AD ADCLK950BCPZ

Two Selectable Inputs, 10 LVPECL Outputs,
SiGe Clock Fanout Buffer
ADCLK950
FEATURES
FUNCTIONAL BLOCK DIAGRAM
2 selectable differential inputs
4.8 GHz operating frequency
75 fs rms broadband random jitter
On-chip input terminations
3.3 V power supply
LVPECL
ADCLK950
Q0
Q0
Q1
Q1
APPLICATIONS
Q2
Q2
VREF 0
Q3
REFERENCE
Q3
Q4
VT0
Q4
CLK0
GENERAL DESCRIPTION
The ADCLK950 is an ultrafast clock fanout buffer fabricated
on the Analog Devices, Inc., proprietary XFCB3 silicon germanium (SiGe) bipolar process. This device is designed for high
speed applications requiring low jitter.
The device has two selectable differential inputs via the IN_SEL
control pin. Both inputs are equipped with center tapped,
differential, 100 Ω on-chip termination resistors. The inputs
accept dc-coupled LVPECL, CML, 3.3 V CMOS (single-ended),
and ac-coupled 1.8 V CMOS, LVDS, and LVPECL inputs. A
VREFx pin is available for biasing ac-coupled inputs.
The ADCLK950 features 10 full-swing emitter coupled logic
(ECL) output drivers. For LVPECL (positive ECL) operation,
bias VCC to the positive supply and VEE to ground. For ECL
operation, bias VCC to ground and VEE to the negative supply.
CLK0
Q5
VT1
Q5
CLK1
Q6
CLK1
Q6
Q7
IN_SEL
VREF 1
Q7
REFERENCE
Q8
Q8
Q9
Q9
08279-001
Low jitter clock distribution
Clock and data signal restoration
Level translation
Wireless communications
Wired communications
Medical and industrial imaging
ATE and high performance instrumentation
Figure 1.
The output stages are designed to directly drive 800 mV each
side into 50 Ω terminated to VCC − 2 V for a total differential
output swing of 1.6 V.
The ADCLK950 is available in a 40-lead LFCSP and specified
for operation over the standard industrial temperature range of
−40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADCLK950
TABLE OF CONTENTS
Features .............................................................................................. 1 Pin Configuration and Function Descriptions..............................6 Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................7 General Description ......................................................................... 1 Functional Description .....................................................................9 Functional Block Diagram .............................................................. 1 Clock Inputs ...................................................................................9 Revision History ............................................................................... 2 Clock Outputs ................................................................................9 Specifications..................................................................................... 3 Clock Input Select (IN_SEL) Settings...................................... 10 Electrical Characteristics ............................................................. 3 PCB Layout Considerations ...................................................... 10 Absolute Maximum Ratings............................................................ 5 Input Termination Options ....................................................... 11 Determining Junction Temperature .......................................... 5 Outline Dimensions ....................................................................... 12 ESD Caution .................................................................................. 5 Ordering Guide .......................................................................... 12 Thermal Performance .................................................................. 5 REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADCLK950
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Typical (Typ column) values are given for VCC − VEE = 3.3 V and TA = 25°C, unless otherwise noted. Minimum (Min column) and maximum
(Max column) values are given over the full VCC − VEE = 3.3 V ± 10% and TA = −40°C to +85°C variation, unless otherwise noted.
