ETC AT45DB161D-SU-2.5

Features
• Single 2.5V - 3.6V or 2.7V - 3.6V Supply
• Atmel RapidS Serial Interface: 66MHz Maximum Clock Frequency
– SPI Compatible Modes 0 and 3
• User Configurable Page Size
•
•
•
•
•
•
•
•
•
•
•
•
•
– 512-Bytes per Page
– 528-Bytes per Page
– Page Size Can Be Factory Pre-configured for 512-Bytes
Page Program Operation
– Intelligent Programming Operation
– 4,096 Pages (512-/528-Bytes/Page) Main Memory
Flexible Erase Options
– Page Erase (512-Bytes)
– Block Erase (4-Kbytes)
– Sector Erase (128-Kbytes)
– Chip Erase (16-Mbits)
Two SRAM Data Buffers (512-/528-Bytes)
– Allows Receiving of Data while Reprogramming the Flash Array
Continuous Read Capability through Entire Array
– Ideal for Code Shadowing Applications
Low-power Dissipation
– 7mA Active Read Current Typical
– 25µA Standby Current Typical
– 15µA Deep Power Down Typical
Hardware and Software Data Protection Features
– Individual Sector
Sector Lockdown for Secure Code and Data Storage
– Individual Sector
Security: 128-byte Security Register
– 64-byte User Programmable Space
– Unique 64-byte Device Identifier
JEDEC Standard Manufacturer and Device ID Read
100,000 Program/Erase Cycles Per Page Minimum
Data Retention – 20 Years
Industrial Temperature Range
Green (Pb/Halide-free/RoHS Compliant) Packaging Options
1.
16-megabit
2.5V or 2.7V
DataFlash
Atmel AT45DB161D
Description
The Atmel® AT45DB161D is a 2.5V or 2.7V, serial-interface sequential access Flash
memory ideally suited for a wide variety of digital voice-, image-, program code- and
data-storage applications. The AT45DB161D supports Atmel RapidS™ serial interface
for applications requiring very high speed operations. RapidS serial interface is SPI
compatible for frequencies up to 66MHz. Its 17,301,504-bits of memory are organized
as 4,096 pages of 512-bytes or 528-bytes each. In addition to the main memory, the
AT45DB161D also contains two SRAM buffers of 512-/528-bytes each. The buffers
allow the receiving of data while a page in the main Memory is being reprogrammed,
as well as writing a continuous data stream. EEPROM emulation (bit or byte alterability) is easily handled with a self-contained three step read-modify-write
3500N–DFLASH–05/10
operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a
parallel interface, the Atmel® DataFlash® uses a Atmel RapidS™ serial interface to sequentially access its data.
The simple sequential access dramatically reduces active pin count, facilitates hardware layout, increases system
reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many
commercial and industrial applications where high-density, low-pin count, low-voltage and low-power are essential.
To allow for simple in-system reprogrammability, the Atmel AT45DB161D does not require high input voltages for
programming. The device operates from a single power supply, 2.5V to 3.6V or 2.7V to 3.6V, for both the program
and read operations. The AT45DB161D is enabled through the chip select pin (CS) and accessed via a three-wire
interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK).
All programming and erase cycles are self-timed.
2.
Pin Configurations and Pinouts
Figure 2-1.
RDY/BUSY
RESET
WP
NC
NC
VCC
GND
NC
NC
NC
CS
SCK
SI
SO
Figure 2-3.
TSOP Top View: Type 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MLF (VDFN) Top View
SI
SCK
RESET
CS
Note:
2
Figure 2-2.
1
2
3
4
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
1
2
3
4
5
NC
NC
NC
NC
NC
SCK
GND
VCC
NC
NC
CS
RDY/BSY
WP
NC
NC
SO
SI
RESET
NC
NC
NC
NC
NC
NC
A
B
C
D
E
Figure 2-4.
SO
7 GND
6 VCC
5 WP
BGA Package Ball-out
(Top View)
SOIC Top View
8
SI
SCK
RESET
CS
1
2
3
4
8
7
6
5
SO
GND
VCC
WP
1. The metal pad on the bottom of the MLF package is floating. This pad can be a “No Connect” or connected to GND
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
Table 2-1.
Pin Configurations
Symbol
Name and Function
Asserte
d State
Type
CS
Chip Select: Asserting the CS pin selects the device. When the CS pin is deasserted, the
device will be deselected and normally be placed in the standby mode (not Deep Power-Down
mode), and the output pin (SO) will be in a high-impedance state. When the device is
deselected, data will not be accepted on the input pin (SI).
A high-to-low transition on the CS pin is required to start an operation, and a low-to-high
transition is required to end an operation. When ending an internally self-timed operation such
as a program or erase cycle, the device will not enter the standby mode until the completion of
the operation.
Low
Input
SCK
Serial Clock: This pin is used to provide a clock to the device and is used to control the flow of
data to and from the device. Command, address, and input data present on the SI pin is always
latched on the rising edge of SCK, while output data on the SO pin is always clocked out on the
falling edge of SCK.
–
Input
SI
Serial Input: The SI pin is used to shift data into the device. The SI pin is used for all data input
including command and address sequences. Data on the SI pin is always latched on the rising
edge of SCK.
–
Input
SO
Serial Output: The SO pin is used to shift data out from the device. Data on the SO pin is
always clocked out on the falling edge of SCK.
–
Outpu
t
WP
Write Protect: When the WP pin is asserted, all sectors specified for protection by the Sector
Protection Register will be protected against program and erase operations regardless of
whether the Enable Sector Protection command has been issued or not. The WP pin functions
independently of the software controlled protection method. After the WP pin goes low, the
content of the Sector Protection Register cannot be modified.
If a program or erase command is issued to the device while the WP pin is asserted, the device
will simply ignore the command and perform no operation. The device will return to the idle state
once the CS pin has been deasserted. The Enable Sector Protection command and Sector
Lockdown command, however, will be recognized by the device when the WP pin is asserted.
The WP pin is internally pulled-high and may be left floating if hardware controlled protection will
not be used. However, it is recommended that the WP pin also be externally connected to VCC
whenever possible.
Low
Input
RESET
Reset: A low state on the reset pin (RESET) will terminate the operation in progress and reset
the internal state machine to an idle state. The device will remain in the reset condition as long
as a low level is present on the RESET pin. Normal operation can resume once the RESET pin
is brought back to a high level.
The device incorporates an internal power-on reset circuit, so there are no restrictions on the
RESET pin during power-on sequences. If this pin and feature are not utilized it is recommended
that the RESET pin be driven high externally.
Low
Input
RDY/BUSY
Ready/Busy: This open drain output pin will be driven low when the device is busy in an
internally self-timed operation. This pin, which is normally in a high state (through an external
pull-up resistor), will be pulled low during programming/erase operations, compare operations,
and page-to-buffer transfers.
The busy status indicates that the Flash memory array and one of the buffers cannot be
accessed; read and write operations to the other buffer can still be performed.
–
Outpu
t
VCC
Device Power Supply: The VCC pin is used to supply the source voltage to the device.
Operations at invalid VCC voltages may produce spurious results and should not be attempted.
–
Power
GND
Ground: The ground reference for the power supply. GND should be connected to the system
ground.
–
Groun
d
3
3500N–DFLASH–05/10
3.
Block Diagram
FLASH MEMORY ARRAY
WP
PAGE (512-/528-BYTES)
BUFFER 1 (512-/528-BYTES)
SCK
CS
RESET
VCC
GND
RDY/BUSY
4.
BUFFER 2 (512-/528-BYTES)
I/O INTERFACE
SI
SO
Memory Array
To provide optimal flexibility, the memory array of the Atmel ® AT45DB161D is divided into three levels of
granularity comprising of sectors, blocks, and pages. The “Memory Architecture Diagram” illustrates the
breakdown of each level and details the number of pages per sector and block. All program operations to the Atmel
DataFlash® occur on a page by page basis. The erase operations can be performed at the chip, sector, block or
page level.
