HT1647 4-Level Gray Scale 64´16 LCD Controller for I/O mC Features · · · · · · · · · · · · · Operating voltage: 2.7V~5.2V Built-in 32kHz RC oscillator External 32.768kHz crystal oscillator or 32kHz frequency source input Standby current: < 1mA at 3V, < 2mA at 5V Internal resistor type: 1/5 bias or 1/4 bias, 1/16 duty Two selectable LCD frame frequencies: 89Hz or 170Hz Max. 64´16 patterns, 64 segments and 16 commons Built-in bit-map display RAM: 2048 bits (=64´16´2 bits) Built-in internal resistor type bias generator Six-wire interface (four data wires) Eight kinds of time base/WDT selection Time base or WDT overflow output R/W address auto increment · · Built-in buzzer driver (2kHz/4kHz) Power down command reduces power consumption Software configuration feature Data mode and Command mode instructions Three data accessing modes Provides VLCD pin to adjust LCD operating voltage Provides three kinds of bias current programming Control of TN-type, STN-type LCDs and ECB-type LCDs Four-level gray scale output for TN-type, STN-type LCDs panel Four-color output for ECB-type LCDs panel 100-pin QFP and in chip form · · · Cellular phone Global positioning system Consumer electronics · · · · · · · · · Applications · · · Leisure products Games Personal digital assistant General Description can support 4-color display as well as 4-level gray scale display. It displays 4-level gray scale output when the HT1647 drives a TN-type, STN-type LCDs. It displays four color output when the HT1647 drives an ECB-type. HT1647 uses PWM (Pulse Width Modulation) technique. The software configuration feature of the HT1647 make it suitable for multiple LCD applications including LCD modules and display subsystems. Only six lines (CS, WR, DB0~DB3) are required for the interface between the host controller and the HT1647. HT1647 is a peripheral device specially designed for I/O type mC used to expand the display capability. The max. display segment of the device are 1024 patterns (64 segments and 16 commons). It also supports four data bits interface, buzzer sound, Watchdog Timer or time base timer functions. The HT1647 is a memory mapping and multi-function LCD controller. Since the HT1647 can control ECB-type (Electrically Controlled Birefringence) LCDs in addition to current TN-type (Twisted Nematic) or STN-type (Super Twisted Nematic) LCDs, it Rev. 1.00 1 June 1, 2001 HT1647 Block Diagram O S C O D is p la y R A M O S C I C S R D W R D B 0 C o n tro l & T im in g C ir c u it C O M 0 L C D D r iv e r / B ia s C ir c u it C O M 1 5 S E G 0 D B 3 S E G 6 3 V D D V L C D V S S B Z B Z N o te : C B W D C IR Rev. 1.00 T o n e F re q u e n c y G e n e ra to r S : C h ip s Z , B Z : T o R , R D : W B 0 ~ D B 3 : O M 0 ~ C O Q : T im e W a tc h d o g T im e r & T im e B a s e G e n e r a to r IR Q e le c tio n n e o u tp u ts R IT E c lo c k , R E A D c lo c k D a ta b u s M 1 5 , S E G 0 ~ S E G 6 3 : L C D o u tp u ts b a s e o r W D T o v e r flo w o u tp u t 2 June 1, 2001 HT1647 Pin Assignment S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G 1 0 0 1 4 4 4 5 4 6 4 7 4 8 4 9 5 0 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 6 0 6 1 6 2 6 3 C S R D W R D B 0 D B 1 D B 2 D B 3 V S S O S C I O S C O V D D V L C D IR Q B Z B Z T 1 T 2 T 3 T 4 N C C O M 0 C O M 1 C O M 2 C O M 3 C O M 4 C O M 5 C O M 6 C O M 7 C O M 8 C O M 9 8 1 8 0 H T 1 6 4 7 1 0 0 Q F P -A 5 1 5 0 3 0 3 1 S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G 4 3 4 2 4 1 4 0 3 9 3 8 3 7 3 6 3 5 3 4 3 3 3 2 3 1 3 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 1 9 1 8 1 7 1 6 1 5 1 4 S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G S E G C O M C O M C O M C O M C O M C O M 1 3 1 2 1 1 1 0 9 8 7 6 1 5 1 4 3 5 4 3 2 1 0 1 3 1 2 1 1 1 0 Rev. 1.00 June 1, 2001 HT1647 Pad Assignment 1 4 S E G 5 6 1 5 S E G 5 7 1 6 S E G 5 8 1 7 S E G 5 9 1 8 S E G 6 0 1 9 S E G 6 1 2 0 S E G 6 2 2 1 S E G 6 3 2 2 S E G 1 7 S E G 5 5 S E G 1 8 1 3 S E G 1 9 S E G 5 4 S E G 2 0 1 2 S E G 2 1 S E G 5 3 S E G 2 2 1 1 S E G 2 3 S E G 5 2 S E G 2 4 1 0 S E G 2 5 S E G 5 1 S E G 2 6 S E G 5 0 9 S E G 2 7 8 S E G 2 8 S E G 4 9 S E G 2 9 7 S E G 3 0 S E G 4 8 S E G 3 1 6 S E G 3 2 S E G 4 7 S E G 3 3 S E G 4 6 5 S E G 3 4 4 S E G 3 5 S