AD ADCMP608BKSZ-R2

Rail-to-Rail, Fast, Low Power 2.5 V to 5.5 V,
Single-Supply TTL/CMOS Comparator
ADCMP608
Fully specified rail to rail at VCC = 2.5 V to 5.5 V
Input common-mode voltage from −0.2 V to VCC + 0.2 V
Low glitch CMOS-/TTL-compatible output stage
40 ns propagation delay
Low power: 1 mW at 2.5 V
Shutdown pin
Power supply rejection > 60 dB
−40°C to +125°C operation
APPLICATIONS
FUNCTIONAL BLOCK DIAGRAM
NONINVERTING
INPUT
+
ADCMP608
INVERTING
INPUT
Q OUTPUT
–
SDN
06769-001
FEATURES
Figure 1.
High speed instrumentation
Clock and data signal restoration
Logic level shifting or translation
High speed line receivers
Threshold detection
Peak and zero-crossing detectors
High speed trigger circuitry
Pulse-width modulators
Current-/voltage-controlled oscillators
GENERAL DESCRIPTION
The ADCMP608 is a fast comparator fabricated on XFCB2, an
Analog Devices, Inc. proprietary process. This comparator is
exceptionally versatile and easy to use. Features include an input
range from VEE − 0.2 V to VCC + 0.2 V, low noise, TTL-/CMOScompatible output drivers, and shutdown inputs. The device
offers 40 ns propagation delays driving a 15 pF load with 10 mV
overdrive on 500 μA typical supply current.
A flexible power supply scheme allows the device to operate
with a single +2.5 V positive supply and a −0.2 V to + 2.7 V
input signal range up to a +5.5 V positive supply with a −0.2 V
to +5.7 V input signal range.
The TTL-/CMOS-compatible output stage is designed to drive
up to 15 pF with full rated timing specifications and to degrade
in a graceful and linear fashion as additional capacitance is
added. The input stage of the comparator offers robust protection against large input overdrive, and the outputs do not phase
reverse when the valid input signal range is exceeded.
The ADCMP608 is available in a tiny 6-lead SC70 package with
a single-ended output and a shutdown pin.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
ADCMP608
TABLE OF CONTENTS
Features .............................................................................................. 1
Application Information...................................................................7
Applications....................................................................................... 1
Power/Ground Layout and Bypassing........................................7
Functional Block Diagram .............................................................. 1
TTL-/CMOS-Compatible Output Stage ....................................7
General Description ......................................................................... 1
Optimizing Performance..............................................................7
Revision History ............................................................................... 2
Comparator Propagation Delay Dispersion ..............................7
Specifications..................................................................................... 3
Crossover Bias Point .....................................................................8
Electrical Characteristics............................................................. 3
Minimum Input Slew Rate Requirement ...................................8
Absolute Maximum Ratings............................................................ 4
Typical Application Circuits ............................................................9
Thermal Resistance ...................................................................... 4
Outline Dimensions ....................................................................... 10
ESD Caution.................................................................................. 4
Ordering Guide .......................................................................... 10
Pin Configuration and Function Descriptions............................. 5
Typical Performance Characteristics ............................................. 6
REVISION HISTORY
4/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADCMP608
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VCC = 2.5 V, TA = −40°C to +125°C. Typical values are TA = 25°C, unless otherwise noted.
Table 1.
