AD ADV7190

a
Video Encoder with Six 10-Bit DACs and
Video Encoder with Six DAC Outputs
ADV7190/ADV7191*
FEATURES
Six High-Quality 10-Bit Video DACs
Multistandard Video Input
Multistandard Video Output
4ⴛ Oversampling with Internal 54 MHz PLL
Programmable Video Control Includes:
Digital Noise Reduction
Gamma Correction
LUMA Delay
CHROMA Delay
Multiple Luma and Chroma Filters
Luma SSAF™ (Super Subalias Filter)
Average Brightness Detection
Field Counter
Macrovision Rev 7.1
CGMS (Copy Generation Management System)
WSS (Wide Screen Signaling)
Closed Captioning Support
Teletext Insertion Port (PAL-WST)
2-Wire Serial MPU Interface
Supply Voltage 5 V and 3.3 V Operation
64-Lead LQFP Package
APPLICATIONS
DVD Playback Systems,
PC Video/Multimedia Playback Systems
GENERAL DESCRIPTION
The ADV7190/ADV7191 is part of the new generation of video
encoders from Analog Devices. The device builds on the performance of previous video encoders and provides new features such
as, Digital Noise Reduction, Gamma Correction, 4× Oversampling and 54 MHz operation, Average Brightness Detection,
Chroma Delay, an additional Chroma Filter, etc.
The ADV7190/ADV7191 supports NTSC-M, NTSC-N (Japan),
PAL N, PAL M, PAL-B/D/G/H/I and PAL-60 standards. Input
standards supported include ITU-R.BT656/601 4:2:2 YCrCb
in 8- or 16-bit format.
The ADV7190/ADV7191 can output Composite Video (CVBS),
S-Video (Y/C), Component YUV** or RGB. The analog
component output is also compatible with Betacam, MII
and SMPTE/EBU N10 levels, SMPTE 170M NTSC and
ITU-R.BT 470 PAL.
For more information about the ADV7190/ADV7191’s features refer to Detailed Description.
SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM
DIGITAL
INPUT
27MHz
CLOCK
VIDEO
INPUT
PROCESSING
8-BIT YCrCb
IN 4:2:2 FORMAT
ANALOG
OUTPUT
PLL
AND
54MHz
CHROMA
LPF
DEMUX
ITU–R.BT
656/601
VIDEO
OUTPUT
PROCESSING
VIDEO
SIGNAL
PROCESSING
AND
YCrCb–
TO–
YUV
MATRIX
COLOR CONTROL
DNR
GAMMA
CORRECTION
VBI
TELETEXT
CLOSED CAPTION
CGMS/WSS
MACROVISION
10-BIT
DAC
2ⴛ
OVERSAMPLING
SSAF
LPF
LUMA
LPF
OR
4ⴛ
OVERSAMPLING
10-BIT
DAC
10-BIT
DAC
10-BIT
DAC
COMPOSITE VIDEO
Y [S-VIDEO]
C [S-VIDEO]
RGB
YUV
TVSCREEN
10-BIT
DAC
10-BIT
DAC
I2C INTERFACE
ADV7190/ADV7191
*This device is protected by U.S. Patent Numbers 4631603, 4577216, and 4819098, and other intellectual property rights.
**Throughout the document YUV refers to digital or analog component video.
The Macrovision anticopy process is licensed for noncommercial home use only, which is its sole intended use in the device. Please contact sales office for latest available Macrovision version.
ITU-R and CCIR are used interchangeably in this document (ITU-R has replaced CCIR recommendations).
SSAF is a trademark of Analog Devices Inc.
I2C is a registered trademark of Philips Corporation.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
ADV7190/ADV7191
CONTENTS
VIDEO TIMING DESCRIPTION . . . . . . . . . . . . . . . . . . .
RESET SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MPU PORT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . .
REGISTER ACCESSES . . . . . . . . . . . . . . . . . . . . . . . . . . .
REGISTER PROGRAMMING . . . . . . . . . . . . . . . . . . . . .
MODE REGISTER 0–9 . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIMING REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUBCARRIER FREQUENCY AND
PHASE REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLOSED CAPTIONING REGISTERS . . . . . . . . . . . . . . .
NTSC PEDESTAL REGISTERS . . . . . . . . . . . . . . . . . . . .
TELETEXT CONTROL REGISTER . . . . . . . . . . . . . . . .
CGMS_WSS REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . .
CONTRAST, U SCALE AND V SCALE REGISTERS . .
HUE ADJUST, BRIGHTNESS CONTROL,
SHARPNESS CONTROL REGISTERS . . . . . . . . . . . .
GAMMA CORRECTION REGISTERS . . . . . . . . . . . . . .
BRIGHTNESS DETECT REGISTER . . . . . . . . . . . . . . . .
OUTPUT CLOCK REGISTER . . . . . . . . . . . . . . . . . . . . .
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM . . . . . . 1
SPECIFICATIONS
Static Performance 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Static Performance 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dynamic Specification 5 V . . . . . . . . . . . . . . . . . . . . . . . . . 5
Dynamic Specification 3.3 V . . . . . . . . . . . . . . . . . . . . . . . 5
Timing Characteristics 5 V . . . . . . . . . . . . . . . . . . . . . . . . 6
Timing Characteristics 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . 7
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 9
PACKAGE THERMAL PERFORMANCE . . . . . . . . . . . . . 9
PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . 10
DETAILED DESCRIPTION OF FEATURES . . . . . . . . . 11
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 11
DETAILED FUNCTIONAL BLOCK DIAGRAM . . . . . . 11
DATA PATH DESCRIPTION . . . . . . . . . . . . . . . . . . . . . 12
INTERNAL FILTER RESPONSE.. . . . . . . . . . . . . . . . . . . 13
FEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17
BRIGHTNESS DETECT . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CHROMA/LUMA DELAY . . . . . . . . . . . . . . . . . . . . . . . . 17
CLAMP OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CSO, HSO AND VSO OUTPUTS . . . . . . . . . . . . . . . . . . . 17
COLOR BAR GENERATION . . . . . . . . . . . . . . . . . . . . . . 17
COLOR BURST SIGNAL CONTROL . . . . . . . . . . . . . . . 17
COLOR CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CHROMINANCE CONTROL . . . . . . . . . . . . . . . . . . . . . 17
UNDERSHOOT LIMITER . . . . . . . . . . . . . . . . . . . . . . . . 17
DIGITAL NOISE REDUCTION . . . . . . . . . . . . . . . . . . . . 17
DOUBLE BUFFERING . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
GAMMA CORRECTION CONTROL . . . . . . . . . . . . . . . 18
NTSC PEDESTAL CONTROL . . . . . . . . . . . . . . . . . . . . . 18
POWER-ON RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
REAL-TIME CONTROL, SUBCARRIER RESET,
AND TIMING RESET . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SCH PHASE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SLEEP MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SQUARE PIXEL MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VERTICAL BLANKING DATA INSERTION AND
BLANK INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
YUV LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16-BIT INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4× OVERSAMPLING AND INTERNAL PLL . . . . . . . . . 19
APPENDIX 1
Board Design and Layout Considerations . . . . . . . . . . . .
APPENDIX 2
Closed Captioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 3
CGMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 4
WSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 5
Teletext Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 6
Optional Output Filter. . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 7
DAC Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 8
Recommended Register Values . . . . . . . . . . . . . . . . . . . .
APPENDIX 9
NTSC Waveforms (With Pedestal) . . . . . . . . . . . . . . . . .
NTSC Waveforms (Without Pedestal) . . . . . . . . . . . . . . .
PAL Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UV Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video Measurement Plots . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX 10
Vector Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . .
–2–
19
20
27
28
28
29
35
36
36
37
37
37
38
39
42
43
43
44
46
47
47
49
50
51
52
56
57
58
59
60
64
68
69
REV. 0
SPECIFICATIONS (V
5 V SPECIFICATIONS1
ADV7190/ADV7191
= 5 V, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All specifications TMIN to TMAX2
unless otherwise noted.)
AA
Parameter
Min
Typ
STATIC PERFORMANCE
Resolution (Each DAC)
Accuracy (Each DAC)
Integral Nonlinearity3
Differential Nonlinearity3
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN
Input Leakage Current
DIGITAL OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Three-State Leakage Current
Three-State Output Capacitance
ANALOG OUTPUTS
Output Current (Max)
Output Current (Min)
DAC-to-DAC Matching3
Output Compliance, VOC
Output Impedance, ROUT
Output Capacitance, COUT
VOLTAGE REFERENCE
Reference Range, VREF
Max
Unit
10
Bits
± 1.0
± 1.0
LSB
LSB
0.8
±1
10
V
V
µA
pF
µA
2
0
6
1
2.4
4.125
0.8
10
6
0.4
4.33
2.16
0.4
4.625
10
2.5
1.4
0
100
6
RL = 300 Ω, RSET1,2 = 1200 Ω
RL = 600 Ω, RSET1,2 = 2400 Ω
1.359
V
4.75
5.0
5.25
V
29
80
120
6
35
120
170
10
mA
mA
mA
mA
µA
µA
Specifications subject to change without notice.
REV. 0
mA
mA
%
V
kΩ
pF
1.235
NOTES
1
All measurements are made in 4× Oversampling Mode unless otherwise specified.
2
Temperature range T MIN to TMAX: 0°C to 70°C.
3
Guaranteed by characterization.
4
Measurement made in 2× oversampling mode.
5
IDAC is the total current required to supply all DACs including the V REF circuitry.
6
All six DACs ON.
7
ICCT, or the circuit current, is the continuous current required to drive the digital core without I PLL.
–3–
VIN = 0.4 V or 2.4 V
ISOURCE = 400 µA
ISINK = 3.2 mA
1.112
0.01
85
Guaranteed Monotonic
V
V
µA
pF
4
POWER REQUIREMENTS
VAA
Normal Power Mode
IDAC5
ICCT (2× Oversampling)6, 7
ICCT (4× Oversampling)6, 7
IPLL
Sleep Mode
IDAC
ICCT
Test Conditions
IOUT = 0 mA
ADV7190/ADV7191–SPECIFICATIONS
2
1 (VAA = 3.3 V, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All specifications TMIN to TMAX
3.3 V SPECIFICATIONS
unless otherwise noted.)
Parameter
Min
Typ
STATIC PERFORMANCE
Resolution (Each DAC)
Accuracy (Each DAC)
Integral Nonlinearity
Differential Nonlinearity
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN
Input Leakage Current
VOLTAGE REFERENCE
Reference Range, VREF
Unit
10
Bits
± 1.0
± 1.0
LSB
LSB
±1
10
V
V
µA
pF
µA
2
0.8
6
1
DIGITAL OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Three-State Leakage Current
Three-State Output Capacitance
ANALOG OUTPUTS
Output Current (Max)
Output Current (Min)
DAC-to-DAC Matching
Output Compliance, VOC
Output Impedance, ROUT
Output Capacitance, COUT
Max
2.4
0.4
10
6
4.25
10
4.33
2.16
0.4
4.625
1.4
100
6
30
Test Conditions
Guaranteed Monotonic
VIN = 0.4 V or 2.4 V
V
V
µA
pF
ISOURCE = 400 µA
ISINK = 3.2 mA
mA
mA
%
V
kΩ
pF
RSET1,2 = 1200 Ω, RL = 300 Ω
RL = 600 Ω, RSET1,2 = 2400 Ω
V
IVREFOUT = 20 µA
IOUT = 0 mA
3
POWER REQUIREMENTS
VAA
Normal Power Mode
IDAC4
ICCT (2× Oversampling)5, 6
ICCT (4× Oversampling)5, 6
IPLL
Sleep Mode
IDAC
ICCT
1.235
3.15
3.3
3.45
V
29
42
68
6
54
86
mA
mA
mA
mA
µA
µA
0.01
85
NOTES
1
All measurements are made in 4× Oversampling Mode unless otherwise specified and are guaranteed by characterization. In 2 × Oversampling Mode, the power requirement for the ADV7190/ADV7191 are typically 3.0 V.
2
Temperature range T MIN to TMAX: 0°C to 70°C.
3
Measurement made in 2× oversampling mode.
4
IDAC is the total current required to supply all DACs including the V REF circuitry.
5
All six DACs ON.
6
ICCT, or the circuit current, is the continuous current required to drive the digital core without I PLL.
Specifications subject to change without notice.
–4–
REV. 0
ADV7190/ADV7191
5 V DYNAMIC–SPECIFICATIONS1
Parameter
(VAA = 5 V ⴞ 250 mV, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All
specifications TMIN to TMAX2 unless otherwise noted.)
Min
3
Differential Gain
Differential Phase3
SNR (Pedestal)3
SNR (Ramp)3
Typ
Max
Unit
0.1 (0.4)
0.4 (0.15)
78.5 (78)
78 (78)
0.3 (0.5)
0.5 (0.3)
%
Degrees
dB rms
dB p-p
dB rms
dB p-p
Degrees
%
±%
± Degrees
±%
±%
ns
±%
dB
dB
61.7 (61.7)
62 (63)
Hue Accuracy
Color Saturation Accuracy
Chroma Nonlinear Gain
Chroma Nonlinear Phase
Chroma/Luma Intermod
Chroma/Luma Gain Ineq
Chroma/Luma Delay Ineq
Luminance Nonlinearity
Chroma AM Noise
Chroma PM Noise
0.5
0.7
0.7
0.5
0.1
1.7
2.2
0.6
82
72
0.9
0.7
Test Conditions
RMS
Peak Periodic
RMS
Peak Periodic
Referenced to 40 IRE
NOTES
1
All measurements are made in 4× Oversampling Mode unless otherwise specified.
2
Temperature range T MIN to TMAX: 0°C to 70°C.
3
Values in parentheses apply to 2× Oversampling Mode.
Specifications subject to change without notice.
(VAA = 3.3 V ⴞ 150 mV, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All
2
MIN to TMAX unless otherwise noted.)
3.3 V DYNAMIC–SPECIFICATIONS1 specifications T
Parameter
Min
Differential Gain3
Differential Phase3
SNR (Pedestal)3
SNR (Ramp)3
Hue Accuracy
Color Saturation Accuracy
Chroma Nonlinear Gain
Chroma Nonlinear Phase
Chroma/Luma Intermod
Luminance Nonlinearity
Chroma AM Noise
Chroma PM Noise
Typ
Max
0.2 (0.5)
0.5 (0.2)
78.5 (78)
78 (78)
62.3 (62)
61 (62.5)
0.5
0.8
0.6
0.5
0.1
0.6
83
71
NOTES
1
All measurements are made in 4× Oversampling Mode unless otherwise specified.
2
Temperature range T MIN to TMAX: 0°C to 70°C.
3
Values in parentheses apply to 2× Oversample Mode.
Specifications subject to change without notice.
REV. 0
–5–
Unit
%
Degrees
dB rms
dB p-p
dB rms
dB p-p
Degrees
%
±%
± Degrees
±%
±%
dB
dB
Test Conditions
RMS
Peak Periodic
RMS
Peak Periodic
Referenced to 40 IRE
ADV7190/ADV7191
(VAA = 5 V ⴞ 250 mV, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All specifications
1
MIN to TMAX unless otherwise noted.)
5 V TIMING CHARACTERISTICS T
Parameter
Min
Typ
Max
Unit
400
kHz
µs
µs
µs
µs
ns
ns
ns
µs
Test Conditions
2
MPU PORT
SCLOCK Frequency
SCLOCK High Pulsewidth, t1
SCLOCK Low Pulsewidth, t2
Hold Time (Start Condition), t3
Setup Time (Start Condition), t4
Data Setup Time, t5
SDATA, SCLOCK Rise Time, t6
SDATA, SCLOCK Fall Time, t7
Setup Time (Stop Condition), t8
0
0.6
1.3
0.6
0.6
100
300
300
0.6
After This Period the First Clock Is Generated
Relevant for Repeated Start Condition
2
ANALOG OUTPUTS
Analog Output Delay
DAC Analog Output Skew
8
0.1
ns
ns
27
13
12
57
67
MHz
ns
ns
ns
ns
ns
ns
ns
ns
Clock Cycles
Clock Cycles
TELETEXT PORT4
Digital Output Access Time, t16
Data Setup Time, t17
Data Hold Time, t18
11
3
6
ns
ns
ns
RESET CONTROL
RESET Low Time
3
CLOCK CONTROL AND PIXEL
PORT3
fCLOCK
Clock High Time, t9
Clock Low Time, t10
Data Setup Time, t11
Data Hold Time, t12
Control Setup Time, t11
Control Hold Time, t12
Digital Output Access Time, t13
Digital Output Hold Time, t14
Pipeline Delay, t15 (2× Oversampling)
Pipeline Delay, t15 (4× Oversampling)
8
8
6
5
6
4
20
ns
2
PLL
PLL Output Frequency
54
MHz
NOTES
1
Temperature range T MIN to TMAX: 0°C to 70°C.
2
Guaranteed by characterization.
3
Pixel Port consists of:
Data: P15–P0 Pixel Inputs,
Control: HSYNC, VSYNC, BLANK,
Clock: CLKIN Input.
4
Teletext Port consists of:
Digital Output: TTXRQ,
Data: TTX.
Specifications subject to change without notice.
–6–
REV. 0
ADV7190/ADV7191
3.3 V TIMING CHARACTERISTICS
Parameter
Max
Unit
400
2
kHz
µs
µs
µs
µs
ns
ns
ns
µs
8
0.1
ns
ns
27
13
12
57
67
MHz
ns
ns
ns
ns
ns
ns
ns
ns
Clock Cycles
Clock Cycles
TELETEXT PORT4
Digital Output Access Time, t16
Data Setup Time, t17
Data Hold Time, t18
11
3
6
ns
ns
ns
RESET CONTROL
RESET Low Time
3
PLL
PLL Output Frequency
54
MPU PORT
SCLOCK Frequency
SCLOCK High Pulsewidth, t1
SCLOCK Low Pulsewidth, t2
Hold Time (Start Condition), t3
Setup Time (Start Condition), t4
Data Setup Time, t5
SDATA, SCLOCK Rise Time, t6
SDATA, SCLOCK Fall Time, t7
Setup Time (Stop Condition), t8
Min
(VAA = 3.3 V ⴞ 150 mV, VREF = 1.235 V, RSET1,2 = 1200 ⍀ unless otherwise noted. All
specifications TMIN to TMAX1 unless otherwise noted2.)
0
0.6
1.3
0.6
0.6
100
300
300
0.6
ANALOG OUTPUTS
Analog Output Delay
DAC Analog Output Skew
CLOCK CONTROL AND PIXEL
PORT3
fCLOCK
Clock High Time, t9
Clock Low Time, t10
Data Setup Time, t11
Data Hold Time, t12
Control Setup Time, t11
Control Hold Time, t12
Digital Output Access Time, t13
Digital Output Hold Time, t14
Pipeline Delay, t15 (2× Oversampling)
Pipeline Delay, t15 (4× Oversampling)
Typ
8
8
6
4
2.5
3
20
ns
MHz
NOTES
1
Temperature range T MIN to TMAX: 0°C to 70°C.
2
Guaranteed by characterization.
3
Pixel Port consists of:
Data: P15–P0 Pixel Inputs,
Control: HSYNC, VSYNC, BLANK,
Clock: CLKIN Input.
4
Teletext Port consists of:
Digital Output: TTXRQ,
Data: TTX.
Specifications subject to change without notice.
REV. 0
–7–
Test Conditions
After This Period the First Clock Is Generated
Relevant for Repeated Start Condition
ADV7190/ADV7191
t5
t3
t3
SDA
t6
t1
SCL
t2
t7
t4
t8
Figure 1. MPU Port Timing Diagram
CLOCK
t9
CONTROL
I/PS
PIXEL INPUT
DATA
CONTROL
O/PS
t12
t10
HSYNC,
VSYNC,
BLANK
Cb
Y
Cr
Y
t11
HSYNC,
VSYNC,
BLANK,
CSO_HSO,
VSO, CLAMP
Cb
Y
t13
t14
Figure 2. Pixel and Control Data Timing Diagram
TTXREQ
t16
CLOCK
t17
t18
TTX
4 CLOCK
CYCLES
4 CLOCK
CYCLES
4 CLOCK
CYCLES
3 CLOCK
CYCLES
4 CLOCK
CYCLES
Figure 3. Teletext Timing Diagram
–8–
REV. 0
ADV7190/ADV7191
ABSOLUTE MAXIMUM RATINGS 1
PACKAGE THERMAL PERFORMANCE
VAA to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage on Any Digital Input Pin . . . . GND – 0.5 V to VAA + 0.5 V
Storage Temperature (TS) . . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . 150°C
Body Temperature (Soldering, 10 secs) . . . . . . . . . . . . 220°C
Analog Outputs to GND2 . . . . . . . . . . . . GND – 0.5 to VAA
The 64-lead package is used for this device. The junction-toambient (θJA) thermal resistance in still air on a four-layer PCB
is 38°C/W.
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
2
Analog Output Short Circuit to any Power Supply or Common can be of an
indefinite duration.
To reduce power consumption when using this part the user
can run the part on a 3.3 V supply, turn off any unused DACs.
The user must at all times stay below the maximum junction
temperature of 110°C. The following equation shows how to
calculate this junction temperature:
Junction Temperature = (VAA × (IDAC + ICCT)) × θJA + 70°C TAMB
IDAC = 10 mA + (sum of the average currents consumed by
each powered-on DAC)
Average current consumed by each powered-on DAC =
(VREF × K )/RSET
VREF = 1.235 V
K = 4.2146
RESET
VSO/CLAMP
CSO_HSO
NC
PAL NTSC
AGND
VAA
NC
TTX
NC
NC
NC
NC
NC
AGND
VAA
PIN CONFIGURATION
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
48
RSET1
47
VREF
P2 3
46
COMP 1
P3 4
P4 5
45
P0
P1 2
PIN 1
IDENTIFIER
DAC A
DAC B
43 VAA
44
P5 6
ADV7190/ADV7191
LQFP
P6 7
P7 8
42
41
TOP VIEW
(Not to Scale)
P8 9
P9 10
AGND
DAC C
40
DAC D
AGND
38 VAA
39
P10 11
P11 12
P12 13
37
P13 14
35
DAC E
36
DAC F
COMP 2
34 RSET2
P14 15
P15 16
33
AGND
SCRESET/RTC/TR
NC = NO CONNECT
SCL
SDA
AGND
CLKIN
CLKOUT
VAA
AGND
VAA
BLANK
ALSB
TTXREQ
VSYNC
HSYNC
VAA
AGND
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
ADV7190KST
ADV7191KST
0°C to 70°C
0°C to 70°C
64-Lead Quad Flatpack
64-Lead Quad Flatpack
ST-64
ST-64
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADV7190/ADV7191 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
REV. 0
–9–
WARNING!