E G 4 5 S E G 3 6 3 S E G 3 7 S E G 4 4 S E G 3 8 2 S E G 3 9 S E G 4 3 S E G 4 0 1 S E G 4 1 S E G 4 2 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1 8 0 7 9 7 8 7 7 7 6 7 5 (0 , 0 ) 2 6 2 7 2 8 2 9 3 0 3 1 3 2 3 3 3 4 3 6 3 7 3 8 3 9 4 0 S E G 1 1 6 8 S E G 1 0 6 7 S E G 9 6 6 S E G 8 6 5 S E G 7 6 4 S E G 6 6 3 S E G 5 6 2 S E G 4 6 1 S E G 3 6 0 S E G 2 5 9 S E G 1 5 8 S E G 0 5 7 C O M 1 5 5 6 C O M 1 4 5 5 C O M 1 3 5 4 C O M 1 2 5 3 C O M 1 1 5 2 C O M 1 0 5 1 C O M 9 5 0 C O M 8 4 1 4 3 4 4 4 5 4 6 4 7 4 8 4 9 C O M 6 C O M 7 T 4 T 3 T 2 T 1 B Z B Z IR Q V L C D V D D O S C O O S C I V S S D B 3 D B 2 D B 1 D B 0 4 2 C O M 5 2 5 S E G 1 2 6 9 C O M 4 W R 3 5 S E G 1 3 7 0 C O M 3 2 4 S E G 1 4 7 1 C O M 2 R D S E G 1 5 7 2 C O M 1 2 3 S E G 1 6 C O M 0 C S 7 4 7 3 2 Chip size: 3865 ´ 3770 (mm) * The IC substrate should be connected to VSS in the PCB layout artwork. Rev. 1.00 4 June 1, 2001 HT1647 Pad Coordinates Unit: mm Pad No. X Y Pad No. X Y Pad No. X Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 -1774.50 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1779.30 -1690.00 -1690.00 -1690.00 -1430.20 -1294.80 -1149.50 -1013.90 -872.80 -738.30 -600.10 -465.60 1708.30 1409.80 1281.80 1150.00 1022.00 890.20 762.20 630.40 502.40 370.60 242.60 110.80 -17.20 -149.00 -277.00 -408.80 -536.80 -668.60 -796.60 -928.80 -1056.80 -1189.00 -1375.40 -1515.40 -1651.00 -1599.90 -1599.90 -1599.90 -1599.90 -1600.00 -1600.00 -1600.00 -1600.00 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 -331.40 -194.50 -48.00 87.40 235.20 383.40 530.40 678.60 875.00 1003.00 1134.80 1262.80 1394.60 1522.60 1654.40 1782.40 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 -1600.00 -1558.30 -1600.00 -1600.00 -1600.00 -1600.00 -1600.00 -1600.00 -1712.30 -1712.30 -1712.30 -1712.30 -1712.30 -1712.30 -1712.30 -1712.30 -1411.10 -1283.10 -1151.30 -1023.30 -891.50 -763.50 -631.70 -503.70 -371.90 -243.90 -112.10 15.90 147.70 275.70 407.50 535.50 667.30 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1775.70 1471.10 1343.10 1211.30 1083.30 951.50 823.50 691.70 563.70 431.90 303.90 172.10 44.10 -87.70 -215.70 -347.50 -475.50 -607.30 -735.30 -867.10 -995.10 -1126.90 -1254.90 -1386.70 -1514.70 -1646.50 795.30 927.10 1055.10 1186.90 1314.90 1446.70 1574.70 1706.50 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 1708.30 Rev. 1.00 5 June 1, 2001 HT1647 Pad Description Pad No. 23 Pad Name CS I/O Description I Chip selection input with pull-high resistor. When the CS is logic high, the data and command read from or write to the HT1647 are disabled. The serial interface circuit is also reset. But if the CS is at a logic low level and is input to the CS pad, the data and command transmission between the host controller and the HT1647 are all enabled. 24 RD I READ clock input with pull-high resistor. Data in the RAM of the HT1647 are clocked out on the rising edge of the RD signal. The clocked out data will appear on the data line. The host controller can use the next falling edge to latch the clocked out data. 25 WR I WRITE clock input with pull-high resistor. Data on the DATA line are latched into the HT1647 on the rising edge of the WR signal. 26~29 DB0~DB3 I/O Parallel data input/output with a pull-high resistor 30 VSS ¾ Negative power supply for logic circuit, ground 31 OSCI I 32 OSCO O The OSCI and OSCO pads are connected to a 32.768kHz crystal in order to generate a system clock. If the system clock comes from an external clock source, the external clock source should be connected to the OSCI pad. But if an on-chip RC oscillator is selected, the OSCI and OSCO pads can be left open. 33 VDD ¾ Positive power supply for logic circuit 34 VLCD I Power supply for LCD driver circuit 35 IRQ O Time base or Watchdog Timer overflow flag, NMOS open drain output. 36, 37 BZ, BZ O 2kHz or 4kHz frequency output pair (tristate output buffer) 38~41 T1~T4 I Not connected 42~57 COM0~COM15 O LCD common outputs 58~99, 1~22 SEG0~SEG63 O LCD segment outputs Absolute Maximum Ratings Supply Voltage..............................-0.3V to 5.5V Storage Temperature ................-50°C to 125°C Input Voltage................VSS-0.3V to VDD+0.3V Operating Temperature ..............