LTC1264-7 Linear Phase, Group Delay Equalized, 8th Order Lowpass Filter U DESCRIPTIO FEATURES ■ ■ ■ ■ ■ ■ ■ Steeper Roll-Off Than Bessel Filters High Speed: fC ≤ 200kHz Phase Equalized Filter in a 14-Pin Package Phase and Group Delay Response Fully Tested Transient Response Exhibits 5% Overshoot and No Ringing 65dB THD or Better Throughout a 100kHz Passband No External Components Needed UO APPLICATI ■ ■ ■ S The LTC1264-7 is a clock-tunable monolithic 8th order lowpass filter with linear passband phase and flat group delay. The amplitude response approximates a maximally flat passband and exhibits steeper roll-off than an equivalent 8th order Bessel filter. For instance, at twice the cutoff frequency the filter attains 28dB attenuation (vs 12dB for Bessel), while at three times the cutoff frequency the filter attains 55dB attenuation (vs 30dB for Bessel). The cutoff frequency of the LTC1264-7 is tuned via an external TTL or CMOS clock. The clock-to-cutoff frequency ratio of the LTC1264-7 can be set to 25:1 (pin 10 to V +) or 50:1 (pin 10 to V –). Data Communication Filters Time Delay Networks Phase Matched Filters When the filter operates at clock-to-cutoff frequency ratio of 25:1, the input is double-sampled to lower the risk of aliasing. The LTC1264-7 is optimized for speed. Depending on the operating conditions, cutoff frequencies between 200kHz and 250kHz can be obtained. (Please refer to the Passband vs Clock Frequency graphs.) The LTC1264-7 is pin-compatible with the LTC1064-X series. UO TYPICAL APPLICATI 4-Level PAM Eye Diagram 200kHz Linear Phase Lowpass Filter 8V 14 2 13 3 12 4 LTC1264-7 11 5 10 6 9 7 8 –8V fCLK = 5MHz 8V VOUT 1V/DIV VIN 1 1264-7 TA01 NOTE: THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1µF CAPACITOR CLOSE TO THE PACKAGE AND ANY PRINTED CIRCUIT BOARD ASSEMBLY SHOULD MAINTAIN A DISTANCE OF AT LEAST 0.2 INCHES BETWEEN ANY OUTPUT OR INPUT PIN AND THE fCLK LINE. 500ns/DIV 1264-7 TA02 fCLK = 5MHz fC = 200kHz 1 LTC1264-7 W W W AXI U U ABSOLUTE RATI GS (Note 1) Total Supply Voltage (V + to V –) .......................... 16.5V Power Dissipation............................................. 400mW Burn-In Voltage ................................................... 16.5V Voltage at Any Input ..... (V – – 0.3V) ≤ VIN ≤ (V + + 0.3V) Storage Temperature Range ............... – 65°C to 150°C Operating Temperature Range LTC1264-7C ...................................... – 40°C to 85°C LTC1264-7M ................................... – 55°C to 125°C Lead Temperature (Soldering, 10 sec)................. 300°C U W U PACKAGE/ORDER I FOR ATIO TOP VIEW ORDER PART NUMBER NC 1 16 OUT (C) NC 1 14 OUT (C) VIN 2 13 NC VIN 2 15 NC GND 3 12 V – GND 3 14 V – V+ 4 11 fCLK NC 5 10 25/50 LP (A) 6 9 VOUT RIN (A) 7 8 NC J PACKAGE 14-LEAD CERAMIC DIP LTC1264-7CN LTC1264-7CJ LTC1264-7MJ V+ LTC1264-7CS 13 NC 4 NC 5 12 fCLK NC 6 11 25/50 10 NC LP (A) 7 VOUT 9 RIN (A) 8 N PACKAGE 14-LEAD PLASTIC DIP ORDER PART NUMBER TOP VIEW S PACKAGE 16-LEAD PLASTIC SOL TJMAX = 150°C, θJA = 65°C/W (J ) TJMAX = 110°C, θJA = 65°C/W (N ) TJMAX = 110°C, θJA = 85°C/W ELECTRICAL CHARACTERISTICS VS = ±7.5V, RL = 10k, TA = 25°C, fCUTOFF = 100kHz or 50kHz, fCLK = 2.5MHz, TTL or CMOS level (maximum clock rise or fall time ≤ 1µs) and all gain measurements are referenced to passband gain, unless otherwise specified. PARAMETER Passband Gain Gain at 0.50 fCUTOFF (Note 3) Gain at 0.75 fCUTOFF Gain at fCUTOFF Gain at 2.0 fCUTOFF Gain with