ESD SENSITIVE DEVICE
ADV7190/ADV7191
PIN FUNCTION DESCRIPTIONS
Pin
No.
Mnemonic
Input/
Output
1–16
P0–P15
I
17, 25, 29,
38, 43, 54,
63
18, 24, 26,
33, 39, 42,
55, 64
19
VAA
P
8-Bit or 16-Bit 4:2:2 Multiplexed YCrCb Pixel Port. The LSB of the input data is set up on
Pin P0.
Analog Power Supply (3.3 V to 5 V).
AGND
G
Analog Ground.
HSYNC
I/O
20
VSYNC
I/O
21
BLANK
I/O
22
23
27
ALSB
TTXREQ
CLKIN
I
O
I
28
30
31
32
O
I
I/O
I
34
CLKOUT
SCL
SDA
SCRESET/
RTC/TR
RSET2
35
36
37
40
41
44
45
46
47
COMP 2
DAC F
DAC E
DAC D
DAC C
DAC B
DAC A
COMP 1
VREF
O
O
O
O
O
O
O
O
I/O
48
RSET1
I
49
RESET
I
50
51
CSO_HSO
VSO/CLAMP
O
I/O
52
53, 57–62
56
PAL_NTSC
NC
TTX
I
HSYNC (Modes 1, 2, and 3) Control Signal. This pin may be configured to be an output
(Master Mode) or an input (Slave Mode) and accept Sync Signals.
VSYNC Control Signal. This pin may be configured as an output (Master Mode) or as an
input (Slave Mode) and accept VSYNC as a Control Signal.
Video Blanking Control Signal. This signal is optional. For further information see Vertical
Blanking and Data Insertion BLANK Input section.
TTL Address Input. This signal sets up the LSB of the MPU address.
Teletext Data Request Output Signal, used to control teletext data transfer.
TTL Clock Input. Requires a stable 27 MHz reference clock for standard operation. Alternatively, a 24.5454 MHz (NTSC) or 29.5 MHz (PAL) can be used for square pixel operation.
Clock Output Pin.
MPU Port Serial Interface Clock Input.
MPU Port Serial Data Input/Output.
Multifunctional Input: Real-Time Control (RTC) Input, Timing Reset Input, Subcarrier Reset
Input.
A 1200 Ω resistor connected from this pin to GND is used to control full-scale amplitudes
of the Video Signals from DACs D, E, and F.
Compensation Pin for DACs D, E, and F. Connect a 0.1 µF Capacitor from COMP2 to VAA.
S-Video C/V/RED Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video Y/U/BLUE Analog Output. This DAC is capable of providing 4.33 mA output.
Composite/Y/GREEN Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video C/V/RED Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video Y/U/BLUE Analog Output. This DAC is capable of providing 4.33 mA output.
Composite/Y/GREEN Analog Output. This DAC is capable of providing 4.33 mA output.
Compensation Pin for DACs A, B, and C. Connect a 0.1 µF Capacitor from COMP1 to VAA.
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V). An external
VREF cannot be used in 4× oversampling mode.
A 1200 Ω resistor connected from this pin to GND is used to control full-scale amplitudes
of the Video Signals from DACs A, B, and C.
The input resets the on-chip timing generator and sets the ADV7190/ADV7191 into default
mode. See Appendix 8 for Default Register settings.
Dual function CSO or HSO Output Sync Signal at TTL Level.
Multifunction Pin. VSO Output Sync Signal at TTL level. CLAMP TTL Output Signals
can be used to drive external circuitry to enable clamping of all Video Signals.
Input signal to select PAL or NTSC mode of operation, pin set to Logic 1 selects PAL.
No Connect.
Teletext Data Input Pin.
I
I
Function
–10–
REV. 0
ADV7190/ADV7191
DETAILED DESCRIPTION OF FEATURES
Clocking:
Single 27 MHz Clock Required to Run the Device
4ⴛ Oversampling with Internal 54 MHz PLL
Square Pixel Operation
Advanced Power Management
Programmable Video Control Features:
Digital Noise Reduction
Pedestal level
Hue, Brightness, Contrast and Saturation
Clamping Output Signal
VBI (Vertical Blanking Interval)
Subcarrier Frequency and Phase
LUMA Delay
CHROMA Delay
Gamma Correction
Luma and Chroma Filters
Luma SSAF (Super Subalias Filter)
Average Brightness Detection
Field Counter
Interlaced/Noninterlaced Operation
Complete On-Chip Video Timing Generator
Programmable Multimode Master/Slave Operation
CGMS (Copy Generation Management System)
WSS (Wide Screen Signaling)
Macrovision 7.1 Rev
Closed Captioning Support
Teletext Insertion Port (PAL-WST)
2-Wire Serial MPU Interface
I2C Registers Synchronized to VSYNC
Six DACs are available on the ADV7190/ADV7191, each of which
is capable of providing 4.33 mA of current. In addition to the
composite output signal there is the facility to output S-Video
(Y/C Video), RGB Video and YUV Video. All YUV formats
(Betacam, MII and (SMPTE/EBU N10) are supported.
Digital Noise Reduction allows improved picture quality in removing low amplitude, high frequency noise. The block diagram below
shows the DNR functionality in the two modes available.
DNR MODE
DNR CONTROL
NOISE SIGNAL PATH
FILTER OUTPUT
<THRESHOLD?
Y DATA
INPUT
FILTER OUTPUT>
THRESHOLD
MAIN SIGNAL PATH
HSYNC
VSYNC
BLANK
DNR CONTROL
INPUT FILTER
BLOCK
FILTER OUTPUT
>THRESHOLD?
Y DATA
INPUT
CSO_HSO
FILTER OUTPUT<
THRESHOLD
10
10
YCrCb Y
TO
10
YUV
U
MATRIX 10
DNR
Y
AND
10
GAMMA
U
10
CORRECTION
V
V
10 10 10
P0
BRIGHTNESS
CONTROL
AND
ADD SYNC
AND
INTERPOLATOR
SATURATION
CONTROL
AND
ADD BURST
AND
INTERPOLATOR
SDA ALSB
I2C MPU PORT
PROGRAMMABLE
LUMA FILTER
AND
SHARPNESS
FILTER
PROGRAMMABLE
CHROMA
FILTER
YUV-TO-RGB
MATRIX
AND
YUV LEVEL
CONTROL
BLOCK
MODULATOR
AND
HUE CONTROL
DEMUX
P15
CLKIN
PLL
ADV7190/ADV7191
REAL-TIME
CONTROL
CIRCUIT
SIN/COS
DDS
BLOCK
CLKOUT
SCRESET/RTC/TR
Figure 4. Detailed Functional Block Diagram
REV. 0
DNR OUT
Figure 5. Block Diagram for DNR Mode and DNR Sharpness
Mode
SCL
CGMS/WSS
AND
CLOSED CAPTIONING
CONTROL
TELETEXT
INSERTION
BLOCK
TTX
ADD SIGNAL ABOVE THRESHOLD
RANGE TO ORIGINAL SIGNAL
NOISE SIGNAL PATH
RESET
TTXRQ
GAIN
BLOCK SIZE CONTROL CORING GAIN DATA
BORDER AREA
CORING GAIN BORDER
BLOCK OFFSET
MAIN SIGNAL PATH
VIDEO TIMING
GENERATOR
DNR OUT
DNR SHARPNESS MODE
The ADV7190/ADV7191 is an integrated Digital Video Encoder
that converts digital CCIR-601/656 4:2:2 8-bit or 16-bit component video data into a standard analog baseband television
signal compatible with worldwide standards.
VSO/CLAMP
SUBTRACT SIGNAL IN THRESHOLD
RANGE FROM ORIGINAL SIGNAL
INPUT FILTER
BLOCK
GENERAL DESCRIPTION
PAL_NTSC
GAIN
BLOCK SIZE CONTROL CORING GAIN DATA
BORDER AREA
CORING GAIN BORDER
BLOCK OFFSET
–11–
M
U
L
T
I
P
L
E
X
E
R
I
N
T
E
R
P
O
L
A
T
O
R
I
N
T
E
R
P
O
L
A
T
O
R
10-BIT
DAC
DAC A
10-BIT
DAC
DAC B
10-BIT
DAC
DAC C
DAC
CONTROL
BLOCK
VREF
RSET2
COMP2
10-BIT
DAC
DAC D
10-BIT
DAC
DAC F
10-BIT
DAC
DAC E
DAC
CONTROL
BLOCK
RSET1
COMP1
ADV7190/ADV7191
Programmable gamma correction is also available. Figure 6 shows
the response of different gamma values to a ramp signal.
An advanced power management circuit enables optimal control
of power consumption in normal operating modes or sleep modes.
The Output Video Frames are synchronized with the incoming
data Timing Reference Codes. Optionally, the Encoder accepts
(and can generate) HSYNC, VSYNC, and FIELD timing signals.
These timing signals can be adjusted to change pulsewidth and
position while the part is in master mode.
300
GAMMA–CORRECTED AMPLITUDE
GAMMA CORRECTION BLOCK OUTPUT
TO A RAMP INPUT FOR VARIOUS GAMMA VALUES
250
SIGNAL OUTPUTS
200
HSO/CSO and VSO TTL outputs are also available and are timed
to the analog output video.
0.3
0.5
150
A separate teletext port enables the user to directly input teletext
data during the vertical blanking interval.
UT
NP
LI
A
1.5
GN
SI
100
The ADV7190/ADV7191 also incorporates WSS and CGMS-A
data control generation and Macrovision Rev 7.1.
1.8
50
0
0
50
100
150
LOCATION
200
The ADV7190/ADV7191 modes are set up over a 2-wire
serial bidirectional port (I2C-compatible) with two slave
addresses, and the device is register-compatible with the
ADV7172/ADV7173.
250
Figure 6. Signal Input (Ramp) and Selectable Gamma
Output Curves
The on-board SSAF (Super Subalias Filter) with extended
luminance frequency response and sharp stopband attenuation
enables studio quality video playback on modern TVs, giving
optimal horizontal line resolution. An additional sharpness
control feature allows high-frequency enhancement on the luminance signal.
The device is driven by a 27 MHz clock. Data can be output at
27 MHz or 54 MHz (on-board PLL) when 4⫻ oversampling is
enabled. Also, the output filter requirements in 4⫻ oversampling
and 2⫻ oversampling differ, as can be seen in Figure 7.
2ⴛ FILTER
REQUIREMENTS
0dB
4ⴛ FILTER
REQUIREMENTS
–30dB
6.75MHz
13.5MHz
27.0MHz
40.5MHz
54.0MHz
Figure 7. Output Filter Requirements in 4 × Oversampling
Mode
ADV7190/ADV7191
MPEG2
PIXEL BUS
27MHz
ENCODER
CORE
54MHz
PLL
2
ⴛ
I
N
T
E
R
P
O
L
A
T
I
O
N
6
D
A
C
O
U
T
P
U
T
S
54MHz
OUTPUT
RATE
Figure 8. PLL and 4 × Oversampling Block Diagram
The ADV7190/ADV7191 also supports both PAL and NTSC
square pixel operation. In this case the encoder requires a
24.5454 MHz Clock for NTSC or 29.5 MHz Clock for PAL
square pixel mode operation. All internal timing is generated
on-chip.
The ADV7190ADV7191 is packaged in a 64-lead LQFP
package.
DATA PATH DESCRIPTION
For PAL B, D, G, H, I, M, N, and NTSC M, N modes, YCrCb
4:2:2 Data is input via the CCIR-656/601-compatible Pixel
Port at a 27 MHz data rate. The pixel data is demultiplexed to
form three data paths. Y typically has a range of 16 to 235, Cr
and Cb typically have a range of 128+/–112; however, it is
possible to input data from 1 to 254 on both Y, Cb, and Cr.
The ADV7190/ADV7191 supports PAL (B, D, G, H, I, N, M)
and NTSC M, N (with and without Pedestal) and PAL60 standards. Digital Noise Reduction can be applied to the Y signal.
Programmable gamma correction can also be applied to the Y
signal if required.
The Y data can be manipulated for contrast control and a set-up
level can be added for brightness control. The Cr, Cb data can
be scaled to achieve color saturation control. All settings become
effective at the start of the next field when double buffering is
enabled.
The appropriate sync, blank, and burst levels are added to the
YCrCb data. Macrovision antitaping, (ADV7190 only) ClosedCaptioning, and Teletext levels are also added to Y and the
resultant data is interpolated to 54 MHz when 4× Oversampling
is enabled. The interpolated data is filtered and scaled by three
digital FIR filters.
The U and V signals are modulated by the appropriate Subcarrier
Sine/Cosine waveforms and a phase offset may be added onto
the color subcarrier during active video to allow hue adjustment.
The resulting U and V signals are added together to make up
the Chrominance Signal. The Luma (Y) signal can be delayed
by up to six clock cycles (at 27 MHz) and the Chroma signal
can be delayed by up to eight clock cycles (at 27 MHz). The
Luma and Chroma Signals are added together to make up the
Composite Video Signal. All timing signals are controlled.
The YCrCb data is also used to generate RGB data with appropriate sync and blank levels. The YUV levels are scaled to output
the suitable SMPTE/EBU N10, MII, or Betacam levels.
–12–
REV. 0
ADV7190/ADV7191
Each DAC can be individually powered off if not required. A
complete description of DAC output configurations is given in
the MR2 Bit Description section.
In Extended Mode there is the option of twelve responses in
the range from –4 dB to +4 dB. The desired response can be
chosen by the user by programming the correct value via the
I2C. The variation of frequency responses can be seen on the
following pages. For more detailed plots refer to AN-562
Analog Devices’ Application note.
Video output levels are illustrated in Appendix 9.
INTERNAL FILTER RESPONSE
The Y Filter supports several different frequency responses
including two low-pass responses, two notch responses, an
Extended (SSAF) response with or without gain boost/attenuation,
a CIF response and a QCIF response. The UV Filter supports
several different frequency responses including five low-pass
responses, a CIF response and a QCIF response, as can be seen on
the following pages.
Table I. Luminance Internal Filter Specifications (4ⴛ Oversampling)
Filter Type
Low-Pass (NTSC)
Low-Pass (PAL)
Notch (NTSC)
Notch (PAL)
Extended (SSAF)
CIF
QCIF
Filter Selection
MR04
0
0
0
0
1
1
1
MR03
0
0
1
1
0
0
1
MR02
0
1
0
1
0
1
0
Passband
Ripple1 (dB)
3 dB Bandwidth2
(MHz)
Stopband
Cutoff 3 (MHz)
Stopband
Attentuation4 (dB)
0.16
0.1
0.09
0.1
0.04
0.127
Monotonic
4.24
4.81
2.3/4.9/6.6
3.1/5.6/6.4
6.45
3.02
1.5
6.05
6.41
8.03
8.02
8.03
5.09
3.74
–75.2
–64.6
–87.3
–79.7
–86.6
–62.6
–88.2
NOTES
1
Passband ripple is defined to be fluctuations from the 0 dB response in the passband, measured in (dB). The passband is defined to have 0-fc frequency limits for a
low-pass filter, 0–f1 and f2–infinity for a notch filter, where fc, f1, f2 are the –3 dB points.
2
3 dB bandwidth refers to the –3 dB cutoff frequency.
3
Stopband cutoff refers to the frequency at the attenuation point referred to under Note 4.
4
Stopband Attenuation refers to the attenuation point (dB) at the frequency referred to under Note 3.
Table II. Chrominance Internal Filter Specifications (4ⴛ Oversampling)
Filter Type
1.3 MHz Low-Pass
0.65 MHz Low-Pass
1.0 MHz Low-Pass
2.0 MHz Low-Pass
3.0 MHz Low-Pass
CIF
QCIF
Filter Selection
MR07
0
0
0
0
1
1
1
MR06
0
0
1
1
0
0
1
MR05
0
1
0
1
0
1
0
Passband
Ripple1 (dB)
3 dB Bandwidth2
(MHz)
Stopband
Cutoff 3 (MHz)
Stopband
Attentuation4 (dB)
0.09
Monotonic
Monotonic
0.048
Monotonic
Monotonic
Monotonic
1.395
0.65
1.0
2.2
3.2
0.65
0.5
2.46
2.41
1.89
3.1
5.3
2.41
1.75
–83.9
–71.1
–64.43
–65.9
–84.5
–71.1
–33.1
NOTES
1
Passband ripple is defined to be fluctuations from the 0 dB response in the passband, measured in (dB). The passband is defined to have 0-fc frequency limits for a
low-pass filter, 0–f1 and f2–infinity for a notch filter, where fc, f1, f2 are the –3 dB points.
2
3 dB bandwidth refers to the –3 dB cutoff frequency.
3
Stopband cutoff refers to the frequency at the attenuation point referred to under Note 4.
4
Stopband Attenuation refers to the attenuation point (dB) at the frequency referred to under Note 3.
REV. 0
–13–
0
0
–10
–10
–20
–20
MAGNITUDE – dB
MAGNITUDE – dB
ADV7190/ADV7191
–30
–40
–30
–40
–50
–50
–60
–60
–70
2
0
4
6
8
FREQUENCY – MHz
10
–70
12
0
0
–10
–10
–20
–20
–30
–40
–60
–60
4
6
8
FREQUENCY – MHz
10
10
12
–40
–50
2
6
8
FREQUENCY – MHz
–30
–50
0
4
Figure 12. NTSC Notch Luma Filter
MAGNITUDE – dB
MAGNITUDE – dB
Figure 9. NTSC Low-Pass Luma Filter
–70
2
0
–70
12
2
0
Figure 10. PAL Low-Pass Luma Filter
4
6
8
FREQUENCY – MHz
10
12
Figure 13. PAL Notch Luma Filter
5
0
4
–20
MAGNITUDE – dB
MAGNITUDE – dB
–10
–30
–40
3
2
1
–50
0
–60
–70
0
2
4
6
8
FREQUENCY – MHz
10
–1
12
Figure 11. Extended Mode (SSAF) Luma Filter
0
1
2
4
3
FREQUENCY – MHz
5
6
7
Figure 14. Extended SSAF and Programmable Gain,
Showing Range 0 dB/+4 dB Range
–14–
REV. 0
ADV7190/ADV7191
1
0
–10
–1
–20
MAGNITUDE – dB
MAGNITUDE – dB
0
–2
–3
–30
–40
–50
–4
–5
–60
0
1
4
3
FREQUENCY – MHz
2
5
6
–70
7
0
2
4
0
2
–10
0
–2
–4
–6
0
1
4
3
FREQUENCY – MHz
2
5
6
12
–30
–40
0
0
0
–10
–10
–20
–20
–30
–40
–60
–60
4
6
8
FREQUENCY – MHz
10
6
8
FREQUENCY – MHz
–40
–50
2
4
–30
–50
0
2
Figure 19. Chroma 0.65 MHz Low-Pass Filter
MAGNITUDE – dB
MAGNITUDE – dB
10
–20
–70
7
Figure 16. Extended SSAF and Programmable
Attenuation, Showing Range +4 dB/–12 dB
–70
12
Figure 17. Luma CIF Filter
REV. 0
12
–60
–10
–70
10
–50
–8
–12
6
8
FREQUENCY – MHz
Figure 18. QCIF Filter
MAGNITUDE – dB
MAGNITUDE – dB
Figure 15. Extended SSAF and Programmable
Attenuation, Showing Range 0 dB/–4 dB
4
0
2
4
6
8
FREQUENCY – MHz
10
Figure 20. Chroma 1.0 MHz Low-Pass Filter
–15–
12
0
0
–10
–10
–20
–20
MAGNITUDE – dB
MAGNITUDE – dB
ADV7190/ADV7191
–30
–40
–30
–40
–50
–50
–60
–60
–70
0
2
4
6
8
FREQUENCY – MHz
10
–70
12
0
0
0
–10
–10
–20
–20
–30
–40
–60
–60
2
4
6
8
FREQUENCY – MHz
10
10
12
10
12
–40
–50
0
6
8
FREQUENCY – MHz
–30
–50
–70
4
Figure 24. Chroma CIF Filter
MAGNITUDE – dB
MAGNITUDE – dB
Figure 21. Chroma 1.3 MHz Low-Pass Filter
2
–70
12
Figure 22. Chroma 2 MHz Low-Pass Filter
0
2
4
6
8
FREQUENCY – MHz
Figure 25. Chroma QCIF Filter
0
MAGNITUDE – dB
–10
–20
–30
–40
–50
–60
–70
0
2
4
6
8
FREQUENCY – MHz
10
12
Figure 23. Chroma 3 MHz Low-Pass Filter
–16–
REV. 0
ADV7190/ADV7191
FEATURES: FUNCTIONAL DESCRIPTION
COLOR BAR GENERATION
BRIGHTNESS DETECT
The ADV7190/ADV7191 can be configured to generate 100/
7.5/75/7.5 color bars for NTSC or 100/0/75/0 color bars for
PAL. (Mode Register 4.)
This feature is used to monitor the average brightness of the
incoming Y signal on a field-by-field basis. The information is
read from the I2C and based, on this information, the color
saturation, contrast and brightness controls can be adjusted (for
example to compensate for very dark pictures). (Brightness Detect
Register.)
COLOR BURST SIGNAL CONTROL
The burst information can be switched on and off the composite
and chroma video output. (Mode Register 4.)
CHROMA/LUMA DELAY
COLOR CONTROLS
The luminance data can be delayed by maximum of six clock
cycles. Additionally the Chroma can be delayed by a maximum
of eight clock cycles (one clock cycle at 27 MHz). (Timing
Register 0 and Mode Register 9.)
The ADV7190/ADV7191 allows the user to control the brightness,
contrast, hue, and saturation of the color. The control registers may be double-buffered, meaning that any modification to
the registers will be done outside the active video region and,
therefore, changes made will not be visible during active video.
Contrast Control
Contrast adjustment is achieved by scaling the Y input data by a
factor programmed by the user. This factor allows the data to be
scaled between 0% and 150%. (Contrast Control Register.)
LUMA DELAY
CHROMA DELAY
Brightness Control
The brightness is controlled by adding a programmable setup level
onto the scaled Y data.
Figure 26. Chroma Delay
Figure 27. Luma Delay
For NTSC with pedestal, the setup can vary from 0 IRE to
22.5 IRE. For NTSC without pedestal and PAL, the setup can
vary from –7.5 IRE to +15 IRE. (Brightness Control Register.)
Color Saturation
CLAMP OUTPUT
The ADV7190/ADV7191 has a programmable clamp TTL
output signal. This clamp signal is programmable to the front
and back porch. The clamp signal can be varied by one to
three clock cycles in a positive and negative direction from the
default position. (Mode Register 5, Mode Register 7.)
