AD OP191

a
Micropower Single-Supply
Rail-to-Rail Input/Output Op Amps
OP191/OP291/OP491
FEATURES
Single-Supply Operation: 2.7 V to 12 V
Wide Input Voltage Range
Rail-to-Rail Output Swing
Low Supply Current: 300 µA/Amp
Wide Bandwidth: 3 MHz
Slew Rate: 0.5 V/µs
Low Offset Voltage: 700 µV
No Phase Reversal
APPLICATIONS
Industrial Process Control
Battery Powered Instrumentation
Power Supply Control and Protection
Telecom
Remote Sensors
Low Voltage Strain Gage Amplifiers
DAC Output Amplifier
OP191/OP291/OP491 PIN CONFIGURATIONS
8-Lead Narrow-Body SO
(S Suffix)
1
8
2
7
3
OP191
4
NC
1
8
NC
6
–INA
2
7
V+
5
+INA
3
6
OUTA
–V
4
5
NC
8-Lead Narrow-Body SO
(S Suffix)
1
3
4
8
OP291
Applications for these amplifiers include portable telecom
equipment, power supply control and protection, and interface
for transducers with wide output ranges. Sensors requiring a
rail-to-rail input amplifier include Hall effect, piezo electric,
and resistive transducers.
6
5
8
+V
2
7
OUTB
3
6
–INB
4
5
+INB
OUTA
1
–INA
+INA
–V
OP291
14-Lead Epoxy DIP
(P Suffix)
OUTA 1
14-Lead SO
(S Suffix)
OUTA 1
14 OUTD
–INA
13 –IND
+INA 3
+INA 3
12 +IND
+V
+V
4
OP491
11 –V
10 +INC
6
9
–INC
OUTB 7
8
OUTC
–INB
13 –IND
4
12 +IND
OP491
11 –V
+INB 5
10 +INC
6
9 –INC
–INB
+INB 5
14 OUTD
2
2
–INA
The ability to swing rail-to-rail at both the input and output
enables designers to build multistage filters in single-supply
systems and maintain high signal-to-noise ratios.
The OP191/OP291/OP491 are specified over the extended
industrial (–40°C to +125°C) temperature range. The OP191
single and OP291 dual amplifiers are available in 8-pin plastic
DIPs and SO surface mount packages. The OP491 quad is
available in 14-pin DIPs and narrow 14-pin SO packages.
Consult factory for OP491 TSSOP availability.
8-Lead Epoxy DIP
(P Suffix)
7
GENERAL DESCRIPTION
Fabricated on Analog Devices’ CBCMOS process, the OP191
family has a unique input stage that allows the input voltage to
safely extend 10 volts beyond either supply without any phase
inversion or latch-up. The output voltage swings to within
millivolts of the supplies and continues to sink or source
current all the way to the supplies.
OP191
NC = NO CONNECT
2
The OP191, OP291 and OP491 are single, dual and quad
micropower, single-supply, 3 MHz bandwidth amplifiers featuring rail-to-rail inputs and outputs. All are guaranteed to
operate from a 3 volt single supply as well as ± 5 volt dual
supplies.
8-Lead Epoxy DIP
(P Suffix)
OUTB 7
8 OUTC
14-Lead
TSSOP
(RU Suffix)
1
2
14
13
12
3
4
5
6
7
OP491
11
10
9
8
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
OP191/OP291/OP491–SPECIFICATIONS
ELECTRICAL SPECIFICATIONS (@ V = +3.0 V, V
S
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
OP191G
VOS
OP291/OP491G
VOS
Input Bias Current
IB
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection Ratio
CMRR
Large Signal Voltage Gain
AVO
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
VOH
VOL
Short Circuit Limit
ISC
Open Loop Impedance
ZOUT
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
PSRR
ISY
CM
= 0.1 V, VO = 1.4 V, TA = +25°C unless otherwise noted)
Conditions
Min
–40 ≤ TA ≤ +125°C
DYNAMIC PERFORMANCE
Slew Rate
Slew Rate
Full-Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
+SR
–SR
BWP
tS
GBP
θO
CS
RL = 10 kΩ
RL = 10 kΩ
1% Distortion
To 0.01%
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
f = 1 kHz, RL = 10 kΩ
80
500
1
700
1.25
50
70
8
16
3
µV
mV
µV
mV
nA
nA
nA
nA
V
dB
dB
V/mV
V/mV
µV/°C
pA/°C
pA/°C
0.1
–40 ≤ TA ≤ +125°C
VS = 2.7 V to 12 V
–40°C ≤ TA ≤ +125°C
VO = 0 V
–40°C ≤ TA ≤ +125°C
Units
30
–40 ≤ TA ≤ +125°C
RL = 100 kΩ to GND
–40°C to +125°C
RL = 2 kΩ to GND
–40°C to +125°C
RL = 100 kΩ to V+
–40°C to +125°C
RL = 2 kΩ to V+
–40°C to +125°C
Sink/Source
–40°C to +125°C
f = 1 MHz, AV = 1
Max
80
–40 ≤ TA ≤ +125°C
VCM = 0 V to 2.9 V
–40 ≤ TA ≤ +125°C
RL = 10 kΩ , VO = 0.3 V to 2.7 V
–40 ≤ TA ≤ +125°C
Typ
0
70
65
25
2.95
2.90
2.8
2.70
90
87
70
50
1.1
100
20
2.99
2.98
2.9
2.8
4.5
40
± 8.75
± 6.0
± 13.5
± 10.5
200
80
75
110
110
200
330
10
35
75
130
350
480
V
V
V
V
mV
mV
mV
mV
mA
mA
Ω
dB
dB
µA
µA
0.4
0.4
1.2
22
3
45
145
V/µs
V/µs
kHz
µs
MHz
Degrees
dB
2
35
0.8
µV p-p
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
–2–
REV. 0
OP191/OP291/OP491
ELECTRICAL SPECIFICATIONS (@ V = +5.0 V, V
S
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
OP191
VOS
OP291/OP491
VOS
Input Bias Current
IB
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection Ratio
CMRR
Large Signal Voltage Gain
AVO
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
VOH
VOL
Short Circuit Limit
ISC
Open Loop Impedance
ZOUT
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
PSRR
ISY
CM
= 0.1 V, VO = 1.4 V, TA = +25°C unless otherwise noted)
Conditions
–40 ≤ TA ≤ +125°C
VS = 2.7 V to 12 V
–40 ≤ TA ≤ +125°C
VO = 0 V
–40 ≤ TA ≤ +125°C
+SR
–SR
BWP
tS
GBP
θO
CS
RL = 10 kΩ
RL = 10 kΩ
1% Distortion
To 0.01%
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
f = 1 kHz, RL = 10 kΩ
NOTES
+5 V specifications are guaranteed by +3 V and ± 5 V testing.
Specifications subject to change without notice.