Table 1. Clock Inputs and Outputs
Parameter
DC INPUT CHARACTERISTICS
Input Common Mode Voltage
Input Differential Range
Input Capacitance
Input Resistance
Single-Ended Mode
Differential Mode
Common Mode
Input Bias Current
Hysteresis
DC OUTPUT CHARACTERISTICS
Output Voltage High Level
Output Voltage Low Level
Output Voltage Differential
Reference Voltage
Output Voltage
Output Resistance
Symbol
Min
VICM
VID
CIN
VEE + 1.5
0.4
VOH
VOL
VOD
VREF
Typ
Max
Unit
Test Conditions/Comments
VCC − 0.1
3.4
±1.7 V between input pins
0.4
V
V p-p
pF
50
100
50
20
10
Ω
Ω
kΩ
μA
mV
Open VTx
V
V
mV
50 Ω to (VCC − 2.0 V)
50 Ω to (VCC − 2.0 V)
50 Ω to (VCC − 2.0 V)
V
Ω
−500 μA to +500 μA
Unit
Test Conditions/Comments
GHz
See Figure 4 for differential output voltage
vs. frequency, >0.8 V differential output
swing
20% to 80% measured differentially
VCC − 1.26
VCC − 1.99
610
VCC − 0.76
VCC − 1.54
960
(VCC + 1)/2
235
Table 2. Timing Characteristics
Parameter
AC PERFORMANCE
Maximum Output Frequency
Symbol
Output Rise Time
Output Fall Time
Propagation Delay
Temperature Coefficient
Output-to-Output Skew 1
Part-to-Part Skew
Additive Time Jitter
Integrated Random Jitter
Broadband Random Jitter 2
Crosstalk-Induced Jitter 3
CLOCK OUTPUT PHASE NOISE
Absolute Phase Noise
tR
tF
tPD
fIN = 1 GHz
Min
Typ
4.5
4.8
40
40
175
75
75
210
50
9
Max
90
90
245
28
45
28
75
90
ps
ps
ps
fs/°C
ps
ps
fs rms
fs rms
fs rms
−119
−134
−145
−150
−150
1
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
VICM = 2 V, VID = 1.6 V p-p
VID = 1.6 V p-p
BW = 12 kHz − 20 MHz, CLK = 1 GHz
VID = 1.6 V p-p, 8 V/ns, VICM = 2 V
Input slew rate > 1 V/ns (see Figure 11, the
phase noise plot, for more details)
@100 Hz offset
@1 kHz offset
@10 kHz offset
@100 kHz offset
>1 MHz offset
The output skew is the difference between any two similar delay paths while operating at the same voltage and temperature.
Measured at the rising edge of the clock signal; calculated using the SNR of the ADC method.
3
This is the amount of added jitter measured at the output while two related, asynchronous, differential frequencies are applied to the inputs.
2
Rev. 0 | Page 3 of 12
ADCLK950
Table 3. Input Select Control Pin
Parameter
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Capacitance
Symbol
VIH
VIL
IIH
IIL
Min
VCC − 0.4
VEE
Typ
2
Max
VCC
1
100
0.6
Unit
V
V
μA
mA
pF
Table 4. Power
Parameter
POWER SUPPLY
Supply Voltage Requirement
Power Supply Current
Negative Supply Current
Positive Supply Current
Power Supply Rejection 1
Output Swing Supply Rejection 2
1
2
Symbol
Min
VCC − VEE
2.97
IVEE
IVCC
PSRVCC
PSRVCC
Typ
106
346
<3
28
Change in tPD per change in VCC.
Change in output swing per change in VCC.
Rev. 0 | Page 4 of 12
Max
Unit
Test Conditions/Comments
3.63
V
130
390
mA
mA
ps/V
dB
3.3 V + 10%
Static
VCC − VEE = 3.3 V ± 10%
VCC − VEE = 3.3 V ± 10%
VCC − VEE = 3.3 V ± 10%
VCC − VEE = 3.3 V ± 10%
ADCLK950
ABSOLUTE MAXIMUM RATINGS
DETERMINING JUNCTION TEMPERATURE
Table 5.
Parameter
Supply Voltage
VCC − VEE
Input Voltage
CLK0, CLK1, CLK0, CLK1, IN_SEL
CLK0, CLK1, CLK0, CLK1 to VTx Pin (CML,
LVPECL Termination)
CLK0, CLK1 to CLK0, CLK1
Input Termination, VTx to CLK0, CLK1, CLK0,
and CLK1
Maximum Voltage on Output Pins
Maximum Output Current
Voltage Reference (VREFx)
Operating Temperature Range
Ambient
Junction
Storage Temperature Range
To determine the junction temperature on the application
printed circuit board (PCB), use the following equation:
Rating
6V
TJ = TCASE + (ΨJT × PD)
where:
TJ is the junction temperature (°C).
TCASE is the case temperature (°C) measured by the customer at
the top center of the package.
ΨJT is from Table 6.
PD is the power dissipation.
