ETC LTC1064-2CSW

LTC1064-2
Low Noise, High Frequency,
8th Order Butterworth Lowpass Filter
U
FEATURES
■
■
■
■
■
■
■
DESCRIPTIO
8th Order Filter in a 14-Pin Package
140kHz Maximum Corner Frequency
No External Components
50:1 and 100:1 Clock to Cutoff Frequency Ratio
80µVRMS Total Wideband Noise
0.03% THD or Better
Operates from ±2.37V to ±8V Power Supplies
U
APPLICATIO S
■
■
■
Antialiasing Filters
Smoothing Filters
Tracking High Frequency Lowpass Filters
The LTC®1064-2 is a monolithic 8th order lowpass
Butterworth filter, which provides a maximally flat passband. The attenuation slope is –48dB/octave and the
maximum attenuation is in excess of 80db. An external
TTL or CMOS clock programs the filter’s cutoff frequency.
The clock to cutoff frequency ratio is 100:1 (Pin 10 at
V –) or 50:1 (Pin 10 at V +). The maximum cutoff frequency
is 140kHz. No external components are needed.
The LTC1064-2 features low wideband noise and low
harmonic distortion even for input voltages up to 3VRMS.
In fact the LTC1064-2 overall performance competes with
equivalent multiple op amp RC active realizations. The
LTC1064-2 is available in a 14-pin DIP or 16-pin surface
mounted SW package. The LTC1064-2 is fabricated using
LTC’s enhanced analog CMOS Si-gate process.
The LTC1064-2 is pin compatible with the LTC1064-1.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
8th Order Clock Sweepable
Lowpass Butterworth Filter
1
Measured Frequency Response
0
14
OUT C
LTC1064-2
2
13
NC
VIN
8V
4
5
6
7
AGND
V+
AGND
NC
RIN A
V–
fCLK
50/100
VOUT
NC
12
11
–15
–30
–8V
CLOCK = 5MHz
10
VOUT/VIN (dB)
3
VS = ±7.5V
NC
–45
–60
9
–75
8
–90
–105
1064 TA01a
NOTE: THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1µF
CAPACITOR CLOSE TO THE PACKAGE. THE NC PINS 1, 6, 8,
AND 13 SHOULD BE PREFERABLY GROUNDED.
0
100
200 300 400 500
FREQUENCY (kHz)
600
700
1064-2 TA01b
10642fa
1
LTC1064-2
W W
U
W
ABSOLUTE
AXI U RATI GS
(Note 1)
Total Supply Voltage (V + to V –) ............................ 16.5V
Power Dissipation .............................................. 400mW
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
Operating Temperature Range
LTC1064-2M (OBSOLETE) ............... – 55°C to 125°C
LTC1064-2C ....................................... – 40°C to 85°C
U
W
U
PACKAGE/ORDER I FOR ATIO
TOP VIEW
ORDER PART
NUMBER
NC
1
14 OUT C
VIN
2
13 NC
AGND
3
12 V –
V+
4
11 fCLK
AGND
5
10 50/100
NC
6
9
VOUT
RIN A
7
8
NC
LTC1064-2CN
N PACKAGE
14-LEAD PDIP
TJMAX = 150°C, θJA = 110°C/W
J PACKAGE
14-LEAD CERDIP
LTC1064-2MJ
LTC1064-2CJ
OBSOLETE PACKAGE
ORDER PART
NUMBER
TOP VIEW
NC
1
16 OUT C
VIN
2
15 NC
AGND
3
14
V–
V+
4
13 NC
AGND
5
12 fCLK
NC
6
11 50/100
NC
7
10 NC
RIN A
8
9
LTC1064-2CSW
VOUT
SW PACKAGE
16-LEAD PLASTIC (WIDE) SO
TJMAX = 150°C, θJA = 130°C/W
Consider the N14 Package for Alternate Source
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±7.5V, 100:1, fCLK = 2MHz, R1 = 10k, TTL clock input level unless
otherwise specified.