–3–
Units
80
500
1.0
700
1.25
50
60
8
16
5
µV
mV
µV
mV
nA
nA
nA
nA
V
dB
dB
V/mV
V/mV
µV/°C
pA/°C
pA/°C
0.1
–40 ≤ TA ≤ +125°C
RL = 100 kΩ to GND
–40°C to +125°C
RL = 2 kΩ to GND
–40°C to +125°C
RL = 100 kΩ to V+
–40°C to +125°C
RL = 2 kΩ to V+
–40°C to +125°C
Sink/Source
–40°C to +125°C
f = 1 MHz, AV = 1
Max
30
–40 ≤ TA ≤ +125°C
VCM = 0 V to 4.9 V
–40 ≤ TA ≤ +125°C
RL = 10 kΩ , VO = 0.3 V to 4.7 V
–40 ≤ TA ≤ +125°C
–40 ≤ TA ≤ +125°C
Typ
80
–40 ≤ TA ≤ +125°C
DYNAMIC PERFORMANCE
Slew Rate
Slew Rate
Full-Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
REV. 0
Min
0
70
65
25
4.95
4.90
4.8
4.65
93
90
70
50
1.1
100
20
4.99
4.98
4.85
4.75
4.5
40
± 8.75
± 6.0
± 13.5
± 10.5
200
80
75
110
110
220
350
10
35
75
155
400
500
V
V
V
V
mV
mV
mV
mV
mA
mA
Ω
dB
dB
µA
µA
0.4
0.4
1.2
22
3
45
145
V/µs
V/µs
kHz
µs
MHz
Degrees
dB
2
35
0.8
µV p-p
nV/√Hz
pA/√Hz
OP191/OP291/OP491
ELECTRICAL SPECIFICATIONS (@ V = ±5.0 V, –4.9 V ≤ V
O
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
OP191
VOS
OP291/OP491
VOS
IOS
Input Voltage Range
Common-Mode Rejection
CMR
Large Signal Voltage Gain
AVO
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
Short Circuit Limit
ISC
Open Loop Impedance
ZOUT
PSRR
ISY
Units
80
500
1
700
1.25
50
70
8
16
+5
µV
mV
µV
mV
nA
nA
nA
nA
V
dB
dB
0.1
–40 ≤ TA ≤ +125°C
VO
Max
30
–40 ≤ TA ≤ +125°C
VCM = ± 5 V
–40 ≤ TA ≤ +125°C
RL = 10 kΩ, VO = ± 4.7 V,
–40 ≤ TA ≤ +125°C
Typ
80
–40 ≤ TA ≤ +125°C
Input Offset Current
Supply Current/Amplifier
Min
–40 ≤ TA ≤ +125°C
IB
POWER SUPPLY
Power Supply Rejection Ratio
≤ +4.9 V, TA = +25°C unless otherwise noted)
Conditions
Input Bias Current
OUTPUT CHARACTERISTICS
Output Voltage Swing
CM
–5
75
67
25
100
97
70
50
1.1
100
20
V/mV
µV/°C
pA/°C
pA/°C
RL = 100 kΩ to GND
–40°C to +125°C
RL = 2 kΩ to GND
–40 ≤ TA ≤ +125°C
Sink/Source
–40°C to +125°C
f = 1 MHz, AV = 1
± 4.93
± 4.90
± 4.80
± 4.65
± 8.75
±6
± 4.99
± 4.98
± 4.95
± 4.75
± 16
± 13
200
V
V
V
V
mA
mA
Ω
VS = ± 5 V
–40 ≤ TA ≤ +125°C
VO = 0 V
–40 ≤ TA ≤ +125°C
80
70
110
100
260
390
dB
dB
µA
µA
DYNAMIC PERFORMANCE
Slew Rate
Full-Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
± SR
BWP
tS
GBP
θO
CS
RL =10 kΩ
1% Distortion
To 0.01%
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
f = 1 kHz
420
550
0.5
1.2
22
3
45
145
V/µs
kHz
µs
MHz
Degrees
dB
2
35
0.8
µV p-p
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
VS = ±5V
RL = 2kΩ
AV = +1
VIN = 20Vp-p
5V
100
90
INPUT
OUTPUT
10
0%
200µs
5V
Figure 1. Input and Output with Inputs Overdriven by 5 V
–4–
REV. 0
OP191/OP291/OP491
WAFER TEST LIMITS (@ V = +3.0 V, V
S
CM
= 0.1 V, TA = +25°C unless otherwise noted)
Parameter
Symbol
Offset Voltage
Input Bias Current
Input Offset Current
Input Voltage Range
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large Signal Voltage Gain
Output Voltage High
Output Voltage Low
Supply Current/Amplifier
VOS
IB
IOS
VCM
CMRR
PSRR
AVO
VOH
VOL
ISY
Conditions
Limit
Units
VCM = 0 V to +2.9 V
V = 2.7 V to +12 V
R L = 10 kΩ
R L = 2 kΩ to GND
R L = 2 kΩ to V+
VO = 0 V, R L = ∞
± 300
50
8
V– to V+
70
80
50
2.8
75
350
µV max
nA max
nA
V min
dB min
dB min
V/mV min
V min
mV max
µA max
NOTE
Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard
product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing.
ABSOLUTE MAXIMUM RATINGS 1
ORDERING GUIDE
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +16 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . .GND to VS + 10 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Output Short-Circuit Duration to GND . . . . . . . . . . Indefinite
Storage Temperature Range
P, S, RU Packages . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
OP191/OP291/OP491G . . . . . . . . . . . . . . . –40°C to +125°C
Junction Temperature Range
P, S, RU Packages . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
Package Type
θJA2
θJC
Units
8-Pin Plastic DIP (P)
8-Pin SOIC (S)
14-Pin Plastic DIP (P)
14-Pin SOIC (S)
14-Pin TSSOP (RU)
103
158
76
120
180
43
43
33
36
35
°C/W
°C/W
°C/W
°C/W
°C/W
Model
Temperature
Range
Package
Description
Package
Option
OP191GP
OP191GS
OP191GBC
OP291GP
OP291GS
OP291GBC
OP491GP
OP491GS
OP491HRU
OP491GBC
–40°C to +125°C
–40°C to +125°C
+25°C
–40°C to +125°C
–40°C to +125°C
+25°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
+25°C
8-Pin Plastic DIP
8-Pin SOIC
DICE
8-Pin Plastic DIP
8-Pin SOIC
DICE
14-Pin Plastic DIP
14-Pin SOIC
14-Pin TSSOP
DICE
N-8
SO-8
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.
2
θJA is specified for the worst case conditions; i.e., θJA is specified for device in socket
for P-DIP packages; θJA is specified for device soldered in circuit board for TSSOP
and SOIC packages.
2
1
14
N-8
SO-8
N-14
SO-14
RU-14
13
DICE CHARACTERISTICS
1
8
3
12
4
11
5
10
7
7
2
2
6
3
5
6
3
4
4
6
OP191 Die Size 0.047 × 0.066 Inch,
3,102 Sq. Mils. Substrate (Die Backside) Is Connected to V+.
Transistor Count, 74.
REV. 0
OP291 Die Size 0.070 × 0.070 Inch,
4,900 Sq. Mils. Substrate (Die Backside) Is Connected to V+.
Transistor Count, 146
–5–
7
8
9
OP491 Die Size 0.070 × 0.110 Inch,
7,700 Sq. Mils. Substrate (Die Backside) Is Connected to V+.
Transistor Count, 290.
