–2
ns
H–1
H
ns
tw(COH)
Pulse duration, CLKOUT high
H–2
H–1
H
ns
† This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies
approaching 0 Hz.
tr(CI)
tw(CIH)
tw(CIL)
tc(CI)
tf(CI)
CLKIN
tc(CO)
td(CIH-CO)
tw(COH)
tf(CO)
tr(CO)
tw(COL)
CLKOUT
Figure 5–2. External Divide-by-Two Clock Timing
December 1999 – Revised April 2002
SPRS122E
57
Electrical Specifications
5.6.2 Multiply-By-N Clock Option – PLL Enabled
The frequency of the reference clock provided at the CLKIN pin can be multiplied by a factor of N to generate
the internal machine cycle. The selection of the clock mode and the value of N is described in Section 3.2.6.
Table 5–4 and Table 5–5 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5–3).
Table 5–4. Multiply-By-N Clock Option Timing Requirements
Integer PLL multiplier N (N = 1–15)†
tc(CI)
MIN
20‡
MAX
20‡
20‡
100
PLL multiplier N = x.5†
Cycle time, CLKIN
PLL multiplier N = x.25, x.75†
tf(CI)
tr(CI)
UNIT
200
ns
50
Fall time, CLKIN
6
ns
Rise time, CLKIN
6
ns
tw(CIL) Pulse duration, CLKIN low
5
ns
tw(CIH) Pulse duration, CLKIN high
5
ns
† N = Multiplication factor
‡ The multiplication factor and minimum CLKIN cycle time should be chosen such that the resulting CLKOUT cycle time is within the specified range
(tc(CO))
Table 5–5. Multiply-By-N Clock Option Switching Characteristics
PARAMETER
MIN
MAX
7.5
TYP
tc(CI)/N†
2
7
11
tc(CO)
td(CI-CO)
Cycle time, CLKOUT
tf(CO)
tr(CO)
Fall time, CLKOUT
1.5
Rise time, CLKOUT
1.5
tw(COL)
tw(COH)
Pulse duration, CLKOUT low
H–2
H–1
Pulse duration, CLKOUT high
H–2
H–1
Delay time, CLKIN high/low to CLKOUT high/low
tp
Transitory phase, PLL lock up time
† N = Multiplication factor
tw(CIH)
tc(CI)
tw(CIL) tr(CI)
UNIT
ns
ns
ns
ns
H
ns
H
ns
45
ms
tf(CI)
CLKIN
td(CI-CO)
tc(CO)
tp
CLKOUT
tw(COH)
tf(CO)
tw(COL)
tr(CO)
Unstable
Figure 5–3. External Multiply-by-One Clock Timing
58
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.7
Reset, x_BIO, and Interrupt Timings
Table 5–6 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5–4 and
Figure 5–5).
Table 5–6. Reset, x_BIO, and Interrupt Timing Requirements
MIN
MAX
UNIT
th(RS)
th(BIO)
Hold time, x_RS after CLKOUT low
0
ns
Hold time, x_BIO after CLKOUT low
0
ns
th(INT)
tw(RSL)
Hold time, x_INT, x_NMI, after CLKOUT low†
Pulse duration, x_RS low‡§
0
ns
4H+4
ns
tw(BIO)
tw(INTH)
Pulse duration, x_BIO low, synchronous†
5H
ns
Pulse duration, x_INT, x_NMI high (synchronous)†
Pulse duration, x_INT, x_NMI low (synchronous)†
4H
ns
4H
ns
6
ns
4
ns
tw(INTL)
tw(INTL)WKP Pulse duration, x_INT, x_NMI low for IDLE2/IDLE3 wakeup†
tsu(RS)
Setup time, x_RS before CLKIN low§
tsu(BIO)
Setup time, x_BIO before CLKOUT low
7
ns
tsu(INT)
Setup time, x_INT, x_NMI, x_RS before CLKOUT low
7
ns
† The external interrupts (x_INT, x_NMI) are synchronized to the core CPU by way of a two flip-flop synchronizer, which samples these inputs with
consecutive falling edges of CLKOUT. The input to the interrupt pins is required to represent a 1-0-0 sequence at the timing that is corresponding
to a three-CLKOUT sampling sequence.
