AD PKD01EY

a
FEATURES
Monolithic Design for Reliability and Low Cost
High Slew Rate: 0.5 V/␮s
Low Droop Rate
TA = 25ⴗC: 0.1 mV/ms
T A = 125ⴗC: 10 mV/ms
Low Zero-Scale Error: 4 mV
Digitally Selected Hold and Reset Modes
Reset to Positive or Negative Voltage Levels
Logic Signals TTL and CMOS Compatible
Uncommitted Comparator On-Chip
Available in Die Form
Monolithic Peak Detector
with Reset-and-Hold Mode
PKD01
FUNCTIONAL BLOCK DIAGRAM
+IN
–IN
OUTPUT
V+
V–
–
CMP
+
LOGIC
GND
V–
OUTPUT
BUFFER
DET
GATED
"gm"
AMP
–
–IN
–
D1
C
OUTPUT
+
A
+
+IN
–IN
–
+IN
+
GATED
"gm"
AMP
B
PKD01
GENERAL DESCRIPTION
The PKD01 tracks an analog input signal until a maximum
amplitude is reached. The maximum value is then retained as a
peak voltage on a hold capacitor. Being a monolithic circuit, the
PKD01 offers significant performance and package density
advantages over hybrid modules and discrete designs without
sacrificing system versatility. The matching characteristics
attained in a monolithic circuit provide inherent advantages
when charge injection and droop rate error reduction are
primary goals.
Innovative design techniques maximize the advantages of monolithic technology. Transconductance (gm) amplifiers were chosen
over conventional voltage amplifier circuit building blocks. The
gm amplifiers simplify internal frequency compensation, minimize
acquisition time and maximize circuit accuracy. Their outputs
are easily switched by low glitch current steering circuits. The
steered outputs are clamped to reduce charge injection errors
upon entering the hold mode or exiting the reset mode. The inherently low zero-scale error is further reduced by active Zener-Zap
trimming to optimize overall accuracy.
RST
RST
0
0
1
1
DET
0
1
1
0
OPERATIONAL MODE
PEAK DETECT
PEAK HOLD
RESET
INDETERMINATE
CH
SWITCHES SHOWN FOR:
RST = “0,” DET = “0”
The output buffer amplifier features an FET input stage to
reduce droop rate error during lengthy peak hold periods. A bias
current cancellation circuit minimizes droop error at high ambient temperatures.
Through the DET control pin, new peaks may either be detected
or ignored. Detected peaks are presented as positive output
levels. Positive or negative peaks may be detected without
additional active circuits, since Amplifier A can operate as an
inverting or noninverting gain stage.
An uncommitted comparator provides many application options.
Status indication and logic shaping/shifting are typical examples.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
PKD01–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V = ⴞ15 V, C
S
Parameter
gm AMPLIFIERS A, B
Zero-Scale Error
Input Offset Voltage
Input Bias Current
Input Offset Current
Voltage Gain
Open-Loop Bandwidth
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Slew Rate
Feedthrough Error1
Acquisition Time to
0.1% Accuracy1
Acquisition Time to
0.01% Accuracy1
= 1000 pF, TA = 25ⴗC, unless otherwise noted.)
PKD01A/E
Min Typ Max
Symbol Conditions
VZS
VOS
IB
IOS
AV
BW
CMRR
PSRR
VCM
SR
RL = 10 kΩ, VO = ± 10 V
AV = 1
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
∆VIN = 20 V, DET = 1, RST = 0
tAQ
tAQ
COMPARATOR
Input Offset Voltage
Input Bias Current
Input Offset Current
Voltage Gain
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Low Output Voltage
“OFF” Output Leakage Current
Output Short-Circuit Current
Response Time2
VOS
IB
IOS
AV
CMRR
PSRR
VCM
VOL
IL
ISC
tS
DIGITAL INPUTS – RST, DET2
Logic “1” Input Voltage
Logic “0” Input Voltage
Logic “1” Input Current
Logic “0” Input Current
VH
VL
IINH
IINL
MISCELLANEOUS
Droop Rate3
VDR
Output Voltage Swing:
Amplifier C
Short-Circuit Current:
Amplifier C
Switch Aperture Time
Switch Switching Time
Slew Rate: Amplifier C
Power Supply Current
H
VOP
ISC
tAP
ts
SR
ISY
18
80
86
± 10
66
20 V Step, AVCL = +1
20 V Step, AVCL = +1
2 kΩ Pull-Up Resistor to 5 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
ISINK ≤ 5 mA, Logic GND = 0 V
VOUT = 5 V
VOUT = 5 V
5 mV Overdrive, 2 kΩ Pull-Up
Resistor to 5 V
2
2
80
20
25
0.4
90
96
± 11
0.5
80
4
3
150
40
41
45
70
0.5
700
75
5
7.5
82
106
76
90
± 11.5 ± 12.5
–0.2 +0.15
25
7
12
150
10
74
76
± 10
66
1.5
1000
300
+0.4
80
45
2
VH = 3.5 V
VL = 0.4 V
0.02
1.6
TJ = 25°C
TA = 25°C
DET = 1
RL = 2.5 kΩ
0.01
0.02
0.07
0.15
± 11.5 ± 12.5
RL = 2.5 kΩ
No Load
3
3
80
20
25
0.4
90
96
± 11
0.5
80
7
6
250
75
mV
mV
nA
nA
V/mV
MHz
dB
dB
V
V/µs
dB
41
45
70
µs
µs
1
700
75
3.5
7.5
82
106
76
90
± 11.5 ± 12.5
–0.2 +0.15
25
7
12
150
3
mV
1000 nA
300 nA
V/mV
dB
dB
V
+0.4 V
80
µA
45
mA
ns
2
0.8
1
10
7
PKD01F
Min Typ Max Unit
15
75
50
2.5
5
40
7
0.02
1.6
0.8
1
10
V
V
µA
µA
0.01
0.03
0.1
0.20
mV/ms
mV/ms
± 11
± 12
7
15
75
50
2.5
6
V
40
9
mA
ns
ns
V/µs
mA
NOTES
1
Guaranteed by design.
2
DET = 1, RST = 0.
