DSDS1705/DS1706 DS1705/DS1706 3.3 and 5.0 Volt MicroMonitor FEATURES PIN ASSIGNMENT • Halts and restarts an out–of–control microprocessor • Holds microprocessor in check during power tran- sients • Automatically restarts microprocessor after power PBRST 1 8 WDS VCC 2 7 RST GND 3 6 ST IN 4 5 NMI failure 8–PIN DIP (300 MIL) • Monitors pushbutton for external override • Accurate 5%, 10% or 20% resets for 3.3 systems and 5% or 10% resets for 5.0 volt systems • Eliminates the need for discrete components WDS PBRST 1 8 VCC 2 7 RST (*RST) GND 3 6 ST IN 4 5 NMI • 3.3 volt 20% tolerance for use with 3.0 volt systems 8–PIN SOIC (150 MIL) • Pin compatible with the MAXIM MAX705/MAX706 in PBRST VCC GND IN 8–pin DIP and 8–pin SOIC • 8–pin DIP, 8–pin SOIC and 8–pin µ–SOP packages 1 2 3 4 8 7 6 5 WDS RST (*RST) ST NMI 8–PIN µ–SOP (118 MIL) • Industrial temperature range –40°C to +85°C See Mech. Drawings Section DS1705 and DS1706_/R/S/T (*DS1706L and DS1706P) PIN DESCRIPTION PBRST VCC GND IN NMI ST RST *RST WDS – – – – – – – – Pushbutton Reset Input Power Supply Ground Input Non–maskable Interrupt Strobe Input Active Low Reset Output Active High Reset Output (DS1706P and DS1706L only) – Watchdog Status Output DESCRIPTION The DS1705/DS1706 3.3 or 5.0 Volt MicroMonitor monitors three vital conditions for a microprocessor: power supply, software execution, and external override. A precision temperature compensated reference and comparator circuit monitors the status of VCC at the device and at an upstream point for maximum protection. When the sense input detects an out–of–tolerance Copyright 1995 by Dallas Semiconductor Corporation. All Rights Reserved. For important information regarding patents and other intellectual property rights, please refer to Dallas Semiconductor data books. condition a non–maskable interrupt is generated. As the voltage at the device degrades an internal power fail signal is generated which forces the reset to an active state. When VCC returns to an in–tolerance condition, the reset signal is kept in the active state for a minimum of 130 ms to allow the power supply and processor to stabilize. 062097 1/11 DS1705/DS1706 The second function the DS1705/DS1706 performs is pushbutton reset control. The DS1705/DS1706 debounces the pushbutton input and guarantees an active reset pulse width of 130 ms minimum. The third function is a watchdog timer. The DS1705/DS1706 has an internal timer that forces the WDO signal to the active state if the strobe input is not driven low prior to time–out. OPERATION Power Monitor The DS1705/DS1706 detects out–of–tolerance power supply conditions and warns a processor–based system of impending power failure. When VCC falls below the minimum VCC tolerance, a comparator outputs the RST (or RST) signal. RST (or RST) is an excellent control signal for a microprocessor, as processing is stopped at the last possible moment of valid VCC. On power–up, RST (or RST) are kept active for a minimum of 130 ms to allow the power supply and processor to stabilize. DS1705/DS1706 requires that the voltage at the IN pin be limited to VCC. Therefore, the maximum allowable voltage at the supply being monitored (VMAX) can also be derived as shown in Figure 5. A simple approach to solving the equation is to select a value for R2 high enough to keep power consumption low, and solve for R1. The flexibility of the IN input pin allows for detection of power loss at the earliest point in a power supply system, maximizing the amount of time for system shut– down between NMI and RST (or RST). When the supply being monitored decays to the voltage sense point, the DS1705/DS1706 pulses the NMI output to the active state for a minimum 200 µs. The NMI power fail detection circuitry also has built–in hysteresis of 100 µV. The