‡ If the PLL mode is selected, then at power-on sequence, or at wakeup from IDLE3, x_RS must be held low for at least 50 µs to ensure
synchronization and lock-in of the PLL.
§ x_RS can cause a change in clock frequency, changing the value of H (see Section 3.2.6).
CLKIN
tsu(RS)
tw(RSL)
x_RS, x_NMI, x_INT
tsu(INT)
th(RS)
CLKOUT
tsu(BIO)
th(BIO)
x_BIO
tw(BIO)
Figure 5–4. Reset and x_BIO Timings
December 1999 – Revised April 2002
SPRS122E
59
Electrical Specifications
CLKOUT
tsu(INT)
tsu(INT)
th(INT)
x_INT, x_NMI
tw(INTH)
tw(INTL)
Figure 5–5. Interrupt Timing
60
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.8
External Flag (x_XF), Timer (x_TOUT), and Watchdog Timer Output (x_WTOUT)
Timings
Table 5–7 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 5–6,
Figure 5–7, and Figure 5–8).
Table 5–7. External Flag (x_XF), Timer (x_TOUT), and Watchdog Timer Output (x_WTOUT)
Switching Characteristics
PARAMETER
MIN
MAX
Delay time, CLKOUT high to x_XF high
–1
4
Delay time, CLKOUT high to x_XF low
–1
6
td(TOUTH)
td(TOUTL)
Delay time, CLKOUT high to x_TOUT high
–1
4
ns
Delay time, CLKOUT high to x_TOUT low
–1
6
ns
tw(TOUT)
Pulse duration, x_TOUT
2H –8
2H
ns
td(WTOUTH)
td(WTOUTL)
Delay time, CLKOUT high to x_WTOUT high
–1
4
ns
–1
4
ns
tw(WTOUT)
Pulse duration, x_WTOUT
td(XF)
Delay time, CLKOUT high to x_WTOUT low
2H – 8
UNIT
ns
ns
CLKOUT
td(XF)
x_XF
Figure 5–6. External Flag (x_XF) Timing
CLKOUT
td(TOUTL)
td(TOUTH)
x_TOUT
tw(TOUT)
Figure 5–7. Timer (x_TOUT) Timing
CLKOUT
td(WTOUTL)
x_WTOUT
td(WTOUTH)
tw(WTOUT)
Figure 5–8. Watchdog Timer (x_WTOUT) Timing
December 1999 – Revised April 2002
SPRS122E
61
Electrical Specifications
5.9
General-Purpose Input/Output (GPIO) Timing
Table 5–8 and Table 5–9 assume testing over recommended operating conditions (see Figure 5–9).
Table 5–8. GPIO Timing Requirements
MIN
MAX
UNIT
tsu(GPIO-COH)
Setup time, x_GPIOn input valid before CLKOUT high, x_GPIOn configured as
general-purpose input.
8
ns
th(GPIO-COH)
Hold time, x_GPIOn input valid after CLKOUT high, x_GPIOn configured as
general-purpose input.
0
ns
Table 5–9. GPIO Switching Characteristics
PARAMETER
td(COH-GPIO)
Delay time, CLKOUT high to x_GPIOn output change. x_GPIOn configured as
general-purpose output.
MIN
MAX
UNIT
0
6
ns
CLKOUT
tsu(GPIO-COH)
th(GPIO-COH)
x_GPIOn Input Mode
td(COH-GPIO)
x_GPIOn Output Mode
Figure 5–9. GPIO Timings
62
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.10 Multichannel Buffered Serial Port Timing
5.10.1
McBSP0/1/2 Transmit and Receive Timings
The serial port timings that are referenced to CLKOUT are actually related to the internal CPU clock frequency.
These timings are not affected by the value of the DIVFCT bit field in the BSCR register (see Section 3.2.2.5
of this data manual for details on the BSCR register). Any references to CLKOUT in these timing parameters
refer to the CLKOUT timings when no divide factor is selected (DIVFCT = 00b).
Table 5–10 and Table 5–11 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5–10 and Figure 5–11).
