ETC TPS5210DWR

TPS5210
PROGRAMMABLE SYNCHRONOUS-BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
D
D
D
D
D
D
D
D
D
D
D
D
±1% Reference Over Full Operating
Temperature Range
Synchronous Rectifier Driver for Greater
Than 90% Efficiency
Programmable Reference Voltage Range of
1.3 V to 3.5 V
User–Selectable Hysteretic Type Control
Droop Compensation for Improved Load
Transient Regulation
Adjustable Overcurrent Protection
Programmable Softstart
Overvoltage Protection
Active Deadtime Control
Power Good Output
Internal Bootstrap Schottky Diode
Low Supply Current . . . 3-mA Typ
DW OR PWP PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
IOUT
DROOP
OCP
VHYST
VREFB
VSENSE
ANAGND
SLOWST
BIAS
LODRV
LOHIB
DRVGND
LOWDR
DRV
28
27
26
25
24
23
22
21
20
19
18
17
16
15
PWRGD
VID0
VID1
VID2
VID3
VID4
INHIBIT
IOUTLO
LOSENSE
HISENSE
BOOTLO
HIGHDR
BOOT
VCC
description
The TPS5210 is a synchronous-buck regulator controller which provides an accurate, programmable supply
voltage to microprocessors. An internal 5-bit DAC is used to program the reference voltage to within a range
of 1.3 V to 3.5 V. The output voltage can be set to be equal to the reference voltage or to some multiple of the
reference voltage. A hysteretic controller with user-selectable hysteresis and programmable droop
compensation is used to dramatically reduce overshoot and undershoot caused by load transients. Propagation
delay from the comparator inputs to the output drivers is less than 250 ns. Overcurrent shutdown and crossover
protection for the output drivers combine to eliminate destructive faults in the output FETs. The softstart current
source is proportional to the reference voltage, thereby eliminating variation of the softstart timing when
changes are made to the output voltage. PWRGD monitors the output voltage and pulls the open-collector
output low when the output drops 7% below the nominal output voltage. An overvoltage circuit disables the
output drivers if the output voltage rises 15% above the nominal value. The inhibit pin can be used to control
power sequencing. Inhibit and undervoltage lockout assures the 12-V supply voltage and system supply voltage
(5 V or 3.3 V) are within proper operating limits before the controller starts. Single-supply (12 V) operation is
easily accomplished using a low-current divider for the required 5-V signals. The output driver circuits include
2-A drivers with internal 8-V gate-voltage regulators. The high-side driver can be configured either as a
ground-referenced driver or as a floating bootstrap driver. The TPS5210 is available in a 28-pin SOIC package
and a 28-pin TSSOP PowerPAD package. It operates over a junction temperature range of 0°C to 125°C.
AVAILABLE OPTIONS
PACKAGES
TJ
SOIC
(DW)
0°C to 125°C
TPS5210DW
TSSOP
(PWP)
TPS5210PWPR
The DW package is available taped and reeled. Add R suffix to device
type (e.g., TPS5210DWR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
1
INHIBIT
15
7
28
LOSENSE
20
21
19
NOCPU
2V
22
+
–
UVLO
Shutdown
S
VCC
Rising
Edge
Delay
Deglitch
HIGHDR
Deglitch
VPGD
0.93 Vref
VOVP
1.15 Vref
HIGHIN
VCC
VSENSE
8
PREREG
Analog Bias
+
–
Bandgap
Analog
Bias
9
IVREFB
5
–
+
Slowstart
Comp
14
DRV REG
Shutdown
16
CM Filters
VID
MUX
and
Decoder
17
+
VREF
Σ
+
–
–
+ –
27
26
IOUT
2x
Fault
R
25
24
23
Hysteresis
Comp
Shutdown
200 kΩ
Hysteresis
Setting
I VREFB
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
1
Q
+
100 mV
SLOWST
IOUTLO HISENSE
11111
Decode
10 V
OCP
PWRGD
2
4
13
6
VID0 VID1 VID2 VID3 VID4 VREFB DROOP VHYST VSENSE
11
10
LOHIB
LODRV
DRV
BOOT
HIGHDR
200 kΩ
18
BOOTLO
12
5
BIAS
LOWDR
DRVGND
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
VID0
VID1
VID2
VID3
VID4
ANAGND
functional block diagram
2
VCC
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
ANAGND
7
BIAS
9
O
Analog ground
Analog BIAS pin. A 1-µF ceramic capacitor should be connected from BIAS to ANAGND.
BOOT
16
I
Bootstrap. Connect a 1-µF low-ESR capacitor from BOOT to BOOTLO.
BOOTLO
18
O
Bootstrap low. Connect BOOTLO to the junction of the high-side and low-side FETs for floating drive
configuration. Connect BOOTLO to PGND for ground reference drive configuration.
DROOP
2
I
Droop voltage. Voltage input used to set the amount of output-voltage set-point droop as a function of load
current. The amount of droop compensation is set with a resistor divider between IOUT and ANAGND.
DRV
14
O
Drive regulator for the FET drivers. A 1-µF ceramic capacitor should be connected from DRV to DRVGND.
DRVGND
12
HIGHDR
17
O
High drive. Output drive to high-side power switching FETs
HISENSE
19
I
High current sense. For current sensing across high-side FETs, connect to the drain of the high-side FETs; for
optional resistor sensing scheme, connect to power supply side of current-sense resistor placed in series with
high-side FET drain.
INHIBIT
22
I
Disables the drive signals to the MOSFET drivers. Can also serve as UVLO for system logic supply (either 3.3 V
or 5 V).
IOUT
1
O
Current out. Output voltage on this pin is proportional to the load current as measured across the Rds(on) of the
high-side FETs. The voltage on this pin equals 2×Rds(on)×IOUT. In applications where very accurate current
sensing is required, a sense resistor should be connected between the input supply and the drain of the high-side
FETs.
IOUTLO
21
O
Current sense low output. This is the voltage on the LOSENSE pin when the high-side FETs are on. A ceramic
capacitor should be connected from IOUTLO to HISENSE to hold the sensed voltage while the high-side FETs
are off. Capacitance range should be between 0.033 µF and 0.1 µF.
LODRV
10
I
Low drive enable. Normally tied to 5 V. To activate the low-side FETs as a crowbar, pull LODRV low.
LOHIB
11
I
Low side inhibit. Connect to the junction of the high and low side FETs to control the anti-cross-conduction and
eliminate shoot-through current. Disabled when configured in crowbar mode.
LOSENSE
20
I
Low current sense. For current sensing across high-side FETs, connect to the source of the high-side FETs; for
optional resistor sensing scheme, connect to high-side FET drain side of current-sense resistor placed in series
with high-side FET drain.
LOWDR
13
O
Low drive. Output drive to synchronous rectifier FETs
OCP
3
I
Over current protection. Current limit trip point is set with a resistor divider between IOUT and ANAGND.
PWRGD
28
O
Power good. Power Good signal goes high when output voltage is within 7% of voltage set by VID pins.
Open-drain output.
SLOWST
8
O
Slow Start (soft start). A capacitor from SLOWST to ANAGND sets the slowstart time.
