ETC CLC411AJ-QML

MICROCIRCUIT DATA SHEET
Original Creation Date: 02/11/99
Last Update Date: 11/04/99
Last Major Revision Date: 05/06/99
MNCLC411A-X REV 0A0
High-Speed Video Op Amp with Disable
General Description
The Comlinear CLC411 combines a state-of-the-art complementary bipolar process with
Comlinear's patented current-feedback architecture to provide a very high-speed op amp
operating from +15V supplies. Drawing only 11mA quiescent current, the CLC411 provides a
200MHz small signal bandwidth and a 2300V/us slew rate while delivering a continuos 70mA
current output with +4.5V output swing. The CLC411's high-speed performance includes a
15ns settling time to 0.1%(2V step) and a 2.3ns rise and fall time (6V step).
The CLC411 is designed to meet the requirements of professional broadcast video systems
including composite video and high definition television. The CLC411 exceeds the HDTV
standard for gain flatness to 30MHz with it's +0.05dB flat frequency response and exceeds
composite video standards with its very low differential gain and phase errors of 0.02%,
0.03Degrees. The CLC411 is the op amp of choice for all video systems requiring upward
compatibility from NTSC and PAL to HDTV.
The CLC411 features a very fast disable/enable (10ns/55ns) allowing the multiplexing of
high-speed signals onto an analog bus through the common output connections of multiple
CLC411's. Using the same signal source to drive disable/enable pins is easy since
"break-before-make" is guaranteed.
Industry Part Number
NS Part Numbers
CLC411A
CLC411AJ-QML
Prime Die
UB1590C
Controlling Document
5962-9456601MPA
Processing
Subgrp Description
1
2
3
4
5
6
7
8A
8B
9
10
11
MIL-STD-883, Method 5004
Quality Conformance Inspection
MIL-STD-883, Method 5005
1
Static tests at
Static tests at
Static tests at
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
Temp ( oC)
+25
+125
-55
+25
+125
-55
+25
+125
-55
+25
+125
-55
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Features
-
200MHz small signal bandwidth (1Vpp)
+0.05dB gain flatness to 30MHz
0.02%, 0.03Degrees differential gain, phase
2300V/us slew rate
10ns disable to high-impedance output
70mA continuous output current
+4.5V output swing into 100 Ohm load
+4.0V input voltage range
Applications
-
HDTV amplifier
Video line driver
High-speed analog bus driver
Video signal multiplexer
DAC output buffer
2
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
(Absolute Maximum Ratings)
Supply Voltage (Vs)
(Note 1)
+18 V dc
Output current (Iout)
125 mA
Maximum Power dissipation (Pd)
(Note 2)
1.34W
Junction temperature (Tj)
+175C
Lead temperature (soldering, 10 seconds)
+300C
Differential input voltage (Vid)
+15 V
Common mode input voltage (Vcm)
+Vs
Storage temperature range
-65C to +150C
Thermal Resistance
ThetaJA
Ceramic DIP
Ceramic DIP
(Still Air )
(500LF/Min Air Flow)
97 C/W
59 C/W
ThetaJC
Package Weight
(typical)
Ceramic DIP
ESD Tolerance
(Note 3)
ESD Rating
Note 1:
Note 2:
Note 3:
20 C/W
TBD
1000V
Absolute Maximum Ratings are limits beyond which damage to the device may occur.
Operating Ratings are conditions for which the device is functional, but do not
guarantee specific performance limits. For guaranteed specifications and test
conditions see the Electrical Characteristics. The guaranteed specifications apply
only for the test conditions listed. Some performance characteristics may degrade
when the device is not operated under the listed test conditions.
The maximum power dissipation must be derated at elevated temperatures and is
dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to
ambient thermal resistance), and TA (ambient temperature). The maximum allowable
power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number
given in the Absolute Maximum Ratings, whichever is lower.
Human body model, 100pF discharged through 1.5K Ohms.
