Ultralow Power, Rail-to-Rail Output Operational Amplifiers OP281/OP481 FEATURES PIN CONFIGURATIONS Low supply current: 4 μA/amplifier maximum Single-supply operation: 2.7 V to 12 V Wide input voltage range Rail-to-rail output swing Low offset voltage: 1.5 mV No phase reversal OUT A 1 8 V+ 2 OP281 7 OUT B +IN A 3 TOP VIEW (Not to Scale) 6 –IN B V– 4 5 +IN B Figure 2. 8-Lead TSSOP (RU Suffix) Applications for these amplifiers include safety monitoring, portable equipment, battery and power supply control, and signal conditioning and interfacing for transducers in very low power systems. The output’s ability to swing rail-to-rail and not increase supply current when the output is driven to a supply voltage enables the OP281/OP481 to be used as comparators in very low power systems. This is enhanced by their fast saturation recovery time. Propagation delays are 250 μs. The OP281/OP481 are specified over the extended industrial temperature range (−40°C to +85°C). The OP281 dual amplifier is available in 8-lead SOIC surface-mount and TSSOP packages. The OP481 quad amplifier is available in narrow 14-lead SOIC and TSSOP packages. 14 OUT D OUT A 1 13 –IN D –IN A 2 +IN A 3 OP481 12 +IN D 11 V– TOP VIEW (Not to Scale) 10 +IN C +IN B 5 –IN B 6 9 –IN C OUT B 7 8 OUT C 00291-003 V+ 4 Figure 3. 14-Lead Narrow-Body SOIC (R Suffix) OUT A 1 14 OUT D –IN A 2 13 –IN D +IN A 3 V+ 4 12 +IN D OP481 TOP VIEW 11 V– (Not to Scale) +IN B 5 –IN B 6 9 –IN C OUT B 7 8 OUT C 10 +IN C 00291-004 Fabricated on Analog Devices’ CBCMOS process, the OP281/OP481 feature a precision bipolar input and an output that swings to within millivolts of the supplies, continuing to sink or source current up to a voltage equal to the supply voltage. 00291-001 1 –IN A 00291-002 OUT A GENERAL DESCRIPTION The OP281 and OP481 are dual and quad ultralow power single-supply amplifiers featuring rail-to-rail outputs. Each operates from supplies as low as 2.0 V and is specified at +3 V and +5 V single supplies as well as ±5 V dual supplies. 7 Figure 1. 8-Lead Narrow-Body SOIC (R Suffix) APPLICATIONS Comparator Battery-powered instrumentation Safety monitoring Remote sensors Low voltage strain gage amplifiers V+ 8 OP281 OUT B TOP VIEW +IN A 3 (Not to Scale) 6 –IN B 5 +IN B V– 4 –IN A 2 Figure 4. 14-Lead TSSOP (RU Suffix) Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©1996–2007 Analog Devices, Inc. All rights reserved. OP281/OP481 TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation .................................................................. 13 Applications....................................................................................... 1 Input Overvoltage Protection ................................................... 13 Pin Configurations ........................................................................... 1 Input Offset Voltage ................................................................... 13 General Description ......................................................................... 1 Input Common-Mode Voltage Range ..................................... 13 Revision History ............................................................................... 2 Capacitive Loading..................................................................... 14 Specifications..................................................................................... 3 Micropower Reference Voltage Generator.............................. 14 Electrical Specifications............................................................... 3 Window Comparator................................................................. 14 Absolute Maximum Ratings............................................................ 6 Low-Side Current Monitor ....................................................... 15 Thermal Resistance ...................................................................... 6 Low Voltage Half-Wave and Full-Wave Rectifiers................. 15 ESD Caution.................................................................................. 