-25°C to 75°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Rev. 1.00 6 June 1, 2001 HT1647 D.C. Characteristics Symbol Parameter VDD Operating Voltage IDD1 Operating Current IDD2 Operating Current IDD11 Operating Current IDD22 Operating Current ISTB Standby Current VIL Input Low Voltage VIH Input High Voltage IOL1 BZ, BZ, IRQ Sink Current IOH1 BZ, BZ Source Current IOL2 DB0~DB3 Sink Current IOH2 DB0~DB3 Source Current IOL3 LCD Common Sink Current IOH3 LCD Common Source Current IOL4 LCD Segment Sink Current IOH4 LCD Segment Source Current RPH Pull-high Resistor Rev. 1.00 Ta=25°C Test Conditions Min. Typ. Max. Unit VDD Conditions ¾ ¾ 2.7 ¾ 5.2 V 3V No load/LCD ON On-chip RC oscillator ¾ 150 250 mA ¾ 250 370 mA No load/LCD ON Crystal oscillator ¾ 135 200 mA ¾ 200 300 mA No load/LCD OFF On-chip RC oscillator ¾ 15 30 mA ¾ 50 70 mA No load/LCD OFF Crystal oscillator ¾ 2 10 mA ¾ 3 10 mA No load Power down mode ¾ ¾ 1 mA ¾ ¾ 2 mA DB0~DB3, WR, CS, RD 0 ¾ 0.6 V 0 ¾ 1.0 V DB0~DB3, WR, CS, RD 2.4 ¾ 3 V 5V 4.0 ¾ 5 V 3V VOL=0.3V 1.2 2.5 ¾ mA 5V VOL=0.5V 3 6 ¾ mA 3V VOH=2.7V -0.9 -1.8 ¾ mA 5V VOH=4.5V -2 -4 ¾ mA 5V 3V 5V 3V 5V 3V 5V 3V 5V 3V 5V 3V 3V VOL=0.3V 1.2 2.5 ¾ mA 5V VOL=0.5V 3 6 ¾ mA 3V VOH=2.7V -0.9 -1.8 ¾ mA 5V VOH=4.5V -2 -4 ¾ mA 3V VOL=0.3V 80 160 ¾ mA 5V VOL=0.5V 180 360 ¾ mA 3V VOH=2.7V -40 -80 ¾ mA 5V VOH=4.5V -90 -180 ¾ mA 3V VOL=0.3V 50 100 ¾ mA 5V VOL=0.5V 120 240 ¾ mA 3V VOH=2.7V -30 -60 ¾ mA 5V VOH=4.5V -70 -140 ¾ mA 3V DB0~DB3, WR, CS, RD 150 250 350 kW 60 125 180 kW 5V 7 June 1, 2001 HT1647 A.C. Characteristics Symbol fSYS1 Parameter System Clock fSYS2 System Clock fSYS3 System Clock fLCD1 LCD Frame Frequency fLCD2 LCD Frame Frequency fLCD3 LCD Frame Frequency tCOM LCD Common Period Ta=25°C Test Conditions VDD 3V 5V 3V 5V 3V 5V 3V 5V Conditions On-chip RC oscillator Crystal oscillator External clock source On-chip RC oscillator Max. Unit 22 32 40 kHz 24 32 40 kHz ¾ 32.768 ¾ kHz ¾ 32.768 ¾ kHz ¾ 32 ¾ kHz ¾ 32 ¾ kHz 61/117 89/170 111/213 Hz Hz 64 ¾ Hz ¾ 64 ¾ Hz ¾ 64 ¾ Hz ¾ 64 ¾ Hz ¾ n: Number of COM ¾ n/fLCD ¾ sec 3V ¾ ¾ 150 kHz ¾ ¾ 300 kHz ¾ ¾ 75 kHz ¾ ¾ 150 kHz ¾ 250 ¾ ns ¾ ¾ ms ¾ ¾ ms 5V 3V 5V Crystal oscillator External clock source 4-Bit Data Clock (WR Pin) fCLK2 4-Bit Data Clock (RD Pin) tCS 4-Bit Interface Reset Pulse ¾ CS Width (Figure 3) tCLK Typ. 61/117 89/170 111/213 3V fCLK1 WR, RD Input Pulse Width (Figure 1) Min. 5V 3V 5V 3V 5V Duty cycle 50% Duty cycle 50% ¾ Write mode 3.34 Read mode 6.67 Write mode 1.67 Read mode 3.34 tr, tf Rise/Fall Time Serial Data 3V Clock Width (Figure 1) 5V ¾ ¾ 120 ¾ ns tsu 3V Setup Time for DB to WR, RD Clock Width (Figure 2) 5V ¾ ¾ 120 ¾ ns th Hold Time for DB to WR, RD 3V Clock Width (Figure 2) 5V ¾ ¾ 120 ¾ ns tsu1 Setup Time for CS to WR, RD 3V Clock Width (Figure 3) 5V ¾ ¾ 100 ¾ ns th1 Hold Time for CS to WR, RD 3V Clock Width (Figure 3) 5V ¾ ¾ 100 ¾ ns Rev. 1.00 8 June 1, 2001 HT1647 V A L ID tf W R , R D C lo c k 9 0 % 5 0 % 1 0 % D B tr tC V tC L K ts D D G N D W R , R D C lo c k L K tC 5 0 % ts W R , R D C lo c k th u 1 1 S F IR S T C lo c k L A S T C lo c k th u 5 0 % D D G N D G N D V D D G N D V 5 0 % V Figure 2 Figure 1 C S D A T A 5 0 % D D G N D Figure 3 Functional Description System oscillator The LCD OFF command is used to turn the LCD bias generator off. After the LCD bias generator switches off by issuing the LCD OFF command, using the SYS DIS command reduces power consumption, thus serving as a system power down command. But if the external clock source is chosen as the system clock, using the SYS DIS command can neither turn the oscillator off nor carry out the power down mode. The crystal oscillator option can be applied to connect an external frequency source of 32kHz to the OSCI pin. In this case, the system fails to enter the power down mode, similar to the case in the external 32kHz clock source operation. At the initial system power on, the HT1647 is at the SYS DIS state. The HT1647 system clock is used to generate the time base/Watchdog Timer (WDT) clock frequency, LCD driving clock, and tone frequency. The clock source may be from an on-chip RC osc i l l a t or ( 3 2 k H z ) , a c r y s t a l os c i l l a t o r (32.768kHz), or an external 32kHz clock by the S/W setting. The configuration of the system