MICROCIRCUIT DATA SHEET Original Creation Date: 02/12/97 Last Update Date: 05/17/99 Last Major Revision Date: 04/26/99 MV54ACT161-X REV 1A0 Synchronous Presettable Binary Counter General Description The ACT161 is a high-speed synchronous modulo-16 binary counter. It is synchronously presettable for application in programmable dividers and has two types of Count Enable inputs plus a Terminal Count output for versatility in forming synchronous multistage counters. The ACT161 has an asynchronous Master Reset Input that overrides all other inputs and forces the outputs LOW. Industry Part Number NS Part Numbers 54ACT161 54ACT161E-QMLV * 54ACT161ERQMLV* 54ACT161J-QMLV ** 54ACT161JRQMLV** 54ACT161W-QMLV *** 54ACT161WRQMLV*** Prime Die J161 Controlling Document 5962-91722 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Features - Synchronous counting and loading High-speed synchronous expansion Typical count rate of 125 MHz Outputs source/sink 24 mA ACT161 has TTL-compatible inputs Standard Military Drawing (SMD) - ACT161: 5962-9172201V2A*, VEA**, VFA*** - ACT161: 5962R9172201V2A*, VEA**, VFA*** 2 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vcc) -0.5V to +7.0V DC Input Vi = Vi = DC Input Diode Current (Iik) -0.5V Vcc +0.5V Voltage (Vi) -20 mA +20 mA -0.5V to Vcc +0.5V DC Output Diode Current (Iok) Vo = -0.5V Vo = Vcc +0.5V DC Output Voltage (Vo) -20 mA +20 mA -0.5V to Vcc +0.5V DC Output Source or Sink Current (Io) +50 mA DC Vcc or Ground Current per Output Pin (Icc or Ignd) +50 mA Storage Temperature (Tstg) -65 C to +150 C Junction Temperature (Tj) CDIP Thermal Resistance, junction-to-case (jc) 175 C see MIL-STD 1835 Maximum Power Dissipation (pd) 500 mW Lead Temperature (soldering, 10 seconds) +300 C Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT TM circuits outside databook specifications. Recommended Operating Conditions Supply Voltage (Vcc) 4.5V to 5.5V Input Voltage (Vi) 0V to Vcc Output Voltage (Vo) 0V to Vcc Operating Temperature (Ta) -55 C to +125 C Minimum ACT Vin Vcc Maximum Input Edge Rate (Delta V/Delta t) Devices from 0.8V to 2.0V @ 4.5V, 5.5V Low Level Input Voltage (Vil) 125 mV/ns 0.8 V Minimum High Level Input Voltage (Vih) 3.0 V Maximum High Level Output Current (Ioh) -24 mA Maximum Low Level Output Current (Iol) +24 mA 3 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Note 1: For dynamic operation, a Vih level between 2.0 V and 3.0 V may be recognized by this device as a high logic level input. For static operation, a Vih greater than or equal to 2.0 V will be recognized by this device as a high logic level input. Users are cautioned to verify that this will not affect their system. 