CLAMP O/P SIGNALS
CVBS
OUTPUT PIN
MR57 = 1
CLAMP
OUTPUT PIN
MR57 = 0
CSO, HSO AND VSO OUTPUTS
The ADV7190/ADV7191 supports three output timing signals, CSO (Composite Sync Signal), HSO (Horizontal Sync
Signal) and VSO (Vertical Sync Signal). These output TTL signals are aligned with the analog video outputs. See Figure 29 for
an example of these waveforms. (Mode Register 7.)
EXAMPLE:- NTSC
1
2
3
4
5
6
7
8
Hue Adjust Control
The hue adjustment is achieved on the composite and chroma
outputs by adding a phase offset onto the color subcarrier in the
active video but leaving the color burst unmodified, i.e., only
the phase between the video and the colorburst is modified and
hence the hue is shifted. The ADV7190/ADV7191 provides a
range of ± 22° in increments of 0.17578125°. (Hue Adjust
Register.)
CHROMINANCE CONTROL
The color information can be switched on and off the composite, chroma and color component video outputs. (Mode
Register 4.)
Figure 28. Clamp Output Timing
525
Color adjustment is achieved by scaling the Cr and Cb input
data by a factor programmed by the user. This factor allows the
data to be scaled between 0% and 200%. (U Scale Register and
V Scale Register.)
9
10
OUTPUT
VIDEO
11–19
UNDERSHOOT LIMITER
A limiter is placed after the digital filters. This prevents any
synchronization problems for TVs. The level of undershoot is
programmable between –1.5 IRE, –6 IRE, –11 IRE when operating in 4× Oversampling. In 2× Oversampling mode the limits are
–7.5 IRE and 0 IRE. (Mode Register 9 and Timing Register 0.)
DIGITAL NOISE REDUCTION
CSO
HSO
VSO
Figure 29. CSO, HSO, VSO Timing Diagram
DNR is applied to the Y data only. A filter block selects the
high frequency, low amplitude components of the incoming
signal (DNR Input Select). The absolute value of the filter output
is compared to a programmable threshold value (DNR Threshold Control).
Two DNR modes are available: DNR Mode and DNR Sharpness Mode.
REV. 0
–17–
ADV7190/ADV7191
In DNR Mode, if the absolute value of the filter output is smaller
than the threshold, it is assumed to be noise. A programmable
amount (Coring Gain Control) of this noise signal will be subtracted from the original signal.
In DNR Sharpness Mode, if the absolute value of the filter output
is less than the programmed threshold, it is assumed to be noise,
as before. Otherwise, if the level exceeds the threshold, now
being identified as a valid signal, a fraction of the signal (Coring
Gain Control) will be added to the original signal in order to boost
high frequency components and to sharpen the video image.
In MPEG systems it is common to process the video information
in blocks of 8 × 8 pixels for MPEG2 systems, or 16 × 16 pixels for
MPEG1 systems (Block Size Control). DNR can be applied to
the resulting block transition areas that are known to contain
noise. Generally the block transition area contains two pixels.
It is possible to define this area to contain four pixels (Border
Area Control).
It is also possible to compensate for variable block positioning or
differences in YCrCb pixel timing with the use of the (Block Offset
Control). See Figure 82 for further information (Mode Register
8, DNR Registers 0–2.)
(a) A TIMING RESET is achieved in holding this pin high. In
this state the horizontal and vertical counters will remain reset.
On releasing this pin (set to low), the internal counters will
commence counting again. The minimum time the pin has
to be held high is 37 ns (1 clock cycle at 27 MHz), otherwise
the reset signal might not be recognized.
(b) The SUBCARRIER PHASE will reset to that of Field 0 at
the start of the following field when a low-to-high transition
occurs on this input pin.
(c) In RTC MODE, the ADV7190/ADV7191 can be used to
lock to an external video source.
The real-time control mode allows the ADV7190/ADV7191
to automatically alter the subcarrier frequency to compensate for line length variations. When the part is connected to
a device that outputs a digital datastream in the RTC format
such as an ADV7185 video decoder (see Figure 32), the part
will automatically change to the compensated subcarrier
frequency on a line-by-line basis. This digital datastream is
67 bits wide and the subcarrier is contained in Bits 0 to 21.
Each bit is two clock cycles long. 00Hex should be written
into all four Subcarrier Frequency registers when using this
mode. (Mode Register 4.)
DOUBLE BUFFERING
Double buffering can be enabled or disabled on the following
registers: Closed Captioning Registers, Brightness Control,
V Scale, U Scale, Contrast Control, Hue Adjust, the Gamma
Curve Select bit, and Macrovision Registers. These registers are
updated once per field on the falling edge of the VSYNC signal.
Double buffering improves the overall performance of the
ADV7190/ADV7191, since modifications to register settings
will not be made during active video, but take effect on the
start of the active video. (Mode Register 8.)
GAMMA CORRECTION CONTROL
Gamma correction may be performed on the luma data. The
user has the choice to use either of two different gamma curves,
A or B. At any one time one of these curves is operational if
gamma correction is enabled. Gamma correction allows the
mapping of the luma data to a user-defined function. (See Gamma
Correction Registers 0–13 section.) (Mode Register 8, Gamma
Correction Registers 0–13.)
In NTSC mode it is possible to have the pedestal signal generated on the output video signal. (Mode Register 2.)
POWER-ON RESET
After power-up, it is necessary to execute a RESET operation. A
reset occurs on the falling edge of a high-to-low transition on the
RESET pin. This initializes the pixel port such that the data on
the pixel inputs pins is ignored. See Appendix 8 for the register
settings after RESET is applied.
Together with the SCRESET/RTC/TR pin and of Mode
Register 4 (Genlock Control), the ADV7190/ADV7191 can
be used in (a) Timing Reset Mode, (b) Subcarrier Phase
Reset Mode or (c) RTC Mode.
The SCH phase is configured in default mode to reset every
four (NTSC) or eight (PAL) fields to avoid an accumulation of
SCH phase error over time. In an ideal system, zero SCH phase
error would be maintained forever, but in reality, this is impossible to achieve due to clock frequency variations. This effect is
reduced by the use of a 32-bit DDS, which generates this SCH.
Resetting the SCH phase every four or eight fields avoids the
accumulation of SCH phase error, and results in very minor SCH
phase jumps at the start of the four or eight field sequence.
Automatically resetting the SCH phase should not be done if
the video source does not have stable timing or the ADV7190/
ADV7191 is configured in RTC mode. Under these conditions
(unstable video) the Subcarrier Phase Reset should be enabled but no reset applied. In this configuration the SCH
Phase will never be reset; this means that the output video will
now track the unstable input video.
The Subcarrier Phase Reset, when applied, will reset the SCH
phase to Field 0 at the start of the next field (e.g., Subcarrier
Phase Reset applied in Field 5 (PAL) on the start of the next
field SCH phase will be reset to Field 0). (Mode Register 4.)
NTSC PEDESTAL CONTROL
REAL-TIME CONTROL, SUBCARRIER RESET, AND
TIMING RESET
SCH PHASE MODE
SLEEP MODE
If, after RESET, the SCRESET/RTC/TR and NTSC_PAL pins
are both set high, the ADV7190/ADV7191 will power-up in
Sleep Mode to facilitate low power consumption before all
registers have been initialized. If Power-Up in Sleep Mode is
disabled, Sleep Mode control passes to the Sleep Mode control
in Mode Register 2 (i.e., control via I2C). (Mode Register 2
and Mode Register 6.)
SQUARE PIXEL MODE
The ADV7190/ADV7191 can be used to operate in square pixel
mode. For NTSC operation an input clock of 24.5454 MHz is
required. Alternatively, for PAL operation, an input clock of
29.5 MHz is required. The internal timing logic adjusts accordingly for square pixel mode operation. Square pixel mode
is not available in 4× Oversampling mode. (Mode Register 2.)
REV. 0
–18–
ADV7190/ADV7191
VERTICAL BLANKING DATA INSERTION AND BLANK
INPUT
It is possible to allow encoding of incoming YCbCr data on
those lines of VBI that do not have line sync or pre-/postequalization pulses (see Figures 34 to 45). This mode of operation
is called Partial Blanking. It allows the insertion of any VBI
data (Opened VBI) into the encoded output waveform. This data
is present in digitized incoming YCbCr data stream (e.g., WSS
data, CGMS, VPS etc.). Alternatively, the entire VBI may be
blanked (no VBI data inserted) on these lines. VBI is available
in all timing modes.
The ADV7190/ADV7191 is supplied with a 27 MHz clock synced
with the incoming data. Two options are available: to run the
device throughout at 27 MHz or to enable the PLL. In the latter
case, even if the incoming data runs at 27 MHz, 4× Oversampling and the internal PLL will output the data at 54 MHz.
NOTE
In 4× Oversampling Mode the requirements for the optional
output filters are different from those in 2× Oversampling. (Mode
Register 1, Mode Register 6.) See Appendix 6 for further details.
ENCODER
ADV7190/ADV7191
The complete VBI is comprised of the following lines:
525/60 systems, Lines 525 to 21 for field one and Lines 262 to
284 for field two.
PIXEL BUS
MPEG2
625/50 systems, Line 624 to Line 22 and Lines 311 to 335.
The Opened VBI consists of:
ENCODER
CORE
27MHz
54MHz
525/60 systems, Lines 10 to 21 for field one and second half of
Lines 273 to 284 for field two.
PLL
I
N
T
E
R
P
2 O
ⴛ L
A
T
I
O
N
O
6 U
T
D P
A U
C T
S
54MHz
OUTPUT
625/50 systems, Lines 7 to 22 and Lines 319 to 335. (Mode
Register 3.)
2ⴛ FILTER
REQUIREMENTS
It is possible to allow control over the BLANK signal using
Timing Register 0. When the BLANK input is enabled (TR03 =
0 and input pin tied low), the BLANK input can be used to
input externally generated blank signals in Slave Mode 1, 2, or 3.
When the BLANK input is disabled (TR03 = 1 and input pin
tied low or tied high), the BLANK input is not used and the
ADV7190/ADV7191 automatically blanks all normally blank
lines as per CCIR-624. (Timing Register 0.)
4ⴛ FILTER
REQUIREMENTS
6.75
13.5
27.0
FREQUENCY – MHz
40.5
54.0
Figure 30. PLL and 4 × Oversampling Block Diagram
YUV LEVELS
This functionality allows the ADV7190/ADV7191 to output
SMPTE levels or Betacam levels on the Y output when configured in PAL or NTSC mode.
Sync
Video
Betacam
286 mV
714 mV
SMPTE
300 mV
700 mV
MII
300 mV
700 mV
As the data path is branched at the output of the filters the luma
signal relating to the CVBS or S-Video Y/C output is unaltered.
It is only the Y output of the YCrCb outputs that is scaled.
This control allows color component levels to have a peak-peak
amplitude of 700 mV, 1000 mV or the default values of 934 mV
in NTSC and 700 mV in PAL. (Mode Register 5.)
16-BIT INTERFACE
It is possible to input data in 16-bit format. In this case, the
interface only operates if the data is accompanied by separate
HSYNC/VSYNC/BLANK signals. Sixteen-bit mode is not available in Slave Mode 0 since EAV/SAV timing codes are used.
(Mode Register 8.)
4ⴛ OVERSAMPLING AND INTERNAL PLL
It is possible to operate all six DACs at 27 MHz (2× Oversampling) or 54 MHz (4× Oversampling).
REV. 0
VIDEO TIMING DESCRIPTION
The ADV7190/ADV7191 is intended to interface to off-theshelf MPEG1 and MPEG2 Decoders. As a consequence, the
ADV7190/ADV7191 accepts 4:2:2 YCrCb Pixel Data via a
CCIR-656 Pixel Port and has several Video Timing Modes of
operation that allow it to be configured as either System Master
Video Timing Generator or a Slave to the System Video Timing
Generator. The ADV7190/ADV7191 generates all of the required
horizontal and vertical timing periods and levels for the analog
video outputs.
The ADV7190/ADV7191 calculates the width and placement of
analog sync pulses, blanking levels, and color burst envelopes.
Color bursts are disabled on appropriate lines and serration and
equalization pulses are inserted where required.
In addition, the ADV7190/ADV7191 supports a PAL or NTSC
square pixel operation. The part requires an input pixel clock of
24.5454 MHz for NTSC square pixel operation and an input
pixel clock of 29.5 MHz for PAL square pixel operation. The
internal horizontal line counters place the various video waveform
sections in the correct location for the new clock frequencies.
The ADV7190/ADV7191 has four distinct Master and four
distinct Slave timing configurations. Timing Control is established with the bidirectional HSYNC, BLANK, and VSYNC
pins. Timing Register 1 can also be used to vary the timing
pulsewidths and where they occur in relation to each other.
(Mode Register 2, Timing Register 0, 1.)
–19–
ADV7190/ADV7191
RESET SEQUENCE
the encoder. Digital output timing signals become active and the
encoder timing is now under the control of the Timing Registers.
If at this stage, the user wishes to select a different video standard
to that on the NTSC_PAL pin, Standard I2C Control should be
enabled (MR25 = 1) and the video standard required is selected
by programming Mode Register 0 (Output Video Standard
Selection). Figure 31 illustrates the RESET sequence timing.
When RESET becomes active the ADV7190/ADV7191 reverts to
the default output configuration (see Appendix 8 for register
settings). The ADV7190/ADV7191 internal timing is under the
control of the logic level on the NTSC_PAL pin.
When RESET is released Y, Cr, Cb values corresponding to a
black screen are input to the ADV7190/ADV7191. Output
timing signals are still suppressed at this stage. DACs A, B, C
are switched off and DACs D, E, F are switched on.
When the user requires valid data, Pixel Data Valid Control is
enabled (MR26 = 1) to allow the valid pixel data to pass through
RESET
DAC D,
DAC E
XXXXXXX
XXXXXXX
BLACK VALUE WITH SYNC
VALID VIDEO
DAC F
XXXXXXX
XXXXXXX
BLACK VALUE
VALID VIDEO
DAC A,
DAC B,
DAC C
XXXXXXX
MR26
PIXEL_DATA_VALID
XXXXXXX
DIGITAL TIMING
XXXXXXX
VALID VIDEO
OFF
0
1
DIGITAL TIMING SIGNALS SUPPRESSED
TIMING ACTIVE
Figure 31. RESET Sequence Timing Diagram
–20–
REV. 0
ADV7190/ADV7191
CLOCK
COMPOSITE
VIDEO
e.g., VCR
OR CABLE
LCC1
GLL
VIDEO
DECODER
P19–P12
ADV7185
H/L TRANSITION
COUNT START
LOW
128
13
GREEN/COMPOSITE/Y
M
U
X
MPEG
DECODER
14 BITS
RESERVED
ADV7190/ADV7191
SCRESET/RTC/TR
BLUE/LUMA/U
P7–P0
RED/CHROMA/V
GREEN/COMPOSITE/Y
BLUE/LUMA/U
HSYNC
VSYNC
RED/CHROMA/V
SEQUENCE
BIT2
RESET
5 BITS
BIT3
RESERVED
RESERVED
4 BITS
RESERVED
0
FSCPLL INCREMENT1
21
0
RTC
TIME SLOT: 01
14
NOT USED IN
ADV7190
67 68
19
VALID
SAMPLE
8/LINE
LOCKED CLOCK
INVALID
SAMPLE
NOTES:
1F
SC PLL INCREMENT IS 22 BITS LONG, VALUE LOADED INTO ADV7190 FSC DDS REGISTER IS FSC PLL INCREMENTS BITS 21:0
PLUS BITS 0:9 OF SUBCARRIER FREQUENCY REGISTERS. ALL ZEROS SHOULD BE WRITTEN TO THE SUBCARRIER FREQUENCY
REGISTERS OF THE ADV7190/ADV7191.
2SEQUENCE BIT
PAL: 0 = LINE NORMAL, 1 = LINE INVERTED
NTSC: 0 = NO CHANGE
3RESET BIT
RESET ADV7190/ADV7191’s DDS
Figure 32. RTC Timing and Connections
Mode 0 (CCIR–656): Slave Option
(Timing Register 0 TR0 = X X X X X 0 0 0)
The ADV7190/ADV7191 is controlled by the SAV (Start Active Video) and EAV (End Active Video) Time Codes in the Pixel
Data. All timing information is transmitted using a 4-byte synchronization pattern. A synchronization pattern is sent immediately
before and after each line during active picture and retrace. Mode 0 is illustrated in Figure 33. The HSYNC, VSYNC and
BLANK pins (if not used) should be tied high during this mode.
ANALOG
VIDEO
EAV CODE
INPUT PIXELS
NTSC/PAL M SYSTEM
(525 LlNES/60Hz)
PAL SYSTEM
(625 LINES/50Hz)
C
F 0 0 X 8 1 8 1
Y r Y F 0 0 Y 0 0 0 0
4 CLOCK
SAV CODE
0 F F A A A
0 F F B B B
8 1 8 1 F 0 0 X C
C
C
C
C
0 0 0 0 F 0 0 Y b Y r Y b Y r Y b
ANCILLARY DATA
(HANC)
1440 CLOCK
4 CLOCK
4 CLOCK
280 CLOCK
END OF ACTIVE
VIDEO LINE
1440 CLOCK
START OF ACTIVE
VIDEO LINE
Figure 33. Timing Mode 0, Slave Mode
REV. 0
4 CLOCK
268 CLOCK
–21–
ADV7190/ADV7191
Mode 0 (CCIR–656): Master Option
(Timing Register 0 TR0 = X X X X X 0 0 1)
The ADV7190/ADV7191 generates H, V, and F signals required for the SAV and EAV Time Codes in the CCIR656 standard. The H bit
is output on the HSYNC pin, the V bit is output on the BLANK pin and the F bit is output on the VSYNC pin. Mode 0 is illustrated
in Figure 34 (NTSC) and Figure 35 (PAL). The H, V, and F transitions relative to the video waveform are illustrated in Figure 36.
DISPLAY
DISPLAY
522
523
VERTICAL BLANK
524
525
1
2
3
4
6
5
7
9
8
10
11
20
21
22
H
V
EVEN FIELD
F
ODD FIELD
DISPLAY
DISPLAY
VERTICAL BLANK
260
261
262
263
264
265
266
267
268
269
270
271
272
273
283
274
284
285
H
V
ODD FIELD
F
EVEN FIELD
Figure 34. Timing Mode 0, NTSC Master Mode
DISPLAY
DISPLAY
622
623
VERTICAL BLANK
624
625
1
2
3
4
5
6
7
21
22
23
H
V
F
EVEN FIELD
ODD FIELD
DISPLAY
DISPLAY
VERTICAL BLANK
309
310
311
312
313
314
315
316
317
318
319
320
334
335
336
H
V
F
ODD FIELD
EVEN FIELD
Figure 35. Timing Mode 0, PAL Master Mode
–22–
REV. 0
ADV7190/ADV7191
ANALOG
VIDEO
H
F
V
Figure 36. Timing Mode 0 Data Transitions, Master Mode
Mode 1: Slave Option HSYNC, BLANK, FIELD
(Timing Register 0 TR0 = X X X X X 0 1 0)
In this mode the ADV7190/ADV7191 accepts Horizontal SYNC and Odd/ Even FIELD signals. A transition of the FIELD
input when HSYNC is low indicates a new frame, i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK
input is disabled the ADV7190/ADV7191 automatically blanks all normally blank lines as per CCIR-624. Mode 1 is illustrated
in Figure 37 (NTSC) and Figure 38 (PAL).
DISPLAY
DISPLAY
522
523
524
VERTICAL BLANK
525
1
2
3
4
6
5
7
8
9
10
20
11
21
22
HSYNC
BLANK
EVEN FIELD
FIELD
ODD FIELD
DISPLAY
DISPLAY
260
261
262
VERTICAL BLANK
263
264
265
266
267
268
269
270
271
272
273
283
274
284
285
HSYNC
BLANK
ODD FIELD
FIELD
EVEN FIELD
Figure 37. Timing Mode 1, NTSC
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
3
4
5
6
7
21
22
23
HSYNC
BLANK
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
DISPLAY
309
310
VERTICAL BLANK
311
312
313
314
315
316
317
318
HSYNC
BLANK
FIELD
ODD FIELD
EVEN FIELD
Figure 38. Timing Mode 1, PAL
REV. 0
–23–
319
320
334
335
336
ADV7190/ADV7191
Mode 1: Master Option HSYNC, BLANK, FIELD
(Timing Register 0 TR0 = X X X X X 0 1 1)
In this mode the ADV7190/ADV7191 can generate Horizontal SYNC and Odd/Even FIELD signals. A transition of the FIELD
input when HSYNC is low indicates a new frame, i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK input is
disabled the ADV7190/ADV7191 automatically blanks all normally blank lines as per CCIR-624. Pixel data is latched on the
rising clock edge following the timing signal transitions. Mode 1 is illustrated in Figure 37 (NTSC) and Figure 38 (PAL). Figure 39
illustrates the HSYNC, BLANK and FIELD for an odd or even field transition relative to the pixel data.
HSYNC
FIELD
PAL = 12 ⴛ CLOCK/2
NTSC = 16 ⴛ CLOCK/2
BLANK
PIXEL
DATA
Cb
Y
Cr
Y
PAL = 132 ⴛ CLOCK/2
NTSC = 122 ⴛ CLOCK/2
Figure 39. Timing Mode 1, Odd/Even Field Transitions Master/Slave
Mode 2: Slave Option HSYNC, VSYNC, BLANK
(Timing Register 0 TR0 = X X X X X 1 0 0)
In this mode the ADV7190/ADV7191 accepts Horizontal and Vertical SYNC signals. A coincident low transition of both HSYNC
and VSYNC inputs indicates the start of an Odd Field. A VSYNC low transition when HSYNC is high indicates the start of an
Even Field. The BLANK signal is optional. When the BLANK input is disabled, the ADV7190/ADV7191 automatically blanks all
normally blank lines as per CCIR-624. Mode 2 is illustrated in Figure 40 (NTSC) and Figure 41 (PAL).