6 Battery-Powered Telephone Headset Amplifier..................... 15 Typical Performance Characteristics ............................................. 7 Outline Dimensions ....................................................................... 17 Applications..................................................................................... 13 Ordering Guide .......................................................................... 18 REVISION HISTORY 10/07—Rev. B to Rev. C Updated Format..................................................................Universal Changes to Offset Voltage Drift Condition .................................. 3 Changes to Slew Rate Symbol ......................................................... 5 Changes to Figure 8.......................................................................... 7 Deleted SPICE Macro-Model Section ......................................... 13 Updated Outline Dimensions ....................................................... 17 Changes to Ordering Guide .......................................................... 18 3/03—Rev. A to Rev. B Changes to Features.......................................................................... 1 2/03—Rev. 0 to Rev. A Updated Format..................................................................Universal Deleted OP181 ....................................................................Universal Updated Package Options .................................................Universal Deleted OP181 Pin Configurations ................................................1 Deleted Epoxy DIP Pin Configurations .........................................1 Changes to Absolute Maximum Ratings........................................5 Changes to Ordering Guide .............................................................5 Changes to Input Offset Voltage................................................... 10 Deleted Former Figure 33 ............................................................. 10 Deleted Overdrive Recovery Time Section................................. 11 Deleted Former Figure 36 ............................................................. 11 Deleted 8-Lead and 14-Lead Plastic DIP (N-8 and N-14) Outline Dimensions ....................................................................... 14 Updated Outline Dimensions....................................................... 14 Rev. C | Page 2 of 20 OP281/OP481 SPECIFICATIONS ELECTRICAL SPECIFICATIONS VS = 3.0 V, VCM = 1.5 V, TA = 25°C, unless otherwise noted. Table 1. Parameter INPUT CHARACTERISTICS Offset Voltage 1 Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Ratio Large-Signal Voltage Gain Symbol Condition Min Typ VOS IB IOS CMRR AVO VCM = 0 V to 2.0 V, −40°C ≤ TA ≤ +85°C RL = 1 MΩ, VO = 0.3 V to 2.7 V −40°C ≤ TA ≤ +85°C −40°C to +85°C 3 0.1 0 65 5 2 Unit 1.5 2.5 10 7 2 mV mV nA nA V dB V/mV V/mV μV/°C pA/°C pA/°C 95 13 Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Limit VOH VOL ISC RL = 100 kΩ to GND, −40°C ≤ TA ≤ +85°C RL = 100 kΩ to V+, −40°C ≤ TA ≤ +85°C 2.925 POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier PSRR ISY VS = 2.7 V to 12 V, −40°C ≤ TA ≤ +85°C VO = 0 V −40°C ≤ TA ≤ +85°C 76 SR RL = 100 kΩ, CL = 50 pF AV = 1, VO = 1 V AV = 20, VO = 1 V 25 40 50 65 95 70 V/ms μs μs μs kHz Degrees 0.1 Hz to 10 Hz f = 1 kHz 10 75 <1 μV p-p nV/√Hz pA/√Hz DYNAMIC PERFORMANCE Slew Rate Turn-On Time Saturation Recovery Time Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density 1 ΔVOS/∆T ΔIB/ΔT ΔIOS/ΔT −40°C ≤ TA ≤ +85°C −40°C ≤ TA ≤ +85°C −40°C ≤ TA ≤ +85°C Max GBP φM en p-p en in VOS is tested under a no load condition. Rev. C | Page 3 of 20 10 20 2 2.96 25 ±1.1 95 3 75 4 5 V mV mA dB μA μA OP281/OP481 VS = 5.0 V, VCM = 2.5 V, TA = 25°C, unless otherwise noted. Table 2. Parameter INPUT CHARACTERISTICS Offset Voltage 1 Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Ratio Large-Signal Voltage Gain Symbol Condition Min VOS IB IOS CMRR AVO ΔVOS/ΔT ΔIB/ΔT ΔIOS/ΔT −40°C ≤ TA ≤ +85°C −40°C ≤ TA ≤ +85°C −40°C ≤ TA ≤ +85°C VCM = 0 V to 4.0 V, −40°C ≤ TA ≤ +85°C RL = 1 MΩ, VO = 0.5 V to 4.5 V −40°C ≤ TA ≤ +85°C −40°C to +85°C Typ Max Unit 0.1 1.5 2.5 10 7 4 mV mV nA nA V dB V/mV V/mV μV/°C pA/°C pA/°C 3 0.1 0 65 5 2 90 15 Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Limit VOH VOL ISC RL = 100 kΩ to GND, −40°C ≤ TA ≤ +85°C RL = 100 kΩ to V+, −40°C ≤ TA ≤ +85°C 4.925 POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier PSRR ISY VS = 2.7 V to 12 V, −40°C ≤ TA ≤ +85°C VO = 0 V −40°C ≤ TA ≤ +85°C 76 SR RL = 100 kΩ, CL = 50 pF 27 120 100 74 V/ms μs kHz Degrees 0.1 Hz to 10 Hz f = 1 kHz 10 75 <1 μV p-p nV/√Hz pA/√Hz DYNAMIC PERFORMANCE Slew Rate Saturation Recovery Time Gain Bandwidth Product Phase Margin GBP φM NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density en p-p en in 1 VOS is tested under a no load condition. Rev. C | Page 4 of 20 10 20 2 4.96 25 ±3.5 95 3.2 75 4 5 V mV mA dB μA μA OP281/OP481 VS = ±5.0 V, TA = +25°C, unless otherwise noted. Table 3. Parameter INPUT CHARACTERISTICS Offset Voltage 1 IB IOS Offset Voltage Drift Bias Current Drift Offset Current Drift ΔVOS/ΔT ΔIB/ΔT ΔIOS/ΔT DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density Condition Min VOS Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Large-Signal Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing Short-Circuit Limit POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier 1 Symbol CMRR AVO –40°C ≤ TA ≤ +85°C –40°C ≤ TA ≤ +85°C –40°C ≤ TA ≤ +85°C VCM = –5.0 V to +4.0 V, –40°C ≤ TA ≤ +85°C RL = 1 MΩ, VO = ±4.0 V, –40°C ≤ TA ≤ +85°C –40°C to +85°C Typ Max Unit 0.1 1.5 2.5 10 7 +4 10 20 2 mV mV nA nA V dB V/mV V/mV μV/°C pA/°C pA/°C V mA 3 0.1 –5 65 5 2 95 13 VO ISC RL = 100 kΩ to GND, –40°C ≤ TA ≤ +85°C ±4.925 ±4.98 12 PSRR ISY VS = ±1.35 V to ±6 V, –40°C ≤ TA ≤ +85°C VO = 0 V –40°C ≤ TA ≤ +85°C 76 95 3.3 SR GBP φM RL = 100 kΩ, CL = 50 pF 28 105 75 V/ms kHz Degrees en p-p en 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz 10 85 75 <1 μV p-p nV/√Hz nV/√Hz pA/√Hz in VOS is tested under a no load condition. Rev. C | Page 5 of 20 5 6 dB μA μA OP281/OP481 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 4. Parameter Supply Voltage Input Voltage Differential Input Voltage Output Short-Circuit Duration to GND Storage Temperature Range Operating Temperature Range Junction Temperature Range Lead Temperature Range (Soldering, 60 sec) Rating 16 V GND to VS + 10 V ±3.5 V Indefinite −65°C to +150°C −40°C to +85°C −65°C to +150°C 300°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 5. Thermal Resistance Package Type 8-Lead SOIC (R Suffix) 8-Lead TSSOP (RU Suffix) 14-Lead SOIC (R Suffix) 14-Lead TSSOP (RU Suffix) 1 θJA1 158 240 120 240 θJC 43 43 36 43 Unit °C/W °C/W °C/W °C/W θJA is specified for the worst-case conditions, that is, θJA is specified for device soldered in circuit board for TSSOP and SOIC packages. ESD CAUTION Rev. C | Page 6 of 20 OP281/OP481 TYPICAL PERFORMANCE CHARACTERISTICS 45 0 VS = 2.7V TA = 25°C 40 –1.0 INPUT BIAS CURRENT (nA) 30 25 20 15 10 5 –1.5 –2.0 –2.5 –3.0 –3.5 –4.0 –4.5 0.2 0.4 0.6 0.8 1.0 INPUT OFFSET VOLTAGE (mV) –5.0 –40 Figure 5. Input Offset Voltage Distribution 50 1.0 INPUT BIAS CURRENT (nA) 30 25 20 15 10 120 0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 5 0 0.2 0.4 0.6 0.8 1.0 –3.5 00291-006 –1.0 –0.8 –0.6 –0.4 –0.2 INPUT OFFSET VOLTAGE (mV) 0.5 VS = 5V 1800 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 COMMON-MODE VOLTAGE (V) 4.5 5.0 VS = 5V 0.4 INPUT OFFSET CURRENT (nA) 1600 1400 1200 1000 800 600 400 0.3 0.2 0.1 0 –0.1 –0.2 –0.3 –20 0 20 40 60 80 TEMPERATURE (°C) 100 120 00291-007 200 0 –40 0 Figure 9. Input Bias Current vs. Common-Mode Voltage Figure 6. Input Offset Voltage Distribution INPUT OFFSET VOLTAGE (µV) 100 00291-009 QUANTITY (Amplifiers) 35 2000 20 40 60 80 TEMPERATURE (°C) VS = 5V TA = 25°C 0.5 40 0 0 Figure 8. Input Bias Current vs. Temperature VS = 5V TA = 25°C 45 –20 00291-008 0 00291-005 –1.0 –0.8 –0.6 –0.4 –0.2 Figure 7. Input