Slowstart current = IVREFB/5
VCC
15
VHYST
4
I
HYSTERESIS set pin. The hysteresis is set with a resistor divider from VREFB to ANAGND.
The hysteresis window = 2 × (VREFB – VHYST)
VID0
27
I
Voltage Identification input 0
VID1
26
I
Voltage Identification input 1
VID2
25
I
Voltage Identification input 2
VID3
24
I
Voltage Identification input 3
VID4
23
I
Voltage Identification input 4. Digital inputs that set the output voltage of the converter. The code pattern for
setting the output voltage is located in Table 1. Internally pulled up to 5 V with a resistor divider biased from VCC.
VREFB
5
O
Buffered reference voltage from VID network
VSENSE
6
I
Voltage sense Input. To be connected to converter output voltage bus to sense and control output voltage. It is
recommended an RC low pass filter be connected at this pin to filter noise.
Drive ground. Ground for FET drivers. Connect to FET PWRGND.
12-V supply. A 1-µF ceramic capacitor should be connected from VCC to DRVGND.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
3
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
detailed description
VREF
The reference/voltage identification (VID) section consists of a temperature-compensated bandgap reference
and a 5-bit voltage selection network. The 5 VID terminals are inputs to the VID selection network and are
TTL-compatible inputs internally pulled up to 5 V by a resistor divider connected to VCC. The VID codes conform
to the Intel VRM 8.3 DC-DC Converter Specification for voltage settings between 1.8 V and 3.5 V, and they are
decremented by 50 mV, down to 1.3 V, for the lower VID settings. Voltages higher than VREF can be implemented
using an external divider. Refer to Table 1 for the VID code settings. The output voltage of the VID network, VREF,
is within ±1% of the nominal setting over the VID range of 1.3 V to 2.5 V, including a junction temperature range
of 5°C to +125°C, and a VCC supply voltage range of 11.4 V to 12.6 V. The output of the reference/VID network
is indirectly brought out through a buffer to the VREFB pin. The voltage on this pin will be within 2% of VREF. It
is not recommended to drive loads with VREFB, other than setting the hysteresis of the hysteretic comparator,
because the current drawn from VREFB sets the charging current for the slowstart capacitor. Refer to the
slowstart section for additional information.
hysteretic comparator
The hysteretic comparator regulates the output voltage of the synchronous-buck converter. The hysteresis is
set by 2 external resistors and is centered on VREF. The 2 external resistors form a resistor divider from VREFB
to ANAGND, with the output voltage connecting to the VHYST pin. The hysteresis of the comparator will be equal
to twice the voltage difference between the VREFB and VHYST pins. The propagation delay from the comparator
inputs to the driver outputs is 250 ns (maximum). The maximum hysteresis setting is 60 mV.
low-side driver
The low-side driver is designed to drive low-Rds(on) n-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The bias to the low-side driver is internally connected to the DRV regulator.
high-side driver
The high-side driver is designed to drive low-Rds(on) n-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The high-side driver can be configured either as a ground-referenced driver or as a floating
bootstrap driver. When configured as a floating driver, the bias voltage to the driver is developed from the DRV
regulator. The internal bootstrap diode, connected between the DRV and BOOT pins, is a Schottky for improved
drive efficiency. The maximum voltage that can be applied between BOOT and DRVGND is 30 V. The driver
can be referenced to ground by connecting BOOTLO to DRVGND, and connecting BOOT to either DRV or VCC.
deadtime control
Deadtime control prevents shoot-through current from flowing through the main power FETs during switching
transitions by actively controlling the turn-on times of the MOSFET drivers. The high-side driver is not allowed
to turn on until the gate-drive voltage to the low-side FETs is below 2 V; the low-side driver is not allowed to turn
on until the voltage at the junction of the high-side and low-side FETs (Vphase) is below 2 V.
current sensing
Current sensing is achieved by sampling and holding the voltage across the high-side power FETs while the
high-side FETs are on. The sampling network consists of an internal 60-Ω switch and an external ceramic hold
capacitor. Recommended value of the hold capacitor is between 0.033 µF and 0.1 µF. Internal logic controls
the turn-on and turn-off of the sample/hold switch such that the switch does not turn on until the Vphase voltage
transitions high, and the switch turns off when the input to the high-side driver goes low. The sampling will occur
only when the high-side FETs are conducting current. The voltage on the IOUT pin equals 2 times the sensed
high-side voltage. In applications where a higher accuracy in current sensing is required, a sense resistor can
be placed in series with the high-side FETs, and the voltage across the sense resistor can be sampled by the
current sensing circuit.
4
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
detailed description (continued)
droop compensation
The droop compensation network reduces the load transient overshoot/undershoot on VO, relative to VREF . VO
is programmed to a voltage greater than VREF by an external resistor divider from VO to VSENSE to reduce the
undershoot on VO during a low-to-high load transient. The overshoot during a high-to-low load transient is
reduced by subtracting the voltage on DROOP from VREF. The voltage on IOUT is divided with an external
resistor divider, and connected to DROOP.
inhibit
INHIBIT is a TTL-compatible digital input used to enable the controller. When INHIBIT is low, the output drivers
are low and the slowstart capacitor is discharged. When INHIBIT goes high, the short across the slowstart
capacitor is released and normal converter operation begins. When the system-logic supply is connected to
INHIBIT, it also controls power sequencing by locking out controller operation until the system-logic supply
exceeds the input threshold voltage of the inhibit circuit. The 12-V supply and the system logic supply (either
5 V or 3.3 V) must be above UVLO thresholds before the controller is allowed to start up. The start threshold
is 2.1 V and the hysteresis is 100 mV for the INHIBIT comparator.
VCC undervoltage lockout (UVLO)
The undervoltage lockout circuit disables the controller while the VCC supply is below the 10-V start threshold
during power up. When the controller is disabled, the output drivers will be low and the slowstart capacitor is
discharged. When VCC exceeds the start threshold, the short across the slowstart capacitor is released and
normal converter operation begins. There is a 2-V hysteresis in the undervoltage lockout circuit for noise
immunity.
slowstart
The slowstart circuit controls the rate at which VO powers up. A capacitor is connected between SLOWST and
ANAGND and is charged by an internal current source. The current source is proportional to the reference
voltage, so that the charging rate of Cslowst is proportional to the reference voltage. By making the charging
current proportional to VREF, the power-up time for VO will be independent of VREF. Thus, CSLOWST can remain
the same value for all VID settings. The slowstart charging current is determined by the following equation:
Islowstart = I(VREFB) / 5 (amps)
Where I(VREFB) is the current flowing out of VREFB.