PARAMETER
CONDITIONS
Passband Gain (Note 2)
Gain TempCo
–3dB Frequency
Referenced to 0dB, 1Hz to 1kHz
Gain at –3dB Frequency
Stopband Attenuation
Stopband Attenuation
Stopband Attenuation
Stopband Attenuation
100:1
50:1
Referenced to 0dB, fIN = 20kHz
At 1.5f –3dB , 50:1, fIN = 60kHz
At 2f –3dB , 100:1, fIN = 40kHz
At 3f –3dB , 100:1, fIN = 60kHz
At 4f –3dB , 100:1, fIN = 80kHz
Input Frequency Range
100:1
50:1
Output Voltage Swing and
Operating Input Voltage Range
VS = ±2.37V
VS = ±5V
VS = ±7.5V
Total Harmonic Distortion
VS = ±5V, Input = 1VRMS at 1kHz
VS = ±7.5V, Input = 3VRMS at 1kHz
Wideband Noise
VS = ±5V, Input = GND 1Hz – 1.99MHz
VS = ±7.5V, Input = GND 1Hz – 1.99MHz
MIN
●
●
●
●
TYP
–0.5
–24
–44
0.0002
20
40
–3
–27
–47
–74
–90
0
0
●
●
●
MAX
UNITS
0.15
–2.75
dB
dB/°C
kHz
kHz
dB
dB
dB
dB
dB
<fCLK/2
<fCLK
kHz
kHz
V
V
V
±1.1
±3.1
±5.0
0.015
0.03
80
90
%
%
µVRMS
µVRMS
10642fa
2
LTC1064-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±7.5V, 100:1, fCLK = 2MHz, R1 = 10k, TTL clock input level unless
otherwise specified.
PARAMETER
CONDITIONS
Output DC Offset (Note 2)
Output DC Offset TempCo
VS = ±7.5V
VS = ±5V
MIN
Input Impedance
10
Output Impedance
f OUT = 10kHz
Output Short-Circuit Current
Source/Sink
Clock Feedthrough
Maximum Clock Frequency
50% Duty Cycle, VS = ±5V
50% Duty Cycle, TA = 25°C, VS = ±7.5V
Power Supply Current
VS = ±2.37V, f CLK = 1MHz
VS = ±5V, f CLK = 1MHz
TYP
MAX
UNITS
±30
±90
±125
mV
µV/°C
20
kΩ
2
Ω
3/1
mA
200
µVRMS
11
14
●
●
VS = ±7.5V, f CLK = 1MHz
17
●
Power Supply Voltage Range
●
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
±2.37
5
7
MHz
MHz
22
23
26
28
32
mA
mA
mA
mA
mA
±8
V
Note 2: For tighter specifications please contact LTC Marketing.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Amplitude Response
Phase Response
–90
–30
PHASE (DEG)
VOUT/VIN (dB)
–45
fCLK = 2MHz
f–3dB = 40kHz
–45
fCLK = 5MHz
f–3dB = 100kHz
–60
–105
10k
–135
–180
–225
–270
–315
–75
–90
220
VS = ±7.5V
TA = 25°C
f CLK = 1MHz
100:1
f–3dB = 10kHz
0
VS = ±7.5V; 50:1
TA = 25°C
1M
1064 G01
VS = ±7.5V
200 T = 25°C
A
180 f CLK = 1MHz
100:1
160 f
–3dB = 10kHz
140
120
100
80
60
–360
40
–405
20
–450
100k
fIN (Hz)
GROUP DELAY (µs)
fCLK = 7MHz
f–3dB = 140kHz
0
–15
Group Delay vs Frequency
45
15
0
1
2
3
4
6 7
fIN (kHz)
5
8
9 10 11
1064 G02
0
0
1
2
3
4
5 6 7
fIN (kHz)
8
9 10 11
1064 G03
10642fa
3
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Phase vs f –3dB Frequency
Phase Matching
2.4
30
fCLK = 2MHz
f–3dB = 40kHz
PHASE (DEG)
PHASE MATCH (±DEG)
fCLK = 500kHz
f–3dB = 10kHz
–90
fCLK = 1MHz
f–3dB = 20kHz
–120
–150
–180
–210
1.6
1.2
0.8
0.4
–240 VS = ±7.5V
50:1
–270
100
0
1k
FREQUENCY (Hz)
10k
0
4
20
8
12
16
FREQUENCY (kHz)
1064 G04
800
fCLK = 2MHz
600 100:1, f–3dB = 20kHz
(530)
400
(335)
fCLK = 5MHz
200
100:1, f–3dB = 50kHz
0
0.1k
24
1k
10k
FREQUENCY (Hz)
100k
1064-2 G06
Harmonic Distortion vs Amplitude
1
fCLK = 1MHz, f–3dB = 20kHz, 50:1
HARMONIC DISTORTION (%)
HARMONIC DISTORTION (%)
fCLK = 500kHz
100:1, f–3dB = 5kHz
1200
(1060)
1000
1064-2 G05
Harmonic Distortion vs Frequency
0.1
1400
2.0
–30
–60
VS = ±7.5V, fCLK = 1MHz, f–3dB = 20kHz, 50:1
50 UNIT SAMPLE (TA = 25°C TO 125°C)
OUTPUT NOISE (nV/√Hz)
0
Noise Spectral Density
1600
±5V, 1VRMS INPUT
±7.5V, 3VRMS INPUT
0.01
±2.5V
±5V
0.1
±7V
0.01
fCLK = 1MHz, f–3dB = 20kHz
50:1, 1kHz INPUT
0.001
1k
10k
20k
0.001
0.5
FREQUENCY (Hz)
1.0
AMPLITUDE (VRMS)
1064-2 G08
1064-2 G07
Amplitude Response with Pin 10
at Ground
Power Suppy vs Current
48
15
44
PIN 10 AT GROUND