Offset Voltage vs. Temperature –0.4 –40 –20 0 20 40 60 80 TEMPERATURE (°C) 100 Figure 10. Input Offset Current vs. Temperature Rev. C | Page 7 of 20 120 00291-010 QUANTITY (Amplifiers) 35 0 VS = 5V –0.5 OP281/OP481 10000 70 VS = 3V TA = 25°C SOURCE SINK 10 1 10 100 1000 LOAD CURRENT (µA) 30 20 90 10 135 0 180 –10 225 –20 270 –30 100 00291-011 1 0 45 10k 1M 100k FREQUENCY (Hz) Figure 11. Output Voltage to Supply Rail vs. Load Current 1000 1k 00291-014 OPEN-LOOP GAIN (dB) OUTPUT VOLTAGE (mV) 100 40 PHASE SHIFT (Degrees) 50 1000 0.1 VS = 5V TA = 25°C RL = 100kΩ 60 Figure 14. Open-Loop Gain and Phase vs. Frequency 70 VS = 5V TA = 25°C VS = 3V TA = 25°C RL = 100kΩ 60 10 1 0.1 1 10 100 1000 LOAD CURRENT (µA) 0 30 45 20 90 10 135 0 180 –10 225 –20 270 –30 100 10k 1M 100k FREQUENCY (Hz) Figure 12. Output Voltage to Supply Rail vs. Load Current 1000 1k PHASE SHIFT (Degrees) SINK 40 00291-015 OPEN-LOOP GAIN (dB) SOURCE 00291-012 OUTPUT VOLTAGE (mV) 50 100 Figure 15. Open-Loop Gain and Phase vs. Frequency 70 VS = ±5V TA = 25°C VS = 2.7V TA = 25°C RL = 100kΩ 60 1 0.1 1 10 100 1000 LOAD CURRENT (µA) Figure 13. Output Voltage to Supply Rail vs. Load Current 0 30 45 20 90 10 135 0 180 –10 225 –20 270 –30 100 1k 10k 100k FREQUENCY (Hz) Figure 16. Open-Loop Gain and Phase vs. Frequency Rev. C | Page 8 of 20 1M PHASE SHIFT (Degrees) SINK 40 00291-016 OPEN-LOOP GAIN (dB) SOURCE 10 00291-013 OUTPUT VOLTAGE (mV) 50 100 OP281/OP481 70 90 VS = ±5V TA = 25°C RL = 100kΩ TO GROUND 60 70 0 30 45 20 90 10 135 0 180 –10 225 –20 270 CMRR (dB) PHASE SHIFT (Degrees) 10 0 1M 100k 30 –10 FREQUENCY (Hz) 1k 100 20 80 PSRR (dB) 120 30 10 0 60 40 –10 20 –20 0 –30 –20 10 100 1k 10k 100k VS = ±5V, +5V, +3V, +2.7V TA = 25°C RL = ∞ 140 1M FREQUENCY (Hz) –40 00291-018 CLOSED-LOOP GAIN (dB) 160 40 –40 10M 1M Figure 20. CMRR vs. Frequency VS = 5V TA = 25°C RL = ∞ 50 100k FREQUENCY (Hz) Figure 17. Open-Loop Gain and Phase vs. Frequency 60 10k 10 100 1k 10k 100k 1M 00291-021 10k VS = +3V 40 1000 00291-022 1k 50 20 00291-017 –30 100 VS = +5V 60 00291-020 40 FREQUENCY (Hz) Figure 18. Closed-Loop Gain vs. Frequency Figure 21. PSRR vs. Frequency 50 VS = 5V TA = 25°C MARKER @ 67nV/√Hz SMALL SIGNAL OVERSHOOT (%) 45 (50nV/√Hz/DIV) 40 VS = +5V VIN = ±50mV RL = 100kΩ TA = 25°C –OS +OS 35 30 25 20 15 10 5 0 2 4 6 8 FREQUENCY (kHz) 10 0 10 00291-019 OPEN-LOOP GAIN (dB) 50 TA = 25°C VS = ±5V 80 100 LOAD CAPACITANCE (pF) Figure 22. Small-Signal Overshoot vs. Load Capacitance Figure 19. Voltage Noise Density vs. Frequency Rev. C | Page 9 of 20 OP281/OP481 4.5 VS = 5V VIN = 4V p-p TA = 25°C RL = ∞ 4 VS = 5V 4.0 SUPPLY CURRENT/AMPLIFIER (µA) MAXIMUM OUTPUT SWING (V p-p) 5 3 2 1 3.5 3.0 2.5 2.0 1.5 1.0 100 1k 100k 10k 0 –40 00291-023 0 10 FREQUENCY (Hz) 20 40 60 80 100 120 Figure 26. Supply Current/Amplifier vs. Temperature 3.50 VS = 3V VIN = 2V p-p TA = 25°C RL = ∞ TA = 25°C 3.25 SUPPLY CURRENT/AMPLIFIER (µA) MAXIMUM OUTPUT SWING (V p-p) 0 TEMPERATURE (°C) Figure 23. Maximum Output Swing vs. Frequency 3 –20 00291-026 0.5 2 1 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 1k 100k 10k FREQUENCY (Hz) 0 00291-024 100 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 SUPPLY VOLTAGE (±V) Figure 27. Supply Current/Amplifier vs. Supply Voltage Figure 24. Maximum Output Swing vs. Frequency 4.0 VS = 3V A2 VS = ±2.5V AV = 1 RL = 100kΩ CL = 50pF TA = 25°C 0mV 100 3.0 90 2.5 2.0 1.5 1.0 10 0 –40 50mV –20 0 20 40 60 80 100 TEMPERATURE (°C) 120 100µs Figure 28. Small-Signal Transient Response Figure 25. Supply Current/Amplifier vs. Temperature Rev. C | Page 10 of 20 00291-028 0% 0.5 00291-025 SUPPLY CURRENT/AMPLIFIER (µA) 3.5 00291-027 0.25 0 10 OP281/OP481 100 90 A2 100 90 10 10 0% 0% 50mV 500mV 00291-029 100µs Figure 29. Small-Signal Transient Response A2 100 90 2.5V 1V 1V VS = 5V TA = 25°C 90 10 0% 00291-030 10 100µs A2 100 0% 1V 100µs Figure 31. Large-Signal Transient Response VS = 5V AV = 1 RL = 100kΩ CL = 50pF TA = 25°C 2.5V VS = 2.75V AV = 1 RL = 100kΩ CL = 50pF TA = 25°C 0.5V 00291-031 VS = ±1.35V AV = 1 RL = 