It is recommended that no additional loads be connected to VREFB, other than the resistor divider for setting the
hysteresis voltage. The maximum current that can be sourced by the VREFB circuit is 500 µA. The equation for
setting the slowstart time is:
tSLOWST = 5 × CSLOWST × RVREFB
(seconds)
Where RVREFB is the total external resistance from VREFB to ANAGND.
power good
The power-good circuit monitors for an undervoltage condition on VO. If VO is 7% below VREF, then the PWRGD
pin is pulled low. PWRGD is an open-drain output.
overvoltage protection
The overvoltage protection (OVP) circuit monitors VO for an overvoltage condition. If VO is 15% above VREF,
then a fault latch is set and both output drivers are turned off. The latch will remain set until VCC goes below the
undervoltage lockout value. A 3-µs deglitch timer is included for noise immunity. Refer to the LODRV section
for information on how to protect the microprocessor against overvoltages due to a shorted fault across the
high-side power FET.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
5
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
detailed description (continued)
overcurrent protection
The overcurrent protection (OCP) circuit monitors the current through the high-side FET. The overcurrent
threshold is adjustable with an external resistor divider between IOUT and ANAGND, with the divider voltage
connected to the OCP pin. If the voltage on OCP exceeds 100 mV, then a fault latch is set and the output drivers
are turned off. The latch will remain set until VCC goes below the undervoltage lockout value. A 3-µs deglitch
timer is included for noise immunity. The OCP circuit is also designed to protect the high-side power FET against
a short-to-ground fault on the terminal common to both power FETs.
drive regulator
The drive regulator provides drive voltage to the output drivers. The minimum drive voltage is 7 V. The minimum
short circuit current is 100 mA. Connect a 1-µF ceramic capacitor from DRV to DRVGND.
LODRV
The LODRV circuit is designed to protect the microprocessor against overvoltages that can occur if the high-side
power FETs become shorted. External components to sense an overvoltage condition are required to use this
feature. When an overvoltage fault occurs, the low-side FETs are used as a crowbar. LODRV is pulled low and
the low-side FET will be turned on, overriding all control signals inside the TPS5210 controller. The crowbar
action will short the input supply to ground through the faulted high-side FETs and the low-side FETs. A fuse
in series with Vin should be added to disconnect the short-circuit.
Table 1. Voltage Identification Codes
VID TERMINALS
(0 = GND, 1 = floating or pull-up to 5 V)
VREF
VID4
VID3
VID2
VID1
VID0
(Vdc)
0
1
1
1
1
1.30
0
1
1
1
0
1.35
0
1
1
0
1
1.40
0
1
1
0
0
1.45
0
1
0
1
1
1.50
0
1
0
1
0
1.55
0
1
0
0
1
1.60
0
1
0
0
0
1.65
0
0
1
1
1
1.70
0
0
1
1
0
1.75
0
0
1
0
1
1.80
0
0
1
0
0
1.85
0
0
0
1
1
1.90
0
0
0
1
0
1.95
0
0
0
0
1
2.00
0
0
0
0
0
2.05
1
1
1
1
1
No CPU
1
1
1
1
0
2.10
1
1
1
0
1
2.20
1
1
1
0
0
2.30
1
1
0
1
1
2.40
1
1
0
1
0
2.50
1
1
0
0
1
2.60
6
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
Table 1. Voltage Identification Codes (Continued)
VID TERMINALS
(0 = GND, 1 = floating or pull-up to 5 V)
VREF
VID4
VID3
VID2
VID1
VID0
(Vdc)
1
1
0
0
0
2.70
1
0
1
1
1
2.80
1
0
1
1
0
2.90
1
0
1
0
1
3.00
1
0
1
0
0
3.10
1
0
0
1
1
3.20
1
0
0
1
0
3.30
1
0
0
0
1
3.40
1
0
0
0
0
3.50
absolute maximum ratings over operating virtual junction temperature (unless otherwise noted)†
Supply voltage range, VCC (see Note1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 14 V
Input voltage range: BOOT to DRVGND (High-side Driver ON) . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 30 V
BOOT to HIGHDRV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 15 V
BOOT to BOOTLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 15 V
INHIBIT, VIDx, LODRV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 7.3 V
PWRGD, OCP, DROOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 7 V
LOHIB, LOSENSE, IOUTLO, HISENSE . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 14 V
VSENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 5 V
Voltage difference between ANAGND and DRVGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.5 V
Output current, VREFB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 mA
Short circuit duration, DRV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: Unless otherwise specified, all voltages are with respect to ANAGND.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
DW
1200 mW
12 mW/°C
660 mW
480 mW
PWP
1150 mW
11.5 mW/°C
630 mW
460 mW
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
7
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
recommended operating conditions
MIN
MAX
11.4
13
V
Input voltage, BOOT to DRVGND
0
28
V
Input voltage, BOOT to BOOTLO
0
13
V
Input voltage, INHIBIT, VIDx, LODRV, PWRGD, OCP, DROOP
0
6
V
Input voltage, LOHIB, LOSENSE, IOUTLO, HISENSE
0
13
V
Input voltage, VSENSE
0
4.5
V
Voltage difference between ANAGND and DRVGND
Output current, VREFB†
0
±0.2
V
0
0.4
mA
Supply voltage, VCC
UNIT
† Not recommended to load VREFB other than to set hystersis since IVREFB sets slowstart time.
electrical characteristics over recommended operating virtual junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted)
reference/voltage identification
PARAMETER
TEST CONDITIONS
VCC = 11.4 to 12.6 V, 1.3 V ≤ VREF ≤ 2.5 V
VCC = 11.4 to 12.6 V, VREF = 2.6 V
Reference voltage accuracy, (Includes
offset of droop compensation network)
VREF
Cumulative reference accuracy
(see Note 2)
VIDx
High-level input voltage
VIDx
Low-level input voltage
VREFB
VIDx
MIN
TYP
MAX
UNIT
–0.01
0.01
V/V
–0.0104
0.0104
V/V
VCC = 11.4 to 12.6 V, VREF = 2.7 V
VCC = 11.4 to 12.6 V, VREF = 2.8 V
VCC = 11.4 to 12.6 V, VREF = 2.9 V
–0.0108
0.0108
V/V
–0.0112
0.0112
V/V
–0.0116
0.0116
V/V
VCC = 11.4 to 12.6 V, VREF = 3 V
VCC = 11.4 to 12.6 V, VREF = 3.1 V
VCC = 11.4 to 12.6 V, VREF = 3.2 V
–0.0120
0.0120
V/V
–0.0124
0.0124
V/V
–0.0128
0.0128
V/V
VCC = 11.4 to 12.6 V, VREF = 3.3 V
VCC = 11.4 to 12.6 V, VREF = 3.4 V
VCC = 11.4 to 12.6 V, VREF = 3.5 V
–0.0132
0.0132
V/V
–0.0136
0.0136
V/V
–0.0140
0.0140
V/V
–0.011
0.011
–0.008
0.008
VREF = 1.9 Vv, Hysteresis,
TJ = 60°C window = 30 mV (see Note 3)
–0.0090
0.0090
VREF = 3.5 V, Hysteresis,
TJ = 60°C window = 30 mV (see Note 3)
–0.0115
0.0115
VREF = 1.3 V, Hysteresis window = 30 mV
VREF =1.3 V, Hysteresis,
TJ = 60°C window = 30 mV (see Note 3)
2.25
V
1
Output voltage
IVREFB = 50 µA
Output regulation
10 µA ≤ IO ≤ 500 µA
Input resistance
VIDx = 0 V
VREF–2%
Input pull-up voltage divider
V/V
VREF VREF+2%
2
V
V
mV
36
73
95
kΩ
4.8
4.9
5
V
NOTES: 2. Cumulative reference accuracy is the combined accuracy of the reference voltage and the input offset voltage of the hysteretic
comparator. Cumulative accuracy equals the average of the high-level and low-level thresholds of the hysteretic comparator.