Parameter
DC INPUT CHARACTERISTICS
Voltage Range
Common-Mode Range
Differential Voltage
Offset Voltage
Bias Current
Offset Current
Capacitance
Resistance, Differential Mode
Resistance, Common Mode
Active Gain
Common-Mode Rejection
SHUTDOWN PIN CHARACTERISTICS 1
VIH
VIL
IIH
Sleep Time
Wake-Up Time
DC OUTPUT CHARACTERISTICS
Output Voltage High Level
Output Voltage Low Level
AC PERFORMANCE 2
Rise Time/Fall Time
Symbol
Conditions
Min
VP, VN
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
−0.2
−0.2
VOS
IP, IN
−5.0
−0.4
−1.0
CP, CN
AV
CMRR
tSD
tH
VOH
VOL
tR, tF
Propagation Delay
tPD
Propagation Delay Skew—Rising to
Falling Transition
Overdrive Dispersion
Common-Mode Dispersion
POWER SUPPLY
Supply Voltage Range
Positive Supply Current
VCC
IVCC
Power Dissipation
PD
Power Supply Rejection Ratio
Shutdown Current
PSRR
ISD
Typ
±3
Max
Unit
VCC
VCC
VCC
+5.0
+0.4
+1.0
V
V
V
mV
μA
μA
pF
kΩ
kΩ
dB
dB
dB
1
−0.5 V to VCC + 0.5 V
−0.5 V to VCC + 0.5 V
200
100
VCC = 2.5 V, VCM = −0.2 V to 2.7 V
VCC = 5.5 V
45
45
Comparator is operating
Shutdown guaranteed
VIH = VCC
lCC < 100 μA
VPP = 10 mV, output valid
VCC = 2.5 V to 5.5 V
IOH = 0.8 mA, VCC = 2.5 V
IOL = 0.8 mA, VCC = 2.5 V
VCC = 2.5 V to 5.5 V
10% to 90%, VCC = 2.5 V
10% to 90%, VCC = 5.5 V
VOD = 10 mV, VCC = 2.5 V
VOD = 50 mV, VCC = 5.5 V
VCC = 2.5 V
VCC = 5.5 V
10 mV < VOD < 125 mV
−0.2 V < VCM < VCC + 0.2 V
2.0
−0.2
−6
7000
4000
80
+0.4
300
150
VCC − 0.4
0.4
25 to 50
45 to 75
30 to 50
35 to 60
4.5
8
12
1.5
2.5
VCC = 2.5 V
VCC = 5.5 V
VCC = 2.5 V
VCC = 5.5 V
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
1
VCC
+0.4
+6
V
V
μA
ns
ns
V
V
ns
ns
ns
ns
ns
ns
ns
ns
550
800
1.375
4.95
5.5
800
1300
2.0
7.15
250
350
−50
V
μA
μA
mW
mW
dB
μA
The output will be in a high impedance mode when the device is in shutdown mode. Note that this feature should be used with care since the enable/disable time is
much longer than with a true tristate output.
2
VIN = 100 mV square input at 1 MHz, VCM = 0 V, CL = 15 pF, VCCI = 2.5 V, unless otherwise noted.
Rev. 0 | Page 3 of 12
ADCMP608
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 2.
Parameter
Supply Voltages
Supply Voltage
(VCC to GND)
Supply Differential
Input Voltages
Input Voltage
Differential Input Voltage
Maximum Input/Output Current
Shutdown Control Pin
Applied Voltage (SDN to GND)
Maximum Input/Output Current
Output Current
Temperature
Operating Temperature, Ambient
Operating Temperature, Junction
Rating
−0.5 V to +6.0 V
−6.0 V to +6.0 V
−0.5 V to VCC+ 0.5 V
±(VCC + 0.5 V)
±50 mA
THERMAL RESISTANCE
−0.5 V to VCC + 0.5 V
±50 mA
±50 mA
Table 3. Thermal Resistance
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Package Type
ADCMP608 6-Lead SC70
1
−40°C to +125°C
150°C
Measurement in still air.
ESD CAUTION
Rev. 0 | Page 4 of 12
θJA1
426
Unit
°C/W
ADCMP608
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Q 1
6
VCC
5
SDN
4
VN
VEE 2
VP 3
TOP VIEW
(Not to Scale)
06769-002
ADCMP608
Figure 2. Pin Configuration
Table 4. ADCMP608 Pin Function Descriptions
Pin No.
1
Mnemonic
Q
2
3
4
5
6
VEE
VP
VN
SDN
VCC
Description
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater than the
analog voltage at the inverting input, VN.
Negative Supply Voltage.
Noninverting Analog Input.
Inverting Analog Input.
Shutdown. Drive this pin low to shut down the device.
VCC Supply.
Rev. 0 | Page 5 of 12
ADCMP608
TYPICAL PERFORMANCE CHARACTERISTICS
VCC =2.5 V, TA = 25°C, unless otherwise noted.
