ETC LT1633IS

LT1632/LT1633
45MHz, 45V/µs, Dual/Quad
Rail-to-Rail Input and Output
Precision Op Amps
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTION
Gain-Bandwidth Product: 45MHz
Slew Rate: 45V/µs
Low Supply Current per Amplifier: 4.3mA
Input Common Mode Range Includes Both Rails
Output Swings Rail-to-Rail
Input Offset Voltage, Rail-to-Rail: 1350µV Max
Input Offset Current: 440nA Max
Input Bias Current: 2.2µA Max
Open-Loop Gain: 800V/mV Min
Low Input Noise Voltage: 12nV/√Hz Typ
Low Distortion: – 92dBc at 100kHz
Wide Supply Range: 2.7V to ±15V
Large Output Drive Current: 35mA Min
Dual in 8-Pin PDIP and SO Packages
U
APPLICATIONS
■
■
■
■
■
The LT ®1632/LT1633 are dual/quad, rail-to-rail input and
output op amps with a 45MHz gain-bandwidth product and
a 45V/µs slew rate.
The LT1632/LT1633 have excellent DC precision over the
full range of operation. Input offset voltage is typically less
than 400µV and the minimum open-loop gain of 0.8
million into a 10k load virtually eliminates all gain error.
Common mode rejection is typically 83dB over the full railto-rail input range when on a single 5V supply for excellent
noninverting performance.
The LT1632/LT1633 maintain their performance for supplies from 2.7V to 36V and are specified at 3V, 5V and ±15V
supplies. The inputs can be driven beyond the supplies
without damage or phase reversal of the output. The
output delivers load currents in excess of 35mA.
The LT1632 is available in 8-pin PDIP and SO packages
with the standard dual op amp pinout. The LT1633 features
the standard quad op amp configuration and is available in
a 14-pin plastic SO package. These devices can be used as
plug-in replacements for many standard op amps to
improve input/output range and performance.
Active Filters
Rail-to-Rail Buffer Amplifiers
Driving A/D Converters
Low Voltage Signal Processing
Battery-Powered Systems
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATION
Frequency Response
Single Supply, 40dB Gain, 550kHz Instrumentation Amplifier
50
40
30
R1
20k
–
R3
2k
1/2 LT1632
VIN–
+
R4
20k
3V
–
1/2 LT1632
VIN+
+
DIFFERENTIAL INPUT
20
VOLTAGE GAIN (dB)
R2
2k
R5
432Ω
VOUT
10
0
–10
COMMON MODE INPUT
–20
–30
–40
–50
1630/31 F02
VS = 3V
AV = 100
–60
–70
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
1632/33 TA02
sn1632 16323fs
1
LT1632/LT1633
W W
U
W
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Total Supply Voltage (V + to V –) ............................. 36V
Input Current ..................................................... ±10mA
Output Short-Circuit Duration (Note 2) ........ Continuous
Operating Temperature Range ................ – 40°C to 85°C
Specified Temperature Range (Note 4) ..... – 40°C to 85°C
Junction Temperature .......................................... 150°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
W
U
U
PACKAGE/ORDER INFORMATION
ORDER PART
NUMBER
TOP VIEW
OUT A 1
8
V+
– IN A 2
7
OUT B
6
– IN B
5
+ IN B
A
+ IN A 3
B
V– 4
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
14 OUT D
OUTA 1
13 – IN D
LT1632CN8
LT1632CS8
LT1632IN8
LT1632IS8
– IN A 2
– IN B 6
9
– IN C
S8 PART MARKING
OUT B 7
8
OUT C
TJMAX = 150°C, θJA = 130°C/ W (N8)
TJMAX = 150°C, θJA = 190°C/ W (S8)
ORDER PART
NUMBER
TOP VIEW
+ IN A 3
A
D
V+ 4
+ IN B 5
LT1633CS
LT1633IS
12 + IN D
11 V –
B
C
10 + IN C
S PACKAGE
14-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 150°C/ W
1632
1632I
Consult factory for Military and Industrial grade parts.
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
TYP
MAX
UNITS
= V+
MIN
VOS
Input Offset Voltage
VCM
VCM = V –
400
400
1350
1350
µV
µV
∆VOS
Input Offset Shift
VCM = V – to V +
350
1500
µV
500
2300
µV
1.15
– 1.15
2.2
0
µA
µA
2.3
4.4
µA
Input Offset Voltage Match (Channel-to-Channel) VCM
= V –, V + (Note 5)
IB
Input Bias Current
= V+
VCM
VCM = V –
∆IB
Input Bias Current Shift
VCM = V – to V +
0
– 2.2
= V + (Note 5)
Input Bias Current Match (Channel-to-Channel)
VCM
VCM = V – (Note 5)
50
50
880
880
nA
nA
IOS
Input Offset Current
VCM = V +
VCM = V –
40
40
440
440
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – to V +
80
880
nA
Input Noise Voltage
0.1Hz to 10Hz
400
nVP-P
en
Input Noise Voltage Density
f = 1kHz
12
nV/√Hz
in