3. This parameter is ensured by design and is not production tested.
8
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
electrical characteristics over recommended operating virtual junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted) (continued)
power good
PARAMETER
TEST CONDITIONS
Undervoltage trip threshold
VOL
IOH
Low-level output voltage
Vhys
Hysteresis voltage
MIN
90
IO = 5 mA
VPWRGD = 6 V
High-level input current
TYP
93
0.5
MAX
UNIT
95 %VREF
V
0.75
µA
1
1.3
2.9
4.5 %VREF
MIN
TYP
MAX
UNIT
10.4
13
15.6
µA
slowstart
PARAMETER
TEST CONDITIONS
Charge current
VSLOWST = 0.5 V,
IVREFB = 65 µA
Discharge current
VSLOWST = 1 V
VVREFB = 1.3 V,
3
Comparator input offset voltage
Comparator input bias current
mA
10
See Note 3
10
Comparator hysteresis
–7.5
mV
100
nA
7.5
mV
NOTE 3: This parameter is ensured by design and is not production tested.
hysteretic comparator
PARAMETER
Input offset voltage
Input bias current
Hysteresis accuracy
TEST CONDITIONS
–2.5
VREFB – VHYST = 15 mV
(Hysteresis window = 30 mV)
–3.5
Maximum hysteresis setting
VREFB – VHYST = 30 mV
NOTE 3: This parameter is ensured by design and is not production tested.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
MIN
VDROOP = 0 V (see Note 3)
See Note 3
• DALLAS, TEXAS 75265
TYP
MAX
2.5
60
UNIT
mV
500
nA
3.5
mV
mV
9
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
electrical characteristics over recommended operating virtual junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted) (continued)
high-side VDS sensing
PARAMETER
TEST CONDITIONS
MIN
Gain
Initial accuracy
Sink current
5 V ≤ VIOUTLO ≤ 13 V
IOUT
Source current
VIOUT = 0.5 V,
VIOUTLO = 11.5 V
IOUT
Sink current
VIOUT = 0.05 V, VHISENSE = 12 V,
VIOUTLO = 12 V
Output voltage swing
VHISENSE = 11 V, RIOUT = 10 kΩ
VHISENSE = 4.5 V, RIOUT = 10 kΩ
VHISENSE = 3 V, RIOUT = 10 kΩ
LOSENSE
MAX
2
VHISENSE = 12 V,
VLOSENSE = 11.9 V,
Differential input to Vds sensing amp = 100 mV
IOUTLO
TYP
High-level input voltage
Low-level input voltage
Sample/hold resistance
VHISENSE = 12 V,
4 5 V (see Note 3)
VHISENSE = 4.5
11.4 V ≤ VHISENSE ≤ 12.6 V,
LOSENSE connected to HISENSE,
VHISENSE – VIOUTLO = 0.15 V
4.5 V ≤ VHISENSE ≤ 5.5 V,
LOSENSE connected to HISENSE,
VHISENSE – VIOUTLO = 0.15 V
3 V ≤ VHISENSE ≤ 3.6 V,
LOSENSE connected to HISENSE,
VHISENSE – VIOUTLO = 0.15 V
VHISENSE = 12.6 V to 3 V,
CMRR
VHISENSE – VOUTLO = 100 mV
NOTE 3. This parameter is ensured by design and is not production tested.
194
UNIT
V/V
206
mV
250
nA
500
µA
50
µA
0
2
V
0
1.5
V
0
0.75
V
2.85
V
2.4
V
50
60
80
62
85
123
67
95
144
69
75
MIN
TYP
MAX
UNIT
Ω
dB
inhibit
PARAMETER
TEST CONDITIONS
Start threshold
1.9
2.1
2.35
V
Hysteresis
0.08
0.1
0.12
V
Stop threshold
1.85
V
overvoltage protection
PARAMETER
TEST CONDITIONS
Overvoltage trip threshold
Hysteresis
MIN
TYP
112
115
See Note 3
10
MAX
UNIT
120 %VREF
mV
NOTE 3: This parameter is ensured by design and is not production tested.
overcurrent protection
PARAMETER
TEST CONDITIONS
OCP trip threshold
Input bias current
10
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
MIN
TYP
MAX
90
100
110
UNIT
mV
100
nA
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
electrical characteristics over recommended operating virtual junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted) (continued)
deadtime
PARAMETER
LOHIB
LOWDR
TEST CONDITIONS
High-level input voltage
MIN
TYP
MAX
2.4
Low-level input voltage
1.4
High-level input voltage
See Note 3
Low-level input voltage
See Note 3
3
1.7
UNIT
V
V
NOTE 3: This parameter is ensured by design and is not production tested.
LODRV
PARAMETER
LODRV
TEST CONDITIONS
High-level input voltage
MIN
TYP
MAX
1.85
Low-level input voltage
0.95
UNIT
V
droop compensation
PARAMETER
TEST CONDITIONS
Initial accuracy
VDROOP = 50 mV
MIN
TYP
46
MAX
54
UNIT
mV
drive regulator
PARAMETER
TEST CONDITIONS
Output voltage
11.4 V ≤ VCC ≤ 12.6 V,
Output regulation
1 mA ≤ IDRV ≤ 50 mA
IDRV = 50 mA
MIN
TYP
7
MAX
9
100
Short-circuit current
UNIT
V
mV
100
mA
bias regulator
PARAMETER
Output voltage
TEST CONDITIONS
11.4 V ≤ VCC ≤ 12.6 V,
See Note 4
MIN
TYP
MAX
6
UNIT
V
NOTE 4: The bias regulator is designed to provide a quiet bias supply for the TPS5210 controller. External loads should not be driven by the bias
regulator.
input undervoltage lockout
PARAMETER
TEST CONDITIONS
Start threshold
MIN
TYP
MAX
UNIT
9.25
10
10.75
V
Hysteresis
1.9
2
2.2
V
Stop threshold
7.5
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
V
11
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
electrical characteristics over recommended operating virtual junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted) (continued)
output drivers
PARAMETER
Peak output
current
(see Note 5)
tpw < 100 µs,
VBOOT – VBOOTLO = 6.5 V,
High-side sink
Duty cycle < 2%,
TJ = 125°C,
High-side source
VHIGHDR = 1.5 V (source) or 6 V (sink),
See Note 3
Low-side sink
Duty Cycle < 2%,
TJ = 125°C,
Low-side source
VLOWDR = 1.5 V (source) or 5 V (sink),
See Note 3
High-side sink
Output
resistance
(see Note 5)
TEST CONDITIONS
High-side source
Low-side sink
Low-side source
tpw < 100 µs,
VDRV = 6.5 V,
MIN
TYP
MAX
UNIT
2
2
A
2
2
3
TJ = 125°C,,
VBOOT – VBOOTLO = 6.5 V,,
VHIGHDR = 6 V (source) or 0.5 V (sink)
45
5.7
TJ = 125°C,
VDRV = 6.5 V,
VLOWDR = 6 V (source) or 0.5 V (sink)
Ω
45
NOTES: 3. This parameter is ensured by design and is not production tested.