oscillator is as shown. After the SYS DIS command is executed, the system clock will stop and the LCD bias generator will turn off. That command is available only for the on-chip RC oscillator or for the crystal oscillator. Once the system clock stops, the LCD display will become blank, and the time base/WDT loses its function as well. O S C I O S C O C r y s ta l O s c illa to r 3 2 7 6 8 H z E x te r n a l C lo c k S o u r c e 3 2 k H z S y s te m C lo c k O n - c h ip R C O s c illa to r 3 2 k H z System oscillator configuration Rev. 1.00 9 June 1, 2001 HT1647 the RAM are directly mapped to the contents of the LCD driver. Data in the RAM can be accessed by the READ, WRITE and READ-MODIFY-WRITE commands. The following is a mapping from the RAM to the LCD patterns. Display memory - RAM structure The static display RAM is organized into 512´4 bits and stores the display data. Two bits of RAM are mapped to an LCD¢s one pixel and then determines whether 4-level gray scale or 4-color display concurrently. The contents of C O M 1 5 C O M 1 C O M 1 4 C O M 0 S E G 0 7 0 S E G 1 1 5 8 S E G 2 2 3 1 6 S E G 3 3 1 2 4 S E G 6 3 5 1 1 5 0 4 D 3 D 2 D 1 D 0 A d d r D a ta D 3 D 2 D 1 D 0 A d d r e s s 9 B its (A 8 , A 7 , ...., A 0 ) A d d r D a ta D a ta 4 B its (D 3 , D 2 , D 1 , D 0 ) : T w o b it s o f R A M m a p t o L C D 's o n e p ix e l a n d d e c id e 4 - le v e l g r a y s c a le o r 4 - c o lo r d is p la y c o n c u r r e n tly . Display memory - RAM structure Gray scale level decision Frame frequency HT1647 uses PWM technique to provide 4-level gray scale display. Two bits of RAM data code ((D3, D2) or (D1, D0)) decide one pixel level of LCDs, level 1~level divided by 4. Every level must be defined as one kind of gray scale by PWM data (namely B4~B0) previously. HT1647 provides two kinds of frame frequency option by command code; 89Hz and 170Hz respectively. FRAME 89Hz provides 89Hz frame frequency and active segment signal width can be divided into 24 sections concurrently. FRAME 170Hz provides 170Hz frame frequency and active segment signal width can be divided into 13 sections concurrently. The 24 sections display a particularly gray scale more than the 13 sections by PWM data. The default is FRAME 89Hz. RAM data code Choice Gray Scale (D3, D2) or (D1, D0) Level (1, 1) Level 1 (1, 0) Level 2 (0, 1) Level 3 (0, 0) Level 4 Gray scale display If the user choose 89Hz frame frequency, a max. of 24 sections can be programmed to suit a satisfactory gray scale in every level. Similarly, if the user choose 170Hz frame frequency, a max. of 13 sections can be programmed to suit a RAM data defined gray scale level Rev. 1.00 10 June 1, 2001 HT1647 Name Command Code Function FRAME 170Hz X100-0001-1000-XXXX Select 170Hz frame frequency and active segment signal width can be divided into 13 sections FRAME 89Hz X100-0001-1101-XXXX Select 89Hz frame frequency and active segment signal width can be divided into 24 sections Frame frequency selection command code scale in TN-type, STN-type LCDs (refer to table 1). Similarly, it displays varied color in ECB-type LCDs. The color display is derived from ECB-type LCD specification. At FRAME 170Hz mode, the HT1647 only provides a max. of 13 adjustable gray scales although 32 is the expressed max. value by 5 bits binary code. When the 5 bits binary code value is more than 12, the PWM control circuit uniformly regards 12. The user must appoint four kinds of PWM data to four kinds of different gray scale level by commanding PWM data (refer to table 2). satisfactory gray scale in every level. HT1647 provides 5-bit PWM data to control the length of the section. In other words, a max. Of 24 gray scales are generated by 5-bit binary PWM data. At FRAME 89Hz mode, the HT1647 only provides a max. of 24 adjustable gray scales although 32 is the expressed max. value by 5 bits binary code. When 5 bits binary code value is more than 23, the PWM control circuit uniformly regards 23. To increase PWM data indicates to increase the length of the active segment signal. The varied length of the active segment signal displays varied gray Relationship table between PWM data and gray scale V a lu e 0 1 2 3 5 4 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 