Input Noise Current Density
f = 1kHz
1.6
pA/√Hz
CIN
Input Capacitance
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 300mV to 4.7V, RL = 10k
VS = 3V, VO = 300mV to 2.7V, RL = 10k
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = V – to V +
VS = 3V, VCM = V – to V +
5
450
350
70
66
pF
2000
1500
V/mV
V/mV
83
81
dB
dB
sn1632 16323fs
2
LT1632/LT1633
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
= V–
to V +
MIN
TYP
MAX
UNITS
CMRR Match (Channel-to-Channel) (Note 5)
VS = 5V, VCM
VS = 3V, VCM = V – to V +
65
61
85
82
dB
dB
Power Supply Rejection Ratio
VS = 2.7V to 12V, VCM = VO = 0.5V
82
100
dB
PSRR Match (Channel-to-Channel) (Note 5)
VS = 2.7V to 12V, VCM = VO = 0.5V
79
101
Minimum Supply Voltage (Note 9)
VCM = VO = 0.5V
2.6
2.7
VOL
Output Voltage Swing Low (Note 6)
No Load
ISINK = 0.5mA
ISINK = 25mA, VS = 5V
ISINK = 20mA, VS = 3V
15
32
600
500
30
60
1200
1000
mV
mV
mV
mV
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 0.5mA
ISOURCE = 20mA, VS = 5V
ISOURCE = 15mA, VS = 3V
16
42
910
680
40
80
1800
1400
mV
mV
mV
mV
ISC
Short-Circuit Current
VS = 5V
VS = 3V
IS
Supply Current per Amplifier
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
22
45
MHz
SR
Slew Rate (Note 8)
VS = 5V, AV = – 1, RL = Open, VO = 4V
VS = 3V, AV = – 1, RL = Open
13
11
27
22
V/µs
V/µs
tS
Settling Time
VS = 5V, AV = 1, RL = 1k,
0.01%, VSTEP = 2V
400
ns
PSRR
±20
±15
dB
±40
±30
4.3
V
mA
mA
5.2
mA
0°C < TA < 70°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
600
600
2000
2000
µV
µV
VOS TC
Input Offset Voltage Drift (Note 3)
VCM = V + – 0.1V
●
●
8
2.5
15
7
∆VOS
Input Offset Voltage Shift
VCM = V – + 0.2V to V + – 0.1V
●
400
2300
µV
700
3750
µV
1.3
– 1.3
2.6
0
µA
µA
Input Offset Voltage Match (Channel-to-Channel) VCM
= V – + 0.2V, V + – 0.1V (Note 5)
MIN
●
µV/°C
µV/°C
IB
Input Bias Current
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
∆IB
Input Bias Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
2.6
5.2
µA
Input Bias Current Match (Channel-to-Channel)
VCM = V + – 0.1V (Note 5)
VCM = V – + 0.2V (Note 5)
●
●
50
50
1040
1040
nA
nA
IOS
Input Offset Current
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
40
40
520
520
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
80
1040
nA
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 300mV to 4.7V, RL = 10k
VS = 3V, VO = 300mV to 2.7V, RL = 10k
●
●
300
200
1100
1000
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = V – + 0.2V to V + – 0.1V
VS = 3V, VCM = V – + 0.2V to V + – 0.1V
●
●
67
61
81
77
dB
dB
CMRR Match (Channel-to-Channel) (Note 5)
VS = 5V, VCM = V – + 0.2V to V + – 0.1V
VS = 3V, VCM = V – + 0.2V to V + – 0.1V
●
●
62
57
78
73
dB
dB
Power Supply Rejection Ratio
VS = 3V to 12V, VCM = VO = 0.5V
●
81
94
dB
PSRR Match (Channel-to-Channel) (Note 5)
VS = 3V to 12V, VCM = VO = 0.5V
●
77
95
PSRR
0
– 2.6
V/mV
V/mV
dB
sn1632 16323fs
3
LT1632/LT1633
ELECTRICAL CHARACTERISTICS
0°C < TA < 70°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Minimum Supply Voltage (Note 9)
VCM = VO = 0.5V
●
2.6
2.7
VOL
Output Voltage Swing Low (Note 6)
No Load
ISINK = 0.5mA
ISINK = 25mA, VS = 5V
ISINK = 20mA, VS = 3V
●
●
●
●
18
37
700
560
40
80
1400
1200
mV
mV
mV
mV
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 0.5mA
ISOURCE = 15mA, VS = 5V
ISOURCE = 10mA, VS = 3V
●
●
●
●
16
50
820
550
40
100
1600
1100
mV
mV
mV
mV
ISC
Short-Circuit Current
VS = 5V
VS = 3V
●
●
IS
Supply Current per Amplifier
±18
±13
±37
±26
4.9
●
mA
mA
6.0
mA
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
●
20
41
MHz
SR
Slew Rate (Note 8)
VS = 5V, AV = – 1, RL = Open, VO = 4V
VS = 3V, AV = – 1, RL = Open
●
●
13
10
26
21
V/µs
V/µs
– 40°C < TA < 85°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted. (Note 4)
SYMBOL PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
MIN
700
700
2400
2400
µV
µV
VOS TC
Input Offset Voltage Drift (Note 3)
VCM = V + – 0.1V
●
●
8
2.5
15
7
∆VOS
Input Offset Voltage Shift
VCM = V – + 0.2V to V + – 0.1V
µV/°C
µV/°C
●
475
2500
µV
Input Offset Voltage Match (Channel-to-Channel) VCM
= V – + 0.2V, V + (Note 5)
●
750
4000
µV
IB
Input Bias Current
= V + – 0.1V
VCM
VCM = V – + 0.2V
●
●
1.46
– 1.46
3.0
0
µA
µA
∆IB
Input Bias Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