Table 5–10. McBSP0/1/2 Transmit and Receive Timing Requirements†
MIN
tc(BCKRX)
tw(BCKRX)
Cycle time, x_BCLKR/X
BCLKR/X ext
Pulse duration, x_BCLKR/X low or x_BCLKR/X high
th(BCKRL-BFRH)
th(BCKRL-BDRV)
Hold time, external x_BFSR high after x_BCLKR low
th(BCKXL-BFXH)
tsu(BFRH-BCKRL)
tsu(BDRV-BCKRL)
tsu(BFXH-BCKXL)
MAX
UNIT
50
ns
BCLKR/X ext
24
ns
BCLKR ext
7.5
ns
Hold time, x_BDR valid after x_BCLKR low
BCLKR ext
7.5
ns
Hold time, external x_BFSX high after x_BCLKX low
BCLKX ext
7.5
ns
Setup time, external x_BFSR high before x_BCLKR low
BCLKR ext
7.5
ns
Setup time, x_BDR valid before x_BCLKR low
BCLKR ext
7.5
ns
Setup time, external x_BFSX high before x_BCLKX low
BCLKX ext
7.5
ns
tr(BCKRX)
Rise time, x_BCLKR/X
BCLKR/X ext
6
ns
tf(BCKRX)
Fall time, x_BCLKR/X
BCLKR/X ext
6
ns
† Polarity bits CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are
also inverted.
December 1999 – Revised April 2002
SPRS122E
63
Electrical Specifications
Table 5–11. McBSP0/1/2 Transmit and Receive Switching Characteristics†
PARAMETER
MIN
MAX
UNIT
td(BCKXH-BFXV)
Delay time, x_BCLKX high to internal x_BFSX valid
BCLKX ext
2
15
ns
tdis(BCKXH-BDXHZ)
Disable time, x_BCLKX high to x_BDX high impedance following last data
bit
BCLKX ext
1
18
ns
Delay time, x_BCLKX high to x_BDX valid. This applies to all bits except
the first bit transmitted.
BCLKX ext
4
20
Delay time, x_BCLKX high to x_BDX valid.‡
DXENA = 0
BCLKX ext
16
DXENA = 1
BCLKX ext
4H+19
DXENA = 0
BCLKX ext
2
DXENA = 1
BCLKX ext
4H+2
DXENA = 0
BFSX ext
17
DXENA = 1
BFSX ext
4H+15
td(BCKXH-BDXV)
Only
O
l applies
li to fifirst bi
bit transmitted
i d when
h iin D
Data D
Delay
l 1
or 2 (XDATDLY=01b or 10b) modes
Enable time, x_BCLKX high to x_BDX driven.‡
ten(BCKXH-BDX)
Only
O
l applies
li to fifirst bi
bit transmitted
i d when
h iin D
Data D
Delay
l 1
or 2 (XDATDLY=01b or 10b) modes
Delay time, x_BFSX high to x_BDX valid.‡
td(BFXH-BDXV)
Only
O
l applies
li to fifirst bi
bit transmitted
i d when
h iin D
Data D
Delay
l 0
(XDATDLY=00b) mode.
Enable time, x_BFSX high to x_BDX driven.‡
ns
ns
ns
DXENA = 0
BFSX ext
1
ns
Only
O
l applies
li to fifirst bi
bit transmitted
i d when
h iin D
Data D
Delay
l 0
DXENA = 1
BFSX ext
4H+5
(XDATDLY=00b) mode
† Polarity bits CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are
also inverted.
‡ See the TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals (literature number SPRU302) for a description of the DX enable
(DXENA) and data delay features of the McBSP.