3
Due to limited production test times, the droop current corresponds to junction temperature (T J). The droop current vs. time (after power-on) curve clarified this point. Since
most devices (in use) are on for more than 1 second, ADI specifies droop rate for ambient temperature (T A) also. The warmed-up (T A) droop current specification is correlated
to the junction temperature (TJ) value. ADI has a droop current cancellation circuit that minimizes droop current at high temperature. Ambient (T A) temperature specifications
are not subject to production testing.
Specifications subject to change without notice.
–2–
REV. A
PKD01
ELECTRICAL CHARACTERISTICS
(@ VS = ⴞ15 V, CH = 1000 pF, –55ⴗC ≤ TA ≤ +125ⴗC for PKD01AY, –25ⴗC ≤ TA ≤ +85ⴗC for
PKD01EY, PKD01FY and 0ⴗC ≤ TA ≤ +70ⴗC for PKD01EP, PKD01FP, unless otherwise noted.)
Parameter
Symbol Conditions
PKD01A/E
PKD01F
Min Typ Max Min Typ Max
Unit
“gm” AMPLIFIERS A, B
Zero-Scale Error
Input Offset Voltage
Average Input Offset Drift1
Input Bias Current
Input Offset Current
Voltage Gain
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Slew Rate
Acquisition Time to 0.1% Accuracy1
VZS
VOS
TCVOS
IB
IOS
AV
CMRR
PSRR
VCM
SR
tAQ
4
3
–9
160
30
7.5 9
74 82
80 90
± 10 ± 11
0.4
60
COMPARATOR
Input Offset Voltage
Average Input Offset Drift1
Input Bias Current
Input Offset Current
Voltage Gain
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Low Output Voltage
OFF Output Leakage Current
Output Short-Circuit Current
Response Time
VOS
TCVOS
IB
IOS
AV
CMRR
PSRR
VCM
VOL
IL
ISC
tS
DIGITAL INPUTS – RST, DET
Logic “1” Input Voltage
Logic “0” Input Voltage
Logic “1” Input Current
Logic “0” Input Current
VH
VL
IINH
IINL
MISCELLANEOUS
Droop Rate3
VDR
RL = 10 kΩ, VO = ± 10 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
20 V Step, AVCL = +1
2
–4
1000
100
6.5
100
82
2 kΩ Pull-Up Resistor to 5 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
7
6
–24
250
100
5
72
70
± 10
2.5
–6
2000
600
4
2.5
80
80
72
72
± 11
± 11
ISINK ≤ 5 mA, Logic GND = 0 V –0.2 +0.15 +0.4 –0.2
VOUT = 5 V
25
100
VOUT = 5 V
6
10
45
6
5 mV Overdrive, 2 kΩ Pull-Up
Resistor to 5 V
200
6
5
–9
160
30
9
80
90
± 11
0.4
60
12
10
–24
500
150
mV
mV
µV/°C
nA
nA
V/mV
dB
dB
V
V/µs
µs
2
–4
1100
100
6.5
92
86
5
–6
2000
600
+0.15 +0.4
100 180
10
45
mV
µV/°C
nA
nA
V/mV
dB
dB
V
V
µA
mA
200
ns
2
Output Voltage Swing
Amplifier C
Short-Circuit Current
Amplifier C
Switch Aperture Time
Slew Rate: Amplifier C
Power Supply Current
VOP
ISC
tAP
SR
ISY
2
2
0.02
2.5
0.8
1
15
V
V
µA
µA
VH = 3.5 V
VL = 0.4 V
0.02
2.5
0.8
1
15
TJ = Max Operating Temp.
TA = Max Operating Temp.
DET = 1
1.2
10
3
15
mV/ms
2.4
20
6
20
mV/ms
± 11 ± 12
RL = 2.5 kΩ
6
RL = 2.5 kΩ
No Load
12
75
2
5.5
± 10.5 ± 12
40
8
6
12
75
2
6.5
V
40
10
mA
ns
V/µs
mA
NOTES
1
Guaranteed by design.
2
DET = 1, RST = 0.
3
Due to limited production test times, the droop current corresponds to junction temperature (T J ). The droop current vs. time (after power-on) curve clarifies this
point. Since most devices (in use) are on for more than 1 second, ADI specifies droop rate for ambient temperature (T A ) also. The warmed-up (T A ) droop current
specification is correlated to the junction temperature (T J) value. ADI has a droop current cancellation circuit that minimizes droop current at high temperature.
Ambient (T A ) temperature specifications are not subject to production testing.
Specifications subject to change without notice.
REV. A
–3–
PKD01
ABSOLUTE MAXIMUM RATINGS 1, 2
ORDERING GUIDE1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Input Voltage . . . . . . . . . . . . . . . . . . . Equal to Supply Voltage
Logic and Logic Ground
Voltage . . . . . . . . . . . . . . . . . . . . . . Equal to Supply Voltage
Output Short-Circuit Duration . . . . . . . . . . . . . . . . Indefinite
Amplifier A or B Differential Input Voltage . . . . . . . . . . ± 24 V
Comparator Differential Input Voltage . . . . . . . . . . . . . ± 24 V
Comparator Output Voltage
. . . . . . . . . . . . . . . . . . . . . . Equal to Positive Supply Voltage
Hold Capacitor Short-Circuit Duration . . . . . . . . . . Indefinite
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . 300°C
Storage Temperature Range
PKD01AY, PKD01EY, PKD01FY . . . . . –65°C to +150°C
PKD01EP, PKD01FP . . . . . . . . . . . . . . . –65°C to +125°C
Operating Temperature Range
PKD01AY . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
PKD01EY, PKD01FY . . . . . . . . . . . . . . . . –25°C to +85°C
PKD01EP, PKD01FP . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Junction Temperature . . . . . . . . . . . . . . . . . –65°C to +150°C
Model2
Temperature
Range
Package
Description
Package
Option
PKD01AY
PKD01EY
PKD01FY
PKD01EP
PKD01FP
–55°C to +85°C
–25°C to +85°C
–25°C to +85°C
0°C to 70°C
0°C to 70°C
Cerdip
Cerdip
Cerdip
Plastic DIP
Plastic DIP
Q-14
Q-14
Q-14
N-14
N-14
NOTES
1
Burn-in is available on commercial and industrial temperature range parts in
cerdip, plastic DIP, and TO-can packages.