2.92
6.0
µA
= V + – 0.1V (Note 5)
0
– 3.0
Input Bias Current Match (Channel-to-Channel)
VCM
VCM = V – + 0.2V (Note 5)
●
●
70
70
1160
1160
nA
nA
IOS
Input Offset Current
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
75
75
580
580
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
50
1160
nA
AVOL
Large-Signal Voltage Gain
VS = 5V, VO = 300mV to 4.7V, RL = 10k
VS = 3V, VO = 300mV to 2.7V, RL = 10k
●
●
250
200
1000
800
CMRR
Common Mode Rejection Ratio
VS = 5V, VCM = V – + 0.2V to V + – 0.1V
VS = 3V, VCM = V – + 0.2V to V + – 0.1V
●
●
65
60
80
75
dB
dB
CMRR Match (Channel-to-Channel) (Note 5)
VS = 5V, VCM = V – + 0.2V to V + – 0.1V
VS = 3V, VCM = V – + 0.2V to V + – 0.1V
●
●
62
57
78
73
dB
dB
Power Supply Rejection Ratio
VS = 3V to 12V, VCM = VO = 0.5V
●
79
95
dB
PSRR Match (Channel-to-Channel) (Note 5)
VS = 3V to 12V, VCM = VO = 0.5V
●
75
95
dB
Minimum Supply Voltage (Note 9)
VCM = VO = 0.5V
●
2.6
2.7
Output Voltage Swing Low (Note 6)
No Load
ISINK = 0.5mA
ISINK = 25mA, VS = 5V
ISINK = 20mV, VS = 3V
●
●
●
●
19
39
730
580
40
80
1500
1200
PSRR
VOL
V/mV
V/mV
V
mV
mV
mV
mV
sn1632 16323fs
4
LT1632/LT1633
ELECTRICAL CHARACTERISTICS
– 40°C < TA < 85°C, VS = 5V, 0V; VS = 3V, 0V; VCM = VOUT = half supply, unless otherwise noted. (Note 4)
SYMBOL PARAMETER
CONDITIONS
MIN
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 0.5mA
ISOURCE = 15mA, VS = 5V
ISOURCE = 10mA, VS = 3V
●
●
●
●
ISC
Short-Circuit Current
VS = 5V
VS = 3V
●
●
IS
Supply Current per Amplifier
±17
±12
TYP
MAX
UNITS
16
55
860
580
40
110
1700
1200
mV
mV
mV
mV
±36
±24
4.95
●
mA
mA
6.2
mA
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
●
20
40
MHz
SR
Slew Rate (Note 8)
VS = 5V, AV = –1, RL = Open, VO = 4V
VS = 3V, AV = –1, RL = Open
●
●
11
9
22
18
V/µs
V/µs
MIN
TA = 25°C, VS = ±15V, VCM = 0V, VOUT = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = V +
VCM = V –
500
500
2200
2200
µV
µV
∆VOS
Input Offset Voltage Shift
VCM = V – to V +
360
2200
µV
700
3500
µV
IB
Input Offset Voltage Match (Channel-to-Channel) VCM = V –, V + (Note 5)
Input Bias Current
VCM = V +
VCM = V –
1.15
– 1.15
2.2
0
µA
µA
∆IB
Input Bias Current Shift
2.3
4.4
µA
0
– 2.2
VCM = V – to V +
= V + (Note 5)
Input Bias Current Match (Channel-to-Channel)
VCM
VCM = V – (Note 5)
50
50
880
880
nA
nA
IOS
Input Offset Current
VCM = V +
VCM = V –
50
50
440
440
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – to V +
36
880
nA
Input Noise Voltage
0.1Hz to 10Hz
400
nVP-P
en
Input Noise Voltage Density
f = 1kHz
12
nV/√Hz
in
Input Noise Current Density
f = 1kHz
1.6
pA/√Hz
CIN
Input Capacitance
f = 100kHz
AVOL
Large-Signal Voltage Gain
VO = – 14.5V to 14.5V, RL = 10k
VO = – 10V to 10V, RL = 2k
800
400
5000
2500
V/mV
V/mV
Channel Separation
VO = – 10V to 10V, RL = 2k
110
127
dB
Common Mode Rejection Ratio
VCM = V – to V +
82
98
dB
= V–
80
101
dB
CMRR
CMRR Match (Channel-to-Channel) (Note 5)
VCM
to V +
3
pF
Power Supply Rejection Ratio
VS = ±5V to ±15V
82
96
dB
PSRR Match (Channel-to-Channel) (Note 5)
VS = ±5V to ±15V
80
101
dB
VOL
Output Voltage Swing Low (Note 6)
No Load
ISINK = 5mA
ISINK = 25mA
16
150
600
35
300
1200
mV
mV
mV
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 5mA
ISOURCE = 25mA
16
250
1200
40
500
2400
mV
mV
mV
PSRR
sn1632 16323fs
5
LT1632/LT1633
ELECTRICAL CHARACTERISTICS
TA = 25°C, VS = ±15V, VCM = 0V, VOUT = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
±35
±70
MAX
UNITS
ISC
Short-Circuit Current
IS
Supply Current per Amplifier
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
22
45
MHz
SR
Slew Rate
AV = – 1, RL = Open, VO = ±10V,
Measure at VO = ±5V
22
45
V/µs
tS
Settling Time
0.01%, VSTEP = 10V, AV = 1, RL = 1k
575
ns
4.6
mA
6
mA
0°C < TA < 70°C, VS = ±15V, VCM = 0V, VOUT = 0V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
= V + – 0.1V
VOS
Input Offset Voltage
VOS TC
Input Offset Voltage Drift (Note 3)
∆VOS
Input Offset Voltage Shift
IB
Input Offset Voltage Match (Channel-to-Channel) VCM = V – + 0.2V, V + – 0.1V (Note 5)
Input Bias Current
VCM = V + – 0.1V
VCM = V – + 0.2V
∆IB
Input Bias Current Shift
MIN
TYP
MAX
UNITS
µV
µV
VCM
VCM = V – + 0.2V
●
●
800
800
2750
2750
VCM = V + – 0.1V
●
●
10
5
17
11
VCM = V – + 0.2V to V + – 0.1V
●
500
2500
µV
●
800