4 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. SYMBOL VOL PARAMETER Low Level Output Voltage CONDITIONS NOTES ICCH ICCL ICCF ICCT IIH High Level Output Voltage Supply Current Outputs High Supply Current Outputs Low Supply Current Functional Supply Current High Level Input Current MIN MAX UNIT SUBGROUPS VCC=4.5V, IOL=50.0uA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 .10 V 1, 2, 3 VCC=5.5V, IOL=50.0uA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 .10 V 1, 2, 3 VCC=4.5V, IOL=24.0mA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 .40 V 1, 3 1, OUTPUT 5, 8 .50 V 2 1, OUTPUT 5, 8 .40 V 1, 3 1, OUTPUT 5, 8 .50 V 2 VCC=5.5V, IOL=24.0mA, VIL=0.8V, VIH=3.0V VOH PINNAME VCC=4.5V, IOH=-50.0uA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 4.40 V 1, 2, 3 VCC=5.5V, IOH=-50.0uA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 5.40 V 1, 2, 3 VCC=4.5V, IOH=-24.0mA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 3.70 V 1, 2, 3 VCC=5.5V, IOH=-24.0mA, VIL=0.8V, VIH=3.0V 1, OUTPUT 5, 8 4.70 V 1, 2, 3 VCC=5.5V, VIH=5.5V 1, VCC 2, 8 100 nA 1 1, VCC 2, 8 40 uA 2 1, VCC 2, 8 100 nA 1 1, VCC 2, 8 40 uA 2 1, VCC 2, 8 100 nA 1 1, VCC 2, 8 40 uA 2 1, VCC 5, 8 1.0 mA 1, 2 1, VCC 5, 8 1.6 mA 3 1, INPUT 2, 8 0.1 uA 1 1, INPUT 2, 8 1.0 uA 2 VCC=5.5V, VIL=0.0V VCC=5.5V, VIL=0.0V VCC=5.5V, VINH=3.4V VCC=5.5V, VIH=5.5V 5 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. SYMBOL IIL PARAMETER Low Level Input Current CONDITIONS NOTES VCC=5.5V, VIH=5.5V PINNAME MIN MAX UNIT SUBGROUPS 1, INPUT 2, 8 -0.1 uA 1 1, INPUT 2, 8 -1.0 uA 2 VIC+ Positive Input Clamp Voltage VCC=0.0V, IM=1.0mA 10, 11 INPUT 0.40 1.5 V 1 VIC- Negative Input Clamp Voltage VCC=0pen, IM=-1.0mA 10, 11 INPUT -0.40 -1.5 V 1 VIOL Dynamic output current LOW VCC=5.5V, IOL=50.0mA, VIL=0.0V, VIH=5.5V 1, OUTPUT 5, 8, 9 1.65 V 1, 2, 3 VIOH Dynamic Output Current HIGH VCC=5.5V, IOH=-50.0mA, VIL=0.0V, VIH=5.5V 1, OUTPUT 5, 8, 9 V 1, 2, 3 3.85 AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF, RL=500 OHMS, TRISE/TFALL=3.0nS, Temp Range: -55C to 125C. tpLH(1) tpHL(1) tpLH(2) tpHL(2) Propagation Delay Propagation Delay Propagation Delay Propagation Delay VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V 6 3, CP to 1.5 4, Qn 7, 8 (COUNT) 9.0 ns 9, 11 3, CP to 1.5 4, Qn 7, 8 (COUNT) 10.5 ns 10 3, CP to 1.5 4, Qn 7, 8 (COUNT) 9.5 ns 9, 11 3, CP to 1.5 4, Qn 7, 8 (COUNT) 10.5 ns 10 3, CP to 4, Qn 7, 8 (LOAD) 1.5 8.5 ns 9, 11 3, CP to 4, Qn 7, 8 (LOAD) 1.5 10.0 ns 10 3, CP to 4, Qn 7, 8 (LOAD) 1.5 8.0 ns 9, 11 3, CP to 4, Qn 7, 8 (LOAD) 1.5 9.5 ns 10 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF, RL=500 OHMS, TRISE/TFALL=3.0nS, Temp Range: -55C to 125C. SYMBOL tpLH(3) tpHL(3) tpLH(4) tpHL(4) tpHL(5) tpHL(6) Fmax(1) PARAMETER Propagation Delay Propagation Delay Propagation Delay Propagation Delay Propagation Delay Propagation Delay Maximum Count Frequency CONDITIONS NOTES VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V PINNAME MIN MAX UNIT SUBGROUPS 3, CP to 4, TC 7, 8 1.5 12.0 ns 9, 11 3, CP to 4, TC 7, 8 1.5 14.0 ns 10 3, CP to 4, TC 7, 8 1.5 11.0 ns 9, 11 3, CP to 4, TC 7, 8 1.5 12.5 ns 10 3, CET to 4, TC 7, 8 1.5 8.0 