ten(BFXH-BDX)
64
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
tc(BCKRX)
tw(BCKRXH)
tr(BCKRX)
tw(BCKRXL)
x_BCLKR
td(BCKRH–BFRV)
td(BCKRH–BFRV)
tr(BCKRX)
x_BFSR (int)
tsu(BFRH–BCKRL)
th(BCKRL–BFRH)
x_BFSR (ext)
th(BCKRL–BDRV)
tsu(BDRV–BCKRL)
x_BDR
(RDATDLY=00b)
Bit (n–1)
(n–2)
tsu(BDRV–BCKRL)
(n–3)
(n–4)
th(BCKRL–BDRV)
x_BDR
(RDATDLY=01b)
Bit (n–1)
(n–2)
tsu(BDRV–BCKRL)
(n–3)
th(BCKRL–BDRV)
x_BDR
(RDATDLY=10b)
Bit (n–1)
(n–2)
Figure 5–10. McBSP0/1/2 Receive Timings
tc(BCKRX)
tw(BCKRXH)
tw(BCKRXL)
tr(BCKRX)
tf(BCKRX)
x_BCLKX
td(BCKXH–BFXV)
td(BCKXH–BFXV)
x_BFSX (int)
tsu(BFXH–BCKXL)
th(BCKXL–BFXH)
x_BFSX (ext)
ten(BFXH–BDX)
x_BDX
(XDATDLY=00b)
Bit 0
td(BFXH–BDXV)
Bit (n–1)
td(BCKXH–BDXV)
(n–2)
ten(BCKXH–BDX)
x_BDX
(XDATDLY=01b)
(n–3)
td(BCKXH–BDXV)
Bit (n–1)
Bit 0
(n–2)
(n–3)
td(BCKXH–BDXV)
tdis(BCKXH–BDXHZ)
x_BDX
(XDATDLY=10b)
(n–4)
ten(BCKXH–BDX)
Bit 0
Bit (n–1)
(n–2)
Figure 5–11. McBSP0/1/2 Transmit Timings
December 1999 – Revised April 2002
SPRS122E
65
Electrical Specifications
5.10.2
McBSP0 General-Purpose I/O Timing
Table 5–12 and Table 5–13 assume testing over recommended operating conditions (see Figure 5–12).
Table 5–12. McBSP0 General-Purpose I/O Timing Requirements
MIN
tsu(BGPIO-COH)
th(COH-BGPIO)
Setup time, BGPIOx input mode before CLKOUT high†
Hold time, BGPIOx input mode after CLKOUT high†
MAX
UNIT
7
ns
0
ns
† BGPIOx refers to x_BCLKR, x_BFSR, x_BDR, x_BCLKX, or x_BFSX when configured as a general-purpose input.
Table 5–13. McBSP0 General-Purpose I/O Switching Characteristics
PARAMETER
MIN
td(COH-BGPIO)
Delay time, CLKOUT high to BGPIOx output mode‡
–8
‡ BGPIOx refers to x_BCLKR, x_BFSR, x_BCLKX, x_BFSX, or x_BDX when configured as a general-purpose output.
tsu(BGPIO-COH)
MAX
8
UNIT
ns
td(COH-BGPIO)
CLKOUT
th(COH-BGPIO)
BGPIOx Input
Mode†
BGPIOx Output
Mode‡
† BGPIOx refers to x_BCLKR, x_BFSR, x_BDR, x_BCLKX, or x_BFSX when configured as a general-purpose input.
‡ BGPIOx refers to x_BCLKR, x_BFSR, x_BCLKX, x_BFSX, or x_BDX when configured as a general-purpose output.
Figure 5–12. McBSP0 General-Purpose I/O Timings
66
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
5.11 Host-Port Interface (HPI16) Timing
Table 5–14 and Table 5–15 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 5–13 through Figure 5–19). In the following tables, DS refers to the logical OR of HCS, HDS1, and
HDS2, and HD refers to any of the HPI data bus pins (HD0, HD1, HD2, etc.).
Table 5–14. HPI16 Timing Requirements
MIN
MAX
UNIT
tsu(HBV-DSL)
th(DSL-HBV)
Setup time, HAD valid before DS falling edge†‡
Hold time, HAD valid after DS falling edge†‡
4
ns
4
ns
tsu(HBV-HSL)
th(HSL-HBV)
Setup time, HAD valid before HAS falling edge†
Hold time, HAD valid after HAS falling edge†
4
ns
4
ns
tsu(HAV-DSH)
tsu(HAV-DSL)
Setup time, address valid before DS rising edge (nonmultiplexed write)‡
Setup time, address valid before DS falling edge (nonmultiplexed read)‡
5
ns
–(4H + 5)
ns
th(DSH-HAV)
tsu(HSL-DSL)
Hold time, address valid after DS rising edge (nonmultiplexed mode)‡
Setup time, HAS low before DS falling edge‡
2
ns
4
ns
th(HSL-DSL)
tw(DSL)
Hold time, HAS low after DS falling edge‡
Pulse duration, DS low‡
2
ns
23
ns
tw(DSH)
Pulse duration, DS high‡
8
ns
tc(DSH-DSH)
Nonmultiplexed or multiplexed mode Reads
(no increment) memory accesses (or
writes to the FETCH bit) with no DMA
Writes
activity.