OP191/OP291/OP491–Typical Performance Characteristics
180
VS = +3V
INPUT OFFSET VOLTAGE – mV
VS = +3V
–40°C < TA < +125°C
BASED ON 600 OP AMPS
100
120
80
UNITS
UNITS
0
120
VS = +3V
160 T = +25°C
A
BASED ON 1200
140 OP AMPS
100
80
60
60
40
40
20
–0.02
VCM = 0.1V
–0.04
VCM = 0V
–0.06
VCM = 3V
–0.08
–0.1
VCM = 2.9V
–0.12
20
0
0.22
Figure 2. OP291 Input Offset Voltage
Distribution, VS = +3 V
0
VS = +3V
VCM = 0.1V
–20
–30
–40
VCM = 0V
25
85
TEMPERATURE – °C
–0.4
VCM = 0.1V
VCM = 2.9V
–0.6
VCM = 3V
–0.8
VCM = 0V
–1.0
–1.2
–1.4
+VO @ RL = 2k
2.85
2.80
VS = +3V
25
85
TEMPERATURE – °C
125
Figure 8. Output Voltage Swing
vs. Temperature, VS = +3 V
–12
–18
–24
1200
120
100
80
0
60
45
40
90
20
135
0
180
–20
225
–40
100
0
–6
Figure 7. Input Bias Current vs.
Common-Mode Voltage, VS = +3 V
1k
10k
100k
1M
FREQUENCY – Hz
270
10M
Figure 9. Open-Loop Gain & Phase
vs. Frequency, VS = +3 V
–6–
OPEN-LOOP GAIN –V/mV
OPEN-LOOP GAIN – dB
2.90
6
0 0.30 0.60 0.90 1.2 1.5 1.8 2.1 2.4 2.7 3.0
INPUT COMMON MODE VOLTAGE – Volts
VS = +3V
TA = +25°C
140
2.95
12
125
160
+VO @ RL = 100k
18
–36
25
85
TEMPERATURE – °C
Figure 6. Input Offset Current
vs. Temperature, VS = +3 V
3.00
24
–30
–1.8
–40
Figure 5. Input Bias Current vs.
Temperature, VS = +3 V
VS = +3V
30
VS = +3V
–1.6
125
125
36
INPUT BIAS CURRENT – nA
INPUT OFFSET CURRENT – nA
INPUT BIAS CURRENT – nA
VCM = 2.9V
10
85
25
TEMPERATURE – °C
Figure 4. Input Offset Voltage vs.
Temperature, VS = +3 V
–0.2
–50
OUTPUT SWING – Volts
–40
7
VCM = 3V
20
2.75
–40
2
3
4
5
6
INPUT OFFSET VOLTAGE – µV/ °C
Figure 3. OP291 Input Offset Voltage Drift Distribution, VS = +3 V
30
–60
–40
1
0
40
–10
–0.14
0
0.14
–0.10
–0.02
0.06
INPUT OFFSET VOLTAGE – mV
PHASE SHIFT – Degrees
0
–0.18
1000
RL = 100kΩ,
VCM = 2.9V
800
RL = 100kΩ,
VCM = 0.1V
600
400
200
VS = 3V, VO = 0.3V / 2.7V
0
–40
25
85
TEMPERATURE – °C
125
Figure 10. Open-Loop Gain vs.
Temperature, VS = +3 V
REV. 0
OP191/OP291/OP491
50
89
100
10
0
–10
80
60
40
–20
88
CMRR – dB
CMRR – dB
87
86
20
–30
0
–40
–20
–50
10
100
1k
10k 100k
FREQUENCY – Hz
1M
–40
100
10M
Figure 11. Closed-Loop Gain vs.
Frequency, VS = +3 V
85
1k
10k
100k
FREQUENCY – Hz
1M
84
–40
10M
Figure 12. CMRR vs. Frequency,
VS = +3 V
VS = +3V
±PSRR
VS = +3V
TA = +25°C
140
120
PSRR – dB
+PSRR
60
40
+SR
1.2
111
80
VS = +3V
1.4
112
100
–PSRR
125
1.6
113
160
25
85
TEMPERATURE – °C
Figure 13. CMRR vs. Temperature,
VS = +3 V
SLEW RATE – V/µs
CLOSED-LOOP GAIN – dB
120
20
VS = +3V
CMRR
VS = +3V
TA = +25°C
140
30
PSRR – dB
90
160
VS = +3V
TA = +25°C
40
110
109
1.0
0.8
0.6
0.4
20
0
108
–SR
0.2
–20
–40
100
1k
10k
100k
1M
107
–40
10M
FREQUENCY – Hz
Figure 14. PSRR vs. Frequency,
VS = +3 V
MAXIMUM OUTPUT SWING – Volts
SUPPLY CURRENT/AMPLIFIER – mA
0
–40
125
0.30
0.25
0.20
0.15
0.10
25
85
125
TEMPERATURE – °C
Figure 17. Supply Current vs.
Temperature, VS = +3 V, +5 V, ± 5 V
VIN = +2.8Vp-p
VS = +3V
AV = +1
RL = 100k
2.6
2.4
2.2
85
25
TEMPERATURE – °C
125
Figure 16. Slew Rate vs. Temperature, VS = +3 V
2.8
VS = +3V
REV. 0
85
TEMPERATURE – °C
Figure 15. PSRR vs. Temperature,
VS = +3 V
0.35
0.05
–40
25
MKR: 36.2 nV/√Hz
100
90
2.0
1.8
1.6
10
1.4
0%
1.2
1.0
0.1 0.5 1.0 10 30 50 70 100 150 200 250 300
FREQUENCY – kHz
Figure 18. Maximum Output Swing
vs. Frequency, VS = +3 V
–7–
MKR:
0 Hz
1000 Hz
BW: 2.5kHz
15.0 Hz
Figure 19. Voltage Noise Density,
VS = +3 V to ± 5 V, AVO = 1000
OP191/OP291/OP491–Typical Performance Characteristics
120
70
100
50
VS = +5V
0.10
VCM = 0V
80
40
UNITS
UNITS
0.15
VS = +5V
–40°C < TA < +125°C
BASED ON 600 OP AMPS
30
0.05
VOS – mV
60
VS = +5V
TA = +25°C
BASED ON 600
OP AMPS
60
0
40
20
10
0
0
–.30
–.10
.10
.30
.50
INPUT OFFSET VOLTAGE – mV
Figure 20. OP291 Input Offset Voltage Distribution, VS = +5 V
0
–10
–20
VCM = 0V
–IB
–30
0.8
0.6
0.4
0.2
0
+IB
85
25
TEMPERATURE – °C
VCM = 5V
25
85
TEMPERATURE – °C
OPEN-LOOP GAIN – dB
OUTPUT SWING – Volts
4.85
RL = 2k
4.80
4.75
VS = +5V
4.70
–40
25
85
125
TEMPERATURE – °C
Figure 26. Output Voltage Swing vs.
Temperature, VS = +5 V
6
0
–6
–12
–18
–24
0
5
1
2
3
4
COMMON MODE INPUT VOLTAGE – Volts
Figure 25. Input Bias Current vs.
Common-Mode Voltage,
VS = +5 V
140
VS = +5V
VS = +5V
TA = +25°C
140
4.95
4.90
12
125
160
RL = 100k
18
–30
Figure 24. Input Offset Current vs.
Temperature, VS = +5 V
5.00
24
–36
–0.2
–40
125
Figure 23. Input Bias Current vs.
Temperature, VS = +5 V
VCM = 0V
120
120
100
80
0
60
45
40
90
20
135
0
180
–20
225
–40
100
270
1k
10k
100k
1M
10M
FREQUENCY – Hz
Figure 27. Open-Loop Gain & Phase
vs. Frequency, VS = +5 V
–8–
OPEN-LOOP GAIN – V/mV
I B – nA
10
1.2
1.0
VS = +5V
30
1.4
INPUT BIAS CURRENT – nA
INPUT OFFSET CURRENT – nA
20
125
36
VS = +5V
–IB
85
25
TEMPERATURE – °C
Figure 22. Input Offset Voltage vs.