fCLK = 20kHz Gain with fCLK = 400kHz, VS = ±2.375V Gain with fCLK = 4MHz Phase Factor (F ) Phase = 180° – F (f/fC) (Note 1) Phase Nonlinearity (Note 1) 2 CONDITIONS 0.1Hz ≤ f ≤ 0.25 fCUTOFF fTEST = 25kHz, (f CLK / fC) = 25:1 fTEST = 50kHz, (f CLK / fC) = 25:1 fTEST = 25kHz, (f CLK / fC) = 50:1 fTEST = 75kHz, (f CLK / fC) = 25:1 fTEST = 100kHz, (f CLK / fC) = 25:1 fTEST = 50kHz, (f CLK / fC) = 50:1 fTEST = 200kHz, (f CLK / fC) = 25:1 fTEST = 100kHz, (f CLK / fC) = 50:1 fTEST = 200Hz, (f CLK / fC) = 50:1 fTEST = 8kHz, (fCLK / fC) = 25:1 fTEST = 16kHz, (f CLK / fC) = 25:1 fTEST = 160kHz, VIN = 1VRMS (fCLK / fC) = 25:1, TA = 0°C to 70°C (fCLK / fC) = 25:1 (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF ● ● ● ● ● ● ● ● MIN TYP MAX UNITS – 0.50 – 0.50 – 0.65 – 1.5 – 3.7 – 4.5 – 34 – 34 – 0.7 – 0.2 – 3.5 – 0.10 0.50 0.20 0.30 0.1 –1.9 – 2.3 – 20 – 27 0.1 0.5 – 1.4 dB dB dB dB dB dB dB dB dB dB dB – 0.15 –1.0 – 3.0 – 3.0 – 28 – 30 – 0.3 0.15 – 2.70 0.00 ±1.0 3.0 ● 407 ± 2 388 ± 2 ● ● 392 374 423 414 ±1.0 ±1.0 ● ● ± 2.0 ± 2.0 dB dB Deg Deg Deg Deg % % % % LTC1264-7 ELECTRICAL CHARACTERISTICS VS = ±7.5V, RL = 10k, TA = 25°C, fCUTOFF = 100kHz or 50kHz, fCLK = 2.5MHz, TTL or CMOS level (maximum clock rise or fall time ≤ 1µs) and all gain measurements are referenced to passband gain, unless otherwise specified. PARAMETER Group Delay (td) td = (F / 360)(1/fC); (Note 2, 3) Group Delay Ripple (Note 2) Input Frequency Range (Table 9, 10) Maximum fCLK Clock Feedthrough Wideband Noise (1Hz ≤ f < fCLK) Input Impedance Output DC Voltage Swing (Note 4) Output DC Offset (fCLK = 1MHz) Output DC Offset TempCo Power Supply Current (fCLK = 1MHz) CONDITIONS (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1, f ≤ fCUTOFF (f CLK / fC) = 50:1, f ≤ fCUTOFF (f CLK / fC) = 25:1 (f CLK / fC) = 50:1 VS = Single 5V (GND = 2V) VS = ±5V VS = ±7.5V 25:1, ±7.5V, f = fCLK VS = Single 5V VS = ±5V VS = ±7.5V MIN TYP 11.3 21.6 10.9 20.8 ● ● 11.7 22.9 ±1.0 ±1.0 ±2.0 ±2.0 ● ● <fCLK <fCLK /2 2 3 5 120 140 ± 5% 160 ± 5% 175 ± 5% 50 ±1.0 ±2.3 ±3.8 ±100 ±100 ±200 ±200 11 30 VS = ±2.375V VS = ±5V VS = ±7.5V 25:1, VS = ±5V 50:1, VS = ±5V 25:1, VS = ±5V 50:1, VS = ±5V VS = ±2.375V MAX ±2.0 ±3.0 ● ● 75 ±220 ±220 22 22 23 26 28 32 ±8 ● VS = ±5V 14 ● VS = ±7.5V 17 ● ±2.375 Power Supply Range 180 fCLK = 2.5MHz (fCLK /fC) = 25:1 90 PHASE (DEG) The ● denotes specifications which apply over the full operating temperature range. Note 1: Input frequencies, f, are linearly phase shifted through the filter as long as f ≤ fC; fC = cutoff frequency. Figure 1 curve (A) shows the typical phase response of an LTC1264-7 operating at fCLK = 2.5MHz, fC = 100kHz. An endpoint straight line, curve (B), depicts the ideal linear phase response of the filter. It is described by: phase shift = 180° – F (f/fC); f ≤ fC. F is arbitrarily called the “phase factor” expressed in degrees. The phase factor together with the specified deviation from the ideal straight line allows the calculation of the phase at a given frequency. Note, the maximum phase nonlinearity, Figure 1, occurs at the vicinity of f = 0.25 fC and = 0.75 fC. Example: The phase shift at 70kHz of the LTC1264-7 shown in Figure 1 is: phase shift = 180° – 407° (70kHz/100kHz) ± nonlinearity =– 104.9° ± 1% or –104.9° ± 1.05°. Note 2: Group delay and group delay deviation are calculated from the measured phase factor and phase deviation specifications. Note 3: The filter cutoff frequency is abbreviated as