ETC TPS76633DR

TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
D
D
D
D
D
D
D
D
D PACKAGE
(TOP VIEW)
250-mA Low-Dropout Voltage Regulator
Available in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V,
3.0-V, 3.3-V, 5.0-V Fixed Output and
Adjustable Versions
Dropout Voltage to 140 mV (Typ) at 250 mA
(TPS76650)
Ultra-Low 35-µA Typical Quiescent Current
3% Tolerance Over Specified Conditions for
Fixed-Output Versions
Open Drain Power Good
8-Pin SOIC Package
Thermal Shutdown Protection
NC/FB
PG
GND
EN
1
8
2
7
3
6
4
5
OUT
OUT
IN
IN
description
This device is designed to have an ultra-low quiescent current and be stable with a 4.7-µF capacitor. This
combination provides high performance at a reasonable cost.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 230 mV
at an output current of 250 mA for the TPS76650) and is directly proportional to the output current. Additionally,
since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent
of output loading (typically 35 µA over the full range of output current, 0 mA to 250 mA). These two key
specifications yield a significant improvement in operating life for battery-powered systems. This LDO family
also features a sleep mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the
quiescent current to less than 1 µA (typ).
TPS76633
TPS76633
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
GROUND CURRENT
vs
LOAD CURRENT
100
35.0
VI = 3.2 V
I GND – Ground Current – µ A
V DO – Output Voltage – V
IO = 250 mA
IO = 150 mA
10–1
IO = 50 mA
IO = 10 mA
10–2
34.9
VO = 3.3 V
34.8
TA = 25°C
34.7
34.6
34.5
34.4
34.3
34.2
34.1
10–3
34
–50
–25
0
25
50
75
100
125
150
0
25
TA – Free-Air Temperature – °C
50
75 100 125 150 175 200 225 250
IL – Load Current – mA
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
1
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
description (continued)
Power good (PG) is an active high output, which can be used to implement a power-on reset or a low-battery
indicator.
The TPS766xx is offered in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V and 5.0-V fixed-voltage versions and
in an adjustable version (programmable over the range of 1.25 V to 5.5 V). Output voltage tolerance is specified
as a maximum of 3% over line, load, and temperature ranges. The TPS766xx family is available in 8 pin SOIC
package.
AVAILABLE OPTIONS
TJ
OUTPUT VOLTAGE
(V)
PACKAGED DEVICES
TYP
SOIC
(D)
5.0
TPS76650D
3.3
TPS76633D
3.0
TPS76630D
2.8
TPS76628D
2.7
TPS76627D
2.5
TPS76625D
1.8
TPS76618D
1.5
TPS76615D
Adjustable
1.25 V to 5.5 V
TPS76601D
– 40°C
40 C to 125
125°C
C
The TPS76601 is programmable using an external resistor divider (see application
information). The D package is available taped and reeled. Add an R suffix to the
device type (e.g., TPS76601DR).
TPS766xx
VI
5
IN
PG
6
NC/FB
IN
OUT
0.1 µF
4
EN
OUT
2
PG
1
7
VO
8
+
GND
3
CO †
4.7 µF
300 mΩ
† See application information section for capacitor selection details.
Figure 1. Typical Application Configuration for Fixed Output Options
2
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
functional block diagram—adjustable version
IN
EN
PG
_
+
OUT
+
_
R1
Vref = 1.224 V
FB/NC
R2
GND
External to the device
functional block diagram—fixed-voltage version
IN
EN
PG
_
+
OUT
+
_
R1
Vref = 1.224 V
R2
GND
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
3
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
Terminal Functions – SOIC Package
TERMINAL
NAME
NO.
I/O
DESCRIPTION
EN
4
I
Enable input
FB/NC
1
I
Feedback input voltage for adjustable device (no connect for fixed options)
GND
3
IN
5
IN
OUT
Regulator ground
I
Input voltage
6
I
Input voltage
7
O
Regulated output voltage
OUT
8
O
Regulated output voltage
PG
2
O
PG output
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)Ĕ
Input voltage range‡, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 16.5 V
Maximum PG voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See dissipation rating tables
Output voltage, VO (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ All voltage values are with respect to network terminal ground.