Memory Architecture Diagram
SECTOR ARCHITECTURE
SECTOR 0b = 248 Pages
126,976-/130,944-bytes
SECTOR 0
BLOCK 0
BLOCK 1
SECTOR 1
SECTOR 0a = 8 Pages
4,096-/4,224-bytes
BLOCK ARCHITECTURE
BLOCK 2
PAGE ARCHITECTURE
8 Pages
PAGE 0
BLOCK 0
Figure 4-1.
PAGE 9
PAGE 14
PAGE 15
BLOCK 62
PAGE 16
BLOCK 63
PAGE 17
BLOCK 64
PAGE 18
SECTOR 14 = 256 Pages
131,072-/135,168-bytes
BLOCK 65
SECTOR 15 = 256 Pages
131,072-/135,168-bytes
BLOCK 510
BLOCK 511
Block = 4,096-/4,224-bytes
4
BLOCK 1
SECTOR 2
BLOCK 33
SECTOR 2 = 256 Pages
131,072-/135,168-bytes
PAGE 8
BLOCK 31
BLOCK 32
PAGE 6
PAGE 7
BLOCK 30
SECTOR 1 = 256 Pages
131,072-/135,168-bytes
PAGE 1
PAGE 4,094
PAGE 4,095
Page = 512-/528-bytes
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
5.
Device Operation
The device operation is controlled by instructions from the host processor. The list of instructions and their
associated opcodes are contained in Table 15-1 on page 27 through Table 15-7 on page 30. A valid instruction
starts with the falling edge of CS followed by the appropriate 8-bit opcode and the desired buffer or main memory
address location. While the CS pin is low, toggling the SCK pin controls the loading of the opcode and the desired
buffer or main memory address location through the SI (serial input) pin. All instructions, addresses, and data are
transferred with the most significant bit (MSB) first.
Buffer addressing for standard Atmel® DataFlash page size (528-bytes) is referenced in the datasheet using the
terminology BFA9 - BFA0 to denote the 10 address bits required to designate a byte address within a buffer. Main
memory addressing is referenced using the terminology PA11 - PA0 and BA9 - BA0, where PA11 - PA0 denotes
the 12 address bits required to designate a page address and BA9 - BA0 denotes the 10 address bits required to
designate a byte address within the page.
For “Power of 2” binary page size (512-bytes) the Buffer addressing is referenced in the datasheet using the
conventional terminology BFA8 - BFA0 to denote the nine address bits required to designate a byte address within
a buffer. Main memory addressing is referenced using the terminology A20 - A0, where A20 - A9 denotes the 12
address bits required to designate a page address and A8 - A0 denotes the nine address bits required to designate
a byte address within a page.
6.
Read Commands
By specifying the appropriate opcode, data can be read from the main memory or from either one of the two SRAM
data buffers. The Atmel DataFlash supports Atmel RapidS™ protocols for Mode 0 and Mode 3. Please refer to the
“Detailed Bit-level Read Timing” diagrams in this datasheet for details on the clock cycle sequences for each
mode.
6.1
Continuous Array Read (Legacy Command: E8H): Up to 66MHz
By supplying an initial starting address for the main memory array, the Continuous Array Read command can be
utilized to sequentially read a continuous stream of data from the device by simply providing a clock signal; no
additional addressing information or control signals need to be provided. The DataFlash incorporates an internal
address counter that will automatically increment on every clock cycle, allowing one continuous read operation
without the need of additional address sequences. To perform a continuous read from the standard DataFlash
page size (528-bytes), an opcode of E8H must be clocked into the device followed by three address bytes (which
comprise the 24-bit page and byte address sequence) and four don’t care bytes. The first 12 bits (PA11 - PA0) of
the 22-bit address sequence specify which page of the main memory array to read, and the last 10 bits (BA9 BA0) of the 22-bit address sequence specify the starting byte address within the page. To perform a continuous
read from the binary page size (512-bytes), the opcode (E8H) must be clocked into the device followed by three
address bytes and four don’t care bytes. The first 12 bits (A20 - A9) of the 21-bits sequence specify which page of
the main memory array to read, and the last nine bits (A8 - A0) of the 21-bits address sequence specify the starting
byte address within the page. The don’t care bytes that follow the address bytes are needed to initialize the read
operation. Following the don’t care bytes, additional clock pulses on the SCK pin will result in data being output on
the SO (serial output) pin.
The CS pin must remain low during the loading of the opcode, the address bytes, the don’t care bytes, and the
reading of data. When the end of a page in main memory is reached during a Continuous Array Read, the device
will continue reading at the beginning of the next page with no delays incurred during the page boundary crossover
(the crossover from the end of one page to the beginning of the next page). When the last bit in the main memory
array has been read, the device will continue reading back at the beginning of the first page of memory. As with
crossing over page boundaries, no delays will be incurred when wrapping around from the end of the array to the
beginning of the array.
5
3500N–DFLASH–05/10
A low-to-high transition on the CS pin will terminate the read operation and tri-state the output pin (SO). The
maximum SCK frequency allowable for the Continuous Array Read is defined by the fCAR1 specification. The
Continuous Array Read bypasses both data buffers and leaves the contents of the buffers unchanged.
6.2
Continuous Array Read (High Frequency Mode: 0BH): Up to 66MHz
This command can be used with the serial interface to read the main memory array sequentially in high speed
mode for any clock frequency up to the maximum specified by fCAR1. To perform a continuous read array with the
page size set to 528-bytes, the CS must first be asserted then an opcode 0BH must be clocked into the device
followed by three address bytes and a dummy byte. The first 12 bits (PA11 - PA0) of the 22-bit address sequence
specify which page of the main memory array to read, and the last 10 bits (BA9 - BA0) of the 22-bit address
sequence specify the starting byte address within the page. To perform a continuous read with the page size set to
512-bytes, the opcode, 0BH, must be clocked into the device followed by three address bytes (A20 - A0) and a
dummy byte. Following the dummy byte, additional clock pulses on the SCK pin will result in data being output on
the SO (serial output) pin.
The CS pin must remain low during the loading of the opcode, the address bytes, and the reading of data. When
the end of a page in the main memory is reached during a Continuous Array Read, the device will continue reading
at the beginning of the next page with no delays incurred during the page boundary crossover (the crossover from
the end of one page to the beginning of the next page). When the last bit in the main memory array has been read,
the device will continue reading back at the beginning of the first page of memory. As with crossing over page
boundaries, no delays will be incurred when wrapping around from the end of the array to the beginning of the
array. A low-to-high transition on the CS pin will terminate the read operation and tri-state the output pin (SO). The
maximum SCK frequency allowable for the Continuous Array Read is defined by the fCAR1 specification. The
Continuous Array Read bypasses both data buffers and leaves the contents of the buffers unchanged.
6.3
Continuous Array Read (Low Frequency Mode: 03H): Up to 33MHz
This command can be used with the serial interface to read the main memory array sequentially without a dummy
byte up to maximum frequencies specified by fCAR2. To perform a continuous read array with the page size set to
528-bytes, the CS must first be asserted then an opcode, 03H, must be clocked into the device followed by three
address bytes (which comprise the 24-bit page and byte address sequence). The first 12 bits (PA11 - PA0) of the
22-bit address sequence specify which page of the main memory array to read, and the last 10 bits (BA9 - BA0) of
the 22-bit address sequence specify the starting byte address within the page. To perform a continuous read with
the page size set to 512-bytes, the opcode, 03H, must be clocked into the device followed by three address bytes
(A20 - A0). Following the address bytes, additional clock pulses on the SCK pin will result in data being output on
the SO (serial output) pin.
The CS pin must remain low during the loading of the opcode, the address bytes, and the reading of data. When
the end of a page in the main memory is reached during a Continuous Array Read, the device will continue reading
at the beginning of the next page with no delays incurred during the page boundary crossover (the crossover from
the end of one page to the beginning of the next page). When the last bit in the main memory array has been read,
the device will continue reading back at the beginning of the first page of memory. As with crossing over page
boundaries, no delays will be incurred when wrapping around from the end of the array to the beginning of the
array. A low-to-high transition on the CS pin will terminate the read operation and tri-state the output pin (SO). The
Continuous Array Read bypasses both data buffers and leaves the contents of the buffers unchanged.