3 1 5 b its P W M B 4 B 3 B 2 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 1 0 0 1 0 0 0 1 0 0 1 0 0 1 0 0 1 0 1 1 0 1 1 0 1 1 0 1 1 0 0 0 1 0 0 1 0 0 1 0 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 1 0 1 1 1 d a ta B 1 B 0 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 0 0 0 1 1 0 1 1 0 0 1 1 (O N 2 2 2 1 1 1 1 1 1 1 1 1 1 P W M w id th ) G r a y S c a le 0 (0 /2 3 ) 1 /2 3 2 /2 3 3 /2 3 4 /2 3 5 /2 3 6 /2 3 7 /2 3 8 /2 3 9 /2 3 0 /2 3 1 /2 3 2 /2 3 3 /2 3 4 /2 3 5 /2 3 6 /2 3 7 /2 3 8 /2 3 9 /2 3 0 /2 3 1 /2 3 2 /2 3 1 (2 3 /2 3 ) 1 (2 4 /2 3 ) V a lu e 5 b its P W M d a ta 1 3 B 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B 3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 B 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 B 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 B 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 3 1 1 1 1 1 1 0 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 P W M (O N w id 0 (0 /1 1 /1 2 2 /1 2 3 /1 2 4 /1 2 5 /1 2 6 /1 2 7 /1 2 8 /1 2 9 /1 2 1 0 /1 2 1 1 /1 2 1 (1 2 /1 1 (1 3 /1 th ) 2 ) G r a y S c a le 2 ) 2 ) 1 (3 1 /1 2 ) Table 2: FRAME 170Hz mode Note: The varied PWM data displays various gray scale in TN-type, STN-type LCDs. The color display derives from ECB-type LCD¢s specification. 1 (3 1 /2 3 ) Table 1: FRAME 89Hz mode Rev. 1.00 11 June 1, 2001 HT1647 Name Command Code Function GRS LEVEL 1 X100-001 B4-B3 B2 B1 B0-XXXX Set PWM data in gray scale level 1 GRS LEVEL 2 X100-010 B4-B3 B2 B1 B0-XXXX Set PWM data in gray scale level 2 GRS LEVEL 3 X100-011 B4-B3 B2 B1 B0-XXXX Set PWM data in gray scale level 3 GRS LEVEL 4 X100-100 B4-B3 B2 B1 B0-XXXX Set PWM data in gray scale level 4 Four kinds of gray scale level command code 1 6 V 1 2 1 6 1 2 L C D V 1 V 2 C O M V 3 V 4 V S S W V L C D W ' V 1 V 2 S E G V 3 V V 4 S S W ' V C O M ~ S E G W L C D 3 /5 V L C D 1 /5 V L C D -1 /5 V L C D -3 /5 V L C D -V L C D O N O F F O N 1 fra m e N o t e : " W '" R e a l a c t iv e s e g m e n t s ig n a l w id t h ( a d ju s t a b le w id t h b y P W M " W " M a x . a c tiv e s e g m e n t s ig n a l w id th P W M ( O N w id t h ) : W '/ W , 0 < W '/ W < 1 ( r e f e r t o t a b le 1 & t a b e l 2 ) d a ta ) Example of waveform (B type) in 1/5 bias, 1/16 duty cycle drive Rev. 1.00 12 June 1, 2001 HT1647 The tone output can be turned off by invoking the TONE OFF command. The tone outputs, namely BZ and BZ, are a pair of differential driving outputs used to drive a piezo buzzer. Once the system is disabled or the tone output is inhibited, the BZ and the BZ outputs will remain at low level. Time base and Watchdog Timer - WDT The time base generator and WDT share the same counter which is divided by 256. The IRQ clock can be programmed as 1Hz, 2Hz, ...., 128Hz output. TIMER DIS/EN/CLR, WDT DIS/EN/CLR and IRQ EN/DIS are independent from each other. Once the WDT time-out occurs, the IRQ pin will remain at a logic low level until the CLR WDT or the IRQ DIS command is issued. Command format The HT1647 can be configured by software setting. There are two mode commands to configure the HT1647 resource and to transfer the LCD display data. If an external clock is selected as the system frequency source, the SYS DIS command turns out invalid and the power down mode fails to be carried out until the external clock source is removed. The configuration mode of the HT1647 is called command mode, and its command mode ID is 100. The command mode consists of a system configuration command, a system frequency selection command, an LCD configuration command, a tone frequency selection command, a bias current selection command, a gray scale level selection command, a timer/WDT setting command, and an operating command. The data mode, on the other hand, includes READ, WRITE, and READ-MODIFY-WRITE operations. Buzzer tone output A simple tone generator is implemented in the HT1647. The tone generator can output a pair of differential driving signals on the BZ and BZ which are used to generate a single tone. By executing the TONE 4K and TONE 2K commands there are two tone frequency outputs selectable that can turn on the tone output. The TONE 4K and TONE 2K commands set the tone frequency to 4kHz and 