5. The pull-up/pull-down circuits of the drivers are bipolar and MOSFET transistors in parallel. The peak output current rating is the
combined current from the bipolar and MOSFET transistors. The output resistance is the Rds(on) of the MOSFET transistor when
the voltage on the driver output is less than the saturation voltage of the bipolar transistor.
supply current
PARAMETER
VCC
TEST CONDITIONS
Supply voltage
range
VINHIBIT = 5 V,
VCC > 10.75 V at startup,
VCC
Quiescent
current
High-side
driver
quiescent
current
VID code ≠ 11111,
VBOOTLO = 0 V
VINHIBIT = 5 V,
VID code ≠ 11111,
VCC > 10.75 V at startup,
VBOOTLO = 0 V,
CHIGHDR = 50 pF,
CLOWDR = 50 pF,
fSWX = 200 kHz,
See Note 3
VINHIBIT = 0 V or VID code = 11111 or VCC < 9.25 V at startup,
VBOOT = 13 V,
VBOOTLO = 0 V
VINHIBIT = 5 V,
VID code ≠ 11111, VCC > 10.75 V at startup,
VBOOT = 13 V,
VBOOTLO = 0 V,
CHIGHDR = 50 pF,
fSWX = 200 kHz (see Note 3)
NOTE 3: This parameter is ensured by design and is not production tested.
12
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
MIN
TYP
MAX
11.4
12
13
3
10
UNIT
V
mA
5
80
2
µA
mA
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
switching characteristics over recommended operating virtual-junction temperature range,
VCC = 12 V, IDRV = 0 A (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VSENSE to HIGHDR or
LOWDR (excluding deadtime)
Propagation
Pro
agation delay
MIN
1.3 V ≤ VVREF ≤ 3.5 V, 10 mV overdrive
(see Note 3)
OCP comparator
UNIT
150
250
ns
1
SLOWST comparator
Overdrive = 10 mV (see Note 3)
HIGHDR output
CL = 9 nF,
VBOOTLO = 0 V,
VBOOT = 6.5 V,
TJ = 125°C
LOWDR output
CL = 9 nF,
TJ = 125°C
VDRV = 6.5 V,
HIGHDR output
CL = 9 nF,
VBOOTLO = 0 V,
VBOOT = 6.5 V,
TJ = 125°C
LOWDR output
CL = 9 nF,
TJ = 125°C
VDRV = 6.5 V,
Rise time
Fall time
µs
1
PWRGD comparator
Response time
MAX
1
See Note 3
OVP comparator
Deglitch time (Includes
comparator propagation
delay)
TYP
OCP
560
900
60
ns
60
60
ns
60
2
5
2
5
See Note 3
OVP
High-side VDS sensing
VHISENSE = 12 V,
VIOUTLO pulsed from 12 V to 11.9 V,
100 ns rise/fall times
(see Note 3)
2
VHISENSE = 4.5 V,
VIOUTLO pulsed from 4.5 V to 4.4 V,
100 ns rise/fall times (see Note 3)
3
VHISENSE = 3 V,
VIOUTLO pulsed from 3 V to 2.9 V,
100 ns rise/fall times (see Note 3)
3
Short-circuit protection
rising-edge delay
SCP
LOSENSE = 0 V (see Note 3)
Turn-on/turn-off delay
VDS sensing sample/hold
switch
Crossover delay time
ns
µs
µs
300
500
ns
3 V ≤ VHISENSE ≤ 11 V,
VLOSENSE = VHISENSE (see Note 3)
30
100
ns
LOWDR to HIGHDRV, and
LOHIB to LOWDR
See Note 3
30
100
ns
Prefilter pole frequency
Hysteretic comparator
See Note 3
Propagation delay
LODRV
See Note 3
5
MHz
400
ns
NOTE 3: This parameter is ensured by design and is not production tested.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
13
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
TYPICAL CHARACTERISTICS
SLOWSTART TIME
vs
SLOWSTART CAPACITANCE
SLOWSTART TIME
vs
SUPPLY CURRENT (VREFB)
100
1000
V(VREFB) = 2 V
I(VREFB) = 100 µA
TJ = 25°C
V(VREFB) = 2 V
CS = 0.1 µF
TJ = 25°C
Slowstart Time – ms
Slowstart Time – ms
10
1
100
10
0.1
0
0.0001
0.0010
0.0100
0.1000
1
1
1
10
Slowstart Capacitance – µF
Figure 1
DRIVER
DRIVER
OUTPUT RISE TIME
vs
LOAD CAPACITANCE
OUTPUT FALL TIME
vs
LOAD CAPACITANCE
1000
TJ = 25°C
TJ = 25°C
t f – Fall Time – ns
t r – Rise Time – ns
1000
Figure 2
100
High Side
Low Side
10
1
0.1
100
ICC – Supply Current (VREFB) – µA
1
10
100
100
High Side
1
0.1
CL – Load Capacitance – nF
1
10
CL – Load Capacitance – nF
Figure 3
14
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Low Side
10
Figure 4
• DALLAS, TEXAS 75265
100
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
TYPICAL CHARACTERISTICS
OVP THRESHOLD
vs
JUNCTION TEMPERATURE
OCP THRESHOLD VOLTAGE
vs
JUNCTION TEMPERATURE
118
105
OCP Threshold Voltage – mV
OVP Threshold – %
117
116
115
114
113
112
0
25
50
75
100
103
101
99
97
95
125
0
25
TJ – Junction Temperature – °C
Figure 5
75
100
125
Figure 6
INHIBIT START THRESHOLD VOLTAGE
vs
JUNCTION TEMPERATURE
INHIBIT HYSTERESIS VOLTAGE
vs
JUNCTION TEMPERATURE
2.1
150
Inhibit Hysteresis Voltage – mV
Inhibit Start Threshold Voltage – V
50
TJ – Junction Temperature – °C
2.05
2
1.95
1.9
0
25
50
75
100
125
125
100
75
50
0
TJ – Junction Temperature – °C
50
75
100
125
TJ – Junction Temperature – °C
Figure 7
Figure 8
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
25
• DALLAS, TEXAS 75265
15
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
TYPICAL CHARACTERISTICS
UVLO START THRESHOLD VOLTAGE
vs
JUNCTION TEMPERATURE
UVLO HYSTERESIS
vs
JUNCTION TEMPERATURE
10.5
2.5
VI = 12 V
2.3
UVLO Hysteresis – V
UVLO Start Threshold Voltage – V
VI = 12 V
10
9.5
2.1
1.9
1.7
9
0
25
50
75
100
1.5
125
0
TJ – Junction Temperature – °C
25
50
75
100
125
TJ – Junction Temperature – °C
Figure 9
Figure 10
QUIESCENT CURRENT
vs
JUNCTION TEMPERATURE
POWERGOOD THRESHOLD
vs
JUNCTION TEMPERATURE
6
95
VI = 12 V
Powergood Threshold – %
Quiescent Current – mA
94
4
2
93
92
91
0
0
25
50
75
100
125
90
0
TJ – Junction Temperature – °C
50
75
100
TJ – Junction Temperature – °C
Figure 11
16
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
25
Figure 12
• DALLAS, TEXAS 75265
125
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
TYPICAL CHARACTERISTICS
DRIVER
SLOW START CHARGE CURRENT
vs
JUNCTION TEMPERATURE
REGULATOR VOLTAGE
vs
JUNCTION TEMPERATURE
15
8.5
14
8.25
Regulator Voltage – V
Slow Start Charge Current – µ A
V(VREFB) = 1.3 V
R(VREFB) = 20 kΩ
13
12
8
7.75
11
10
0
25
50
75
100
7.5
125
0
TJ – Junction Temperature – °C
25
Figure 13
75
100
125
Figure 14
DRIVER
DRIVER
HIGH-SIDE OUTPUT RESISTANCE
vs
JUNCTION TEMPERATURE
LOW-SIDE OUTPUT RESISTANCE
vs
JUNCTION TEMPERATURE
5
6
RO – Low-Side Output Resistance – Ω
RO – High-Side Output Resistance – Ω
50
TJ – Junction Temperature – °C
4
3
2
1
0
4
2
0
0
25
50
75
100
125
0
TJ – Junction Temperature – °C
50
75
100
125
TJ – Junction Temperature – °C
Figure 15
Figure 16
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
25
• DALLAS, TEXAS 75265
17
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
TYPICAL CHARACTERISTICS
SENSING SAMPLE/HOLD RESISTANCE
vs
JUNCTION TEMPERATURE
100
RO – Sensing Sample/Hold Resistance – Ω
V(HISENSE) = 12 V
75
50
25
0
0
25
50
75
100
TJ – Junction Temperature – °C
Figure 17
18
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
125
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
The following figure is a typical application schematic. The circuit can be divided into the power-stage section
and the control-circuit section. The power stage must be tailored to the input/output requirements of the
application. The control circuit is basically the same for all applications with some minor tweaking of specific
values. Table 2 shows the values of the power stage components for various output-current options.
