Electronic control gear QUICKTRONIC® DIMMABLE for FH-lamps, single-lamp version QT-FH 1x14/230-240 DIM h Page 1 a l h b N L + - 1 2 3 4 L b Reference : QT-FH 1x14/230-240 DIM for lamp : 1x FH 14 W Mains voltage [V] : 230/240 Permissible voltage fluctuations [V] : 198 - 264 Permissible battery voltage [V] : 176 - 254 Lamp start : Warm start within 2 s Mains frequency [Hz] : 0/50 - 60 Operating frequency [kHz] : approx. 40 at 100% luminous flux, approx. 100 at 3% luminous flux Mains current [A] : 0,09 Power factor [c] : 0,95 System wattage [W] : 18 Luminous flux [lm] : 1350 Temperature range [°C] : +5 - +50 Radio interference suppression : to DIN VDE 0875/CISPR 15/EN 55015 Harmonics : to DIN VDE 0712 Part 23/IEC 929/IEC 555-2/EN 60929 Immunity : to EN 61547 Length l [mm] : 359 Width b [mm] : 30 Height h [mm] : 30 Distance between holes a [mm] : 350 Standard pack [pcs] : 12 Weight [g] : 310 QUICKTRONIC® DIMMABLE for FH®/FQ® lamps This electronic high-frequency control gear enables FH® and FQ® lamps to be dimmed from 100% to 3% (1%) luminous flux via a 1 - 10V DC control line. The 1-10 V control line allows a wide variety of possible connections, ranging from simple manual control units for small systems through daylight-controlled regulation systems to modern energy management systems with PC and digital I-Bus technology. QUICKTRONIC® DIMMABLE goes beyond all current conventional and electronic solutions not just in terms of lighting comfort and energy consumption, but also in simplicity of operation and installation. Comfort: - Dimmable from 100% to 3% luminous flux for FH® lamps - Dimmable from 100% to 1% luminous flux for FQ® lamps - Flicker-free starting at all dimmer settings - Numerous control options with a low-voltage control signal (1 - 10 V) - Electronic control gear from different circuits can be dimmed together on different phases Electronic control gear QUICKTRONIC® DIMMABLE for FH-lamps, single-lamp version QT-FH 1x14/230-240 DIM Page 2 - Easy to incorporate into existing lighting control systems Economy: - Potentially large energy savings thanks to daylight-dependent lighting control - Long lamp life - Protective warm start Safety: - Safety shutdown of the power supply to defective lamps - Compliance with European standards for safety, operation and EMC - Overvoltage protective cutout for short-duration voltage surges (DIN VDE 0160) and for temporary overvoltages - Greater fire protection because lamps operate at lower temperatures and luminaires can be constructed to meet EN 60598/DIN VDE 0710 and DIN VDE 0711 standards - Can be used in emergency lighting systems as per DIN VDE 0108. Applications: Adjustable lighting in conference rooms, film projection rooms, exhibition rooms, CAD and PC rooms, control rooms, film recording studios, and for energy savings in offices with daylight-dependent lighting control. General: - Supply voltage: 230V/240V - Mains frequency: 0/50 to 60 Hz - Lamp start: warm start within 2 s. Lamp will start at any dimmer setting. - Radio interference suppression: to DIN VDE 0875/CISPR 15/EN 55015 - Mains harmonics: to DIN VDE 0712 Part 23/IEC 929/EN 61000-3-2/EN 60929 - Immunity to EN 61547 - Same luminous flux for AC and DC operation. - Values for luminous flux, mains current and system wattage at a dimmer setting of 100% - Max. 0.6 mA control current at the 1-10V interface