2kHz, respectively. T im e B a s e C lo c k S o u r c e T IM E R /2 5 6 V C L R T im e r W D T /4 IR Q E N /D IS W D T E N /D IS D D Q D C K IR Q E N /D IS R C L R W D T Time base and WDT configurations Name Command Code Function TONE OFF X100-0000-1000-XXXX Turn-off tone output TONE 4K X100-0001-0000-XXXX Turn-on tone output, tone frequency is 4kHz TONE 2K X100-0001-0001-XXXX Turn-on tone output, tone frequency is 2kHz Buzzer tone output command code Rev. 1.00 13 June 1, 2001 HT1647 The following are the data mode ID and the command mode ID: Operation Mode ID READ Data 110 WRITE Data 101 READ-MODIFY-WRITE Data 101 Command 100 COMMAND Bias generator The HT1647 bias voltage belongs to internal resistor type. It provides two kinds of bias option named 1/5 bias and 1/4 bias respectively. It is recommended to select 1/5 bias to fit TN-type, STN-type LCDs and select 1/4 bias to fit ECB-type LCDs. It also provides three kinds of bias current option by programming to suitably drive an LCD panel. The three kinds of bias current are large, middle, and small, respectively. Usually, large panel LCD can be excellently displayed by large bias current. Relatively, it consumes large current when LCD ON command is used. Small bias current provides low power consumption during On condition when the LCD is normally displayed. The following are the reference value table. If successive commands have been issued, the command mode ID can be omitted. While the system is operating in the non-successive command or the non-successive address data mode, the CS pin should be set to ²1² and the previous operation mode will also be reset. The CS pin returns to ²0², so a new operation mode ID should be issued first. VLCD Bias Large bias current Middle bias current Small bias current 4V 1/5 300mA 100mA 40mA 4V 1/4 375mA 125mA 50mA V D D V D D * V L C D * V R V L C D R V R R V 1 V 1 R V 2 R V 2 *V R *V R L C D V 3 L C D V 3 R R V 4 V 4 R R V S S V S S 1 /5 b ia s 1 /4 b ia s * T h e v o lta g e a p p lie d to V L C D p in m u s t b e lo w e r th a n V D D * A d ju s t V R to fit L C D d is p la y , a t V D D = 5 V , V L C D = 4 V , V R = 1 5 k W 2 0 % Internal resistor type bias generator configurations Rev. 1.00 14 June 1, 2001 HT1647 in the RAM are clocked out on the falling edge of the RD signal, and the clocked out data will then appear on the DB0~DB3 lines. It is recommended that the host controller read correct data during the interval between the rising edge and the next falling edge of the RD signal. The WR line is the WRITE clock input. The data, address, and command on the DB0~DB3 lines are all clocked into the HT1647 on the rising edge of the WR signal. There is an optional IRQ line to be used as an interface between the host controller and the HT1647. The IRQ pin can be selected as a timer output or a WDT overflow flag output by the S/W setting. The host controller can perform the time base or the WDT function by connecting with the IRQ pin of the HT1647. Interfacing Only six lines are required to interface with the HT1647. The CS line is used to initialize the serial interface circuit and to terminate the communication between the host controller and the HT1647. If the CS pin is set to 1, the data and command issued between the host controller and the HT1647 are first disabled and then initialized. Before issuing a mode command or mode switching, a high level pulse is required to initialize the serial interface of the HT1647. The DB0~DB3 are the 4-bit parallel data input/output lines. Data to be read or written or commands to be written have to pass through the DB0~DB3 lines. The RD line is the READ clock input. Data Timing Diagrams READ mode (command ID code : 1 1 0) C S W R R D D B 3 A 8 A 7 A 3 D 3 A 8 A 7 A 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D B 2 1 A 6 A 2 D 2 1 A 6 A 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 A 5 A 1 D 1 A 5 A 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 0 A 4 A 0 D 0 0 A 4 A 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 C o m m a n d ID A d d re s s (M A ) M e m o ry D a ta (M A ) C o m m a n d ID A d d re s s (M A ) M e m o ry D a ta (M A ) D a ta (M A + 1 ) D a ta (M A + 2 ) D a ta (M A + 3 ) D a ta (M A + 4 ) D a ta (M