L101
L102
Q101
12V
Vo
R102
Q102
+
C101
+
C102
C105
C104
C103
R101
C106
GND
RTN
C2
1 uF
RTN
VSENSE
LODRV
LOHIB
DRVGND
BOOTLO
LOSENSE
HISENSE
12V
Control Section
HIGHDRV
Power Stage
C1
1 uF
C3
1 uF
15
16
17
18
R1
3.40 k
1%
19
C6
0.033 uF
20
21
22
ENABLE
23
24
R4
2.55 k
1%
C8
2200 pF
25
26
27
28
VCC
DRV
BOOT
LOWDR
HIGHDR
DRVGND
BOOTLO
LOHIB
HISENSE
LODRV
LOSENSE
BIAS
IOUTLO
SLOWST
INHIBIT
ANAGND
VID4
VSENSE
VID3
VREFB
VID2
VHYST
VID1
OCP
VID0
DROOP
PWRGD
IOUT
14
R2
150
13
12
C4
1 uF
11
C5
0.1 uF
C7
10
9
8
7
6
1000 pF
R5
100
5
4
3
R3 10.0 k
R7
3.92 k
R6
20.0 k
R8
1.00 k
R9
4.32 k
R10
1.00 k
2
1
TPS5210
U1
Figure 18. Standard Application Schematic
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
19
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
Table 2. Power Stage Components
Ref
Des
12-V–Input Power Stage Components
F nction
Function
4–A Out
8–A Out
12–A Out
20–A Out
40–A Out
C101
Input Bulk
Capacitor
Sanyo,
16SV100M,
100–uF, 16–V, 20%
Sanyo,
16SA470M,
2 x 470–uF, 16–V, 20%
Sanyo,
16SA470M,
2 x 470–uF, 16–V, 20%
Sanyo,
16SA470M,
3 x 470–uF, 16–V, 20%
Sanyo,
16SA470M,
4 x 470–uF, 16–V, 20%
C102
Input
Mid–Freq
Capacitor
muRata,
GRM42–6Y5V105Z025A
1.0–uF, 25–V,
+80%–20%,
Y5V
muRata,
GRM42–6Y5V225Z016A
2.2–uF, 16–V,
+80%–20%,
Y5V
muRata,
GRM42–6Y5V225Z016A
2.2–uF, 16–V,
+80%–20%,
Y5V
muRata,
GRM42–6Y5V105Z025A
3 x 1.0–uF, 25–V,
+80%–20%,
Y5V
muRata,
GRM42–6Y5V105Z025A
4 x 1.0–uF, 25–V,
+80%–20%,
Y5V
C103
Input
Hi–Freq
Bypass
Capacitor
muRata,
GRM39X7R104K016A
0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
2 x 0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
3 x 0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
4 x 0.1–uF, 16–V, X7R
C104
Snubber
Capacitor
muRata,
GRM39X7R102K050A,
1000–pF, 50–V, X7R
muRata,
GRM39X7R102K050A,
1000–pF, 50–V, X7R
muRata,
GRM39X7R102K050A,
2 x 1000–pF, 50–V, X7R
muRata,
GRM39X7R102K050A,
3 x 1000–pF, 50–V, X7R
muRata,
GRM39X7R102K050A,
4 x 1000–pF, 50–V, X7R
C105
Output Bulk
Capacitor
Sanyo,
6TPB150M,
3 x 150–uF, 6.3–V, 20%
Sanyo,
4SP820M,
820–uF, 4–V, 20%
Sanyo,
4SP820M,
2 x 820–uF, 4–V, 20%
Sanyo,
4SP820M,
3 x 820–uF, 4–V, 20%
Sanyo,
4SP820M,
4 x 820–uF, 4–V, 20%
C106
Output
Hi–Freq
Bypass
Capacitor
muRata,
GRM39X7R104K016A,
0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
2 x 0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
3 x 0.1–uF, 16–V, X7R
muRata,
GRM39X7R104K016A,
4 x 0.1–uF, 16–V, X7R
L101
Input
Filter
Inductor
CoilCraft,
DO1608C–332,
3.3–uH, 2.0–A
Coiltronics,
UP2B–2R2,
2.2–uH, 7.2–A
Coiltronics,
UP2B–2R2,
2.2–uH, 7.2–A
Coiltronics,
UP3B–1R0,
1–uH, 12.5–A
Coiltronics,
UP3B–1R0,
1–uH, 12.5–A
L102
Output
Filter
Inductor
CoilCraft,
DO3316P–332,
3.3–uH, 6.1–A
Coiltronics,
UP3B–2R2,
2.2–uH, 9.2–A
Coiltronics,
UP4B–1R5,
1.5–uH, 13.4–A
MicroMetals,
T68–8/90 Core w/7T
#16, 1.0–uH, 25–A
Pulse Engineering,
P1605,
1.0–uH, 50–A
R101
Lo–Side
Gate
Resistor
3.3–Ohm,
1/16–W, 5%
3.3–Ohm,
1/16–W, 5%
2 x 3.3–Ohm,
1/16–W, 5%
3 x 3.3–Ohm,
1/16–W, 5%
4 x 3.3–Ohm,
1/16–W, 5%
R102
Snubber
Resistor
2.7–Ohm,
1/10–W, 5%
2.7–Ohm,
1/10–W, 5%
2 x 2.7–Ohm,
1/10–W, 5%
3 x 2.7–Ohm,
1/10–W, 5%
4 x 2.7–Ohm,
1/10–W, 5%
Q101
Power
Switch
Siliconix, Si4410,
NMOS, 13–mOhm
Siliconix, Si4410,
NMOS, 13–mOhm
Siliconix, 2 x Si4410,
NMOS, 13–mOhm
Siliconix, 2 x Si4410,
NMOS, 13–mOhm
IR, 2 x IRF7811,
NMOS, 11–mOhm
Q102
Synchronous
Switch
Siliconix, Si4410,
NMOS, 13–mOhm
Siliconix, Si4410,
NMOS, 13–mOhm
Siliconix, 2 x Si4410,
NMOS, 13–mOhm
Siliconix, 3 x Si4410,
NMOS, 13–mOhm
IR, 4 x IRF7811,
NMOS, 11–mOhm
Nominal Frequency†
220 KHz
330 KHz
240 KHz
140 KHz
168 KHz
Hysteresis Window
20 mV
20 mV
20 mV
20 mV
10 mV
† Nominal frequency measured with Vo set to 2 V.