DISSIPATION RATING TABLE 1 – FREE-AIR TEMPERATURES
PACKAGE
D
AIR FLOW
(CFM)
TA < 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
0
568 mW
5.68 mW/°C
312 mW
227 mW
250
904 mW
9.04 mW/°C
497 mW
361 mW
recommended operating conditions
MIN
MAX
Input voltage, VIk
2.7
10
Output voltage range, VO
1.2
5.5
V
0
250
mA
– 40
125
°C
Output current, IO (Note 1)
Operating virtual junction temperature, TJ (Note 1)
UNIT
V
k To calculate the minimum input voltage for your maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load).
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
4
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
electrical characteristics over recommended operating free-air temperature
Vi = VO(typ) + 1 V, IO = 10 µA, EN = 0 V, CO = 4.7 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TPS76601
Output voltage
(10 µA to 250 mA load)
(see Note 2)
5.5 V ≥ VO ≥ 1.25 V,
5.5 V ≥ VO ≥ 1.25 V,
TJ = 25°C
TJ = –40°C to 125°C
TPS76615
TJ = 25°C,
TJ = –40°C to 125°C,
2.7 V < VIN < 10 V
TPS76618
TJ = 25°C,
TJ = –40°C to 125°C,
2.8 V < VIN < 10 V
TPS76625
TJ = 25°C,
TJ = –40°C to 125°C,
3.5 V < VIN < 10 V
TPS76627
TJ = 25°C,
TJ = –40°C to 125°C,
3.7 V < VIN < 10 V
TPS76628
TJ = 25°C,
TJ = –40°C to 125°C,
3.8 V < VIN < 10 V
TPS76630
TJ = 25°C,
TJ = –40°C to 125°C,
4.0 V < VIN < 10 V
TPS76633
TJ = 25°C,
TJ = –40°C to 125°C,
4.3 V < VIN < 10 V
TPS76650
TJ = 25°C,
TJ = –40°C to 125°C,
6.0 V < VIN < 10 V
2.7 V < VIN < 10 V
2.8 V < VIN < 10 V
3.5 V < VIN < 10 V
3.7 V < VIN < 10 V
3.8 V < VIN < 10 V
4.0 V < VIN < 10 V
4.3 V < VIN < 10 V
6.0 V < VIN < 10 V
MIN
TYP
0.97VO
1.03VO
1.455
1.545
1.8
1.746
1.854
2.5
2.425
2.575
2.7
2.619
2.781
2.884
3.0
2.910
3.090
3.3
3.201
3.399
5.0
4.850
5.150
VO + 1 V < VI ≤ 10 V, TJ = 25°C
0.01
Load regulation
IO = 10 µA to 250 mA
BW = 300 Hz to 50 kHz,
CO = 4.7 µF,
TJ = 25°C
0.5%
35
50
VO = 0 V
0.8
Standby current
FB input current
TPS76601
EN = VI,
TJ = –40°C to 125°C
2.7 V < VI < 10 V
PG
1
µA
2
Minimum input voltage for valid PG
Trip threshold voltage
VO decreasing
Hysteresis voltage
Measured at VO
Output low voltage
VI = 2.7 V,
Leakage current
V(PG) = 5 V
V
63
V
98
0.5
0.15
EN = 0 V
–1
EN = VI
–1
0
V
dB
1.1
92
IO(PG) = 1mA
µA
nA
0.8
CO = 4.7 µF,
TJ = 25°C
A
°C
2.0
f = 1 kHz,
IO = 10 µA,
IO(PG) = 300µA
Input current (EN)
1.2
150
Low level enable input voltage
Power supply ripple rejection (see Note 2)
µVrms
10
FB = 1.5 V
High level enable input voltage
µA
%/V
200
Thermal shutdown junction temperature
TJ = 25°C,
2.7 V < VI < 10 V
V
2.8
2.716
Output voltage line regulation (∆VO/VO)
(see Notes 2 and 3)
EN = VI,
UNIT
1.5
10 µA < IO < 250 mA, TJ = 25°C
IO = 250 mA,
TJ = –40°C to 125°C
Output current Limit
MAX
VO
Quiescent current ((GND current))
EN = 0V, (see Note 2)
Output noise voltage
range,
%VO
%VO
0.4
V
1
µA
1
1
µA
NOTE: 2. Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
5
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
electrical characteristics over recommended operating free-air temperature
Vi = VO(typ) + 1 V, IO = 10 µA, EN = 0 V, CO = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
TPS76628
IO = 250 mA,
IO = 250 mA,
TJ = 25°C
TJ = –40°C to 125°C
