AD OP37

a
Low Noise, Precision, High Speed
Operational Amplifier (A VCL > 5)
OP37
The output stage has good load driving capability. A guaranteed
swing of 10 V into 600 Ω and low output distortion make the
OP37 an excellent choice for professional audio applications.
FEATURES
Low Noise, 80 nV p-p (0.1 Hz to 10 Hz)
3 nV/√Hz @ 1 kHz
Low Drift, 0.2 ␮V/ⴗC
High Speed, 17 V/␮s Slew Rate
63 MHz Gain Bandwidth
Low Input Offset Voltage, 10 ␮V
Excellent CMRR, 126 dB (Common-Voltage @ 11 V)
High Open-Loop Gain, 1.8 Million
Replaces 725, OP-07, SE5534 In Gains > 5
Available in Die Form
PSRR and CMRR exceed 120 dB. These characteristics, coupled
with long-term drift of 0.2 µV/month, allow the circuit designer
to achieve performance levels previously attained only by
discrete designs.
Low-cost, high-volume production of the OP37 is achieved by
using on-chip zener-zap trimming. This reliable and stable offset
trimming scheme has proved its effectiveness over many years of
production history.
GENERAL DESCRIPTION
The OP37 brings low-noise instrumentation-type performance to
such diverse applications as microphone, tapehead, and RIAA
phono preamplifiers, high-speed signal conditioning for data
acquisition systems, and wide-bandwidth instrumentation.
The OP37 provides the same high performance as the OP27,
but the design is optimized for circuits with gains greater than
five. This design change increases slew rate to 17 V/µs and
gain-bandwidth product to 63 MHz.
PIN CONNECTIONS
The OP37 provides the low offset and drift of the OP07
plus higher speed and lower noise. Offsets down to 25 µV and
drift of 0.6 µV/°C maximum make the OP37 ideal for precision instrumentation applications. Exceptionally low noise
(en= 3.5 nV/ @ 10 Hz), a low 1/f noise corner frequency of
2.7 Hz, and the high gain of 1.8 million, allow accurate
high-gain amplification of low-level signals.
8-Lead Hermetic DIP
(Z Suffix)
Epoxy Mini-DIP
(P Suffix)
8-Lead SO
(S Suffix)
The low input bias current of 10 nA and offset current of 7 nA
are achieved by using a bias-current cancellation circuit. Over
the military temperature range this typically holds IB and IOS
to 20 nA and 15 nA respectively.
VOS TRIM 1
8
VOS TRIM
–IN 2
7
V+
+IN 3
6
OUT
V– 4
5
NC
OP37
NC = NO CONNECT
SIMPLIFIED SCHEMATIC
V+
R3
Q6
R1*
1
8
VOS ADJ.
C2
R4
Q22
R2*
R23
Q21
Q24
Q23
Q46
C1
R24
R9
Q20
Q1A
Q1B
Q2B
Q19
OUTPUT
R12
Q2A
NON-INVERTING
INPUT (+)
C3
R5
C4
Q3
INVERTING
INPUT (–)
Q11
Q26
Q12
Q27
Q45
Q28
*R1 AND R2 ARE PERMANENTLY
ADJUSTED AT WAFER TEST FOR
MINIMUM OFFSET VOLTAGE.
V–
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
OP37
ABSOLUTE MAXIMUM RATINGS 4
ORDERING GUIDE
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
Internal Voltage (Note 1 ) . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
Output Short-Circuit Duration . . . . . . . . . . . . . . . . . Indefinite
Differential Input Voltage (Note2) . . . . . . . . . . . . . . . . . 0.7 V
Differential Input Current (Note 2) . . . . . . . . . . . . . . . . 25 mA
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
OP37A . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +1 25°C
OP37E (Z) . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to +85°C
OP37E, OP-37F (P) . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
OP37G (P, S, Z) . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering, 60 sec) . . . . . . . . 300°C
Junction Temperature . . . . . . . . . . . . . . . . . . –45°C to +150°C
␪JA3
␪JC
Unit
8-Lead Hermetic DIP (Z) 148
8-Lead Plastic DIP (P)
103
8-Lead SO (S)
158
16
43
43
°C/W
°C/W
°C/W
Package Type
TA = 25°C
VOS MAX
(µV)
25
25
60
100
100
CerDIP
8-Lead
OP37AZ*
OP37EZ
OP37GZ
Plastic
8-Lead
Operating
Temperature
Range
OP37EP
OP37FP*
OP37GP
OP37GS
MIL
IND/COM
IND/COM
XIND
XIND
*Not for new design, obsolete, April 2002.
NOTES
1
For supply voltages less than 22 V, the absolute maximum input voltage is equal
to the supply voltage.
2
The OP37’s inputs are protected by back-to-back diodes. Current limiting resistors
are not used in order to achieve low noise. If differential input voltage exceeds 0.7 V,
the input Current should be limited to 25 mA.
3
␪JA is specified for worst case mounting conditions, i.e., ␪JA is specified for device
in socket for TO, CerDIP, P-DIP, and LCC packages; ␪JA is specified for device
soldered to printed circuit board for SO package.
4
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the OP37 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions
are recommended to avoid performance degradation or loss of functionality.
–2–
WARNING!
ESD SENSITIVE DEVICE
REV. A
OP37
SPECIFICATIONS ( V = 15 V, T = 25C, unless otherwise noted.)