DISPLAY
522
523
524
DISPLAY
VERTICAL BLANK
525
1
2
3
4
6
5
7
8
10
9
11
20
21
22
HSYNC
BLANK
EVEN FIELD
VSYNC
ODD FIELD
DISPLAY
DISPLAY
260
261
262
263
VERTICAL BLANK
264
265
266
267
268
269
270
271
272
273
274
283
284
285
HSYNC
BLANK
VSYNC
ODD FIELD
EVEN FIELD
Figure 40. Timing Mode 2, NTSC
–24–
REV. 0
ADV7190/ADV7191
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
3
4
6
5
7
21
22
23
HSYNC
BLANK
VSYNC
EVEN FIELD
ODD FIELD
DISPLAY
DISPLAY
309
310
VERTICAL BLANK
311
312
313
314
315
316
318
317
319
320
334
335
336
HSYNC
BLANK
VSYNC
ODD FIELD
EVEN FIELD
Figure 41. Timing Mode 2, PAL
Mode 2: Master Option HSYNC, VSYNC, BLANK
(Timing Register 0 TR0 = X X X X X 1 0 1)
In this mode the ADV7190/ADV7191 can generate Horizontal and Vertical SYNC signals. A coincident low transition of both
HSYNC and VSYNC inputs indicates the start of an Odd Field. A VSYNC low transition when HSYNC is high indicates the
start of an Even Field. The BLANK signal is optional. When the BLANK input is disabled the ADV7190/ADV7191 automatically blanks
all normally blank lines as per CCIR-624. Mode 2 is illustrated in Figure 40 (NTSC) and Figure 41 (PAL). Figure 42 illustrates
the HSYNC, BLANK and VSYNC for an even-to-odd field transition relative to the pixel data. Figure 43 illustrates the HSYNC,
BLANK and VSYNC for an odd-to-even field transition relative to the pixel data.
HSYNC
VSYNC
PAL = 12 ⴛ CLOCK/2
NTSC = 16 ⴛ CLOCK/2
BLANK
PIXEL
DATA
Cb
Y
PAL = 132 ⴛ CLOCK/2
NTSC = 122 ⴛ CLOCK/2
Figure 42. Timing Mode 2, Even-to-Odd Field Transition Master/Slave
HSYNC
VSYNC
PAL = 12 ⴛ CLOCK/2
NTSC = 16 ⴛ CLOCK/2
PAL = 864 ⴛ CLOCK/2
NTSC = 858 ⴛ CLOCK/2
BLANK
Cb
PIXEL
DATA
Y
Cr
Y
Cb
PAL = 132 ⴛ CLOCK/2
NTSC = 122 ⴛ CLOCK/2
Figure 43. Timing Mode 2, Odd-to-Even Field Transition Master/Slave
REV. 0
–25–
Cr
Y
ADV7190/ADV7191
Mode 3: Master/Slave Option HSYNC, BLANK, FIELD
(Timing Register 0 TR0 = X X X X X 1 1 0 or X X X X X 1 1 1)
In this mode the ADV7190/ADV7191 accepts or generates Horizontal SYNC and Odd/Even FIELD signals. A transition of the
FIELD input when HSYNC is high indicates a new frame, i.e., Vertical Retrace. The BLANK signal is optional. When the
BLANK input is disabled the ADV7190/ADV7191 automatically blanks all normally blank lines as per CCIR-624. Mode 3 is illustrated
in Figure 44 (NTSC) and Figure 45 (PAL).
DISPLAY
522
523
524
DISPLAY
VERTICAL BLANK
525
1
2
3
4
6
5
7
8
9
10
20
11
21
22
HSYNC
BLANK
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
DISPLAY
260
261
262
263
VERTICAL BLANK
264
265
266
267
268
269
270
271
272
273
283
274
284
285
HSYNC
BLANK
FIELD
ODD FIELD
EVEN FIELD
Figure 44. Timing Mode 3, NTSC
DISPLAY
622
623
DISPLAY
VERTICAL BLANK
624
625
1
2
3
4
5
6
7
21
22
23
HSYNC
BLANK
FIELD
EVEN FIELD
ODD FIELD
DISPLAY
DISPLAY
309
310
VERTICAL BLANK
311
312
313
314
315
316
317
318
319
320
334
335
336
HSYNC
BLANK
FIELD
EVEN FIELD
ODD FIELD
Figure 45. Timing Mode 3, PAL
–26–
REV. 0
ADV7190/ADV7191
MPU PORT DESCRIPTION
The subaddresses autoincrement allowing data to be written to
or read from the starting subaddress. A data transfer is always
terminated by a stop condition. The user can also access any
unique subaddress register on a one-by-one basis without having
to update all the registers. There is one exception. The Subcarrier
Frequency Registers should be updated in sequence, starting
with Subcarrier Frequency Register 0. The autoincrement function
should be then used to increment and access Subcarrier Frequency
Registers 1, 2, and 3. The Subcarrier Frequency Registers should
not be accessed independently.
The ADV7190/ADV7191 supports a two-wire serial (I2 Ccompatible) microprocessor bus driving multiple peripherals.
Two inputs, Serial Data (SDA) and Serial Clock (SCL), carry
information between any device connected to the bus. Each
slave device is recognized by a unique address. The ADV7190/
ADV7191 has four possible slave addresses for both read and
write operations. These are unique addresses for each device
and are illustrated in Figure 46 and Figure 47. The LSB sets
either a read or write operation. Logic Level 1 corresponds to a
read operation while Logic Level 0 corresponds to a write operation. A1 is set by setting the ALSB pin of the ADV7190/ADV7191
to Logic Level 0 or Logic Level 1.
1
1
0
1
0
1
A1
Stop and start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of sequence
with normal read and write operations, they cause an immediate
jump to the idle condition. During a given SCL high period the
user should issue only one start condition, one stop condition,
or a single stop condition followed by a single start condition.
If, an invalid subaddress is issued by the user, the ADV7190/
ADV7191 will not issue an acknowledge and will return to the
idle condition. If in autoincrement mode, the user exceeds the
highest subaddress, the following action will be taken:
X
ADDRESS
CONTROL
SETUP BY
ALSB
READ/WRITE
CONTROL
0
WRITE
1
READ
1. In Read Mode, the highest subaddress register contents
will continue to be output until the master device issues a
no-acknowledge. This indicates the end of a read. A noacknowledge condition is where the SDA line is not pulled
low on the ninth pulse.
Figure 46. Slave Address
To control the various devices on the bus the following protocol
must be followed. First, the master initiates a data transfer by
establishing a start condition, defined by a high-to-low transition
on SDA while SCL remains high. This indicates that an address/
data stream will follow. All peripherals respond to the start condition and shift the next eight bits (7-bit address + R/W bit). The
bits are transferred from MSB down to LSB. The peripheral that
recognizes the transmitted address responds by pulling the data
line low during the ninth clock pulse. This is known as an acknowledge bit. All other devices withdraw from the bus at this point
and maintain an idle condition. The idle condition is where
the device monitors the SDA and SCL lines waiting for the
start condition and the correct transmitted address. The R/W bit
determines the direction of the data.
2. In Write Mode, the data for the invalid byte will be not be
loaded into any subaddress register, a no-acknowledge will
be issued by the ADV7190/ADV7191 and the part will return
to the idle condition.
SDATA
SCLOCK
S
1–7
8
9
1–7
8
9
1–7
START ADDR R/W ACK SUBADDRESS ACK
DATA
SLAVE ADDR A(S)
SUB ADDR
Figure 48 shows bus write and read sequences.
READ
SEQUENCE
S
SLAVE ADDR A(S)
S = START BIT
P = STOP BIT
A(S)
DATA
A(S)
DATA
SUB ADDR
A(S) S SLAVE ADDR
A(S) = ACKNOWLEDGE BY SLAVE
A(M) = ACKNOWLEDGE BY MASTER
A(S)
DATA
–27–
A(M)
A(S) = NO ACKNOWLEDGE BY SLAVE
A(M) = NO ACKNOWLEDGE BY MASTER
Figure 48. Write and Read Sequences
REV. 0
A(S) P
LSB = 1
LSB = 0
P
STOP
Figure 47 illustrates an example of data transfer for a read
sequence and the start and stop conditions.
The ADV7190/ADV7191 acts as a standard slave device on
the bus. The data on the SDA pin is eight bits long supporting
the 7-bit addresses plus the R/W bit. It interprets the first byte as
the device address and the second byte as the starting subaddress.
S
9
ACK
Figure 47. Bus Data Transfer
A Logic 0 on the LSB of the first byte means that the master
will write information to the peripheral. A Logic 1 on the LSB
of the first byte means that the master will read information
from the peripheral.
WRITE
SEQUENCE
8
DATA
A(M) P
ADV7190/ADV7191
REGISTER ACCESSES
Subaddress Register (SR7–SR0)
The MPU can write to or read from all of the registers of the
ADV7190/ADV7191 with the exception of the Subaddress Registers, which are write-only registers. The Subaddress Register
determines which register the next read or write operation accesses. All communications with the part through the bus start
with an access to the Subaddress Register. Then a read/write
operation is performed from/to the target address which then
increments to the next address until a stop command on the bus is
performed.
The Communications Register is an eight bit write-only register.
After the part has been accessed over the bus and a read/write
operation is selected, the subaddress is set up. The Subaddress
Register determines to/from which register the operation takes
place.
Figure 49 shows the various operations under the control of the
Subaddress Register 0 should always be written to SR7.
Register Select (SR6–SR0)
These bits are set up to point to the required starting address.
REGISTER PROGRAMMING
The following section describes each register. All registers can
be read from as well as written to.
SR7
SR7
ZERO SHOULD
BE WRITTEN
HERE
SR6
SR5
SR4
SR3
SR2
SR1
SR0
ADV7190/ADV7191 SUBADDRESS REGISTER
ADDRESS
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
1AH
1BH
1CH
1DH
1EH
1FH
20H
21H
22H
23H
24H
25H
26H
27H
28H
29H
2AH
2BH
2CH
2DH
2EH
2FH
30H
31H
32H
33H
34H
35H
36H
37H
38H
39H
3AH
3BH
3CH
3DH
3EH
3FH
40H
41H
42H
43H
44H
45H
46H
47H
48H
49H
4AH
4BH
SR6 SR5 SR4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
1
1
1
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
SR3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
1
SR2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
SR1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
0
1
SR0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
MODE REGISTER 0
MODE REGISTER 1
MODE REGISTER 2
MODE REGISTER 3
MODE REGISTER 4
MODE REGISTER 5
MODE REGISTER 6
MODE REGISTER 7
MODE REGISTER 8
MODE REGISTER 9
TIMING REGISTER 0
TIMING REGISTER 1
SUBCARRIER FREQUENCY REGISTER 0
SUBCARRIER FREQUENCY REGISTER 1
SUBCARRIER FREQUENCY REGISTER 2
SUBCARRIER FREQUENCY REGISTER 3
SUBCARRIER PHASE REGISTER
CLOSED CAPTIONING EXTENDED DATA BYTE 0
CLOSED CAPTIONING EXTENDED DATA BYTE 1
CLOSED CAPTIONING DATA BYTE 0
CLOSED CAPTIONING DATA BYTE 1
NTSC PEDESTAL/TELETEXT CONTROL REGISTER 0
NTSC PEDESTAL/TELETEXT CONTROL REGISTER 1
NTSC PEDESTAL/TELETEXT CONTROL REGISTER 2
NTSC PEDESTAL/TELETEXT CONTROL REGISTER 3
CGMS/WSS 0
CGMS/WSS 1
CGMS/WSS 2
TELETEXT REQUEST CONTROL REGISTER
CONTRAST CONTROL REGISTER
U SCALE
V SCALE
HUE ADJUST CONTROL REGISTER
BRIGHTNESS CONTROL REGISTER
SHARPNESS CONTROL REGISTER
DNR 0
DNR 1
DNR 2
GAMMA CORRECTION REGISTER 0
GAMMA CORRECTION REGISTER 1
GAMMA CORRECTION REGISTER 2
GAMMA CORRECTION REGISTER 3
GAMMA CORRECTION REGISTER 4
GAMMA CORRECTION REGISTER 5
GAMMA CORRECTION REGISTER 6
GAMMA CORRECTION REGISTER 7
GAMMA CORRECTION REGISTER 8
GAMMA CORRECTION REGISTER 9
GAMMA CORRECTION REGISTER 10
GAMMA CORRECTION REGISTER 11
GAMMA CORRECTION REGISTER 12
GAMMA CORRECTION REGISTER 13
BRIGHTNESS DETECT REGISTER
OUTPUT CLOCK REGISTER
RESERVED
RESERVED
RESERVED
RESERVED
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
MACROVISION REGISTER
Figure 49. Subaddress Register
–28–
REV. 0
ADV7190/ADV7191
MODE REGISTER 0
MR0 (MR07–MR00)
(Address (SR4–SR0) = 00H)
MODE REGISTER 1
MR1 (MR17–MR10)
(Address (SR4–SR0) = 01H)
Figure 50 shows the various operations under the control of
Mode Register 0.
Figure 51 shows the various operations under the control of
Mode Register 1.
MR0 BIT DESCRIPTION
Output Video Standard Selection (MR00–MR01)
MR1 BIT DESCRIPTION
DAC Control (MR10–MR15)
These bits are used to set up the encoder mode. The ADV7190/
ADV7191 can be set up to output NTSC, PAL (B, D, G, H, I),
PAL M or PAL N standard video.
Bits MR15–MR10 can be used to power down the DACs. This are
used to reduce the power consumption of the ADV7190/ADV7191
or if any of the DACs are not required in the application.
Luminance Filter Select (MR02–MR04)
4 Oversampling Control (MR16)
These bits specify which luma filter is to be selected. The filter
selection is made independent of whether PAL or NTSC is
selected.
To enable 4× Oversampling this bit has to be set to 1. When
enabled, the data is output at a frequency of 54 MHz.
Note that PLL Enable Control has to be enabled (MR61 = 0) in
4× Oversampling mode.
Chrominance Filter Select (MR05–MR07)
These bits select the chrominance filter. A low-pass filter can be
selected with a choice of cut-off frequencies (0.65 MHz, 1.0 MHz,
1.3 MHz, 2 MHz, or 3 MHz) along with a choice of CIF or
QCIF filters.
MR07
MR06
MR05
Reserved (MR17)
A Logical 0 must be written to this bit.
MR04
MR03
MR02
MR01
OUTPUT VIDEO
STANDARD SELECTION
CHROMA FILTER SELECT
MR07 MR06 MR05
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
MR00
MR01 MR00
1.3 MHz LOW-PASS FILTER
0.65 MHz LOW-PASS FILTER
1.0 MHz LOW-PASS FILTER
2.0 MHz LOW-PASS FILTER
RESERVED
CIF
QCIF
3.0 MHz LOW-PASS FILTER
0
0
1
1
0
1
0
1
NTSC
PAL (B, D, G, H, I)
PAL (M)
PAL (N)
LUMA FILTER SELECT
MR04 MR03 MR02
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
LOW-PASS FILTER (NTSC)
LOW-PASS FILTER (PAL)
NOTCH FILTER (NTSC)
NOTCH FILTER (PAL)
EXTENDED MODE
CIF
QCIF
RESERVED
Figure 50. Mode Register 0 (MR0)
MR17
MR17
ZERO MUST
BE WRITTEN
TO THIS BIT
MR16
MR15
MR13
DAC A
DAC CONTROL
0
1
MR12
0
1
MR11
POWER-DOWN
NORMAL
DAC B
DAC CONTROL
MR14
0
1
0
1
POWER-DOWN
NORMAL
DAC D
DAC CONTROL
MR12
POWER-DOWN
NORMAL
0
1
–29–
DAC F
DAC CONTROL
MR10
POWER-DOWN
NORMAL
Figure 51. Mode Register 1 (MR1)
REV. 0
MR10
DAC E
DAC CONTROL
MR13
POWER-DOWN
NORMAL
2 OVERSAMPLING
4 OVERSAMPLING
MR11
DAC C
DAC CONTROL
MR15
4 OVERSAMPLING
CONTROL
MR16
0
1
MR14
0
1
POWER-DOWN
NORMAL
ADV7190/ADV7191
Standard I2C Control (MR25)
MODE REGISTER 2
MR2 (MR27–MR20)
(Address (SR4–SR0) = 02H)
This bit controls the video standard used by the ADV7190/
ADV7191. When this bit is set to 1 the video standard as programmed in Output Video Standard Selection (MR00, MR01).
When MR25 is set to 0, the ADV7190/ADV7191 is forced into
the standard selected by the NTSC_PAL pin. When NTSC_PAL
is low the standard is NTSC, when the NTSC_PAL pin is high,
the standard is PAL.
Mode Register 2 is a 8-bit wide register.
Figure 52 shows the various operations under the control of Mode
Register.
MR2 BIT DESCRIPTION— RGB/YUV Control (MR20)
This bit enables the output from the small or large DACs to be
set to YUV or RGB output video standard.
Pixel Data Valid Control (MR26)
This bit controls the output from DACs A, B, and C. When this
bit is set to 1, Composite, Luma, and Chroma Signals are output from DACs A, B, and C (respectively). When this bit is set
to 0, RGB or YUV may be output from these DACs.
After resetting the device, this bit has the value 0 and the pixel
data input to the encoder is blanked such that a black screen is
output from the DACs. The ADV7190/ADV7191 will be set
to Master Mode timing. When this bit is set to 1 by the user
(via the I2C), pixel data passes to the pins and the encoder reverts to the Timing Mode defined by Timing Register 0.
SCART Enable Control (MR22)
Sleep Mode Control (MR27)
DAC Output Control (MR21)
This bit is used to switch the DAC outputs from SCART to a
EUROSCART configuration. A complete table of all DAC output configurations is shown in Table III.
When this bit is set (1), Sleep Mode is enabled. With this mode
enabled, the ADV7190/ADV7191 current consumption is reduced
to less than 1 mA. The I2C registers can be written to and read
from when the ADV7190/ADV7191 is in Sleep Mode.
Pedestal Control (MR23)
This bit specifies whether a pedestal is to be generated on the
NTSC composite video signal. This bit is invalid when the device
is configured in PAL mode.
When the device is in Sleep Mode and 0 is written to MR27, the
ADV7190/ADV7191 will come out of Sleep Mode and resume
normal operation. Also, if a RESET is applied during Sleep
Mode, the ADV7190/ADV7191 will come out of Sleep Mode
and resume normal operation.
Square Pixel Control (MR24)
This bit is used to set up square pixel mode. This is available in
Slave Mode only. For NTSC, a 24.5454 MHz clock must be
supplied. For PAL, a 29.5 MHz clock must be supplied. Square
pixel operation is not available in 4× Oversampling mode.
For this to operate, Power Up in Sleep Mode Control has to be
enabled (MR60 = 0), otherwise Sleep Mode is controlled by
the PAL_NTSC and SCRESET/RTC/TR pins.
Table III. DAC Output Configuration Matrix
SCART
MR22
DAC O/P
MR21
RGB/YUV
MR20
DAC A
DAC B
DAC C
DAC D
DAC E
DAC F
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
G
Y
CVBS
CVBS
CVBS
CVBS
CVBS
CVBS
B
U
LUMA
LUMA
B
U
LUMA
LUMA
R
V
CHROMA
CHROMA
R
V
CHROMA
CHROMA
CVBS
CVBS
G
Y
G
Y
G
Y
LUMA
LUMA
B
U
LUMA
LUMA
B
U
CHROMA
CHROMA
R
V
CHROMA
CHROMA
R
V
MR27
MR26
MR25
PIXEL DATA
VALID CONTROL
MR26
0
DISABLE
1
ENABLE
SLEEP MODE
CONTROL
MR27
0
DISABLE
1
ENABLE
MR24
MR23
SQUARE PIXEL
CONTROL
MR25
0
DISABLE
1
ENABLE
MR21
SCART ENABLE
CONTROL
MR24
0
DISABLE
1
ENABLE
STANDARD I2C
CONTROL
MR22
MR22
0
DISABLE
1
ENABLE
MR20
RGB/YUV
CONTROL
MR20
0
RGB OUTPUT
1
YUV OUTPUT
PEDESTAL
CONTROL
DAC OUTPUT
CONTROL
MR23
0
PEDESTAL OFF
1
PEDESTAL ON
MR21
0
RGB/YUV/COMP
1
COMP/LUMA/CHROMA
Figure 52. Mode Register 2 (MR2)
–30–
REV. 0
ADV7190/ADV7191
Genlock Control (MR41–MR42)
MODE REGISTER 3
MR3 (MR37–MR30)
(Address (SR4–SR0) = 03H)
Mode Register 3 is a 8-bit wide register. Figure 53 shows the
various operations under the control of Mode Register 3.
These bits control the Genlock feature and timing reset of
the ADV7190/ADV7191 Setting MR41 and MR42 to Logic 0
disables the SCRESET/RTC/TR pin and allows the ADV7190/
ADV7191 to operate in normal mode.
MR3 BIT DESCRIPTION
Revision Code (MR30–MR31)
1. By setting MR41 to zero and MR42 to one a timing reset is
applied, resetting the horizontal and vertical counters. This
has the effect of resetting the Field Count to Field 0.
This bit is read only and indicates the revision of the device.
If the SCRESET/RTC/TR pin is held high, the counters
will remain reset. Once the pin is released the counters will
commence counting again. For correct counter reset, the
SCRESET/RTC/TR pin has to remain high for at least
37 ns (one clock cycle at 27 MHz).
VBI_Open (MR32)
This bit determines whether or not data in the Vertical Blanking
Interval (VBI) is output to the analog outputs or blanked. Note
that this condition is also valid in Timing Slave Mode 0. For
further information see Vertical Blanking Data Insertion and
BLANK Input section.
2. If MR41 is set to one and MR42 is set to zero, the SCRESET/
RTC/TR pin is configured as a subcarrier reset input and
the subcarrier phase will reset to Field 0 whenever a low-tohigh transition is detected on the SCRESET/RTC/TR pin
(SCH phase resets at the start of the next field).
Teletext Enable (MR33)
This bit must be set to 1 to enable teletext data insertion on
the TTX pin.
Teletext Bit Request Mode Control (MR34)
3. If MR41 is set to one and MR42 is set to one, the SCRESET/
RTC/TR pin is configured as a real-time control input and
the ADV7190/ADV7191 can be used to lock to an external
video source working in RTC mode. For more information see
Real-Time Control, Subcarrier Reset and Timing Reset section.
This bit enables switching of the teletext request signal from a
continuous high signal (MR34 = 0) to a bitwise request signal
(MR34 = 1).
Closed Captioning Field Control (MR35–MR36)
These bits control the fields that closed captioning data is displayed on, closed captioning information can be displayed on
an odd field, even field or both fields.
Active Video Line Duration (MR43)
This bit switches between two active video line durations. A zero
selects CCIR Rec. 601 (720 pixels PAL/NTSC) and a one
selects ITU-R BT. 470 standard for active video duration (710
pixels NTSC, 702 pixels PAL).
Reserved (MR37)
A Logic 0 must be written to this bit.
Chrominance Control (MR44)
MODE REGISTER 4
MR4 (MR47–MR40)
(Address (SR4–SR0) = 04H)
This bit enables the color information to be switched on and off
the chroma composite, color component outputs.
Mode Register 4 is a 8-bit wide register. Figure 54 shows the
various operations under the control of Mode Register 4.
Burst Control (MR45)
MR4 BIT DESCRIPTION
VSYNC_3H Control (MR40)
Color Bar Control (MR46)
This bit enables the color burst to be switched on and off the
chroma and composite outputs.
