MAXIM MAX1507

19-2899; Rev 1; 11/03
KIT
ATION
EVALU
E
L
B
A
AVAIL
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
The MAX1507 achieves high flexibility by providing an
adjustable fast-charge current and thermal regulation
setpoints. Other features include the charging status
(CHG) of the battery and an active-low control input (EN).
The MAX1507 accepts a +4.25V to +13V supply, but disables charging when the input voltage exceeds +7V to
protect against unqualified or faulty AC adapters. The
MAX1507 operates over the extended temperature
range (-40°C to +85°C) and is available in a compact
8-pin thermally enhanced 3mm x 3mm Thin DFN package with 0.8mm height.
Features
♦ Stand-Alone Linear 1-Cell Li+ Battery Charger
♦ No External FET, Reverse-Blocking Diode, or
Current-Sense Resistor Required
♦ Programmable Fast-Charge Current (0.8A max)
♦ Proprietary Programmable Die-Temperature
Regulation Control (+90°C, +100°C, and +130°C)
♦ +4.25V to +13V Input Voltage Range with Input
Overvoltage Protection (OVP) Above +7V
♦ Charge-Current Monitor for Fuel Gauging
♦ Low Dropout Voltage—130mV at 0.425A
♦ Input Power-Source Detection Output (VL) and
Charge-Enable Input (EN)
♦ Soft-Start Limits Inrush Current
♦ Charge Status Output (CHG) for LED or
Microprocessor Interface
♦ Small 3mm x 3mm 8-Pin Thin DFN Package,
0.8mm High
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
TOP
MARK
Cellular and Cordless Phones
MAX1507ETA
-40°C to +85°C
8 Thin DFN-EP*
AGW
PDAs
*EP = Exposed paddle.
Applications
Digital Cameras and MP3 Players
USB Appliances
Typical Operating Circuit
Charging Cradles and Docks
Bluetooth™ Equipment
BATT
TEMP
EN
TOP VIEW
CHG
Pin Configuration
8
7
6
5
INPUT
4.25V TO 13V
IN
BATT
1µF
1µF
Li+
4.2V
MAX1507
CHG
MAX1507
ISET
OFF
1
2
3
4
VL
IN
GND
ISET
ON
EN
TEMP
VL
GND
2.80kΩ
0.47µF
3mm x 3mm THIN DFN
Bluetooth is a trademark of Ericsson.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX1507
General Description
The MAX1507 is an intelligent, stand-alone constant-current, constant-voltage (CCCV), thermally regulated linear
charger for a single-cell lithium-ion (Li+) battery. The
MAX1507 integrates the current-sense circuit, MOS pass
element, and thermal-regulation circuitry, and also eliminates the reverse-blocking Schottky diode to create the
simplest and smallest charging solution for hand-held
equipment.
The MAX1507 functions as a stand-alone charger to
control the charging sequence from the prequalification
state through fast-charge, top-off charge, and fullcharge indication.
Proprietary thermal-regulation circuitry limits the die
temperature when fast charging or while exposed to
high ambient temperatures, allowing maximum charging current without damaging the IC.