supply must be below the voltage sense point for approximately 5 µs before a low NMI will be generated. In this way, power supply noise is removed from the monitoring function, preventing false interrupts. During a power–up, any detected IN pin levels below VTP by the comparator are disabled from generating an interrupt until VCC rises to VCCTP. As a result, any potential NMI pulse will not be initiated until VCC reaches VCCTP. Pushbutton Reset The DS1705/DS1706 provides an input pin for direct connection to a push–button reset (see Figure 2). The pushbutton reset input requires an active low signal. Internally, this input is debounced and timed such that a RST (or RST) signal of at least 130 ms minimum will be generated. The 130 ms delay commences as the pushbutton reset input is released from the low level. The push–button can be initiated by connecting the WDS or NMI outputs to the PBRST input as shown in Figure 3. Non–Maskable Interrupt The DS1705/DS1706 generates a non–maskable interrupt (NMI) for early warning of a power failure. A precision comparator monitors the voltage level at the IN pin relative to an on–chip reference generated by an internal band gap. The IN pin is a high impedance input allowing for a user–defined sense point. An external resistor voltage divider network (Figure 5) is used to interface with high voltage signals. This sense point may be derived from a regulated supply or from a higher DC voltage level closer to the main system power input. Since the IN trip point VTP is 1.25 volts, the proper values for R1 and R2 can be determined by the equation as shown in Figure 5. Proper operation of the 062097 2/11 Connecting NMI to PBRST would allow non–maskable interrupt to generate an automatic reset when an out– of–tolerance condition occurred in a monitored supply. An example is shown in Figure 3. Watchdog Timer The watchdog timer function forces WDS signals active when the ST input is not clocked within the 1 second time out period. Timeout of the watchdog starts when RST (or RST) becomes inactive. If a high–to–low transition occurs on the ST input pin prior to time–out, the watchdog timer is reset and begins to time–out again. If the watchdog timer is allowed to time out, the WDS signal is driven active (low) for a minimum of 130 ms. The ST input can be derived from many microprocessor outputs. The typical signals used are the microprocessors address signals, data signals, or control signals. When the microprocessor functions normally, these signals would, as a matter of routine, cause the watchdog to be reset prior to time–out. To guarantee that the watchdog timer does not time–out, a high–to–low transition must occur at or less than the minimum watchdog time–out of 1 second. A typical circuit example is shown in Figure 6. DS1705/DS1706 MICROMONITOR BLOCK DIAGRAM Figure 1 IN – DIGITAL SAMPLER + T.C. REFERENCE VCC PBRST NMI – DIGITAL SAMPLER + DIGITAL DELAY RST DS1706_/A/R/S/T RST DS1706L/DS1706P LEVEL SENSE AND DEBOUNCE WATCHDOG STATUS LATCH ST WDS PUSH–BUTTON RESET Figure 2 PBRST 8051 µP WDS VCC RST RST DS1706P ST GND ALE NMI IN PUSH–BUTTON RESET CONTROLLED BY NMI AND WDS Figure 3 UPSTREAM SUPPLY VOLTAGE VCC RST DS1706 GND IN µP WDS PBRST RST ST ALE NMI 062097 3/11 DS1705/DS1706 TIMING DIAGRAM: PUSHBUTTON RESET Figure 4 tPDLY PBRST tPB VIH VIL tRST RST VOH VOL RST NON–MASKABLE INTERRUPT CIRCUIT EXAMPLE Figure 5 PBRST WDS VCC VSENSE RST DS1706 ST GND R1 TO µP NMI IN R2 V SENSE R1 R2 x 1.25 R2 Example: Therefore: VSENSE = 4.50 volts at the trip point VCC = 3.3 volts 10KΩ = R2 4.50 x 3.3 12.4 volts maximum 1.25 4.5 R1 10K x 1.25 10K 062097 4/11 V MAX R1 26K V SENSE x V CC V TP DS1705/DS1706 WATCHDOG TIMER Figure 6 Z80 µP WDS PBRST VCC RST RST DS1706 MREQ ST GND DECODER NMI IN ADDRESS BUS TIMING