fCLK =1MHz
0
40
36
–15
32
28
24
TA = –55°C
20
TA = 25°C
16
TA = 125°C
VOUT/VIN (dB)
POWER SUPPLY CURRENT (mA)
5.0
–30
–45
–60
–75
12
8
–90
4
–105
0
0 2
4
6 8 10 12 14 16 18 20 22 24
POWER SUPPLY VOLTAGE (V)
1064 G09
1
10
fIN (kHz)
100
1064-2 G10
10642fa
4
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Table 1. Gain/Delay, f –3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 50kHz, Ratio = Pin 10 at V + (fltr 50:1)
FREQUENCY (kHz)
GAIN (dB)
Table 3. Gain/Delay, f –3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 100kHz, Ratio = Pin 10 at V – (fltr 100:1)
DELAY (ms)
FREQUENCY (kHz)
GAIN (dB)
DELAY (ms)
0.200
–0.247
0.857
0.200
–0.213
0.821
0.300
–0.270
0.872
0.300
–0.240
0.837
0.400
–0.290
0.893
0.400
–0.260
0.858
0.500
–0.300
0.929
0.500
–0.280
0.893
0.600
–0.320
0.983
0.600
–0.310
0.947
0.700
–0.370
1.071
0.700
–0.370
1.034
0.800
–0.520
1.210
0.800
–0.530
1.172
0.900
–1.200
1.364
0.900
–1.200
1.325
1.000
–3.380
1.381
1.000
–3.370
1.346
1.100
–7.530
1.192
1.100
–7.500
1.158
1.200
–12.670
0.935
1.200
–12.640
0.899
Table 2. Gain, f –3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 50kHz, Ratio = Pin 10 at V + (fltr 50:1)
FREQUENCY (kHz)
GAIN (dB)
Table 4. Gain, f–3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 100kHz, Ratio = Pin 10 at V – (fltr 100:1)
FREQUENCY (kHz)
GAIN (dB)
0.500
–0.298
0.500
–0.279
1.000
–3.380
1.000
–3.370
1.500
–27.500
1.500
–27.500
2.000
–47.200
2.000
–47.200
2.500
–63.300
2.500
–62.300
3.000
–75.190
3.000
–75.130
3.500
–86.100
3.500
–86.090
4.000
–95.310
4.000
–95.210
4.500
–104.240
4.500
–103.030
5.000
–109.650
5.000
–108.690
5.500
–121.930
5.500
–114.830
6.000
–123.920
6.000
–120.540
6.500
–114.150
6.500
–114.750
7.000
–116.990
7.000
–116.430
7.500
–120.070
7.500
–120.790
8.000
–113.470
8.000
–121.290
8.500
–130.090
8.500
–119.970
9.000
–114.770
9.000
–120.020
9.500
–117.760
9.500
–125.170
10642fa
5
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Table 5. Gain, f –3dB = 20kHz,
LTC1064-2 Typical Response VS = ±7.5V, TA = 25°C,
fCLK = 1MHz, Ratio = Pin 10 at V + (fltr 50:1)
Table 6. Gain, f–3dB = 140kHz,
LTC1064-2 Typical Response VS = ±7.5V, TA = 25°C,
fCLK = 7MHz, Ratio = Pin 10 at V+ (fltr 50:1)
FREQUENCY (kHz)
GAIN (dB)
FREQUENCY (kHz)
GAIN (dB)
10.000
–0.308
50.00
–0.238
20.000
–3.350
60.00
–0.140
30.000
–27.400
70.00
0.050
40.000
–47.100
80.00
0.350
50.000
–62.300
90.00
0.810
60.000
–74.890
100.00
1.450
70.000
–85.430
110.00
2.110
80.000
–95.070
120.00
1.830
90.000
–103.150
130.00
–0.700
100.000
–108.700
140.00
–4.840
110.000
–107.520
150.00
–9.350
120.000
–108.030
160.00
–13.690
130.000
–104.990
170.00
–17.760
140.000
–106.090
180.00
–21.600
150.000
–105.320
190.00
–25.200
200.00
–28.500
210.00
–31.800
220.00
–34.800
Table 7. Gain Non-Butterworth Response (Pin 10 to GND),
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 100kHz
230.00
–37.700
GAIN (dB)
240.00
–40.500
0.500
–0.012
250.00
–43.200
1.000
1.240
260.00
–45.700
1.500
–14.690
270.00
–48.200
2.000
–28.600
280.00
–50.500
2.500
–41.100
290.00
–52.700
3.000
–52.500
300.00
–54.900
3.500
–62.800
4.000
–71.500
4.500
–79.370
5.000
–86.730
5.500
–93.340
FREQUENCY (kHz)
6.000
–99.350
6.500
–105.270
7.000
–113.270
7.500
–114.600
8.000
–114.010
8.500
–122.810
9.000
–122.980
9.500
–119.450
10642fa
6
LTC1064-2
U
U
U
PI FU CTIO S
(Pin Numbers Refer to the 14-Pin Package)
NC (Pins 1, 6, 8 and 13): The “no connection” pins should
be preferably grounded. These pins are not internally
connected.