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
ABSOLUTE MAXIMUM RATINGS
IN, CHG to GND .....................................................-0.3V to +14V
VL, BATT, ISET, EN, TEMP to GND ..........................-0.3V to +6V
VL to IN...................................................................-14V to +0.3V
IN to BATT Continuous Current.............................................0.9A
Continuous Power Dissipation (TA = +70°C)
8-Pin TDFN (derate 24.4mW/°C above+70°C) ..........1951mW
Short-Circuit Duration.................................................Continuous
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 5V, VBATT = 4.0V, TEMP = EN = CHG = unconnected, RISET = 2.8kΩ to GND, CVL = 0.47µF, BATT bypassed to GND with 1µF,
TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
CONDITIONS
Input Voltage Range
Input Operating Range
ACOK Trip Point, IN
Overvoltage Lockout Trip Point
MIN
V
6.50
V
VIN - VBATT, VIN rising
20
40
60
VIN - VBATT, VIN falling
15
30
45
VIN rising
6.5
7
7.5
VIN hysteresis
0.11
Disabled, EN = VL
1
2
0.8
1.5
OFF state (VIN = VBATT = 4.0V)
3.3
VL Load Regulation
IVL = 100µA to 2mA
-71
VL Temperature Coefficient
IVL = 100µA
-2
VIN rising
2.95
Hysteresis
0.17
EN = VL
4
10
Maximum RMS Charge Current
0.8
VBATT rising
2
µA
A
TA = 0°C to +85°C
4.162
4.2
4.238
TA = -40°C to +85°C
4.150
4.2
4.250
4.4
4.67
4.9
_______________________________________________________________________________________
mV
V
10
BATT Removal Detection Threshold
mA
mV/°C
3
IBATT = 0
V
V
-200
VIN = 0 to 4V
Battery Regulation Voltage
mV
0.065
IVL = 100µA
BATT Input Current
UNITS
4.25
VL Output Voltage
VL Undervoltage Lockout Trip Point
MAX
13
Charging (IIN - IBATT)
IN Input Current
TYP
0
V
V
Linear Li+Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
(VIN = 5V, VBATT = 4.0V, TEMP = EN = CHG = unconnected, RISET = 2.8kΩ to GND, CVL = 0.47µF, BATT bypassed to GND with 1µF,
TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
CONDITIONS
MIN
BATT Removal Detection-Threshold Hysteresis
TYP
MAX
200
Minimum BATT Bypass Capacitance
mV
1
Fast-Charge Current-Loop System Accuracy
VBATT = 3.5V
Precharge Current System Accuracy
Percentage of the fast-charge current,
VBATT = 2.2V
520
562
mA
5
10
15
%
TEMP = VL
130
TEMP = floating
100
VBATT Precharge Threshold Voltage
VBATT rising
Current-Sense Amplifier Gain, ISET to IBATT
in Fast Charge Mode
IBATT = 500mA, VISET = 1.4V
TEMP = GND
VBATT = 4.1V, IBATT = 425mA
EN Logic Input Low Voltage
4.25V < VIN < 6.5V
EN Logic Input High Voltage
4.25V < VIN < 6.5V
V CHG = 13V
Full Battery Detection Current Threshold
(as a Percentage of the Fast-Charge Current)
IBATT falling
2.3
2.5
2.7
V
0.880
0.958
1.035
mA/A
130
200
mV
0.52
V
1.3
EN Internal Pulldown Resistor
CHG Output High Leakage Current
°C
90
Regulator Dropout Voltage (VIN - VBATT )
V CHG = 1V
µF/A
478
Die-Temperature-Regulation Set Point
CHG Output Low Current
UNITS
V
100
200
400
kΩ
5
12
20
mA
TA = +25°C
1
TA = +85°C
0.002
5
10
15
µA
%
Note 1: Limits are 100% production tested at TA = +25°C. Limits over operating temperature range are guaranteed through correlation
using statistical quality control (SQC) methods.
_______________________________________________________________________________________
3
MAX1507
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VIN = 5V, VBATT = 4.0V, TEMP = EN = CHG = unconnected, RISET = 2.8kΩ to GND, CIN = 1µF, CBATT = 1µF, CVL = 0.47µF, TA =
+25°C, unless otherwise noted.)