3
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Recommended Operating Conditions
Supply Voltage (Vs)
+15Vdc
Gain Range (Av)
+10 to +1000V/V
Ambient Operating Temperature Range (TA)
-55 C to +125 C
4
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Electrical Characteristics
Static and dc tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
SYMBOL
+Iib
-Iib
Vio
+Dib
PARAMETER
CONDITIONS
Input bias
current
Average input
bias current
drift
Ta = +125C,
DVio
Average input
offset voltage
drift
Ta = +125C, -55C
Icc
Supply current
No load
Iccd
PSRR
CMRR
Supply current
Power supply
rejection ratio
Common mode
rejection ration
-55C
-55C
MIN
5
SUBGROUPS
1
-20
20
uA
2
0
65
uA
3
-30
30
uA
1, 2
-40
40
uA
3
-9
9
mV
1
-14
14
mV
2
-13
13
mV
3
1
-250
250
nA/C 2
1
-400
400
nA/C 3
1
-150
150
nA/C 2
1
-200
200
nA/C 3
1
-50
50
uV/C 2, 3
12
mA
1, 2
14
mA
3
3.5
mA
1
4.5
mA
2, 3
50
dB
1
48
dB
2, 3
1
46
dB
4
1
44
dB
5, 6
-Vs = -4.5 V
Vcm = +1 V
UNIT
uA
Disable
+Vs = +4.5 V to +5.0 V,
to -5.0 V
MAX
30
Input offset
voltage
Ta = +125C,
PINNAME
0
Input bias
current
Average input
bias current
drift
-Dib
NOTES
(note 3)
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Electrical Characteristics
Frequeuncy domain tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
SYMBOL
SSBW
LSBW
GFPH
PARAMETER
Small signal
bandwith
Large signal
bandwith
Gain flatness
peaking high
CONDITIONS
NOTES
-3 dB bandwidth, Vout < 1.0 Vpp
-3 dB bandwidth,
Vout < 6.0 Vpp
GFRL
GFRH
LPD
Gain flatness
peaking low
Gain flatness
rolloff Low
Gain flatness
rolloff High
Linear phase
deviation
UNIT
SUBGROUPS
4
2
110
MHz
5
2
150
MHz
6
1
50
MHz
4, 6
1
40
MHz
5
0.5
dB
4
0.6
dB
5, 6
0.2
dB
4
2
0.3
dB
5
2
0.2
dB
6
0.2
dB
4
2
0.4
dB
5
2
0.2
dB
6
0.4
dB
4
2
0.7
dB
5, 6
1
1.0
Deg
4, 5,
6
0.1 MHz to 30 MHz, Vout < 1.0 Vpp
0.1 MHz to 30 MHz, Vout < 1.0 Vpp
0.1 MHz to 60 MHz, Vout < 1.0 Vpp
Vout < 1.0 Vpp
MAX
MHz
0.1 MHz to 200 MHz, Vout < 1.0 Vpp
0.1 MHz to 60 MHz,
MIN
150
2
GFPL
PINNAME
(note 3)
Distortion and noise tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
HD2
Second harmonic
distortion
2 Vpp at 20 MHz
-35
dBc
4
-35
dBc
5, 6
-42
dBc
4
2
-35
dBc
5
2
-42
dBc
6
2
HD3
Third harmonic
distortion
2 Vpp at 20 MHz
6
(note 3)
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Electrical Characteristics
Timing tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
SYMBOL
Ts
OS
PARAMETER
Settling time
Overshoot
CONDITIONS
NOTES
2 V step at 0.1% of the fixed value
2.0 V step
PINNAME
MIN
MAX
(note 3)
UNIT
SUBGROUPS
1
18
ns
9
1
23
ns
10, 11
1
10
%
9
1
15
5
10, 11
Miscellaneous performance tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
Rin
Input Resistance
Cin
Input capacitance
Vout
Output voltage
range
No load,
Voutl
Output voltage
range
CMIR
Common mode input
voltage range
Iout
Output current
1
750
kOhms 1
1
1000
kOhms 2
1
250
kOhms 3
1
Ta = +25C
(note 3)
3
pF
1, 2,
3
1
-4.5
4.5
V
1
Rl = 100Ohms, Ta = +25C
1
-4.0
4.0
V
1
Ta = +25C
1
-3.5
3.5
V
1
1
50
mA
1
1
40
mA
2
1
30
mA
3
Disable and enable tests.
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: Vs = +15 V dc, Av = +2, Rl = 100 Ohms, Rf = 300 Ohms, Rg = 300 Ohms, -55C < Ta < +125 C
Toff
Disable time
To > 50 dB attenuation at 10 MHz
(note 3)
1
30
ns
9, 11
1
60
ns
10
3.0
V
1, 2,
3
Vdis
Voltage at /DIS
pin to disable
1
Ven
Voltage at /DIS
pin to enable
1
6.5
V
1, 2
1
7.0
V
3
dB
4, 5,
6
OSD
Off isolation
Note 1:
Note 2:
At 10 MHz
1
If not tested, shall be guaranteed to the limits specified.
Group A testing only.
7
55
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
(Continued)
Note 3:
The algebraic convention, whereby the most negative value is a minimum and the most
positive is a maximum, is used in this table. Negative current shall be defined as
conventional current flow out of a device terminal.
8
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Graphics and Diagrams
GRAPHICS#
DESCRIPTION
07087HRA2
CERDIP (J), 8 LEAD (B/I CKT)
J08ARL
CERDIP (J), 8 LEAD (P/P DWG)
P000417A
CERDIP (J), 8 LEAD (PINOUT)
See attached graphics following this page.
9
+Vr
1
8
DIS
VINV
2
7
+VCC
VNON-INV
3
6
VOUT
4
5
-Vr
-VCC
CLC411J
8 - LEAD DIP
CONNECTION DIAGRAM
TOP VIEW
P000417A
N
MIL/AEROSPACE OPERATIONS
2900 SEMICONDUCTOR DRIVE
SANTA CLARA, CA 95050
MICROCIRCUIT DATA SHEET
MNCLC411A-X REV 0A0
Revision History
Rev
ECN #
0A0
M0003592 11/04/99
Rel Date
Originator
Changes
Shaw Mead
Initial MDS Release
10