S
Parameter
Input Offset
Voltage
Long-Term
Stability
Input Offset
Current
Input Bias
Current
Input Noise
Voltage
Input Noise
Voltage Density
Input Noise
CurrentDensity
Input Resistance
Differential
Mode
Input Resistance
Common Mode
Input Voltage
Range
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Large Signal
Voltage Gain
Output Voltage
Swing
A
Min
OP37A/E
Typ Max
Min
OP37F
Typ Max
Min
OP37G
Typ Max
Symbol
Conditions
Unit
VOS
Note 1
10
25
20
60
30
100
µV
VOS/Time
Notes 2, 3
0.2
1.0
0.3
1.5
0.4
2.0
µV/Mo
IOS
7
35
9
50
12
75
nA
IB
± 10
± 40
± 12
± 55
± 15
± 80
nA
enp-p
1 Hz to 10 Hz3, 5
0.08
0.18
0.08
0.18
0.09
0.25
µV p-p
en
fO = 10 Hz3
fO = 30 Hz3
fO = 1000 Hz3
3.5
3.1
3.0
5.5
4.5
3.8
3.5
3.1
3.0
5.5
4.5
3.8
3.8
3.3
3.2
8.0
5.6
4.5
nV/√ Hz
iN
fO = 10 Hz3, 6
fO = 30 Hz3, 6
fO = 1000 Hz3, 6
1.7
1.0
0.4
4.0
2.3
0.6
1.7
1.0
0.4
4.0
2.3
0.6
1.7
1.0
0.4
0.6
RIN
Note 7
1.3
RINCM
6
0.9
3
IVR
45
0.7
2.5
pA/√ Hz
4
MΩ
2
GΩ
± 11
± 12.3
± 11
± 12.3
± 11
± 12.3
V
114
126
106
123
100
120
dB
CMRR
VCM = ± 11 V
PSSR
VS = ± 4 V
to ± 18 V
AVO
RL ≥ 2 kΩ,
VO = ± 10 V
RL ≥ 1 kΩ,
Vo = ± 10 V
RL ≥ 600 Ω,
VO = ± 1 V,
V S ± 44
RL ≥ 2 kΩ
RL ≥ 600 Ω
RL ≥ 2k Ω4
± 12.0 ± 13.8
± 10 ± 11.5
11
17
± 12.0 ± 13.8
± 10 ± 11.5
11
17
± 11.5 ± 13.5
± 10 ± 11.5
11
17
V
V
V/µs
fO = 10 kHz4
fO = 1 MHz
45
45
45
63
40
MHz
MHz
70
Ω
VO
Slew Rate
SR
Gain Bandwidth
Product
GBW
Open-Loop
Output Resistance RO
Power
Consumption
Pd
Offset Adjustment
Range
1
10
1
10
2
20
µV/ V
1000
1800
1000
1800
700
1500
V/m V
800
1500
800
1500
400
1500
V/m V
250
700
250
700
200
500
V/m V
63
40
VO = 0, IO = 0
70
VO = 0
90
RP = 10 kΩ
±4
63
40
70
140
90
±4
140
100
±4
170
mW
mV
NOTES
1
Input offset voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power. A/E grades guaranteed fully
warmed up.
2
Long term input offset voltage stability refers to the average trend line of V OS vs. Time over extended periods after the first 30 days of operation. Excluding the initial
hour of operation, changes in V OS during the first 30 days are typically 2.5 µV—refer to typical performance curve.
3
Sample tested.
4
Guaranteed by design.
5
See test circuit and frequency response curve for 0.1 Hz to 10 Hz tester.
6
See test circuit for current noise measurement.
7
Guaranteed by input bias current.
REV. A
–3–
OP37–SPECIFICATIONS
Electrical Characteristics ( V = 15 V, –55C < T < +125C, unless otherwise noted.)
S
Parameter
Input Offset
Voltage
Average Input
Offset Drift
Input Offset
Current
Input Bias
Current
Input Voltage
Range
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
A
Min
Conditions
VOS
Note 1
10 25
TCVOS
TCVOSN
Note 2
Note 3
0.2
IOS
15 50
IB
± 20
IVR
Large-Signal
Voltage Gain
CMRR
VCM = ± 10 V
PSRR
VS = ± 4.5 V to
± 18 V
AVO
Output Voltage
Swing
OP37A
Typ
Symbol
VO
Max
OP37C
Typ
Min
30
0.6
30
± 60
Max
100
µV
0.4
1.8
135
nA
± 35
± 150
Unit
µV/°C
nA
± 10.3
± 11.5
±± 10.2 ± 11.5
V
108
122
94
116
dB
2 16
4
51
µV/ V
RL ≥ 2 kΩ,
VO = ± 10 V
600
1200
300
800
V/m V
RL ≥ 2 kΩ
± 11.5
± 13.5
± 10.5
± 13.0
V
(VS = 15 V, –25C < TA < +85C for OP37EZ/FZ, 0C < TA < 70C for OP37EP/FP, and –40C < TA
Electrical Characteristics < +85C for OP37GP/GS/GZ, unless otherwise noted.)
Parameter
Input Offset
Voltage
Average Input
Offset Drift
Input Offset
Current
Input Bias
Current
Input Voltage
Range
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Large-Signal
Voltage Gain
Output Voltage
Swing
Symbol
Conditions
Min
OP37E
Typ
Max
Min
OP37F
Typ Max
Min
OP37C
Typ Max
Unit
20
50
40
140
55
220
µV
0.2
0.6
0.3
1.3
0.4
1.8
µV/°C
IOS
10
50
14
85
20
135
nA
IB
± 14
± 60
± 18
± 95
± 25
± 150
nA
VOS
TCVOS
TCVOSN
Note 2
Note 3
IVR
CMRR
VCM = ± 10 V
PSRR
VS = ± 4.5 V to
± 18 V
AVO
VO
± 10.5 ± 11.8
± 10.5 ± 11.8
± 10.5 ± 11.8
V
108
100
94
dB
122
2
RL ≥ 2 kΩ,
VO = ± 10 V
750
RL ≥ 2 kΩ
± 11.7 ± 13.6
15
1500
119
2
700
1300
± 11.4 ± 13.5
16
116
4
32
µV/ V
450
1000
V/mV
± 11
± 13.3
V
NOTES
1
Input offset voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power. A/E grades guaranteed fully
warmed up.