A + 5 ) D a ta (M A + 6 ) D a ta (M A + 7 ) D a ta (M A + 8 ) D a ta (M A + 9 ) D a ta (M A + 1 0 ) D a ta (M A + 1 1 ) D a ta (M A + 1 2 ) D a ta (M A + 1 3 ) D a ta (M A + 1 4 ) D a ta (M A + 1 5 ) 1 D B 1 D B 0 1 c o d e c o d e ( S in g le a d d r e s s r e a d in g ) Rev. 1.00 ( S u c c e s s iv e a d d r e s s r e a d in g ) 15 June 1, 2001 HT1647 WRITE mode (command ID code : 1 0 1) C S W R R D A 7 A 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D B 2 1 A 6 A 2 D 2 1 A 6 A 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 A 5 A 1 D 1 A 5 A 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 A 4 A 0 D 0 1 A 4 A 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 A d d re s s (M A ) M e m o ry D a ta (M A ) C o m m a n d ID A d d re s s (M A ) M e m o ry D a ta (M A ) D a ta (M A + 1 ) D a ta (M A + 2 ) D a ta (M A + 3 ) D a ta (M A + 4 ) D a ta (M A + 5 ) 0 D B 1 1 D B 0 0 D a ta (M A + 1 2 ) D a ta (M A + 1 3 ) D a ta (M A + 1 4 ) D a ta (M A + 1 5 ) A 8 A 7 A 3 D 3 D 3 A 8 A 7 A 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D 3 D B 2 1 A 6 A 2 D 2 D 2 1 A 6 A 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D 2 D B 1 0 A 5 A 1 D 1 D 1 A 5 A 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D 1 D B 0 1 A 4 A 0 D 0 D 0 1 A 4 A 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 D 0 A d d re s s (M A ) M e m o ry D a ta (M A ) D a ta (M A ) C o m m a n d ID M e m o ry D a ta (M A ) D a ta (M A ) D a ta (M A + 1 ) D a ta (M A + 1 ) D a ta (M A + 2 ) D a ta (M A + 2 ) D a ta (M A + 3 ) D a ta (M A + 3 ) D a ta (M A + 4 ) D a ta (M A + 4 ) D a ta (M A + 5 ) D a ta (M A + 5 ) D a ta (M A + 6 ) D a ta (M A + 6 ) c o d e c o d e D B 3 C o m m a n d ID C o m m a n d ID D a ta (M A + 1 1 ) A 8 D a ta (M A + 1 0 ) D 3 D a ta (M A + 9 ) A 3 D a ta (M A + 8 ) A 7 D a ta (M A + 7 ) A 8 D a ta (M A + 6 ) D B 3 ( S in g le a d d r e s s w r itin g ) ( S u c c e s s iv e a d d r e s s w r itin g ) READ-MODIFY-WRITE mode (command ID code : 1 0 1) C S W R R D 0 A d d re s s (M A ) c o d e c o d e ( S in g le a d d r e s s a c c e s s in g ) Rev. 1.00 ( S u c c e s s iv e a d d r e s s a c c e s s in g ) 16 June 1, 2001 HT1647 Command mode (command ID code : 1 0 0) C S W R R D D B 3 X C 8 1 D B 2 0 D B 1 D B 0 0 C 4 C 0 C 7 C 3 X C 6 C 2 C 5 C 1 X 1 0 X X 0 C 8 C 4 C 0 C 8 C 4 C 7 C 3 X C 7 C 3 C 6 C 2 X C 6 C 2 C 5 C 1 X C 5 C 1 C 0 C 8 C 4 C 0 X C 7 C 3 X X C 6 C 2 X C 5 C 1 C 8 C 4 C 7 C 3 X C 6 C 2 X C 5 C 1 C 0 X C 8 C 4 C 7 C 3 X C 6 C 2 X C 5 C 1 C 0 X C 8 C 4 C 0 C 7 C 3 X C 6 C 2 X X C 5 C 1 X X C o m m a n d 6 C o m m a n d 5 C o m m a n d 4 C o m m a n d 3 C o m m a n d 2 C o m m a n d 1 C o m m a n d ID C o m m a n d C o m m a n d ID c o d e c o d e ( S in g le c o m m a n d ) ( S u c c e s s iv e c o m m a n d ) Note: ²X² stands for don¢t care Rev. 1.00 17 June 1, 2001 HT1647 Application Circuits Host controller with an HT1647 display system C S * V D D R D *V R W R D B 0 ~ D B 3 m C *R V L C D H T 1 6 4 7 B Z P ie z o IR Q B Z O S C I C lo c k O u t O S C O C O M 0 ~ C O M 1 5 S E G 0 ~ S E G 6 3 E x te r n a l C lo c k 1 ( 3 2 k H z ) E x te r n a l C lo c k 2 ( 3 2 k H z ) * 1 /5 B ia s ( o r 1 /4 B ia s ) , 1 /1 6 D u ty O n - c h ip O S C L C D P a n e l C ry s ta l 3 2 7 6 8 H z *Note: The connection of IRQ and RD pin can be selected depending on the mC. The voltage applied to VLCD pin must be lower than VDD. Adjust VR to fit LCD display, at VDD=5V, VLCD=4V, VR=15kW ± 20%. It is recommended to select 1/5 bias to fit TN-type, STN-type LCDs and select 1/4 bias to fit ECB-type LCDs. Adjust R (external pull high resistance) to fit user¢s time base clock. Rev. 1.00 18 June 1, 2001 HT1647 Instruction Set Summary Name Command Code D/C Function Def. READ A8110-A7A6A5A4A3A2A1A0D3D2D1D0 D Read data from the RAM WRITE A8101-A7A6A5A4A3A2A1A0D3D2D1D0 D Write data to the RAM READMODIFYWRITE A8101-A7A6A5A4A3A2A1A0D3D2D1D0 D Read and Write data to the RAM SYS DIS X100-0000-0000-XXXX C Turn Off both system oscillator and LCD bias generator SYS EN X100-0000-0001-XXXX C Turn On system oscillator LCD OFF X100-0000-0010-XXXX C Turn Off LCD display LCD ON X100-0000-0011-XXXX C Turn On LCD display TIMER DIS X100-0000-0100-XXXX C Disable time base output