38.0
4
37.8
3
37.6
PROPAGATION DELAY (ns)
5
2
0
–1
–2
+125°C
–3
06769-003
–40°C
–5
–1.0
–0.5
0
37.2
37.0
PROPAGATION DELAY RISE
36.8
36.6
36.4
+25°C
–4
37.4
0.5
1.0
1.5
2.0
2.5
3.0
06769-006
IB (µA)
1
PROPAGATION DELAY FALL
36.2
36.0
0.5
3.5
VCM AT VCC (2.5V)
1.0
1.5
2.0
2.5
3.0
VCM AT VCC (2.5V)
Figure 3. Input Bias Current vs. Input Common-Mode Voltage
Figure 6. Propagation Delay vs. Input Common-Mode Voltage
60
55
50
Q
VCC = 5.5V
RISE DELAY
40
VCC = 5.5V
FALL DELAY
35
30
VCC = 2.5V
FALL DELAY
25
0
06769-004
20
VCC = 2.5V
RISE DELAY
50
100
0.5V/DIV
10ns/DIV
150
06769-007
TPD (ns)
45
OD (mV)
Figure 4. Propagation Delay vs. Input Overdrive at VCC = 2.5 V and 5.5 V
Figure 7. 1 MHz Output Voltage Waveform VCC = 2.5 V
1.5
SOURCE
1.0
Q
0.5
0
–1.0
–1.0 –0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
1V/DIV
10ns/DIV
4.0
VOUT (V)
Figure 8. 1 MHz Output Voltage Waveform VCC = 5.5 V
Figure 5. Load Current (mA) vs. VOH/VOL
Rev. 0 | Page 6 of 12
06769-008
–0.5
06769-005
LOAD CURRENT (mA)
SINK
ADCMP608
APPLICATION INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
VLOGIC
It is also important to adequately bypass the input and output
supplies. A 0.1 μF bypass capacitor should be placed as close as
possible to the VCC supply pin. The capacitor should be connected
to the GND plane with redundant vias placed to provide a
physically short return path for output currents flowing back
from ground to the VCC pin. High frequency bypass capacitors
should be carefully selected for minimum inductance and ESR.
Parasitic layout inductance should also be strictly controlled to
maximize the effectiveness of the bypass at high frequencies.
TTL-/CMOS-COMPATIBLE OUTPUT STAGE
Specified propagation delay performance can be achieved only
by keeping the capacitive load at or below the specified minimums.
The output of the ADCMP608 is designed to directly drive one
Schottky TTL, or three low power Schottky TTL loads, or the
equivalent. For large fan outs, buses, or transmission lines, use
an appropriate buffer to maintain the excellent speed and
stability of the comparator.
With the rated 15 pF load capacitance applied, more than half
of the total device propagation delay is output stage slew time.
Because of this, the total propagation delay decreases as VCC
decreases, and instability in the power supply may appear as
excess delay dispersion.
Delay is measured to the 50% point for whatever supply is in
use; thus, the fastest times are observed with the VCC supply at
2.5 V, and larger values are observed when driving loads that
switch at other levels.
Overdrive and input slew rate dispersions are not significantly
affected by output loading and VCC variations.
The TTL-/CMOS-compatible output stage is shown in the
simplified schematic diagram (see Figure 9). Because of its
inherent symmetry and generally good behavior, this output
stage is readily adaptable for driving various filters and other
unusual loads.
A1
Q1
+IN
–IN
OUTPUT
AV
A2
GAIN STAGE
Q2
OUTPUT STAGE
06769-009
The ADCMP608 comparator is a high speed device. Despite the
low noise output stage, it is essential to use proper high speed
design techniques to achieve the specified performance. Because
comparators are uncompensated amplifiers, feedback in any phase
relationship is likely to cause oscillations or undesired hysteresis. Of
critical importance is the use of low impedance supply planes,
particularly the output supply plane (VCC) and the ground plane
(GND). Individual supply planes are recommended as part of a
multilayer board. Providing the lowest inductance return path for
switching currents ensures the best possible performance in the
target application.
Figure 9. Simplified Schematic Diagram of
TTL-/CMOS-Compatible Output Stage
OPTIMIZING PERFORMANCE
As with any high speed comparator, proper design and layout
techniques are essential for obtaining the specified performance.
Stray capacitance, inductance, common power and ground
impedances, or other layout issues can severely limit performance
and can often cause oscillation. The source impedance should be
minimized as much as is practicable. High source impedance, in
combination with the parasitic input capacitance of the comparator,
causes an undesirable degradation in bandwidth at the input, thus
degrading the overall response. Higher impedances encourage
undesired coupling.
