MICROCIRCUIT DATA SHEET Original Creation Date: 06/24/98 Last Update Date: 04/20/01 Last Major Revision Date: 06/07/99 MNCLC414A-X REV 1A0 QUAD, LOW-POWER MONOLITHIC OP AMP General Description The CLC414 is a low-power, quad, monolithic operational amplifier designed for intermediate-gain applications where power and cost per channel are of primary concern. Benefiting from Comlinear's current feedback architecture, the CLC414 offers a gain range of +1 to +10 while providing stable, oscillation-free operation without external compensation, even at unity gain. Operating from +5V supplies, the CLC414 consumes only 25mV of power per channel, yet maintains a 90MHz small-signal bandwidth and a 1000V/uS slew rate. The CLC414 also provides wide channel isolation with its 70dB crosstalk (input referred at 5MHz). Applications requiring a high-density solution to high-speed amplification such as active filters and instumenation differential amplifiers will benefit from the CLC414's four integrated, wideband operational amplifiers in one 14-pin package. Commercial remote-sensing applications and battery-powered radio transceivers requiring high-performance, low-power amplifiers will find the CLC414 to be an attractive, cost-effective solution. In composite video switching and distribution applications, the CLC414 offers differential gain and phase performance of 0.1%, 0.12 degrees at 3.58MHz. The lower power CLC414 and the wideband CLC415 are quad versions of the CLC406. Both of these quads afford the designer lower power consumption and lower cost per channel with the additional benefit of requiring less board space per amplifier. Industry Part Number NS Part Numbers CLC414A CLC414AE-QML** CLC414AJ-QML* Prime Die UB1563A Controlling Document 5962-9169301MCA*, M2A** Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Features - 90MHz small signal bandwidth 2mA quiescent current per amplifier 70dB channel isolation @ 5MHz 0.1%/0.12 degrees differential gain/phase 16ns settling to 0.1% 100V/uS slew rate 3.3ns rise and fall time (2 Vpp) 70mA output current Applications - Composite video distribution amplifiers HDTV amplifiers RGB-video amplifiers CCD signal processing Active filters Instumentation diff. amplifiers General purpose high density requirements 2 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vs) +7V dc Output Current (Iout) 70mA Common Mode Input Voltage (Vcm) +Vs Differential Input Voltage (Vid) +10V Power Dissipation (Pd) (Note 2) Lead Temperature (soldering, 10 seconds) 1.2W +300 C Junction Temperature (Tj) +175 C Storage Temperature Range -65 C to +150 C Thermal Resistance Junction-to-ambient (ThetaJA) Ceramic DIP (Still Air) (500 LFPM) LCC (Still Air) (500 LFPM) Junction-to case (ThetaJC) Ceramic DIP LCC Package Weight (typical) Ceramic DIP LCC ESD Tolerance (Note 3) 94 C/W 57 C/W TBD TBD 17 C/W TBD 2190mg TBD 500V Note 1: Note 2: Note 3: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is functional, but do not guarantee specific perfomance limits. For guaranteed specifications and test conditions see the Electrical Characterisitics. The guaranteed specifications apply only for the test conditions listed. Some performance charateristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA) /ThetaJA or the number given in the absolute Maximum Ratings, whichever is lower. Human body model, 100pF discharged through 1.5k Ohms. 3 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Recommended Operating Conditions Supply Voltage (Vs) +5V dc Gain Range (Av) +1 to +10 Ambient Operating Temperature Range (Ta) -55 C to +125 C 4 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Electrical Characteristics AC/DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +5V dc, Av = +6, load resistance (Rl) = 100 Ohms, feedback resistance (Rf) = 500 Ohms, and gain resistance (Rg) = 100 Ohms. -55 C < Ta < +125 C (Note 3) SYMBOL +Iin -Iin Vio Tc (+Iin) PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Input Bias Current (noninverting) -5 +5 uA 1, 2 -10 +10 uA 3 Input Bias Current (inverting) -6 +6 uA 1 -10 +10 uA 2 -20 +20 uA 3 -6.0 +6.0 mV 1 -14.0 +14.0 mV 2 -10.5 +10.5 mV 3 Input Offset Voltage Rs = 50 Ohms Average +Input Bias Current Drift 1 -30 +30 nA/C 2 1 -75 +75 nA/C 3 Average -Input Bias Current Drift 1 -75 +75 nA/C 2 1 -175 +175 nA/C 3 Tc (Vio) Average Input Offset Voltage Drift 1 -80 +80 uV/C 2, 3 Is Supply Current (all channels) +11.5 mA +Rin Input Resistance (noninverting) Tc (-Iin) Iout PSRR CMRR SSBW LSBW No Load Output Current Power Supply Rejection Ratio Common Mode Rejection Ratio Small Signal Bandwidth Large Signal Bandwidth +Vs = +4.5V to +5.0V, -5.0V -Vs = -4.5V to Vcm = +1V 1 1000 KOhms 1, 2 1 500 KOhms 3 1 50 mA 1, 2 1 30 mA 3 2 46 dB 1, 3 2 44 dB 2 1 45 dB 4, 6 1 43 dB 5 60 MHz 4 2 41 MHz 5 2 60 MHz 6 1 40 MHz 4 1 35 MHz 5, 6 -3dB bandwidth, Vout < 2.0 Vpp -3dB bandwidth, Vout < 5.0 Vpp 5 1, 2, 3 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Electrical Characteristics AC/DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +5V dc, Av = +6, load resistance (Rl) = 100 Ohms, feedback resistance (Rf) = 500 Ohms, and gain resistance (Rg) = 100 Ohms. -55 C < Ta < +125 C (Note 3) SYMBOL GFPL GFPH GFR HD2 HD3 SNF PARAMETER Gain Flatness Peaking Low Gain Flatness Peaking High Gain Flatness Rolloff Second Harmonic Distortion Third Harmonic Distortion Total Noise Floor CONDITIONS NOTES At 0.1MHz to 15MHz, Vout < 2.0 Vpp VN ICN INN LPD Total Integrated Noise Input Noise Non-inverting Voltage Input Noise Inverting Current dB 5, 6 0.3 dB 4, 6 0.3 dB 5, 6 1.0 dB 4 2 1.6 dB 5 2 1.0 dB 6 -41 dBc 4 -37 dBc 5 -41 dBc 6 -47 dBc 4 -45 dBc 5 -47 dBc 6 -153 dBm 4, 6 -152 1Hz dBm 5 1 44 1Hz uV 1, 3 1 48 uV 2 1 5.0 nV/Sq 1, 3 1 5.5 RtHz nV/Sq 2 1 11.8 RtHz pA/Sq 1, 3 1 13 RtHz pA/Sq 2 1 1.6 RtHz pA/Sq 1, 3 1 1.8 RtHz pA/Sq 2 1 1.2 RtHz Degre 4, 6 1 1.5 es Degre 5 2 Vpp at 5MHz 1 Input Noise Non-inverting Current Linear Phase Deviation At > 1MHz At > 1MHz At 0.1MHz to 30MHz es 6 SUBGROUPS 0.15 2 Vpp at 5MHz At > 1MHz UNIT 4 At 0.1MHz to 30MHz, Vout < 2.0 Vpp At 1MHz to 75MHz MAX dB 1 INV MIN 0.15 At > 15MHz, Vout < 2.0 Vpp At > 1MHz PINNAME MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Electrical Characteristics AC/DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +5V dc, Av = +6, load resistance (Rl) = 100 Ohms, feedback resistance (Rf) = 500 Ohms, and gain resistance (Rg) = 100 Ohms. -55 