2
For devices processed in total compliance to MIL-STD-883, add /883 after
part number. Consult factory for 883 data sheet.
PIN CONFIGURATION
DET
RST
V+
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.
2
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
LOGIC GND
OUTPUT
CH
COMP OUT
PKD01
–IN C
–IN A
+IN C
+IN A
–IN B
V–
+IN B
THERMAL CHARACTERISTICS
Package Type
␪JA*
␪JC
Unit
14-Lead Hermetic DIP (Y)
14-Lead Plastic DIP (P)
99
76
12
33
°C/W
°C/W
*θJA is specified for worst-case mounting conditions, i.e., θJA is specified for device
in socket for cerdip and PDIP packages.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the PKD01 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
DICE CHARACTERISTICS
–4–
REV. A
PKD01
WAFER TEST LIMITS (@ V = ⴞ15 V, C
S
H
= 1000 pF, TA = 25ⴗC, unless otherwise noted.)
Parameter
Symbol
“gm” AMPLIFIERS A, B
Zero-Scale Error
Input Offset Voltage
Input Bias Current
Input Offset Current
Voltage Gain
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Feedthrough Error
VZS
VOS
IB
IOS
AV
CMRR
PSRR
VCM
COMPARATOR
Input Offset Voltage
Input Bias Current
Input Offset Current
Voltage Gain1
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Low Output Voltage
“OFF” Output Leakage Current
Output Short-Circuit Current
VOS
IB
IOS
AV
CMRR
PSRR
VCM
VOL
IL
ISC
DIGITAL INPUTS–RST, DET2
Logic “1” Input Voltage
Logic “0” Input Voltage
Logic “1” Input Current
Logic “0” Input Current
VH
VL
IINH
IINL
MISCELLANEOUS
Droop Rate3
VDR
Conditions
RL = 10 kΩ, VO = ± 10 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
∆VIN = 20 V, DET = 1, RST = 0
2 kΩ Pull-Up Resistor to 5 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
ISINK ≤ 5 mA, Logic GND = 5 V
VOUT = 5 V
VOUT = 5 V
VH = 3.5 V
VL = 0.4 V
Unit
7
6
250
75
10
74
76
± 11.5
66
mV max
mV max
nA max
nA max
V/mV min
dB min
dB min
V min
dB min
3
1000
300
3.5
82
76
± 11.5
0.4
–0.2
80
45
7
mV max
nA max
nA max
V/mV min
dB min
dB min
V min
V max
V min
µA max
mA min
mA min
2
0.8
1
10
V min
V max
µA max
µA max
mV/ms max
mV/ms max
V min
mA max
mA min
mA max
Output Voltage Swing Amplifier C
Short-Circuit Current Amplifier C
VOP
ISC
Power Supply Current
ISY
No Load
0.1
0.20
± 11
40
7
9
SR
tA
tA
0.1% Accuracy, 20 V Step, AVCL = 1
0.01% Accuracy, 20 V Step, AVCL = 1
0.5
41
45
V/µs
µs
µs
5 mV Overdrive, 2 kΩ Pull-Up Resistor to 5 V
150
ns
RL = 2.5 kΩ
75
50
2.5
ns
ns
V/µs
gm AMPLIFIERS A, B
Slew Rate
Acquisition Time1
COMPARATOR
Response Time
MISCELLANEOUS
Switch Aperture Time
Switching Time
Buffer Slew Rate
tAP
tS
SR
TJ = 25°C,
TA = 25°C
RL = 2.5 kΩ
PKD01N
Limit
NOTES
1
Guaranteed by design.
2
DET = 1, RST = 0.
3
Due to limited production test times, the droop current corresponds to junction temperature (T J). The droop current vs. time (after power-on) curve clarifies this
point. Since most devices (in use) are on for more than 1 second, ADI specifies droop rate for ambient temperature (T A) also. The warmed-up (T A) droop current
specification is correlated to the junction temperature (T J) value. ADI has a droop current cancellation circuit that minimizes droop current at high temperature.
Ambient (TA) temperature specifications are not subject to production testing.
REV. A
–5–
PKD01–Typical Performance Characteristics
18
INPUT RANGE OF AMPLIFIER – V
35
6
2
–55ⴗC
+25ⴗC
–2
+125ⴗC
–6
–10
V– SUPPLY
30
2
A,B IOS – nA
INPUT + RANGE = V+
–55ⴗC TA +125ⴗC
OFFSET VOLTAGE – mV
4
10
0
9
12
15
6
SUPPLY VOLTAGE +V AND –V –V
TPC 1. A and B Input Range vs.
Supply Voltage
0
25 50 75 100 125 150
TEMPERATURE – ⴗC
TPC 3. A, B IOS vs. Temperature
1.0
100
VS = 15V
TA = 25ⴗC
AV = +1
+125ⴗC
+25ⴗC
0.5
100
RS = 10k⍀
RS = 0
10
10
ERROR – mV
RMS NOISE – ␮V
–55ⴗC
0
1
–0.5
0
0
1
10
100
FREQUENCY – Hz
1k
0.1
1
TPC 4. Input Spot Noise vs.
Frequency
TPC 5. Wideband Noise vs.
Bandwidth
1.0
18
POLARITY OF
ERROR MAY BE
POSITIVE OR
NEGATIVE
CH = 1000pF
TA = 25ⴗC
10
OUTPUT SWING – V
0
+125ⴗC
+25ⴗC
15
12.5
+125ⴗC
6
+25ⴗC
–55ⴗC
2
–55ⴗC
–2
+25ⴗC
–6
–10
–55ⴗC
–1.0
–10
RL = 10k⍀
V+ SUPPLY
+125ⴗC
V– SUPPLY
–14
10.0
7.5
5.0
2.5
0
–2.5
–5.0
–7.5
–10.0
–12.5
–15
–18
–5
0
VIN – V
5
TPC 7. Amplifier A Charge Injection Error vs. Input Voltage and
Temperature
10
4
9
12
15
6
SUPPLY VOLTAGE +V AND –V – V
18
TPC 8. Output Voltage Swing vs.