VEE − 0.5 V to
VCC + 0.5 V
±40 mA
±1.8 V
±2 V
Values of θJA are provided for package comparison and PCB
design considerations. θJA can be used for a first-order approximation of TJ by the equation
VCC + 0.5 V
35 mA
VCC to VEE
TJ = TA + (θJA × PD)
where TA is the ambient temperature (°C).
−40°C to +85°C
150°C
−65°C to +150°C
Values of θJB are provided in Table 6 for package comparison
and PCB design considerations.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
THERMAL PERFORMANCE
Table 6.
Parameter
Junction-to-Ambient Thermal Resistance
Still Air
0 m/sec Air Flow
Moving Air
1 m/sec Air Flow
2.5 m/sec Air Flow
Junction-to-Board Thermal Resistance
Moving Air
1 m/sec Air Flow
Junction-to-Case Thermal Resistance
Moving Air
Die-to-Heatsink
Junction-to-Top-of-Package Characterization Parameter
Still Air
0 m/sec Air Flow
1
Symbol
Description
Value 1
Unit
46.1
°C/W
40.3
36.2
°C/W
°C/W
28.7
°C/W
8.3
°C/W
0.6
°C/W
θJA
Per JEDEC JESD51-2
θJMA
Per JEDEC JESD51-6
θJB
Per JEDEC JESD51-8
θJC
Per MIL-STD 883, Method 1012.1
ΨJT
Per JEDEC JESD51-2
Results are from simulations. The PCB is a JEDEC multilayer type. Thermal performance for actual applications requires careful inspection of the conditions in the
application to determine if they are similar to those assumed in these calculations.
Rev. 0 | Page 5 of 12
ADCLK950
40
39
38
37
36
35
34
33
32
31
VCC
Q0
Q0
Q1
Q1
Q2
Q2
Q3
Q3
VCC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
IN_SEL 1
CLK0 2
CLK0 3
VREF 0 4
VT0 5
CLK1 6
CLK1 7
VT1 8
VREF 1 9
VEE 10
ADCLK950
VCC
NC
NC
Q4
Q4
Q5
Q5
NC
NC
VCC
NOTES
1. NC = NO CONNECT.
2. EPAD MUST BE SOLDERED TO VEE POWER PLANE.
08279-002
VCC
Q9
Q9
Q8
Q8
Q7
Q7
Q6
Q6
VCC
11
12
13
14
15
16
17
18
19
20
TOP VIEW
(Not to Scale)
30
29
28
27
26
25
24
23
22
21
Figure 2. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11, 20, 21,
30, 31, 40
12, 13
14, 15
16, 17
18, 19
22, 23, 28,
29
24, 25
26, 27
32, 33
34, 35
36, 37
38, 39
(41)
Mnemonic
IN_SEL
CLK0
CLK0
VREF0
VT0
CLK1
CLK1
VT1
VREF1
VEE
VCC
Description
Input Select. Logic 0 selects CLK0 and CLK0 inputs. Logic 1 selects CLK1 and CLK1 inputs.
Differential Input (Positive) 0.
Differential Input (Negative) 0.
Reference Voltage. Reference voltage for biasing ac-coupled CLK0 and CLK0 inputs.
Center Tap. Center tap of a 100 Ω input resistor for CLK0 and CLK0 inputs.
Differential Input (Positive) 1.
Differential Input (Negative) 1.
Center Tap. Center tap of a 100 Ω input resistor for CLK1 and CLK1 inputs.
Reference Voltage. Reference voltage for biasing ac-coupled CLK1 and CLK1 inputs.
Negative Supply Pin.
Positive Supply Pin.
Q9, Q9
Q8, Q8
Q7, Q7
Q6, Q6
NC
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
No Connection
Q5, Q5
Q4, Q4
Q3, Q3
Q2, Q2
Q1, Q1
Q0, Q0
EPAD
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
Differential LVPECL Outputs.
EPAD must be connected to VEE.
Rev. 0 | Page 6 of 12
ADCLK950
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 3.3 V, VEE = 0 V, VICM = VREFx, TA = 25°C, clock outputs terminated at 50 Ω to VCC − 2 V, unless otherwise noted.