1.0
0.5
1.0
0.5
2
4
6
8
12
10
300
200
0
0
2
4
6
8
10
0
12
1
2
3
4
BATTERY VOLTAGE (V)
CHARGE CURRENT
vs. INPUT VOLTAGE
CHARGE CURRENT
vs. INPUT-VOLTAGE HEADROOM
BATTERY REGULATION VOLTAGE
vs. TEMPERATURE
VBATT = 4.0V
INPUT VOLTAGE (V)
VIN - VBATT (V)
520
500
480
460
-15
10
35
60
MAX1507 toc08
VBATT = 3.6V
400
300
0
85
VBATT = 4.0V
500
100
60
-40
600
400
35
4.186
700
200
10
4.189
800
420
AMBIENT TEMPERATURE (°C)
4.192
900
440
-15
4.195
1000
CHARGE CURRENT (mA)
540
-40
4.198
CHARGE CURRENT
vs. AMBIENT TEMPERATURE (TEMP = VL)
MAX1507 toc07
560
4.201
TEMPERATURE (°C)
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
TEMP = VL
4.204
4.180
0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32 0.36 0.40
580
4.207
4.183
0 1 2 3 4 5 6 7 8 9 10 11 12 13
600
4.210
MAX1507 toc06
600
550
500
450
400
350
300
250
200
150
100
50
0
BATTERY REGULATION VOLTAGE (V)
CHARGE CURRENT (mA)
TEMP = VL
MAX1507 toc05
INPUT VOLTAGE (V)
MAX1507 toc04
INPUT VOLTAGE (V)
600
550
500
450
400
350
300
250
200
150
100
50
0
CHARGE CURRENT (mA)
400
100
0
0
TEMP = VL
500
1.5
0
4
600
MAX1507 toc02
EN = VL
CHARGE CURRENT (mA)
1.5
2.0
DISABLED-MODE SUPPLY CURRENT (mA)
IBATT = 0
MAX1507 toc01
2.0
SUPPLY CURRENT (mA)
CHARGE CURRENT
vs. BATTERY VOLTAGE
DISABLED-MODE SUPPLY
CURRENT vs. INPUT VOLTAGE
MAX1507 toc03
SUPPLY CURRENT
vs. INPUT VOLTAGE
CHARGE CURRENT (mA)
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
RISET = 1.87kΩ
-40
-15
10
35
60
AMBIENT TEMPERATURE (°C)
_______________________________________________________________________________________
85
85
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
CHARGE CURRENT
vs. AMBIENT TEMPERATURE (TEMP = GND)
CHARGE CURRENT
vs. AMBIENT TEMPERATURE (TEMP = OPEN)
700
600
500
VBATT = 3.6V
400
300
VBATT = 4.0V
900
800
CHARGE CURRENT (mA)
CHARGE CURRENT (mA)
800
1000
MAX1507 toc10
VBATT = 4.0V
900
MAX1507 toc09
1000
700
600
500
VBATT = 3.6V
400
300
200
200
100
RISET = 1.87kΩ
100
RISET = 1.87kΩ
0
0
-40
-15
10
35
60
-40
85
-15
10
35
60
85
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
Pin Description
PIN
NAME
FUNCTION
1
VL
Internally Generated Logic Supply for Chip. Bypass VL to GND with a 0.47µF capacitor.
2
IN
Input Supply Voltage. Bypass IN to GND with a 1µF capacitor to improve line noise and transient rejection.
3
GND
Ground. Connect GND and exposed pad to a large copper trace for maximum power dissipation.
4
ISET
Charge-Current Program and Fast-Charge Current Monitor. Output current from ISET is 0.958mA per amp of
battery charging current. The charging current is set by connecting a resistor from ISET to GND. Fast-charge
current = 1461V / RISETΩ.
5
EN
Logic-Level Enable Input. Drive EN high to disable charger. Pull EN low or float for normal operation. EN has
an internal 200kΩ pulldown resistor.
6
TEMP
Three-Level Input Pin. Connect TEMP to VL, GND, or leave floating. Sets maximum die temperature for
thermal regulation loop. Connection to GND = +90°C, floating = +100°C, VL = +130°C. TEMP is Hi-Z during
shutdown.
7
BATT
Li+ Battery Connection. Bypass BATT to GND with a capacitor of at least 1µF per ampere of charge current.
8
CHG
Charging Indicator, Open-Drain Output. CHG goes low (and can turn on an LED) when charging begins.
CHG is high impedance when the battery current drops below 10% of the fast-charging current, or when EN
is high. Connect a pullup resistor to the µP’s I/O voltage when interfacing with a µP logic input.