Supply Voltage (Dual Supply
Operation)
–6–
–5
0
VIN – V
5
10
TPC 6. Amplifier B Charge Injection Error vs. Input Voltage and
Temperature
14
0.5
–0.5
–1.0
–10
1000
10
100
BANDWIDTH – kHz
OUTPUT SWING – Volts
INPUT NOISE VOLTAGE – nV/ Hz
0
–75 –50 –25
100 125
TPC 2. A and B Amplifiers Offset
Voltage vs. Temperature
1000
15
5
–6
–75 –50 –25
0
25
50 75
TEMPERATURE – ⴗC
18
20
10
–14
4
25
–2
–4
–18
ERROR – mV
40
6
14
1.0
+25ⴗC
–55ⴗC
+125ⴗC
–55ⴗC
+25ⴗC
+125ⴗC
0.1
10.0
LOAD RESISTOR TO GROUND – k⍀
TPC 9. Output Voltage vs. Load
Resistance
REV. A
PKD01
12
CH = 1000pF
PEAK
OUTPUT
90
8
200mV ERROR
90
DETECTED
PEAK
4
10
0%
2␮s
10mV
10k
100k
1k
FREQUENCY – Hz
10mV
1M
TPC 10. Output Error vs.
Frequency and Input Voltage
TPC 11. Settling Response
TPC 12. Settling Response
90
0V
10
0%
OUTPUT VOLTAGE – 5V/DIV
100
100
90
0V
10
0%
TIME – 20␮s/DIV
100
GAIN
TA = 25ⴗC
10
0%
CH = 1000pF
GAIN – dB
TA = 25ⴗC
TA = 25ⴗC
0
CH = 1000pF
45
90
30
135
PHASE
180
10
0
0%
0V
–30
1
10
100
1k
10k 100k
FREQUENCY – Hz
1M
10M
TPC 17. Small-Signal Open-Loop
Gain/Phase vs. Frequency
–7–
TPC 15. Settling Time for –10 V to
0 V Step Input
120
TA = 25ⴗC
RL = 10k⍀
CL = 30pF
CH = 1000pF
60
90
REV. A
90
TIME – 20␮s/DIV
TPC 14. Large-Signal Noninverting
Response
90
TPC 16. Settling Time for +10 V to
0 V Step Input
0V
100
TIME – 20␮s/DIV
TPC 13. Large-Signal Inverting
Response
TIME – 20␮s/DIV
OUTPUT VOLTAGE – 5mV/DIV
TA = 25ⴗC
TA = 25ⴗC
CHANNEL-TO-CHANNEL ISOLATION – dB
0
100
10V
3kHz
SINEWAVE
INPUT
10
0%
2
OUTPUT VOLTAGE – 5V/DIV
CH = 1000pF
100
2mV ERROR
6
20mV ERROR
OUTPUT VOLTAGE – 5mV/DIV
2␮s
10mV
100
PHASE LAG – Degrees
PK OF SINEWAVE – V
10
TA = 25ⴗC
100
80
60
TEST CONDITION:
CH = 1000pF
AMPLIFIER A AND B CONNECTED IN +1 GAIN
40
20
AMPLIFIER A(B) OFF, INPUT = 20V p-p
AMPLIFIER B(B) ON, INPUT = 0V
0
1
10
100
1k
10k 100k
FREQUENCY – Hz
1M
TPC 18. Channel-to-Channel
Isolation vs. Frequency
10M
PKD01
100
ACQUISITION TIME TO 0.1% ACCURACY – ␮s
3
A, AV = +1
B, AV = ⴞ1
TA = 125ⴗC
CH = 1000pF
DROOP RATE – mV/ms
A, AV = –1
60
40
2
1
20
1
10
100
1k
10k 100k
FREQUENCY – Hz
1M
0
10M
TPC 19. Off Isolation vs. Frequency
)
%
.1
(0
)
1%
(0.
mV
0
1
V
TO
20
)
EP
.1%
ST
V (0
V
0
O 5m
1
T
P
TE
)
5V S
V (0.1%
P TO 1m
1V STE
EP
ST
200
100
80
60
40
20
0
TO
V
m
20
0
2000
4000
6000
8000
HOLD CAPACITANCE – pF
10000
TO 20mV
30
TO 2mV
20
TO 200mV
10
0
5
10
INPUT STEP – V
15
5V
1000
RESET
0V
10
5V
3kHz
SINEWAVE
INPUT
–10V
–10V
JUNCTION
TEMPERATURE
100
0
50
TEMPERATURE – ⴗC
500
100
5
5mV
5mV
1V
1V
90
4
+5
3
0
2
–5
1
TPC 24. Acquisition of Step Input
50ns
50ns
COMPARATOR
OUTPUT
COMPARATOR
OUTPUT
10
0%
0
100
5
5mV
5mV
50ns
50ns
COMPARATOR OUTPUT
COMPARATOR OUTPUT
90
+5
4
3
0
2
–5
1
10
0%
0
50␮s
TIME – 50ns/DIV
TPC 25. Acquisition of Sine
Wave Peak
0V
–10V
10V
–50
+10V
0%
TPC 23. Droop Rate vs. Temperature
OUTPUT VOLTAGE – V
+10V
0V
INPUT
10
10
1V
1V
90
50␮s
RESET
PEAK
OUTPUT
1
–100
DETECTED
PEAK
PEAK
DETECT
+10V
AMBIENT
TEMPERATURE
100
5V
CH = 1000pF
10V
RESET
90
20
TPC 22. Acquisition Time vs. Input
Voltage Step Size
0%
100
TPC 26. Comparator Output
Response Time (2 kΩ Pull-Up
Resistor, TA = 25 °C)
–8–
TIME – 50ns/DIV
TPC 27. Comparator Output
Response Time (2 kΩ Pull-Up
Resistor, TA = 25 °C)
REV. A
INPUT VOLTAGE – mV
40
SETTLING TIME – ␮s
300
TPC 21. Acquisition Time vs.