10H + 20
Nonmultiplexed or multiplexed mode Reads
Cycle time, DS rising edge to next DS (no increment) memory accesses (or
rising edge‡
writes to the FETCH bit) with 16-bit
Writes
DMA activity.
16H + 20
Nonmultiplexed or multiplexed mode Reads
(no increment) memory accesses (or
writes to the FETCH bit) with 32-bit
Writes
DMA activity.
24H + 20
Multiplexed
(autoincrement)
memory
accesses (or writes to the FETCH bit) with no
Cycle
y time, DS rising
g edge
g to next DS DMA activity.
rising
i i edge
d ‡
Multiplexed
(autoincrement)
memory
accesses (or writes to the FETCH bit) with
(In autoincrement mode, WRITE
16-bit DMA activity.
timings are the same as READ
Multiplexed
(autoincrement)
memory
timings.)
accesses (or writes to the FETCH bit) with
32-bit DMA activity.
ns
10H + 10
ns
16H + 10
ns
24H + 10
10H + 10
ns
16H + 10
ns
24H + 10
ns
Cycle time, DS rising edge to next DS rising edge for writes to DSPINT and x_HINT
8H
ns
Cycle time, DS rising edge to next DS rising edge for HPIC reads, HPIC XADD bit
writes, and address register reads and writes
40
ns
tsu(HDV-DSH)W
th(DSH-HDV)W
Setup time, HD valid before DS rising edge‡
4
ns
Hold time, HD valid after DS rising edge, write‡
2
ns
tsu(SELV-DSL)
th(DSH-SELV)
Setup time, HPI_SEL1/SEL2 valid before DS falling edge‡
Hold time, HPI_SEL1/SEL2 valid after DS rising edge‡
4
ns
1
ns
† HAD stands for HCNTL0, HCNTL1, and HR/W.
‡ DS refers to either HCS or HDS, whichever is controlling the transfer. Refer to the TMS320C54x DSP Reference Set, Volume 5: Enhanced
Peripherals (literature number SPRU302) for information regarding logical operation of the HPI16. These timings are shown assuming that HDS
is the signal controlling the transfer.
December 1999 – Revised April 2002
SPRS122E
67
Electrical Specifications
Table 5–15. HPI16 Switching Characteristics
PARAMETER
td(DSL-HDD) Delay time, DS low to HD driven†
Case 1a: Memory accesses initiated immediately following a write
when DMAC is active in 16-bit mode and tw(DSH) was < 18H
MIN
MAX
UNIT
3
20
ns
32H+20 – tw(DSH)
ns
16H+20 – tw(DSH)
ns
Case 1b: Memory accesses initiated by an autoincrement when
DMAC is active in 16-bit mode and tw(DSH) was < 18H
Case 1c: Memory accesses not initiated by an autoincrement (or not
immediately following a write) when DMAC is active in 16-bit mode
16H+20
ns
Case 1d: Memory accesses initiated by an autoincrement when
DMAC is active in 16-bit mode and tw(DSH) was ≥ 18H
Delay time, DS
low to HD valid
td(DSL-HDV1)
for first word of
an HPI read
20
Case 1e: Memory accesses initiated immediately following a write
when DMAC is active in 16-bit mode and tw(DSH) was < 26H
48H+20 – tw(DSH)
Case 1f: Memory access initiated by an autoincrement when DMAC
is active in 32-bit mode and tw(DSH) was < 26H
24H+20 – tw(DSH)
Case 1g: Memory access not initiated by an autoincrement (or not
immediately following a write) when DMAC is active in 32-bit mode
24H+20
Case 1h: Memory access initiated by an autoincrement when DMAC