—
PAD
Exposed Pad. Connect exposed pad to a large copper trace for maximum power dissipation. The pad is
internally connected to GND.
_______________________________________________________________________________________
5
MAX1507
Typical Operating Characteristics (continued)
(VIN = 5V, VBATT = 4.0V, TEMP = EN = CHG = unconnected, RISET = 2.8kΩ to GND, CIN = 1µF, CBATT = 1µF, CVL = 0.47µF, TA =
+25°C, unless otherwise noted.)
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
Detailed Description
state. Once the cell has passed 2.5V, the charger softstarts before it enters the fast-charge stage. The fastcharge current level is programmed through a resistor
from ISET to ground. As the battery voltage approaches 4.2V, the charging current is reduced. If the battery
current drops to less than 10% of the fast-charging current, the CHG indicator goes high impedance, signaling the battery is fully charged. At this point the
MAX1507 enters a constant voltage-regulation mode to
The MAX1507 charger uses voltage, current, and thermal-control loops to charge a single Li+ cell and to protect the battery (Figure 1). When a Li+ battery with a
cell voltage below 2.5V is inserted, the MAX1507
charger enters the prequalification stage where it
precharges that cell with 10% of the user-programmed
fast-charge current. The CHG indicator output is driven
low (Figure 2) to indicate entry into the prequalification
MAX1507
BATT
IN
VREF
OUTPUT DRIVER,
CURRENT SENSE,
AND LOGIC
ISET
TEMPERATURE
SENSOR
+90°C
+100°C
+130°C
IREF
IN
VL
TEMP
IN
VL
0.47µF
BATT
VLUVLO
REF
IN
VINOVLO
VLOK
EN
ON
INOK
LOGIC
REFOK
CHG
200kΩ
REFOK
N
GND
Figure 1. Functional Diagram
6
_______________________________________________________________________________________
Linear Li+Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
MAX1507
ASYNCHRONOUS FROM
ANYWHERE
VIN > 7V +
VBATT > VIN +
EN = HIGH
SHUTDOWN
VBATT < 2.5V
D
AN D
7V T AN
<
T
V IN > V BA
V IN = LOW
EN
PRECHARGE
10% CHARGE CURRENT
LED = ON
CHARGER = OFF
LED = OFF
VIN > 7V +
VBATT > VIN +
EN = HIGH
VBATT < 2.4V
VBATT > 2.5V
FAST CHARGE
100% CHARGER CURRENT
LED = ON
ICHARGE < 10%
OF ISET
ICHARGE > 20%
OF ISET
FULL BATT
LED = OFF
FULL BATT CONTINUES
TO REGULATE BATT
UP TO 4.2V
Figure 2. Charge State Diagram
maintain the battery at full charge. If, at any point while
charging the battery, the die temperature approaches
the user-selected temperature setting (TEMP pin), the
MAX1507 reduces the charging current so the die temperature does not exceed the temperature-regulation
set point.
The thermal-regulation loop limits the MAX1507 die
temperature to the value selected by the TEMP input by
reducing the charge current as necessary (see the
Thermal-Regulation Selection section). This feature not
only protects the MAX1507 from overheating, but also
allows higher charge current without risking damage to
the system.
EN Charger Enable Input
EN is a logic input (active low) to enable the charger.
Drive EN low, leave floating, or connect to GND to
enable the charger control circuitry. Drive EN high to
disable the charger control circuitry. EN has a 200kΩ
internal pulldown resistance.
VL Internal Voltage Regulator
The MAX1507 linear charger contains an internal linear
regulator available on the VL output pin. VL requires a
0.47µF ceramic bypass capacitor to GND. VL is regulated to 3.3V whenever the input voltage is above 3.5V.
_______________________________________________________________________________________
7
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
CHG Charge Indicator Output
to the value set by TEMP. The MAX1507 operates normally while the thermal loop is active. An active thermal
loop does not indicate a fault condition. TEMP allows
the MAX1507 to maximize the charge current while providing protection against excessive power dissipation.