C < Ta < +125 C (Note 3) SYMBOL DG1 DG2 DP1 DP2 XT CXT +Vout -Vout PARAMETER Differential Gain Differential Gain Differential Phase Differential Phase Crosstalk Crosstalk Output Voltage Swing Output Voltage Swing Cin Input Capacitance (noninverting) Ro Output Impedance CONDITIONS NOTES At 3.58MHz, Rl = 150Ohms, Av = +2 At 4.43MHz, Rl = 150Ohms, Av = +2 At 3.58MHz, Rl = 150Ohms, Av = +2 At 4.43MHz, Rl = 150Ohms, Av = +2 At 5MHz At 5MHz Rl = 100Ohms Rl = 100Ohms At DC 7 PINNAME MIN MAX UNIT SUBGROUPS 1 0.20 % 4 1 0.25 % 5 1 0.15 % 6 1 0.25 % 4 1 0.30 % 5 1 0.20 % 6 1 0.20 Degre 4 1 0.50 es Degre 5 1 0.15 es Degre 6 1 0.25 es Degre 4 1 0.60 es Degre 5 1 0.20 es Degre 6 1, 4 58 es dB 4, 6 1, 4 56 dB 5 1, 5 63 dB 4, 6 1, 5 61 dB 5 2 +2.6 V 4 2 +2.7 V 5 2 +2.5 V 6 2 -2.6 V 4 2 -2.7 V 5 2 -2.5 V 6 1 2.0 pF 4, 5, 6 1 0.3 Ohms 4 1 0.2 Ohms 5 1 0.6 Ohms 6 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Electrical Characteristics AC/DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +5V dc, Av = +6, load resistance (Rl) = 100 Ohms, feedback resistance (Rf) = 500 Ohms, and gain resistance (Rg) = 100 Ohms. -55 C < Ta < +125 C (Note 3) SYMBOL CMIR SR TRS TRL Ts PARAMETER CONDITIONS NOTES Common Input Voltage Range Slew Rate Rise and Fall Time Rise and Fall Time Settling Time Measured +1V with +3V Step 2V Step 5V Step 2V Step at 0.1 percent of the fixed value 2V Step at 0.02 percent of the fixed value OS Overshoot Note 1: Note 2: Note 3: Note 4: Note 5: 2V Step PINNAME UNIT MAX 1 -2.0 +2.0 V 4, 5 1 -1.4 +1.4 V 6 1 650 V/uS 4, 6 1 490 V/uS 5 1 5.0 nS 9, 11 1 6.5 nS 10 1 6.0 nS 9 1 7.0 nS 10, 11 1 24 nS 9, 11 1 30 nS 10 1 80 nS 9, 11 1 100 nS 10 1 10 % 9, 10, 11 If not tested, shall be guaranteed to the limits specified in table Group A testing only. The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. Three channels are driven simultaneously while observing the output of the undriven fourth channel. One channel is driven with a 2 Vpp pulse while the output of the most affected channel is observed. 8 SUBGROUPS MIN MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Graphics and Diagrams GRAPHICS# DESCRIPTION 07066HRA2 CERDIP (J), 14 LEAD (B/I CKT) 07072HRA2 LCC (E), TYPE C, 20 TERMINAL (B/I CKT) E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J14ARH CERDIP (J), 14 LEAD (P/P DWG) P000424A CERDIP (J), 14 LEAD (PINOUT) P000455A LCC (E), TYPE C, 20 TERMINAL (PIN OUT) See attached graphics following this page. 9 OUT1 1 14 OUT4 -IN1 2 13 -IN4 +IN1 3 12 +IN4 V+ 4 11 V- +IN2 5 10 +IN3 -IN2 6 9 -IN3 OUT2 7 8 OUT3 CLC414J 14 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000424A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 IN-1 OUT1 IN+1 4 N/C 3 2 N/C 1 OUT4 20 IN-4 19 18 IN+4 5 17 N/C V+ 6 16 V- N/C 7 15 N/C IN+2 8 14 IN+3 9 10 11 IN-2 OUT2 N/C 12 13 OUT3 IN-3 CLC414E 20 - LEAD LCC CONNECTION DIAGRAM TOP VIEW P000455A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 MICROCIRCUIT DATA SHEET MNCLC414A-X REV 1A0 Revision History Rev ECN # Originator Changes 0A0 M0002940 04/20/01 Rel Date Shaw Mead Initial MDS Release 1A0 M0003800 04/20/01 Shaw Mead Changed SSBW limit from 45MHz to 41MHz at 125'C Changed GRF limit from 1.5dB to 1.6dB at 125'C 10