External Hold Capacitor and
Acquisition Step
TPC 20. Droop Rate vs. Time after
Power On
DROOP RATE (mV/sec), CH = 1000pF
TA = 25ⴗC
CH = 1000pF
100
2
3
4
5
6
7
8
9 10
1
TIME AFTER POWER APPLIED – Minutes
400
10000
50
0
0
INPUT VOLTAGE – mV
0
OUTPUT VOLTAGE – V
OFF ISOLATION – dB
80
500
PKD01
18
+VIN V+ FOR
–55ⴗC TA +125ⴗC
6
2
–55ⴗC
+25ⴗC
–2
+125ⴗC
–6
–10
V–
–14
–18
+125ⴗC
6
+25ⴗC
2
0
–2
–55ⴗC
ACCEPTABLE GROUND PIN
POTENTIAL IS BETWEEN
SLIDE LINES.
+25ⴗC
–6
–10
+125ⴗC
4
9
12
15
6
SUPPLY VOLTAGE +V AND –V – V
18
4
6
9
12
15
SUPPLY VOLTAGE +V AND –V – V
REJECTION RATIO – dB
80
+125ⴗC
POSITIVE SUPPLY
(+15V +1V SIN ␻T)
60
40
NEGATIVE SUPPLY
(–15V +1V SIN ␻)
CHANNEL A = 1
CHANNEL B = 0
3
6
9
12
SUPPLY +V AND –V – V
15
TPC 31. Supply Current vs. Supply
Voltage
3
110
2
100
1
0
–1
100 125
TPC 34. Comparator Offset Voltage
vs. Temperature
REV. A
1k
10k
FREQUENCY – Hz
100k
1M
0
1
2
3
LOGIC INPUT VOLTAGE – V
4
5
3
VS = ⴞ15V
TA = 25ⴗC
INPUT CURRENT
MUST BE LIMITED
TO LESS THAN 1mA
2
1
OTHER
INPUT
AT –10V
OTHER
INPUT
AT 0V
0
–1
–15
OTHER
INPUT
AT +10V
–10
–5
0
5
INPUT VOLTAGE – V
10
15
TPC 33. Comparator Input Bias
Current vs. Differential Input Voltage
1000
90
80
70
50
–75 –50 –25
–1
1200
800
600
400
60
–2
–3
–75 –50 –25
0
25
50 75
TEMPERATURE – ⴗC
100
TPC 32. Hold Mode Power Supply
Rejection vs. Frequency
COMPARATOR IOS – nA
OFFSET VOLTAGE – mV
0
10
18
COMPARATOR IB – nA
0
+25ⴗC
–2
TPC 30. Logic Input Current vs.
Logic Input Voltage
20
4
+125ⴗC
–3
–2
18
TA = 25ⴗC
VIN = 0V
CH = 1000pF
+25ⴗC
5
–1
LOGIC GROUND = 0V
100
–55ⴗC
–55ⴗC
LOGIC 0
TPC 29. Input Range of Logic
Ground vs. Supply Voltage
6
0
V–
–14
–18
TPC 28. Input Logic Range vs.
Supply Voltage
SUPPLY CURRENT – mA
LOGIC 1
10
INPUT BIAS CURRENT (EITHER INPUT) – ␮A
INPUT LOGIC RANGE – V
10
1
V+
14
LOGIC CURRENT – ␮A
INPUT RANGE OF LOGIC GROUND – V
18
14
0
25 50 75 100 125 150
TEMPERATURE – ⴗC
TPC 35. Comparator IOS vs.
Temperature
–9–
200
–75 –50 –25
0
25 50 75 100 125 150
TEMPERATURE – ⴗC
TPC 36. Comparator IB vs.
Temperature
14
V+
10
+125ⴗC
6
+25ⴗC
2
–55ⴗC
–2
+25ⴗC
–6
+125ⴗC
–10
V–
–14
–18
4
9
12
15
6
SUPPLY VOLTAGE +V AND –V – V
18
VO – VOLTAGE OUTPUT – V DC
1.0
0.8
+125ⴗC
0.6
+25ⴗC
0.4
0.2
–55ⴗC
0
–0.2
0
2
4
6
8
10
12
IO – OUTPUT SINK CURRENT – mA
TPC 40. Comparator Output
Voltage vs. Output Current and
Temperature
14
4
5
3
2
INVERTING INPUT = V IN
NONINVERTING INPUT = 0V
PULL-UP
RESISTOR = 2k⍀
TA = +25ⴗC
TA = –55ⴗC
TA = +125ⴗC
1
0
+5
–5
–50
VS = ⴞ15V
TA = 25ⴗC
4
3
2
RL = 2k⍀
TO 5V
RL = 1k⍀
TO 5V
1
0
0
50
100 150
TIME – ns
200
250
300
TPC 38. Comparator Response
Time vs. Temperature
INPUT VOLTAGE – mV OUTPUT VOLTAGE – V
TPC 37. Output Swing of Comparator vs. Supply Voltage
6
5
OUTPUT VOLTAGE – V
OUTPUT RANGE OF COMPARATOR – V
18
INPUT VOLTAGE – mV OUTPUT VOLTAGE – V
PKD01
0
–1.5
–1.0
–0.5
0
0.5
1.0
INPUT VOLTAGE – mV
1.5
2.0
TPC 39. Comparator Transfer
Characteristic
5
PULL-UP
RESISTOR = 2k⍀
4
3
TA = –55ⴗC
TA = +125ⴗC
2
TA = +25ⴗC
1
0
+5
0
–5
–50
0
50
100 150
TIME – ns
200
250
300
TPC 41. Comparator Response
Time vs. Temperature
–10–
REV. A
PKD01
THEORY OF OPERATION
The typical peak detector uses voltage amplifiers and a diode or
an emitter follower to charge the hold capacitor, CH, indirectionally (see Figure 1). The output impedance of A plus D1’s
dynamic impedance, rd, make up the resistance which determines the feedback loop pole. The dynamic impedance is
rd =
kT
, where Id is the capacitor charging current.
qI d
The pole moves toward the origin of the S plane as Id goes to
zero. The pole movement in itself will not significantly lengthen
the acquisition time since the pole is enclosed in the system
feedback loop.
only be: 2K – gm VIN. The net current into the hold capacitor
node then, is gmVIN [IH = 2I – (2I – gmVIN)]. In the hold mode,
Q2 and Q3 are ON while Q1 and Q4 are OFF. The net current
into the top of D1 is –I until D3 turns ON. With Q1 OFF, the
bottom of D2 is pulled up with a current I until D4 turns ON,
thus, D1 and D2 are reverse biased by <0.6 V, and charge injection is independent of input level.