2
The TC VOS performance is within the specifications unnulled or when nulled withRP = 8 kΩ to 20 kΩ. TC VOS is 100% tested for A/E grades, sample tested for F/G grades.
3
Guaranteed by design.
–4–
REV. A
OP37
1.
2.
3.
4.
6.
7.
8.
Wafer Test Limits
Parameter
Input Offset
Voltage
Input Offset
Current
Input Bias
Current
Input Voltage
Range
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Large-Signal
Voltage Gain
NULL
(–) INPUT
(+) INPUT
V–
OUTPUT
V+
NULL
(VS = 15 V, TA = 25C for OP37N, OP37G, and OP37GR devices; TA = 125C for OP37NT and OP37GT devices,
unless otherwise noted.)
Symbol
Conditions
OP37NT
Limit
OP37N
Limit
OP37GT
Limit
OP37G
Limit
OP37GR
Limit
Unit
VOS
Note 1
60
35
200
60
100
µV MAX
IOS
50
35
85
50
75
nA MAX
IB
± 60
± 40
± 95
± 55
± 80
nA MAX
IVR
± 10.3
± 11
± 10.3
± 11
± 11
V MIN
108
114
100
106
100
dB MIN
10
10
10
20
µV/V MAX
CMRR
VCM = ± 11 V
PSRR
TA = 25°C,
VS = ± 4 V to
± 18 V
10
TA = 125°C,
VS = ± 4.5 V to
± 18 V
16
AVO
RL ≥ 2 kΩ,
VO = ± 10 V
RL ≥ 1 kΩ,
VO = ± 10 V
Output Voltage
Swing
VO
RL ≥ 2 kΩ
RL ≥ 600 kΩ
Power
Consumption
Pd
VO = 0
600
1000
500
800
± 11.5
µV/V MAX
20
± 12
± 10
1000
700
800
± 11
140
V/mV MIN
V/mV MIN
± 12
± 10
± 11.5
± 10
V MIN
V MIN
140
170
mW MAX
NOTES
For 25°C characterlstics of OP37NT and OP37GT devices, see OP37N and OP37G characteristics, respectively.
Electrical tests are performed at wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed
for standard product dice. Consult factory to negotiate specifications based on dice lot qualification through sample lot assembly and testing.
REV. A
–5–
OP37
Typical Electrical Characteristics (V = 15 V, T = 25C, unless otherwise noted.)
S
Parameter
Average Input
Offset Voltage
Drift
Average Input
Offset Current
Drift
Average Input
Bias Current
Drift
Input Noise
Voltage Density
OP37NT
Typical
OP37N
Typical
OP37GT
Typical
OP37G
Typical
OP37GR
Typical
Unit
TCVOS or Nulled or
Unnulled
TCVOSN
RP = 8 kΩ
to 20 kΩ
0.2
0.2
0.3
0.3
0.4
µV/°C
TCIOS
80
80
130
130
180
pA/°C
TCIB
100
100
160
160
200
pA/°C
fO = 10 Hz
fO = 30 Hz
fO = 1000 Hz
3.5
3.1
3.0
3.5
3.1
3.0
3.5
3.1
3.0
3.5
3.1
3.0
3.8
3.3
3.2
nV/√Hz
nV/√Hz
nV/√Hz
fO = 10 Hz
fO = 30 Hz
fO = 1000 Hz
1.7
1.0
0.4
1.7
1.0
0.4
1.7
1.0
0.4
1.7
1.0
0.4
1.7
1.0
0.4
pA/√ Hz
pA/√ Hz
pA/√ Hz
0.1 Hz to
10 Hz
RL ≥ 2k Ω
0.08
17
0.08
17
0.08
17
0.08
17
0.09
17
µV p-p
V/µs
fO = 10 kHz
63
63
63
63
63
MHz
Symbol
en
Input Noise
Current Density in
Input Noise
Voltage
A
en p-p
Slew Rate
SR
Gain Bandwidth
Product
GBW
Conditions
–6–
REV. A
Typical Performance Characteristics– OP37
VOLTAGE NOISE – nV/ Hz
90
70
60
50
TEST TIME OF 10sec MUST BE USED
TO LIMIT LOW FREQUENCY
(<0.1Hz) GAIN.
40
741
5
4
3
I/F CORNER = 2.7Hz
2
0.1
1
10
FREQUENCY – Hz
I/F CORNER
10 I/F CORNER =
LOW NOISE
2.7Hz
AUDIO OP AMP
OP37
I/F CORNER
INSTRUMENTATION AUDIO RANGE
RANGE TO DC
TO 20kHz
1
1
30
0.01
10
100
FREQUENCY – Hz
1
100
TPC 1. Noise-Tester Frequency
Response (0.1 Hz to 10 Hz)
1
1k
TPC 2. Voltage Noise Density vs.