This bit can be used to generate and output an internal color
bar test pattern. The color bar configuration is 100/7.5/75/7.5
for NTSC and 100/0/75/0 for PAL. It is important to note that
when color bars are enabled the ADV7190/ADV7191 is configured in a Master Timing mode. The output pins VSYNC,
HSYNC and BLANK are three-state during color bar mode.
When this bit is enabled (1) in Slave Mode, it is possible to
drive the VSYNC input low for 2.5 lines in PAL mode and
three lines in NTSC mode. When this bit is enabled in Master
Mode the ADV7190/ADV7191 outputs an active low VSYNC
signal for three lines in NTSC mode and 2.5 lines in PAL mode.
MR37
MR36
MR35
MR34
MR33
MR32
TTX BIT REQUEST
MODE CONTROL
MR37
MR34
0
DISABLE
1
ENABLE
ZERO MUST BE
WRITTEN TO
THIS BIT
CLOSED CAPTIONING
FIELD CONTROL
MR36 MR35
0
0
0
1
1
0
1
1
NO DATA OUT
ODD FIELD ONLY
EVEN FIELD ONLY
DATA OUT
(BOTH FIELDS)
VBI OPEN
MR32
0
DISABLE
1
ENABLE
TELETEXT
ENABLE
MR33
0
DISABLE
1
ENABLE
Figure 53. Mode Register 3 (MR3)
REV. 0
–31–
MR31
MR30
MR31 MR30
RESERVED FOR
REVISION CODE
ADV7190/ADV7191
MR47
MR46
MR45
COLOR BAR
CONTROL
MR46
0
DISABLE
1
ENABLE
INTERLACED
MODE CONTROL
MR44
CHROMINANCE
CONTROL
MR44
0
ENABLE COLOR
1
DISABLE COLOR
BURST
CONTROL
MR47
0
INTERLACED
1
NONINTERLACED
MR43
MR42
MR41
GENLOCK CONTROL
MR42 MR41
0
0
0
1
1
1
0
1
DISABLE GENLOCK
ENABLE SUBCARRIER
RESET PIN
TIMING RESET
ENABLE RTC PIN
ACTIVE VIDEO
LINE DURATION
MR43
0
720 PIXELS
1
710 PIXELS/702 PIXELS
MR45
0
ENABLE BURST
1
DISABLE BURST
MR40
VSYNC 3H CONTROL
MR40
0
1
DISABLE
ENABLE
Figure 54. Mode Register 4 (MR4)
It is also possible to have default values of 934 mV for NTSC
and 700 mV for PAL (MR52 + MR51 = 00).
Interlaced Mode Control (MR47)
This bit is used to setup the output to interlaced or noninterlaced
mode.
RGB Sync (MR53)
This bit is used to set up the RGB outputs with the sync information encoded on all RGB outputs.
MODE REGISTER 5
MR5 (MR57–MR50)
(Address (SR4–SR0) = 05H)
Clamp Delay Value (MR54–MR55)
These bits control the delay or advance of the CLAMP signal
in the front or back porch of the ADV7190/ADV7191. It is possible to delay or advance the pulse by zero, one, two, or three
clock cycles.
Mode Register 5 is a 8-bit wide register. Figure 55 shows the
various operations under the control of Mode Register 5.
MR5 BIT DESCRIPTION
Y-Level Control (MR50)
Note: Pin 51 is a multifunctional pin (VSO/CLAMP). CLAMP/
VSO Select Control (MR77) has to be set accordingly.
This bit controls the component Y output level on the ADV7190/
ADV7191. If this bit is set (0), the encoder outputs Betacam
levels when configured in PAL or NTSC mode. If this bit is
set (1), the encoder outputs SMPTE levels when configured
in PAL or NTSC mode.
Clamp Delay Direction (MR56)
This bit controls a positive or negative delay in the CLAMP signal. If this bit is set (1), the delay is negative. If it is set (0), the
delay is positive.
UV-Levels Control (MR51–MR52)
Clamp Position (MR57)
These bits control the component U and V output levels on
the ADV7190/ADV7191. It is possible to have UV levels with
a peak-to-peak amplitude of either 700 mV (MR52 + MR51
= 01 ) or 1000 mV (MR52 + MR51 = 10) in NTSC and PAL.
MR57
MR56
MR55
This bit controls the position of the CLAMP signal. If this bit is
set (1), the CLAMP signal is located in the back porch position.
If this bit is set (0), the CLAMP signal is located in the front
porch position.
MR54
MR53
CLAMP DELAY
DIRECTION
MR57
0
FRONT PORCH
1
BACK PORCH
0
1
0
1
0
1
MR50
0
DISABLE
1
ENABLE
DISABLE
ENABLE
CLAMP DELAY
MR50
Y LEVEL
CONTROL
MR53
UV LEVEL CONTROL
MR52 MR51
MR55 MR54
0
0
1
1
MR51
RGB SYNC
MR56
0
POSITIVE
1
NEGATIVE
CLAMP
POSITION
MR52
NO DELAY
1 PCLK
2 PCLK
3 PCLK
0
0
1
1
0
1
0
1
DEFAULT LEVELS
700mV
1000mV
RESERVED
Figure 55. Mode Register 5 (MR5)
–32–
REV. 0
ADV7190/ADV7191
MODE REGISTER 6
MR6 (MR67–MR60)
(ADDRESS (SR4–SR0) = 06H)
Luma Saturation Control (MR71)
When this bit is set (1), the luma signal will be clipped if it reaches
a limit that corresponds to an input luma value of 255 (after
scaling by the Contrast Control Register). This prevents the
chrominance component of the composite video signal being
clipped if the amplitude of the luma is too high. When this bit is
set (0), this control is disabled.
Mode Register 6 is an 8-bit-wide register. Figure 56 shows the
various operations under the control of Mode Register 6.
MR6 BIT DESCRIPTION
Power-Up Sleep Mode Control (MR60)
Hue Adjust Control (MR72)
After RESET is applied this control is enabled (MR60 = 0) if
both SCRESET/RTC/TR and NTSC_PAL pins are tied high.
The ADV7190/ADV7191 will then power up in Sleep Mode to
facilitate low power consumption while the I2C is initialized.
When this control is disabled (MR60 = 1, via the I2C) Sleep
Mode control passes to Sleep Mode Control, MR27.
This bit is used to enable hue adjustment on the composite and
chroma output signals of the ADV7190/ADV7191. When this
bit is set (1), the hue of the color is adjusted by the phase offset
described in the Hue Adjust Control Register. When this bit is
set (0), hue adjustment is disabled.
Brightness Enable Control (MR73)
PPL Enable Control (MR61)
Reserved (MR62, MR63, MR64)
This bit is used to enable the brightness control of the ADV7190/
ADV7191. The actual brightness level is programmed in the
Brightness Control Register. This value or “setup” level is added to
the scaled Y data. When this bit is set (1), brightness control
is enabled. When this bit is set (0), brightness control is disabled.
A Logic 0 must be written to these bits.
Sharpness Filter Enable (MR74)
Field Counter (MR65, MR66, MR67)
This bit is used to enable the sharpness control of the luminance
signal on the ADV7190/ADV7191 (Luma Filter Select has to
be set to Extended, i.e., MR04–MR02 = 100). The various
responses of the filter are determined by the Sharpness Control Register. When this bit is set (1), the luma response is altered
by the amount described in the Sharpness Control Register.
When this bit is set (0), the sharpness control is disabled. See Internal Filter Response section for luma signal responses.
The PLL control should be enabled (MR61 = 0 ) when 4×
Oversampling is enabled (MR16 = 1). It is also used to reset the
PLL when this bit is toggled.
These three bits are read-only bits. The field count can be read
back over the I2C interface. In NTSC mode the field count goes
from 0–3, in PAL Mode from 0–7.
MODE REGISTER 7
MR7 (MR77–MR70)
(Address (SR4–SR0) = 07H)
Mode Register 7 is an 8-bit wide register. Figure 57 shows the
various operations under the control of Mode Register 7.
CSO_HSO Output Control (MR75)
This bit is used to determine whether HSO or CSO TTL output
signal is output at the CSO_HSO pin. If this bit is set 1, then
the CSO TTL signal is output. If this bit is set 0, the HSO TTL
signal is output.
MR7 BIT DESCRIPTION
Color Control Enable (MR70)
This bit is used to enable control of contrast and saturation of
color. If this bit is set (1) color controls are enabled (Contrast
Control Register, U-Scale Register, V-Scale Register). If this bit
is set (0), the color control features are disabled.
MR67
MR66
MR65
MR64
MR63
MR62
MR67 MR66 MR65
MR64 MR63 MR62
FIELD COUNTER
ZERO MUST
BE WRITTEN
TO THESE BITS
MR61
MR60
PLL ENABLE
CONTROL
MR61
0
1
POWER-UP SLEEP
MODE CONTROL
ENABLED
DISABLED
MR60
0
ENABLED
1
DISABLED
Figure 56. Mode Register 6 (MR6)
MR77
MR76
MR75
MR76
ZERO MUST
BE WRITTEN
TO THIS BIT
CLAMP/ VSO SELECT
MR77
0
VSO OUTPUT
1
CLAMP OUTPUT
MR74
SHARPNESS FILTER
ENABLE
MR74
0
DISABLE
1
ENABLE
CSO_HSO
OUTPUT CONTROL
MR75
0
1
MR73
HSO OUT
CSO OUT
MR72
MR71
HUE ADJUST
CONTROL
MR72
0
DISABLE
1
ENABLE
BRIGHTNESS
ENABLE CONTROL
MR73
0
DISABLE
1
ENABLE
–33–
COLOR CONTROL
ENABLE
MR70
0
DISABLE
1
ENABLE
LUMA SATURATION
CONTROL
MR71
0
DISABLE
1
ENABLE
Figure 57. Mode Register 7 (MR7)
REV. 0
MR70
ADV7190/ADV7191
A Logic 0 must be written to this bit.
on Gamma Correction controls see Gamma Correction Registers
0–13 (Gamma 0–13) (Address (SR5–SR0) = 26H–32H section.
CLAMP/VSO Select (MR77)
Gamma Curve Select Control (MR87)
This bit is used to select the functionality of Pin 51. A 1 selects
CLAMP as the output signal. A 0 selects VSO output.
This bit selects which of the two programmable gamma curves is
used. When setting MR87 to 0, the gamma correction curve to be
processed is Curve A. Otherwise, Curve B is selected. For further information on Gamma Correction controls see Gamma
Correction Registers 0–13 (Gamma 0–13) (Address (SR5–SR0)
= 26H–32H section.
Reserved (MR76)
MODE REGISTER 8
MR8 (MR87–MR80)
(Address (SR4–SR0) = 08H)
Mode Register 8 is an 8-bit-wide register. Figure 58 shows the
various operations under the control of Mode Register 8.
MODE REGISTER 9
MR9 (MR97–MR90)
(Address (SR4–SR0) = 09H)
MR8 BIT DESCRIPTION
Reserved (MR80, MR81)
Mode Register 9 is an 8-bit-wide register. Figure 59 shows
the various operations under the control of Mode Register 9.
A Logic 0 must be written to these bits.
Double Buffer Control (MR82)
MR9 BIT DESCRIPTION
Undershoot Limiter (MR90–MR91)
Double buffering can be enabled or disabled on the Contrast
Control Register, U Scale Register, V Scale Register, Hue Adjust
Control Register, Closed Captioning Register, Brightness Control Register, Gamma Curve Select Bit and the Macrovision
Registers. Double Buffering is not available in Master Timing
mode.
This control ensures that no luma video data will go below a
programmable level. This prevents any synchronization problems
due to luma signals going below the blanking level. Available
limit levels are –1.5 IRE, –6 IRE, –11 IRE.
Note that this facility is only available in 4× Oversampling mode
(MR16 = 1). When the device is operated in 2× Oversampling
mode (MR16 = 0) or RGB outputs without RGB sync are
selected, the minimum luma level is set in Timing Register 0,
TR06 (Min Luma Control).
16-Bit Pixel Port (MR83)
This bit controls if the ADV7190/ADV7191 accepts 8-bit or
16-bit input data. In 8-bit mode the data will be input on Pins
P0–P7. Unused pixel inputs should be grounded.
Reserved (MR84)
Reserved (MR92–MR93)
A Logic 0 must be written to this bit.
A Logic 0 must be written to these bits.
DNR Enable Control (MR85)
Chroma Delay Control (MR94–MR95)
To enable the DNR process this bit has to be set to 1. If this bit
is set to 0, the DNR processing is bypassed. For further information on DNR controls see DNR Registers 2–0, DNR1 Bit
Description, and DNR2 Bit Description sections.
The Chroma Signal can be delayed by up to 296 ns (eight clock
cycles at 27 MHz) using MR94–MR95. For further information see also Chroma/Luma Delay section.
Reserved (MR96–MR97)
Gamma Enable Control (MR86)
A Logic 0 must be written to these bits.
To enable the programmable gamma correction this bit has
to be set to enabled (MR86 is set to 1). For further information
MR87
MR86
MR85
GAMMA ENABLE
CONTROL
MR86
0
DISABLE
1
ENABLE
GAMMA CURVE
SELECT CONTROL
MR87
0
CURVE A
1
CURVE B
MR84
MR83
MR84
MR81
DOUBLE BUFFER
CONTROL
MR82
0
DISABLE
1
ENABLE
ZERO MUST
BE WRITTEN
TO THIS BIT
DNR ENABLE
CONTROL
MR85
0
DISABLE
1
ENABLE
MR82
MR80
MR81 MR80
ZERO MUST
BE WRITTEN
TO THESE BITS
16-PIXEL PORT
MR83
0
8-BIT PIXEL PORT
1
16-BIT PIXEL PORT
Figure 58. Mode Register 8 (MR8)
MR97
MR96
MR95
MR97 MR96
ZERO MUST
BE WRITTEN
TO THESE BITS
MR94
MR93
MR95 MR94
0
1
0
1
MR91
MR93 MR92
CHROMA
DELAY CONTROL
0
0
1
1
MR92
0ns DELAY
148ns DELAY
296ns DELAY
RESERVED
ZERO MUST
BE WRITTEN
TO THESE BITS
MR90
UNDERSHOOT
LIMITER
MR91 MR90
0
0
1
1
0
1
0
1
DISABLED
–11 IRE
–6 IRE
–1.5 IRE
Figure 59. Mode Register 9 (MR9)
–34–
REV. 0
ADV7190/ADV7191
TIMING REGISTER 0 (TR07–TR00)
(Address (SR4–SR0) = 0AH)
TIMING REGISTER 1
(TR17–TR10)
(Address (SR4–SR0) = 0BH)
Figure 60 shows the various operations under the control of
Timing Register 0. This register can be read from as well as
written to.
Timing Register 1 is an 8-bit-wide register.
Figure 61 shows the various operations under the control of
Timing Register 1. This register can be read from as well written
to. This register can be used to adjust the width and position of
the master mode timing signals.
TR0 BIT DESCRIPTION
Master/Slave Control (TR00)
This bit controls whether the ADV7190/ADV7191 is in master or
slave mode.
TR1 BIT DESCRIPTION
HSYNC Width (TR10–TR11)
Timing Mode Selection (TR01–TR02)
These bits control the timing mode of the ADV7190/ADV7191.
These modes are described in more detail in the Video Timing Description and RESET Sequence sections of the data sheet.
These bits adjust the HSYNC pulsewidth.
BLANK Input Control (TR03)
These bits adjust the position of the HSYNC output relative to
the VSYNC output.
This bit controls whether the BLANK input is used to accept
blank signals or whether blank signals are internally generated.
HSYNC to VSYNC Rising Edge Control (TR14–TR15)
When the ADV7190/ADV7191 is in Timing Mode 1, these bits
adjust the position of the HSYNC output relative to the VSYNC
output rising edge.
Luma Delay (TR04–TR05)
The luma signal can be delayed by up to 222 ns (or six clock
cycles at 27 MHz) using TR04–TR05. For further information
see Chroma/Luma Delay section.
TPCLK = one clock cycle at 27 MHz.
VSYNC Width (TR14–TR15)
When the ADV7190/ADV7191 is configured in Timing Mode
2, these bits adjust the VSYNC pulsewidth.
Min Luminance Value (TR06)
This bit is used to control the minimum luma output value
by the ADV7190/ADV7191 in 2× Oversampling Mode (MR 16 =
0). When this bit is set to a Logic 1, the luma is limited to 7.5IRE
below the blank level. When this bit is set to (0), the luma value
can be as low as the sync bottom level (40IRE below blanking).
TPCLK = one clock cycle at 27 MHz.
HSYNC to Pixel Data Adjust (TR16–TR17)
This enables the HSYNC to be adjusted with respect to the
pixel data. This allows the Cr and Cb components to be swapped.
This adjustment is available in both master and slave timing
modes.
Timing Register Reset (TR07)
Toggling TR07 from low to high and low again resets the internal timing counters. This bit should be toggled after power-up,
reset, or changing to a new timing mode.
TR06
TR05
TPCLK = one clock cycle at 27 MHz.
TR04
TR03
TR02
TR07
LUMA DELAY
MIN LUMINANCE VALUE
TR05 TR04
0
0
1
1
0
1
0
1
0ns DELAY
74ns DELAY
148ns DELAY
222ns DELAY
–35–
TR00
MASTER / SLAVE
CONTROL
TR00
0
SLAVE TIMING
1
MASTER TIMING
TIMING MODE
CONTROL
TR02 TR01
0
0
0
1
1
0
1
1
Figure 60. Timing Register 0
REV. 0
TR01
BLANK INPUT
CONTROL
TR03
0
ENABLE
1
DISABLE
TIMING
REGISTER RESET
TR06
0
LUMA MIN =
SYNC BOTTOM
1
LUMA MIN =
BLANK –7.5 IRE
HSYNC to VSYNC Delay Control (TR12–TR13)
TPCLK = one clock cycle at 27 MHz.
Note: When this input pin is tied high (to 5 V), the input is disabled regardless of the register setting. It, therefore, should be
tied low (to Ground) to allow control over the I2C register.
TR07
TPCLK = one clock cycle at 27 MHz.
MODE 0
MODE 1
MODE 2
MODE 3
ADV7190/ADV7191
TR17
TR16
TR15
HSYNC TO PIXEL
DATA ADJUST
TR15 TR14
0 TPCLK
1 T PCLK
2 TPCLK
3 TPCLK
0
1
0
1
TR13
TR13 TR12
TC
0
1
TR12
TR11
HSYNC TO
VSYNC DELAY
HSYNC TO VSYNC
RISING EDGE DELAY
(MODE 1 ONLY)
TR17 TR16
0
0
1
1
TR14
0
0
1
1
TB
TB + 32s
HSYNC WIDTH
TB
TR11 TR10
0 TPCLK
4 T PCLK
8 TPCLK
18 TPCLK
0
1
0
1
TR10
0
0
1
1
TA
1 TPCLK
4 T PCLK
16 TPCLK
128 TPCLK
0
1
0
1
VSYNC WIDTH
(MODE 2 ONLY)
TR15 TR14
0
0
1
1
0
1
0
1
1 TPCLK
4 T PCLK
16 TPCLK
128 TPCLK
TIMING MODE 1 (MASTER/PAL)
LINE 1
HSYNC
LINE 313
LINE 314
TA
TC
TB
VSYNC
Figure 61. Timing Register 1
SUBCARRIER FREQUENCY REGISTERS 3–0
(FSC31–FSC0) (Address (SR4–SR0) = 0CH–0FH)
SUBCARRIER PHASE REGISTER (FPH7–FPH0)
(Address (SR4–SR0) = 10H)
These 8-bit-wide registers are used to set up the Subcarrier Frequency. The value of these registers are calculated by using the
following equation:
This 8-bit-wide register is used to set up the Subcarrier Phase.
Each bit represents 1.41°. For normal operation this register is
set to 00Hex.
(2
32
Subcarrier Frequency Register =
)
– 1 × f SCF
SUBCARRIER
PHASE
REGISTER
fCLK
FPH7
FPH6
FPH5
FPH4
FPH3
FPH2
FPH1
FPH0
Figure 63. Subcarrier Phase Register
Example: NTSC Mode, fCLK = 27 MHz, fSCF = 3.5795454 MHz
(2
Subcarrier Frequency Value =
32
)
– 1 × 3.5795454 × 106
27 × 106
Subcarrier Register Value = 21F07C16 Hex
Figure 62 shows how the frequency is set up by the four registers.
SUBCARRIER
FREQUENCY
REG 3
SUBCARRIER
FREQUENCY
REG 2
SUBCARRIER
FREQUENCY
REG 1
SUBCARRIER
FREQUENCY
REG 0
FSC31
FSC30
FSC29
FSC28
FSC27
FSC26
FSC25
FSC24
FSC23
FSC22
FSC21
FSC20
FSC19
FSC18
FSC17
FSC16
FSC15
FSC14
FSC13
FSC12
FSC11
FSC10
FSC9
FSC8
FSC7
FSC6
FSC5
FSC4
FSC3
FSC2
FSC1
FSC0
Figure 62. Subcarrier Frequency Registers
CLOSED CAPTIONING EVEN FIELD
DATA REGISTER 1–0 (CCD15–CCD0)
(Address (SR4–SR0) = 11–12H)
These 8-bit-wide registers are used to set up the closed captioning
extended data bytes on Even Fields. Figure 64 shows how the
high and low bytes are set up in the registers.
BYTE 1
BYTE 0
CCD15 CCD14
CCD7
CCD6
CCD13 CCD12 CCD11 CCD10
CCD5
CCD4
CCD3
CCD2
CCD9
CCD1
CCD8
CCD0
Figure 64. Closed Captioning Extended Data Register
CLOSED CAPTIONING ODD FIELD
DATA REGISTER 1–0 (CED15–CED0)
(Subaddress (SR4–SR0) = 13–14H)
These 8-bit-wide registers are used to set up the closed captioning
data bytes on Odd Fields. Figure 65 shows how the high and low
bytes are set up in the registers.
BYTE 1
BYTE 0
CED15
CED7
CED14
CED6
CED13
CED5
CED12
CED4
CED11
CED3
CED10
CED2
CED9
CED1
CED8
CED0
Figure 65. Closed Captioning Data Register
–36–
REV. 0
ADV7190/ADV7191
Bits TC07–TC04 are changed then the falling edge of TTREQ
will track that of the rising edge (i.e., the time between the falling and rising edge remains constant).
NTSC PEDESTAL/PAL TELETEXT CONTROL
REGISTERS 3–0
(PCE15–0, PCO15–0)/(TXE15–0, TXO15–0)
(Subaddress (SR4–SR0) = 15–18H)
PCLK = clock cycle at 27 MHz.