Temperature, VS = +5 V
1.6
+IB
VS = +5V
VCM = 5V
–40
–40
–0.1
–40
7.0
Figure 21. OP291 Input Offset Voltage Drift Distribution, VS = +5 V
40
30
1.0
2.0
3.0
4.0
5.0
6.0
INPUT OFFSET VOLTAGE – µV/ °C
PHASE SHIFT – Degrees
0
–.50
VCM = +5V
–0.05
20
RL = 100k, VCM = 5V
100
80
60
RL = 100k, VCM = 0V
40
RL = 2k, VCM = 5V
20
RL = 2k, VCM = 0V
0
–40
25
85
TEMPERATURE – °C
125
Figure 28. Open-Loop Gain vs.
Temperature, VS = +5 V
REV. 0
OP191/OP291/OP491
50
160
VS = +5V
TA = +25°C
96
CMRR
VS = +5V
TA = +25°C
140
30
120
20
95
0
–10
CMRR – dB
10
80
60
40
93
92
91
90
–20
20
89
–30
0
88
–40
–20
–50
10
100
1k
10k 100k
FREQUENCY – Hz
1M
10M
Figure 29. Closed-Loop Gain vs.
Frequency, VS = +5 V
10k
100k
1M
FREQUENCY – Hz
0.50
0.5
VS = +5V
+SR
0.35
40
–PSRR
20
+SR
SR – V/µs
SR – V/µs
+PSRR
60
–SR
0.3
0.10
0.1
0.05
VS = +5V
10k
100k
1M
FREQUENCY – Hz
0
–40
10M
Figure 32. PSRR vs. Frequency,
VS = +5 V
25
Figure 33. OP291 Slew Rate vs.
Temperature, VS = +5 V
+ISC, VS = ±5V
16
60
VOLTAGE – µV
–ISC, VS = ±5V
14
+ISC, VS = +3V
10
VS = ±5V
70
–ISC, VS = +3V
50
40
30
10k
20
8
A
10
6
1k
B
VO
10k
VIN = 10Vp-p @ 1kHz
4
–40
0
85
25
TEMPERATURE – °C
125
Figure 35. Short Circuit Current vs.
Temperature, VS = +3 V, +5 V, ± 5 V
0
500
1000
1500
2000
FREQUENCY – Hz
2500
Figure 36. Channel Separation,
VS = ± 5 V
–9–
25
85
TEMPERATURE – °C
125
Figure 34. OP491 Slew Rate vs.
Temperature, VS = +5 V
5.0
80
20
18
0
–40
125
85
TEMPERATURE – °C
MAXIMUM OUTPUT SWING – Volts
1k
0.25
0.15
–20
–40
100
–SR
0.30
0.20
0.2
0
SHORT CIRCUIT CURRENT – mA
125
0.40
0.4
80
REV. 0
85
25
TEMPERATURE – °C
Figure 31. CMRR vs. Temperature,
VS = +5 V
0.45
100
12
86
–40
10M
0.6
120
PSRR – dB
1k
Figure 30. CMRR vs. Frequency,
VS = +5 V
±PSRR
VS = +5V
TA = +25°C
140
P
87
–40
100
160
VS = +5V
94
100
CMRR – dB
CLOSED-LOOP GAIN – dB
40
4.5
4.0
3.5
VIN = +4.8Vp-p
VS = +5V
AV = +1
RL = 100k
4 PARTS
3.0
2.5
2.0
1.5
1.0
0.5
0
0.1 0.5 1.0 10 30 50 70 100 150 200 250 300
FREQUENCY – kHz
Figure 37. Maximum Output Swing
vs. Frequency, VS = +5 V
OP191/OP291/OP491–Typical Performance Characteristics
8
7
INPUT OFFSET VOLTAGE – mV
MAXIMUM OUTPUT SWING – Volts
0.15
VIN = +9.8Vp-p
VS = ±5V
AV = +1
RL = 100k
4 PARTS
9
6
5
4
3
2
40
0.10
VS = ±5V
+IB
VCM = +5V
30
VCM = –5V
–IB
20
0.05
0
10
0
–10
VCM = –5V
–20
VCM = +5V
–0.05
1
50
VS = ±5V
IB – nA
10
–IB
–30
+IB
–40
0
0.1 0.5 1.0 10 30 50 70 100 150 200 250 300
FREQUENCY – kHz
–0.1
–40
0.8
0.6
0.4
0.2
0
12
0
–12
–24
–5 –4 –3 –2 –1 0 1
2 3
4
5
COMMON MODE INPUT VOLTAGE – Volts
125
Figure 42. Input Bias Current vs.
Common-Mode Voltage, VS = ± 5 V
200
70
VS = ±5V
TA = +25°C
0
40
45
30
90
20
10
135
0
180
–10
225
–20
270
–30
10k
100k
1M
10M
FREQUENCY – Hz
Figure 44. Open-Loop Gain & Phase
vs. Frequency, VS = ± 5 V
OPEN-LOOP GAIN – V/mV
50
4.80
4.75
RL = 2k
VS = ±5V
0
–4.75
–4.80
–4.85
RL = 2k
–4.90
RL = 100kΩ
100
80
65
RL = 2kΩ
VS = ±5V
TA = +25°C
30
20
10
0
–10
–20
–30
–40
25
0
–40
125
Figure 43. Output Voltage Swing vs.
Temperature, VS = ± 5 V
40
120
40
25
85
TEMPERATURE – °C
50
160
140
RL = 100k
–5.00
–40
VS = ±5V
180
PHASE SHIFT – Degrees
60
4.85
CLOSED-LOOP GAIN – dB
85
25
TEMPERATURE – °C
4.90
–4.95
–36
Figure 41. Input Offset Current vs.
Temperature, VS = ± 5 V
OPEN-LOOP GAIN – dB
24
VCM = +5V
–0.2
–40
RL = 100k
4.95
OUTPUT VOLTAGE SWING – Volts
INPUT BIAS CURRENT – nA
INPUT OFFSET CURRENT – nA
VCM = –5V
1.0
125
5.00
VS = ±5V
1.2
25
85
TEMPERATURE – °C
Figure 40. Input Bias Current vs.
Temperature, VS = ± 5 V
36
VS = ±5V
1.4
1k
–50
–40
125
Figure 39. Input Offset Voltage vs.
Temperature, VS = ± 5 V
Figure 38. Maximum Output Swing
vs. Frequency, VS = ± 5 V
1.6
25
85
TEMPERATURE – °C
–50
25
85
TEMPERATURE – °C
125
Figure 45. Open-Loop Gain vs.
Temperature, VS = ± 5 V
–10–
10
100
1k
10k 100k
FREQUENCY – Hz
1M
10M
Figure 46. Closed-Loop Gain vs.