6
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
6.4
Main Memory Page Read
A main memory page read allows the user to read data directly from any one of the 4,096 pages in the main
memory, bypassing both of the data buffers and leaving the contents of the buffers unchanged. To start a page
read from the standard Atmel® DataFlash page size (528-bytes), an opcode of D2H must be clocked into the
device followed by three address bytes (which comprise the 24-bit page and byte address sequence) and four
don’t care bytes. The first 12 bits (PA11 - PA0) of the 22-bit address sequence specify the page in main memory to
be read, and the last 10 bits (BA9 - BA0) of the 22-bit address sequence specify the starting byte address within
that page. To start a page read from the binary page size (512-bytes), the opcode D2H must be clocked into the
device followed by three address bytes and four don’t care bytes. The first 12 bits (A20 - A9) of the 21-bits
sequence specify which page of the main memory array to read, and the last nine bits (A8 - A0) of the 21-bits
address sequence specify the starting byte address within the page. The don’t care bytes that follow the address
bytes are sent to initialize the read operation. Following the don’t care bytes, additional pulses on SCK result in
data being output on the SO (serial output) pin. The CS pin must remain low during the loading of the opcode, the
address bytes, the don’t care bytes, and the reading of data. When the end of a page in main memory is reached,
the device will continue reading back at the beginning of the same page. A low-to-high transition on the CS pin will
terminate the read operation and tri-state the output pin (SO). The maximum SCK frequency allowable for the Main
Memory Page Read is defined by the fSCK specification. The Main Memory Page Read bypasses both data buffers
and leaves the contents of the buffers unchanged.
6.5
Buffer Read
The SRAM data buffers can be accessed independently from the main memory array, and utilizing the Buffer Read
Command allows data to be sequentially read directly from the buffers. Four opcodes, D4H or D1H for buffer 1 and
D6H or D3H for buffer 2 can be used for the Buffer Read Command. The use of each opcode depends on the
maximum SCK frequency that will be used to read data from the buffer. The D4H and D6H opcode can be used at
any SCK frequency up to the maximum specified by fCAR1. The D1H and D3H opcode can be used for lower
frequency read operations up to the maximum specified by fCAR2.
To perform a buffer read from the standard DataFlash buffer (528-bytes), the opcode must be clocked into the
device followed by three address bytes comprised of 14 don’t care bits and 10 buffer address bits (BFA9 - BFA0).
To perform a buffer read from the binary buffer (512-bytes), the opcode must be clocked into the device followed
by three address bytes comprised of 15 don’t care bits and nine buffer address bits (BFA8 - BFA0). Following the
address bytes, one don’t care byte must be clocked in to initialize the read operation. The CS pin must remain low
during the loading of the opcode, the address bytes, the don’t care bytes, and the reading of data. When the end of
a buffer is reached, the device will continue reading back at the beginning of the buffer. A low-to-high transition on
the CS pin will terminate the read operation and tri-state the output pin (SO).
7
3500N–DFLASH–05/10
7.
Program and Erase Commands
7.1
Buffer Write
Data can be clocked in from the input pin (SI) into either buffer 1 or buffer 2. To load data into the standard Atmel®
DataFlash buffer (528-bytes), a 1-byte opcode, 84H for buffer 1 or 87H for buffer 2, must be clocked into the
device, followed by three address bytes comprised of 14 don’t care bits and 10 buffer address bits (BFA9 - BFA0).
The 10 buffer address bits specify the first byte in the buffer to be written. To load data into the binary buffers (512bytes each), a 1-byte opcode 84H for buffer 1 or 87H for buffer 2, must be clocked into the device, followed by
three address bytes comprised of 15 don’t care bits and nine buffer address bits (BFA8 - BFA0). The nine buffer
address bits specify the first byte in the buffer to be written. After the last address byte has been clocked into the
device, data can then be clocked in on subsequent clock cycles. If the end of the data buffer is reached, the device
will wrap around back to the beginning of the buffer. Data will continue to be loaded into the buffer until a low-tohigh transition is detected on the CS pin.
7.2
Buffer to Main Memory Page Program with Built-in Erase
Data written into either buffer 1 or buffer 2 can be programmed into the main memory. A 1-byte opcode, 83H for
buffer 1 or 86H for buffer 2, must be clocked into the device. For the standard DataFlash page size (528-bytes), the
opcode must be followed by three address bytes consist of two don’t care bits, 12 page address bits (PA11 - PA0)
that specify the page in the main memory to be written and 10 don’t care bits. To perform a buffer to main memory
page program with built-in erase for the binary page size (512-bytes), the opcode 83H for buffer 1 or 86H for buffer
2, must be clocked into the device followed by three address bytes consisting of three don’t care bits 12 page
address bits (A20 - A9) that specify the page in the main memory to be written and nine don’t care bits. When a
low-to-high transition occurs on the CS pin, the part will first erase the selected page in main memory (the erased
state is a logic 1) and then program the data stored in the buffer into the specified page in main memory. Both the
erase and the programming of the page are internally self-timed and should take place in a maximum time of tEP.
During this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
7.3
Buffer to Main Memory Page Program without Built-in Erase
A previously-erased page within main memory can be programmed with the contents of either buffer 1 or buffer 2.
A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2, must be clocked into the device. For the standard DataFlash
page size (528-bytes), the opcode must be followed by three address bytes consist of two don’t care bits, 12 page
address bits (PA11 - PA0) that specify the page in the main memory to be written and 10 don’t care bits. To
perform a buffer to main memory page program without built-in erase for the binary page size (512-bytes), the
opcode 88H for buffer 1 or 89H for buffer 2, must be clocked into the device followed by three address bytes
consisting of three don’t care bits, 12 page address bits (A20 - A9) that specify the page in the main memory to be
written and nine don’t care bits. When a low-to-high transition occurs on the CS pin, the part will program the data
stored in the buffer into the specified page in the main memory. It is necessary that the page in main memory that
is being programmed has been previously erased using one of the erase commands (Page Erase or Block Erase).
The programming of the page is internally self-timed and should take place in a maximum time of tP. During this
time, the status register and the RDY/BUSY pin will indicate that the part is busy.
7.4
Page Erase
The Page Erase command can be used to individually erase any page in the main memory array allowing the
Buffer to Main Memory Page Program to be utilized at a later time. To perform a page erase in the standard
DataFlash page size (528-bytes), an opcode of 81H must be loaded into the device, followed by three address
bytes comprised of two don’t care bits, 12 page address bits (PA11 - PA0) that specify the page in the main
memory to be erased and 10 don’t care bits. To perform a page erase in the binary page size (512-bytes), the
opcode 81H must be loaded into the device, followed by three address bytes consist of three don’t care bits, 12
8
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
page address bits (A20 - A9) that specify the page in the main memory to be erased and nine don’t care bits. When
a low-to-high transition occurs on the CS pin, the part will erase the selected page (the erased state is a logical 1).
The erase operation is internally self-timed and should take place in a maximum time of tPE. During this time, the
status register and the RDY/BUSY pin will indicate that the part is busy.
7.5
Block Erase
A block of eight pages can be erased at one time. This command is useful when large amounts of data has to be
written into the device. This will avoid using multiple Page Erase Commands. To perform a block erase for the
standard Atmel DataFlash page size (528-bytes), an opcode of 50H must be loaded into the device, followed by
three address bytes comprised of two don’t care bits, nine page address bits (PA11 -PA3) and 13 don’t care bits.
The nine page address bits are used to specify which block of eight pages is to be erased. To perform a block
erase for the binary page size (512-bytes), the opcode 50H must be loaded into the device, followed by three
address bytes consisting of three don’t care bits, nine page address bits (A20 - A12) and 12 don’t care bits. The
nine page address bits are used to specify which block of eight pages is to be erased. When a low-to-high
transition occurs on the CS pin, the part will erase the selected block of eight pages. The erase operation is
internally self-timed and should take place in a maximum time of tBE. During this time, the status register and the
RDY/BUSY pin will indicate that the part is busy.
