Back Subminiature Basic Switch SSG Subminiature Basic Switch Conforming to EN61058-1 (IEC1058-1), UL1054, and CSA C22.2 No.54 A wide operating temperature range of –25°C to 125°C is available for at high-temperature use. A wide variety of terminals: Solder, Tab (#110), and PCB Terminal Models. PCB Terminal Models are resistant to flux. Ordering Information Actuator Pin p plunger u ge Rating 0.1 A 5A Hinge ge lever e e 0.1 A 5A Simulated S u a ed hinge ge lever e e 0.1 A 5A Hinge ge roller o e lever e e 0.1 A 5A Note: OF max. Solder (see note) Tab (#110) PCB (see note) 1.50 N SSG-01H SSG-01T SSG-01P 0.50 N SSG-01H-5 SSG-01T-5 SSG-01P-5 1.50 N SSG-5H SSG-5T SSG-5P 0.50 N SSG-5H-5 SSG-5T-5 SSG-5P-5 0.60 N SSG-01L1H SSG-01L1T SSG-01L1P 0.20 N SSG-01L1H-5 SSG-01L1T-5 SSG-01L1P-5 0.60 N SSG-5L1H SSG-5L1T SSG-5L1P 0.20 N SSG-5L1H-5 SSG-5L1T-5 SSG-5L1P-5 0.60 N SSG-01L3H SSG-01L3T SSG-01L3P 0.20 N SSG-01L3H-5 SSG-01L3T-5 SSG-01L3P-5 0.60 N SSG-5L3H SSG-5L3T SSG-5L3P 0.20 N SSG-5L3H-5 SSG-5L3T-5 SSG-5L3P-5 0.60 N SSG-01L2H SSG-01L2T SSG-01L2P 0.20 N SSG-01L2H-5 SSG-01L2T-5 SSG-01L2P-5 0.60 N SSG-5L2H SSG-5L2T SSG-5L2P 0.20 N SSG-5L2H-5 SSG-5L2T-5 SSG-5L2P-5 EN61058-1 (IEC1058-1) approved by TÜV Rheinland. 95 SSG SSG Specifications Ratings 1. General Ratings Non-inductive load Resistive load Rated voltage NC Inductive laod Lamp load NO NC Inductive load NO NC Motor load NO NC NO 125 VAC 5 (0.1) A (see note 1) 1.5 A 0.7 A 3A 2.5 A 1.3 A 250 VAC 3A 1A 0.5 A 2A 1.5 A 0.8 A 8 VDC 5A 2A 5A 3A 14 VDC 5A 2A 4A 3A 30 VDC 4 (0.1) A (see note 1) 2A 3A 3A 125 VDC 0.4 A 0.05 A 0.4 A 0.05 A 250 VDC 0.2 A 0.03 A 0.2 A 0.05 A Note: 1. The values in the parentheses are for the SSG-01. 2. 3. 4. 5. 6. The above current ratings are the values of the steady-state current. Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC). Lamp load has an inrush current of 10 times the steady-state current. Motor load has an inrush current of 6 times the steady-state current. If the switch is used in a DC circuit and is subjected to a surge current, connect a surge suppressor across the switch. 2. TÜV Rheinland Approved Rating (EN61058-1/IEC1058-1) SSG-5 series: 5 A at 250 VAC (T125, 50,000 operations) SSG-01 series: 0.1 A at 30 VDC (T125, 50,000 operations) 3. UL, CSA Approved Rating SSG-5 series: 5 A at 125 VAC, 3 A at 250 VAC (6,000 operations) SSG-01 series: 0.1 A at 125 VAC, 0.1 A at 30 VDC (6,000 operations) Characteristics Operating speed 0.1 mm to 1 m/s (at pin plunger) Operating frequency Mechanical: 400 operations/min Electrical: 60 operations/min Insulation resistance 100 MΩ min. Contact resistance OF 1.50 N: SSG-5 series: 30 mΩ max. SSG-01 series:50 mΩ max. OF 0.50 N SSG-5 series: 50 mΩ max. SSG-01 series:100 mΩ max. Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between contacts of the same polarity (600 VAC for SSG-01H and SSG-01T series) 1,500 VAC, 50/60 Hz for 1 min between each terminal and ground 1,500 VAC, 50/60 Hz for 1 min between each terminal and non-current-carrying metal part Inrush current SSG-5: Vibration resistance Malfunction: 10 to 2,000 Hz, 196 m/s2 (20G) (Contact open: 10 µs max., lever position: at TTP) Shock resistance Malfunction: 490 m/s2 (approx. 50G) (Contact open: 10 µs max., lever position: at TTP) Life expectancy Mechanical: 10,000,000 operations min. (OT: rated value) Electrical: 200,000 operations min. (5 A at 125 VAC for SSG-5, 0.1 A at 125 VAC for SSG-01, resistive OT:full) Degree of protection (IP code) IP00 (IEC1058-1) Degree of protection against electrical shock Class I (IEC1058-1) Proof tracking index 175 V (IEC1058-1) Switch category (IEC335-1) D (IEC1058-1) 96 NO: NC: SSG–01: NO: NC: 20 A max. 10 A max. 1 A max. 1 A max. SSG SSG Contact Item SSG-5 SSG-01 Specification Rivet Crossbar Material Silver PGS alloy Safety Standards Certification body Standard File no. TÜV Rheinland EN61058-1 (IEC1058-1) T9451449 UL UL1054 E32667 CSA C22.2 No.54 LR21642 Operating Characteristics Solder/Tab Terminal Type Pin plunger Hinge lever Simulated hinge lever Hinge roller lever SSG-01j SSG-5j SSG-01j-5 SSG-5j-5 SSG-01L1j SSG-5L1j SSG-01L1j-5 SSG-5L1j-5 SSG-01L3j SSG-5L3j SSG-01L3j-5 SSG-5L3j-5 SSG-01L2j SSG-5L2j SSG-01L2j-5 SSG-5L2j-5 OF max. 1.50 N (153 gf) 0.50 N (51 gf) 0.60 N (61 gf) 0.20 N (20 gf) 0.60 N (61 gf) 0.20 N (20 gf) 0.60 N (61 gf) 0.20 N (20 gf) RF min. 0.25 N (25 gf) 0.04 N (4 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) PT max. 0.6 mm 1.0 mm 1.0 mm 1.0 mm OT min. 0.4 mm 0.8 mm 0.8 mm 0.8 mm MD max. 0.1 mm --- --- --- FP max. --- 13.6 mm 15.5 mm 19.0 mm OP 8.4±0.3 mm 8.8+1.0/–0.6 mm 10.7+1.0/–0.6 mm 14.5+1.0/–0.6 mm PCB Terminal Type Pin plunger SSG-01P SSG-5P Hinge lever Simulated hinge lever Hinge roller lever SSG-01P-5 SSG-5P-5 SSG-01L1P SSG-5L1P SSG-01L1P-5 SSG-5L1P-5 SSG-01L3P SSG-5L3P SSG-01L3P-5 SSG-5L3P-5 SSG-01L2P SSG-5L2P SSG-01L2P-5 SSG-5L2P-5 OF max. 1.50 N (153 gf) 0.50 N (51 gf) 0.60 N (61 gf) 0.20 N (20 gf) 0.60 N (61 gf) 0.20 N (20 gf) 0.60 N (61 gf) 0.20 N (20 gf) RF min. 0.25 N (25 gf) 0.04 N (4 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) 0.06 N (6 gf) 0.02 N (2 gf) PT max. 0.6 mm 1.0 mm 1.0 mm 1.0 mm OT min. 0.4 mm 0.8 mm 0.8 mm 0.8 mm MD max. 0.1 mm --- --- --- FP max. --- 17.0 mm 18.9 mm 22.4 mm OP 11.8±0.4 mm 12.2+1.1/–0.7 mm 14.4+1.1/–0.7 mm 17.9+1.1/–0.7 mm 97 SSG SSG Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Every actual model number includes the code instead of j for the kind of terminals incorporated by the model. 3. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Terminal Model Solder/Tab Terminal Pin Plunger SSG-01j SSG-5j SSG-01j-5 SSG-5j-5 7.5±0.3 PT 3.5 1.8 2.2 +0.1 0 7.7 OP 6.9 2.2 C 6.1 2.5 dia. 5.1 1.6 (see note) NO NC 2.2 +0.1 0 dia. hole 9.5±0.1 8.9 7.2 (see note) (see note) 19.8 3.2 6.4±0.2 0.5 Three, 1.6 dia. holes Note: At switch bottom Hinge Lever SSG-01L1j SSG-5L1j SSG-01L1j-5 SSG-5L1j-5 3.6 5.3±0.4 t0.3 Stainless lever +0.1 2.2 0 OP 6.9 7.7 2.2 C NO FP NC 6.1 +0.1 0 2.2 2.5 dia. dia. hole 3.2 6.4+0.2 9.5±0.1 5.1 1.6 (see note) 8.9 7.2 (see note) (see note) 19.8 Three, 1.6 dia. holes 0.5 Note: At switch bottom Simulated Hinge Lever SSG-01L3j SSG-5L3j SSG-01L3j-5 SSG-51L3j-5 3.6 6.3±0.4 R 1.3 t0.3 Stainless lever FP +0.1 OP 2.2 0 2.2 6.1 6.9 7.7 C NO NC 2.2 2.5 dia. 5.1 1.6 (see note) +0.1 0 dia. hole 9.5±0.1 8.9 7.2 (see note)(see note) 0.5 3.2 6.4±0.2 Three, 1.6 dia. holes 19.8 Note: 98 At switch bottom SSG SSG Hinge Roller Lever SSG-01L2j SSG-5L2j SSG-01L2j-5 SSG-5L2j-5 3.8 4.8 × 3.2 dia. Acetal resin roller 5±0.4 t0.3 Stainless lever OP +0.1 2.2 –0 2.2 FP 6.9 7.7 C NO NC 6.1 +0.1 2.2 0 dia. hole Three, 1.6 dia. holes 2.5 dia. 5.1 1.6 (see note) 9.5±0.1 7.2 8.9 (see note) (see note) 19.8 3.2 6.4±0.2 0.5 Note: At switch bottom PCB Terminal Pin Plunger SSG-01P SSG-5P SSG-01P-5 SSG-5P-5 4.8±0.3 PT 2.87±0.1 3.5 1.8 2.2 +0.1 –0 3.4±0.1 6.9 7.7 C NO OP NC 2.2 +0.1 0 dia. hole 2.5 dia. 5.15 7.62±0.2 Three, 1.2±0.1 1.3±0.3 0.5±0.05 Three, 0.8 6.4±0.2 7.62±0.2 9.5±0.1 1.8 4±0.3 19.8 Hinge Lever SSG-01L1P SSG-5L1P SSG-01L1P-5 SSG-5L1P-5 3.6 5.3±0.4 t0.3 Stainless lever 2.87±0.1 +0.1 2.2 0 3.4±0.1 6.9 7.7 C NO FP OP NC +0.1 2.5 dia. 5.15 7.62±0.2 9.5±0.1 2.2 0 dia. hole Three, 1.2±0.1 Three, 0.8 7.62±0.2 1.3±0.3 0.5±0.05 6.4±0.2 1.8 4±0.3 19.8 99 SSG SSG Simulated Hinge Lever SSG-01L3P SSG-5L3P SSG-01L3P-5 SSG-51L3P-5 3.6 R 1.3 6.3±0.4 t0.3 Stainless lever 2.87±0.1 +0.1 2.2 0 3.4±0.1 6.9 7.7 OP C NO FP NC +0.1 2.5 dia. 5.15 7.62±0.2 2.2 0 dia. hole Three, 1.2±0.1 Three, 0.8 7.62±0.2 9.5±0.1 1.3±0.3 0.5±0.05 6.4±0.2 1.8 4±0.3 19.8 Hinge Roller Lever SSG-01L2P SSG-5L2P SSG-01L2P-5 SSG-5L2P-5 3.8 4.8 × 3.2 dia. Acetal resin roller 5±0.4 t0.3 Stainless lever 2.87±0.1 OP 2.2 +0.1 0 3.4±0.1 6.9 7.7 C NO FP NC +0.1 2.5 dia. 5.15 7.62±0.2 9.5±0.1 19.8 100 2.2 0 dia. hole Three, 1.2±0.1 Three, 0.8 7.62±0.2 1.3±0.3 0.5±0.05 6.4±0.2 1.8 4±0.3 SSG SSG Kind of Terminals Solder Terminals Tab Terminals (#110) 7.5±0.3 PT 1.8 2.2 +0.1 0 PT C NO 3.5 1.8 +0.1 6.9 2.2 6.1 7.5±0.3 3.5 2.2 0 7.7 OP 6.9 7.7 OP 2.2 C NC NO NC 10.6 7.1 2.5 dia. 5.1 1.6 (see note) 2.2 +0.1 0 dia. hole 9.5±0.1 8.9 7.2 (see note) (see note) 19.8 0.5 3.2 6.4±0.2 Three, 1.6 dia. holes Note: 2.5 dia. 5.1 1.6 (see note) At switch bottom 2.2 +0.1 dia. hole 0 9.5±0.1 8.9 7.2 (see note) (see note) 19.8 Note: Three, 1.2 dia. holes 2.8±0.2 3.2 6.4±0.2 0.5 At switch bottom