Frequency, VS = ± 5 V
REV. 0
OP191/OP291/OP491
102
CMRR
VS = ±5V
TA = +25°C
140
120
101
80
60
120
99
100
98
97
80
60
40
96
20
95
0
94
0
–20
93
–20
–40
100
1k
10k
100k
FREQUENCY – Hz
1M
Figure 47. CMRR vs. Frequency,
VS = ± 5 V
25
85
TEMPERATURE – °C
VS = ±5V
10M
800
+SR
0.5
100
700
–SR
0.4
ZOUT – Ω
SR – V/µs
105
0.3
600
500
400
300
0.2
95
AVCL = 100
200
0.1
25
85
TEMPERATURE – °C
125
AVCL = 10
100
–40
25
85
TEMPERATURE – °C
1.00V
100
125
Figure 51. Slew Rate vs.
Temperature, VS = ± 5 V
1k
100
90
90
INPUT
INPUT
VS = ±5V
RL = 200kΩ
AV = +1V/V
VS = +3V
RL = 200kΩ
10
10
0%
500mV
2.00µs
100mV
OUTPUT
0%
1.00V
Figure 53. Large Signal Transient
Response, VS = +3 V
2.00µs
100mV
Figure 54. Large Signal Transient
Response, VS = ± 5 V
–11–
10k
100k
1M
FREQUENCY – Hz
10M
Figure 52. Output Impedance vs.
Frequency
2.00V
100
OUTPUT
AVCL = +1
0
0
Figure 50. OP291/OP491 PSRR vs.
Temperature, VS = ± 5 V
REV. 0
1M
VS = +3V
TA = +25°C
900
0.6
OP291
PSRR – dB
10k
100k
FREQUENCY – Hz
Figure 49. PSRR vs. Frequency,
VS = ± 5 V
110
90
–40
1k
1k
0.7
VS = ±5V
OP491
–PSRR
–40
100
125
Figure 48. CMRR vs. Temperature,
VS = ± 5 V
115
+PSRR
40
20
92
–40
10M
±PSRR
VS = ±5V
TA = +25°C
140
100
CMRR – dB
CMRR – dB
100
160
VS = ±5V
PSRR – dB
160
OP191/OP291/OP491
FUNCTIONAL DESCRIPTION
The OP191/OP291/OP491 are single supply, micropower
amplifiers featuring rail-to-rail inputs and outputs. In order to
achieve wide input and output ranges, these amplifiers employ
unique input and output stages. As the simplified schematic
shows (Figure 55), the input stage is actually comprised of two
differential pairs, a PNP pair and an NPN pair. These two
stages do not actually work in parallel. Instead, only one or the
other stage is on for any given input signal level. The PNP stage
(transistors Q1 and Q2) is required to ensure that the amplifier
remains in the linear region when the input voltage approaches
and reaches the negative rail. On the other hand, the NPN
stage (transistors Q5 and Q6) is needed for input voltages up to
and including the positive rail.
For the majority of the input common-mode range, the PNP
stage is active, as is evidenced by examining the graph of Input
Bias Current vs. Common-Mode Voltage. Notice that the bias
current switches direction at approximately 1.2 volts to 1.3 volts
below the positive rail. At voltages below this, the bias current
flows out of the OP291, indicating a PNP input stage. Above
this voltage, however, the bias current enters the device,
revealing the NPN stage. The actual mechanism within the
amplifier for switching between the input stages is comprised of
the transistors Q3, Q4, and Q7. As the input common-mode
voltage increases, the emitters of Q1 and Q2 follow that voltage
plus a diode drop. Eventually the emitters of Q1 and Q2 are
high enough to turn Q3 on. This diverts the 8 µA of tail current
away from the PNP input stage, turning it off. Instead, the
current is mirrored through Q4 and Q7 to activate the NPN
input stage.
Notice that the input stage includes 5 kΩ series resistors and
differential diodes, a common practice in bipolar amplifiers to
protect the input transistors from large differential voltages.
These diodes will turn on whenever the differential voltage
exceeds approximately 0.6 V. In this condition, current will
flow between the input pins, limited only by the two 5 kΩ
resistors. Being aware of this characteristic is important in
circuits where the amplifier may be operated open-loop, such as
a comparator. Evaluate each circuit carefully to make sure that
the increase in current does not affect the performance.
The output stage of the OP191 family uses a PNP and an NPN
transistor as do most output stages; however, the output
transistors, Q32 and Q33, are actually connected with their
collectors to the output pin to achieve the rail-to-rail output
swing. As the output voltage approaches either the positive or
negative rail, these transistors begin to saturate. Thus, the final
limit on output voltage is the saturation voltage of these
transistors, which is about 50 mV. The output stage does have
inherent gain arising from the collectors and any external load
impedance. Because of this, the open-loop gain of the amplifier
is dependent on the load resistance.
Input Overvoltage Protection
As with any semiconductor device, whenever the condition
exists for the input to exceed either supply voltage, attention
needs to be paid to the input overvoltage characteristic. When
an overvoltage occurs, the amplifier could be damaged depending on the voltage level and the magnitude of the fault current.
Figure 56 shows the characteristic for the OP191 family. This
graph was generated with the power supplies at ground and a
curve tracer connected to the input. As can be seen, when the
input voltage exceeds either supply by more than 0.6 V, internal
pn-junctions energize allowing current to flow from the input to
the supplies. As described above, the OP291/OP491 does have
5 kΩ resistors in series with each input, which helps limit the
current. Calculating the slope of the current versus voltage in
the graph confirms the 5 kΩ resistor.
Q22
8µA
Q26
–IN
Q32
Q23
Q3
5k
+IN
5k
Q20
Q16
Q5 Q6
Q1 Q2
Q27
Q8
Q10
Q12
Q30
10pF
Q17
Q14
Q21
Q9
Q11
Q13
Q15
Q24
Q18
Q4
Q19
VOUT
Q31
Q25
Q28
Q29
Q33
Q7
Figure 55. Simplified Schematic
–12–
REV. 0
OP191/OP291/OP491
determines the lower limit of their common-mode range. With
these devices, external clamping diodes, with the anode
connected to ground and the cathode to the inputs, prevent
input signal excursions from exceeding the device’s negative
supply (i.e., GND), preventing a condition which could cause
the output voltage to change phase. JFET-input amplifiers may
also exhibit phase reversal, and, if so, a series input resistor is
usually required to prevent it.
IIN
2mA
1mA
–10V
–5V
5V
10V
VIN
The OP191 family is free from reasonable input voltage range
restrictions due to its novel input structure. In fact, the input
signal can exceed the supply voltage by a significant amount
without causing damage to the device. As illustrated in Figure
57, the OP191 family can safely handle a 20 V p-p input signal
on ± 5 V supplies without exhibiting any sign of output voltage
phase reversal or other anomalous behavior. Thus no external
clamping diodes are required.
–1mA
–2mA
Figure 56. Input Overvoltage Characteristics
Overdrive Recovery
This input current is not inherently damaging to the device as
long as it is limited to 5 mA or less. In the case shown, for an
input of 10 V over the supply, the current is limited to 1.8 mA.
If the voltage is large enough to cause more than 5 mA of
current to flow, then an external series resistor should be added.
The size of this resistor is calculated by dividing the maximum
overvoltage by 5 mA and subtracting the internal 5 kΩ resistor.
For example, if the input voltage could reach 100 V, the external
resistor should be (100 V/5 mA) –5 k = 15 kΩ. This resistance
should be placed in series with either or both inputs if they are
subjected to the overvoltages. For more information on general
overvoltage characteristics of amplifiers refer to the 1993 System
Applications Guide, available from the Analog Devices Literature
Center.