COMPARATOR PROPAGATION
DELAY DISPERSION
The ADCMP608 comparator is designed to reduce propagation
delay dispersion over a wide input overdrive range of 10 mV to
VCC – 1 V. Propagation delay dispersion is the variation in
propagation delay that results from a change in the degree of
overdrive or slew rate (how far or how fast the input signal
exceeds the switching threshold).
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications, such as data
communication, automatic test and measurement, and instrumentation. It is also important in event-driven applications, such
as pulse spectroscopy, nuclear instrumentation, and medical
imaging. Dispersion is defined as the variation in propagation
delay as the input overdrive conditions are changed (Figure 10
and Figure 11).
ADCMP608 dispersion is typically < 12 ns as the overdrive
varies from 10 mV to 125 mV. This specification applies to
both positive and negative signals because the device has very
closely matched delays for both positive-going and negativegoing inputs, and very low output skews. Remember to add the
actual device offset to the overdrive for repeatable dispersion
measurements.
Rev. 0 | Page 7 of 12
ADCMP608
500mV OVERDRIVE
CROSSOVER BIAS POINT
Rail-to-rail inputs of this type, in both op amps and comparators,
have a dual front-end design. Certain devices are active near the
VCC rail and others are active near the VEE rail. At some predetermined point in the common-mode range, a crossover occurs. At
this point, normally VCC/2, the direction of the bias current reverses
and there are changes in measured offset voltages and currents.
INPUT VOLTAGE
10mV OVERDRIVE
DISPERSION
Q OUTPUT
06769-010
VN ± VOS
Figure 10. Propagation Delay—Overdrive Dispersion
The ADCMP608 slightly elaborates on this scheme. Crossover
points can be found at approximately 0.8 V and 1.6 V.
MINIMUM INPUT SLEW RATE REQUIREMENT
INPUT VOLTAGE
1V/ns
VN ± VOS
DISPERSION
Q OUTPUT
06769-011
10V/ns
Figure 11. Propagation Delay—Slew Rate Dispersion
With the rated load capacitance and normal good PC board
design practice, as discussed in the Optimizing Performance
section, these comparators should be stable at any input slew
rate with no hysteresis. Broadband noise from the input stage is
observed in place of the violent chattering seen with most other
high speed comparators. With additional capacitive loading or
poor bypassing, oscillation may be encountered. These oscillations are due to the high gain bandwidth of the comparator in
combination with feedback through parasitics in the package
and PC board. In many applications, chattering is not harmful.
Rev. 0 | Page 8 of 12
ADCMP608
TYPICAL APPLICATION CIRCUITS
2.5V TO 5V
0.1µF
2kΩ
2kΩ
ADCMP608
OUTPUT
06769-012
INPUT
0.1µF
Figure 12. Self-Biased, 50% Slicer
CMOS
VCC
2.5V TO 5V
100Ω
ADCMP608
OUTPUT
06769-013
LVDS
Figure 13. LVDS-to-CMOS Receiver
Rev. 0 | Page 9 of 12
ADCMP608
OUTLINE DIMENSIONS
2.20
2.00
1.80
1.35
1.25
1.15
6
5
4
1
2
3
2.40
2.10
1.80
PIN 1
0.65 BSC
1.30 BSC
1.00
0.90
0.70
0.10 MAX
1.10
0.80
0.30
0.15
0.40
0.10
SEATING
PLANE
0.22
0.08
0.46
0.36
0.26
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-203-AB
Figure 14. 6-Lead Thin Shrink Small Outline Transistor Package (SC70)
(KS-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADCMP608BKSZ-R2 1
ADCMP608BKSZ-RL1
ADCMP608BKSZ-REEL71
1
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
6-Lead Thin Shrink Small Outline Transistor Package (SC70)
6-Lead Thin Shrink Small Outline Transistor Package (SC70)
6-Lead Thin Shrink Small Outline Transistor Package (SC70)
Z = RoHS Compliant Part.
Rev. 0 | Page 10 of 12
Package
Option
KS-6
KS-6
KS-6
Branding
G0U
G0U
G0U
ADCMP608
NOTES
Rev. 0 | Page 11 of 12
ADCMP608
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06769-0-4/07(0)
Rev. 0 | Page 12 of 12