is active in 32-bit mode and tw(DSH) was ≥ 26H
20H+20 – tw(DSH)
Case 2b: Memory accesses initiated by an autoincrement when
DMAC is inactive and tw(DSH) was < 10H
10H+20 – tw(DSH)
Case 2c: Memory accesses not initiated by an autoincrement (or not
immediately following a write) when DMAC is inactive
ns
20
Case 3: HPIC/HPIA reads
20
3
20
ns
10H+5
Memory accesses (or writes to the FETCH bit) with one or more
16-bit DMA channels active
16H+5
Memory accesses (or writes to the FETCH bit) with one or more
32-bit DMA channels active
24H+5
Writes to DSPINT and x_HINT‡
4H + 5
tv(HYH-HDV) Valid time, HD valid after HRDY high
th(DSH-HDV)R Hold time, HD valid after DS rising edge, read†
td(DSL-HYL) Delay time, DS low to HRDY low†
td(DSH-HYL) Delay time, DS high to HRDY low†
ns
10H+20
Case 2d: Memory accesses initiated by an autoincrement when
DMAC is inactive and tw(DSH) was ≥ 10H
high to HRDY
high†
td(DSH-HYH)
((writes
rites
and
autoincrement
reads)
ns
20
Case 2a: Memory accesses initiated immediately following a write
when DMAC is active in 16-bit mode and tw(DSH) was < 10H
td(DSL-HDV2) Multiplexed reads with autoincrement. Prefetch completed.
Memory accesses (or writes to the FETCH bit) when no DMA is
Delay time, DS active
ns
0
ns
6
ns
10
ns
18
ns
18
ns
td(HSL-HYL) Delay time, HAS low to HRDY low, read
18
ns
† DS refers to either HCS or HDS, whichever is controlling the transfer. Refer to the TMS320C54x DSP Reference Set, Volume 5: Enhanced
Peripherals (literature number SPRU302) for information regarding logical operation of the HPI16. These timings are shown assuming that
HDS is the signal controlling the transfer.
‡ HRDY does not go low for other register accesses.
68
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
HCS
tsu(HSL–DSL)
th(HSL–DSL)
HAS
tc(DSH–DSH)
tsu(HBV–HSL)
HDS
tw(DSH)
th(HSL–HBV)
tw(DSL)
HR/W
HCNTL[1:0]
01
01
td(DSL–HDV1)
th(DSH–HDV)R
td(DSL–HDV2)
Data 1
HD[15:0]
td(DSL–HDD)
PF Data
td(DSH–HYL)†
HRDY‡
td(HSL–HYL)
td(DSH–HYH)†
tv(HYH–HDV)
† HRDY goes low at these times only after autoincrement reads.
‡ While HCS is not selected, HRDY is in high-Z state.
Figure 5–13. Multiplexed Read Timings Using HAS
December 1999 – Revised April 2002
SPRS122E
69
Electrical Specifications
HCS
tsu(HBV–DSL)
tc(DSH–DSH)
HDS
th(DSL–HBV)
tw(DSH)
tw(DSL)
HR/W
01
HCNTL[1:0]
01
th(DSH–HDV)R
td(DSL–HDV1)
td(DSL–HDV2)
PF Data
Data 1
HD[15:0]
td(DSL–HDD)
td(DSH–HYL)†
HRDY‡
td(DSL–HYL)
td(DSH–HYH)†
tv(HYH–HDV)
† HRDY goes low at these times only after autoincrement reads.
‡ While HCS is not selected, HRDY is in high-Z state.
Figure 5–14. Multiplexed Read Timings With HAS Held High
70
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
HCS
tsu(HBV–HSL)
th(HSL–DSL)
HAS
tsu(HSL–DSL)
HR/W
th(HSL–HBV)
HCNTL[1:0]
01
01
tc(DSH–DSH)
HDS
tw(DSH)
tw(DSL)
tsu(HDV–DSH)W
HD[15:0]
Data 1
Data 2
th(DSH–HDV)W
HRDY†
td(DSH–HYL)
td(DSH–HYH)
† While HCS is not selected, HRDY is in high-Z state.