100kΩ CL = 50pF TA = 25°C 0mV Figure 30. Large-Signal Transient Response 200µs Figure 32. No Phase Reversal Rev. C | Page 11 of 20 00291-032 A2 OP281/OP481 120 A2 VIN = ±1V p-p AT = 2kHz VS = 5V TA = 25°C RL = ∞ 105 CHANNEL SEPARATION (dB) 0V VS = ±1.35V RL = ∞ 100 90 10 90 75 60 45 30 15 0 0% 50µs –30 100 1k 10k 100k FREQUENCY (Hz) Figure 33. Saturation Recovery Time A2 0V 100 Figure 35. Channel Separation vs. Frequency CIRCUIT = AVOL VS = 2.5V TA = 25°C RL = ∞ 90 10 1V 500mV 100µs 00291-034 0% Figure 34. Saturation Recovery Time Rev. C | Page 12 of 20 1M 00291-035 500mV 00291-033 –15 500mV OP281/OP481 APPLICATIONS The OPx81 family of op amps is comprised of extremely low powered, rail-to-rail output amplifiers, requiring less than 4 μA of quiescent current per amplifier. Many other competitors’ devices may be advertised as low supply current amplifiers but draw significantly more current as the outputs of these devices are driven to a supply rail. The supply current of the OPx81 remains under 4 μA even when the output is driven to either supply rail. Supply currents should meet the specification as long as the inputs and outputs remain within the range of the power supplies. Figure 36 shows a simplified schematic of a single channel for the OPx81. A bipolar differential pair is used in the input stage. PNP transistors are used to allow the input stage to remain linear with the common-mode range extending to ground. This is an important consideration for single-supply applications. The bipolar front end also contributes less noise than a MOS front end with only nanoamps of bias currents. The output of the op amp consists of a pair of CMOS transistors in a common source configuration. This setup allows the output of the amplifier to swing to within millivolts of either supply rail. The headroom required by the output stage is limited by the amount of current being driven into the load. The lower the output current, the closer the output can go to either supply rail. Figure 11, Figure 12, and Figure 13 show the output voltage headroom vs. the load current. This behavior is typical of railto-rail output amplifiers. VCC to the lowest possible input signal excursion and can be found using the following formula: R= V EE − V IN , MIN 0.5 × 10 −3 where: VEE is the negative power supply for the amplifier. VIN, MIN is the lowest input voltage excursion expected. For example, a single channel of the OPx81 should be used with a single-supply voltage of +5 V if the input signal may go as low as −1 V. Because the amplifier is powered from a single supply, VEE is the ground; therefore, the necessary series resistance should be 2 kΩ. INPUT OFFSET VOLTAGE The OPx81 family of op amps was designed for low offset voltages (less than 1 mV). 100kΩ +3V 100kΩ VOUT 100kΩ –0.27V + – OP281 VIN = 1kHz AT 400mV p-p 100kΩ –0.1V 00291-037 THEORY OF OPERATION Figure 37. Single OPx81 Channel Configured as a Difference Amplifier Operating at VCM < 0 V INPUT COMMON-MODE VOLTAGE RANGE The OPx81 is rated with an input common-mode voltage range from VEE to 1 V less than VCC. However, the op amp can operate with a common-mode voltage that is slightly less than VEE. Figure 37 shows a single OPx81 channel configured as a difference amplifier with a single-supply voltage of 3 V. Negative dc voltages are applied at both input terminals, creating a common-mode voltage that is less than ground. A 400 mV p-p input signal is then applied to the noninverting input. Figure 38 shows the resulting input and output waves. Notice how the output of the amplifier also drops slightly negative without distortion. OUT +IN VEE 00291-036 –IN 0.2ms 100 Figure 36. Simplified Schematic of a Single OPx81 Channel VOUT 90 INPUT OVERVOLTAGE PROTECTION This can be done by simply placing a resistor in series with the input to the device. The size of the resistor should be proportional Rev. C | Page 13 of 20 0V VIN 10 0% 0.1V Figure 38. Input and Output Signals with VCM < 0 V 00291-038 The input stage to the OPx81 family