310
TPS76630
IO = 250 mA,
IO = 250 mA,
TJ = 25°C
TJ = –40°C to 125°C
270
TPS76633
IO = 250 mA,
IO = 250 mA,
TJ = 25°C
TJ = –40°C to 125°C
230
TPS76650
IO = 250 mA,
IO = 250 mA,
TJ = 25°C
TJ = –40°C to 125°C
140
Dropout voltage
g
(See Note 4)
NOTES: 3. If VO ≤ 1.8 V then Vimin = 2.7 V, Vimax = 10 V:
Line Reg. (mV)
+ ǒ%ńVǓ
V
O
If VO ≥ 2.5 V then Vimin = VO + 1 V, Vimax = 10 V:
Line Reg. (mV) + ǒ%ńVǓ
V
O
ǒ
V
ǒ
* 2.7 V
imax
100
V
imax
*
ǒ
V
O
Ǔ
MAX
UNIT
540
470
mV
400
250
1000
)1 V
100
range,
ǓǓ
1000
4. IN voltage equals VO(Typ) – 100 mV; TPS76601 output voltage set to 3.3 V nominal with external resistor divider. TPS76615,
TPS76618, TPS76625, and TPS76627 dropout voltage limited by input voltage range limitations (i.e., TPS76630 input voltage
needs to drop to 2.9 V for purpose of this test).
Table of Graphs
FIGURE
vs Load current
2, 3
vs Free-air temperature
4, 5
vs Load current
6, 7
vs Free-air temperature
8, 9
Power supply ripple rejection
vs Frequency
10
Output spectral noise density
vs Frequency
11
Output impedance
vs Frequency
12
Dropout voltage
vs Free-air temperature
Output voltage
Ground current
Line transient response
13, 14
15, 17
Load transient response
16, 18
Output voltage
vs Time
19
Dropout voltage
vs Input voltage
20
Equivalent series resistance (ESR)
vs Output current
21 – 24
Equivalent series resistance (ESR)
vs Added ceramic capacitance
25, 26
6
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TPS76615
TPS76633
OUTPUT VOLTAGE
vs
LOAD CURRENT
OUTPUT VOLTAGE
vs
LOAD CURRENT
1.494
3.304
VI = 4.3 V
TA = 25°C
1.493
3.300
VO – Output Voltage – V
VO – Output Voltage – V
3.302
3.298
3.296
3.294
1.492
1.491
1.490
1.489
3.292
1.488
3.29
1.487
0
50
100
150
200
VI = 2.7 V
TA = 25°C
0
250
50
100
IL – Load Current – mA
Figure 2
200
250
Figure 3
TPS76633
TPS76615
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
1.505
3.310
3.305
150
IL – Load Current – mA
IO = 10 µA
VI = 4.3 V
VI = 2.7 V
1.500
IO = 10 µA
VO – Output Voltage – V
VO – Output Voltage – V
3.300
3.295
IO = 250 mA
3.290
3.285
3.280
1.495
IO = 250 mA
1.490
1.485
3.275
1.480
3.270
3.265
–50
–25
0
25
50
75
100
125
150
1.475
–50
–25
TA – Free-Air Temperature – °C
25
50
75
100
125
150
TA – Free-Air Temperature – °C
Figure 4
Figure 5
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
0
• DALLAS, TEXAS 75265
7
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TPS76633
TPS76615
GROUND CURRENT
vs
LOAD CURRENT
GROUND CURRENT
vs
LOAD CURRENT
35.0
34.0
VO = 3.3 V
TA = 25°C
VO = 1.5 V
TA = 25°C
33.9
34.8
I GND – Ground Current – µ A
I GND – Ground Current – µ A
34.9
34.7
34.6
34.5
34.4
34.3
34.2
34.1
33.8
33.7
33.6
33.5
33.4
33.3
33.2
33.1
34.0
33.0
0
25
50
75 100 125 150 175 200 225 250
0
25
IL – Load Current – mA
50
75 100 125 150 175 200 225 250
IL – Load Current – mA
Figure 7
TPS76633
TPS76615
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
55
55
50
50
45
I GND – Ground Current – µ A
I GND – Ground Current – µ A
Figure 6
40
35
30
25
20
15
10
–50
VO = 3.3 V
IO = 250 mA
0
45
40
35
30
25
20
50
100
150
VO = 1.5 V
IO = 250 mA
15
–50
TA – Free-Air Temperature – °C
Figure 8
8
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