The values listed above are recommendations based on actual test circuits. Many variations of the above are
possible based upon the desires and/or requirements of the user. Performance of the circuit is equally, if not
more, dependent upon the layout than on the specific components, as long as the device parameters are not
exceeded. Fast-response, low-noise circuits require critical attention to the layout details. Even though the
operating frequencies of typical power supplies are relatively low compared to today’s microprocessor circuits,
the power levels and edge rates can cause severe problems both in the supply and the load. The power stage,
having the highest current levels and greatest dv/dt rates, should be given the greatest attention.
20
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
frequency calculation
A detailed derivation of frequency calculation is shown in the application report, “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044. When less accurate results
are acceptable, the simplified equation shown below can be used:
fs ≅
ǒ
ǒ ƪ* ƫ Ǔ
VO
VI
L
VI
VO
ESR
Hysteresis Window
Ǔ
Control Section
Below are the equations needed to select the various components within the control section. Details and the
derivations of the equations used in this section are available in the application report “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044.
output voltage selection
Of course the most important function of the power supply is to regulate the output voltage to a specific value.
Values between 1.3 V and 3.5 V can be easily set by shorting the correct VID inputs to ground. Values above
the maximum reference voltage (3.5 V) can be set by setting the reference voltage to any convenient voltage
within its range and selecting values for R2 and R3 to give the correct output. Select R3:
R3 << than VREF/IBIAS(VSENSE); a recommended value is 10 kΩ
ǒ Ǔ
Then, calculate R2 using:
VO
+ VREF 1 ) R2
R3
or
R2
+
R3
ǒ
VO
Ǔ
* VREF
V REF
R2 and R3 can also be used to make small adjusts to the output voltage within the reference-voltage range
and/or to adjust for load-current active droop compensation. If there is no need to adjust the output voltage, R3
can be eliminated. R2, R3 (if used), and C7 are used as a noise filter; calculate using:
C7
+ ǒR2150ø nsR3Ǔ
slowstart timing
Slowstart reduces the startup stresses on the power-stage components and reduces the input current surge.
Slowstart timing is a function of the reference-voltage current (determined by R6) and is independent of the
reference voltage. The first step in setting slowstart timing will be to determine R6:
R6 should be between 7 kΩ and 300 kΩ, a recommended value is 20 kΩ.
Set the slowstart timing using the formula:
C5
+ ǒ5
t SS
R VREFB
Ǔ
≅
t SS
(5
R6)
Where C5 = Slowstart capacitance in µF
tSS = Slowstart timing in µs
RVREFB = Resistance from VREFB to GND in ohms (≈ R6)
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
21
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
hysteresis voltage
A hysteretic controller regulates by self-oscillation, thus requiring a small ripple voltage on the output which the
input comparator uses for sensing. Once selected, the TPS5210 hysteresis is proportional to the reference
voltage; programming Vref to a new value automatically adjusts the hysteresis to be the same percentage of
Vref. The actual output ripple voltage is the combination of the hysteresis voltage, overshoot caused by internal
delays, and the output capacitor characteristics. Figure 20 shows the hysteresis window voltage (VHI to VLO)
and the output voltage ripple (VMAX to VMIN). Since the output current from VREFB should be less than 500 µA,
the total divider resistance (R5 + R6) should be greater than 7 KΩ. The hysteresis voltage should be no greater
than 60 mV so R6 will dominate the divider.
VREFB
Hysteresis Window = 2 × VR5
R5
VHSYT
R6
Figure 19. Hysteresis Divider Circuit
VO
VMAX
VHI
VREF
VLO
VMIN
t
Figure 20. Output Ripple
The upper divider resistor, R5, is calculated using:
R5 =
Hysteresis Window
V HYST (0 0 )
× R6 ≅
× R6
(2 × VREFB – Hysteresis Window )
(2 × 100 )
Where Hysteresis Window = the desired peak-to-peak hysteresis voltage.
VREFB = selected reference voltage.
VHYST (%) = [(Hysteresis Window)/VREFB] * 100 < VO(Ripple)(P–P) (%)
22
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
current limit
Current limit can be implemented using the on-resistance of the upper FETs as the sensing elements. Select
R8:
R 8 <<
0.1V
V OCP
≤
≤ 10 k Ω
(100 × 100 nA )
I Bias (OCP )
(A recommended value is 1 kΩ)
The IOUT signal is used to drive the current limit and droop-circuit dividers. The voltage at IOUT at the output
current trip point will be:
V IOUT (Trip ) =
(2 × R DS(ON ) × TF )
NumFETs
× I O(Trip )
Where NumFETS = Number of upper FETS in Parallel.
TF = RDS(ON) temperature correction factor.
IO(Trip) = Desired output current trip level (A).
ǒ
Calculate R7 using:
R7
+
V IOUT(Trip)
0.1 V
Ǔ
*1
R8
Note that since RDS(ON) of MOSFETs can vary from lot to lot and with temperature, tight current-limit control (less
than 1.5 x IO) using this method is not practical. If tight control is required, an external current-sense resistor
in series with the drain of the upper FET can be used with HISENSE and LOSENSE connected across the
resistor.
droop compensation
Droop compensation is used to reduce the output voltage range during load transients by increasing the output
voltage setpoint toward the upper tolerance limit during light loads and decreasing the voltage setpoint toward
the lower tolerance limit during heavy loads. This allows the output voltage to swing a greater amount and still
remain within the tolerance window. The maximum droop voltage is set with R9 and R10. Select R10:
R10 <<
V DROOP ( Min )
I Bias ( DROOP ,Max )
≤
0.01V
(100 × 100 nA)
≤ 1 kΩ
(Again, a value of 1 kΩ is recommended)
The voltage at IOUT during normal operation (0 to 100% load) will vary from 0 V up to:
V IOUT ( Max ) =
(2 × R DS(ON ) × TF )
NumFETs
× I O( Max )
Where IO(Max) = Maximum output load current (A).