Table 7-1.
7.6
Block Erase Addressing
PA11/
A20
PA10/
A19
PA9/
A18
PA8/
A17
PA7/
A16
PA6/
A15
PA5/
A14
PA4/
A13
PA3/
A12
PA2/
A11
PA1/
A10
PA0/
A9
Block
0
0
0
0
0
0
0
0
0
X
X
X
0
0
0
0
0
0
0
0
0
1
X
X
X
1
0
0
0
0
0
0
0
1
0
X
X
X
2
0
0
0
0
0
0
0
1
1
X
X
X
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
0
0
X
X
X
508
1
1
1
1
1
1
1
0
1
X
X
X
509
1
1
1
1
1
1
1
1
0
X
X
X
510
1
1
1
1
1
1
1
1
1
X
X
X
511
Sector Erase
The Sector Erase command can be used to individually erase any sector in the main memory. There are 16
sectors and only one sector can be erased at one time. To perform sector 0a or sector 0b erase for the standard
DataFlash page size (528-bytes), an opcode of 7CH must be loaded into the device, followed by three address
bytes comprised of two don’t care bits, nine page address bits (PA11 - PA3) and 13 don’t care bits. To perform a
sector 1-15 erase, the opcode 7CH must be loaded into the device, followed by three address bytes comprised of
two don’t care bits, four page address bits (PA11 - PA8) and 18 don’t care bits. To perform sector 0a or sector 0b
erase for the binary page size (512-bytes), an opcode of 7CH must be loaded into the device, followed by three
address bytes comprised of three don’t care bit and nine page address bits (A20 - A12) and 12 don’t care bits. To
perform a sector 1-15 erase, the opcode 7CH must be loaded into the device, followed by three address bytes
comprised of 3 don’t care bit and four page address bits (A20 - A17) and 17 don’t care bits. The page address bits
are used to specify any valid address location within the sector which is to be erased. When a low-to-high transition
occurs on the CS pin, the part will erase the selected sector. The erase operation is internally self-timed and should
9
3500N–DFLASH–05/10
take place in a maximum time of tSE. During this time, the status register and the RDY/BUSY pin will indicate that
the part is busy.
Table 7-2.
7.7
Sector Erase Addressing
PA11/
A20
PA10/
A19
PA9/
A18
PA8/
A17
PA7/
A16
PA6/
A15
PA5/
A14
PA4/
A13
PA3/
A12
PA2/
A11
PA1/
A10
PA0/
A9
Sector
0
0
0
0
0
0
0
0
0
X
X
X
0a
0
0
0
0
0
0
0
0
1
X
X
X
0b
0
0
0
1
X
X
X
X
X
X
X
X
1
0
0
1
0
X
X
X
X
X
X
X
X
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
0
0
X
X
X
X
X
X
X
X
12
1
1
0
1
X
X
X
X
X
X
X
X
13
1
1
1
0
X
X
X
X
X
X
X
X
14
1
1
1
1
X
X
X
X
X
X
X
X
15
Chip Erase(1)
The entire main memory can be erased at one time by using the Chip Erase command.
To execute the Chip Erase command, a 4-byte command sequence C7H, 94H, 80H and 9AH must be clocked into
the device. Since the entire memory array is to be erased, no address bytes need to be clocked into the device,
and any data clocked in after the opcode will be ignored. After the last bit of the opcode sequence has been
clocked in, the CS pin can be deasserted to start the erase process. The erase operation is internally self-timed
and should take place in a time of tCE. During this time, the Status Register will indicate that the device is busy.
The Chip Erase command will not affect sectors that are protected or locked down; the contents of those sectors
will remain unchanged. Only those sectors that are not protected or locked down will be erased.
Note:
1. Refer to the errata regarding Chip Erase on page 53.
The WP pin can be asserted while the device is erasing, but protection will not be activated until the internal erase
cycle completes.
Table 7-3.
Chip Erase Command
Command
Byte 1
Byte 2
Byte 3
Byte 4
Chip Erase
C7H
94H
80H
9AH
Figure 7-1.
Chip Erase
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Each transition
represents eight bits
Note:
10
1. Refer to the errata regarding Chip Erase on page 53
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
7.8
Main Memory Page Program Through Buffer
This operation is a combination of the Buffer Write and Buffer to Main Memory Page Program with Built-in Erase
operations. Data is first clocked into buffer 1 or buffer 2 from the input pin (SI) and then programmed into a
specified page in the main memory. To perform a main memory page program through buffer for the standard
Atmel® DataFlash page size (528-bytes), a 1-byte opcode, 82H for buffer 1 or 85H for buffer 2, must first be
clocked into the device, followed by three address bytes. The address bytes are comprised of two don’t care bits,
12 page address bits, (PA11 - PA0) that select the page in the main memory where data is to be written, and 10
buffer address bits (BFA9 - BFA0) that select the first byte in the buffer to be written. To perform a main memory
page program through buffer for the binary page size (512-bytes), the opcode 82H for buffer 1 or 85H for buffer 2,
must be clocked into the device followed by three address bytes consisting of three don’t care bits, 12 page
address bits (A20 - A9) that specify the page in the main memory to be written, and 9 buffer address bits (BFA8 BFA0) that selects the first byte in the buffer to be written. After all address bytes are clocked in, the part will take
data from the input pins and store it in the specified data buffer. If the end of the buffer is reached, the device will
wrap around back to the beginning of the buffer. When there is a low-to-high transition on the CS pin, the part will
first erase the selected page in main memory to all 1s and then program the data stored in the buffer into that
memory page. Both the erase and the programming of the page are internally self-timed and should take place in a
maximum time of tEP. During this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
8.
Sector Protection
Two protection methods, hardware and software controlled, are provided for protection against inadvertent or
erroneous program and erase cycles. The software controlled method relies on the use of software commands to
enable and disable sector protection while the hardware controlled method employs the use of the Write Protect
(WP) pin. The selection of which sectors that are to be protected or unprotected against program and erase
operations is specified in the nonvolatile Sector Protection Register. The status of whether or not sector protection
has been enabled or disabled by either the software or the hardware controlled methods can be determined by
checking the Status Register.
8.1
Software Sector Protection
8.1.1
Enable Sector Protection Command
Sectors specified for protection in the Sector Protection Register can be protected from program and erase
operations by issuing the Enable Sector Protection command. To enable the sector protection using the software
controlled method, the CS pin must first be asserted as it would be with any other command. Once the CS pin has
been asserted, the appropriate 4-byte command sequence must be clocked in via the input pin (SI). After the last
bit of the command sequence has been clocked in, the CS pin must be deasserted after which the sector
protection will be enabled.
Table 8-1.
Enable Sector Protection Command
Command
Enable Sector Protection
Figure 8-1.
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
7FH
A9H
Enable Sector Protection
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Each transition
represents eight bits
11
3500N–DFLASH–05/10
8.1.2
Disable Sector Protection Command
To disable the sector protection using the software controlled method, the CS pin must first be asserted as it would
be with any other command. Once the CS pin has been asserted, the appropriate 4-byte sequence for the Disable
Sector Protection command must be clocked in via the input pin (SI). After the last bit of the command sequence
has been clocked in, the CS pin must be deasserted after which the sector protection will be disabled. The WP pin
must be in the deasserted state; otherwise, the Disable Sector Protection command will be ignored.
Table 8-2.
Disenable Sector Protection Command
Command
Disable Sector Protection
Figure 8-2.
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
7FH
9AH
Disable Sector Protection
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Each transition
represents eight bits
8.1.3
Various Aspects About Software Controlled Protection
Software controlled protection is useful in applications in which the WP pin is not or cannot be controlled by a host
processor. In such instances, the WP pin may be left floating (the WP pin is internally pulled high) and sector
protection can be controlled using the Enable Sector Protection and Disable Sector Protection commands.
If the device is power cycled, then the software controlled protection will be disabled. Once the device is powered
up, the Enable Sector Protection command should be reissued if sector protection is desired and if the WP pin is
not used.
9.