The overdrive recovery time of an operational amplifier is the
time required for the output voltage to recover to its linear
region from a saturated condition. This recovery time is
important in applications where the amplifier must recover
quickly after a large transient event, such as a comparator. The
circuit shown in Figure 58 was used to evaluate the OP191
family’s overload recovery time. The OP191 family takes
approximately 8 µs to recover from positive saturation and
approximately 6.5 µs to recover from negative saturation.
Output Voltage Phase Reversal
8
1/2
2 OP291
4
–5V
1
VOUT
100
100
90
90
10
10
0%
0%
TIME – 200µs/DIV
Figure 57. Output Voltage Phase Reversal Behavior
REV. 0
VOUT
R3
10kΩ
5µs
5µs
20mV
20mV
VOUT – 2V/DIV
3
R2
10kΩ
1
Figure 58. Overdrive Recovery Time Test Circuit
VIN – 2.5V/DIV
VIN
20Vp-p
3
1/2
2 OP291
VIN
10V STEP
VS = ±5V
Some operational amplifiers designed for single-supply
operation exhibit an output voltage phase reversal when their
inputs are driven beyond their useful common-mode range.
Typically for single-supply bipolar op amps, the negative supply
+5V
R1
9kΩ
–13–
TIME – 200µs/DIV
OP191/OP291/OP491
APPLICATIONS
Single +3 V Supply, Instrumentation Amplifier
Single Supply RTD Amplifier
The OP291’s low supply current and low voltage operation
make it ideal for battery powered applications such as the
instrumentation amplifier shown in Figure 59. The circuit
utilizes the classic two op amp instrumentation amplifier
topology, with four resistors to set the gain. The equation is
simply that of a noninverting amplifier as shown in the figure.
The two resistors labeled R1 should be closely matched to each
other as well as both resistors labeled R2 to ensure good
common-mode rejection performance. Resistor networks
ensure the closest matching as well as matched drifts for good
temperature stability. Capacitor C1 is included to limit the
bandwidth and, therefore, the noise in sensitive applications.
The value of this capacitor should be adjusted depending on the
desired closed-loop bandwidth of the instrumentation amplifier.
The RC combination creates a pole at a frequency equal to
1/(2 π × R1C1). If AC-CMRR is critical, than a matched
capacitor to C1 should be included across the second resistor
labeled R1.
The circuit in Figure 60 uses three op amps of the OP491 to
develop a bridge configuration for an RTD amplifier that
operates from a single +5 V supply. The circuit takes advantage
of the OP491’s wide output swing range to generate a high
bridge excitation voltage of 3.9 V. In fact, because of the railto-rail output swing, this circuit will work with supplies as low
as 4.0 V. Amplifier A1 servos the bridge to create a constant
excitation current in conjunction with the AD589, a 1.235 V
precision reference. The op amp maintains the reference
voltage across the parallel combination of the 6.19 kΩ and 2.55
MΩ resistor, which generates a 200 µA current source. This
current splits evenly and flows through both halves of the
bridge. Thus, 100 µA flows through the RTD to generate an
output voltage based on its resistance. A 3-wire RTD is used to
balance the line resistance in both 100 Ω legs of the bridge to
improve accuracy.
+3V
8
1/2
OP291
6
4
VIN
3
1/2
2 OP291
R1
7
26.7k
A3
100Ω
RTD
100Ω
6.19k
1/4
OP491
100pF
Figure 59. Single +3 V Supply Instrumentation Amplifier
Because the OP291 accepts rail-to-rail inputs, the input
common-mode range includes both ground and the positive
supply of 3 V. Furthermore, the rail-to-rail output range
ensures the widest signal range possible and maximizes the
dynamic range of the system. Also, with its low supply current
of 300 µA/device, this circuit consumes a quiescent current of
only 600 µA, yet still exhibits a gain bandwidth of 3 MHz.
A question may arise about other instrumentation amplifier
topologies for single supply applications. For example, a
variation on this topology adds a fifth resistor between the two
inverting inputs of the op amps for gain setting. While that
topology works well in dual supply applications, it is inherently
not appropriate for single supply circuits. The same could be
said for the traditional three op amp instrumentation amplifier.
In both cases, the circuits simply will not work in single supply
situations unless a false ground between the supplies is created.
AD589
365
100kΩ
A1
C1
R1
VOUT = (1 + ––– ) V IN
R2
VOUT
1/4
OP491
365
R1
1/4
OP491
A2
2.55M
R2
+5V
26.7k
VOUT
1
R2
GAIN = 274
200Ω
10-TURNS
5
37.4k
100kΩ
0.01pF
NOTE:
ALL RESISTORS 1% OR BETTER
+5V
Figure 60. Single Supply RTD Amplifier
Amplifiers A2 and A3 are configured in the two op amp IA
discussed above. Their resistors are chosen to produce a gain of
274, such that each 1°C increase in temperature results in a
10 mV change in the output voltage, for ease of measurement.
A 0.01 µF capacitor is included in parallel with the 100 kΩ
resistor on amplifier A3 to filter out any unwanted noise from
this high gain circuit. This particular RC combination creates a
pole at 1.6 kHz.
–14–
REV. 0
OP191/OP291/OP491
A +2.5 V Reference from a +3 V Supply
In many single-supply applications, the need for a 2.5 V
reference often arises. Many commercially available monolithic
2.5 V references require at least a minimum operating supply
voltage of 4 V. The problem is exacerbated when the minimum
operating system supply voltage is + 3 V. The circuit illustrated
in Figure 61 is an example of a +2.5 V that operates from a
single +3 V supply. The circuit takes advantage of the OP291’s
rail-to-rail input and output voltage ranges to amplify an
AD589’s 1.235 V output to +2.5 V. The OP291’s low TCVOS
of 1 µV/°C helps to maintain an output voltage temperature
coefficient of less than 200 ppm/°C. The circuit’s overall
temperature coefficient is dominated by R2 and R3’s temperature coefficient. Lower tempco resistors are recommended.
The entire circuit draws less than 420 µA from a +3 V supply
at +25°C.
+3V
R1
17.4kΩ
3
8
1/2
2 OP291
4
AD589
1
+2.5V REF
RESISTORS = 1%, 100ppm/°C
POTENTIOMETER = 10 TURN, 100ppm/°C
R3
100kΩ
R2
100kΩ
P1
5kΩ
The OP291 serves two functions. First, it is required to buffer
the high output impedance of the DAC’s VREF pin, which is on
the order of 10 kΩ. The op amp provides a low impedance
output to drive any following circuitry. Secondly, the op amp
amplifies the output signal to provide a rail-to-rail output swing.
In this particular case, the gain is set to 4.1 to generate a 5.0 V
output when the DAC is at full scale. If other output voltage
ranges are needed, such as 0 to 4.095, the gain can easily be
adjusted by altering the value of the resistors.
A High Side Current Monitor
In the design of power supply control circuits, a great deal of
design effort is focused on ensuring a pass transistor’s long-term
reliability over a wide range of load current conditions. As a
result, monitoring and limiting device power dissipation is of
prime importance in these designs. The circuit illustrated in
Figure 63 is an example of a +5 V, single-supply high side
current monitor that can be incorporated into the design of a
voltage regulator with fold-back current limiting or a high
current power supply with crowbar protection. This design uses
an OP291’s rail-to-rail input voltage range to sense the voltage
drop across a 0.1 Ω current shunt. A p-channel MOSFET used
as the feedback element in the circuit converts the op amp’s
differential input voltage into a current. This current is then
applied to R2 to generate a voltage that is a linear representation
of the load current. The transfer equation for the current
monitor is given by:
R

Monitor Output = R2 ×  SENSE  × I L
 R1 
Figure 61. A +2.5 V Reference that Operates on a Single
+3 V Supply
+5 V Only, 12-Bit DAC Swings Rail-to-Rail
The OP191 family is ideal for use with a CMOS DAC to
generate a digitally controlled voltage with a wide output range.