ns 9, 11 3, CET to 4, TC 7, 8 1.5 9.5 ns 10 3, CET to 4, TC 7, 8 1.5 8.5 ns 9, 11 3, CET to 4, TC 7, 8 1.5 9.5 ns 10 3, MR to 4, Qn 7, 8 1.5 8.5 ns 9, 11 3, MR to 4, Qn 7, 8 1.5 10.0 ns 10 3, MR to 4, TC 7, 8 1.5 10.0 ns 9, 11 3, MR to 4, TC 7, 8 1.5 11.5 ns 10 6, 8 CP 100 Mhz 9 6, 8 CP 85 Mhz 10, 11 tw(H/L)(1) Pulse Width (HIGH or LOW) VCC=4.5V 6, 8 CP(COUN 5.0 T) ns 9, 10, 11 tw(H/L)(2) Pulse Width (HIGH or LOW) VCC=4.5V 6, 8 CP(LOAD 5.0 ) ns 9, 10, 11 7 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF, RL=500 OHMS, TRISE/TFALL=3.0nS, Temp Range: -55C to 125C. SYMBOL PARAMETER tw(L)(3) Pulse Width (LOW) ts(H/L)(1) CONDITIONS NOTES VCC=4.5V Setup Time (HIGH or LOW) VCC=4.5V PINNAME MIN MAX UNIT SUBGROUPS 6, 8 MR 5.0 ns 9, 11 6, 8 MR 6.5 ns 10 6, 8 Pn to CP 9.5 ns 9, 11 6, 8 Pn to CP 13.0 ns 10 th(H/L)(1) Hold Time (HIGH or LOW) VCC=4.5V 6, 8 Pn to CP 0.0 ns 9, 10, 11 ts(H/L)(2) Setup Time (HIGH or LOW) VCC=4.5V 6, 8 PE to CP 8.5 ns 9, 11 6, 8 PE to CP 11.0 ns 10 th(H/L)(2) Hold Time (HIGH or LOW) VCC=4.5V 6, 8 PE to CP 0.0 ns 9, 10, 11 ts(H/L)(3) Setup Time or LOW) VCC=4.5V 6, 8 CET or CEP to CP 5.5 ns 9, 11 6, 8 CET or CEP to CP 7.0 ns 10 6, 8 CET or CEP to CP 0.5 ns 9, 10, 11 6, 8 MR to CP 0.0 ns 9, 11 6, 8 MR to CP 0.5 ns 10 (HIGH th(H/L)(3) Hold Time (HIGH or LOW) TREC(1) Recovery Time VCC=4.5V Note 1: SCREEN TESTED 100% ON EACH DEVICE AT +25C & +125C TEMPERATURE, SUBGROUPS 1, 2, 7, & 8. Note 2: SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMP SUBGROUPS A1, 2, 7 & 8. Note 3: SCREEN TESTED 100% ON EACH DEVICE AT +25C TEMPERATURE ONLY, SUBGROUP A9. Note 4: SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C, +125C, & -55C TEMPERATURE, SUBGROUPS A9, 10, & 11. Note 5: SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C, +125C, & -55C TEMPERATURE, SUBGROUPS A1, 2, 3, 7, & 8. Note 6: DESIGN CHARACTERIZATION DATA ONLY. Note 7: +25C & +125C MIN LIMITS GUARANTEED FOR 5.5V BY GUARDBANDING 4.5V MINIMUM LIMITS. Note 8: GENERAL NOTE: DUE TO THE INTERNAL NOISE PROBLEMS THIS COMPONENT CANNOT MEET THE THRESHOLD LIMITS REQUIRED PER MIL-STD-883, TEST METHOD 5005, FOR VIH (VIH=2.0V +20 PERCENT). FOR FUNTIONAL TESTS, USE VIH=3.0V + 5 PERCENT FOR ALL INPUTS. THE VIL LIMIT (0.8V - 50 PERCENT) REMAINS UNCHANGED. USERS ARE CAUTIONED TO VERIFY THAT THIS CHANGE WILL NOT AFFECT THEIR SYSTEMS. Note 9: TRANSMISSION LINE DRIVING TEST, GUARDBANDED LIMITS SET FOR +25 C, 2 MSEC DURATION MAX. Note 10: SCREEN TESTED 100% ON EACH DEVICE AT +25C TEMPERATURE ONLY, SUBGROUP A1. Note 11: SAMPLE TESTED (METHOD 5005, TABLE 1) AT +25C TEMPERATURE ONLY, SUBGROUP A1. 8 MICROCIRCUIT DATA SHEET MV54ACT161-X REV 1A0 Revision History Rev ECN # 1A0 M0003402 05/17/99 Rel Date Originator Changes Linda Collins Added the Rad Hard NSID's. Added ICCF to the DC electricals. Added VIC+ and VIC- to the DC electricals. Added notes 10 & 11 to the notes section. New update: MV54ACT161-X Rev. 1A0 9