These 8-bit wide registers are used to enable the NTSC pedestal/
PAL Teletext on a line-by-line basis in the vertical blanking
interval for both odd and even fields. Figures 66 and 67 show
the four control registers. A Logic 1 in any of the bits of these
registers has the effect of turning the Pedestal OFF on the equivalent line when used in NTSC. A Logic 1 in any of the bits of
these registers has the effect of turning Teletext ON on the
equivalent line when used in PAL.
LINE 17 LINE 16
FIELD 1/3
FIELD 1/3
FIELD 2/4
FIELD 2/4
PCO7
PCO6
PCO5
PCO4
PCO3
PCO2
LINE 25 LINE 24 LINE 23
LINE 22 LINE 21 LINE 20
PCO12 PCO11 PCO10
PCO1
PCLK = clock cycle at 27 MHz.
TC07
LINE 19 LINE 18
PCO9
PCO8
LINE 15 LINE 14 LINE 13 LINE 12 LINE 11 LINE 10
PCE7
PCE5
PCE4
PCE3
PCE2
PCE1
LINE 25 LINE 24 LINE 23
LINE 22 LINE 21 LINE 20
PCE15
PCE12
PCE13
PCE11
LINE 14 LINE 13
FIELD 1/3
TXO7
TXO6
PCE10
FIELD 2/4
TXO5
TXO4
TXO3
PCE0
PCE9
LINE 8
LINE 7
TXO2
TXO1
TXO0
LINE 19 LINE 18 LINE 17
TXO15
TXO12
TXO14
TXE7
TXE6
TXO13
TXO10
TXO9
TXO8
LINE 12 LINE 11 LINE 10
LINE 9
LINE 8
LINE 7
TXE1
TXE0
TXE5
TXE4
TXE3
TXE2
LINE 19 LINE 18 LINE 17
TXE15
TXE12
TXE14
TXE13
TXE11
TC03
TC02
TC01
TC00
TTXREQ
FALLING EDGE CONTROL
TC03 TC02 TC01 TC00
0
0
0
0
0 PCLK
0
0
0
1
1 PCLK
''
''
''
''
'' PCLK
1
1
1
0
14 PCLK
1
1
1
1
15 PCLK
CGMS_WSS REGISTER 0 C/W0 (C/W07–C/W00)
(Address (SR4–SR0) = 19H)
CGMS_WSS register 0 is an 8-bit-wide register. Figure 69 shows
the operations under control of this register.
C/W0 BIT DESCRIPTION
CGMS Data (C/W00–C/W03)
LINE 16 LINE 15
TXO11
LINE 22 LINE 21 LINE 20
TC04
Figure 68. Teletext Control Register
PCE8
LINE 9
LINE 22 LINE 21 LINE 20
LINE 14 LINE 13
FIELD 2/4
LINE 12 LINE 11 LINE 10
TC05
LINE 19 LINE 18
Figure 66. Pedestal Control Registers
FIELD 1/3
TC06
TTXREQ
RISING EDGE CONTROL
TC07 TC06 TC05 TC04
0
0
0
0
0 PCLK
0
0
0
1
1 PCLK
''
''
''
''
'' PCLK
1
1
1
0
14 PCLK
1
1
1
1
15 PCLK
PCO0
LINE 17 LINE 16
PCE14
These bits control the position of the rising edge of TTXREQ.
It can be programmed from zero clock cycles to a maximum of 15
clock cycles.
LINE 15 LINE 14 LINE 13 LINE 12 LINE 11 LINE 10
PCO15 PCO14 PCO13
PCE6
TTXREQ Rising Edge Control (TC04–TC07)
These four data bits are the final four bits of CGMS data output stream. Note it is CGMS data ONLY in these bit positions,
i.e., WSS data does not share this location.
CGMS CRC Check Control (C/W04)
LINE 16 LINE 15
TXE10
TXE9
When this bit is enabled (1), the last six bits of the CGMS data,
i.e., the CRC check sequence, is internally calculated by the
ADV7190/ADV7191. If this bit is disabled (0), the CRC values
in the register are output to the CGMS data stream.
TXE8
Figure 67. Teletext Control Registers
TELETEXT REQUEST CONTROL REGISTER (TC07–TC00)
(Address (SR4–SR0) = 1CH)
CGMS Odd Field Control (C/W05)
Teletext Control Register is an 8-bit-wide register. See Figure 68.
When this bit is set (1), CGMS is enabled for odd fields. Note
this is only valid in NTSC mode.
TTXREQ Falling Edge Control (TC00–TC03)
CGMS Even Field Control (C/W06)
These bits control the position of the falling edge of TTXREQ.
It can be programmed from zero clock cycles to a maximum
of 15 clock cycles. This controls the active window for Teletext
data. Increasing this value reduces the amount of Teletext bits
below the default of 360. If Bits TC00–TC03 are 00Hex when
C/W07
C/W06
WSS CONTROL
C/W07
0
1
DISABLE
ENABLE
C/W05
WSS Control (C/W07)
When this bit is set (1), wide screen signalling is enabled. Note
this is only valid in PAL mode.
C/W04
CGMS ODD FIELD
CONTROL
C/W05
0
1
CGMS EVEN FIELD
CONTROL
C/W06
0
1
When this bit is set (1), CGMS is enabled for even fields. Note
this is only valid in NTSC mode.
DISABLE
ENABLE
C/W03
C/W02
C/W03 – C/W00
CGMS DATA
DISABLE
ENABLE
CGMS CRC CHECK
CONTROL
C/W04
0
1
DISABLE
ENABLE
Figure 69. CGMS_WSS Register 0
REV. 0
C/W01
–37–
C/W00
ADV7190/ADV7191
CGMS_WSS REGISTER 1 C/W1 (C/W17–C/W10)
(Address (SR4–SR0) = 1AH)
CC07
CC06
CC05
CGMS_WSS Register 1 is an 8-bit-wide register. Figure 70 shows
the operations under control of this register.
These bits are CGMS data bits only.
C/W14
C/W13
CC01
CC00
Figure 72. Contrast Control Register
CGMS Data (C/W16–C/W17)
C/W15
CC02
Y SCALE VALUE
These bit locations are shared by CGMS data and WSS data. In
NTSC mode these bits are CGMS data. In PAL mode these bits
are WSS data.
C/W16
CC03
CC07 – CC00
C/W1 BIT DESCRIPTION
CGMS/WSS Data (C/W10–C/W15)
C/W17
CC04
C/W12
C/W11
COLOR CONTROL REGISTERS 2–1 (CC2–CC1)
(Address (SR4–SR0) = 1EH–1FH)
The color control registers are 8-bit-wide registers used to scale
the U and V output levels. Figure 73 shows the operations under
control of these registers.
C/W10
CC17
CC16
CC15
CC14
CC13
C/W17 – C/W16
C/W15 – C/W10
CC17 – CC10
CGMS DATA
CGMS/WSS DATA
U SCALE VALUE
CC12
CC11
CC10
CC22
CC21
CC20
Figure 70. CGMS_WSS Register 1
CC27
CC26
CC25
CGMS_WSS REGISTER 2
C/W1 (C/W27–C/W20)
(Address (SR4–SR0) = 1BH)
CC27 – CC20
Figure 73. Color Control Registers
CC1 BIT DESCRIPTION
U Scale Value (CC10–CC17)
C/W2 BIT DESCRIPTION
CGMS/WSS Data (C/W20–C/W27)
These bit locations are shared by CGMS data and WSS data. In
NTSC mode these bits are CGMS data. In PAL mode these bits
are WSS data.
C/W26
C/W25
C/W24
CC23
V SCALE VALUE
CGMS_WSS Register 2 is an 8-bit-wide register. Figure 71 shows
the operations under control of this register.
C/W27
CC24
C/W23
C/W22
C/W21
C/W20
Scale Factor = 1.18
C/W27 – C/W20
U Scale Value = 1.18 × 128 = 151.04
U Scale Value = 151 (rounded to the nearest integer)
U Scale Value = 10010111b
U Scale Value = 97h
Figure 71. CGMS_WSS Register 2
CONTRAST CONTROL REGISTER (CC00–CC07)
(Address (SR4–SR0) = 1DH)
CC2 BIT DESCRIPTION
V Scale Value (CC20–CC27)
The contrast control register is an 8-bit-wide register used to
scale the Y output levels. Figure 72 shows the operation under
control of this register.
These eight bits represent the value required to scale the V pixel
data from 0.0 to 2.0 of its initial level. The value of these eight
bits is calculated using the following equation:
Y Scale Value (CC00–CC07)
These eight bits represent the value required to scale the Y pixel
data from 0.0 to 1.5 of its initial level. The value of these eight
bits is calculated using the following equation:
Example:
Scale Factor = 1.18
Y Scale Value = 1.18 × 128 = 151.04
Y Scale Value = 151 (rounded to the nearest integer)
Y Scale Value = 10010111b
Y Scale Value = 97h
U Scale Value = Scale Factor × 128
Example:
CGMS/WSS DATA
Y Scale Value = Scale Factor × 128
These eight bits represent the value required to scale the U level
from 0.0 to 2.0 of its initial level. The value of these eight bits is
calculated using the following equation:
V Scale Value = Scale Factor × 128
Example:
Scale Factor = 1.18
V Scale Value = 1.18 × 128 = 151.04
V Scale Value = 151 (rounded to the nearest integer)
V Scale Value = 10010111b
V Scale Value = 97h
–38–
REV. 0
ADV7190/ADV7191
HUE ADJUST CONTROL REGISTER (HCR)
(Address (SR5–SR0) = 20H)
The hue control register is an 8-bit-wide register used to adjust
BRIGHTNESS CONTROL REGISTERS (BCR)
(Address (SR5–SR0) = 21H)
The brightness register is an 8-bit-wide register which allows
brightness control. Figure 75 shows the operation under control
of this register.
the hue on the composite and chroma outputs. Figure 74 shows
the operation under control of this register.
HCR7
HCR6
HCR5
HCR4
HCR3
HCR2
HCR1
BCR BIT DESCRIPTION
Brightness Value (BCR0–BCR6)
HCR0
Seven bits of this 8-bit-wide register are used to control the
brightness level. The brightness is controlled by adding a programmable setup level onto the scaled Y data. This brightness
level can be a positive or negative value.
HCR7 – HCR0
HUE ADJUST VALUE
Figure 74. Hue Adjust Control Register
HCR Bit Description
Hue Adjust Value (HCR0–HCR7)
These eight bits represent the value required to vary the hue of
the video data, i.e., the variance in phase of the subcarrier during
active video with respect to the phase of the subcarrier during the
colorburst. The ADV7190/ADV7191 provides a range of ± 22.5°
increments of 0.17578125°. For normal operation (zero adjustment) this register is set to 80Hex. FFHex and 00Hex represent
the upper and lower limit (respectively) of adjustment attainable.
Hue Adjust [°] = 0.17578125° × (HCRd – 128); for positive Hue
Adjust Value
Example:
To adjust the hue by 4° write 97h to the Hue Adjust Control
Register:
(4/0.17578125) + 128 = 151d* = 97h
The programmable brightness level in NTSC without pedestal
and PAL are max 15 IRE and min –7.5 IRE, in NTSC with
pedestal max 22.5 IRE and min 0 IRE.
Table IV. Brightness Control Register Value
Setup
Level in
NTSC with
Pedestal
Setup
Level in
NTSC No
Pedestal
Setup
Level in
PAL
Brightness
Control
Register
Value
22.5 IRE
15 IRE
7.5 IRE
0 IRE
15 IRE
7.5 IRE
0 IRE
–7.5 IRE
15 IRE
7.5 IRE
0 IRE
–7.5 IRE
1Eh
0Fh
00h
71h
NOTE
Values in the range from 3F h to 44h might result in an invalid output signal.
To adjust the hue by (–4°) write 69h to the Hue Adjust Control
Register:
(–4/0.17578125) + 128 = 10dd* = 69h
*Rounded to the nearest integer.
EXAMPLE
1. Standard: NTSC with Pedestal. To add +20 IRE brightness level, write 28h into the Brightness Control Register:
[Brightness Control Register Value]h = [IRE Value ⫻ 2.015631]h = [20 × 2.015631]h = [40.31262]h = 28h
2. Standard: PAL. To add –7 IRE brightness level write 72h into the Brightness Control Register:
[|IRE Value| × 2.015631] = [7 × 2.015631] = [14.109417] = 0001110b
[0001110] into two’s complement = 1110010b = 72h
NTSC WITHOUT PEDESTAL
+7.5 IRE
100 IRE
0 IRE
–7.5 IRE
NO SETUP VALUE
ADDED
BCR7
BCR6
POSITIVE SETUP
VALUE ADDED
WRITE TO BRIGHTNESS
CONTROL REGISTER: 12h
BCR5
BCR4
BCR3
NEGATIVE SETUP
VALUE ADDED
WRITE TO BRIGHTNESS
CONTROL REGISTER: 6Eh
BCR2
BCR7
BCR6 – BCR0
ZERO MUST BE
WRITTEN TO
THIS BIT
BRIGHTNESS VALUE
BCR1
Figure 75. Brightness Control Register
REV. 0
–39–
BCR0
ADV7190/ADV7191
Sharpness CONTROL REGISTER (PR)
(Address (SR5–SR0) = 22H)
Figures 77 and 78 show the various operations under the control
of DNR Register 0.
The sharpness response register is an 8-bit-wide register. The
four MSBs are set to 0. The four LSBs are written to in order to
select a desired filter response. Figure 76 shows the operation
under control of this register.
DNR07
DNR06
DNR05
DNR04
DNR03
CORING GAIN DATA
0
0
0
0
0
0
0
0
1
These four bits are used to select the desired luma filter response.
The option of twelve responses is given supporting a gain boost/
attenuation in the range –4 dB to +4 dB. The value 12 (1100)
written to these four bits corresponds to a boost of +4 dB while
the value 0 (0000) corresponds to –4 dB. For normal operation
these four bits are set to 6 (0110).
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
DNR01
DNR00
CORING GAIN BORDER
DNR DNR DNR DNR
07 06 05 04
PR BIT DESCRIPTION
Sharpness Response Value (PR3–PR0)
DNR02
DNR DNR DNR DNR
03 02 01 00
0
1/16
2/16
3/16
4/16
5/16
6/16
7/16
8/16
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0
1/16
2/16
3/16
4/16
5/16
6/16
7/16
8/16
Figure 77. DNR Register 0 in Sharpness Mode
Note: Luma Filter Select has to be set to Extended Mode and
Sharpness Filter Enable Control has to be enabled for settings
in the Sharpness Control Register to take effect (MR02–04 =
100; MR74 = 1). See Internal Filter Response section.
DNR07
DNR06
DNR05
DNR04
DNR03
DNR02
DNR01
DNR00
Reserved (PR4–PR7)
CORING GAIN DATA
A Logic 0 must be written to these bits.
CORING GAIN BORDER
DNR DNR DNR DNR
07 06 05 04
PR7
PR6
PR5
PR4
PR3
PR2
PR1
PR7 – PR4
PR3 – PR0
ZERO MUST BE
WRITTEN TO
THESE BITS
SHARPNESS
RESPONSE VALUE
PR0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
DNR DNR DNR DNR
03 02 01 00
0
1/8
2/8
3/8
4/8
5/8
6/8
7/8
1
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0
1/8
2/8
3/8
4/8
5/8
6/8
7/8
1
Figure 76. Sharpness Control Register
Figure 78. DNR Register 0 in DNR Mode
DNR REGISTERS 2–0
(DNR 2–DNR 0)
(Address (SR5–SR0) = 23H–25H)
DNR1 BIT DESCRIPTION
DNR Threshold (DNR10–DNR15)
The Digital Noise Reduction Registers are three 8-bit wide
register. They are used to control the DNR processing. See
Digital Noise Reduction section.
These six bits are used to define the threshold value in the range
of 0 to 63. The range is an absolute value.
Coring Gain Border (DNR00–DNR03)
In setting DNR16 to a Logic 1 the block transition area can be
defined to consist of four pixels. If this bit is set to a Logic 0 the
border transition area consists of two pixels, where one pixel
refers to two clock cycles at 27 MHz.
Border Area (DNR16)
These four bits are assigned to the gain factor applied to border
areas.
In DNR Mode the range of gain values is 0–1, in increments of
1/8. This factor is applied to the DNR filter output which lies
below the set threshold range. The result is then subtracted
from the original signal.
In DNR Sharpness Mode the range of gain values is 0–0.5, in
increments of 1/16. This factor is applied to the DNR filter output which lies above the threshold range.
Block Size Control (DNR17)
This bit is used to select the size of the data blocks to be processed
(see Figure 79). Setting the block size control function to a
Logic 1 defines a 16 × 16 pixel data block, a Logic 0 defines an
8 × 8 pixel data block, where one pixel refers to two clock cycles
at 27 MHz.
The result is added to the original signal.
720 485 PIXELS
(NTSC)
Coring Gain Data (DNR04–DNR07)
2 PIXEL
BORDER DATA
These four bits are assigned to the gain factor applied to the luma
data inside the MPEG pixel block.
In DNR Mode the range of gain values is 0–1, in increments of
1/8. This factor is applied to the DNR filter output which lies
below the set threshold range. The result is then subtracted
from the original signal.
In DNR Sharpness Mode the range of gain values is 0–0.5, in
increments of 1/16. This factor is applied to the DNR filter output which lies above the threshold range. The result is added to
the original signal.
–40–
88
88
PIXEL BLOCK PIXEL BLOCK
Figure 79. MPEG Block Diagram
REV. 0
ADV7190/ADV7191
DNR17
BLOCK SIZE
CONTROL
DNR17
0
1
DNR16
DNR15
DNR14
DNR13
DNR10
DNR DNR DNR DNR DNR DNR
15 14 13 12 11 10
DNR16
0
1
DNR11
DNR THRESHOLD
BORDER AREA
8 PIXELS
16 PIXELS
DNR12
2 PIXELS
4 PIXELS
0
0
•
•
•
1
1
0
0
•
•
•
1
1
0
0
•
•
•
1
1
0
0
•
•
•
1
1
0
0
•
•
•
1
1
0
1
•
•
•
0
1
0
1
•
•
•
62
63
Figure 80. DNR Register 1
DNR2 BIT DESCRIPTION
DNR Input Select (DNR20–DNR22)
GAIN CONTROL
BLOCK SIZE CONTROL
BORDER AREA
BLOCK OFFSET
GAIN
CORING GAIN DATA
CORING GAIN BORDER
DNR
MODE
Three bits are assigned to select the filter which is applied to the
incoming Y data. The signal which lies in the passband of the
selected filter is the signal which will be DNR processed. Figure
81 shows the filter responses selectable with this control.
NOISE SIGNAL PATH
FILTER BLOCK
1
MAGNITUDE – dB
0.8
FILTER OUTPUT
< THRESHOLD ?
Y DATA
INPUT
FILTER D
FILTER OUTPUT
> THRESHOLD
FILTER C
0.6
MAIN SIGNAL PATH
0.4
FILTER B
DNR
SHARPNESS
MODE
0.2
FILTER A
0
1
2
3
4
FREQUENCY – MHz
5
6
FILTER BLOCK
Figure 81. Filter Response of Filters Selectable
FILTER OUTPUT
> THRESHOLD ?
Y DATA
INPUT
DNR Mode Control (DNR23)
FILTER OUTPUT
< THRESHOLD
This bit controls the DNR mode selected. A Logic 0 selects
DNR mode, a Logic 1 selects DNR Sharpness mode.
MAIN SIGNAL PATH
DNR works on the principle of defining low amplitude, highfrequency signals as probable noise and subtracting this noise
from the original signal.
DNR
OUT
GAIN CONTROL
BLOCK SIZE CONTROL
BORDER AREA
BLOCK OFFSET
GAIN
CORING GAIN DATA
CORING GAIN BORDER
NOISE SIGNAL PATH
0
SUBTRACT
SIGNAL IN
THRESHOLD
RANGE
FROM
ORIGINAL
SIGNAL
ADD
SIGNAL
ABOVE
THRESHOLD
RANGE
TO
ORIGINAL
SIGNAL
DNR
OUT
Figure 82. Block Diagram for DNR Mode and DNR Sharpness Mode
Block Offset (DNR24–DNR27)
In DNR mode, it is possible to subtract a fraction of the signal
which lies below the set threshold, assumed to be noise, from
the original signal. The threshold is set in DNR Register 1.
When DNR Sharpness mode is enabled it is possible to add a
fraction of the signal that lies above the set threshold to the
original signal, since this data is assumed to be valid data and
not noise. The overall effect being that the signal will be boosted
(similar to using Extended SSAF Filter).
Four bits are assigned to this control which allows a shift of the
data block of 15 pixels maximum. Consider the coring gain positions fixed. The block offset shifts the data in steps of one pixel
such that the border coring gain factors can be applied at the same
position regardless of variations in input timing of the data.
APPLY DATA
CORING GAIN
DNR27 – DNR24
= 01 HEX
APPLY BORDER
CORING GAIN
O X X X X X X O
O X X X X X X O
O X X X X X X O
O X X X X X X O
O X X X X X X O
O X X X X X X O
OFFSET
CAUSED BY
VARIATIONS IN
INPUT TIMING
Figure 83. DNR27–DNR24, Block Offset Control
REV. 0
–41–
ADV7190/ADV7191
DNR27
DNR26
DNR25
DNR24
DNR23
DNR MODE
CONTROL
BLOCK OFFSET
DNR DNR DNR DNR
27 26 25 24
0
0
0
•
•
•
1
1
1
0
0
0
•
•
•
1
1
1
0
0
1
•
•
•
0
1
1
0
1
0
•
•
•
1
0
1
DNR22
0 PIXEL OFFSET
1 PIXEL OFFSET
2 PIXEL OFFSET
•
•
•
13 PIXEL OFFSET
14 PIXEL OFFSET
15 PIXEL OFFSET
DNR21
DNR20
DNR INPUT SELECT
DNR DNR DNR
22 21 20
DNR23
0
DNR MODE
1
DNR
SHARPNESS
MODE
0
0
0
1
0
1
1
0
1
0
1
0
FILTER A
FILTER B
FILTER C
FILTER D
Figure 84. DNR Register 2
y96 = [(80/224)0.5 × 224] + 16 = 150*
y128 = [(112/224)0.5 × 224] + 16 = 174*
GAMMA CORRECTION REGISTERS 0–13
(GAMMA CORRECTION 0–13)
(Address (SR5–SR0) = 26H–32H)
*Rounded to the nearest integer.
The Gamma Correction Registers are fourteen 8-bit-wide registers. They are used to program the gamma correction Curves A
and B.
The above will result in a gamma curve shown below, assuming
a ramp signal as an input.
Gamma correction is applied to compensate for the nonlinear
relationship between signal input and brightness level output (as
perceived on the CRT). It can also be applied wherever nonlinear processing is used.