DIAGRAM: STROBE INPUT Figure 7 INVALID STROBE INDETERMINATE STROBE VALID STROBE ST MIN. MAX. tTD WDS RST RESET INITIATED BY PUSHBUTTON TIMING DIAGRAM: NON–MASKABLE INTERRUPT Figure 8 VIN > 1.25V VTP(MAX) VTP VTP(MAX) VTP VTP(MIN) tIPD VTP(MIN) tIPD NMI VOH VOL 062097 5/11 DS1705/DS1706 TIMING DIAGRAM: POWER DOWN Figure 9 tF VCC VCCTP(MAX) VCCTP VCCTP(MIN) tRPD RST (DS1705 AND DS1706_/R/S/T) VOH VOL RST (DS1706L AND DS1706P ONLY) WDS WDS SLEWS WITH VCC 062097 6/11 RST SLEWS WITH VCC DS1705/DS1706 TIMING DIAGRAM: POWER UP Figure 10 VCCTP(MAX) VCCTP VCCTP(MIN) VCC tRPU RST RST RST VOH (DS1705 AND DS1706_/R/S/T) VOL RST (DS1706L AND DS1706P ONLY) WDS 062097 7/11 DS1705/DS1706 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on I/O Relative to Ground** Operating Temperature Storage Temperature Soldering Temperature –0.5V to +7.0V –0.5V to VCC + 0.5V –40°C to +85°C –55°C to +125°C 260°C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. **The voltage input on IN, ST, and PBRST can be exceeded if the input current is less than 10 mA. RECOMMENDED DC OPERATING CONDITIONS (–40°C to +85°C) PARAMETER SYMBOL MIN MAX UNITS NOTES Supply Voltage VCC 1.0 TYP 5.5 V 1 ST and PBRST Input High Level VIH 2.0 VCC–0.5 VCC+0.3 V 1, 3 1, 4 ST and PBRST Input Low Level VIL –0.03 +0.5 V 1 DC ELECTRICAL CHARACTERISTICS PARAMETER (–40°C to +85°C; VCC=1.2V to 5.5V) SYMBOL MIN TYP MAX UNITS NOTES VCC Trip Point DS1705/DS1706L VCCTP 4.50 4.65 4.75 V 1 VCC Trip Point DS1706 VCCTP 4.25 4.40 4.50 V 1 VCC Trip Point DS1706T VCCTP 3.00 3.08 3.15 V 1 VCC Trip Point DS1706S VCCTP 2.85 2.93 3.00 V 1 VCC Trip Point DS1706P or R VCCTP 2.55 2.63 2.70 V 1 Input Leakage IIL –1.0 +1.0 µA 2 Output Current @ 2.4 volts IOH µA 3 Output Current @ 0.4 volts IOL 10 mA 3 Output Voltage @ –500 µA VOH VCC+–0.3 V 3 Operating Current @ VCC < 5.5 volts ICC 60 µA 5 Operating Current @ VCC < 3.6 volts ICC 50 µA 5 IN Input Trip Point VTP 1.30 V 1 350 1.20 VCC–0.1 1.25 CAPACITANCE PARAMETER Input Capacitance Output Capacitance 062097 8/11 (tA=25°C) SYMBOL MIN TYP MAX UNITS CIN 5 pF COUT 7 pF NOTES DS1705/DS1706 AC ELECTRICAL CHARACTERISTICS (–40°C to +85°C; VCC=1.2V to 5.5V) PARAMETER SYMBOL MIN PBRST = VIL tPB 150 Reset Active Time tRST 130 ST Pulse Width tST 10 VCC Detect to RST and RST tRPD VCC Slew Rate VCC Detect to RST and RST 20 tRPU 130 tR 0 PBRST Stable Low to RST and RST 205 tTD VIN Detect to NMI tIPD 1.0 UNITS NOTES 285 8 ms ns 6 µs 9 µs 205 285 ms 7 ns tPDLY Watchdog Timeout MAX ns 5 tF VCC Slew Rate TYP 250 ns 1.6 2.2 s 8 5 8 µs 9 NOTES: 1. All voltages are referenced to ground. 2. PBRST is internally pulled up to VCC with an internal impedance of 40KΩ typical and the ST input is internally pulled up to VCC with an internal impedance of 180KΩ typical. 3. VCC 2.4 volts 4. VCC < 2.4 volts 5. Measured with outputs open and all inputs at VCC or ground. 6. Must not exceed tTD minimum. 7. tR = 5 µs 8. Minimum watchdog timeout tested at 2.7 volts for the 3.3 volt devices and 4.5 volts for the 5.0 volt devices. 9. Noise immunity – pulses < 2 µs at VCCTP minimum will not cause a reset. 062097 9/11 DS1705/DS1706 PART MARKING CODES 8 7 6 5 ABCD WWY 1 2 3 4 8–PIN µ–SOP (118 MIL) A, B, C and D represents the device type and tolerance. ABCD 705_ 706_ 706L 706P 706R 706S 706T – – – – – – – DS1705 DS1706 DS1706L DS1706P DS1706R DS1706S DS1706T WWY represents the device manufacturing Work Week, Year. 062097 10/11 DS1705/DS1706 DATA SHEET REVISION SUMMARY The following represent the key differences between 01/12/96 and 06/17/97 version of the DS1705/06 data sheet. Please review this summary carefully. 1. Page 8 add the following statement to the “Absolute Maximum Ratings” The voltage input limits on IN, ST, and PBRST can be exceeded if the input current is less than 10 mA. 062097 11/11