fCUTOFF or fC. Note 4: The AC swing is typically 9VP-P, 5.6VP-P, 1.8VP-P with ± 7.5V, ±5V, ±2.5V supply respectively. For more information refer to the THD + Noise vs Input graphs. UNITS µs µs µs µs % % % % kHz kHz MHz MHz MHz µVRMS µVRMS µVRMS µVRMS kΩ V V V mV mV µV/°C µV/°C mA mA mA mA mA mA V 0 B –90 A –180 –270 –360 0 10 20 30 40 50 60 70 80 90 100 FREQUENCY (kHz) LTC1264-7 F01 Figure 1. Phase Response in the Passband (Note 1) 3 LTC1264-7 U W TYPICAL PERFOR A CE CHARACTERISTICS 10 –10 VS = ±7.5V (fCLK /fC) = 25:1 450 –20 70°C –40 50:1 –50 25:1 –60 25°C 430 420 0°C 410 –70 –80 400 10 100 FREQUENCY (kHz) 1000 410 0°C 400 380 370 390 1 25°C 420 390 –90 –100 70°C 430 PHASE FACTOR –30 VS = ±7.5V (fCLK /fC) = 50:1 440 440 PHASE FACTOR GAIN (dB) 450 460 VS = ±7.5V fCLK = 1MHz TA = 25°C 0 Phase Factor vs fCLK (Typical Unit) Phase Factor vs fCLK (Typical Unit) Gain vs Frequency 0 3 2 fCLK (MHz) 1 5 4 1264-7 G01 0 3 2 fCLK (MHz) 1 1264-7 G02 Phase Factor vs fCLK (Min and Max Representative Units) 425 VS = ±7.5V (fCLK /fC) = 25:1 TA = 25°C 445 440 VS = ±5V (fCLK /fC) = 25:1 TA = 25°C 420 PHASE FACTOR PHASE FACTOR 435 430 425 420 415 415 410 405 410 405 400 400 395 395 0 1 3 2 fCLK (MHz) 4 5 0 0.5 1.0 1.5 2.0 fCLK (MHz) 2.5 3 180 2 135 2 135 1 90 1 90 0 45 0 45 0 –45 –2 –3 –90 PHASE –135 VS = ±7.5V fCLK = 2.5MHz fC = 100kHz (fCLK /fC) = 25:1 –3 –5 –6 –270 –7 10 20 30 40 50 60 70 80 90 100 110 FREQUENCY (kHz) –7 1264-7 G06 –90 PHASE –135 –4 –180 –6 0 –45 –2 –225 –5 GAIN –1 VS = ±7.5V fCLK = 2.5MHz fC = 50kHz (fCLK /fC) = 50:1 5 –180 –225 –270 10 15 20 25 30 35 40 45 50 55 FREQUENCY (kHz) 1264-7 G07 PHASE (DEG) GAIN –1 GAIN (dB) 180 PHASE (DEG) GAIN (dB) Passband Gain and Phase 3 –4 4 3.0 1264-7 G05 1264-7 G04 Passband Gain and Phase 5 1264-7 G03 Phase Factor vs fCLK (Min and Max Representative Units) 450 4 LTC1264-7 U W TYPICAL PERFOR A CE CHARACTERISTICS Passband Gain vs fCLK Passband Gain vs fCLK 5 3 A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz E. fCLK = 5MHz VS = ±7.5V (fCLK /fC) = 50:1 TA = 25°C 4 3 A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz E. fCLK = 5MHz 2 1 GAIN (dB) GAIN (dB) 2 5 0 –1 –2 –3 C D E 0 –1 –5 –5 100 FREQUENCY (kHz) 1000 B C D E 100 FREQUENCY (kHz) 1000 10 A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz Gain vs Frequency 10 0 –10 2 –20 –20 1 –30 –30 GAIN (dB) –1 GAIN (dB) 0 –10 –40 –50 –60 –2 B A C –3 –70 –4 –80 10 100 FREQUENCY (kHz) VS = ±7.5V fCLK = 5MHz (fCLK /fC) = 25:1 TA = 25°C 5 0 4 –10 3 B C –80 GAIN (dB) 1 0 –1 B C FREQUENCY (kHz) –5 B –1 A. TA = 70°C B. TA = –40°C –2 VS = SINGLE 5V fCLK = 2MHz (fCLK /fC) = 25:1 AGND = 2V –4 –5 100 10 200 FREQUENCY (kHz) 1264-7 G14 A 0 D –4 200 1 –3 A –3 100 10 2 –2 VS = SINGLE 5V (fCLK /fC) = 25:1 AGND = 2V TA = 25°C –70 –90 A. fCLK = 0.5MHz B. fCLK = 1MHz C. fCLK = 2MHz 1000 Maximum Passband vs Temperature A. fCLK = 0.5MHz B. fCLK = 1.0MHz C. fCLK = 1.5MHz D. fCLK = 2.0MHz VS = SINGLE 5V (fCLK /fC) = 25:1 AGND = 2V TA = 25°C 2 –30 100 FREQUENCY (kHz) 1264-7 G13 GAIN (dB) A –60 10 Passband Gain vs fCLK 10 –50 –90 1000 1264-7 G12 Gain vs fCLK –40 VS = ±5V fCLK = 3MHz (fCLK /fC) = 25:1 TA = 25°C –80 1264-7 G11 –20 –50 –70 100 FREQUENCY (kHz) 10 1000 –40 –60 –90 –5 1000 1264-7 G10 Gain vs Frequency 0 100 FREQUENCY (kHz) 1264-7 G09 10 3 B –5 Passband Gain vs fCLK at 85°C 4 A –4 10 5 GAIN (dB) 0 –1 –3 1264-7 G08 VS = ±5V (fCLK /fC) = 25:1 1 –2 A –3 –4 10 GAIN (dB) 2 1 –4 A. fCLK = 4MHz B. fCLK = 5MHz 3 –2 B A VS = ±7.5V (fCLK /fC) = 25:1 4 GAIN (dB) VS = ±7.5V (fCLK /fC) = 25:1 TA = 25°C 4 Passband Gain vs fCLK at 85°C 5 1264-7 G15 1 10 FREQUENCY (kHz) 100 1264-7 G16 5 LTC1264-7 U W TYPICAL PERFOR A CE CHARACTERISTICS Gain vs fCLK 10 –10 3 2 C GAIN (dB) B –40 –50 –60 –70 –80 –90 10 VS = SINGLE 5V (fCLK /fC) = 50:1 AGND = 2V TA = 25°C 0 –1 B A C D 5 10 –4.0 100 1 VS = ±7.5V (fCLK /fC) = 25:1 TA = 25°C –40 –50 –55 30 B 20 C D D 5 10 0 0 VS = ±5V VIN = 1VRMS fCLK = 1MHz (fCLK /fC) = 25:1 (5 REPRESENTATIVE UNITS) –45 40 C 10 VS = ±7.5V (fCLK /fC) = 50:1 TA = 25°C A 50 A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz THD (dB) B 50 THD vs Frequency Delay vs fCLK A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz 10 FREQUENCY (kHz) 1264-7 G19 60 DELAY (µs) DELAY (µs) –3.5 1264-7 G18 Delay vs fCLK 15 VS = SINGLE 5V fCLK = 2MHz (fCLK /fC) = 50:1 AGND = 2V FREQUENCY (kHz) 30 20 A. TA = 70°C B. TA = –40°C –2.0 –2.5 1264-7 G17 A –1.0 –1.5 –3.0 FREQUENCY (kHz) 25 B –3 –5 200 A 0 –2 –4 100 0.5 – 0.5 1 GAIN (dB) A A. fCLK = 0.5MHz B. fCLK = 1.0MHz C. fCLK = 1.5MHz D. fCLK = 2.0MHz VS = SINGLE 5V (fCLK /fC) = 50:1 AGND = 2V TA = 25°C 4 –20 GAIN (dB) 1.0 5 A. fCLK = 0.5MHz B. fCLK = 1MHz C. fCLK = 2MHz 0 –30 Maximum Passband vs Temperature Passband Gain vs fCLK –60 –65 –70 –75 –80 –85 20 40 60 80 100 120 140 160 180 200 220 INPUT FREQUENCY (kHz) –90 10 20 30 1264-7 G20 THD vs Frequency THD vs Frequency THD + Noise vs Input –40 –55 –50 –55 THD (dB) –60 VS = SINGLE 5V VIN = 0.5VRMS fCLK = 500kHz (fCLK /fC) = 25:1 AGND = 2V (5 REPRESENTATIVE UNITS) –45 –65 –70 –60 –45 –50 THD + NOISE (dB) VS = ±7.5V VIN = 1VRMS fCLK = 2.5MHz (fCLK /fC) = 25:1 (5 REPRESENTATIVE UNITS) –50 –65 –70 –80 –85 –85 –90 –90 –90 0.1 6 B –70 –85 –75 –80 1 10 20 FREQUENCY (kHz) 1264-7 G23 A –65 –80 100 A. VS = ±5V B. VS = ±7.5V –60 –75 10 FREQUENCY (kHz) fIN = 1kHz fCLK = 1MHz (fCLK /fC) = 25:1 –55 –75 1 50 1264-7 G22 –40 –45 10 FREQUENCY (kHz) 1264-7 G21 –40 THD (dB) 1 40 50 60 70 80 90 100 110 INPUT FREQUENCY (kHz) 1264-7 G24 1 INPUT AMPLITUDE (VRMS) 5 1264-7 G25 LTC1264-7 U W TYPICAL PERFOR A CE CHARACTERISTICS THD + Noise vs Input –40 A A. PIN 3 AT 2.5V B. PIN 3 AT 2V PHASE DIFFERENCE (DEG) THD + NOISE (dB) –50 –55 –60 –65 –70 –75 –80 –85 VS = SINGLE 5V fCLK = 500kHz fIN = 1kHz –90 50m 48 5 B PHASE DIFFERENCE BETWEEN ANY TWO UNITS (SAMPLE OF 50 REPRESENTATIVE UNITS) VS ≥ ±5V fCLK ≤ 2.5MHz (fCLK /fC) = 25:1 OR 50:1 TA = 0°C TO 70°C 4 3 2 1 fCLK = 1MHz 40 36 32 28 24 –55°C 25°C 125°C 20 16 12 8 4 0.1 INPUT AMPLITUDE (VRMS) 1 0 0 0 0.2 0.6 0.8 0.4 FREQUENCY (fCUTOFF/FREQUENCY) 1264-7 G26 GAIN (dB) 1.0 0 2 4 6 8 10 12 14 16 18 20 22 24 TOTAL POWER SUPPLY VOLTAGE (V) 1264-7 G28 1264-7 G27 Table 1. Passband Gain and Phase VS = ±7.5V, (fCLK / fC) = 25:1, TA = 25°C FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 44 POWER SUPPLY CURRENT (mA) –45 Power Supply Current vs Power Supply Voltage Phase Matching vs Frequency Table 2. Passband Gain and Phase VS = ±7.5V, (fCLK / fC) = 50:1, TA = 25°C PHASE (DEG) 0.064 0.064 0.058 – 0.639 – 2.741 180.00 81.14 –19.18 –120.63 – 221.78 FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 2MHz (Typical Unit) 0.000 20.000 40.000 60.000 80.000 – 0.006 – 0.006 – 0.164 – 0.958 – 3.003 180.00 79.42 – 22.13 –124.09 – 225.01 fCLK = 3MHz (Typical Unit) 0.000 30.000 60.000 90.000 120.000 – 0.067 – 0.067 – 0.287 – 0.944 – 2.545 fCLK = 4MHz (Typical Unit) 0.000 40.000 80.000 120.000 160.000 fCLK = 5MHz (Typical Unit) 