of op amps consists of a PNP differential pair. If the base voltage of either of these input transistors drops to more than 0.6 V below the negative supply, the input ESD protection diodes become forward-biased, and large currents begin to flow. In addition to possibly damaging the device, this creates a phase reversal effect at the output. To prevent this, the input current should be limited to less than 0.5 mA. OP281/OP481 CAPACITIVE LOADING WINDOW COMPARATOR Most low supply current amplifiers have difficulty driving capacitive loads due to the higher currents required from the output stage for such loads. Higher capacitance at the output will increase the amount of overshoot and ringing in the amplifier’s step response and may affect the stability of the device. However, through careful design of the output stage and its high phase margin, the OPx81 family can tolerate some degree of capacitive loading. Figure 39 shows the step response of a single channel with a 10 nF capacitor connected at the output. Notice that the overshoot of the output does not exceed more than 10% with such a load, even with a supply voltage of only 3 V. The extremely low power supply current demands of the OPx81 family make it ideal for use in long-life battery-powered applications such as a monitoring system. Figure 41 shows a circuit that uses the OP281 as a window comparator. 3V 3V 3V R1 VH D1 A1 R2 VIN 5.1kΩ OP281-A 10kΩ VOUT Q1 5.1kΩ 2kΩ 3V 3V R3 100 90 D2 VL A2 00291-041 OP281-B R4 Figure 41. Using the OP281 as a Window Comparator 10 00291-039 0% Figure 39. Ringing and Overshoot of the Output of the Amplifier MICROPOWER REFERENCE VOLTAGE GENERATOR Many single-supply circuits are configured with the circuit biased to half of the supply voltage. In these cases, a false ground reference can be created by using a voltage divider buffered by an amplifier. Figure 40 shows the schematic for such a circuit. The two 1 MΩ resistors generate the reference voltage while drawing only 1.5 μA of current from a 3 V supply. A capacitor connected from the inverting terminal to the output of the op amp provides compensation to allow a bypass capacitor to be connected at the reference output. This bypass capacitor helps to establish an ac ground for the reference output. The entire reference generator draws less than 5 μA from a 3 V supply source. 3V TO 12V The threshold limits for the window are set by VH and VL, provided that VH > VL. The output of the first OP281 (A1) will stay at the negative rail, in this case ground, as long as the input voltage is less than VH. Similarly, the output of the second OP281 (A2) will stay at ground as long the input voltage is higher than VL. As long as VIN remains between VL and VH, the outputs of both op amps will be 0 V. With no current flowing in either D1 or D2, the base of Q1 will stay at ground, putting the transistor in cutoff and forcing VOUT to the positive supply rail. If the input voltage rises above VH, the output of A2 stays at ground, but the output of A1 goes to the positive rail and D1 conducts current. This creates a base voltage that turns on Q1 and drives VOUT low. The same condition occurs if VIN falls below VL with A2’s output going high and D2 conducting current. Therefore, VOUT is high if the input voltage is between VL and VH, but low if the input voltage moves outside of that range. The R1 and R2 voltage divider sets the upper window voltage, and the R3 and R4 voltage divider sets the lower voltage for the window. For the window comparator to function properly, VH must be a greater voltage than VL. 10kΩ 0.022µF 2 1MΩ 3 4 1 100Ω VREF 1.5V TO 6V 1µF 00291-040 1MΩ 1µF R2 R1 + R2 VL = R4 R3 + R4 The 2 kΩ resistor connects the input voltage of the input terminals to the op amps. This protects the OP281 from possible excess current flowing into the input stages of the devices. D1 and D2 are small-signal switching diodes (1N4446 or equivalent), and Q1 is a 2N2222 or an equivalent NPN transistor. 