The monolithic layout results in points A and B having equal
nodal capacitance. In addition, matched diodes D1 and D2 have
equal diffusion capacitance. When the transconductance amplifier outputs are switched open, points A and B are ramped
equally, but in opposite phase. Diode clamps D3 and D4 cause
the swings to have equal amplitudes. The net charge injection
(voltage change) at node C is therefore zero.
V+
VOUT (A) = V IN (A) ⴛ AV (A)
I
A
VIN
VOUT
R
+ OUT
2I
D3
A
D1
OUTPUT
C
VH
D1
rd
C
C
CH
INPUT
D4
D2
CH
B
Q1
Figure 1. Conventional Voltage Amplifier Peak Detector
When the moving pole is considered with the typical frequency
compensation of voltage amplifiers however, there is a loop stability
problem. The necessary compensation can increase the required
acquisition time. ADI’s approach replaces the input voltage amplifier with a transconductance amplifier (see Figure 2).
The PKD01 transfer function can be reduced to:
VOUT
=
VIN
VIN
Q2
6
Q3
A
Q4
B
gm V IN
3I
3I
LOGIC
CONTROL
A > B = PEAK DETECT
A < B = PEAK HOLD
V–
Figure 3. Transconductance Amplifier with Low Glitch
Current Switch
The peak transconductance amplifier, A is shown in Figure 4.
Unidirectional hold capacitor charging requires diode D1 to be
connected in series with the output. Upon entering the peak
hold mode D1 is reverse-biased. The voltage clamp limits charge
injection to approximately 1 pC and the hold step to 0.6 mV.
1
1
≈
1
sCH
sC
1+
+
1+ H
gm
gm ROUT
gm
where: gm ⬇ 1 µA/mV, ROUT ⬇ 20 MΩ.
The diode in series with A’s output (see Figure 2) has no effect
because it is a resistance in series with a current source. In
addition to simplifying the system compensation, the input
transconductance amplifier output current is switched by current steering. The steered output is clamped to reduce and match
any charge injection.
Minimizing acquisition time dictates a small CH capacitance. A
1000 pF value was selected. Droop rate was also minimized by
providing the output buffer with an FET input stage. A current cancellation circuit further reduces droop current and
minimizes the gate current’s tendency to double for every 10°
temperature change.
V+
I
2I
D3
IOUT (A) = V IN (A) ⴛ gm (A)
D1
A
IOUT
VIN
INPUT
ROUT
D1
C
VH
OUTPUT
D4
CH
VOUT
CH
Q1
VIN
Figure 2. Transconductance Amplifier Peak Detector
Q2
6
Q3
A
Q4
B
gm V IN
3I
Figure 3 shows a simplified schematic of the reset gm amplifier,
B. In the track mode, Q1 and Q4 are ON and Q2 and Q3 are
OFF. A current of 2I passes through D1, I is summed at B and
passes through Q1, and is summed with gmVIN. The current sink
can absorb only 3I, thus the current passing through D2 can
REV. A
C
rd
D2
3I
V–
LOGIC
CONTROL
A > B = PEAK DETECT
A < B = PEAK HOLD
Figure 4. Peak Detecting Transconductance Amplifier
with Switched Output
–11–
PKD01
A. Nulling Gated Output gm Amplifier A. Diode D1 must
be conducting to close the feedback circuit during amplifier A
VOS adjustment. Resistor network RA – RC cause D1 to conduct
slightly. With DET = 0 and VIN = 0 V, monitor the PKD01
output. Adjust the null potentiometer until VOUT = 0 V. After
adjustment, disconnect RC from CH.
APPLICATIONS INFORMATION
Optional Offset Voltage Adjustment
Offset voltage is the primary zero scale error component since a
variable voltage clamp limits voltage excursions at D1’s anode
and reduces charge injection. The PKD01 circuit gain and operational mode (positive or negative peak detection) determine the
applicable null circuit. Figures 5 through 8 are suggested circuits.
Each circuit also corrects amplifier C offset voltage error.
VS+
B. Nulling Gated gm Amplifier B. Set Amplifier B signal
input to VIN = 0 V and monitor the PKD01 output. Set DET =
1, RST = 1 and adjust the null potentiometer for VOUT = 0 V.
The circuit gain—inverting or noninverting—will determine which
null circuit illustrated in Figures 5 through 8 is applicable.
100k⍀
VS–
R2
2M⍀
R1
1k⍀
DET
0.1␮F
DET
D1
R1
1k⍀
VIN+
R2
R1
VIN
VS–
A
D1
R3
20k⍀
VOUT
C
A
VOUT
C
25k⍀
R4
20⍀
0.1␮F
VS+
–15V
PKD01
B
RC
2M⍀
RST
RA
200k⍀
RC
2M⍀
RB
1k⍀
CH
1000pF
–15V
PKD01
B
RA
200k⍀
RST
RB
CH
NOTES:
1k⍀
1000pF
R4
1. NULL RANGE = ⴞVS
R3
2. DISCONNECT RC FROM CH AFTER AMPLIFIER A ADJUSTMENT.
3. REPEAT NULL CIRCUIT FOR RESET BUFFER AMPLIFIER B IF REQUIRED.
NOTES:
1. NULL RANGE = ⴞVS R1
R2
2. DISCONNECT RC FROM CH AFTER AMPLIFIER A ADJUSTMENT.
3. REPEAT NULL CIRCUIT FOR RESET BUFFER AMPLIFIER B IF REQUIRED.
RA, RB AND RC NOT NECESSARY FOR AMPLIFIER B ADJUSTMENT.