Connect TEMP to GND to regulate the die temperature
at +90°C. Leave TEMP floating to regulate the die temperature at +100°C. Connect TEMP to VL to regulate
the die temperature at +130°C.
CHG is an open-drain current source for indicating
charge status. Table 1 describes the state of CHG during different stages of operation.
CHG is a nominal 12mA current source suitable for driving a charge-indication LED. If the MAX1507 is used
in conjunction with a microprocessor, a pullup resistor
to the logic I/O voltage allows CHG to indicate charge
status to the µP instead of driving an LED.
Capacitor Selection
Soft-Start
Connect a ceramic capacitor from BATT to GND for
proper stability. Use a 1µF X5R ceramic capacitor for
most applications.
Connect a 1µF ceramic capacitor from IN to GND. Use
a larger input bypass capacitor for high input voltages
or high charging currents to reduce supply noise.
Connect a 0.47µF ceramic capacitor from VL to GND.
An analog soft-start algorithm activates when entering
fast-charge mode. When the prequalification state is
complete (VBATT exceeds +2.5V), the charging current
ramps up in 3ms to the full charging current. This
reduces the inrush current on the input supply.
Applications Information
Charge-Current Selection
Thermal Considerations
The maximum charging current is programmed by an
external RISET resistor connected from ISET to GND.
Select the RISET value based on the following formula:
The MAX1507 is in a thermally enhanced thin DFN
package with exposed paddle. Connect the exposed
paddle of the MAX1507 to a large copper ground plane
to provide a thermal contact between the device and
the circuit board. The exposed paddle transfers heat
away from the device, allowing the MAX1507 to charge
the battery with maximum current, while minimizing the
increase in die temperature.
IFAST= 1461V / RISETΩ
where IFAST is in amps and RISET is in ohms. ISET can
also be used to monitor the fast-charge current level.
The output current from the ISET pin is 0.958mA per
amp of charging current. The output voltage at ISET is
proportional to the charging current as follows:
DC Input Sources
VISET = (ICHG x RISET) / 1044
The voltage at ISET is nominally 1.4V at the selected
fast-charge current, and falls with charging current as
the cell becomes fully charged.
The MAX1507 operates from well-regulated DC
sources. The full-charging input-voltage range is 4.25V
to 7V. The device can stand up to 13V on the input
without damage to the IC. If VIN is greater than 7V, then
the MAX1507 stops charging.
An appropriate power supply must provide at least
4.25V when sourcing the desired peak charging current. It also must stay below 6.5V when unloaded.
Thermal-Regulation Selection
Set the regulated die temperature of the MAX1507 with
the TEMP three-level logic input. The MAX1507
reduces the charge current to limit the die temperature
Table 1. CHG States
EN
VIN
VBATT
IBATT
CHG
X
VBATT
VIN
0
Hi-Z
Low
4.25V ≤ VIN ≤ 7V
< 2.5V
10% of IFAST
Low
Prequalification
Low
4.25V ≤ VIN ≤ 7V
≥ 2.5V
IFAST*
Low
Fast Charge
Low
4.25V ≤ VIN ≤ 7V
4.2V
10% of IFAST
Hi-Z
Full Charge
Low
>7V
X
0
Hi-Z
Overvoltage
High
X
X
0
Hi-Z
Disabled
STATE
Shutdown
X = Don’t care.
*IFAST is reduced as necessary to maintain the die temperature set by the TEMP input.
8
_______________________________________________________________________________________
Linear Li+Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
Microprocessor-Interfaced Charger
Figure 3 shows the MAX1507 as a µP-cooperated Li+
battery charger. The MAX1507 starts charging the battery when EN is low. The µP can drive EN high to disable the charger. Use a logic-biased NPN transistor as
an inverter circuit to generate an AC_ON signal for the
system to detect the presence of an input supply. CHG
can be used to detect the charge status of a battery.
By monitoring V ISET , the system can measure the
charge current.