8 OP281 VH = Figure 40. Single Channel Configured as a Micropower Bias Voltage Generator Rev. C | Page 14 of 20 OP281/OP481 In the design of power-supply control circuits, a great deal of design effort is focused on ensuring the long-term reliability of a pass transistor over a wide range of load current conditions. As a result, monitoring and limiting device power dissipation is of primary importance in these designs. Figure 42 shows an example of a 5 V, single-supply current monitor that can be incorporated into the design of a voltage regulator with foldback current limiting or a high current power supply with crowbar protection. The design capitalizes on the OPx81’s common-mode range extending to ground. Current is monitored in the power-supply return path, where a 0.1 Ω shunt resistor, RSENSE, creates a very small voltage drop. The voltage at the inverting terminal becomes equal to the voltage at the noninverting terminal through the feedback of Q1, which is a 2N2222 or an equivalent NPN transistor. This makes the voltage drop across R1 equal to the voltage drop across RSENSE. Therefore, the current through Q1 becomes directly proportional to the current through RSENSE, and the output voltage is given by the following equation: R1 R2 100kΩ 100kΩ 3V 3V 2kΩ VIN = 2V p-p A2 A1 OP281-A OP281-B HALF-WAVE RECTIFIED OUTPUT Figure 43. Single-Supply Full-Wave and Half-Wave Rectifiers Using an OP281 100 90 SCALE 0.1V/DIV 10 SCALE 0.1ms/DIV 0% 00291-044 R2 × R SENSE × I L ⎞⎟ VOUT = V EE − ⎛⎜ ⎝ R1 ⎠ The voltage drop across R2 increases as IL increases; therefore, VOUT decreases if a higher supply current is sensed. For the element values shown, the VOUT transfer characteristic is −2.5 V/A, decreasing from VEE. 5V R2 2.49kΩ VOUT Q1 5V 0.1Ω RSENSE SINGLE CHANNEL OPx81 RETURN TO GROUND 00291-042 R1 100Ω FULL-WAVE RECTIFIED OUTPUT 00291-043 LOW-SIDE CURRENT MONITOR Figure 44. Full-Wave Rectified Signal Amplifier A1 is used as a voltage follower that tracks the input voltage only when it is greater than 0 V. This provides a halfwave rectification of the input signal to the noninverting terminal of Amplifier A2. When A1’s output is following the input, the inverting terminal of A2 also follows the input from the virtual ground between the inverting and noninverting terminals of A2. With no potential difference across R1, no current flows through either R1 or R2; therefore, the output of A2 also follows the input. When the input voltage goes below 0 V, the noninverting terminal of A2 becomes 0 V. This makes A2 work as an inverting amplifier with a gain of 1 and provides a full-wave rectified version of the input signal. A 2 kΩ resistor in series with A1’s noninverting input protects the device when the input signal becomes less than ground. BATTERY-POWERED TELEPHONE HEADSET AMPLIFIER Figure 42. Low-Side Load Current Monitor LOW VOLTAGE HALF-WAVE AND FULL-WAVE RECTIFIERS Because of its quick overdrive recovery time, an OP281 can be configured as a full-wave rectifier for low frequency (<500 Hz) applications. Figure 43 shows the schematic. Figure 45 shows how the OP281 can be used as a two-way amplifier in a telephone headset. One side of the OP281 can be used as an amplifier for the microphone, and the other side can be used to drive the speaker. A typical telephone headset uses a 600 Ω speaker and an electret microphone that requires a supply voltage and a biasing resistor. Rev. C | Page 15 of 20 OP281/OP481 0.1µF 11kΩ 3V 3V 2.2kΩ 3V 1µF 1µF 1MΩ MIC OUT OP281-A ELECTRET 1MΩ MIC 1µF 10kΩ audio bandwidth. A 2.2 kΩ resistor is used to bias the electret microphone. This resistor value may vary depending on the specifications of the microphone. The output of the microphone is ac-coupled to the noninverting terminal of the op amp. Two 1 MΩ resistors are used to provide the dc offset for single-supply use. 300kΩ 50kΩ 3V 20kΩ 3V Q1 INPUT 1µF 3V 1µF 10kΩ POT. OP281-B 1µF 1MΩ 20kΩ 600Ω SPEAKER 00291-045 Q2 1MΩ Figure 45. Two-Way Amplifier in a Battery-Powered Telephone Headset The OP281-A op amp provides about 29 