0.000 50.000 100.000 150.000 200.000 GAIN (dB) PHASE (DEG) – 0.048 – 0.048 – 0.351 – 1.253 – 3.348 180.00 84.51 – 10.87 – 105.53 – 199.61 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 – 0.008 – 0.008 – 0.237 – 1.105 – 3.238 180.00 83.39 – 13.09 – 108.91 – 204.09 180.00 77.49 – 25.54 – 128.51 – 230.19 fCLK = 3MHz (Typical Unit) 0.000 15.000 30.000 45.000 60.000 0.044 0.044 – 0.065 – 0.863 – 3.022 180.00 81.04 – 18.64 – 118.48 – 217.67 – 0.031 – 0.031 – 0.078 – 0.332 – 1.275 180.00 75.23 – 30.06 – 135.27 – 239.76 fCLK = 4MHz (Typical Unit) 0.000 20.000 40.000 60.000 80.000 0.071 0.071 0.039 – 0.664 – 2.755 180.00 78.04 – 25.06 – 128.54 – 231.42 0.073 0.073 0.365 0.686 0.521 180.00 71.77 – 37.11 – 146.19 – 255.85 fCLK = 5MHz (Typical Unit) 0.000 25.000 50.000 75.000 100.000 0.089 0.089 0.141 – 1.437 – 2.421 180.00 74.36 – 32.41 – 139.33 – 246.01 7 LTC1264-7 U W TYPICAL PERFOR A CE CHARACTERISTICS Table 3. Passband Gain and Phase VS = ±5V, (fCLK / fC) = 25:1, TA = 25°C FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 GAIN (dB) Table 4. Passband Gain and Phase VS = ±5V, (fCLK / fC) = 50:1, TA = 25°C PHASE (DEG) 0.081 0.081 0.071 – 0.631 – 2.732 180.00 80.94 – 19.54 – 121.10 – 222.28 FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 2MHz (Typical Unit) 0.000 20.000 40.000 60.000 80.000 – 0.016 – 0.016 – 0.211 – 0.968 – 2.864 180.00 78.78 – 23.21 – 125.42 – 226.47 fCLK = 3MHz (Typical Unit) 0.000 30.000 60.000 90.000 120.000 – 0.006 – 0.006 – 0.044 – 0.369 – 1.507 180.00 76.07 – 28.54 – 133.27 – 237.35 fCLK = 1MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 0.032 0.032 – 0.249 – 1.135 – 3.225 180.00 84.60 – 10.65 – 105.20 – 199.22 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 0.101 0.101 – 0.043 – 0.864 – 3.021 180.00 82.47 – 15.45 – 113.28 – 210.54 fCLK = 3MHz (Typical Unit) 0.000 15.000 30.000 45.000 60.000 0.125 0.125 0.043 – 0.753 – 2.987 180.00 77.88 – 25.31 – 128.74 – 231.29 0.161 0.161 0.166 – 0.515 – 2.598 180.00 81.47 – 18.52 – 119.79 – 220.82 FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 0.125 0.125 0.043 – 0.706 – 2.781 180.00 80.23 – 20.75 – 122.53 – 223.59 GAIN (dB) PHASE (DEG) GAIN (dB) PHASE (DEG) 0.075 0.075 – 0.217 – 1.108 – 3.198 180.00 84.79 – 10.40 – 105.10 – 199.26 fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 0.114 0.114 – 0.122 – 0.988 – 3.111 180.00 83.96 – 11.88 – 107.02 – 201.63 0.174 0.174 0.066 – 0.744 – 2.949 180.00 81.36 – 17.84 – 117.12 – 215.79 0.232 0.232 0.219 – 0.599 – 3.031 180.00 75.98 – 29.26 – 134.63 – 239.09 fCLK = 1.5MHz (Typical Unit) 0.000 15.000 30.000 45.000 60.000 0.061 0.061 – 0.096 – 0.741 – 2.432 180.00 78.49 – 23.82 – 126.47 – 228.12 fCLK = 1.5MHz (Typical Unit) 0.000 7.500 15.000 22.500 30.000 fCLK = 2MHz (Typical Unit) 0.000 20.000 40.000 60.000 80.000 0.151 0.151 0.321 0.203 – 0.838 180.00 75.03 – 31.15 – 137.86 – 244.58 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 8 PHASE (DEG) Table 6. Passband Gain and Phase VS = Single 5V, (fCLK /fC) = 50:1, TA = 25°C Table 5. Passband Gain and Phase VS = Single 5V, (fCLK /fC) = 25:1, TA = 25°C FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 GAIN (dB) LTC1264-7 U U U PI FU CTIO S Power Supply Pins (4, 12) The V + (pin 4) and the V – (pin 12) should each be bypassed with a 0.1µF capacitor to an adequate analog ground. The filter’s power supplies should be isolated from other digital or high voltage analog supplies. A low noise linear supply is