4000
µV
1.3
– 1.3
2.6
0
µA
µA
●
●
0
– 2.6
µV/°C
µV/°C
VCM = V – + 0.2V to V + – 0.1V
●
2.6
5.2
µA
= V + – 0.1V (Note 5)
Input Bias Current Match (Channel-to-Channel)
VCM
VCM = V – + 0.2V (Note 5)
●
●
70
70
1040
1040
nA
nA
IOS
Input Offset Current
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
70
70
520
520
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
140
1040
nA
AVOL
Large-Signal Voltage Gain
VO = – 14.5V to 14.5V, RL = 10k
VO = – 10V to 10V, RL = 2k
●
●
600
300
4000
2000
V/mV
V/mV
Channel Separation
VO = – 10V to 10V, RL = 2k
CMRR
PSRR
●
110
125
dB
Common Mode Rejection Ratio
VCM
+ 0.2V to V + – 0.1V
●
81
96
dB
CMRR Match (Channel-to-Channel) (Note 5)
VCM = V – + 0.2V to V + – 0.1V
●
77
95
dB
Power Supply Rejection Ratio
VS = ±5V to ±15V
●
80
94
dB
74
= V–
PSRR Match (Channel-to-Channel) (Note 5)
VS = ±5V to ±15V
●
VOL
Output Voltage Swing Low (Note 6)
No Load
ISINK = 5mA
ISINK = 25mA
●
●
●
21
180
680
45
350
1400
mV
mV
mV
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 5mA
ISOURCE = 25mA
●
●
●
15
300
1400
40
600
2800
mV
mV
mV
ISC
Short-Circuit Current
●
IS
Supply Current per Amplifier
●
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
●
20
41
MHz
SR
Slew Rate
AV = – 1, RL = Open, VO = ±10V,
Measured at VO = ±5V
●
21
43
V/µs
±28
95
dB
±57
5.2
mA
6.9
mA
sn1632 16323fs
6
LT1632/LT1633
ELECTRICAL CHARACTERISTICS
– 40°C < TA < 85°C, VS = ±15V, VCM = 0V, VOUT = 0V, unless otherwise noted. (Note 4)
SYMBOL PARAMETER
VOS
Input Offset Voltage
VOS TC
Input Offset Voltage Drift (Note 3)
∆VOS
Input Offset Voltage Shift
CONDITIONS
MIN
= V+
TYP
MAX
UNITS
µV
µV
VCM
– 0.1V
VCM = V – + 0.2V
●
●
1000
1000
3000
3000
VCM = V + – 0.1V
●
●
10
5
17
11
VCM = V – + 0.2V to V + – 0.1V
●
500
2600
µV
●
850
4000
µV
1.4
– 1.4
2.8
0
µA
µA
= V – + 0.2V, V + – 0.1V (Note 5)
IB
Input Offset Voltage Match (Channel-to-Channel) VCM
Input Bias Current
VCM = V + – 0.1V
VCM = V – + 0.2V
∆IB
Input Bias Current Shift
●
●
0
– 2.8
µV/°C
µV/°C
VCM = V – + 0.2V to V + – 0.1V
●
2.8
5.6
µA
= V + – 0.1V (Note 5)
Input Bias Current Match (Channel-to-Channel)
VCM
VCM = V – + 0.2V (Note 5)
●
●
75
75
1120
1120
nA
nA
IOS
Input Offset Current
VCM = V + – 0.1V
VCM = V – + 0.2V
●
●
60
60
560
560
nA
nA
∆IOS
Input Offset Current Shift
VCM = V – + 0.2V to V + – 0.1V
●
120
1120
AVOL
Large-Signal Voltage Gain
VO = – 14.5V to 14.5V, RL = 10k
VO = – 10V to 10V, RL = 2k
●
●
500
250
5000
1800
V/mV
V/mV
Channel Separation
VO = – 10V to 10V, RL = 2k
●
110
124
dB
Common Mode Rejection Ratio
VCM = V – + 0.2V to V + – 0.1V
●
81
96
dB
●
77
95
dB
CMRR
CMRR Match (Channel-to-Channel) (Note 5)
VCM
= V – + 0.2V to V +
– 0.1V
nA
Power Supply Rejection Ratio
VS = ±5V to ±15V
●
80
93
dB
PSRR Match (Channel-to-Channel) (Note 5)
VS = ±5V to ±15V
●
74
95
dB
VOL
Output Voltage Swing Low (Note 6)
No Load
ISINK = 5mA
ISINK = 25mA
●
●
●
23
187
700
50
350
1400
mV
mV
mV
VOH
Output Voltage Swing High (Note 6)
No Load
ISOURCE = 5mA
ISOURCE = 25mA
●
●
●
16
300
1500
40
600
3000
mV
mV
mV
ISC
Short-Circuit Current
●
IS
Supply Current per Amplifier
●
PSRR
±27
±54
5.3
mA
7
mA
GBW
Gain-Bandwidth Product (Note 7)
f = 100kHz
●
20
40
MHz
SR
Slew Rate
AV = – 1, RL = Open, VO = ±10V,
Measure at VO = ±5V
●
18
35
V/µs
The ● denotes specifications that apply over the full operating temperature
range.
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 3: This parameter is not 100% tested.
Note 4: The LT1632C/LT1633C are guaranteed to meet specified
performance from 0°C to 70°C and are designed, characterized and
expected to meet these extended temperature limits, but are not tested at
– 40°C and 85°C. Guaranteed I grade parts are available, consult factory.
Note 5: Matching parameters are the difference between amplifiers A and
D and between B and C on the LT1633; between the two amplifiers on the
LT1632.
Note 6: Output voltage swings are measured between the output and
power supply rails.
Note 7: VS = 3V, VS = ±15V GBW limit guaranteed by correlation to
5V tests.
Note 8: VS = 3V, VS = 5V slew rate limit guaranteed by correlation to
±15V tests.
Note 9: Minimum supply voltage is guaranteed by testing the change of
VOS to be less than 250µV when the supply voltage is varied from 3V to
2.7V.