Figure 5–15. Multiplexed Write Timings Using HAS
December 1999 – Revised April 2002
SPRS122E
71
Electrical Specifications
HCS
tc(DSH–DSH)
tw(DSH)
HDS
tw(DSL)
tsu(HBV–DSL)
HR/W
th(DSL–HBV)
HCNTL[1:0]
01
01
tsu(HDV–DSH)W
th(DSH–HDV)W
Data 1
HD[15:0]
Data 2
td(DSH–HYL)
HRDY†
td(DSH–HYH)
† While HCS is not selected, HRDY is in high-Z state.
Figure 5–16. Multiplexed Write Timings With HAS Held High
72
SPRS122E
December 1999 – Revised April 2002
Electrical Specifications
HCS
tw(DSH)
tc(DSH–DSH)
HDS
tsu(HBV–DSL)
tsu(HBV–DSL)
th(DSL–HBV)
tw(DSL)
th(DSL–HBV)
HR/W
tsu(HAV–DSL)
th(DSH–HAV)
HA[18:0]
Valid Address
Valid Address
th(DSH–HDV)R
td(DSL–HDV1)
td(DSL–HDV1)
th(DSH–HDV)R
Data
HD[15:0]
td(DSL–HDD)
tv(HYH–HDV)
Data
td(DSL–HDD)
tv(HYH–HDV)
HRDY†
td(DSL–HYL)
† While HCS is not selected, HRDY is in high-Z state.
td(DSL–HYL)
Figure 5–17. Nonmultiplexed Read Timings
December 1999 – Revised April 2002
SPRS122E
73
Electrical Specifications
HCS
tw(DSH)
tc(DSH–DSH)
HDS
tsu(HBV–DSL)
tsu(HBV–DSL)
th(DSL–HBV)
th(DSL–HBV)
HR/W
tsu(HAV–DSH)
tw(DSL)
th(DSH–HAV)
Valid Address
HA[18:0]
Valid Address
tsu(HDV–DSH)W
tsu(HDV–DSH)W
th(DSH–HDV)W
th(DSH–HDV)W
Data Valid
HD[15:0]
Data Valid
td(DSH–HYH)
HRDY†
td(DSH–HYL)
† While HCS is not selected, HRDY is in high-Z state.
Figure 5–18. Nonmultiplexed Write Timings
HCS
tsu(SELV1–DSL)
th(DSH–SELV1)
HPI_SEL1
tsu(SELV2–DSL)
th(DSH–SELV2)
HPI_SEL2
HDS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Figure 5–19. HPI_SEL1 and HPI_SEL2 Timing
74
SPRS122E
December 1999 – Revised April 2002
Mechanical Data
6
Mechanical Data
6.1
Ball Grid Array Mechanical Data
GGU (S-PBGA-N169)
PLASTIC BALL GRID ARRAY
12,10
SQ
11,90
9,60 TYP
0,80
0,80
N
M
L
K
J
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8 9 10 11 12 13
0,95
0,85
1,40 MAX
Seating Plane
0,12
0,08
0,55
0,45
0,08 M
0,45
0,35
0,10
4073221-3/B 08/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. MicroStar BGA configuration
Figure 6–1. TMS320VC5441 169-Ball MicroStar BGA Plastic Ball Grid Array (GGU) Package
MicroStar BGA is a trademark of Texas Instruments.
December 1999 – Revised April 2002
SPRS122E
75
Mechanical Data
6.2
Low-Profile Quad Flatpack Mechanical Data
PGF (S-PQFP-G176)
PLASTIC QUAD FLATPACK
132
89
88
133
0,27
0,17
0,08 M
0,50
0,13 NOM
176
45
1
44
Gage Plane
21,50 SQ
24,20
SQ
23,80
26,20
SQ
25,80
0,25
0,05 MIN
0°–ā7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040134 / B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
Figure 6–2. TMS320VC5441 176-Pin Low-Profile Quad Flatpack (PGF) Package
76
SPRS122E
December 1999 – Revised April 2002