300
GAMMA–CORRECTED AMPLITUDE
GAMMA CORRECTION BLOCK OUTPUT
TO A RAMP INPUT
Gamma correction uses the function:
SignalOUT =
(SignalIN )γ
where
γ = gamma power factor
Gamma correction is performed on the luma data only. The
user has the choice to use two different curves, Curve A, or
Curve B. At any one time only one of these curves can be used.
SIGNAL OUTPUT
200
250
0.5
150 200
150
100
100
SIGNAL INPUT
50
0
0
50
100
150
LOCATION
200
250
Figure 85. Signal Input (Ramp) and Signal Output for
Gamma 0.5
Values at Location 0, 16, 240, and 255 are fixed and cannot be
changed.
300
GAMMA CORRECTION BLOCK OUTPUT
TO A RAMP INPUT FOR VARIOUS GAMMA VALUES
GAMMA–CORRECTED AMPLITUDE
For the length of 16 to 240 the gamma correction curve has to
be calculated as below:
y = xγ
where
y = gamma corrected output
x = linear input signal
γ = gamma power factor
To program the gamma correction registers, the seven values for
y have to be calculated using the following formula:
γ
yn = [x(n–16) /(240–16) ] × (240–16) + 16
where
Example:
300
50
The response of the curve is programmed at seven predefined
locations. In changing the values at these locations the gamma
curve can be modified. Between these points linear interpolation
is used to generate intermediate values. Considering the curve
to have a total length of 256 points, the seven locations are at:
32, 64, 96, 128, 160, 192, and 224.
x(n-16) = Value for x along x-axis
yn
= Value for y along the y-axis, which has to be written
into the gamma correction register
n
= 32, 64, 96, 128, 160, 192, or 224
250
250
SIGNAL OUTPUTS
200
0.3
0.5
150
T
PU
IN
L
A
1.5
GN
SI
100
1.8
50
0
0
50
100
150
LOCATION
200
250
Figure 86. Signal Input (Ramp) and Selectable Gamma
Output Curves
The gamma curves shown above are examples only, any userdefined curve is acceptable in the range of 16–240.
y32 = [(16/224)0.5 × 224] + 16 = 76*
y64 = [(48/224)0.5 × 224] + 16 =120*
–42–
REV. 0
ADV7190/ADV7191
BRIGHTNESS DETECT REGISTER
(Address (SR5–SR0) = 34H)
The Brightness Detect Register is an 8-bit-wide register used only
OCR BIT DESCRIPTION
to read back data in order to monitor the brightness/darkness of
the incoming video data on a field-by-field basis. The brightness
information is read from the I2C and based on this information,
the color controls or the gamma correction controls may be
adjusted.
CLKOUT Pin Control (OCR01)
Reserved (OCR00)
A Logic 0 must be written to this bit.
This bit enables the CLKOUT pin when set to 1 and, therefore,
outputs a 54 MHz clock generated by the internal PLL. The
PLL and 4× Oversampling have to be enabled for this control to
take effect, (MR61 = 0; MR16 = 1).
The luma data is monitored in the active video area only. The
average brightness I2C register is updated on the falling edge of
every VSYNC signal.
Reserved (OCR02–03)
A Logic 0 must be written to these bits.
Reserved (OCR04–06)
A Logic 1 must be written to these bits.
OUTPUT CLOCK REGISTER (OCR 9–0)
Reserved (OCR07)
(Address (SR4–SR0) = 35H)
The Output Clock Register is a 8-bit-wide register. Figure 87
A Logic 0 must be written to this bit.
shows the various operations under the control of this register.
OCR07
OCR06
OCR05
OCR04
OCR03
OCR02
OCR01
OCR00
OCR07
OCR06 – OCR04
OCR03 – OCR02
OCR00
ZERO MUST BE
WRITTEN TO
THIS BIT
ONE MUST BE
WRITTEN TO
THESE BITS
ZERO MUST BE
WRITTEN TO
THESE BITS
ZERO MUST BE
WRITTEN TO
THIS BIT
CLKOUT
PIN CONTROL
OCR01
0
ENSABLED
1
DISABLED
Figure 87. Output Clock Register (OCR)
REV. 0
–43–
ADV7190/ADV7191
APPENDIX 1
BOARD DESIGN AND LAYOUT CONSIDERATIONS
The ADV7190/ADV7191 is a highly integrated circuit containing both precision analog and high-speed digital circuitry. It
has been designed to minimize interference effects on the integrity of the analog circuitry by the high-speed digital circuitry. It
is imperative that these same design and layout techniques be
applied to the system-level design such that high-speed, accurate
performance is achieved. The Recommended Analog Circuit Layout shows the analog interface between the device and monitor.
Supply Decoupling
The layout should be optimized for lowest noise on the ADV7190/
ADV7191 power and ground lines by shielding the digital inputs
and providing good decoupling. The lead length between groups
of VAA and GND pins should by minimized in order to minimize inductive ringing.
It is important to note that while the ADV7190/ADV7191
contains circuitry to reject power supply noise, this rejection
decreases with frequency. If a high-frequency switching power
supply is used, the designer should pay close attention to reducing
power supply noise and consider using a three-terminal voltage
regulator for supplying power to the analog power plane.
Ground Planes
The ground plane should encompass all ADV7190/ADV7191
ground pins, voltage reference circuitry, power supply bypass circuitry for the ADV7190/ADV7191 , the analog output traces, and
all the digital signal traces leading up to the ADV7190/ADV7191.
This should be as substantial as possible to maximize heat spreading and power dissipation on the board.
Digital Signal Interconnect
The digital inputs to the ADV7190/ADV7191 should be isolated
as much as possible from the analog outputs and other analog
circuitry. Also, these input signals should not overlay the analog power plane.
Due to the high clock rates involved, long clock lines to the
ADV7190/ADV7191 should be avoided to reduce noise pickup.
Power Planes
The ADV7190/ADV7191 and any associated analog circuitry
should have its own power plane, referred to as the analog power
plane (VAA). This power plane should be connected to the
regular PCB power plane (VCC) at a single point through a
ferrite bead. This bead should be located within three inches
of the ADV7190/ADV7191.
The metallization gap separating device power plane and board
power plane should be as narrow as possible to minimize the
obstruction to the flow of heat from the device into the general
board.
Any active termination resistors for the digital inputs should be
connected to the regular PCB power plane (VCC), and not the
analog power plane.
Analog Signal Interconnect
The ADV7190/ADV7191 should be located as close as possible
to the output connectors to minimize noise pickup and reflections due to impedance mismatch.
The video output signals should overlay the ground plane, and
not the analog power plane, to maximize the high frequency power
supply rejection.
The PCB power plane should provide power to all digital logic
on the PC board, and the analog power plane should provide
power to all ADV7190/ADV7191 power pins and voltage reference
circuitry.
Plane-to-plane noise coupling can be reduced by ensuring that
portions of the regular PCB power and ground planes do not
overlay portions of the analog power plane, unless they can be
arranged so the plane-to-plane noise is common-mode.
For optimum performance, bypass capacitors should be installed
using the shortest leads possible, consistent with reliable operation,
to reduce the lead inductance. Best performance is obtained
with 0.1 µF ceramic capacitor decoupling. Each group of VAA
pins on the ADV7190/ADV7191 must have at least one 0.1 µF
decoupling capacitor to GND. These capacitors should be placed
as close as possible to the device.
Digital inputs, especially pixel data inputs and clocking signals
should never overlay any of the analog signal circuitry and should
be kept as far away as possible.
For best performance, the outputs should each have a 300 Ω load
resistor connected to GND. These resistors should be placed as
close as possible to the ADV7190/ADV7191 so as to minimize
reflections.
The ADV7190/ADV7191 should have no inputs left floating.
Any inputs that are not required should be tied to ground.
–44–
REV. 0
ADV7190/ADV7191
APPENDIX 1
BOARD LAYOUT
POWER SUPPLY DECOUPLING
FOR EACH POWER SUPPLY GROUP
5V (VAA)
10nF
5V (VAA)
0.1F
17, 25,
29, 38,
43, 54, 63
5V (VAA)
VAA
0.1F
COMP1
DAC A
COMP2
300
VREF
DAC B
P0
ADV7190/
ADV7191
P15
300
DAC C
VSO/CLAMP
DAC D
300
PAL_NTSC
SCRESET/RTC/TR
DAC E
300
HSYNC
VSYNC
5V (VAA)
5V (VAA)
300
100
4.7F
6.3V
5V (VAA)
27MHz CLOCK
(SAME CLOCK AS
USED BY MPEG2
DECODER)
DAC F
BLANK
4.7k
CONNECT DAC OUTPUTS
TO OPTIONAL OUTPUT FILTER
AND BUFFER CIRCUIT
300
CSO_HSO
UNUSED
INPUTS
SHOULD BE
GROUNDED
0.1F
4.7k
RESET
SCL
TTX
SDA
100
TTXREQ
RSET2
CLKIN
RSET1
ALSB
5k
CLKOUT AGND
1.2k
1.2k
18, 24, 26,
33, 39, 42,
55, 64
Figure 88. Recommended Analog Circuit Layout
REV. 0
–45–
5V (VAA)
5k
MPU BUS
ADV7190/ADV7191
APPENDIX 2
CLOSED CAPTIONING
The ADV7190/ADV7191 supports closed captioning conforming
to the standard television synchronizing waveform for color
transmission. Closed captioning is transmitted during the
blanked active line time of Line 21 of the odd fields and Line
284 of even fields.
Closed captioning consists of a seven-cycle sinusoidal burst
that is frequency and phase locked to the caption data. After the
clock run-in signal, the blanking level is held for two data bits
and is followed by a Logic Level 1 start bit. Sixteen bits of data
follow the start bit. These consist of two eight-bit bytes, seven
data bits, and one odd parity bit. The data for these bytes is
stored in Closed Captioning Data Registers 0 and 1.
The ADV7190/ADV7191 also supports the extended closed
captioning operation that is active during even fields and is
encoded on Scan Line 284. The data for this operation is stored
in Closed Captioning Extended Data Registers 0 and 1.
All clock run-in signals and timing to support closed captioning on
Lines 21 and 284 are generated automatically by the ADV7190/
ADV7191 All pixel inputs are ignored during Lines 21 and 284
if closed captioning is enabled.
10.5 0.25s
FCC Code of Federal Regulations (CFR) 47 Section 15.119
and EIA608 describe the closed captioning information for Lines
21 and 284.
The ADV7190/ADV7191 uses a single buffering method. This
means that the closed captioning buffer is only one byte deep,
therefore there will be no frame delay in outputting the closed
captioning data, unlike other two byte deep buffering systems.
The data must be loaded one line before (Line 20 or Line 283)
it is outputted on Line 21 and Line 284. A typical implementation
of this method is to use VSYNC to interrupt a microprocessor,
which in turn, will load the new data (two bytes) every field. If
no new data is required for transmission, 0s must be inserted
in both data registers, this is called NULLING. It is also
important to load control codes, all of which are double bytes
on Line 21, or a TV will not recognize them. If there is a message like Hello World, which has an odd number of characters, it
is important to pad it out to even in order to get end of caption
2-byte control code to land in the same field.
12.91s
7 CYCLES
OF 0.5035 MHz
(CLOCK RUN-IN)
TWO 7-BIT + PARITY
ASCII CHARACTERS
(DATA)
S
T
A
R
T
50 IRE
P
A
R
I
T
Y
D0–D6
BYTE 0
D0–D6
P
A
R
I
T
Y
BYTE 1
40 IRE
REFERENCE COLOR BURST
(9 CYCLES)
FREQUENCY = FSC = 3.579545MHz
AMPLITUDE = 40 IRE
10.003s
33.764s
27.382s
Figure 89. Closed Captioning Waveform (NTSC)
–46–
REV. 0
ADV7190/ADV7191
APPENDIX 3
COPY GENERATION MANAGEMENT SYSTEM (CGMS)
Function of CGMS Bits
The ADV7190/ADV7191 supports Copy Generation Management
System (CGMS) conforming to the standard. CGMS data is
transmitted on Line 20 of the odd fields and Line 283 of even
fields. Bits C/W05 and C/W06 control whether or not CGMS
data is outputed on ODD and EVEN fields. CGMS data can
only be transmitted when the ADV7190/ADV7191 is configured in
NTSC mode. The CGMS data is 20 bits long, the function of
each of these bits is as shown below. The CGMS data is preceded
by a reference pulse of the same amplitude and duration as a
CGMS bit, see Figure 94. These bits are outputed from the configuration registers in the following order: C/W00 = C16, C/W01 =
C17, C/W02 = C18, C/W03 = C19, C/W10 = C8, C/W11 =
C9, C/W12 = C10, C/W13 = C11, C/W14 = C12, C/W15 =
C13, C/W16 = C14, C/W17 = C15, C/W20 = C0, C/W21 = C1,
C/W22 = C2, C/W23 = C3, C/W24 = C4, C/W25 = C5, C/W26
= C6, C/W27 = C7. If the bit C/W04 is set to a Logic 1, the last six
bits C19–C14 which comprise the 6-bit CRC check sequence are
calculated automatically on the ADV7190/ADV7191 based on
the lower 14 bits (C0–C13) of the data in the data registers and
output with the remaining 14-bits to form the complete 20-bits of
the CGMS data. The calculation of the CRC sequence is based on
the polynomial X6 + X + 1 with a preset value of 111111. If C/W04
is set to a Logic 0, all 20 bits (C0–C19) are output directly from
the CGMS registers (no CRC calculated, must be calculated
by the user).
Word 0 – 6 Bits
Word 1 – 4 Bits
Word 2 – 6 Bits
CRC – 6 Bits CRC Polynomial = X6 + X + 1 (Preset to
111111)
WORD 0
B1
B2
B3
Aspect Ratio
Display Format
Undefined
WORD 0
B4, B5, B6
WORD 1
B7, B8, B9,
B10
WORD 2
B11, B12,
B13, B14
1
16:9
Letterbox
Identification Information About Video and
Other Signals (e.g., Audio)
Identification Signal Incidental to Word 0
Identification Signal and Information
Incidental to Word 0
100 IRE
CRC SEQUENCE
REF
70 IRE
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19
0 IRE
49.1s 0.5s
–40 IRE
11.2s
2.235s 20ns
Figure 90. CGMS Waveform Diagram
REV. 0
–47–
0
4:3
Normal
ADV7190/ADV7191
APPENDIX 4
WIDE SCREEN SIGNALING
The ADV7190/ADV7191 supports Wide Screen Signaling (WSS)
conforming to the standard. WSS data is transmitted on Line 23.
WSS data can only be transmitted when the ADV7190/ADV7191
is configured in PAL mode. The WSS data is 14-bits long, the
function of each of these bits is as shown below. The WSS data
is preceded by a run-in sequence and a Start Code, see Figure 91.
The bits are output from the configuration registers in the
following order: C/W20 = W0, C/W21 = W1, C/W22 = W2,
C/W23 = W3, C/W24 = W4, C/W25 = W5, C/W26 = W6,
C/W27 = W7, C/W10 = W8, C/W11 = W9, C/W12 = W10,
C/W13 = W11, C/W14 = W12, C/W15 = W13. If the bit
C/W07 is set to a Logic 1, it enables the WSS data to be transmitted on Line 23. The latter portion of Line 23 (42.5 µs from
the falling edge of HSYNC) is available for the insertion of video.
Function of CGMS Bits
Bit 0–Bit 2
Bit 3
B0,
0
1
0
1
0
1
0
1
B1,
0
0
1
1
0
0
1
1
Aspect Ratio/Format/Position
Is Odd Parity Check of Bit 0–Bit 2
B2,
0
0
0
0
1
1
1
1
B3
1
0
0
1
0
1
1
0
Aspect
Ratio
4:3
14:9
14:9
16:9
16:9
>16:9
14:9
16:9
Format
Full Format
Letterbox
Letterbox
Letterbox
Letterbox
Letterbox
Full Format
Nonapplicable
Position
Nonapplicable
Center
Top
Center
Top
Center
Center
Nonapplicable
B4
0
1
Camera Mode
Film Mode
B5
0
1
Standard Coding
Motion Adaptive Color Plus
B6
0
1
No Helper
Modulated Helper
B7
RESERVED
B9
0
1
0
1
B10
0
0
1
1
No Open Subtitles
Subtitles in Active Image Area
Subtitles Out of Active Image Area
RESERVED
B11
0
No Surround Sound Information
1
Surround Sound Mode
B12 RESERVED
B13 RESERVED
500mV
W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 W10 W11 W12 W13
RUN-IN
SEQUENCE
START
CODE
ACTIVE
VIDEO
11.0s
38.4s
42.5s
Figure 91. WSS Waveform Diagram
–48–
REV. 0
ADV7190/ADV7191
APPENDIX 5
TELETEXT INSERTION
Time, tPD, is the time needed by the ADV7190/ADV7191 to
interpolate input data on TTX and insert it onto the CVBS
or Y outputs, such that it appears tSYNTTXOUT = 10.2 µs after the
leading edge of the horizontal signal. Time, TTXDEL, is the pipeline delay time by the source that is gated by the TTXREQ signal
in order to deliver TTX data.
Teletext Protocol
With the programmability that is offered with TTXREQ signal
on the Rising/Falling edges, the TTX data is always inserted at
the correct position of 10.2 µs after the leading edge of Horizontal
Sync pulse, which enables a source interface with variable pipeline delays.
Thus 37 TTX bits correspond to 144 clocks (27 MHz), each bit
has a width of almost four clock cycles. The ADV7190/ADV7191
uses an internal sequencer and variable phase interpolation filter
to minimize the phase jitter and thus generate a bandlimited
signal which can be output on the CVBS and Y outputs.
The width of the TTXREQ signal must always be maintained
so it allows the insertion of 360 (in order to comply with the
Teletext Standard PAL-WST) teletext bits at a text data rate of
6.9375 Mbits/s. This is achieved by setting TC03–TC00 to 0.
The insertion window is not open if the Teletext Enable bit
(MR34) is set to 0.
At the TTX input the bit duration scheme repeats after every
37 TTX bits or 144 clock cycles. The protocol requires that
TTX Bits 10, 19, 28, 37 are carried by three clock cycles, all
other bits by four clock cycles. After 37 TTX bits, the next bits
with three clock cycles are Bits 47, 56, 65, and 74. This scheme
holds for all following cycles of 37 TTX bits, until all 360 TTX
bits are completed. All teletext lines are implemented in the
same way. Individual control of teletext lines are controlled
by Teletext Setup Registers.
The relationship between the TTX bit clock (6.9375 MHz) and
the system CLOCK (27 MHz) for 50 Hz is given as follows:
(27 MHz/4) = 6.75 MHz
(6.9375 × 106/6.75 × 106 = 1.027777
45 BYTES (360 BITS) – PAL
TELETEXT VBI LINE
ADDRESS & DATA
RUN-IN CLOCK
Figure 92. Teletext VBI Line
tSYNTTXOUT
CVBS/Y
tPD
HSYNC
tPD
10.2s
TTXDATA
TTXDEL
TTXREQ
PROGRAMMABLE PULSE EDGES
TTXST
tSYNTTXOUT = 10.2s
tPD = PIPELINE DELAY THROUGH ADV7190/ADV7191
TTXDEL = TTXREQ TO TTX (PROGRAMMABLE RANGE = 4 BITS [0–15 CLOCK CYCLES])
Figure 93. Teletext Functionality Diagram
REV. 0
–49–
ADV7190/ADV7191
APPENDIX 6
OPTIONAL OUTPUT FILTER
If an output filter is required for the CVBS, YUV, Chroma, and
RGB outputs of the ADV7190/ADV7191, the filter in Figure
94 can be used in 2× Oversampling Mode. Figure 96 shows a
filter that can be used in 4× Oversampling Mode. The plot of
the filter characteristics are shown in Figures 95 and 97. An output
2.5H
filter is not required if the outputs of the ADV7190/ADV7191
are connected to most analog monitors, or TVs; however, if
the output signals are applied to a system where sampling is
used (e.g., Digital TVs), a filter is required to prevent aliasing.
0.82H
2.2H
FILTER O/P
FILTER I/P
FILTER I/P
FILTER O/P
470pF
470pF
Figure 94. Output Filter for 2 × Oversampling Mode
Figure 96. Output Filter for 4 × Oversampling Mode
50
20
0
AMPLITUDE – dB
AMPLITUDE – dB
0
–50
–20
–40
–60
–100
–80
–150
100k
1.0M
10M
FREQUENCY – Hz
100M
–100
100k
1.0G
Figure 95. Output Filter Plot for 2 × Oversampling Filter
1.0M
10M
FREQUENCY – Hz
100M
1.0G
Figure 97. Output Filter Plot for 4 × Oversampling Filter
2 FILTER
REQUIREMENTS
4 FILTER
REQUIREMENTS
6.75
13.5
27.0
FREQUENCY – MHz
40.5
54.0
Figure 98. Output Filter Requirements in 4 × Oversampling Mode
–50–
REV. 0
ADV7190/ADV7191
APPENDIX 7
DAC BUFFERING
External buffering is needed on the ADV7190/ADV7191 DAC
outputs. The configuration in Figure 99 is recommended.
+VCC
4
When calculating absolute output full-scale current and voltage
use the following equations:
INPUT/
OPTIONAL
FILTER O/P
VOUT = IOUT × RLOAD
ADV7190/ADV7191
PIXEL
PORT
DAC A
OUTPUT
BUFFER
CVBS
DAC B
OUTPUT
BUFFER
LUMA
DAC C
OUTPUT
BUFFER
CHROMA
DAC D
OUTPUT
BUFFER
G
DAC E
OUTPUT
BUFFER
B
DAC F
OUTPUT
BUFFER
R
DIGITAL
CORE
RSET2
1.2k
Figure 99. Output DAC Buffering Configuration
REV. 0
OUTPUT TO
TV MONITOR
2
Figure 100. Recommended DAC Output Buffer Using an
Op Amp
VAA
RSET1
1
NOTE: ALTERNATELY THE AD8051 OP AMP CAN BE USED
K = 4.2146 constant, VREF = 1.235 V
1.2k
AD8051
3
–VCC
IOUT = (VREF × K)/RSET
VREF
5
–51–
ADV7190/ADV7191
APPENDIX 8
RECOMMENDED REGISTER VALUES
The ADV7190/ADV7191 registers can be set depending on the user standard required. The following examples give the various
register formats for several video standards.