sn1632 16323fs
7
LT1632/LT1633
U W
TYPICAL PERFORMANCE CHARACTERISTICS
VOS Distribution, VCM = 0V
(PNP Stage)
VOS Distribution, VCM = 5V
(NPN Stage)
50
50
VS = 5V, 0V
VCM = 0V
VS = 5V, 0V
VCM = 5V
VS = 5V, 0V
30
20
10
40
PERCENT OF UNITS (%)
40
PERCENT OF UNITS (%)
40
30
20
10
0
–1250
–750
250
750
–250
INPUT OFFSET VOLTAGE (µV)
0
–1250
1250
–750
250
750
–250
INPUT OFFSET VOLTAGE (µV)
1632/33 G31
SUPPLY CURRENT PER AMPLIFIER (mA)
TA = 25°C
4.5
4.0
3.5
TA = –55°C
3.0
2.5
2.0
0
4
8 12 16 20 24 28
TOTAL SUPPLY VOTAGE (V)
1.5
VS = 5V, 0V
5.0
VS = ±15V
4.5
VS = 5V, 0V
4.0
3.5
3.0
1.0
0.5
0
–0.5
TA = 25°C
NPN ACTIVE
VS = ±15V
VCM = 15V
0
–0.4
PNP ACTIVE
VS = ±15V
VCM = – 15V
VS = 5V, 0V
VCM = 0V
–2.8
– 50 –35 – 20 –5 10 25 40 55 70 85 100
TEMPERATURE (°C)
1632/33 G04
0
2
3
4
5
1
COMMON MODE VOLTAGE (V)
6
Output Saturation Voltage vs Load
Current (Output High)
10
VS = 5V, 0V
VS = 5V, 0V
0.4
–1
1632/33 G03
10
VS = 5V, 0V
VCM = 5V
TA = – 55°C
–2.0
–2
100 125
TA = 125°C
–1.0
–1.5
Output Saturation Voltage vs Load
Current (Output Low)
SATURATION VOLTAGE (V)
INPUT BIAS CURRENT (µA)
5.5
Input Bias Current vs Temperature
1.2
–2.0
2.0
1632/33 G02
2.8
–1.2
6.0
2.5
25 50 75
–75 –50 –25 0
TEMPERATURE (°C)
32 36
1250
Input Bias Current vs
Common Mode Voltage
1630/31 G01
2.0
–750
250
750
–250
INPUT OFFSET VOLTAGE (µV)
1632/33 G33
SATURATION VOLTAGE (V)
SUPPLY CURRENT PER AMPLIFIER (mA)
5.0
0
–1250
1250
Supply Current vs Temperature
6.0
5.5
20
1632/33 G32
Supply Current vs Supply Voltage
TA = 125°C
30
10
INPUT BIAS CURRENT (µA)
PERCENT OF UNITS (%)
∆VOS Shift for VCM = 0V to 5V
50
1
TA = 125°C
0.1
TA = 25°C
TA = –55°C
0.01
0.01
0.1
1
10
LOAD CURRENT (mA)
100
1632/33 G05
1
TA = 125°C
0.1
TA = 25°C
TA = –55°C
0.01
0.01
0.1
1
10
LOAD CURRENT (mA)
100
1632/33 G06
sn1632 16323fs
8
LT1632/LT1633
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Minimum Supply Voltage
20
VS = 5V, 0V
400
300
TA = 25°C
200
TA = 125°C
TA = –55°C
50
40
VCM = 4.25V
NPN ACTIVE
30
20
100
VCM = 2.5V
PNP ACTIVE
10
12
10
8
4
2
3
TOTAL SUPPLY VOLTAGE (V)
5
4
45
40
0
30
GAIN
20
–45
50
60
40
GAIN BANDWIDTH
20
–180
15
10
–225
100
0
–135
–10
5
0
1632/33 G14
PSRR vs Frequency
CMRR vs Frequency
100
POWER SUPPLY REJECTION RATIO (dB)
120
110
VS = ±15V
VS = 5V, 0V
70
60
50
40
30
20
Channel Separation vs Frequency
80
70
POSITIVE SUPPLY
60
50
40
NEGATIVE SUPPLY
30
20
10
1632/33 G12
–50
–60
VS = ±15V
VOUT = ±10VP-P
RL = 2k
–70
–80
–90
–100
–110
–120
–130
0
10M
–40
VS = ±15V
90
0
30
15
20
25
10
TOTAL SUPPLY VOLTAGE (V)
1632/33 G11
1632/33 G08
100k
1M
FREQUENCY (Hz)
75
30
0
1
10
FREQUENCY (MHz)
60
PHASE MARGIN
30
–90
0.1
90
45
10
–20
0.01
TIME (1SEC/DIV)
90
PHASE
70
PHASE MARGIN (DEG)
50
80
VCM = VS /2
105
PHASE SHIFT (DEG)
VOLTAGE GAIN (dB)
60
120
GAIN BANDWIDTH (MHz)
70
10k
1000
Gain Bandwidth and Phase
Margin vs Supply Voltage
225
RL = 1k
VS = 3V, 0V 180
VS = ±15V 135
80
1k
10
100
FREQUENCY (Hz)
1632/33 G10
Gain and Phase vs Frequency
VS = 5V, 0V
VCM = VS /2
80
1
1000
11632/33 G09
0.1Hz to 10Hz
Output Voltage Noise
90
VCM = 2.5V
PNP ACTIVE
0
10
100
FREQUENCY (Hz)
1
1632/33 G07
100
VCM = 4.25V
NPN ACTIVE
6
2
CHANNEL SEPARATION (dB)
1
OUTPUT VOLTAGE (200nV/DIV)
14
0
0
COMMON MODE REJECTION RATIO (dB)
16
CURRENT NOISE (pA/√Hz)
500
VS = 5V, 0V
18
60
NOISE VOLTAGE (nV/√Hz)
CHANGE IN OFFSET VOLTAGE (µV)
Noise Current Spectrum
Noise Voltage Spectrum
70
600
1k
10k
100k
1M
FREQUENCY (Hz)
10M
1632/33 G13
–140
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
1632/33 G15
sn1632 16323fs
9
LT1632/LT1633
U W
TYPICAL PERFORMANCE CHARACTERISTICS
VS = 5V, 0V
AV = 1
RL = 1k
VOUT = 80% OF VS
AV = –1
50
60
50
45
RISING EDGE
40
FALLING EDGE
35
30
NONINVERTING
4
25
0
–2
–4
NONINVERTING
0
1000
4
8 12 16 20 24 28 32
TOTAL SUPPLY VOLTAGE (V)
Open-Loop Gain
Open-Loop Gain
RL = 10k
–5
15
150
10
100
5
RL = 10k
0
–5
–10
–10
–15
–15
15
RL = 1k
1
2
4
3
OUTPUT VOLTAGE (V)
–300
LT1633CS, VS = ±15V
–400
5
40 60 80 100 120 140 160
TIME AFTER POWER-UP (SEC)
1632/33 G22
1
0.1
3
2
7
1
VIN = 2VP-P
RL = 10k
VS = 3V, 0V
AV = 1
0.01
0.001
VS = 5V, 0V AND 3V, 0V
AV = –1
VS = 5V, 0V
AV = 1
VS = 5V, 0V
1
6
Total Harmonic Distortion + Noise
vs Frequency
AV = –1
4
5
1632/33 G21
AV = 1
0
20
–5 –4 –3 –2 –1 0 1 2 3 4
OUTPUT VOLTAGE (V)
6
THD + NOISE (%)
S8 PACKAGE, VS = ±15V
0
5
1632/33 G20
OUTPUT VOLTAGE SWING (VP-P)
N8 PACKAGE, VS = ±15V
LT1633CS, VS = 5V, 0V
–200
–50
Maximum Undistorted Output
Signal vs Frequency
N8 PACKAGE, VS = 5V, 0V
S8 PACKAGE, VS = 5V, 0V
–100
0
–200
0
Warm-Up Drift vs Time
0
50
–100
1632/33 G19
100
VS = ±15V
RL = 100Ω
–150
–20
20
INPUT VOLTAGE (µV)
INPUT VOLTAGE (µV)