Hardware Controlled Protection
Sectors specified for protection in the Sector Protection Register and the Sector Protection Register itself can be
protected from program and erase operations by asserting the WP pin and keeping the pin in its asserted state.
The Sector Protection Register and any sector specified for protection cannot be erased or reprogrammed as long
as the WP pin is asserted. In order to modify the Sector Protection Register, the WP pin must be deasserted. If the
WP pin is permanently connected to GND, then the content of the Sector Protection Register cannot be changed.
If the WP pin is deasserted, or permanently connected to VCC, then the content of the Sector Protection Register
can be modified.
The WP pin will override the software controlled protection method but only for protecting the sectors. For example,
if the sectors were not previously protected by the Enable Sector Protection command, then simply asserting the
WP pin would enable the sector protection within the maximum specified t WPE time. When the WP pin is
deasserted; however, the sector protection would no longer be enabled (after the maximum specified tWPD time) as
long as the Enable Sector Protection command was not issued while the WP pin was asserted. If the Enable
Sector Protection command was issued before or while the WP pin was asserted, then simply deasserting the WP
pin would not disable the sector protection. In this case, the Disable Sector Protection command would need to be
issued while the WP pin is deasserted to disable the sector protection. The Disable Sector Protection command is
also ignored whenever the WP pin is asserted.
A noise filter is incorporated to help protect against spurious noise that may inadvertently assert or deassert the
WP pin.
12
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
The table below details the sector protection status for various scenarios of the WP pin, the Enable Sector
Protection command, and the Disable Sector Protection command.
Figure 9-1.
WP Pin and Protection Status
1
3
2
WP
WP Pin and Protection Status
Table 9-1.
9.1
Enable Sector Protection Command
Disable Sector
Protection Command
Sector
Protection
Status
Sector
Protection
Register
High
Command Not Issued Previously
–
Issue Command
X
Issue Command
–
Disabled
Disabled
Enabled
Read/Write
Read/Write
Read/Write
2
Low
X
X
Enabled
Read Only
3
High
Command Issued During Period 1 or 2
–
Issue Command
Not Issued Yet
Issue Command
–
Enabled
Disabled
Enabled
Read/Write
Read/Write
Read/Write
Time
Period
WP Pin
1
Sector Protection Register
The nonvolatile Sector Protection Register specifies which sectors are to be protected or unprotected with either
the software or hardware controlled protection methods. The Sector Protection Register contains 16-bytes of data,
of which byte locations 0 through 15 contain values that specify whether sectors 0 through 15 will be protected or
unprotected. The Sector Protection Register is user modifiable and must first be erased before it can be
reprogrammed. Table 9-3 illustrates the format of the Sector Protection Register.:
Table 9-2.
Sector Protection Register
Sector Number
0 (0a, 0b)
1 to 15
Protected
FFH
See Table 9-3
Unprotected
Table 9-3.
00H
Sector 0 (0a, 0b)
0a
0b
(Page 0-7)
(Page 8-255)
Bit 7, 6
Bit 5, 4
Bit 3, 2
Bit 1, 0
Data
Value
Sectors 0a, 0b Unprotected
00
00
xx
xx
0xH
Protect Sector 0a
11
00
xx
xx
CxH
00
11
xx
xx
3xH
11
11
xx
xx
FxH
Protect Sector 0b (Page 8-255)
Protect Sectors 0a (Page 0-7), 0b (Page 8-255)
Note:
(1)
1. The default value for bytes 0 through 15 when shipped from Atmel is 00H
x = don’t care
13
3500N–DFLASH–05/10
9.1.1
Erase Sector Protection Register Command
In order to modify and change the values of the Sector Protection Register, it must first be erased using the Erase
Sector Protection Register command.
To erase the Sector Protection Register, the CS pin must first be asserted as it would be with any other command.
Once the CS pin has been asserted, the appropriate 4-byte opcode sequence must be clocked into the device via
the SI pin. The 4-byte opcode sequence must start with 3DH and be followed by 2AH, 7FH, and CFH. After the last
bit of the opcode sequence has been clocked in, the CS pin must be deasserted to initiate the internally self-timed
erase cycle. The erasing of the Sector Protection Register should take place in a time of tPE, during which time the
Status Register will indicate that the device is busy. If the device is powered-down before the completion of the
erase cycle, then the contents of the Sector Protection Register cannot be guaranteed.
The Sector Protection Register can be erased with the sector protection enabled or disabled. Since the erased
state (FFH) of each byte in the Sector Protection Register is used to indicate that a sector is specified for
protection, leaving the sector protection enabled during the erasing of the register allows the protection scheme to
be more effective in the prevention of accidental programming or erasing of the device. If for some reason an
erroneous program or erase command is sent to the device immediately after erasing the Sector Protection
Register and before the register can be reprogrammed, then the erroneous program or erase command will not be
processed because all sectors would be protected.
Table 9-4.
Erase Sector Protection Register Command
Command
Erase Sector Protection Register
Figure 9-2.
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
7FH
CFH
Erase Sector Protection Register
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Each transition
represents eight bits
9.1.2
Program Sector Protection Register Command
Once the Sector Protection Register has been erased, it can be reprogrammed using the Program Sector
Protection Register command.
To program the Sector Protection Register, the CS pin must first be asserted and the appropriate 4-byte opcode
sequence must be clocked into the device via the SI pin. The 4-byte opcode sequence must start with 3DH and be
followed by 2AH, 7FH, and FCH. After the last bit of the opcode sequence has been clocked into the device, the
data for the contents of the Sector Protection Register must be clocked in. As described in Section 9.1, the Sector
Protection Register contains 16-bytes of data, so 16-bytes must be clocked into the device. The first byte of data
corresponds to sector 0, the second byte corresponds to sector 1, and so on with the last byte of data
corresponding to sector 15.
After the last data byte has been clocked in, the CS pin must be deasserted to initiate the internally self-timed
program cycle. The programming of the Sector Protection Register should take place in a time of tP, during which
time the Status Register will indicate that the device is busy. If the device is powered-down during the program
cycle, then the contents of the Sector Protection Register cannot be guaranteed.
If the proper number of data bytes is not clocked in before the CS pin is deasserted, then the protection status of
the sectors corresponding to the bytes not clocked in can not be guaranteed. For example, if only the first two bytes
are clocked in instead of the complete 16-bytes, then the protection status of the last 14 sectors cannot be
14
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
guaranteed. Furthermore, if more than 16-bytes of data is clocked into the device, then the data will wrap back
around to the beginning of the register. For instance, if 17-bytes of data are clocked in, then the 17th byte will be
stored at byte location 0 of the Sector Protection Register.
If a value other than 00H or FFH is clocked into a byte location of the Sector Protection Register, then the
protection status of the sector corresponding to that byte location cannot be guaranteed. For example, if a value of
17H is clocked into byte location 2 of the Sector Protection Register, then the protection status of sector 2 cannot
be guaranteed.
The Sector Protection Register can be reprogrammed while the sector protection enabled or disabled. Being able
to reprogram the Sector Protection Register with the sector protection enabled allows the user to temporarily
disable the sector protection to an individual sector rather than disabling sector protection completely.
The Program Sector Protection Register command utilizes the internal SRAM buffer 1 for processing. Therefore,
the contents of the buffer 1 will be altered from its previous state when this command is issued.
Table 9-5.
Program Sector Protection Register Command
Command
Program Sector Protection Register
Figure 9-3.
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
7FH
FCH
Program Sector Protection Register
CS
Opcode
Byte 1
SI
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Data Byte
n
Data Byte
n+1
Data Byte
n + 15
Each transition
represents eight bits
9.1.3
Read Sector Protection Register Command
To read the Sector Protection Register, the CS pin must first be asserted. Once the CS pin has been asserted, an
opcode of 32H and three dummy bytes must be clocked in via the SI pin. After the last bit of the opcode and
dummy bytes have been clocked in, any additional clock pulses on the SCK pins will result in data for the content
of the Sector Protection Register being output on the SO pin. The first byte corresponds to sector 0 (0a, 0b), the
second byte corresponds to sector 1 and the last byte (byte 16) corresponds to sector 15. Once the last byte of the
Sector Protection Register has been clocked out, any additional clock pulses will result in undefined data being
output on the SO pin. The CS must be deasserted to terminate the Read Sector Protection Register operation and
put the output into a high-impedance state.
