CYT6119 400mA CMOS LDO Regulator Features Pin Configuration Typical 175mV dropout voltage at 150mA. ■ Guaranteed 400mA output over the full operating temperature range. ■ Extremely tight load and line regulation. ■ Low temperature coefficient. ■ Current and thermal limiting. ■ No-load stability. ■ Standard SOT-89-3 package. ■ N: 1.GND 2.IN 3.OUT G: 1.OUT 2.GND 3.IN Description The CYT6119 is an efficient linear voltage regulator. It has extra low dropout voltage. At light loads the typical dropout voltage is 15mV, at full load the typical dropout voltage is 600mV. The output voltage accuracy is better than 2%. The CYT6119 has low ground current at 65uA, so it can help prolong battery life. The CYT6119 is specially designed for hand-held, battery-powered devices. Applications Active SCSI terminators. ■ Post regulators for switching supplies. ■ Battery chargers. ■ High-efficiency linear power supplies. ■ Computer motherboard, display, graphic card DC/DC converter, such as 5V to 3.3V, 3.3V to 2.8V or 3.3V to 2.5V. ■ Ordering Information Typical Application ShenZhen CYT IC Design CO ,Ltd -1- CYT6119 400mA CMOS LDO Regulator Absolute Maximum Ratings(1) Operating Ratings(2) Supply Input Voltage (VIN) ..….…6V Power Dissipation (PD) …… Internally Limited(3) Junction Temperature (TJ) ….….. 0°C to +150°C Lead Temperature (soldering, 5 sec) ….…. 260°C Storage Temperature (TS) …. -10°C to +150°C Supply Input Voltage (VIN) ….… +2.8V to +5.5V Junction Temperature (TJ) …….. 0°C to +125°C Package Thermal Resistance ………180°C /W Electrical Characteristics VIN = VOUT + 1.0V; COUT = 4.7µF, IOUT = 10mA; TJ = 25°C;unless otherwise specified. ShenZhen CYT IC Design CO ,Ltd -2- CYT6119 400mA CMOS LDO Regulator Note 1: Exceeding the absolute maximum rating may damage the device. Note 2: The device is not guaranteed to function outside its operating rating. Note 3: The maximum allowable power dissipation at any TA (ambient temperature) is calculated using: PD(MAX) = (TJ(MAX) - TA)/θJA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. See Table 1 and the “Thermal Considerations” section for details. Note 4: Output voltage temperature coefficient is the worst-case voltage change divided by the total temperature range. Note 5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 100µA to 500mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Note 6: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Application Hints Thermal Consideration Like any Low dropout regulator,CYT6119 requires external capacitors to ensure stability. The external capacitors must be carefully selected to ensure the performances.. It is important that the thermal limit of the package should not be exceeded. The CYT6119 has built-in thermal protection. When the thermal limit is exceeded, the IC will enter protection, and the VOUT will be reset to zero. The power dissipation for a given application can be calculated as follows: The Power Dissipation (PD) is PD = IOUT * [VIN – VOUT] The thermal limit of the package is then limited to PD(MAX) = [TJ – TA]/θJA where TJ is the junction temperature, TA is ambient temperature, and θJA is around 180°C/W for CYT6119. CYT6119 is designed to enter thermal protection at 150°C. For example, if TA is 25°C then the max PD is limited to about 0.7W. In other words, if IOUT(MAX) = 400mA, then [VIN – VOUT] can not exceed 1.75V. Input Capacitor: An Input Capacitor of at least 10uF is required. Ceramic or Tantalum can be used. The value can be increased without upper limit. Output Capacitor: An Output Capacitor is required for look stability. It must be located no more than 1cm away from the VOUT pin, and connected directly between VOUT and GND pins. The minimum value is 10uF but once again its value can be increased without limit. ShenZhen CYT IC Design CO ,Ltd -3- CYT6119 400mA CMOS LDO Regulator Typical Performance Characteristics (VIN = 5V, CIN = 1µF, COUT = 10µF, TA=25°C, unless otherwise noted.) ShenZhen CYT IC Design CO ,Ltd -4- CYT6119 400mA CMOS LDO Regulator Outline Drawing for SOT-89 SHENZHEN CHANGYUNTONG IC DESIGE CO. ,LTD. SHENZHEN CHANGYUNTONG IC DESIGN TECHNOLOGY R&D CENTER Head office in china: E201,IER building,south area,shenzhen Hi-Tech industrial park Tel :86-755-26984863 fax :86-755-26984862 office in U.S.A: 7083 hollywood blvd.,suite 180 los angeles,CA 90028 tel :001-323-962-8600 X 269 fax :001-323-962-8300 Company of H.K.: Flat ka shing lou ka wai chnen hung hom hong kong Tel :00852-23305926 fax :00852-23305936 ShenZhen CYT IC Design CO ,Ltd -5-