Frequency
TOTAL NOISE – nV/ Hz
1
0.1
1k
5
R1
TA = 25C
VS = 15V
TA = 25C
VS = 15V
10
100
FREQUENCY – Hz
TPC 3. A Comparison of Op Amp
Voltage Noise Spectra
100
10
RMS VOLTAGE NOISE – V
TA = 25C
VS = 15V
VS = 15V
R2
VOLTAGE NOISE – nV/ Hz
GAIN – dB
80
100
10
9
8
7
6
VOLTAGE NOISE – nV/ Hz
100
RS – 2R1
10
AT 10Hz
AT 1kHz
4
AT 10Hz
3
AT 1kHz
2
RESISTOR NOISE ONLY
1k
10k
BANDWIDTH – Hz
100k
TPC 4. Input Wideband Voltage Noise
vs. Bandwidth (0.1 Hz to Frequency
Indicated)
1k
SOURCE RESISTANCE – 1
–50
10k
TPC 5. Total Noise vs. Source Resistance
4
AT 10Hz
AT 1kHz
3
2
0
10
20
30
40
1.0
TOTAL SUPPLY VOLTAGE (V+ – V–) – Volts
TPC 7. Voltage Noise Density vs.
Supply Voltage
REV. A
0.1
10
0
25
50
75
TEMPERATURE – C
100
125
5.0
4.0
TA = +125C
3.0
TA = –55C
2.0
TA = +25C
I/F CORNER = 140Hz
1
–25
TPC 6. Voltage Noise Density vs.
Temperature
10.0
TA = 25C
CURRENT NOISE – pA/ Hz
VOLTAGE NOISE – nV/ Hz
5
1
100
SUPPLY CURRENT – mA
0.01
100
1.0
100
1k
FREQUENCY – Hz
10k
TPC 8. Current Noise Density vs.
Frequency
–7–
5
15
25
35
TOTAL SUPPLY VOLTAGE – Volts
45
TPC 9. Supply Current vs. Supply
Voltage
OP37
OP37A
10
OP37B
OP37A
0
–10
OP37A
–20
–30
OP37B
–40
TRIMMING WITH
–50 10k POT DOES
NOT CHANGE
–60 TCV
OS
OP37C
–70
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE – C
4
2
0
–2
–4
–6
6
4
2
0
–2
–4
–6
0
1
2
3
4
5
15
10
DEVICE IMMERSED
IN 70C OIL BATH
40
30
OP37C
20
10
80
OP37B
100
80
60
40
20
102
OP37B
OP37A
–50 –25
0
25
50
75
0
–75 –50
100 125 150
103 104 105 106
FREQUENCY – Hz
107
108
TPC 16. Open-Loop Gain vs. Frequency
–25 0
25
50 75
TEMPERATURE – C
100
125
TPC 14. Input Bias Current vs. Temperature
TPC 15. Input Offset Current vs.
Temperature
PHASE MARGIN – DEG
TA = 25C
VS = 15V
RL 2k
10
OP37C
10
80
60
SLEW RATE – V/s
OPEN-LOOP VOLTAGE GAIN – dB
140
1
20
TEMPERATURE – C
TPC 13. Offset Voltage Change Due
to Thermal Shock
5
30
0
100
4
3
40
OP37A
60
2
VS = 15V
40
TIME – Seconds
120
1
50
30
90
VS = 15V
75
M
85
70
80
65
75
60
70
GBW
55
65
60
55
25
20
50
SLEW
45
15
10
–50
–25
0
25
50
75
100
40
125
TEMPERATURE – C
TPC 17. Slew Rate, Gain Bandwidth
Product, Phase Margin vs. Temperature
–8–
–80
TA = 25C
VS = 15V
50
30
–100
–120
40
GAIN – dB
20
0
TPC 12. Warm Up Offset Voltage Drift
GAIN-BANDWIDTH PRODUCT – MHz
F = 10kHz
0
OP37A/E
TIME AFTER POWER ON – MINUTES
INPUT OFFSET CURRENT – nA
INPUT BIAS CURRENT – nA
OPEN-LOOP GAIN – dB
TA = 70C
THERMAL SHOCK
RESPONSE BAND
0
–20
5
VS = +15V
25
5
OP37F
1
50
VS = +15V
20
OP37C/G
7
TPC 11. Long-Term Offset Voltage
Drift of Six Representative Units
30
TA =
25C
10
TIME – MONTHS
TPC 10. Offset Voltage Drift of Eight
Representative Units vs. Temperature
0
6
TA = 25C
VS = 15V
PHASE
MARGIN
= 71
–140
–160
20
AV = 5
10
–180
0
–200
–10
100k
1M
10M
FREQUENCY – Hz
–220
100M
TPC 18. Gain, Phase Shift vs. Frequency
REV. A
PHASE SHIFT – Degrees
30
20
CHANGE IN OFFSET VOLTAGE – V
OP37B
40
OFFSET VOLTAGE – V
6
OP37C
CHANGE IN INPUT OFFSET VOLTAGE – V
60
50
OP37
2.5
18
28
TA = 25C
VS = 15V
PEAK-TO-PEAK AMPLITUDE – Volts
2.0
RL = 2k
1.5
RL = 1k
1.0
0.5
0
0
10
20
30
40
24
20
16
12
8
4
0
104
50
POSITIVE
SWING
14
12
NEGATIVE
SWING
10
8
6
4
2
TA = 25C
VS = 15V
0
105
106
FREQUENCY – Hz
TOTAL SUPPLY VOLTAGE – Volts
TPC 19. Open-Loop Voltage Gain vs.
Supply Voltage
16
MAXIMUM OUTPUT – Volts
OPEN-LOOP GAIN – V/V
TA = 25C
–2
100
107
TPC 20. Maximum Output Swing vs.
Frequency
1k
LOAD RESISTANCE – 10k
TPC 21. Maximum Output Voltage
vs. Load Resistance
80
1µs
PERCENT OVERSHOOT
5V
60
0V
0
500
1000
1500
0V
TA = 25C
VS = 15V
AV = +5 (1k, 250)
–10V
VS = 15V
VIN = 20mV
AV = +5 (1k, 250)
20
0
+50mV
+10V
40
200ns
20mV
TA = 25C
VS = 15V
AV = +5
(1k, 250)
–50mV
2000
CAPACITIVE LOAD – pF
TPC 22. Small-Signal Overshoot vs.