Figure 62 shows the DAC8043 used in conjunction with the
AD589 to generate a voltage output from 0 V to 1.23 V The
DAC is actually operated in “voltage switching” mode where
the reference is connected to the current output, IOUT, and the
output voltage is taken from the VREF pin. This topology is
inherently noninverting as opposed to the classic current output
mode, which is inverting and, therefore, unsuitable for single
supply.
For the element values shown, the Monitor Output’s transfer
characteristic is 2.5 V/A.
RSENSE
0.1Ω
IL
+5V
+5V
+5V
R1
100Ω
3
8
1/2
OP291
2
4
S
G
M1
3N163
MONITOR
OUTPUT
+5V
1
D
R2
2.49kΩ
8
R1
17.8kΩ
1.23V
VDD
3
IOUT
2
R FB
1
DAC-8043 V
REF
Figure 63. A High-Side Load Current Monitor
+5V
GND CLK SR1 LD
AD589
4
7
6
5
DIGITAL
CONTROL
3
8
1/2
2 OP291
4
1
R3
R2
R4
232Ω
1%
32.4kΩ
1%
100kΩ
1%
D
VOUT = –––– (5V)
4096
Figure 62. +5 V Only, 12-Bit DAC Swings Rail-to-Rail
REV. 0
–15–
OP191/OP291/OP491
390pF
A +3 V, Cold Junction Compensated Thermocouple Amplifier
The OP291’s low supply operation makes it ideal for +3 V
battery powered applications such as the thermocouple amplifier
shown in Figure 64. The K-type thermocouple terminates in an
isothermal block where the junctions’ ambient temperature is
continuously monitored using a simple 1N914 diode. The
diode corrects the thermal EMF generated in the junctions by
feeding a small voltage, scaled by the 1.5 MΩ and 475 Ω
resistors, to the op amp.
37.4kΩ
A1
0.1µF
14
RXA
20kΩ, 1%
13
1/4
OP491 12
0.0047µF
3.3kΩ
A2
10
To calibrate this circuit, immerse the thermocouple measuring
junction in a 0°C ice bath, and adjust the 500 Ω pot to zero
volts out. Next, immerse the thermocouple in a 250°C temperature bath or oven and adjust the Scale Adjust pot for an
output voltage of 2.50 V. Within this temperature range, the
K-type thermocouple is accurate to within ± 3°C without
linearization.
1/4
OP491
9
20kΩ, 1%
475Ω, 1%
8
37.4kΩ, 1%
0.1µF
T1
750pF
20kΩ, 1%
TXA
0.033µF
20kΩ 1%
1:1
20kΩ 1%
1.235V
10k
AD589
ISOTHERMAL
BLOCK
1N914
7.15k
1%
1.5M
1%
ALUMEL
6
24.9k
1%
K-TYPE
THERMOCOUPLE
40.7µV/°C
3
475Ω
1%
ZERO
ADJUST
8
4
2
100k
1
1/4
OP491 3
A4
11
VOUT
OP291
500Ω
10-TURN
11.2mV
+3V OR +5V
4
4.99k
1%
2
COLD
JUNCTIONS
7
SCALE
ADJUST
1.33MΩ 20k
24.3k
1%
AL
CR
CHROMEL
1/4
5 OP491
3.0V
5.1V TO 6.2V
ZENER 5
A3
1
100k
10µF
0.1µF
0V = 0°C
3V = 300°C
2.1k
1%
Figure 64. A 3 V, Cold Junction Compensated Thermocouple Amplifier
Single Supply, Direct Access Arrangement for Modems
An important building block in modems is the telephone line
interface. In the circuit shown in Figure 65, a direct access
arrangement is utilized for transmitting and receiving data from
the telephone line. Amplifier A1 is the receiving amplifier, and
amplifiers A2 and A3 are the transmitters. The forth amplifier,
A4, generates a pseudo ground half way between the supply
voltage and ground. This pseudo ground is needed for the ac
coupled bipolar input signals.
Figure 65. Single Supply Direct Access Arrangement for
Modems
The transmit signal, TXA, is inverted by A2 and then reinverted by A3 to provide a differential drive to the transformer,
where each amplifier supplies half the drive signal. This is
needed because of the smaller swings associated with a single
supply as opposed to a dual supply. Amplifier A1 provides
some gain for the received signal, and it also removes the
transmit signal present at the transformer from the receive
signal. To do this, the drive signal from A2 is also fed to the
noninverting input of A1 to cancel the transmit signal from the
transformer. The OP491’s bandwidth of 3 MHz and rail-to-rail
output swings ensures that it can provide the largest possible
drive to the transformer at the frequency of transmission.
–16–
REV. 0
OP191/OP291/OP491
A +3 V, 50 Hz/60 Hz Active Notch Filter with False Ground
Single-Supply Half-Wave and Full-Wave Rectifiers
To process ac signals in a single-supply system, it is often best to
use a false-ground biasing scheme. A circuit that uses this
approach is illustrated in Figure 66. In this circuit, a falseground circuit biases an active notch filter used to reject 50 Hz/
60 Hz power line interference in portable patient monitoring
equipment. Notch filters are quite commonly used to reject
power line frequency interference which often obscures low
frequency physiological signals, such as heart rates, blood
pressure readings, EEGs, EKGs, etcetera. This notch filter
effectively squelches 60 Hz pickup at a filter Q of 0.75. Substituting 3.16 kΩ resistors for the 2.67 kΩ resistors in the twin-T
section (R1 through R5) configures the active filter to reject
50 Hz interference.
An OP191 family configured as a voltage follower operating on
a single supply can be used as a simple half-wave rectifier in
low-frequency (<2 kHz) applications. A full-wave rectifier can
be configured with a pair of OP291s as illustrated in Figure 67.
The circuit works in the following way: When the input signal is
above 0 V, the output of amplifier A1 follows the input signal.
Since the noninverting input of amplifier A2 is connected to
A1’s output, op amp loop control forces the A2’s inverting input
to the same potential. The result is that both terminals of R1
are equipotential; i.e., no current flows. Since there is no
current flow in R1, the same condition exists upon R2; thus, the
output of the circuit tracks the input signal. When the input
signal is below 0 V, the output voltage of A1 is forced to 0 V.
This condition now forces A2 to operate as an inverting voltage
follower because the noninverting terminal of A2 is at 0 V as
well. The output voltage at VOUTA is then a full-wave rectified
version of the input signal. If needed, a buffered, half-wave
rectified version of the input signal is available at VOUTB.