Table 9-6.
Read Sector Protection Register Command
Command
Read Sector Protection Register
Note:
Figure 9-4.
Byte 1
Byte 2
Byte 3
Byte 4
32H
xxH
xxH
xxH
xx = Dummy Byte
Read Sector Protection Register
CS
SI
Opcode
X
X
X
Data Byte
n
SO
Data Byte
n+1
Data Byte
n + 15
Each transition
represents eight bits
15
3500N–DFLASH–05/10
9.1.4
Various Aspects About the Sector Protection Register
The Sector Protection Register is subject to a limit of 10,000 erase/program cycles. Users are encouraged to
carefully evaluate the number of times the Sector Protection Register will be modified during the course of the
applications’ life cycle. If the application requires that the Sector Protection Register be modified more than the
specified limit of 10,000 cycles because the application needs to temporarily unprotect individual sectors (sector
protection remains enabled while the Sector Protection Register is reprogrammed), then the application will need
to limit this practice. Instead, a combination of temporarily unprotecting individual sectors along with disabling
sector protection completely will need to be implemented by the application to ensure that the limit of 10,000 cycles
is not exceeded.
10.
Security Features
10.1
Sector Lockdown
The device incorporates a Sector Lockdown mechanism that allows each individual sector to be permanently
locked so that it becomes read only. This is useful for applications that require the ability to permanently protect a
number of sectors against malicious attempts at altering program code or security information. Once a sector is
locked down, it can never be erased or programmed, and it can never be unlocked.
To issue the Sector Lockdown command, the CS pin must first be asserted as it would be for any other command.
Once the CS pin has been asserted, the appropriate 4-byte opcode sequence must be clocked into the device in
the correct order. The 4-byte opcode sequence must start with 3DH and be followed by 2AH, 7FH, and 30H. After
the last byte of the command sequence has been clocked in, then three address bytes specifying any address
within the sector to be locked down must be clocked into the device. After the last address bit has been clocked in,
the CS pin must then be deasserted to initiate the internally self-timed lockdown sequence.
The lockdown sequence should take place in a maximum time of tP, during which time the Status Register will
indicate that the device is busy. If the device is powered-down before the completion of the lockdown sequence,
then the lockdown status of the sector cannot be guaranteed. In this case, it is recommended that the user read the
Sector Lockdown Register to determine the status of the appropriate sector lockdown bits or bytes and reissue the
Sector Lockdown command if necessary.
Table 10-1.
Sector Lockdown
Command
Sector Lockdown
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
7FH
30H
Figure 10-1. Sector Lockdown
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Address
Bytes
Address
Bytes
Address
Bytes
Each transition
represents eight bits
16
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
10.1.1 Sector Lockdown Register
Sector Lockdown Register is a nonvolatile register that contains 16-bytes of data, as shown below:
Table 10-2.
Sector Lockdown Register
Sector Number
0 (0a, 0b)
1 to 15
Locked
FFH
See Below
Unlocked
00H
Table 10-3.
Sector 0 (0a, 0b)
0a
0b
(Page 0-7)
(Page 8-255)
Bit 7, 6
Bit 5, 4
Bit 3, 2
Bit 1, 0
Data
Value
Sectors 0a, 0b Unlocked
00
00
00
00
00H
Sector 0a Locked (Page 0-7)
11
00
00
00
C0H
Sector 0b Locked (Page 8-255)
00
11
00
00
30H
Sectors 0a, 0b Locked (Page 0-255)
11
11
00
00
F0H
10.1.2 Reading the Sector Lockdown Register
The Sector Lockdown Register can be read to determine which sectors in the memory array are permanently
locked down. To read the Sector Lockdown Register, the CS pin must first be asserted. Once the CS pin has been
asserted, an opcode of 35H and three dummy bytes must be clocked into the device via the SI pin. After the last bit
of the opcode and dummy bytes have been clocked in, the data for the contents of the Sector Lockdown Register
will be clocked out on the SO pin. The first byte corresponds to sector 0 (0a, 0b) the second byte corresponds to
sector 1 and the las byte (byte 16) corresponds to sector 15. After the last byte of the Sector Lockdown Register
has been read, additional pulses on the SCK pin will simply result in undefined data being output on the SO pin.
Deasserting the CS pin will terminate the Read Sector Lockdown Register operation and put the SO pin into a
high-impedance state.
Table 10-4 details the values read from the Sector Lockdown Register.
Table 10-4.
Sector Lockdown Register
Command
Read Sector Lockdown Register
Note:
Byte 1
Byte 2
Byte 3
Byte 4
35H
xxH
xxH
xxH
xx = Dummy Byte
Figure 10-2. Read Sector Lockdown Register
CS
SI
Opcode
X
X
X
Data Byte
n
SO
Data Byte
n+1
Data Byte
n + 15
Each transition
represents eight bits
17
3500N–DFLASH–05/10
10.2
Security Register
The device contains a specialized Security Register that can be used for purposes such as unique device
serialization or locked key storage. The register is comprised of a total of 128-bytes that is divided into two
portions. The first 64-bytes (byte locations 0 through 63) of the Security Register are allocated as a one-time user
programmable space. Once these 64-bytes have been programmed, they cannot be reprogrammed. The
remaining 64-bytes of the register (byte locations 64 through 127) are factory programmed by Atmel® and will
contain a unique value for each device. The factory programmed data is fixed and cannot be changed.
Table 10-5.
Security Register
Security Register Byte Number
0
Data Type
1
···
62
63
One-time User Programmable
64
65
···
126
127
Factory Programmed By Atmel
10.2.1 Programming the Security Register
The user programmable portion of the Security Register does not need to be erased before it is programmed.
To program the Security Register, the CS pin must first be asserted and the appropriate 4-byte opcode sequence
must be clocked into the device in the correct order. The 4-byte opcode sequence must start with 9BH and be
followed by 00H, 00H, and 00H. After the last bit of the opcode sequence has been clocked into the device, the
data for the contents of the 64-byte user programmable portion of the Security Register must be clocked in.
After the last data byte has been clocked in, the CS pin must be deasserted to initiate the internally self-timed
program cycle. The programming of the Security Register should take place in a time of tP, during which time the
Status Register will indicate that the device is busy. If the device is powered-down during the program cycle, then
the contents of the 64-byte user programmable portion of the Security Register cannot be guaranteed.
If the full 64-bytes of data is not clocked in before the CS pin is deasserted, then the values of the byte locations
not clocked in cannot be guaranteed. For example, if only the first two bytes are clocked in instead of the complete
64-bytes, then the remaining 62-bytes of the user programmable portion of the Security Register cannot be
guaranteed. Furthermore, if more than 64-bytes of data is clocked into the device, then the data will wrap back
around to the beginning of the register. For instance, if 65-bytes of data are clocked in, then the 65th byte will be
stored at byte location 0 of the Security Register.
The user programmable portion of the Security Register can only be programmed one time. Therefore, it is
not possible to only program the first two bytes of the register and then program the remaining 62-bytes at a later
time.
The Program Security Register command utilizes the internal SRAM buffer 1 for processing. Therefore, the
contents of the buffer 1 will be altered from its previous state when this command is issued.
Figure 10-3. Program Security Register
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Data Byte
n
Data Byte
n+1
Data Byte
n+x
Each transition
represents eight bits
18
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
10.2.2 Reading the Security Register
The Security Register can be read by first asserting the CS pin and then clocking in an opcode of 77H followed by
three dummy bytes. After the last don't care bit has been clocked in, the content of the Security Register can be
clocked out on the SO pins. After the last byte of the Security Register has been read, additional pulses on the
SCK pin will simply result in undefined data being output on the SO pins.
Deasserting the CS pin will terminate the Read Security Register operation and put the SO pins into a highimpedance state.
Figure 10-4. Read Security Register
CS
SI
Opcode
X
X
X
Data Byte
n
SO
Data Byte
n+1
Data Byte
n+x
Each transition
represents eight bits
11.