dB of gain for audio signals coming from the microphone. The gain is set by the 300 kΩ and 11 kΩ resistors. The gain bandwidth product of the amplifier is 95 kHz, which yields a −3 dB rolloff at 3.4 kHz for the set gain of 28. This is acceptable because telephone audio is band limited for 300 kHz to 3 kHz signals. If higher gain is required for the microphone, an additional gain stage should be used, because adding more gain to the OP281 would limit the The OP281-B amplifier (see Figure 45) can provide up to 15 dB of gain for the headset speaker. Incoming audio signals are ac-coupled to a 10 kΩ potentiometer that is used to adjust the volume. Again, two 1 MΩ resistors provide the dc offset with a 1 μF capacitor establishing an ac ground for the volume-control potentiometer. Because the OP281 is a rail-to-rail output amplifier, it would have difficulty driving a 600 Ω speaker directly. Here, a Class AB buffer is used to isolate the load from the amplifier and to provide the necessary current to drive the speaker. By placing the buffer in the feedback loop of the op amp, crossover distortion can be minimized. Q1 and Q2 should have minimum betas of 100. The 600 Ω speaker is ac-coupled to the emitters to prevent quiescent current from flowing into the speaker. The 1 μF coupling capacitor makes an equivalent high-pass filter cutoff at 265 Hz with a 600 Ω load attached. Again, this does not pose a problem because it is outside the frequency range for telephone audio signals. The circuit in Figure 45 draws around 250 μA of current. The Class AB buffer has a quiescent current of 140 μA, and roughly 100 μA is drawn by the microphone itself. A CR2032 3 V lithium battery has a life expectancy of 160 mA hours, which means this circuit can run continuously for 640 hours on a single battery. Rev. C | Page 16 of 20 OP281/OP481 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 8 5 1 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 6.20 (0.2441) 5.80 (0.2284) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) COPLANARITY 0.10 SEATING PLANE 0.50 (0.0196) 0.25 (0.0099) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-A A CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 012407-A 4.00 (0.1574) 3.80 (0.1497) Figure 46. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 8.75 (0.3445) 8.55 (0.3366) 8 14 1 7 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 0.51 (0.0201) 0.31 (0.0122) 6.20 (0.2441) 5.80 (0.2283) 0.50 (0.0197) 0.25 (0.0098) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 47. 14-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches) Rev. C | Page 17 of 20 060606-A 4.00 (0.1575) 3.80 (0.1496) OP281/OP481 3.10 3.00 2.90 8 5 4.50 4.40 4.30 1 6.40 BSC 4 PIN 1 0.65 BSC 0.15 0.05 1.20 MAX COPLANARITY 0.10 0.30 0.19 SEATING 0.20 PLANE 0.09 8° 0° 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AA Figure 48. 8-Lead Thin Shrink Small Outline Package [TSSOP] (RU-8) Dimensions shown in millimeters 5.10 5.00 4.90 14 8 4.50 4.40 4.30 6.40 BSC 1 7 PIN 1 1.05 1.00 0.80 0.65 BSC 1.20 MAX 0.15 0.05 0.30 0.19 0.20 0.09 SEATING COPLANARITY PLANE 0.10 8° 0° 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 49. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters ORDERING GUIDE Model OP281GRU-REEL OP281GRUZ-REEL 1 OP281GS OP281GS-REEL OP281GS-REEL7 OP281GSZ1 OP281GSZ-REEL1 OP281GSZ-REEL71 OP481GRU-REEL OP481GRUZ-REEL1 OP481GS OP481GS-REEL OP481GS-REEL7 OP481GSZ1 OP481GSZ-REEL1 OP481GSZ-REEL71 1 Temperature Range –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C Package Description 8-Lead TSSOP 8-Lead TSSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 14-Lead TSSOP 14-Lead TSSOP 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N Z = RoHS Compliant Part. Rev. C | Page 18 of 20 Package Option RU-8 RU-8 R-8 R-8 R-8 R-8 R-8 R-8 RU-14 RU-14 R-14 R-14 R-14 R-14 R-14 R-14 OP281/OP481 NOTES Rev. C | Page 19 of 20 OP281/OP481 NOTES ©1996–2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00291-0-10/07(C) Rev. C | Page 20 of 20