Capacitive Load
16
120
CMRR – dB
50
COMMON-MODE RANGE – Volts
VS = 15V
TA = 25C
VCM = 10V
TA = 25C
VS = 15V
100
40
ISC(+)
30
80
ISC(–)
60
20
10
TPC 24. Small-Signal Transient
Response
140
60
SHORT-CIRCUIT CURRENT – mA
TPC 23. Large-Signal Transient
Response
0
1
2
3
4
5
TIME FROM OUTPUT SHORTED TO
GROUND – MINUTES
TPC 25. Short-Circuit Current vs. Time
REV. A
40
1k
TA = +25C
8
TA = +125C
4
0
TA = –55C
–4
TA = +25C
–8
100k
1M
FREQUENCY – Hz
10M
TPC 26. CMRR vs. Frequency
–9–
TA = +125C
–12
–16
10k
TA = –55C
12
0
5
10
15
20
SUPPLY VOLTAGE – Volts
TPC 27. Common-Mode Input Range
vs. Supply Voltage
OP37
2.4
0.1F
OPEN-LOOP VOLTAGE GAIN – V/V
1 SEC/DIV
100k
OP37
10 D.U.T.
2k
VOLTAGE
GAIN
= 50,000
4.3k 22F
OP12
SCOPE 1
RIN = 1M
4.7F
100k
2.2F
110k
0.1F
TPC 28. Noise Test Circuit (0.1 Hz to
10 Hz)
TPC 29. Low-Frequency Noise
TA = 25C
VS = 15V
AV = 5
VO = 20V p-p
1.6
1.4
1.2
1.0
0.8
0.6
100
NEGATIVE
SWING
60
POSITIVE
SWING
1k
10k
LOAD RESISTANCE – TA = 25C
AVCL = 5
VOLTAGE NOISE – V/s
18
120
SLEW RATE – V/V
POWER SUPPLY REJECTION RATIO – dB
1.8
100k
20
TA = 25C
40
2.0
TPC 30. Open-Loop Voltage Gain vs.
Load Resistance
19
160
80
TA = 25C
VS = 15V
0.4
100
24.3k
140
2.2
17
16
RISE
15
FALL
10
5
20
0
1
10
100
1k 10k 100k 1M 10M 100M
FREQUENCY – Hz
TPC 31. PSRP vs. Frequency
15
100
1k
10k
LOAD RESISTANCE – TPC 32. Slew Rate vs. Load
–10–
100k
0
3
6
9
12
15
18
SUPPLY VOLTAGE – Volts
21
TPC 33. Slew Rate vs. Supply Voltage
REV. A
OP37
APPLICATIONS INFORMATION
Noise Measurements
OP37 Series units may be inserted directly into 725 and OP07
sockets with or without removal of external compensation or
nulling components. Additionally, the OP37 may be fitted to
unnulled 741type sockets; however, if conventional 741 nulling
circuitry is in use, it should be modified or removed to ensure
correct OP37 operation. OP37 offset voltage may be nulled to
zero (or other desired setting) using a potentiometer (see offset
nulling circuit).
To measure the 80 nV peak-to-peak noise specification of the
OP37 in the 0.1 Hz to 10 Hz range, the following precautions
must be observed:
The OP37 provides stable operation with load capacitances of
up to 1000 pF and ± 10 V swings; larger capacitances should be
decoupled with a 50 Ω resistor inside the feedback loop. Closed
loop gain must be at least five. For closed loop gain between five
to ten, the designer should consider both the OP27 and the OP37.
For gains above ten, the OP37 has a clear advantage over the
unity stable OP27.
• For similar reasons, the device has to be well-shielded from
air currents. Shielding minimizes thermocouple effects.
Thermoelectric voltages generated by dissimilar metals at the input
terminal contacts can degrade the drift performance. Best
operation will be obtained when both input contacts are maintained at the same temperature.
10k RP
V+
–
OP37
OUTPUT
+
V–
Figure 1. Offset Nulling Circuit
The input offset voltage of the OP37 is trimmed at wafer level.
However, if further adjustment of VOS is necessary, a 10 kΩ trim
potentiometer may be used. TCVOS is not degraded (see offset
nulling circuit). Other potentiometer values from 1 kΩ to 1 MΩ
can be used with a slight degradation (0.1 µV/°C to 0.2 µV/°C) of
TCVOS. Trimming to a value other than zero creates a drift of
approximately (VOS/300) µV/°C. For example, the change in TCVOS
will be 0.33 µV/°C if VOS is adjusted to 100 µV. The offset voltage
adjustment range with a 10 kΩ potentiometer is ± 4 mV. If smaller
adjustment range is required, the nulling sensitivity can be reduced
by using a smaller pot in conjunction with fixed resistors. For
example, the network below will have a ± 280 µV adjustment range.
4.7k
• Sudden motion in the vicinity of the device can also
“feedthrough” to increase the observed noise.
• The test time to measure 0.1 Hz to l0 Hz noise should not
exceed 10 seconds. As shown in the noise-tester frequency
response curve, the 0.1 Hz corner is defined by only one zero.
The test time of ten seconds acts as an additional zero to eliminate
noise contributions from the frequency band below 0.1 Hz.
• A noise-voltage-density test is recommended when measuring
noise on a large number of units. A 10 Hz noise-voltage-density
measurement will correlate well with a 0.1 Hz-to-10 Hz peak-to-peak
noise reading, since both results are determined by the white
noise and the location of the 1/f corner frequency.