VIN, VOUT (Pins 2, 9): The input Pin 2 is connected to an
18k resistor tied to the inverting input of an op amp. Pin
2 is protected against static discharge. The device’s
output, Pin 9, is the output of an op amp which can
typically source/sink 3mA/1mA. Although the internal op
amps are unity gain stable, driving long coax cables is not
recommended.
When testing the device for noise and distortion, the
output, Pin 9, should be buffered. (Figure 1) The op amp
power supply wire (or trace) should be connected
directly to the power source. To eliminate switching
transients from filter output, buffer filter output with a
third order lowpass (Figure 5).
AGND (Pins 3, 5): For dual supply operation these pins
should be connected to a ground plane. For single supply
operation both pins should be tied to one half supply,
(Figure 3).
V +, V – (Pins 4, 12): Should be bypassed with a 0.1µF
capacitor to an adequate AGND. Low noise, nonswitching
power supplies are recommended. To avoid latchup when
the power supplies exhibit high turn-on transients, a
1N5817 Schottky diode should be added from the V + and
V – pins to ground (Figures 1, 2 and 3).
RIN A, OUT C (Pins 7, 14): A very short connection between
Pin 7 and Pin 14 is recommended. This connection should
be preferably done under the IC package. In a breadboard
use a one inch, or less, shielded coaxial cable: the shield
should be grounded. In a PC board, use a one inch trace or
less; surround the trace by a ground plane.
50/100 (Pin 10): The DC level at this pin determines the
ratio of clock frequency to the –3dB frequency of the filter.
The ratio is 50:1 when Pin 10 is at V + and 100:1 when
Pin 10 is at V –. This pin should be bypassed with a 0.1µF
capacitor to analog ground when it’s connected to V – or V +
(Figure 1). See Tables 1 through 7 for typical gain and delay
responses for the two ratios.
fCLK (Pin 11): For ±5V supplies the logic threshold level is
1.4V. For ±8V and 0V to 5V supplies the logic threshold
levels are 2.2V and 3V respectively. The logic threshold
levels vary ±100mV over the full military temperature
range. The recommended duty cycle of the input clock is
50% although for clock frequencies below 500kHz the
clock “on” time can be as low as 200ns. The maximum
clock frequency for ±5V supplies is 4MHz. For ±7V supplies and above, the maximum clock frequency is 7MHz.
Do not allow the clock levels to exceed the power supplies.
For single supply operation ≥6V use level shifting at Pin 11
with T2L levels (Figure 4).
10642fa
7
LTC1064-2
U
TYPICAL APPLICATIO S
1
2
3
4
0.1µF 5
6
NC
POWER SOURCE
V+
V–
OUT C 14
1
13
2
LTC1064-2
12
V–
AGND
3
NC
VIN
V+
AGND
fCLK
50/100
NC
7 RIN A
VOUT
NC
0.1µF
11
10
9
8
20k
0.1µF
1N5817
V+/V –
20k
4
V+
0.1µF
6
–
0.1µF
8
7
VOUT
LT1006
+
4
RECOMMENDED OP AMPS:
LT1022, LT318, LT1056
5
NC
OUT C
VIN
NC
14
13
LTC1064-2
12
V–
AGND
V+
AGND
NC
RIN A
fCLK
50/100
VOUT
NC
11
V–
1N5817
0.1µF
10
9
8
750Ω
1064-2 F02
1064-2 F01
Figure 2. Using Schottky Diodes to Protect the
IC from Transient Supply Reversal.