Additional Commands
11.1
Main Memory Page to Buffer Transfer
A page of data can be transferred from the main memory to either buffer 1 or buffer 2. To start the operation for the
standard Atmel® DataFlash® page size (528-bytes), a 1-byte opcode, 53H for buffer 1 and 55H for buffer 2, must
be clocked into the device, followed by three address bytes comprised of two don’t care bits, 12 page address bits
(PA11 - PA0), which specify the page in main memory that is to be transferred, and 10 don’t care bits. To perform
a main memory page to buffer transfer for the binary page size (512-bytes), the opcode 53H for buffer 1 or 55H for
buffer 2, must be clocked into the device followed by three address bytes consisting of three don’t care bits, 12
page address bits (A20 - A9) which specify the page in the main memory that is to be transferred, and nine don’t
care bits. The CS pin must be low while toggling the SCK pin to load the opcode and the address bytes from the
input pin (SI). The transfer of the page of data from the main memory to the buffer will begin when the CS pin
transitions from a low to a high state. During the transfer of a page of data (tXFR), the status register can be read or
the RDY/BUSY can be monitored to determine whether the transfer has been completed.
11.2
Main Memory Page to Buffer Compare
A page of data in main memory can be compared to the data in buffer 1 or buffer 2. To initiate the operation for
standard DataFlash page size, a 1-byte opcode, 60H for buffer 1 and 61H for buffer 2, must be clocked into the
device, followed by three address bytes consisting of two don’t care bits, 12 page address bits (PA11 - PA0) that
specify the page in the main memory that is to be compared to the buffer, and 10 don’t care bits. To start a main
memory page to buffer compare for a binary page size, the opcode 60H for buffer 1 or 61H for buffer 2, must be
clocked into the device followed by three address bytes consisting of three don’t care bits, 12 page address bits
(A20 - A9) that specify the page in the main memory that is to be compared to the buffer, and nine don’t care bits.
The CS pin must be low while toggling the SCK pin to load the opcode and the address bytes from the input pin
(SI). On the low-to-high transition of the CS pin, the data bytes in the selected main memory page will be compared
with the data bytes in buffer 1 or buffer 2. During this time (tCOMP), the status register and the RDY/BUSY pin will
indicate that the part is busy. On completion of the compare operation, bit six of the status register is updated with
the result of the compare.
19
3500N–DFLASH–05/10
11.3
Auto Page Rewrite
This mode is only needed if multiple bytes within a page or multiple pages of data are modified in a random fashion
within a sector. This mode is a combination of two operations: Main Memory Page to Buffer Transfer and Buffer to
Main Memory Page Program with Built-in Erase. A page of data is first transferred from the main memory to buffer
1 or buffer 2, and then the same data (from buffer 1 or buffer 2) is programmed back into its original page of main
memory. To start the rewrite operation for standard Atmel® DataFlash® page size (528-bytes), a 1-byte opcode,
58H for buffer 1 or 59H for buffer 2, must be clocked into the device, followed by three address bytes comprised of
two don’t care bits, 12 page address bits (PA11-PA0) that specify the page in main memory to be rewritten and 10
don’t care bits. To initiate an auto page rewrite for a binary page size (512-bytes), the opcode 58H for buffer 1 or
59H for buffer 2, must be clocked into the device followed by three address bytes consisting of three don’t care bits,
12 page address bits (A20 - A9) that specify the page in the main memory that is to be written and nine don’t care
bits. When a low-to-high transition occurs on the CS pin, the part will first transfer data from the page in main
memory to a buffer and then program the data from the buffer back into same page of main memory. The operation
is internally self-timed and should take place in a maximum time of tEP. During this time, the status register and the
RDY/BUSY pin will indicate that the part is busy.
If a sector is programmed or reprogrammed sequentially page by page, then the programming algorithm shown in
Figure 25-1 (page 45) is recommended. Otherwise, if multiple bytes in a page or several pages are programmed
randomly in a sector, then the programming algorithm shown in Figure 25-2 (page 46) is recommended. Each
page within a sector must be updated/rewritten at least once within every 20,000 cumulative page erase/program
operations in that sector. Please contact Atmel for availability of devices that are specified to exceed the 20K cycle
cumulative limit.
11.4
Status Register Read
The status register can be used to determine the device’s ready/busy status, page size, a Main Memory Page to
Buffer Compare operation result, the Sector Protection status or the device density. The Status Register can be
read at any time, including during an internally self-timed program or erase operation. To read the status register,
the CS pin must be asserted and the opcode of D7H must be loaded into the device. After the opcode is clocked in,
the 1-byte status register will be clocked out on the output pin (SO), starting with the next clock cycle. The data in
the status register, starting with the MSB (bit seven), will be clocked out on the SO pin during the next eight clock
cycles. After the one byte of the status register has been clocked out, the sequence will repeat itself (as long as CS
remains low and SCK is being toggled). The data in the status register is constantly updated, so each repeating
sequence will output new data.
Ready/busy status is indicated using bit seven of the status register. If bit seven is a one, then the device is not
busy and is ready to accept the next command. If bit seven is a zero, then the device is in a busy state. Since the
data in the status register is constantly updated, the user must toggle SCK pin to check the ready/busy status.
There are several operations that can cause the device to be in a busy state: Main Memory Page to Buffer
Transfer, Main Memory Page to Buffer Compare, Buffer to Main Memory Page Program, Main Memory Page
Program through Buffer, Page Erase, Block Erase, Sector Erase, Chip Erase and Auto Page Rewrite.
The result of the most recent Main Memory Page to Buffer Compare operation is indicated using bit 6 of the status
register. If bit six is a zero, then the data in the main memory page matches the data in the buffer. If bit six is a one,
then at least one bit of the data in the main memory page does not match the data in the buffer.
Bit one in the Status Register is used to provide information to the user whether or not the sector protection has
been enabled or disabled, either by software-controlled method or hardware-controlled method. A logic 1 indicates
that sector protection has been enabled and logic 0 indicates that sector protection has been disabled.
Bit zero in the Status Register indicates whether the page size of the main memory array is configured for “power
of 2” binary page size (512-bytes) or standard DataFlash page size (528-bytes). If bit zero is a one, then the page
size is set to 512-bytes. If bit zero is a zero, then the page size is set to 528-bytes.
20
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
The device density is indicated using bits five, four, three, and two of the status register. For the Atmel ®
AT45DB161D, the four bits are 1011 The decimal value of these four binary bits does not equate to the device
density; the four bits represent a combinational code relating to differing densities of Atmel DataFlash devices. The
device density is not the same as the density code indicated in the JEDEC device ID information. The device
density is provided only for backward compatibility.
Table 11-1.
12.
Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RDY/BUSY
COMP
1
0
1
1
PROTECT
PAGE SIZE
Deep Power-down
After initial power-up, the device will default in standby mode. The Deep Power-down command allows the device
to enter into the lowest power consumption mode. To enter the Deep Power-down mode, the CS pin must first be
asserted. Once the CS pin has been asserted, an opcode of B9H command must be clocked in via input pin (SI).
After the last bit of the command has been clocked in, the CS pin must be de-asserted to initiate the Deep Powerdown operation. After the CS pin is de-asserted, the will device enter the Deep Power-down mode within the
maximum tEDPD time. Once the device has entered the Deep Power-down mode, all instructions are ignored except
for the Resume from Deep Power-down command.
Table 12-1.
Deep Power-down
Command
Opcode
Deep Power-down
B9H
Figure 12-1. Deep Power-down
CS
SI
Opcode
Each transition
represents eight bits
12.1
Resume from Deep Power-down
The Resume from Deep Power-down command takes the device out of the Deep Power-down mode and returns it
to the normal standby mode. To Resume from Deep Power-down mode, the CS pin must first be asserted and an
opcode of ABH command must be clocked in via input pin (SI). After the last bit of the command has been clocked
in, the CS pin must be de-asserted to terminate the Deep Power-down mode. After the CS pin is de-asserted, the
device will return to the normal standby mode within the maximum tRDPD time. The CS pin must remain high during
the tRDPD time before the device can receive any commands. After resuming form Deep Power-down, the device
will return to the normal standby mode.