4.2V Li+
AC/DC
ADAPTER
IN
BATT
1µF
1µF
VI/O
MAX1507
CHG
GND
AC_ON
ROHM
DTC114EM
TEMP
SYSTEM
VL
0.47µF
ISET
EN
2.8kΩ
CHARGE-CURRENT MONITOR
VI/O
LOW: CHARGE, HIGH: FULL OR OFF
Figure 3. µP Interfaced Li+ Battery Charger
_______________________________________________________________________________________
9
MAX1507
USB-Powered Li+ Charger
The universal serial bus (USB) provides a high-speed
serial communication port as well as power for the
remote device. The MAX1507 can be configured to
charge its battery at the highest current possible from
the host port. Figure 4 shows the MAX1507 as a USB
battery charger. To make the circuit compatible with
either 100mA or 500mA USB ports, the circuit initializes
at 95mA charging current. The microprocessor then
interrogates the host to determine its current capability.
If the host port is capable, the charging current is
increased to 435mA. The 435mA current was chosen to
avoid exceeding the 500mA USB specification.
Application Circuits
Stand-Alone Li+ Charger
The MAX1507 provides a complete Li+ charging solution. The Typical Application Circuit on the front page
shows the MAX1507 as a stand-alone Li+ battery
charger. The 2.8kΩ resistor connected to ISET sets a
charging current of 520mA. The LED indicates when
either fast-charge or precharge qualification has
begun. When the battery is full, the LED turns off.
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
4.2V Li+
VBUS
GND
IN
BATT
1µF
1µF
VI/O
MAX1507
GND
CHG
ROHM
DTC114EM
TEMP
SYSTEM
VL
0.47µF
USB PORT
EN
ISET
15.4kΩ
HIGH: 435mA, LOW: 95mA
4.3kΩ
N
VI/O
D+
D-
Figure 4. USB Battery Charger
Layout and Bypassing
Connect a 1µF ceramic input capacitor as close to the
device as possible. Provide a large copper GND plane
to allow the exposed paddle to sink heat away from the
device. Connect the battery to BATT as close to the
device as possible to provide accurate battery voltage
sensing. Make all high-current traces short and wide to
minimize voltage drops. For an example layout, refer to
the MAX1507/MAX1508 evaluation kit layout.
10
Chip Information
TRANSISTOR COUNT: 1812
PROCESS: BiCMOS
______________________________________________________________________________________
Linear Li+Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
6, 8, &10L, DFN THIN.EPS
L
A
D
D2
A2
PIN 1 ID
1
N
1
C0.35
b
E
PIN 1
INDEX
AREA
[(N/2)-1] x e
REF.
E2
DETAIL A
e
k
A1
CL
CL
L
L
e
e
A
DALLAS
SEMICONDUCTOR
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, 6, 8 & 10L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY
APPROVAL
DOCUMENT CONTROL NO.
21-0137
REV.
D
1
2
______________________________________________________________________________________
11
MAX1507
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
MAX1507
Linear Li+ Battery Charger with Integrated Pass FET
and Thermal Regulation in 3mm x 3mm Thin DFN
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
COMMON DIMENSIONS
SYMBOL
A
MIN.
MAX.
0.70
0.80
D
2.90
3.10
E
2.90
3.10
A1
0.00
0.05
L
k
0.20
0.40
0.25 MIN.
A2
0.20 REF.
PACKAGE VARIATIONS
PKG. CODE
N
D2
E2
e
JEDEC SPEC
b
T633-1
6
1.50–0.10
2.30–0.10
0.95 BSC
MO229 / WEEA
0.40–0.05
1.90 REF
T833-1
8
1.50–0.10
2.30–0.10
0.65 BSC
MO229 / WEEC
0.30–0.05
1.95 REF
T1033-1
10
1.50–0.10
2.30–0.10
0.50 BSC
MO229 / WEED-3
0.25–0.05
2.00 REF
[(N/2)-1] x e
DALLAS
SEMICONDUCTOR
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, 6, 8 & 10L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
APPROVAL
DOCUMENT CONTROL NO.
21-0137
REV.
D
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.