0.1µF
Figure 1. Buffering the Filter Output. The Buffer Op Amp
Should Not Share the LTC1064-2 Power Lines.
1
2
NC
OUT C
14
13
NC
LTC1064-2
3
12
V–
AGND
4
V+= 15V
0.1µF
5
5k
6
V+/2
0.1µF
5k
7
VIN
V+
AGND
NC
RIN A
fCLK
50/100
VOUT
NC
11
10
0V TO 10V
9
8
1064-2 F03
Figure 3. Single Supply Operation. If Fast Power Up or Down
Transients are Expected, Use a 1N5817 Schottky Diode Between
Pin 4 and Pin 5. For V+ = 5V, Derive the Mid-Supply Voltage
with a 7.5k Resistor and an LT1004 2.5V Reference.
10642fa
8
LTC1064-2
U
TYPICAL APPLICATIO S
1
2
3
4
V+
5
5k
6
0.1µF
7
5k
NC
OUT C
VIN
NC
14
13
V+
LTC1064-2
12
V–
AGND
V+
AGND
NC
RIN A
fCLK
50/100
VOUT
NC
2.2k
T 2L
LEVEL
11
10
RATIO
5k 1µF
9
8
1064-2 F04
Figure 4. Level Shifting the Input T2L Clock
for Single Supply Operation ≥6V.
1
2
V+
0.1µF
NC
OUT C
VIN
NC
14
3
LTC1064-2
12
V–
AGND
4
V+
5
6
7
AGND
NC
RIN A
fCLK
50/100
VOUT
NC
20k
13
V–
0.1µF
11
10 +
V /GND/V –
9
8
VOUT
100pF
15V
10k
10k
–
50Ω
LT1056
220pF
0.027µF
+
1064-2 F05
–15V
Figure 5. Adding an Output Buffer-Filter to Eliminate Any Clock
Feedthrough. Passband ±0.1dB to 50kHz, –3dB at 94kHz.
10642fa
9
LTC1064-2
U
PACKAGE DESCRIPTIO
J Package
14-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
.005
(0.127)
MIN
.785
(19.939)
MAX
14
13
12
11
10
9
8
.220 – .310
(5.588 – 7.874)
.025
(0.635)
RAD TYP
1
2
3
4
5
6
7
.300 BSC
(7.62 BSC)
.200
(5.080)
MAX
.015 – .060
(0.381 – 1.524)
.008 – .018
(0.203 – 0.457)
0° – 15°
.045 – .065
(1.143 – 1.651)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
.014 – .026
(0.360 – 0.660)
.100
(2.54)
BSC
.125
(3.175)
MIN
J14 0801
OBSOLETE PACKAGE
10642fa
10
LTC1064-2
U
PACKAGE DESCRIPTIO
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
.770*
(19.558)
MAX
14
13
12
11
10
9
8
1
2
3
4
5
6
7
.255 ± .015*
(6.477 ± 0.381)
.300 – .325
(7.620 – 8.255)
.045 – .065
(1.143 – 1.651)
.130 ± .005
(3.302 ± 0.127)
.020
(0.508)
MIN
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
+.035
.325 –.015
(
+0.889
8.255
–0.381
NOTE:
1. DIMENSIONS ARE
)
.120
(3.048)
MIN
.005
(0.125) .100
MIN (2.54)
BSC
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
.018 ± .003
(0.457 ± 0.076)
N14 1002
10642fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC1064-2
U
PACKAGE DESCRIPTIO
SW Package
16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 ±.005
.030 ±.005
TYP
.398 – .413
(10.109 – 10.490)
NOTE 4
16
N
15
14
13
12
11
10
9
N
.325 ±.005
.420
MIN
.394 – .419
(10.007 – 10.643)
NOTE 3
1
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
1
.005
(0.127)
RAD MIN
.009 – .013
(0.229 – 0.330)
.291 – .299
(7.391 – 7.595)
NOTE 4
.010 – .029 × 45°
(0.254 – 0.737)
2
3
4
5
6
.093 – .104
(2.362 – 2.642)
7
8
.037 – .045
(0.940 – 1.143)
0° – 8° TYP
.050
(1.270)
BSC
NOTE 3
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.004 – .012
(0.102 – 0.305)
.014 – .019
(0.356 – 0.482)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
S16 (WIDE) 0502
10642fa
12
Linear Technology Corporation
LW/TP 1202 1K REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 1990