PAL B, D, G, H, I (FSC = 4.43361875 MHz)
NTSC (FSC = 3.5795454 MHz)
Address
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
35Hex
Data
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Output Clock Register
10Hex
3FHex
62Hex
00Hex
00Hex
00Hex
00Hex
00Hex
04Hex
00Hex
08Hex
00Hex
16Hex
7CHex
F0Hex
21Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
44Hex
20Hex
00Hex
70Hex
Address
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
35Hex
–52–
Data
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR0
DNR1
DNR2
Output Clock Register
11Hex
3FHex
62Hex
00Hex
00Hex
00Hex
00Hex
00Hex
04Hex
00Hex
08Hex
00Hex
CBHex
8AHex
09Hex
2AHex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
44Hex
20Hex
00Hex
70Hex
REV. 0
ADV7190/ADV7191
PAL 60 (FSC = 4.43361875 MHz)
PAL N (FSC = 4.43361875 MHz)
Address
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
35Hex
REV. 0
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Output Clock Register
Data
Address
13Hex
3FHex
62Hex
00Hex
00Hex
00Hex
00Hex
00Hex
04Hex
00Hex
08Hex
00Hex
CBHex
8AHex
09Hex
2AHex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
44Hex
20Hex
00Hex
70Hex
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
35Hex
–53–
Data
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Output Clock Register
12Hex
3FHex
62Hex
00Hex
00Hex
00Hex
00Hex
00Hex
04Hex
00Hex
08Hex
00Hex
CBHex
8AHex
09Hex
2AHex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
44Hex
20Hex
00Hex
70Hex
ADV7190/ADV7191
PAL M (FSC = 3.57561149 MHz)
Address
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
EHex
0FHex
10Hex
11Hex
12Hex
13Hex
Data
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
12Hex
3FHex
62Hex
00Hex
00Hex
00Hex
00Hex
00Hex
04Hex
00Hex
08Hex
00Hex
A3Hex
EFHex
E6Hex
21Hex
00Hex
00Hex
00Hex
00Hex
Address
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
35Hex
–54–
Data
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Output Clock Register
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
44Hex
20Hex
00Hex
70Hex
REV. 0
ADV7190/ADV7191
POWER-ON RESET REGISTER VALUES
POWER-ON RESET REG VALUES
(PAL_NTSC = 0, NTSC Selected)
Address
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
26Hex
27Hex
28Hex
29Hex
2AHex
2BHex
2CHex
2DHex
2EHex
2FHex
30Hex
31Hex
32Hex
33Hex
34Hex
35Hex
REV. 0
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Gamma 0
Gamma 1
Gamma 2
Gamma 3
Gamma 4
Gamma 5
Gamma 6
Gamma 7
Gamma 8
Gamma 9
Gamma 10
Gamma 11
Gamma 12
Gamma 13
Brightness Detect Register
Output Clock Register
POWER-ON RESET REG VALUES
(PAL_NTSC = 1, PAL Selected)
Data
Address
00Hex
07Hex
08Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
08Hex
00Hex
16Hex
7CHex
F0Hex
21Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
72Hex
00Hex
01Hex
02Hex
03Hex
04Hex
05Hex
06Hex
07Hex
08Hex
09Hex
0AHex
0BHex
0CHex
0DHex
0EHex
0FHex
10Hex
11Hex
12Hex
13Hex
14Hex
15Hex
16Hex
17Hex
18Hex
19Hex
1AHex
1BHex
1CHex
1DHex
1EHex
1FHex
20Hex
21Hex
22Hex
23Hex
24Hex
25Hex
26Hex
27Hex
28Hex
29Hex
2AHex
2BHex
2CHex
2DHex
2EHex
2FHex
30Hex
31Hex
32Hex
33Hex
34Hex
35Hex
–55–
Data
Mode Register 0
Mode Register 1
Mode Register 2
Mode Register 3
Mode Register 4
Mode Register 5
Mode Register 6
Mode Register 7
Mode Register 8
Mode Register 9
Timing Register 0
Timing Register 1
Subcarrier Frequency Register 0
Subcarrier Frequency Register 1
Subcarrier Frequency Register 2
Subcarrier Frequency Register 3
Subcarrier Phase Register
Closed Captioning Ext Register 0
Closed Captioning Ext Register 1
Closed Captioning Register 0
Closed Captioning Register 1
Pedestal Control Register 0
Pedestal Control Register 1
Pedestal Control Register 2
Pedestal Control Register 3
CGMS_WSS Reg 0
CGMS_WSS Reg 1
CGMS_WSS Reg 2
Teletext Control Register
Contrast Control Register
Color Control Register 1
Color Control Register 2
Hue Control Register
Brightness Control Register
Sharpness Response Register
DNR 0
DNR 1
DNR 2
Gamma 0
Gamma 1
Gamma 2
Gamma 3
Gamma 4
Gamma 5
Gamma 6
Gamma 7
Gamma 8
Gamma 9
Gamma 10
Gamma 11
Gamma 12
Gamma 13
Brightness Detect Register
Output Clock Register
01Hex
07Hex
08Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
08Hex
00Hex
CBHex
8AHex
09Hex
2AHex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
00Hex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
xxHex
72Hex
ADV7190/ADV7191
APPENDIX 9
NTSC WAVEFORMS (WITH PEDESTAL)
130.8 IRE
PEAK COMPOSITE
1268.1mV
100 IRE
REF WHITE
1048.4mV
714.2mV
387.6mV
334.2mV
7.5 IRE
0 IRE
BLACK LEVEL
BLANK LEVEL
–40 IRE
SYNC LEVEL
48.3mV
REF WHITE
1048.4mV
Figure 101. NTSC Composite Video Levels
100 IRE
714.2mV
7.5 IRE
0 IRE
BLACK LEVEL
BLANK LEVEL
–40 IRE
SYNC LEVEL
387.6mV
334.2mV
48.3mV
Figure 102. NTSC Luma Video Levels
PEAK CHROMA
1067.7mV
835mV (pk-pk)
286mV (pk-pk)
BLANK/BLACK LEVEL
650mV
PEAK CHROMA
232.2mV
0mV
Figure 103. NTSC Chroma Video Levels
100 IRE
REF WHITE
1052.2mV
720.8mV
7.5 IRE
0 IRE
BLACK LEVEL
BLANK LEVEL
387.5mV
331.4mV
–40 IRE
SYNC LEVEL
45.9mV
Figure 104. NTSC RGB Video Levels
–56–
REV. 0
ADV7190/ADV7191
NTSC WAVEFORMS (WITHOUT PEDESTAL)
130.8 IRE
PEAK COMPOSITE
1289.8mV
100 IRE
REF WHITE
1052.2mV
714.2mV
0 IRE
BLANK/BLACK LEVEL
338mV
–40 IRE
SYNC LEVEL
52.1mV
Figure 105. NTSC Composite Video Levels
100 IRE
REF WHITE
1052.2mV
714.2mV
0 IRE
BLANK/BLACK LEVEL
SYNC LEVEL
–40 IRE
338mV
52.1mV
Figure 106. NTSC Luma Video Levels
PEAK CHROMA
1101.6mV
903.2mV (pk-pk)
307mV (pk-pk)
BLANK/BLACK LEVEL
650mV
PEAK CHROMA
198.4mV
0mV
Figure 107. NTSC Chroma Video Levels
100 IRE
REF WHITE
1052.2mV
715.7mV
BLANK/BLACK LEVEL
0 IRE
SYNC LEVEL
–40 IRE
Figure 108. NTSC RGB Video Levels
REV. 0
–57–
336.5mV
51mV
ADV7190/ADV7191
PAL WAVEFORMS
PEAK COMPOSITE
1284.2mV
1047.1mV
REF WHITE
696.4mV
350.7mV
BLANK/BLACK LEVEL
50.8mV
SYNC LEVEL
Figure 109. PAL Composite Video Levels
REF WHITE
1047mV
696.4mV
BLANK/BLACK LEVEL
350.7mV
SYNC LEVEL
50.8mV
Figure 110. PAL Luma Video Levels
PEAK CHROMA
1092.5mV
885mV (pk-pk)
300mV (pk-pk)
BLANK/BLACK LEVEL
650mV
PEAK CHROMA
207.5mV
0mV
Figure 111. PAL Chroma Video Levels
REF WHITE
1050.2mV
698.4mV
BLANK/BLACK LEVEL
351.8mV
SYNC LEVEL
51mV
Figure 112. PAL RGB Video Levels
–58–
REV. 0
ADV7190/ADV7191
505mV
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
WHITE
YELLOW
UV WAVEFORMS
505mV
423mV
334mV
171mV
BETACAM LEVEL
BETACAM LEVEL
82mV
0mV
0mV
0mV
0mV
–82mV
171mV
334mV
–423mV
505mV
–505mV
467mV
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
Figure 116. NTSC 100% Color Bars, No Pedestal V Levels
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
WHITE
YELLOW
Figure 113. NTSC 100% Color Bars, No Pedestal U Levels
467mV
391mV
309mV
158mV
BETACAM LEVEL
BETACAM LEVEL
76mV
0mV
0mV
0mV
0mV
–76mV
–158mV
–309mV
–391mV
–467mV
–467mV
350mV
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
WHITE
YELLOW
Figure 117. NTSC 100% Color Bars with Pedestal V Levels
BLACK
BLUE
RED
MAGENTA
GREEN
CYAN
YELLOW
WHITE
Figure 114. NTSC 100% Color Bars with Pedestal U Levels
350mV
293mV
232mV
SMPTE LEVEL
SMPTE LEVEL
118mV
57mV
0mV
0mV
0mV
0mV
–57mV
–118mV
–232mV
–293mV
–350mV
–350mV
Figure 115. PAL 100% Color Bars U Levels
REV. 0
Figure 118. PAL 100% Color Bars V Levels
–59–
ADV7190/ADV7191
OUTPUT WAVEFORMS
0.6
VOLTS
0.4
0.2
0.0
0.2
L608
0.0
10.0
20.0
30.0
40.0
50.0
60.0
MICROSECONDS
NOISE REDUCTION: 0.00 dB
APL = 39.1%
625 LINE PAL
NO FILTERING
PRECISION MODE OFF
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
SOUND-IN-SYNC OFF
SYNC = SOURCE
FRAMES SELECTED: 1 2 3 4
Figure 119. 100%/75% PAL Color Bars
VOLTS
0.5
0.0
L575
0.0
10.0
APL NEEDS SYNC = SOURCE!
625 LINE PAL
NO FILTERING
20.0
30.0
40.0
50.0
MICROSECONDS
PRECISION MODE OFF
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
60.0
70.0
SOUND-IN-SYNC OFF
SYNC = A
FRAMES SELECTED: 1
Figure 120. 121%/75% PAL Color Bars Luminance
–60–
REV. 0
ADV7190/ADV7191
VOLTS
0.5
0.0
–0.5
L575
10.0
20.0
30.0
40.0
MICROSECONDS
APL NEEDS SYNC = SOURCE!
625 LINE PAL
NO FILTERING
50.0
60.0
NO BRUCH SIGNAL
PRECISION MODE OFF
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
SOUND-IN-SYNC OFF
SYNC = A
FRAMES SELECTED: 1
Figure 121. 100%/75% PAL Color Bars Chrominance
100.0
VOLTS
IRE:FLT
0.5
50.0
0.0
0.0
–50.0
0.0
F1
L76
10.0
20.0
30.0
40.0
MICROSECONDS
APL = 44.6%
525 LINE NTSC
60.0
PRECISION MODE OFF
NO FILTERING
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
SYNC = A
FRAMES SELECTED: 1 2
Figure 122. 100%/75% NTSC Color Bars
REV. 0
50.0
–61–
ADV7190/ADV7191
100.0
0.6
0.4
VOLTS
IRE:FLT
50.0
0.2
0.0
0.0
–0.2
F2
L238
10.0
20.0
30.0
40.0
MICROSECONDS
NOISE REDUCTION: 15.05dB
APL = 44.7%
525 LINE NTSC
NO FILTERING
50.0
PRECISION MODE OFF
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
60.0
SYNC = SOURCE
FRAMES SELECTED: 1 2
Figure 123. 100%/75% NTSC Color Bars Luminance
0.4
50.0
0.0
IRE:FLT
VOLTS
0.2
–0.2
–50.0
–0.4
F1
L76
0.0
10.0
20.0
30.0
40.0
MICROSECONDS
NOISE REDUCTION: 15.05dB
APL NEEDS SYNC = SOURCE!
525 LINE NTSC
50.0
60.0
PRECISION MODE OFF
NO FILTERING
SYNCHRONOUS
SLOW CLAMP TO 0.00 V AT 6.72 s
SYNC = B
FRAMES SELECTED: 1 2
Figure 124. 100%/75% NTSC Color Bars Chrominance
–62–
REV. 0
ADV7190/ADV7191
PARADE SMPTE/EBU PAL
mV
Y(A)
mV
Pb(B)
mV
Pr(C)
700
250
250
600
200
200
500
150
150
400
100
100
300
50
50
200
0
0
–50
–50
0
–100
–100
100
–150
–150
200
–200
–200
–250
–250
100
300
Figure 125. PAL YUV Parade Plot
mV
GREEN (A)
mV
BLUE (B)
700
700
600
600
500
500
400
400
300
300
200
200
100
100
0
mV
RED (C)
700
600
500
400
300
200
100
0
0
100
100
100
200
200
200
300
300
300
Figure 126. PAL RGB Waveforms
REV. 0
–63–
ADV7190/ADV7191
VIDEO MEASUREMENT PLOTS
COLOR BAR (NTSC)
FIELD = 1
LINE = 21
WFM
FCC COLOR BAR
LUMINANCE LEVEL (IRE)
99.6
69.0
55.9
48.1
36.3
28.3
15.7
7.7
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
BLACK
100
50
0
CHROMINANCE LEVEL (IRE)
0.0
62.1
87.6
81.8
81.8
87.8
62.1
0.0
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
BLACK
167.3
283.8
240.9
60.80
103.6
347.1
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
100
50
0
CHROMINANCE PHASE (DEGREE)
400
200
0
GRAY
AVERAGE 32
BLACK
32
Figure 127. NTSC Color Bar Measurement
COLOR BAR (PAL)
LINE = 570
WFM
COLOR BAR
LUMINANCE LEVEL (mV)
1000
695.7
464.8
366.6
305.7
217.3
156.4
61.2
–0.4
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
BLACK
500
0
CHROMINANCE LEVEL (mV)
1000
0.0
474.4
669.1
623.5
624.7
669.6
475.2
0.0
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
BLACK
166.7
283.3
240.4
60.4
103.2
346.7
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
500
0
CHROMINANCE PHASE (DEGREE)
400
300
200
100
0
GRAY
AVERAGE 32
BLACK
32
Figure 128. PAL Color Bar Measurement
–64–
REV. 0
ADV7190/ADV7191
DG DP (NTSC)
MOD 5 STEP
WFM
DG DP (PAL)
FIELD = 1, LINE = 21
0.00
0.21
0.02
0.07
0.27
MIN = 0.00, MAX = 0.32, pk-pk = 0.32
DIIFFERENTIAL GAIN (PERCENT)
MIN = 0.00, MAX = 0.27, p-p/MAX = 0.27
DIIFFERENTIAL GAIN (PERCENT)
2.5
MOD 5 STEP
WFM
LINE = 570
0.08
2.5
0.00
0.30
0.15
0.24
0.32
0.26
1st
2nd
3rd
4th
5th
6th
1.5
1.5
0.5
0.5
–0.5
–0.5
–1.5
–1.5
–2.5
1st
2nd
3rd
4th
2.5
0.10
6th
–2.5
0.12
0.15
0.13
0.10
2.5
1.5
1.5
0.5
0.5
–0.5
–0.5
–1.5
–1.5
–2.5
1st
2nd
AVERAGE 32
3rd
4th
5th
6th
–2.5
Figure 129. NTSC DG DP Measurement
1st
2nd
0.13
0.16
3rd
4th
0.12
0.14
5th
6th
32
LUMINANCE NONLINEARITY (PAL)
MOD 5 STEP
WFM
WFM
MOD 5 STEP
LINE = 570
pk-pk = 0.4
LUMINANCE NONLINEARITY (PERCENT)
99.90
0.09
Figure 131. PAL DG DP Measurement
FIELD = 2, LINE = 77
111
0.00
AVERAGE 32
32
LUMINANCE NONLINEARITY (NTSC)
MIN = 0.00, MAX = 0.16, pk-pk = 0.16
DIFFERENTIAL PHASE (DEGREE)
MIN = 0.00, MAX = 0.20, pk-pk = 0.20
DIFFERENTIAL PHASE (DEGREE)
0.00
5th
99.90
99.60
100.0
99.90
109
111
107
109
105
107
103
105
101
103
99
pk-pk = 0.8
LUMINANCE NONLINEARITY (PERCENT)
113
99.6
99.9
100.0
2nd
3rd
99.6
99.9
101
97
99
95
97
93
95
91
93
89
1st
AVERAGE 32
2nd
3rd
4th
91
5th
1st
32
AVERAGE 32
Figure 130. NTSC Luminance Nonlinearity
REV. 0
4th
32
Figure 132. PAL Luminance Nonlinearity
–65–
5th
ADV7190/ADV7191
CHROMINANCE NONLINEARITY(NTSC)
WFM
FIELD = 2, LINE = 217
CHROMINANCE AMPLITUDE ERROR (PERCENT)
0.5
NTSC–7 COMBINATION
CHROMINANCE NONLINEARITY(PAL)
WFM
LINE = 572
CHROMINANCE AMPLITUDE ERROR (PERCENT)
REF = 40IRE PACKET
0.0
–0.3
0.6
0.0
140mV
420mV
MOD 3 STEP
REF = 420mV PACKET
–0.4
10
10
0
0
–10
–10
20IRE
40IRE
80IRE
CHROMINANCE PHASE ERROR (DEGREE)
–0.0
5
REF = 40IRE PACKET
0.0
0.0
0
0
–5
–5
20IRE
40IRE
80IRE
CHROMINANCE LUMINANCE INTERMODULATION (PERCENT OF 714mV)
0.0
0.1
700mV
CHROMINANCE PHASE ERROR (DEGREE)
REF = 420mV PACKET
–0.3
0.0
–0.3
140mV
420mV
700mV
CHROMINANCE LUMINANCE INTERMODULATION (PERCENT OF 700mV)
0.1
0.0
0.0
0.1
420mV
700mV
0.2
0.1
0.2
0.0
0.0
–0.1
–0.2
–0.2
20IRE
AVERAGE 32
40IRE
80IRE
140mV
AVERAGE 32
32
Figure 133. NTSC Chrominance Nonlinearity
CHROMINANCE AM/PM (NTSC)
FIELD = 2, LINE = 217
WFM
Figure 135. PAL Chrominance Nonlinearity
RED FIELD
CHROMINANCE AM/PM (PAL)
LINE = 572
BANDWIDTH 10kHz TO 100kHz
–86.5dB RMS
–90
–85
–80
–75
PM NOISE
–70
AM NOISE
–65
–60
dB RMS
–90
–85
APPROPRIATE
–80
–75
–70
–84.2dB RMS
–95
–82.7dB RMS
–95
WFM
BANDWIDTH 10kHz TO 100kHz
AM NOISE
–95
32
–90
–85
–80
–75
PM NOISE
–65
–60
dB RMS
–65
–60
dB RMS
–65
–60
dB RMS
–80.5dB RMS
–95
(0dB = 714mV p-p WITH AGC FOR 100% CHROMINANCE LEVEL)
–70
–90
–85
–80
–75
–70
(0dB = 700mV p-p WITH AGC FOR 100% CHROMINANCE LEVEL)
Figure 134. NTSC Chrominance AM/PM
Figure 136. PAL Chrominance AM/PM
–66–
REV. 0
ADV7190/ADV7191
NOISE SPECTRUM (NTSC)
PEDESTAL
WFM
NOISE SPECTRUM (PAL)
FIELD = 2, LINE = 223
PEDESTAL
WFM
LINE = 511
NOISE LEVEL = –79.7dB RMS
AMPLITUDE (0dB = 714mV p-p)
NOISE LEVEL = –79.1dB RMS
AMPLITUDE (0dB = 714mV p-p)
BANDWIDTH 10kHz TO FULL
BANDWIDTH 10kHz TO FULL
20
0
0
–20
–20
–40
–40
–60
–60
–80
–80
–100
–100
1
2
3
MHz
4
5
6
1
4
5
6
7
Figure 139. PAL Noise Spectrum: Pedestal
RAMP
WFM
NOISE SPECTRUM (PAL)
FIELD = 2, LINE = 217
RAMP
WFM
LINE = 572
NOISE LEVEL = –63.1dB RMS
AMPLITUDE (0dB = 714mV p-p)
NOISE LEVEL = –62.3dB RMS
AMPLITUDE (0dB = 700mV p-p)
BANDWIDTH 100kHz TO FULL (TILT NULL)
BANDWIDTH 100kHz TO FULL (TILT NULL)
0
0
–10
–10
–20
–20
–30
–30
–40
–40
–50
–50
–60
–60
–70
–70
–80
–80
–90
–90
–100
–100
1
2
3
MHz
4
5
6
1
2
3
4
5
6
MHz
Figure 138. NTSC Noise Spectrum: Ramp
REV. 0
3
MHz
Figure 137. NTSC Noise Spectrum: Pedestal
NOISE SPECTRUM (NTSC)
2
Figure 140. PAL Noise Spectrum: Ramp
–67–
7
ADV7190/ADV7191
APPENDIX 10
VECTOR PLOTS
V
APL = 39.6%
SYSTEM LINE L608
ANGLE (DEG) 0.0
GAIN 1.000 0.000dB
625 LINE PAL
BURST FROM SOURCE
DISPLAY +V AND –V
cy
R
g
M
g
75%
100%
YI
b
U
yl
B
G
Cy
m
g
r
SOUND IN SYNC OFF
Figure 141. PAL Vector Plot
R-Y
APL = 45.1%
SYSTEM LINE L76F1
ANGLE (DEG) 0.0
GAIN 1.000 0.000dB
525 LINE NTSC
BURST FROM SOURCE
cy
I
R
M
g
YI
Q
b
100%
B-Y
75%
B
G
Cy
–Q
–I
SETUP 7.5%
Figure 142. NTSC Vector Plot
–68–
REV. 0
ADV7190/ADV7191
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.640 (16.25)
0.630 (16.00) SQ
0.620 (15.75)
0.063 (1.60)
MAX
0.030 (0.75)
0.024 (0.60)
0.018 (0.45)
SEATING
PLANE
64
49
1
48
12
TYP
0.555 (14.10)
0.551 (14.00) SQ
0.547 (13.90)
TOP VIEW
(PINS DOWN)
0.004 (0.102)
MAX LEAD
COPLANARITY
10
6
2
16
33
32
17
0.031 (0.80)
BSC
0.007 (0.17)
MAX
C3753–4–5/00 (rev. 0) 00230
64-Lead LQFP
(ST-64)
0.057 (1.45)
0.055 (1.40)
0.053 (1.35)
PRINTED IN U.S.A.
7
0
0.014 (0.35)
REV. 0
–69–