R2
2.67kΩ
R1
2.67kΩ
+3V
2
VIN
11
1/4
OP491
3
C1
1µF
5
R4
2.67kΩ
R3
2.67kΩ
A1
4
C2
1µF
1
6
1/4
OP491
7
R1
100kΩ
VOUT
+5V
A2
R5
1.33kΩ
(2.67kΩ÷2)
C3
2µF
(1µFx2)
R6
100kΩ
R8
1kΩ
3
VIN
2Vpp
<2kHz
R7
1kΩ
2
6
8
1/2
OP291
R2
100kΩ
1
7
1/2
5 OP291
A2
4 A1
R9
1MΩ
10
C4
1µF
HALF-WAVE
RECTIFIED
OUTPUT
C5
9
0.01µF
1/4
OP491
A3
R10
1MΩ
FULL-WAVE
RECTIFIED
OUTPUT
VOUT B
R11
100kΩ
+3V
VOUT A
8
R12
499Ω
VIN
(1V/DIV)
500mV
1V
100
90
C6
1.5V
1µF
VOUT B
(0.5V/DIV)
10
Figure 66. A +3 V Single-Supply, 50 Hz/60 Hz Active Notch
Filter with False Ground
Amplifier A3 is the heart of the false-ground bias circuit. It
simply buffers the voltage developed by R9 and R10 and is the
reference for the active notch filter. Since the OP491 exhibits a
rail-to-rail input common-mode range, R9 and R10 are chosen
to split the +3 V supply symmetrically. An in-the-loop compensation scheme is used around the OP491 that allows the op amp
to drive C6, a 1 µF capacitor, without oscillation. C6 maintains
a low impedance ac ground over the operating frequency range
of the filter.
The filter section uses a pair of OP491s in a twin-T configuration whose frequency selectivity is very sensitive to the relative
matching of the capacitors and resistors in the twin-T section.
Mylar is the material of choice for the capacitors, and the
relative matching of the capacitors and resistors determines the
filter’s passband symmetry. Using 1% resistors and 5% capacitors produces satisfactory results.
REV. 0
–17–
VOUT A
(0.5V/DIV)
0%
500mV
200µs
TIME – 200µs/DIV
Figure 67. Single-Supply Half-Wave and Full-Wave
Rectifiers Using an OP291
OP191/OP291/OP491
* OP491 SPICE Macro-model
Rev. A, 5/94
*
ARG/ADI
*
* Copyright 1994 by Analog Devices
*
* Refer to “README.DOC” file for License Statement. Use of
* this model indicates your acceptance of the terms and pro* visions in the License Statement.
*
* Node assignments
*
noninverting input
*
inverting input
*
positive supply
*
negative supply
*
output
*
.SUBCKT OP491 1 2
99
50 45
*
* INPUT STAGE
*
I1
99
7
8.06E-6
Q1 6
4
7 QP
Q2 5
3
7 QP
D1 3
99
DX
D2 4
99
DX
D3 3
4
DX
D4 4
3
DX
R1 3
8
5E3
R2 4
2
5E3
R3 5
50
6.4654E3
R4 6
50
6.4654E3
EOS 8
1
POLY(1) (16,39) –0.08E-3 1
IOS 3
4
50E-12
GB1 3
98
(21,98) 50E-9
GB2 4
98
(21,98) 50E-9
CIN 1
2
1E-12
*
* 1ST GAIN STAGE
*
EREF 98
0
(39,0)
1
G1 98
9
(6,5)
31.667E-6
R7 9
98
1E6
EC1 99
10
POLY(1) (99,39) –0.52 1
EC2 11
50
POLY(1) (39,50) –0.52 1
D5 9
10
DX
D6 11
9
DX
*
* 2ND GAIN STAGE AND DOMINANT POLE AT 1.25 Hz
*
G2 98
12
(9,39)
8E-6
R8 12
98
276.311E6
C2 12
98
16E-12
D7 12
13
DX
D8 14
12
DX
V1 99
13
0.58
V2 14
50
0.58
*
* COMMON-MODE STAGE
*
ECM 15
98
POLY(2) (1,39) (2,39) 0 0.5 0.5
R9 15
16
1E6
R10 16
98
10
*
* POLE AT 2.5 MHz
*
G3 98
18
(12,39) 1E-6
R11 18
98
1E6
C4 18
98
63.662E-15
*
* BIAS CURRENT-VS-COMMON-MODE VOLTAGE
*
EP 97
0
(99,0) 1
VB 99
17
1.3
RB 17
50
1E9
E3
19
0
(15,17) 16
D13 19
20
DX
R12 20
0
1E6
G4 98
21
(20,0) 1E-3
R13 21
98
5E3
D14 21
22
DY
E4
97
22
(POLY(1) (99,98) -0.765 1
*
* POLE AT 100 MHz
*
G6 98
40
(18,39) 1E-6
R20 40
98
1E6
C10 40
98
1.592E-15
*
* OUTPUT STAGE
*
RS1 99
39
109.375E3
RS2 39
50
109.375E3
RO1 99
45
41.667
RO2 45
50
41.667
G7 45
99
(99,40) 24E-3
G8 50
45
(40,50) 24E-3
G9 98
60
(45,40) 24E-3
D9 60
61
DX
D10 62
60
DX
V7 61
98
DC 0
V8 98
62
DC 0
FSY 99
50
POLY(2) V7 V8 0.207E-3 1 1
D11 41
45
DZ
D12 45
42
DZ
V5 40
41
0.131
V6 42
40
0.131
.MODEL DX D()
.MODEL DY D(IS=1E-9)
.MODEL DZ D(IS=1E-6)
.MODEL QP PNP(BF=66.667)
.ENDS
–18–
REV. 0
OP191/OP291/OP491
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Epoxy DIP
(P Suffix)
8
8-Lead Narrow-Body SO
(S Suffix)
5
0.280 (7.11)
0.240 (6.10)
PIN 1
1
5
8
4
0.1574 (4.00)
0.1497 (3.80)
PIN 1
0.325 (8.25)
0.300 (7.62)
0.430 (10.92)
0.348 (8.84)
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.195 (4.95)
0.022 (0.558)
0.014 (0.356)
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.1968 (5.00)
0.1890 (4.80)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.0040 (0.10)
0.0500
(1.27)
BSC
8
14
0.280 (7.11)
0.240 (6.10)
1
0.0192 (0.49)
0.0138 (0.35)
7
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558)
0.014 (0.356)
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.2440 (6.20)
0.2284 (5.80)
0.3444 (8.75)
0.3367 (8.55)
0.195 (4.95)
0.115 (2.93)
0.0196 (0.50)
x 45 °
0.0099 (0.25)
0.0688 (1.75)
0.0532 (1.35)
0.015 (0.381)
0.008 (0.204)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
14-Lead TSSOP
(RU Suffix)
8
14
0.173
(4.40)
PIN 1
1
0.251
(6.40)
7
0.1968 (5.00)
0.043
(1.10)
0.0040 (0.10)
0.026
(0.65)
REV. 0
0.0500 (1.27)
0.0160 (0.41)
0.1574 (4.00)
0.1497 (3.80)
1
0.210
(5.33)
MAX
8°
0°
8
PIN 1
7
0.795 (20.19)
0.725 (18.42)
0.0098 (0.25)
0.0075 (0.19)
14-Lead Narrow-Body SO
(S Suffix)
14-Lead Epoxy DIP
(P Suffix)
14
0.0196 (0.50)
x 45 °
0.0099 (0.25)
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
PIN 1
0.2440 (6.20)
0.2284 (5.80)
4
1
0.005
(0.13)
–19–
COPLANARITY
0.003
(0.076) MAX
0.0500
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
8°
0°
0.0500 (1.27)
0.0160 (0.41)
–20–
PRINTED IN U.S.A.
C1970–10–10/94