Optimizing Linearity
Best linearity will be obtained by designing for the minimum
output current required for the application. High gain and
excellent linearity can be achieved by operating the op amp with
a peak output current of less than ± 10 mA.
Instrumentation Amplifier
Offset Voltage Adjustment
1
• The device has to be warmed-up forat least five minutes. As
shown in the warm-up drift curve, the offset voltage typically
changes 4 µV due to increasing chip temperature after power up.
In the ten second measurement interval, these temperatureinduced effects can exceed tens of nanovolts.
1k POT
4.7k
A three-op-amp instrumentation amplifier provides high gain and
wide bandwidth. The input noise of the circuit below is 4.9 nV/√Hz.
The gain of the input stage is set at 25 and the gain of the second
stage is 40; overall gain is 1000. The amplifier bandwidth of
800 kHz is extraordinarily good for a precision instrumentation
amplifier. Set to a gain of 1000, this yields a gain bandwidth
product of 800 MHz. The full-power bandwidth for a 20 V p-p
output is 250 kHz. Potentiometer R7 provides quadrature
trimming to optimize the instrumentation amplifier’s ac commonmode rejection.
INPUT (–)
R5
500
0.1%
+
OP37
–
R1
8
5k
0.1%
R3
390
V+
Figure 2. TBD
R4
5k
0.1%
R2
100
+18V
INPUT (+)
C1
100pF
R7
100k
R6
500
0.1%
–
OP37
+
–
VOUT
OP37
+
R9
19.8k
R10
500
NOTES:
TRIM R2 FOR AVCL = 1000
TRIM R10 FOR dc CMRR
TRIM R7 FOR MINIMUM V OUT AT V CM = 20V p-p, 10kHz
OP37
Figure 4a. TBD
–18V
Figure 3. Burn-In Circuit
REV. A
R8
20k
0.1%
–11–
OP37
1k
140
TA = 25C
VS = 15V
VCM = 20V p-p
AC TRIM @ 10kHz
RS = 0
RS = 0
120
OP08/108
500
5534
p-p NOISE – nV
CMRR – dB
OP07
100
RS = 1k
BALANCED
80
RS = 100,
1k UNBALANCED
1
2
100
OP27/37
1 RS
e.g. RS
2 RS
e.g. RS
50
60
UNMATCHED
= R S1 = 10k, R S2 = 0
MATCHED
= 10k, R S1 = R S2 = 5k
RS1
RS2
REGISTER
NOISE ONLY
40
10
100
1k
10k
FREQUENCY – Hz
100k
10
50
1M
10k
500
1k
5k
RS – SOURCE RESISTANCE – 100
50k
Figure 4b. TBD
Figure 6. Peak-to-Peak Noise (0.1 Hz to 10 Hz) vs. Source
Resistance (Includes Resistor Noise)
The OP37 is a very low-noise monolithic op amp. The outstanding
input voltage noise characteristics of the OP37 are achieved
mainly by operating the input stage at a high quiescent current.
The input bias and offset currents, which would normally increase,
are held to reasonable values by the input bias current cancellation
circuit. The OP37A/E has IB and IOS of only ± 40 nA and 35 nA
respectively at 25°C. This is particularly important when the input
has a high source resistance. In addition, many audio amplifier
designers prefer to use direct coupling. The high IB. TCVOS of
previous designs have made direct coupling difficult, if not
impossible, to use.
At RS < 1 kΩ key the OP37’s low voltage noise is maintained.
With RS < 1 kΩ, total noise increases, but is dominated by the
resistor noise rather than current or voltage noise. It is only
beyond Rs of 20kil that current noise starts to dominate. The
argument can be made that current noise is not important for
applications with low to-moderate source resistances. The
crossover between the OP37 and OP07 and OP08 noise occurs
in the 15 kΩ to 40 kΩ region.
Comments on Noise
100
50
1
2
TOTAL NOISE – nV/ Hz
100
50
TOTAL NOISE – nV/ Hz
1
OP08/108
2
OP07
10
OP08/108
10
OP07
5534
1 RS
e.g. RS
2 RS
e.g. RS
5
OP27/37
UNMATCHED
= R S1 = 10k, R S2 = 0
MATCHED
= 10k, R S1 = R S2 = 5k
RS1
5
1 RS
e.g. RS
2 RS
e.g. RS
5534
OP27/37
UNMATCHED
= R S1 = 10k, R S2 = 0
MATCHED
= 10k, R S1 = R S2 = 5k
REGISTER
NOISE ONLY
1
50
RS1
REGISTER
NOISE ONLY
1
50
100
RS2
500
1k
5k
10k
RS – SOURCE RESISTANCE – 100
RS2
10k
500
1k
5k
RS – SOURCE RESISTANCE – 50k
Figure 7. !0 Hz Noise vs. Source resistance (Inlcludes
Resistor Noise)
50k
Figure 5. Noise vs. Resistance (Including Resistor Noise
@ 1000 Hz)
Voltage noise is inversely proportional to the square-root of bias
current, but current noise is proportional to the square-root of
bias current. The OP37’s noise advantage disappears when high
source-resistors are used. Figures 5, 6, and 7 compare OP-37
observed total noise with the noise performance of other devices
in different circuit applications.
Total noise = [( Voltage noise)2 + (current noise ⫻ RS)2 +
(resistor noise_]1/2
Figure 5 shows noise versus source resistance at 1000 Hz. The
same plot applies to wideband noise. To use this plot, just multiply
the vertical scale by the square-root of the bandwidth.
Figure 6 shows the 0.1 Hz to 10 Hz peak-to-peak noise. Here
the picture is less favorable; resistor noise is negligible, current
noise becomes important because it is inversely proportional to
the square-root of frequency. The crossover with the OP-07
occurs in the 3 kΩ to 5 kΩ range depending on whether balanced or unbalanced source resistors are used (at 3 kΩ the IB.