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
23
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
ǒ
droop compensation (continued)
Then, calculate R9:
R9
+
V IOUT(Max)
V DROOP
*1
Ǔ
R10
Where VDROOP = Desired droop voltage
ǒ ) Ǔ*
At full load, the output voltage will be:
VO
+ VREF
R2
R3
1
V DROOP
using the TPS5210 when both 12 V and 5 V are available
When both 12 V and 5 V are available, several components can be removed from the basic schematic shown
above. R1, R4, and C9 are no longer required if 5 V is brought in directly to INHIBIT and LODRV. However, if
undervoltage lockout for the 5-V input is desired, R1 and R4 can be used to set the startup setpoint. The INHIBIT
pin trip level is 2.1 V. Select R4:
R 4 <<
V INH
I INH ( Max )
2.1V
≤
(100 × 100 nA )
≤ 210 k Ω
Then, set the 5-V UVLO trip level with R1:
R1 =
(5V Trip
– 2V
2V
)
× R4
LODRV
R1
INHIBIT
R4
Figure 21. 5-V Input with UVLO
using the TPS5210 when only 5 V is available
The TPS5210 controller requires 12 V for internal control of the device. If an external source for 12 V is not
available, a small on-board source must be included in the design. Total 12-V current is very small, typically
about 20 mA, so even a small charge pump can be used to generate the supply voltage. The power stage is
not voltage dependent, but component values must be selected for 5-V inputs and the frequency of operation
is dependent upon the power stage input voltage.
24
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
L101
L102
Q101
5V
Vo
R102
Q102
+
C101
+
C102
C105
C103
C106
C104
R101
GND
RTN
RTN
VSENSE
LODRV
C2
LOHIB
DRVGND
BOOTLO
HISENSE
LOSENSE
5V
HIGHDRV
Power Stage
Control Section
1 uF
C1
0.1 uF
12 V
12-V
Boost
Circuit
C3
1 uF
15
16
17
18
19
R1
10.0 k
1%
C6
0.033 uF
ENABLE
20
21
22
23
24
R4
11.0 k
1%
C8
2200 pF
25
26
27
28
VCC
DRV
BOOT
LOWDR
HIGHDR
DRVGND
BOOTLO
LOHIB
HISENSE
LODRV
LOSENSE
BIAS
IOUTLO
SLOWST
INHIBIT
ANAGND
VID4
VSENSE
VID3
VREFB
VID2
VHYST
VID1
OCP
VID0
DROOP
PWRGD
IOUT
14
R2
150
13
12
C4
1 uF
11
C5
0.1 uF
C7
10
9
8
7
6
1000 pF
R5
100
5
4
3
R3 10.0 k
R7
3.92 k
R6
20.0 k
R8
1.00 k
R9
4.32 k
R10
1.00 k
2
1
TPS5210
U1
Figure 22. Typical 5-V-Only Application Circuit
application examples
Various application and layout examples using the TPS5210 are available from Texas Instruments. This
information can be downloaded from http://www.ti.com/sc/docs/products/msp/pwrsply/default.htm or received
from your TI representative.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
25
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
APPLICATION INFORMATION
layout guidelines
Good power supply results will only occur when care is given to proper design and layout. Layout will affect noise
pickup and generation and can cause a good design to perform with less than expected results. With a range
of currents from milliamps to tens or even hundreds of amps, good power supply layout is much more difficult
than most general PCB design. The general design should proceed from the switching node to the output, then
back to the driver section, and, finally, place the low-level components. Below are several specific points to
consider before layout of a TPS5210 design begins.
1. All sensitive analog components should be referenced to ANAGND. These include components connected
to SLOWST, DROOP, IOUT, OCP, VSENSE, VREFB, VHYST, BIAS, and LOHIB.
2. Analog ground and drive ground should be isolated as much as possible. Ideally, analog ground will connect
to the ground side of the bulk storage capacitors on VO, and drive ground will connect to the main ground
plane close to the source of the low-side FET.
3. Connections from the drivers to the gate of the power FETs, should be as short and wide as possible to
reduce stray inductance. This becomes more critical if external gate resistors are not being used.
4. The bypass capacitor for the DRV regulator should be placed close to the TPS5210 and be connected to
DRVGND.
5. The bypass capacitor for VCC should be placed close to the TPS5210 and be connected to DRVGND.
6. When configuring the high-side driver as a floating driver, the connection from BOOTLO to the power FETs
should be as short and as wide as possible. The other pins that also connect to the power FETs, LOHIB
and LOSENSE, should have a separate connection to the FETS since BOOTLO will have large peak
currents flowing through it.
7. When configuring the high-side driver as a floating driver, the bootstrap capacitor (connected from BOOT
to BOOTLO) should be placed close to the TPS5210.
8. When configuring the high-side driver as a ground-referenced driver, BOOTLO should be connected to
DRVGND.
9. The bulk storage capacitors across VI should be placed close to the power FETS. High-frequency bypass
capacitors should be placed in parallel with the bulk capacitors and connected close to the drain of the
high-side FET and to the source of the low-side FET.
10. High-frequency bypass capacitors should be placed across the bulk storage capacitors on VO.
11. HISENSE and LOSENSE should be connected very close to the drain and source, respectively, of the
high-side FET. HISENSE and LOSENSE should be routed very close to each other to minimize
differential-mode noise coupling to these traces. Ceramic decoupling capacitors should be placed close to
where HISENSE connects to Vin, to reduce high-frequency noise coupling on HISENSE.
26
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
MECHANICAL DATA
DW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
16 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
16
0.010 (0,25) M
9
0.419 (10,65)
0.400 (10,15)
0.010 (0,25) NOM
0.299 (7,59)
0.293 (7,45)
Gage Plane
0.010 (0,25)
1
8
0°– 8°
A
0.050 (1,27)
0.016 (0,40)
Seating Plane
0.104 (2,65) MAX
0.012 (0,30)
0.004 (0,10)
PINS **
0.004 (0,10)
16
20
24
28
A MAX
0.410
(10,41)
0.510
(12,95)
0.610
(15,49)
0.710
(18,03)
A MIN
0.400
(10,16)
0.500
(12,70)
0.600
(15,24)
0.700
(17,78)
DIM
4040000 / C 07/96
NOTES: A.
B.
C.
D.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
Falls within JEDEC MS-013
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
27
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
MECHANICAL DATA
PWP (R-PDSO-G**)
PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
20-PIN SHOWN
0,30
0,19
0,65
20
0,10 M
11
Thermal Pad
(See Note D)
4,50
4,30
0,15 NOM
6,60
6,20
Gage Plane
1
10
0,25
A
0°– 8°
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
14
16
20
24
28
A MAX
5,10
5,10
6,60
7,90
9,80
A MIN
4,90
4,90
6,40
7,70
9,60
DIM
4073225/E 03/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusions.
The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane. This pad is electrically
and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-153
PowerPAD is a trademark of Texas Instruments Incorporated.
28
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Powered by ICminer.com Electronic-Library Service CopyRight 2003