RL = 1k
1.00
200
VS = 5V, 0V
10
– 20
0
5
–20 –15 –10 – 5
10
OUTPUT VOLTAGE (V)
0.25
0.75
0.50
SETTLING TIME (µs)
1632/33 G18
Open-Loop Gain
VS = ±15V
0
0
20
15
5
–10
36
1632/33 G17
1632/33 G16
20
INVERTING
–8
20
10
100
CAPACITIVE LOAD (pF)
1
INVERTING
2
–6
30
INPUT VOLTAGE (µV)
OUTPUT STEP (V)
70
40
CHANGE IN OFFSET VOLTAGE (µV)
VS = ±15V
8
6
SLEW RATE (V/µs)
80
OVERSHOOT (%)
10
55
90
–500
Output Step vs
Settling Time to 0.01%
Slew Rate vs Supply Voltage
Capacitive Load Handling
10
100
FREQUENCY (kHz)
1000
1630/31 G24
0.0001
0.1
1
10
FREQUENCY (kHz)
100
1632/33 G23
sn1632 16323fs
10
LT1632/LT1633
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Harmonic Distortion vs Frequency
5V Small-Signal Response
5V Large-Signal Response
HARMONIC DISTORTION (dBc)
0
–20
VS = 5V, 0V
AV = 1
VIN = 2VP-P
RL = 150Ω
RL = 1k
–40
3RD
–60
2ND
–80
VS = 5V, 0V
AV = 1
RL = 1k
3RD
–100
100
2ND
200
1000
500
FREQUENCY (kHz)
163233 G25
VS = 5V, 0V
AV = 1
RL = 1k
1632/33 G26
2000
1632/33 G29
±15V Small-Signal Response
Harmonic Distortion vs Frequency
±15V Large-Signal Response
HARMONIC DISTORTION (dBc)
0
–20
VS = 5V, 0V
AV = –1
VIN = 2VP-P
RL = 150Ω
RL = 1k
2ND
–40
3RD
–60
3RD
2ND
–80
–100
100
VS = ±15V
AV = 1
RL = 1k
200
1000
500
FREQUENCY (kHz)
1632/33 G27
VS = ±15V
AV = 1
RL = 1k
1632/33 G28
2000
1632/33
1000G30
U
W
U
U
APPLICATIONS INFORMATION
Rail-to-Rail Input and Output
The LT1632/LT1633 are fully functional for an input and
output signal range from the negative supply to the positive supply. Figure 1 shows a simplified schematic of the
amplifier. The input stage consists of two differential
amplifiers, a PNP stage Q1/Q2 and an NPN stage Q3/Q4
that are active over different ranges of input common
mode voltage. The PNP differential input pair is active for
input common mode voltages VCM between the negative
supply to approximately 1.5V below the positive supply.
As VCM moves closer toward the positive supply, the
transistor Q5 will steer the tail current I1 to the current
mirror Q6/Q7, activating the NPN differential pair and the
PNP pair becomes inactive for the rest of the input common mode range up to the positive supply.
The output is configured with a pair of complementary
common emitter stages Q14/Q15 that enables the output
to swing from rail to rail. These devices are fabricated on
Linear Technology’s proprietary complementary bipolar
process to ensure similar DC and AC characteristics.
Capacitors C1 and C2 form local feedback loops that lower
the output impedance at high frequencies.
Power Dissipation
The LT1632/LT1633 amplifiers combine high speed and
large output current drive in a small package. Because the
sn1632 16323fs
11
LT1632/LT1633
U
U
W
U
APPLICATIONS INFORMATION
V+
R3
+ IN
+
R6
225Ω
I1
R4
Q12
Q11
R5
D1
R7
– IN 225Ω
D6
D8
D5
D7
Q15
Q13
+
D2
Q5
I2
VBIAS
V–
Q4
Q3
Q1
C2
CC
OUT
Q2
D3
Q9
Q8
D4
Q7
BUFFER
AND
OUTPUT BIAS
C1
Q6
R1
V–
R2
Q14
1632/33 F01
Figure 1. LT1632 Simplified Schematic Diagram
amplifiers operate over a very wide supply range, it is
possible to exceed the maximum junction temperature of
150°C in plastic packages under certain conditions. Junction temperature TJ is calculated from the ambient temperature TA and power dissipation PD as follows:
LT1632CN8: TJ = TA + (PD • 130°C/W)
LT1632CS8: TJ = TA + (PD • 190°C/W)
LT1633CS: TJ = TA + (PD • 150°C/W)
The power dissipation in the IC is the function of the supply
voltage, output voltage and load resistance. For a given
supply voltage, the worst-case power dissipation PDMAX
occurs at the maximum supply current and when the
output voltage is at half of either supply voltage (or the
maximum swing if less than 1/2 supply voltage). Therefore PDMAX is given by:
PDMAX = (VS • ISMAX) + (VS/2)2/RL
To ensure that the LT1632/LT1633 are used properly,
calculate the worst-case power dissipation, use the thermal resistance for a chosen package and its maximum
junction temperature to derive the maximum ambient
temperature.
Example: An LT1632CS8 operating on ±15V supplies and
driving a 500Ω, the worst-case power dissipation per
amplifier is given by:
PDMAX = (30V • 5.6mA) + (15V – 7.5V)(7.5/500)
= 0.168 + 0.113 = 0.281W
If both amplifiers are loaded simultaneously, then the total
power dissipation is 0.562W. The SO-8 package has a
junction-to-ambient thermal resistance of 190°C/W in still
air. Therefore, the maximum ambient temperature that the
part is allowed to operate is:
TA = TJ – (PDMAX • 190°C/W)
TA = 150°C – (0.562W • 190°C/W) = 43°C
For a higher operating temperature, lower the supply
voltage or use the DIP package part.