0
50
100
TA – Free-Air Temperature – °C
Figure 9
• DALLAS, TEXAS 75265
150
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TPS76633
TPS76633
POWER SUPPLY RIPPLE REJECTION
vs
FREQUENCY
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
101
VI = 4.3 V
CO = 10 µF
IO = 250 mA
TA = 25°C
60
Output Spectral Noise Density – µV Hz
PSRR – Power Supply Ripple Rejection – dB
70
50
40
30
20
10
10.00
10
IO = 150 mA
IO = 1 mA
100
10–1
VI = 4.3 V
CO = 10 µF
TA = 25°C
10–2
100.00
100 1000.0010000.00
1k
10k 100000.00
100k 1000000.00
1M 10000000.0
10M
100
1k
f – Frequency – Hz
10k
100k
f – Frequency – Hz
Figure 10
Figure 11
TPS76633
OUTPUT IMPEDANCE
vs
FREQUENCY
101
Zo – Output Impedance – Ω
VI = 4.3 V
CO = 10 µF
TA = 25°C
100
IO = 1 mA
10–1
IO = 250 mA
10–2
10
100
1k
10k
100k
1M
f – Frequency – Hz
Figure 12
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
9
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TPS76650
TPS76633
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
100
100
VI = 4.9 V
VI = 3.2 V
IO = 250 mA
V DO – Output Voltage – V
V DO – Output Voltage – V
IO = 250 mA
10–1
IO = 150 mA
IO = 50 mA
10–2
IO = 10 mA
10–3
IO = 150 mA
10–1
IO = 50 mA
IO = 10 mA
10–2
10–3
–50
–25
0
25
50
75
100
125
150
–50
–25
TA – Free-Air Temperature – °C
0
25
50
75
100
125
150
TA – Free-Air Temperature – °C
Figure 13
Figure 14
TPS76615
TPS76615
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
Output Voltage – mV
400
CL = 4.7 µF
TA = 25°C
100
50
0
I O – Output Current – mA
VI – Input Voltage – V
–50
3.7
2.7
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
200
0
CL = 4.7 µF
TA = 25°C
–200
–400
250
0
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
Figure 16
Figure 15
10
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TPS76633
TPS76633
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
Output Voltage – mV
400
CL = 4.7 µF
TA = 25°C
100
50
0
I O – Output Current – mA
VI – Input Voltage – V
–50
–100
5.3
4.3
0
CL = 4.7 µF
TA = 25°C
200
0
–200
250
0
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
Figure 18
Figure 17
TPS76633
TPS76601
OUTPUT VOLTAGE
vs
TIME (AT STARTUP)
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
0.60
IO = 250 mA
3
0.50
2
V DO – Output Voltage – V
VO– Output Voltage – V
4
1
Enable Pulse – V
0
4.3
0.40
TA = 125°C
0.30
TA = 25°C
0.20
TA = –40°C
0.10
0
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
0.00
2.50
3.00
4.00
4.50
5.00
Figure 20
Figure 19
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
3.50
VI – Input Voltage – V
• DALLAS, TEXAS 75265
11
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
100.00
102
Maximum ESR
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
100.00
102
Region of Instability
10.00
101
Region of Stability
VI = 4.3 V
CO = 4.7 µF
VO = 3.3 V
TA = 25°C
1.00
100
Minimum ESR
–1
0.10
10
Region of Instability
Maximum ESR
Region of Instability
10.00
101
Region of Stability
0
1.00
10
VI = 4.3 V
CO = 4.7 µF
VO = 3.3 V
TA = 125°C
–1
0.10
10
Minimum ESR
Region of Instability
–2
10
0.01
–2
0.01
10
0
50
100
150
200
250
0
50
100
IO – Output Current – mA
Figure 21
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
250
102