C4
C3
C4
C3
C4
500ps/DIV
100mV/DIV
08279-006
C3
08279-003
100mV/DIV
100ps/DIV
Figure 6. LVPECL Output Waveform @ 1000 MHz
Figure 3. LVPECL Output Waveform @ 200 MHz
1.8
214
213
1.6
1.5
PROPAGATION DELAY (ps)
DIFFERENTIAL OUTPUT VOLTAGE (V)
1.7
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
212
211
210
209
208
0.6
0
1000
2000
3000
4000
5000
FREQUENCY (MHz)
207
–40
08279-004
0.4
–20
0
20
40
60
08279-007
0.5
80
TEMPERATURE (°C)
Figure 4. Differential Output Voltage vs. Frequency, VID > 1.1 V p-p
Figure 7. Propagation Delay vs. Temperature, VID = 1.6 V p-p
225
230
PROPAGATION DELAY (ps)
215
210
205
200
195
190
220
+85°C
210
+25°C
200
–40°C
180
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
DIFFERENTIAL INPUT VOLTAGE SWING (V)
1.8
190
0.9
1.1
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
DC COMMON-MODE VOLTAGE (V)
Figure 5. Propagation Delay vs. Differential Input Voltage
Figure 8. Propagation Delay vs. DC Common-Mode Voltage vs.
Temperature, Input Slew Rate > 25 V/ns
Rev. 0 | Page 7 of 12
08279-008
185
08279-005
PROPAGATION DELAY (ps)
220
ADCLK950
–90
ABSOLUTE PHASE NOISE MEASURED @ 1GHz WITH AGILENT
E5052 USING WENZEL CLOCK SOURCE CONSISTING OF A
WENZEL 100MHz CRYSTAL OSCILLATOR (P/N 500-06672),
WENZEL 5× MULTIPLIER (P/N LNOM-100-5-13-14-F-A), AND A
WENZEL 2× MULTIPLIER (P/N LNDD-500-14-14-1-D).
–100
–40°C
PHASE NOISE (dBc/Hz)
1.52
+25°C
1.50
+85°C
1.48
1.46
–110
–120
–130
ADCLK950
–140
–150
1.44
–160
1.42
2.75
–170
10
2.85
2.95
3.05
3.15
3.25
3.35
3.45
3.55
3.65
3.75
POWER SUPPLY (V)
CLOCK SOURCE
100
1k
10k
100k
1M
10M
100M
FREQUENCY OFFSET (Hz)
Figure 9. Differential Output Voltage Swing vs. Power Supply Voltage vs.
Temperature, VID = 1.6 V p-p
08279-011
1.54
08279-009
DIFFERENTIAL OUTPUT VOLTAGE SWING (V)
1.56
Figure 11. Absolute Phase Noise Measured @1 GHz
300
400
ICC
250
RANDOM JITTER (fS rms)
300
250
+85°C
+25°C
–40°C
200
150
IEE
3.25
SUPPLY VOLTAGE (V)
3.50
3.75
100
0
08279-010
3.00
150
50
100
50
2.75
200
0
5
10
15
20
25
INPUT SLEW RATE (V/ns)
Figure 10. Power Supply Current vs. Power Supply Voltage vs. Temperature,
All Outputs Loaded (50 Ω to VCC − 2 V)
Rev. 0 | Page 8 of 12
Figure 12. RMS Random Jitter vs. Input Slew Rate, VID Method
08279-012
SUPPLY CURRENT (mA)
350
ADCLK950
FUNCTIONAL DESCRIPTION
Output jitter performance is degraded by an input slew rate
below 4 V/ns, as shown in Figure 12. The ADCLK950 is
specifically designed to minimize added random jitter over a
wide input slew rate range. Whenever possible, clamp excessively
large input signals with fast Schottky diodes because attenuators
reduce the slew rate. Input signal runs of more than a few
centimeters should be over low loss dielectrics or cables with
good high frequency characteristics.
LVPECL Y-termination is an elegant termination scheme that
uses the fewest components and offers both odd- and even-mode
impedance matching. Even-mode impedance matching is an
important consideration for closely coupled transmission lines
at high frequencies. Its main drawback is that it offers limited
flexibility for varying the drive strength of the emitter follower
LVPECL driver. This can be an important consideration when
driving long trace lengths but is usually not an issue.