IOS error also can be three times the VOS spec.).
Therefore, for low-frequency applications, the OP07 is better
than the OP27/37 when Rs > 3 kΩ. The only exception is when
gain error is important. Figure 3 illustrates the 10 Hz noise. As
expected, the results are between the previous two figures.
For reference, typical source resistances of some signal sources
are listed in Table I.
–12–
REV. A
OP37
by only 0.7 dB. With a 1 kΩ source, the circuit noise measures
63 dB below a 1 mV reference level, unweighted, in a 20 kHz
noise bandwidth.
Table I. TBD
Device
Source
Impedance
Straln Gauge
<500 Ω
Magnetic
Tapehead
<1500 Ω
Comments
Gain (G) of the circuit at 1 kHz can be calculated by the expression:
Typically used in low-frequency
applications.
Low IB very important to reduce
set-magnetization problems when
direct coupling is used. OP37
IB can be neglected.
Similar need for low IB in direct
coupled applications. OP47 will not
introduce any self-magnetization
problem.
Used in rugged servo-feedback
applications. Bandwidth of interest
is 400 Hz to 5 kHz.
For the values shown, the gain is just under 100 (or 40 dB).
Lower gains can be accommodated by increasing R3, but gains
higher than 40 dB will show more equalization errors because of
the 8 MHz gain bandwidth of the OP27.
The following applications information has been abstracted from
a PMI article in the 12/20/80 issue of Electronic Design magazine
and updated.
Capacitor C3 and resistor R4form a simple –6 dB per octave
rumble filter, with a corner at 22 Hz. As an option, the switch
selected shunt capacitor C4, a nonpolarized electrolytic, bypasses
the low-frequency rolloff. Placing the rumble filter’s high-pass
action after the preamp has the desirable result of discriminating
against the RIAA amplified low frequency noise components
and pickup-produced low-frequency disturbances.
<1500 Ω
Magnetic
Phonograph
Cartridges
Linear Variable <1500 Ω
Differential
Transformer
Audio Applications
C4 (2)
220F
+
+
MOVING MAGNET
CARTRIDGE INPUT
Ra
47.5k
Ca
150pF
A1
OP27
C3
0.47F
R1
97.6k
R5
100k
LF ROLLOFF
OUT
R4
75k
IN
OUTPUT

R 
G = 0.101 1 + 1 
R3 

This circuit is capable of very low distortion over its entire range,
generally below 0.01% at levels up to 7 V rms. At 3 V output
levels, it will produce less than 0.03% total harmonic distortion
at frequencies up to 20 kHz.
A preamplifier for NAB tape playback is similar to an RIAA
phono preamp, though more gain is typically demanded, along
with equalization requiring a heavy low-frequency boost. The
circuit In Figure 4 can be readily modified for tape use, as
shown by Figure 5.
C1
0.03F
–
R2
7.87k
C2
0.01F
TAPE
HEAD
Ra
Ca
0.47F
OP37
+
R1
33k
R3
100
R2
5k
G = 1kHz GAIN
R1
= 0.101 ( 1 +
)
R3
= 98.677 (39.9dB) AS SHOWN
15k
0.01F
100k
T1 = 3180s
T2 = 50s
Figure 8. TBD
Figure 8 is an example of a phono pre-amplifier circuit using the
OP27 for A1; R1-R2-C1-C2 form a very accurate RIAA network with standard component values. The popular method to
accomplish RIAA phono equalization is to employ frequencydependent feedback around a high-quality gain block. Properly
chosen, an RC network can provide the three necessary time
constants of 3180 µs, 318 µs, and 75 µs.1
For initial equalization accuracy and stability, precision metalfilm resistors and film capacitors of polystyrene or polypropylene
are recommended since they have low voltage coefficients,
dissipation factors, and dielectric absorption.4 (High-K ceramic
capacitors should be avoided here, though low-K ceramics—
such as NPO types, which have excellent dissipation factors,
and somewhat lower dielectric absorption—can be considered
for small values or where space is at a premium.)
The OP27 brings a 3.2 nV/√Hz voltage noise and 0.45 pA/√Hz
current noise to this circuit. To minimize noise from other sources,
R3 is set to a value of 100 Ω, which generates a voltage noise of
1.3 nV/√Hz. The noise increases the 3.2 nV/√Hz of the amplifier
REV. A
Figure 9. TBD
While the tape-equalization requirement has a flat high frequency
gain above 3 kHz (t2 = 50 µs), the amplifier need not be stabilized
for unity gain. The decompensated OP37 provides a greater
bandwidth and slew rate. For many applications, the idealized
time constants shown may require trimming of RA and R2 to
optimize frequency response for non ideal tape head performance and other factors.5
The network values of the configuration yield a 50 dB gain at 1 kHz,
and the dc gain is greater than 70 dB. Thus, the worst-case output offset is just over 500 mV. A single 0.47 µF output capacitor
can block this level without affecting the dynamic range.
The tape head can be coupled directly to the amplifier input,
since the worst-case bias current of 85 nA with a 400 mH, 100 µin.
head (such as the PRB2H7K) will not be troublesome.
One potential tape-head problem is presented by amplifier biascurrent transients which can magnetize a head. The OP27 and
–13–
OP37
OP37 are free of bias-current transients upon power up or power
down. However, it is always advantageous to control the speed
of power supply rise and fall, to eliminate transients.
offset of this circuit will be very low, 1.7 mV or less, for a 40 dB
gain. The typical output blocking capacitor can be eliminated in
such cases, but is desirable for higher gains to eliminate switching
transients.