ESR – Equivalent Series Resistance – Ω
Maximum ESR
ESR – Equivalent Series Resistance – Ω
200
Figure 22
100.00
102
Region of Instability
10.00
101
0
1.00
10
VI = 4.3 V
CO = 10 µF
VO = 3.3 V
TA = 25°C
–1
0.10
10
Region of Stability
Minimum ESR
Region of Instability
–2
0.01
10
150
IO – Output Current – mA
Maximum ESR
Region of Instability
101
Region of Stability
100
VI = 4.3 V
CO = 10 µF
VO = 3.3 V
TA = 125°C
10–1
Minimum ESR
Region of Instability
10–2
0
50
100
150
200
250
0
IO – Output Current – mA
50
100
150
200
250
IO – Output Current – mA
Figure 23
Figure 24
† Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to CO.
12
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
ADDED CERAMIC CAPACITANCE
EQUIVALENT SERIES RESISTANCE†
vs
ADDED CERAMIC CAPACITANCE
10.00
101
VI = 4.3 V
CO = 4.7 µF
VO = 3.3 V
IO = 250 mA
TA = 25°C
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
10.00
101
0
1.00
10
Region of Stability
–1
100.10
Minimum ESR
Region of Instability
VI = 4.3 V
CO = 10 µF
VO = 3.3 V
IO = 250 mA
TA = 25°C
0
1.00
10
Region of Stability
–1
100.10
Minimum ESR
Region of Instability
–2
100.01
–2
100.01
0
0.2
0.4
0.6
0.8
1.0
0
Added Ceramic Capacitance – µF
0.4
0.6
0.8
1.0
Added Ceramic Capacitance – µF
Figure 25
VI
0.2
Figure 26
To Load
IN
OUT
+
EN
CO
GND
RL
ESR
Figure 27. Test Circuit for Typical Regions of Stability (Figures 21 through 24) (Fixed Output Options)
† Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to CO.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
13
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
APPLICATION INFORMATION
The TPS766xx family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V,
3.3 V, and 5.0 V), and an adjustable regulator, the TPS76601 (adjustable from 1.25 V to 5.5 V).
device operation
The TPS766xx features very low quiescent current, which remains virtually constant even with varying loads.
Conventional LDO regulators use a pnp pass element, the base current of which is directly proportional to the
load current through the regulator (IB = IC/β). The TPS766xx uses a PMOS transistor to pass current; because
the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range.
Another pitfall associated with the pnp-pass element is its tendency to saturate when the device goes into
dropout. The resulting drop in β forces an increase in IB to maintain the load. During power up, this translates
to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered systems,
it means rapid battery discharge when the voltage decays below the minimum required for regulation. The
TPS766xx quiescent current remains low even when the regulator drops out, eliminating both problems.
The TPS766xx family also features a shutdown mode that places the output in the high-impedance state
(essentially equal to the feedback-divider resistance) and reduces quiescent current to 1 µA (typ). If the
shutdown feature is not used, EN should be tied to ground. Response to an enable transition is quick; regulated
output voltage is reestablished in typically 160 µs.
minimum load requirements
The TPS766xx family is stable even at zero load; no minimum load is required for operation.