recommended. Using a switching power supply will lower the signal-to-noise ratio of the filter. The supply during power-up should have a slew rate less than 1V/µs. When V + is applied before V – and V – is allowed to go above ground, a signal diode should clamp V – to prevent latch-up. Figures 2 and 3 show typical connections for dual and single supply operation. Clock Input Pin (11) Any TTL or CMOS clock source with a square-wave output and 50% duty cycle (±10%) is an adequate clock source for the device. The power supply for the clock source should not be the filter’s power supply. The analog ground for the filter should be connected to clock’s ground at a single point only. Table 7 shows the clock’s low and high level threshold values for a dual or single supply operation. A pulse generator can be used as a clock source provided the high level ON time is greater than 0.1µs. Sine waves are not recommended for clock input frequencies less than 100kHz, since excessively slow clock rise or fall times generate internal clock jitter (maximum clock rise or fall time ≤ 1µs). The clock signal should be routed from the right side of the IC package and perpendicular to it to avoid coupling to any input or output analog signal path. A 200Ω resistor between clock source and pin 11 will slow down the rise and fall times of the clock to further reduce charge coupling (Figures 2 and 3). age is recommended. The analog ground plane should be connected to any digital ground at a single point. For dual supply operation, pin 3 should be connected to the analog ground plane. For single supply operation pin 3 should be biased at 1/2 supply and should be bypassed to the analog ground plane with at least a 1µF capacitor (Figure 3). For single 5V operation at the highest fCLK of 2MHz, pin 3 should be biased at 2V. This minimizes passband gain and phase variations. Ratio Input Pin (10) The DC level at this pin determines the ratio of the clock frequency to the cutoff frequency of the filter. Pin 10 at V + gives a 25:1 ratio and pin 10 at V – gives a 50:1 ratio. For single supply operation the ratio is 25:1 when pin 10 is at V + and 50:1 when pin 10 is at ground. When pin 10 is not tied to ground, it should be bypassed to analog ground with a 0.1µF capacitor. If the DC level at pin 10 is switched mechanically or electrically at slew rates greater than 1V/µs while the device is operating, a 10k resistor should be connected between pin 10 and the DC source. V– VIN 1 14 2 13 3 12 4 V+ 0.1µF HIGH LEVEL ≥ 2.18V ≥ 1.45V ≥ 0.73V ≥ 7.80V ≥ 1.45V LOW LEVEL ≤ 0.5V ≤ 0.5V ≤ – 2.0V ≤ 6.5V ≤ 0.5V Analog Ground Pins (3, 5) The filter performance depends on the quality of the analog signal ground. For either dual or single supply operation, an analog ground plane surrounding the pack- 200Ω 11 5 10 6 9 7 8 CLOCK SOURCE V+ + GND DIGITAL SUPPLY VOUT 1264-7 F02 Figure 2. Dual Supply Operation for an fCLK/fCUTOFF = 25:1 Table 7. Clock Source High and Low Threshold Levels POWER SUPPLY Dual Supply = ±7.5V Dual Supply = ±5V Dual Supply = ± 2.5V Single Supply = 12V Single Supply = 5V LTC1264-7 0.1µF VIN 14 2 13 3 12 11 200Ω 5 10 V+ 6 9 7 8 4 V+ 0.1µF 10k 10k 1 LTC1264-7 CLOCK SOURCE + GND DIGITAL SUPPLY + 1µF VOUT 1264-7 F03 Figure 3. Single Supply Operation for an fCLK/fCUTOFF = 25:1 9 LTC1264-7 U U U PI FU CTIO S Filter Input Pin (2) The input pin is connected internally through a 50k resistor tied to the inverting input of an op amp. Filter