VS_DRV
ADCLK950
CLOCK OUTPUTS
VS = VS_DRV
Z0 = 50Ω
The specified performance necessitates using proper transmission
line terminations. The LVPECL outputs of the ADCLK950 are
designed to directly drive 800 mV into a 50 Ω cable or into
microstrip/stripline transmission lines terminated with 50 Ω
referenced to VCC − 2 V, as shown in Figure 14. The LVPECL
output stage is shown in Figure 13. The outputs are designed for
best transmission line matching. If high speed signals must be
routed more than a centimeter, either the microstrip or the
stripline technique is required to ensure proper transition times
and to prevent excessive output ringing and pulse width dependent propagation delay dispersion.
50Ω
VCC – 2V
50Ω
LVPECL
08279-014
The ADCLK950 accepts a differential clock input from one of
two inputs and distributes the selected clock to all 10 LVPECL
outputs. The maximum specified frequency is the point at which
the output voltage swing is 50% of the standard LVPECL swing
(see Figure 4). See the functional block diagram (Figure 1) and
the General Description section for more clock input details.
See Figure 19 through Figure 23 for various clock input
termination schemes.
Thevenin-equivalent termination uses a resistor network to
provide 50 Ω termination to a dc voltage that is below VOL of
the LVPECL driver. In this case, VS_DRV on the ADCLK950
should equal VS of the receiving buffer. Although the resistor
combination shown (in Figure 15) results in a dc bias point of
VS_DRV − 2 V, the actual common-mode voltage is VS_DRV −
1.3 V because there is additional current flowing from the
ADCLK950 LVPECL driver through the pull-down resistor.
Z0 = 50Ω
Figure 14. DC-Coupled, 3.3 V LVPECL
VS_DRV
VS_DRV
ADCLK950
50Ω
127Ω
127Ω
SINGLE-ENDED
(NOT COUPLED)
VS
LVPECL
50Ω
83Ω
83Ω
08279-015
CLOCK INPUTS
VCC
Figure 15. DC-Coupled, 3.3 V LVPECL Far-End Thevenin Termination
ADCLK950
VS = VS_DRV
Z0 = 50Ω
50Ω
Qx
50Ω
50Ω
LVPECL
08279-016
VS_DRV
Z0 = 50Ω
Qx
VEE
08279-013
Figure 16. DC-Coupled, 3.3 V LVPECL Y-Termination
VS_DRV
ADCLK950
VS
0.1nF
Figure 13. Simplified Schematic Diagram of the LVPECL Output Stage
100Ω DIFFERENTIAL
100Ω
(COUPLED)
0.1nF TRANSMISSION LINE
200Ω
LVPECL
200Ω
Figure 17. AC-Coupled, LVPECL with Parallel Transmission Line
Rev. 0 | Page 9 of 12
08279-017
Figure 14 through Figure 17 depict various LVPECL output
termination schemes. When dc-coupled, VS of the receiving buffer
should match VS_DRV.
ADCLK950
A Logic 0 on the IN_SEL pin selects the Input CLK0 and
Input CLK0. A Logic 1 on the IN_SEL pin selects Input CLK1
and Input CLK1.
PCB LAYOUT CONSIDERATIONS
The ADCLK950 buffer is designed for very high speed applications. Consequently, high speed design techniques must be used
to achieve the specified performance. It is critically important
to use low impedance supply planes for both the negative supply
(VEE) and the positive supply (VCC) planes as part of a multilayer
board. Providing the lowest inductance return path for switching
currents ensures the best possible performance in the target
application.
The following references to the GND plane assume that the VEE
power plane is grounded for LVPECL operation. Note that for
ECL operation, the VCC power plane becomes the ground plane.
It is also important to adequately bypass the input and output
supplies. Place a 1 μF electrolytic bypass capacitor within several
inches of each VCC power supply pin to the GND plane. In
addition, place multiple high quality 0.001 μF bypass capacitors
as close as possible to each of the VCC supply pins, and connect
the capacitors to the GND plane with redundant vias. Carefully
select high frequency bypass capacitors for minimum inductance and ESR. To improve the effectiveness of the bypass at
high frequencies, minimize parasitic layout inductance. Also,
avoid discontinuities along input and output transmission lines
that can affect jitter performance.
return path. If the inputs are dc-coupled to a source, take care to
ensure that the pins are within the rated input differential and
common-mode ranges.