FB - pin connection (adjustable version only)
The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option . The output
voltage is sensed through a resistor divider network to close the loop as it is shown in Figure 29. Normally, this
connection should be as short as possible; however, the connection can be made near a critical circuit to
improve performance at that point. Internally, FB connects to a high-impedance wide-bandwidth amplifier and
noise pickup feeds through to the regulator output. Routing the FB connection to minimize/avoid noise pickup
is essential.
external capacitor requirements
An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047 µF or larger) improves
load transient response and noise rejection if the TPS766xx is located more than a few inches from the power
supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Like all low dropout regulators, the TPS766xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 4.7 µF and the ESR
(equivalent series resistance) must be between 300-mΩ and 20-Ω. Capacitor values 4.7 µF or larger are
acceptable, provided the ESR is less than 20 Ω. Solid tantalum electrolytic, aluminum electrolytic, and multilayer
ceramic capacitors are all suitable, provided they meet the requirements described previously.
14
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
APPLICATION INFORMATION
external capacitor requirements (continued)
TPS766xx
5
VI
IN
PG
6
NC/FB
IN
OUT
0.1 µF
4
EN
OUT
2
PG
1
250 kΩ
7
VO
8
+
GND
3
CO
4.7 µF
300 mΩ
Figure 28. Typical Application Circuit (Fixed Versions)
programming the TPS76601 adjustable LDO regulator
The output voltage of the TPS76601 adjustable regulator is programmed using an external resistor divider as
shown in Figure 29. The output voltage is calculated using:
V
O
ǒ) Ǔ
+ Vref
R1
R2
1
(1)
Where
Vref = 1.224 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 169 kΩ to set the divider current at 7 µA and then calculate R1 using:
R1
+
ǒ Ǔ
V
V
O
ref
*1
(2)
R2
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS76601
VI
0.1 µF
IN
PG
250 kΩ
≥ 2.0 V
≤ 0.8 V
OUTPUT
VOLTAGE
PG
EN
OUT
VO
R1
FB / NC
GND
R2
CO
R1
R2
UNIT
2.5 V
174
169
kΩ
3.3 V
287
169
kΩ
3.6 V
324
169
kΩ
4.0 V
383
169
kΩ
5.0 V
523
169
kΩ
300 mΩ
Figure 29. TPS76601 Adjustable LDO Regulator Programming
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
15
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
APPLICATION INFORMATION
power-good indicator
The TPS766xx features a power-good (PG) output that can be used to monitor the status of the regulator. The
internal comparator monitors the output voltage: when the output drops to between 92% and 98% of its nominal
regulated value, the PG output transistor turns on, taking the signal low. The open-drain output requires a pullup
resistor. If not used, it can be left floating. PG can be used to drive power-on reset circuitry or used as a
low-battery indicator.
regulator protection
The TPS766xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS766xx also features internal current limiting and thermal protection. During normal operation, the
TPS766xx limits output current to approximately 0.8 µA (typ). When current limiting engages, the output voltage
scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross
device failure, care should be taken not to exceed the power dissipation ratings of the package. If the
temperature of the device exceeds 150°C(typ), thermal-protection circuitry shuts it down. Once the device has
cooled below 130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
T max * T
J
A
+
D(max)
R
qJA
Where
TJmax is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package, i.e., 176°C/W for the 8-terminal
SOIC.
TA is the ambient temperature.
ǒ
Ǔ
The regulator dissipation is calculated using:
P
D
+ VI * VO
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
16
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS76615, TPS76618, TPS76625, TPS76627
TPS76628, TPS76630, TPS76633, TPS76650, TPS76601
ULTRA LOW QUIESCENT CURRENT 250-mA LOW-DROPOUT VOLTAGE REGULATORS
SLVS237 – AUGUST 1999
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
PINS **
0.050 (1,27)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.244 (6,20)
0.228 (5,80)
0.008 (0,20) NOM
0.157 (4,00)
0.150 (3,81)
1
Gage Plane
7
A
0.010 (0,25)
0°– 8°
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
0.004 (0,10)
4040047 / B 03/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Four center pins are connected to die mount pad.
Falls within JEDEC MS-012
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
17
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Powered by ICminer.com Electronic-Library Service CopyRight 2003