Input Offset Voltage
The offset voltage changes depending upon which input
stage is active, and the maximum offset voltages are
trimmed to less than 1350µV. To maintain the precision
characteristics of the amplifier, the change of VOS over the
entire input common mode range (CMRR) is guaranteed
to be less than 1500µV on a single 5V supply.
Input Bias Current
The input bias current polarity depends on the input
common mode voltage. When the PNP differential pair is
active, the input bias currents flow out of the input pins.
sn1632 16323fs
12
LT1632/LT1633
U
W
U
U
APPLICATIONS INFORMATION
They flow in the opposite direction when the NPN input
stage is active. The offset voltage error due to input bias
currents can be minimized by equalizing the noninverting
and inverting input source impedance.
Output
The outputs of the LT1632/LT1633 can deliver large load
currents; the short-circuit current limit is 70mA. Take care
to keep the junction temperature of the IC below the
absolute maximum rating of 150°C (refer to the Power
Dissipation section). The output of these amplifiers have
reverse-biased diodes to each supply. If the output is
forced beyond either supply, unlimited current will flow
through these diodes. If the current is transient and limited
to several hundred mA, no damage to the part will occur.
Overdrive Protection
To prevent the output from reversing polarity when the
input voltage exceeds the power supplies, two pairs of
crossing diodes D1 to D4 are employed. When the input
voltage exceeds either power supply by approximately
700mV, D1/D2 or D3/D4 will turn on, forcing the output to
the proper polarity. For this phase reversal protection to
work properly, the input current must be limited to less
than 5mA. If the amplifier is to be severely overdriven, an
external resistor should be used to limit the overdrive
current.
The LT1632/LT1633’s input stages are also protected
against large differential input voltages by a pair of backto-back diodes D5/D8. When a differential voltage of
more than 1.4V is applied to the inputs, these diodes will
turn on, preventing the emitter-base breakdown of the
input transistors. The current in D5/D8 should be limited
to less than 10mA. Internal 225Ω resistors R6 and R7 will
limit the input current for differential input signals of 4.5V
or less. For larger input levels, a resistor in series with
either or both inputs should be used to limit the current.
Worst-case differential input voltage usually occurs when
the output is shorted to ground. In addition, the amplifier
is protected against ESD strikes up to 3kV on all pins.
Capacitive Load
The LT1632/LT1633 are wideband amplifiers that can
drive capacitive loads up to 200pF on ±15V supplies in a
unity-gain configuration. On a 3V supply, the capacitive
load should be kept to less than 100pF. When there is a
need to drive larger capacitive loads, a resistor of 20Ω to
50Ω should be connected between the output and the
capacitive load. The feedback should still be taken from the
output so that the resistor isolates the capacitive load to
ensure stability.
Feedback Components
The low input bias currents of the LT1632/LT1633 make it
possible to use the high value feedback resistors to set the
gain. However, care must be taken to ensure that the pole
formed by the feedback resistors and the total capacitance
at the inverting input does not degrade stability. For
instance, the LT1632/LT1633 in a noninverting gain of 2,
set with two 20k resistors, will probably oscillate with
10pF total input capacitance (5pF input capacitance and
5pF board capacitance). The amplifier has a 6MHz crossing frequency and a 55° phase margin at 6dB of gain. The
feedback resistors and the total input capacitance form a
pole at 1.6MHz that induces a phase shift of 75° at 5MHz!
The solution is simple: either lower the value of the
resistors or add a feedback capacitor of 10pF or more.
U
TYPICAL APPLICATIONS
Single Supply, 40dB Gain, 550kHz Instrumentation
Amplifier
An instrumentation amplifier with a rail-to-rail output
swing, operating from a 3V supply can be constructed with
the LT1632 as shown in the first page of this data sheet.
The amplifier has a nominal gain of 100, which can be
adjusted with resistor R5. The DC output level is set by the
difference of the two inputs multiplied by the gain of 100.
The voltage gain and the DC output level can be
expressed as follows:
sn1632 16323fs
13
LT1632/LT1633
U
TYPICAL APPLICATIONS
R4  R2 R3 + R2 
1+
AV =
+
R3  R1
R5 
−
 +
VOUT =  VIN − VIN  • AV


10
0
–10
GAIN (dB)
–20
Common mode range can be calculated by the following
equations:
–30
–40
–50
–60
–70
VS = 3V, 0V
VIN = 2.5VP-P
–80
Lower limit common mode input voltage
 V  R2
 1.0
+ 0.1V
VCML =  OUT 
 AV  R5
 1.1
Upper limit common mode input voltage
 V  R2
 1.0
+ VS − 0.15V 
VCMH =  OUT 
 AV  R5
 1.1
where VS is supply voltage.
(
–90
0.1k
1k
10k
100k
FREQUENCY (Hz)
1M
10M
1632/33 F03
Figure 3. Frequency Response
)
With a 2.25VP-P, 100kHz input signal on a 3V supply, the
filter has harmonic distortion of less than – 87dBc.
RF Amplifier Control Biasing and DC Restoration
For example, the common mode range is from 0.15V to
2.65V if the output is set at one half of the 3V supply. The
common mode rejection is greater than 110dB at 100Hz
when trimmed with resistor R1. The amplifier has a
bandwidth of 550kHz.
Taking advantage of the rail-to-rail input and output, and
the large output current capability of the LT1632, the
circuit shown in Figure 4 provides precise bias current for
the RF amplifiers and restores the DC output level. To
ensure optimum performance of an RF amplifier, its bias
point must be accurate and stable over the operating
Single Supply, 400kHz, 4th Order Butterworth Filter
The circuit shown in Figure 2 makes use of the low voltage
operation and the wide bandwidth of the LT1632 to create
a 400kHz 4th order lowpass filter with a single supply. The
amplifiers are configured in the inverting mode to minimize common mode induced distortion and the output
can swing rail-to-rail for the maximum dynamic range.
Figure 3 displays the frequency response of the filter.
Stopband attenuation is greater than 85dB at 10MHz.