WDT DIS X100-0000-0101-XXXX C Disable WDT time-out flag output Yes TIMER EN X100-0000-0110-XXXX C Enable time base output WDT EN X100-0000-0111-XXXX C Enable WDT time-out flag output TONE OFF X100-0000-1000-XXXX C Turn Off tone outputs CLR TIMER X100-0000-1101-XXXX C Clear the contents of the time base generator CLR WDT X100-0000-1111-XXXX C Clear the contents of the WDT stage TONE 4K X100-0001-0000-XXXX C Turn on tone output, tone frequency output: 4kHz TONE 2K X100-0001-0001-XXXX C Turn on tone output, tone frequency output: 2kHz IRQ DIS X100-0001-0010-XXXX C Disable IRQ output IRQ EN X100-0001-0011-XXXX C Enable IRQ output RC 32K X100-0001-0100-XXXX C System clock source, on-chip RC oscillator EXT (XTAL) X100-0001-0101-XXXX C System clock source, external 32kHz clock source or crystal oscillator 32.768kHz LARGE BIAS X100-0001-0110-XXXX C Large bias current option MIDDLE BIAS X100-0001-0111-XXXX C Middle bias current option Rev. 1.00 19 Yes Yes Yes Yes Yes Yes Yes June 1, 2001 HT1647 Name Command Code D/C Function Def. SMALL BIAS X100-0001-1000-XXXX C Small bias current option BIAS 1/5 X100-0001-1001-XXXX C LCD 1/5 bias option BIAS 1/4 X100-0001-1010-XXXX C LCD 1/4 bias option FRAME 170Hz X100-0001-1100-XXXX C Selects 170Hz frame frequency and active segment signal width can be divided into 13 sections FRAME 89Hz X100-0001-1101-XXXX C Selects 89Hz frame frequency and active segment signal width can be divided into 24 sections GRS LEVEL1 X100-001 B4-B3 B2 B1 B0-XXXX C Sets PWM data in gray scale level 1 GRS LEVEL2 X100-010 B4-B3 B2 B1 B0-XXXX C Sets PWM data in gray scale level 2 GRS LEVEL3 X100-011 B4-B3 B2 B1 B0-XXXX C Sets PWM data in gray scale level 3 GRS LEVEL4 X100-100 B4-B3 B2 B1 B0-XXXX C Sets PWM data in gray scale level 4 F1 X100-1010-0000-XXXX C Time base clock output: 1Hz The WDT time-out flag after: 4s F2 X100-1010-0001-XXXX C Time base clock output: 2Hz The WDT time-out flag after: 2s F4 X100-1010-0010-XXXX C Time base clock output: 4Hz The WDT time-out flag after: 1s F8 X100-1010-0011-XXXX C Time base clock output: 8Hz The WDT time-out flag after: s F16 X100-1010-0100-XXXX C Time base clock output: 16Hz The WDT time-out flag after: 1/4 s F32 X100-1010-0101-XXXX C Time base clock output: 32Hz The WDT time-out flag after: 1/8 s F64 X100-1010-0110-XXXX C Time base clock output: 64Hz The WDT time-out flag after: 1/16 s F128 X100-1010-0111-XXXX C Time base clock output: 128Hz Yes The WDT time-out flag after: 1/32 s TEST X100-1111-1111-XXXX C Test mode, user don¢t use. NORMAL X100-1111-1110-XXXX C Normal mode Rev. 1.00 20 Yes Yes Yes June 1, 2001 HT1647 Note: ²X² stands for don¢t care A8~A0 : RAM address D3~D0 : RAM data B4~B0 : PWM data D/C : Data/Command mode Def. : Power-on reset default All the bold forms, namely 1 1 0, 1 0 1, and 1 0 0, are mode commands. Of these, 1 0 0 indicates the command mode ID. If successive commands have been issued, the command mode ID except for the first command will be omitted. The tone frequency source and the time base/WDT clock frequency source can be derived from an on-chip 32kHz RC oscillator, a 32.768kHz crystal oscillator, or an external 32kHz clock. Calculation of the frequency is based on the system frequency sources as stated above. It is recommended that the host controller should initialize the HT1647 after power-on reset, otherwise, power on reset may fail, which in turn leads to the malfunctioning of the HT1647. Rev. 1.00 21 June 1, 2001 HT1647 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Tel: 886-3-563-1999 Fax: 886-3-563-1189 Holtek Semiconductor Inc. (Taipei Office) 11F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan, R.O.C. Tel: 886-2-2782-9635 Fax: 886-2-2782-9636 Fax: 886-2-2782-7128 (International sales hotline) Holtek Semiconductor (Hong Kong) Ltd. RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong Tel: 852-2-745-8288 Fax: 852-2-742-8657 Holtek Semiconductor (Shanghai) Ltd. 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China Tel: 021-6485-5560 Fax: 021-6485-0313 Holmate Technology Corp. 48531 Warm Springs Boulevard, Suite 413, Fremont, CA 94539 Tel: 510-252-9880 Fax: 510-252-9885 Copyright ã 2001 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.00 22 June 1, 2001