PCB Terminals PCB Mounting Three, 1.35 dia. to 1.5 dia. 4.8±0.3 PT 2.87±0.1 3.5 1.8 +0.1 2.2 –0 3.4±0.1 6.9 7.7 C NO 2.78±0.1 OP 9.5±0.1 7.62±0.1 NC 15.24±0.1 +0.1 2.2 0 2.5 dia. 5.15 7.62±0.2 9.5±0.1 dia. hole Three, 1.2±0.1 1.3±0.3 0.5±0.05 Three, 0.8 6.4±0.2 7.62±0.2 1.8 4±0.3 19.8 101 SSG SSG Precautions Mounting Actuating Use two 2.2 mounting screws with spring washers to mount the switch. Tighten the screws to a torque of 0.20 to 0.25 N S m (2 to 2.5 kgf S cm). Make sure that the operating speed and frequency are within the permissible range of the switch. 1. Do not use the switch in an application where the operating speed is extremely slow or the switching operation could become unstable or malfunctioning could result due to contact failure or contact welding. 2. Do not use the switch in an application where the operating speed is too fast, or the switch will be broken due to a shock or the movable contact will not keep up with the speed. The reliability of a switch is maintained within the permissible operating speed and frequency of the switch. The life of a switch is determined at a specified operating speed, therefore, it varies with the actual operating speed and frequency. The switch should be set so that its stroke will be in the range of 60% to 90% of the rated OT when the switch is operated. The stroke must not exceed the rated OT value. Malfunctioning can result if the switch is set with its stroke exceeding the rated OT. Therefore the proper adjustment of the mounting position is essential when installing the switch. Do not apply excessive force to the actuator. Be very careful not to apply force in the opposite and lateral directions relative to the operating direction. Mounting Holes 9.5±0.1 The switch does not have a ground terminal. The minimum distance through insulation (IEC1058-1) is 0.9 mm. If proper insulation for the end product cannot be secured, additional insulation such as a separator or insulation cover should be attached. Soldering When soldering switch terminals, apply a soldering iron rated at 60 W max. and finish soldering quickly within 3 seconds. During soldering and 1 minute after soldering, do not apply external force to the terminals. Solder terminal is provided with a hole so that a conductor can be secured mechanically. The conductors for a soldering terminal (H type) should be flexible and its cross section should be AWG18 to 20 for the SSG-5H Series and AWG20 to 22 for the SSG-01H Series. To automatically solder the switch to a PCB in a soldering bath, complete soldering within 5 seconds at a flux temperature of 250°C and avoid the overflow of flux onto the surface of the PCB where the switch or other parts are mounted. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. B096-E1-1 102