Output Pins (9, 6) Pin 9 is the specified output of the filter; it can typically source 3mA and sink 1mA. Driving coaxial cables or resistive loads less than 20k will degrade the total harmonic distortion of the filter. When evaluating the device’s – 1k + LT1220 U W U UO S I FOR ATIO Clock Feedthrough Clock feedthrough is defined as the RMS value of the clock frequency and its harmonics that are present at the filter’s output pin (9). The clock feedthrough is tested with the input pin (2) grounded and it depends on PC board layout and on the value of the power supplies. With proper layout techniques the values of the clock feedthrough are shown in Table 8. Table 8. Clock Feedthrough 25:1 100µVRMS 100µVRMS 120µVRMS 50:1 100µVRMS 400µVRMS 1000µVRMS Note: The clock feedthrough at 25:1 is imbedded in the wideband noise of the filter. Clock waveform is a square wave. Any parasitic switching transients during the rise and fall edges of the incoming clock are not part of the clock feedthrough specifications. Switching transients have frequency contents much higher than the applied clock; their amplitude strongly depends on scope probing techniques as well as grounding and power supply bypassing. The 10 Pins 7 and 14 should be connected together. In a printed circuit board the connection should be done under the IC package through a short trace surrounded by the analog ground plane. Pins 1, 5, 8 and 13 are not connected to any internal circuit point on the device and should be preferably tied to analog ground. Figure 4. Buffer for Filter Output VS Single 5V ±5V ±7.5V External Connection Pins (7, 14) NC Pin (1, 5, 8, 13) 1264-7 F04 APPLICATI distortion an output buffer is required. A noninverting buffer, Figure 4, can be used provided that its input common-mode range is well within the filter’s output swing. Pin 6 is an intermediate filter output providing an unspecified 6th order lowpass filter. Pin 6 should not be loaded. clock feedthrough, if bothersome, can be greatly reduced by adding a simple R/C lowpass network at the output of the filter pin (9). This R/C will completely eliminate any switching transients. Wideband Noise The wideband noise of the filter is the total RMS value of the device’s noise spectral density and it is used to determine the operating signal-to-noise ratio. Most of its frequency contents lie within the filter passband and it cannot be reduced with post filtering. For instance, the LTC1264-7 wideband noise at ±5V supply is 160µVRMS, 145µVRMS of which have frequency contents from DC up to the filter’s cutoff frequency. The total wideband noise (µVRMS) is nearly independent of the value of the clock. The clock feedthrough specifications are not part of the wideband noise. Speed Limitations To avoid op amp slew rate limiting at maximum clock frequencies, the signal amplitude should be kept below a specified level as shown in Table 9. LTC1264-7 U W U UO APPLICATI S I FOR ATIO Table 9. Maximum VIN vs VS and Clock POWER SUPPLY ±7.5V ±5V Single 5V Aliasing MAXIMUM fCLK 5.0MHz 4.5MHz 4.0MHz ≥ 3.5MHz 3.0MHz ≥ 3.0MHz 2.0MHz MAXIMUM VIN 1.6VRMS (fIN ≥ 160kHz) 2.0VRMS (fIN ≥ 160kHz) 2.5VRMS (fIN ≥ 160kHz) 1.6VRMS (fIN ≥ 500kHz) 1.6VRMS (fIN ≥ 100kHz) 0.7VRMS (fIN ≥ 500kHz) 0.5VRMS (fIN ≥ 400kHz) Transient Response Aliasing is an inherent phenomenon of sampled data systems and it occurs when input frequencies close to the sampling frequency are applied. For the LTC1264-7 case at 50:1, an input signal whose frequency is in the range of fCLK ±10%, will be aliased back into the filter’s passband. If, for instance, an LTC1264-7 operating with a 100kHz clock and 2kHz cutoff frequency receives a 95kHz 10mV input signal, a 5kHz 56µVRMS alias signal will appear at its output. When the LTC1264-7 operates with a clock-tocutoff frequency of 25:1, aliasing occurs at twice the clock frequency. Table 10 shows details. 