In addition, the dc resistance of the head should be carefully
controlled, and preferably below 1 kΩ. For this configuration,
the bias-current induced offset voltage can be greater than the
170 pV maximum offset if the head resistance is not sufficiently
controlled.
C2
1800pF
R1
121
A simple, but effective, fixed-gain transformerless microphone
preamp (Figure 10) amplifies differential signals from low impedance microphones by 50 dB, and has an input impedance of 2 kΩ.
Because of the high working gain of the circuit, an OP37 helps
to preserve bandwidth, which will be 110 kHz. As the OP37 is a
decompensated device (minimum stable gain of 5), a dummy
resistor, RP, may be necessary, if the microphone is to be
unplugged. Otherwise the 100% feedback from the open input
may cause the amplifier to oscillate.
A1
OP27
T1*
150
SOURCE
R2
1100
R3
100
OUTPUT
* T1 – JENSEN JE – 115K – E
JENSEN TRANSFORMERS
10735 BURBANK BLVD.
N. HOLLYWOOD, CA 91601
Figure 11. TBD
R1
1k
C1
5F
R6
100
Capacitor C2 and resistor R2 form a 2 µs time constant in this
circuit, as recommended for optimum transient response by
the transformer manufacturer. With C2 in use, A1 must have
unity-gain stability. For situations where the 2 µs time constant is not necessary, C2 can be deleted, allowing the faster
OP37 to be employed.
–
LOW IMPEDANCE
MICROPHONE INPUT
(Z = 50 TO 200 )
R3 = R4
R1 R2
R3
316k
Rp
30k
R2
1k
OP37
+
R7
10k
OUTPUT
R4
316k
Figure 10. TBD
Common-mode input-noise rejection will depend upon the match
of the bridge-resistor ratios. Either close-tolerance (0.1%) types
should be used, or R4 should be trimmed for best CMRR. All
resistors should be metal-film types for best stability and low noise.
Noise performance of this circuit is limited more by the input
resistors R1 and R2 than by the op amp, as R1 and R2 each
generate a 4 nV√Hz noise, while the op amp generates a 3.2 nV√Hz
noise. The rms sum of these predominant noise sources will be
about 6 nV√Hz, equivalent to 0.9 µV in a 20 kHz noise bandwidth,
or nearly 61 dB below a l mV input signal. Measurements confirm
this predicted performance.
For applications demanding appreciably lower noise, a high quality
microphone-transformer-coupled preamp (Figure 11) incorporates
the internally compensated. T1 is a JE-115K-E 150 Ω/15 kΩ
transformer which provides an optimum source resistance for
the OP27 device. The circuit has an overall gain of 40 dB, the
product of the transformer’s voltage setup and the op amp’s
voltage gain.
Some comment on noise is appropriate to understand the
capability of this circuit. A 150 Ω resistor and R1 and R2 gain
resistors connected to a noiseless amplifier will generate 220 nV
of noise in a 20 kHz bandwidth, or 73 dB below a 1 mV reference
level. Any practical amplifier can only approach this noise level;
it can never exceed it. With the OP27 and T1 specified, the
additional noise degradation will be close to 3.6 dB (or –69.5
referenced to 1 mV).
References
1. Lipshitz, S.P, “On RIAA Equalization Networks,” JAES, Vol. 27, June 1979,
p. 458-4S1.
2. Jung, W.G., IC Op Amp Cookbook, 2nd Ed., H.W. Sams and Company,
1980.
3. Jung, W.G., Audio /C Op Amp Applications, 2nd Ed., H.W. Sams and Company, 1978.
4. Jung, W.G., and Marsh, R.M., “Picking Capacitors.” Audio, February &
March, 1980.
5. Otala, M., “Feedback-Generated Phase Nonlinearity in Audio Amplifiers,”
London AES Convention, March 1980, preprint 197B.
6. Stout, D.F., and Kaufman, M., Handbook of Operational Amplifier Circuit
Design, New York, McGraw Hill, 1976.
Gain may be trimmed to other levels, if desired, by adjusting R2
or R1. Because of the low offset voltage of the OP27, the output
–14–
REV. A
OP37
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Hermetic DIP
(Z Suffix)
0.005 (0.13)
MIN
0.055 (1.4)
MAX
8
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
4
0.100 (2.54) BSC
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150
(3.81)
MIN
0.200 (5.08)
0.125 (3.18)
SEATING
0.023 (0.58) 0.070 (1.78) PLANE
0.014 (0.36) 0.030 (0.76)
0.015 (0.38)
0.008 (0.20)
15°
0°
Epoxy Mini-Dip
(P Suffix)
0.430 (10.92)
0.348 (8.84)
8
5
0.280 (7.11)
0.240 (6.10)
1
PIN 1
4
0.100 (2.54)
BSC
0.210
(5.33)
MAX
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558) 0.070 (1.77) SEATING
0.014 (0.356) 0.045 (1.15) PLANE
0.015 (0.381)
0.008 (0.204)
8-Lead SO
(S Suffix)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0196 (0.50)
45
0.0099 (0.25)
0.0500 (1.27)
BSC
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
REV. A
0.0688 (1.75)
0.0532 (1.35)
0.0192 (0.49)
0.0138 (0.35)
8
0.0500 (1.27)
0.0098 (0.25) 0
0.0160 (0.41)
0.0075 (0.19)
–15–
OP37
Revision History
Location
Page
Data Sheet changed from REV. B to REV. C.
Edits to ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to PIN CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Edits to PACKAGE TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Edits to ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C00319–0–2/02(A)
Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PRINTED IN U.S.A.
Edits to APPLICATIONS INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
–16–
REV. A