5V
R2
453Ω
5V
–
2.32k
6.65k
C1
0.01µF
+
HP-MSA0785
C3
1500pF
C6
0.01µF
L2
220µH
HP-MSA0785
RF2
RF1
+
C5
0.01µF
L1
220µH
–
2.74k
22pF
5.62k
–
470pF
1/2 LT1632
1/2 LT1632
+
L3
3.9µH
C4
1500pF
VOUT
L4
3.9µH
+
VOUT
+
VS/2
+
R3
10k
47pF
2.74k
220pF
Q2
2N3906
+
VIN
VIN
Q1
2N3906
A1
1/2 LT1632
C2
1500pF
2.32k
R4
10Ω
R1
10Ω
R5
50Ω
A2
1/2 LT1632
1632/33 F04
–
1632/33 F02
Figure 2. Single Supply, 400kHz, 4th Order Butterworth Filter
Figure 4. RF Amplifier Control Biasing and DC Restoration
sn1632 16323fs
14
LT1632/LT1633
U
TYPICAL APPLICATIONS
temperature range. The op amp A1 combined with Q1, Q2,
R1, R2 and R3 establishes two current sources of 21.5mA
to bias RF1 and RF2 amplifiers. The current of Q1, is
determined by the voltage across R2 over R1, which is
then replicated in Q2. These current sources are stable and
precise over temperature and have a low dissipated power
U
PACKAGE DESCRIPTION
due to a low voltage drop between their terminals. The
amplifier A2 is used to restore the DC level at the output.
With a large output current of the LT1632, the output can
be set at 1.5V DC on 5V supply and 50Ω load. This circuit
has a – 3dB bandwidth from 2MHz to 2GHz and a power
gain of 25dB.
Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.300 – 0.325
(7.620 – 8.255)
0.045 – 0.065
(1.143 – 1.651)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
(
+0.035
0.325 –0.015
+0.889
8.255
–0.381
)
0.400*
(10.160)
MAX
0.130 ± 0.005
(3.302 ± 0.127)
8
7
6
5
1
2
3
4
0.255 ± 0.015*
(6.477 ± 0.381)
0.125
(3.175) 0.020
MIN
(0.508)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
0.100 ± 0.010
(2.540 ± 0.254)
N8 1197
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.053 – 0.069
(1.346 – 1.752)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
0.406 – 1.270
0.014 – 0.019
(0.355 – 0.483)
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
7
8
5
6
0.004 – 0.010
(0.101 – 0.254)
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
0.050
(1.270)
TYP
1
3
2
4
SO8 0996
S Package
14-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.337 – 0.344*
(8.560 – 8.738)
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
14
0.053 – 0.069
(1.346 – 1.752)
0° – 8° TYP
0.016 – 0.050
0.406 – 1.270
0.014 – 0.019
(0.355 – 0.483)
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
13
12
11
10
9
8
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
TYP
0.228 – 0.244
(5.791 – 6.197)
0.150 – 0.157**
(3.810 – 3.988)
1
2
3
4
5
6
7
S14 0695
sn1632 16323fs
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1632/LT1633
U
TYPICAL APPLICATION
Tunable Q Notch Filter
A single supply, tunable Q notch filter as shown in Figure
5 is built with LT1632 to maximize the output swing. The
filter has a gain of 2, and the notch frequency (fO) is set by
the values of R and C. The resistors R10 and R11 set up the
DC level at the output. The Q factor can be adjusted by
varying the value of R8. The higher value of R8 will
decrease Q as depicted in Figure 6, because the output
induces less of feedback to amplifier A2. The value of R7
should be equal or greater than R9 to prevent oscillation.
If R8 is a short and R9 is larger than R7, then the positive
feedback from the output will create phase inversion at the
output of amplifier A2, which will lead to oscillation.
C
1000pF
C1
2.2µF
5V
40
R1
500Ω
R2
1k
R
1.62k
C
1000pF
A2
1/2 LT1632
+
R10
10k
C2
4.7µF
VOUT
1
2πRC
R = 1.62k
C = 1000pF
–
R6
R5
1k
1k
C5
4.7µF
–
5V
A1
1/2 LT1632
fO =
VO(DC) = 5V
R7
1k AV = 2
R11
= 2.5V
R11 + R10
20
INCREASING R8
0
–20
DECREASING R8
–40
R8
5k
R9
1k
GAIN (VOUT/VIN)(dB)
+
R
1.62k
VIN
0
1632/33 F05
20 40 60 80 100 120 140 160 180 200
FREQUENCY (kHz)
R11
10k
13632/33 F06
Figure 6. Frequency Response
Figure 5. Tunable Q Notch Filter
RELATED PARTS
PART NUMBER
DESCRIPTON
COMMENTS
LT1211/LT1212
Dual/Quad 14MHz, 7V/µs, Single Supply Precision Op Amps
Input Common Mode Includes Ground, 275µV VOS(MAX),
6µV/°C Max Drift, Max Supply Current 1.8mA per Op Amp
LT1213/LT1214
Dual/Quad 28MHz, 12V/µs, Single Supply Precision Op Amps
Input Common Mode Includes Ground, 275µV VOS(MAX),
6µV/°C Max Drift, Max Supply Current 3.5mA per Op Amp
LT1215/LT1216
Dual/Quad 23MHz, 50V/µs, Single Supply Precision Op Amps
Input Common Mode Includes Ground, 450µV VOS(MAX),
6µV/°C Max Drift, Max Supply Current 6.6mA per Op Amp
LT1498/LT1499
Dual/Quad 10MHz, 6V/µs Rail-to-Rail Input and Output
C-LoadTM Op Amps
High DC Accuracy, 475µV VOS(MAX), 4µV/°C Max Drift,
Max Supply Current 2.2mA per Amp
LT1630/LT1631
Dual/Quad 30MHz, 10V/µs Rail-to-Rail Input and Output Op Amps
High DC Accuracy, 525µV VOS(MAX), 70mA Output Current,
Max Supply Current 4.4mA per Amp
C-Load is a trademark of Linear Technology Corporation.
sn1632 16323fs
16
Linear Technology Corporation
LT/TP 0998 4K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 1998