2V/DIV Table 10. Aliasing (fCLK = 100kHz ) 10µs/DIV INPUT = 10kHz ± 3V fCLK = 2.5MHz RATIO = 25:1 Figure 5. ts INPUT FREQUENCY (VIN = 1VRMS, fIN = fCLK ± fOUT) (kHz) 25:1, fCUTOFF = 4kHz OUTPUT LEVEL (Relative to Input, 0dB = 1VRMS) (dB) OUTPUT FREQUENCY (Aliased Frequency fOUT = ABS [fCLK ± fIN]) (kHz) 175 (or 225) 180 (or 220) 185 (or 215) 190 (or 210) 195 (or 205) 50:1, fCUTOFF = 2kHz –76 – 69 – 62 – 43 –7 25 20 15 10 5 75 (or 125) 80 (or 120) 85 (or 115) 90 (or 110) 95 (or 105) 99 (or 101) –96 – 90 – 82 – 72 – 45 0 25 20 15 10 5 1 OUTPUT INPUT 90% 50% 10% Table 11. Transient Response of LTC Lowpass Filters td tr 0.36 ±5% fCUTOFF 2 SETTLING TIME (ts) = ±5% f (TO 1% of OUTPUT) CUTOFF RISE TIME (tr) = 1.15 TIME DELAY (td) = GROUP DELAY ≈ fCUTOFF (TO 50% OF OUTPUT) 1164-7 F06 LOWPASS FILTER LTC1064-3 Bessel LTC1164-5 Bessel LTC1164-6 Bessel DELAY TIME* (SEC) 0.50/fC 0.43/fC 0.43/fC RISE SETTLING OVERTIME** TIME*** SHOOT (SEC) (SEC) (%) 0.34/fC 0.80/fC 0.5 0.34/fC 0.85/fC 0 0.34/fC 1.15/fC 1 LTC1264-7 Linear Phase LTC1164-7 Linear Phase LTC1064-7 Linear Phase 1.15/fC 1.20/fC 1.20/fC 0.36/fC 0.39/fC 0.39/fC 2.05/fC 2.20/fC 2.20/fC 5 5 5 LTC1164-5 Butterworth 0.80/fC 0.48/fC 2.40/fC 11 LTC1164-6 Elliptic LTC1064-4 Elliptic LTC1064-1 Elliptic 0.85/fC 0.90/fC 0.85/fC 0.54/fC 0.54/fC 0.54/fC 4.30/fC 4.50/fC 6.50/fC 18 20 20 * To 50% ±5%, ** 10% to 90% ±5%, *** To 1% ±0.5% Figure 6. Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC1264-7 U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. J Package 14-Lead Ceramic DIP 0.200 (5.080) MAX 0.290 – 0.320 (7.366 – 8.128) 0.785 (19.939) MAX 0.005 (0.127) MIN 14 12 13 11 10 9 8 0.015 – 0.060 (0.381 – 1.524) 0.008 – 0.018 (0.203 – 0.460) 0.220 – 0.310 (5.588 – 7.874) 0.025 (0.635) RAD TYP 0° – 15° 1 0.385 ± 0.025 (9.779 ± 0.635) 0.038 – 0.068 (0.965 – 1.727) 0.100 ± 0.010 (2.540 ± 0.254) 0.014 – 0.026 (0.360 – 0.660) 2 3 4 5 6 7 0.098 (2.489) MAX 0.125 (3.175) MIN J14 0392 N Package 14-Lead Plastic DIP 0.300 – 0.325 (7.620 – 8.255) 0.045 – 0.065 (1.143 – 1.651) 0.015 (0.380) MIN 0.130 ± 0.005 (3.302 ± 0.127) ( +0.635 8.255 –0.381 ) 14 13 12 11 10 9 8 1 2 3 4 5 6 7 0.260 ± 0.010 (6.604 ± 0.254) 0.009 – 0.015 (0.229 – 0.381) +0.025 0.325 –0.015 0.770 (19.558) MAX 0.065 (1.651) TYP 0.075 ± 0.015 (1.905 ± 0.381) 0.018 ± 0.003 (0.457 ± 0.076) 0.100 ± 0.010 (2.540 ± 0.254) 0.125 (3.175) MIN S Package 16-Lead Plastic SOL 0.398 – 0.413 (10.109 – 10.490) 0.291 – 0.299 (7.391 – 7.595) 0.005 (0.127) RAD MIN 0.010 – 0.029 × 45° (0.254 – 0.737) 16 0.093 – 0.104 (2.362 – 2.642) 15 14 13 12 11 10 9 0.037 – 0.045 (0.940 – 1.143) 0° – 8° TYP 0.394 – 0.419 (10.007 – 10.643) SEE NOTE 0.009 – 0.013 (0.229 – 0.330) SEE NOTE 0.016 – 0.050 (0.406 – 1.270) 0.050 (1.270) TYP 0.004 – 0.012 (0.102 – 0.305) 0.014 – 0.019 (0.356 – 0.482) TYP NOTE: PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS. 1 2 3 4 5 6 7 8 SOL16 0392 12 Linear Technology Corporation LT/GP 1292 10K REV 0 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977 LINEAR TECHNOLOGY CORPORATION 1992