If the return is floated, the device exhibits a 100 Ω cross termination, but the source must then control the common-mode
voltage and supply the input bias currents.
There are ESD/clamp diodes between the input pins to prevent
the application from developing excessive offsets to the input
transistors. ESD diodes are not optimized for best ac performance. When a clamp is required, it is recommended that
appropriate external diodes be used.
Exposed Metal Paddle
The exposed metal paddle on the ADCLK950 package is both
an electrical connection and a thermal enhancement. For the
device to function properly, the paddle must be properly
attached to the VEE power plane.
When properly mounted, the ADCLK950 also dissipates heat
through its exposed paddle. The PCB acts as a heat sink for the
ADCLK950. The PCB attachment must provide a good thermal
path to a larger heat dissipation area. This requires a grid of vias
from the top layer down to the VEE power plane (see Figure 18).
The ADCLK950 evaluation board (ADCLK950/PCBZ) provides an example of how to attach the part to the PCB.
In a 50 Ω environment, input and output matching have a
significant impact on performance. The buffer provides internal
50 Ω termination resistors for both CLKx and CLKx inputs.
Normally, the return side is connected to the reference pin that is
provided. Carefully bypass the termination potential using
ceramic capacitors to prevent undesired aberrations on the
input signal due to parasitic inductance in the termination
Rev. 0 | Page 10 of 12
VIAS TO VEE POWER
PLANE
08279-018
CLOCK INPUT SELECT (IN_SEL) SETTINGS
Figure 18. PCB Land for Attaching Exposed Paddle
ADCLK950
INPUT TERMINATION OPTIONS
VREF x
VREF x
V Tx
VTx
50Ω
CLKx
50Ω
50Ω
CLKx
CLKx
50Ω
CLKx
ADCLK950
08279-019
ADCLK950
CONNECT VTx TO VCC.
08279-021
VCC
CONNECT VTx TO VREF x.
Figure 19. DC-Coupled CML Input Termination
Figure 21. AC-Coupled Input Termination, Such as LVDS and LVPECL
VREF x
V Tx
VCC
50Ω
CLKx
CLKx
50Ω
ADCLK950
CONNECT VTx, VREF x, AND CLKx. PLACE A
BYPASS CAPACITOR FROM VTx TO GROUND.
ALTERNATIVELY, VTx, VREF x, AND CLKx CAN BE
CONNECTED, GIVING A CLEANER LAYOUT AND
A 180º PHASE SHIFT.
ADCLK950
08279-020
CLKx
Figure 20. DC-Coupled LVPECL Input Termination
08279-022
50Ω
V Tx
50Ω
Figure 22. AC-Coupled Single-Ended Input Termination
VREF x
V Tx
50Ω
CLKx
50Ω
CLKx
ADCLK950
08279-023
0.01µF
(OPTIONAL)
50Ω
CLKx
VREF x
Figure 23. DC-Coupled 3.3 V CMOS Input Termination
Rev. 0 | Page 11 of 12
ADCLK950
OUTLINE DIMENSIONS
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
5.75
BSC SQ
0.50
BSC
20
19
PIN 1
INDICATOR
3.05
2.90 SQ
2.75
11
10
0.25 MIN
0.80 MAX
0.65 TYP
0.30
0.23
0.18
4.50
REF
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
082708-A
SEATING
PLANE
1
BOTTOM VIEW
TOP VIEW
12° MAX
40
EXPOSED
PAD
0.50
0.40
0.30
1.00
0.85
0.80
29
28
Figure 24. 40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
6 mm × 6 mm Body, Very Thin Quad
(CP-40-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADCLK950BCPZ 1
ADCLK950BCPZ-REEL71
ADCLK950/PCBZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
Evaluation Board
Z = RoHS Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08279-0-7/09(0)
Rev. 0 | Page 12 of 12
Package Option
CP-40-8
CP-40-8