( )
( )
Figure 7. VOS Null Circuit for Negative Peak Detector
Figure 5. VOS Null Circuit for Unity Gain Positive Peak
Detector
VS–
R2 = R3 + R4
VIN+
R1
VS+
DET
D1
A
R4
VOUT
VIN
VOUT
C
R4 = R2 R1
R1 + R2
R3
25k⍀
0.1␮F
R3
20⍀
R2
R1 + R3
VS+
D1
C
R5
20k⍀
0.1␮F
GAIN = 1 +
R2
A
R1
VS–
R1
25k⍀
DET
VIN–
R5
20k⍀
–15V
PKD01
B
R4
20⍀
B
RC
2M⍀
RA
200k⍀
RST
–15V
PKD01
RC
2M⍀
RA
200k⍀
RB
CH
1k⍀
1000pF
NOTES:
R1
1. NULL RANGE = ⴞVS R5
R4 R1 + R3
2. DISCONNECT RC FROM CH AFTER AMPLIFIER A ADJUSTMENT.
3. REPEAT NULL CIRCUIT FOR RESET BUFFER AMPLIFIER B IF REQUIRED.
RST
RB
CH
NOTES:
1k⍀
1000pF
R3
1. NULL RANGE = ⴞVS
R5
2. DISCONNECT RC FROM CH AFTER AMPLIFIER A ADJUSTMENT.
3. REPEAT NULL CIRCUIT FOR RESET BUFFER AMPLIFIER B IF REQUIRED.
Figure 6. VOS Null Circuit for Differential Peak Detector
Figure 8. VOS Null Circuit for Positive Peak Detector with
Gain
( )(
)
( )
–12–
REV. A
PKD01
PEAK HOLD CAPACITOR RECOMMENDATIONS
COMPARATOR
INPUT
The hold capacitor (CH) serves as the peak memory element
and compensating capacitor. Stable operation requires a minimum value of 1000 pF. Larger capacitors may be used to lower
droop rate errors, but acquisition time will increase.
VC
R1
PKD01
VOH
CMP
R2
Zero scale error is internally trimmed for CH = 1000 pF. Other
CH values will cause a zero scale shift which can be approximated with the following equation.
( )
∆VZS mV =
( ) − 0.6 mV
(nF )
1 × 103 pC
CH
The peak hold capacitor should have very high insulation resistance and low dielectric absorption. For temperatures below
85°C, a polystyrene capacitor is recommended, while a Teflon
capacitor is recommended for high temperature environments.
CAPACITOR GUARDING AND GROUND LAYOUT
Ground planes are recommended to minimize ground path
resistance. Separate analog and digital grounds should be used.
The two ground systems are tied together only at the common
system ground. This avoids digital currents returning to the
system ground through the analog ground path.
INVERTING
COMPARATOR
INPUT
DIGITAL
GND
V–
R1 = R2
( VV
C
)
–1
OH
Figure 10. Comparator Output with External Level-Setting
Resistors
Table I.
VC
VOH
R1
R2
5
5
15
15
15
15
3.5
5.0
3.5
5.0
7.5
10.0
2.7 kΩ
2.7 kΩ
4.7 kΩ
4.7 kΩ
7.5 kΩ
7.5 kΩ
6.2 kΩ
⬁
1.5 kΩ
2.4 kΩ
7.5 kΩ
15 kΩ
R1 ≈
VC
I SINK



1 
R2 ≈ 

 VC − 1

 VOH
1
14
13
PEAK DETECTOR LOGIC CONTROL (RST, DET)
2
PKD01
3
12
4
CH
11
10
5
9
6
8
7
REPEAT ON
“COMPONENT SIDE”
OF PC BOARD IF POSSIBLE
BOTTOM VIEW
The transconductance amplifier outputs are controlled by the
digital logic signals RST and DET. The PKD01 operational
mode is selected by steering the current (I1) through Q1 and Q2,
thus providing high-speed switching and a predictable logic
threshold. The logic threshold voltage is 1.4 V when digital
ground is at zero volts.
Other threshold voltages (VTH) may be selected by applying
the formula:
Figure 9. CH Terminal (Pin 4) Guarding. See Text.
VTH ≈ 1.4 V + Digital Ground Potential.
The CH terminal (Pin 4) is a high impedance point. To minimize
gain errors and maintain the PKD01’s inherently low droop rate,
guarding Pin 4 as shown in Figure 9 is recommended.
For proper operation, digital ground must always be at least
3.5 V below the positive supply and 2.5 V above the negative
supply. The RST or DET signal must always be at least 2.8 V
above the negative supply.
COMPARATOR
Operating the digital ground at other than zero volts does influence
the comparator output low voltage. The VOL level is referenced
to digital ground and will follow any changes in digital ground
potential:
The comparator output high level (VOH) is set by external resistors. It is possible to optimize noise immunity while interfacing
to all standard logic families—TTL, DTL, and CMOS. Figure
10 shows the comparator output with external level-setting
resistors. Table I gives typical R1 and R2 values for common
circuit conditions.
VOL ≈ 0.2 V + Digital Ground Potential.
The maximum comparator high output voltage (VOH) should be
limited to:
VOH (maximum) < V+ –2.0 V
With the comparator in the low state (VOL), the output stage
will be required to sink a current approximately equal to VC/R1.
