Miniature Power Relay IF - Faston V23077 PCB/plug-in relay for DC voltage, neutral, monostable Features ● High-temperature relay with contact-side Faston terminals ● Switching capacity 4000 VA at 125 °C ambient temperature ● Nominal coil power 360 mW ● Mechanical and electrical characteristics comply with the “Rules for electrical relays in power installations” (VDE 0435/9.72) ● Clearance/creepage distances > 8 mm between coil and contact ● Tracking resistance of the plastics to PTI 250 ● Used for safe electrical insulation in the following applications – open and closed-loop control equipment for domestic use (VDE 0631) – electrical equipment for domestic use (EN 60 335-1/VDE 0700) Typical applications ● Oven timers ● Electric heaters ● Microwave ovens ● Air-conditioning equipment ● Power supply equipment ECR3029-2 Approx. original size Design – With 1 make contact or with 1 break contact (changeover contact on request) – For printed circuit assembling – With PCB terminals (coil) and flat terminals (contacts) for 6.35 mm fast-on connectors – Dust-protected Approvals VDE BEAB 2 VDE Mark of conformity SEV 91.1 11672.01 CSA LR 89731-12 UL File E 48393 SEMKO 9330076 ÖVE 22905/E BEAB C 0573 5081 Siemens AG Miniature Power Relay IF - Faston Dimensional drawing (in mm) Fast-on connectors Mounting hole layout View on the terminals Note The dust-protected version must be checked to ensure that the clearances and creepage distances required by VDE are not compromised by conductor paths running between the relay and the board. 2.5 mm basic grid to EN 60097 and DIN 40803, fine Terminal assignment View on the terminals 1 make contact Siemens AG 1 break contact 3 Miniature Power Relay IF - Faston Contact data Contact category III according to VDE 0435 Part 120/10.81, Appendix B Ordering code, block 3 Number of contacts and type A402 A403 1 make contact Contact assembly 1 break contact Single contacts Contact material AgCdO (AgSnO2 on request) Max. continuous current at max. ambient temperature 16 A 16 A Inrush current (max. 4 s for 10% duty cycle) 25 A 25 A Maximum switching voltage Maximum switching capacity AC voltage DC voltage Recommended for loads greater than Contact resistance (initial value)/ measuring current/driver voltage 440 V~ 300 V– 4000 VA See load limit curve 500 mA, 12 V~ ≤ 100 mΩ/1 A/24 V Note: Inrush currents up to 150 A available on request. Load limit curve I = switching current U = switching voltage = recommended application field Load limit curve: Safe switch-off, no stationary arc > 10 ms 4 Siemens AG Miniature Power Relay IF - Faston Coil data Nominal voltages From 3 V– to 110 V– Nominal power consumption, typ., at 20 °C 360 mW Pull-in power, typ., at 20 °C 140 mW Operating range/pickup class according to IEC 255-1-00 and VDE 0435 Part 201 Minimum release voltage 2/b 10 % of nominal voltage Coil versions Nominal voltage Unom V– Operate voltage at 20 °C Uop cold V– 3 Operating voltage range at 20 °C Min. voltage UI V– 1.9 Max. voltage UII V– Resistance at 20 °C Coil number Ordering code block 2 Ω 2.1 8.5 25 ± 2.5 001 6 3.8 4.2 16.9 100 ± 10 003 12 7.5 8.4 33.8 400 ± 40 005 24 14.9 16.8 67.7 1600 ± 160 007 48 30.0 33.6 135.3 6400 ± 640 009 60 37.2 42.0 169.1 10000 ± 1000 010 110 68.2 77.0 310.1 33610 ± 3360 012 Other coil versions available on request Uop cold= Operate voltage at 20 °C without pre-energizing the coil UI = Minimum voltage at 20 °C after pre-energizing with Unom without contact current UII = Maximum continuous voltage at 20 °C for Tc max = 115 °C without contact loading Unom = Nominal voltage Operating voltage limits UI and UII depend on temperature and can be calculated by: kI kII UI tamb = kI · UI 20 °C and UII tamb= kII · UII 20 °C tamb = UI tamb = UII tamb= kI a. kII = Tc max = Ambient temperature Minimum voltage at ambient temperature tamb Maximum voltage at ambient temperature tamb Factors (dependent on temperature), see diagram Maximum coil temperature Siemens AG Ambient temperature tamb 5 Miniature Power Relay IF - Faston General data Operate time at Unom and 20 °C, typ. Release time without/with diode in parallel, typ. Bounce time, make/break contact, typ. Maximum switching rate without load 10 ms 2 ms / 14 ms 1/2 ms 1200 min-1 Maximum switching rate with rated load 10 min-1 Ambient temperature range according to IEC 255 Part 1-00 or VDE 0435 Part 201 -40 °C ... +125 °C Thermal resistance Maximum permissible coil temperature Degree of protection according to IEC 529/ VDE 0470 Part 1 65 K/W 155 °C dust-protected IP 54 Electrical endurance 1 x 105 operations Mechanical endurance 3 x 107 operations Flammability according to UL 94 Solder bath temperature/max. duration Mounting position Weight (mass) V-0 260 °C / 5 s any approx. 26 g Insulation According to IEC 664/VDE 110 (1/89): rated voltage pollution severity overvoltage category 250 V 3 III According to VDE 0110 (2/79): insulation group/rated voltage C/250 B/380 Dielectric test voltage (1 min): contact/coil between open contacts Clearances/creepage distances Tracking resistance of the fundamental frame according to IEC 112 6 4000 V~rms 1000 V~rms 8 mm / 8 mm PTI 250 Siemens AG Miniature Power Relay IF - Faston Ordering code Block 1 Data position 1 2 3 4 5 Block 2 6 V 2 3 0 7 7 7 8 9 10 11 A 1 Block 3 12 13 14 15 A 4 Identifier for Miniature Power Relay IF - Faston Design A = dust-protected; PCB terminals (coil) and flat terminals (contacts) Version 1 = Standard Coil number 001 = 3 V– nominal voltage 003 = 6 V– 005 = 12 V– 007 = 24 V– 009 = 48 V– 010 = 60 V– 012 = 110 V– Type of contact A = Single contact Contact material 4 = AgCdO Contact arrangement 02 = 1 make contact 03 = 1 break contact Ordering example: V23077-A1005-A402 Miniature Power Relay IF, with 1 make contact, coil 12 V nominal voltage, contact material silver cadmium oxide (AgCdO) Note: Special designs can be carried out to customer specifications. Please contact your local representative. The addresses are given below. Siemens AG 7