REV. A
–13–
PKD01
V+
I1
DET OR RST
Q1
56k⍀
5%
I2
Q2
D
+18V
1
14
2
13
18k⍀
DIGITAL
GROUND
Q3
3
12
PKD01
5%
36k⍀
5%
V–
CURRENT TO
CONTROL MODES
Figure 11. Logic Control
4
11
5
10
6
9
7
8
–18V
Figure 12. Burn-In Circuit
Typical Circuit Configurations
V+
DET/RST
V–
D1
+10V
A
INPUT
INPUT
OUTPUT
C
0V
PKD01
+10V
OUTPUT
0V
RESET
VOLTAGE
A GAIN = +1
B GAIN = +1
B
TIME – 50␮s/DIV
CH
1000pF
Figure 13. Unity Gain Positive Peak Detector
V+
DET
10k⍀
1%
+5V
0V
–2V
+10V
INPUT
0V
OUTPUT
–4V
INPUT
(GAIN = +2)
5.1k⍀
5%
V–
D1
A
C
40.2k⍀
1%
10k⍀
5%
10k⍀
1%
RESET
VOLTAGE = +1V
(RESETS TO –4V)
OUTPUT
PKD01
B
A GAIN = +2
B GAIN = –4
8.2k⍀
5%
–10V
TIME – 50␮s/DIV
RST
CH
1000pF
Figure 14. Positive Peak Detector with Gain
–14–
REV. A
PKD01
V+
DET/RST
+2V
0V
INPUT
INPUT
(GAIN = –2)
10k⍀ 20k⍀
1%
1%
30.1k⍀
1%
C
8.2k⍀
5%
A GAIN = –2
B GAIN = +4
B
–4V
RESET
VOLTAGE = –1V
(RESETS TO –4V)
–10V
TIME – 50␮s/DIV
OUTPUT
PKD01
10k⍀
1%
0V
OUTPUT
D1
A
–5V
+10V
V–
7.5k⍀
5%
CH
1000pF
RST
Figure 15. Negative Peak Detector with Gain
V+
DET
INPUT
10k⍀
1%
VIN
0V
10k⍀
1%
V–
D1
A
OUTPUT
PKD01
+10V
OUTPUT
C
10k⍀
5%
–10V
RESET
VOLTAGE
0V
B
TIME – 50␮s/DIV
A GAIN = –1
B GAIN = +1
CH
1000pF
Figure 16. Unity Gain Negative Peak Detector
R2
R3
INPUT
RESET
VOLTAGE
IF BOTH INPUT SIGNAL (AMPLIFIER A INPUT) AND THE RESET
VOLTAGE (AMPLIFIER B INPUT) HAVE THE SAME POSITIVE
VOLTAGE GAIN, THE GAIN CAN BE SET BY A SINGLE VOLTAGE
DIVIDER FOR BOTH INPUT AMPLIFIERS.
OUTPUT
A
C
R4
R1
B
PKD01
CH
1000pF
INPUT AMPLIFIER GAIN
RESET AMPLIFIER GAIN
R3 = R4 =
= 1 + R2
R1
NOTE:
R1, R2, R3 AND R4 > 5k⍀
1
1 + 1
R1 R2
Figure 17. Alternate Gain Configuration
REV. A
–15–
PKD01
PKD01
POSITIVE
PEAK
DETECTOR
VPK+
VPK+
10k⍀
VPK– + V PK+
VIN
VIN
PKD01
NEGATIVE
PEAK
DETECTOR
VPK–
VOUT
OP27
10k⍀
VPK–
10k⍀
10k⍀
Figure 18. Peak-to-Peak Detector
POS/NEG
PEAK DETECTOR
+15V
10.5k⍀
+15V
–15V
OUTPUT
S2
R
S3
PKD01
SW-02
S1
S4
PEAK DETECTOR
RESET
R
CH
INPUT
1000pF
POLYSTYRENE
NOTES:
1. DEVICE IS RESET TO 0 VOLTS.
2. DETECTED PEAKS ARE PRESENTED AS POSITIVE OUTPUT LEVELS.
3. R = 10k⍀.
–15V
Figure 19. Logic Selectable Positive or Negative Peak Detector
DAC10
PORT 0
0
1
2
3
4
5
6
7
BIT 1
␮PROCESSOR
PORT 1
0
BIT 10
1
2
3
4
5
6
7
5V
R
2.7k⍀
CMP
R
D1
INPUT
SIGNAL
A
C
DET
RST
PKD01
B
RESET
VOLTAGE
CH
Figure 20. Peak Reading A/D Converter
–16–
REV. A
PKD01
5V
INPUT
A
VIN
VOUT
C
–15V +15V
RESET
PEAK
DETECT
VRS1
PKD01
B
VRS2
OUTPUT
VRS3
VRS4
2V
SW-201
A1
A2
A3
A4
+15V –15V ANALOG
GND
1ms
NOTES:
RESET VOLTAGE = –1.0V
TRACE 1 = 2V/DIV
TRACE 2 = 5V/DIV
TRACE 3 = 2V/DIV
LOGIC
GND
PK DET/RST
Figure 21. Positive Peak Detector with Selectable Reset Voltage
AMPLITUDE
SELECTION
LOGIC
DET
D1
A0 A1 A2
CH1
A
BUFFERED
RAMP
OUTPUT
C
CH2
CH3
RAMP
AMPLITUDE
CH4
CH5
MUX-08
B
RAMP SLOPE
SELECTION
PKD01
CH6
15V
CH7
RST
CH8
I
RAMP
AMPLITUDE
0
B8
CH
SLOPE =
~0.5V/␮s
B1
DAC08
RAMP START
PULSE
I0
SLOPE =
C
I1
C
~0.5V/␮s
RAMP
START
PULSE
NOTES:
1. NEGATIVE SLOPE OF RAMP IS SET BY DAC08 OUTPUT CURRENT.
2. DAC08 IS A DIGITALLY CONTROLLED CURRENT GENERATOR.
THE MAXIMUM FULL-SCALE CURRENT MUST BE LESS THAN 0.5mA.
Figure 22. Programmable Low Frequency Ramp Generator
REV. A
–17–
R > 20k⍀
REF-01
PKD01
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
C00481-0-2/01 (rev. A)
14-Lead Plastic DIP (PDIP)
(N-14)
0.795 (20.19)
0.725 (18.42)
14
8
1
0.280 (7.11)
0.240 (6.10)
7
PIN 1
0.100 (2.54)
BSC
0.060 (1.52)
0.015 (0.38)
0.325 (8.25)
0.300 (7.62)
0.210 (5.33)
MAX
0.130
(3.30)
0.160 (4.06)
MIN
0.115 (2.93)
0.022 (0.558) 0.070 (1.77) SEATING
PLANE
0.014 (0.356) 0.045 (1.15)
0.195 (4.95)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
14-Lead Cerdip
(Q-14)
0.005 (0.13) MIN 0.098 (2.49) MAX
14
8
PIN 1
1
7
0.100 (2.54) BSC
0.785 (19.94) MAX
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.320 (8.13)
0.290 (7.37)
0.060 (1.52)
0.015 (0.38)
0.150
(3.81)
MIN
SEATING
0.070 (1.78)
15°
PLANE
0°
0.030 (0.76)
0.015 (0.38)
0.008 (0.20)
PRINTED IN U.S.A.
0.200 (5.08)
MAX
0.310 (7.87)
0.220 (5.59)
–18–
REV. A