Table 12-2.
Resume from Deep Power-down
Command
Resume from Deep Power-down
Opcode
ABH
21
3500N–DFLASH–05/10
Figure 12-2. Resume from Deep Power-Down
CS
SI
Opcode
Each transition
represents eight bits
13.
“Power of 2” Binary Page Size Option
“Power of 2” binary page size Configuration Register is a user-programmable nonvolatile register that allows the
page size of the main memory to be configured for binary page size (512-bytes) or standard Atmel® DataFlash
page size (528-bytes). The “power of 2” page size is a one-time programmable configuration register and
once the device is configured for “power of 2” page size, it cannot be reconfigured again. The devices are
initially shipped with the page size set to 528-bytes. The user has the option of ordering binary page size (512
bytes) devices from the factory. For details, please refer to Section 26. “Ordering Information” on page 47.
For the binary “power of 2” page size to become effective, the following steps must be followed:
1. Program the one-time programmable configuration resister using opcode sequence 3DH, 2AH, 80H and
A6H (please see Section 13.1).
2. Power cycle the device (i.e. power down and power up again).
3. User can now program the page for the binary page size.
If the above steps are not followed in setting the the page size prior to page programming, user may expect
incorrect data during a read operation.
13.1
Programming the Configuration Register
To program the Configuration Register for “power of 2” binary page size, the CS pin must first be asserted as it
would be with any other command. Once the CS pin has been asserted, the appropriate 4-byte opcode sequence
must be clocked into the device in the correct order. The 4-byte opcode sequence must start with 3DH and be
followed by 2AH, 80H, and A6H. After the last bit of the opcode sequence has been clocked in, the CS pin must be
deasserted to initiate the internally self-timed program cycle. The programming of the Configuration Register
should take place in a time of tP, during which time the Status Register will indicate that the device is busy. The
device must be power cycled after the completion of the program cycle to set the “power of 2” page size. If the
device is powered-down before the completion of the program cycle, then setting the Configuration Register
cannot be guaranteed. However, the user should check bit zero of the status register to see whether the page size
was configured for binary page size. If not, the command can be re-issued again.
Table 13-1.
Programming the Configuration Register
Command
Power of Two Page Size
Byte 1
Byte 2
Byte 3
Byte 4
3DH
2AH
80H
A6H
Figure 13-1. Erase Sector Protection Register
CS
SI
Opcode
Byte 1
Opcode
Byte 2
Opcode
Byte 3
Opcode
Byte 4
Each transition
represents eight bits
22
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
14.
Manufacturer and Device ID Read
Identification information can be read from the device to enable systems to electronically query and identify the
device while it is in system. The identification method and the command opcode comply with the JEDEC standard
for “Manufacturer and Device ID Read Methodology for SPI Compatible Serial Interface Memory Devices”. The
type of information that can be read from the device includes the JEDEC defined Manufacturer ID, the vendor
specific Device ID, and the vendor specific Extended Device Information.
To read the identification information, the CS pin must first be asserted and the opcode of 9FH must be clocked
into the device. After the opcode has been clocked in, the device will begin outputting the identification data on the
SO pin during the subsequent clock cycles. The first byte that will be output will be the Manufacturer ID followed by
two bytes of Device ID information. The fourth byte output will be the Extended Device Information String Length,
which will be 00H indicating that no Extended Device Information follows. As indicated in the JEDEC standard,
reading the Extended Device Information String Length and any subsequent data is optional.
Deasserting the CS pin will terminate the Manufacturer and Device ID Read operation and put the SO pin into a
high-impedance state. The CS pin can be deasserted at any time and does not require that a full byte of data be
read.
14.1
Manufacturer and Device ID Information
JEDEC Assigned Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1FH
0
0
0
1
1
1
1
1
Family Code
Manufacturer ID
1FH = Atmel
Density Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Family Code
26H
0
0
1
0
0
1
1
0
Density Code
MLC Code
001 = Atmel DataFlash
00110 = 16-Mbit
Product Version Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00H
0
0
0
0
0
0
0
0
MLC Code
000 = 1-bit/Cell Technology
Product Version
00000 = Initial Version
Byte Count
00H = 0 Bytes of Information
Byte Count
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00H
0
0
0
0
0
0
0
0
CS
SI
9FH
Opcode
SO
Each transition
represents 8 bits
Note:
1FH
26H
00H
00H
Data
Data
Manufacturer ID
Byte 1
Device ID
Byte 2
Device ID
Byte 3
Extended
Device
Information
String Length
Extended
Device
Information
Byte x
Extended
Device
Information
Byte x + 1
This information would only be output
if the Extended Device Information String Length
value was something other than 00H.
Based on JEDEC publication 106 (JEP106), Manufacturer ID data can be comprised of any number of bytes. Some manufacturers
may have Manufacturer ID codes that are two, three or even four bytes long with the first byte(s) in the sequence being 7FH. A system
should detect code 7FH as a “Continuation Code” and continue to read Manufacturer ID bytes. The first non-7FH byte would signify
the last byte of Manufacturer ID data. For Atmel (and some other manufacturers), the Manufacturer ID data is comprised of only one
byte.
23
3500N–DFLASH–05/10
14.2
Operation Mode Summary
The commands described previously can be grouped into four different categories to better describe which
commands can be executed at what times.
Group A commands consist of:
1.
2.
3.
4.
5.
Main Memory Page Read
Continuous Array Read
Read Sector Protection Register
Read Sector Lockdown Register
Read Security Register
Group B commands consist of:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Page Erase
Block Erase
Sector Erase
Chip Erase
Main Memory Page to Buffer 1 (or 2) Transfer
Main Memory Page to Buffer 1 (or 2) Compare
Buffer 1 (or 2) to Main Memory Page Program with Built-in Erase
Buffer 1 (or 2) to Main Memory Page Program without Built-in Erase
Main Memory Page Program through Buffer 1 (or 2)
Auto Page Rewrite
Group C commands consist of:
1.
2.
3.
4.
Buffer 1 (or 2) Read
Buffer 1 (or 2) Write
Status Register Read
Manufacturer and Device ID Read
Group D commands consist of:
1.
2.
3.
4.
Erase Sector Protection Register
Program Sector Protection Register
Sector Lockdown
Program Security Register
If a Group A command is in progress (not fully completed), then another command in Group A, B, C, or D should
not be started. However, during the internally self-timed portion of Group B commands, any command in Group C
can be executed. The Group B commands using buffer 1 should use Group C commands using buffer 2 and vice
versa. Finally, during the internally self-timed portion of a Group D command, only the Status Register Read
command should be executed.
24
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
15.
Command Tables
Table 15-1.
Read Commands
Command
Opcode
Main Memory Page Read
D2H
Continuous Array Read (Legacy Command)
E8H
Continuous Array Read (Low Frequency)
03H
Continuous Array Read (High Frequency)
0BH
Buffer 1 Read (Low Frequency)
D1H
Buffer 2 Read (Low Frequency)
D3H
Buffer 1 Read
D4H
Buffer 2 Read
D6H
Table 15-2.
Program and Erase Commands
Command
Opcode
Buffer 1 Write
84H
Buffer 2 Write
87H
Buffer 1 to Main Memory Page Program with Built-in Erase
83H
Buffer 2 to Main Memory Page Program with Built-in Erase
86H
Buffer 1 to Main Memory Page Program without Built-in Erase
88H
Buffer 2 to Main Memory Page Program without Built-in Erase
89H
Page Erase
81H
Block Erase
50H
Sector Erase
7CH
Chip Erase
C7H, 94H, 80H, 9AH
Main Memory Page Program Through Buffer 1
82H
Main Memory Page Program Through Buffer 2
85H
Table 15-3.
Protection and Security Commands
Command
Opcode
Enable Sector Protection
3DH + 2AH + 7FH + A9H
Disable Sector Protection
3DH + 2AH + 7FH + 9AH
Erase Sector Protection Register
3DH + 2AH + 7FH + CFH
Program Sector Protection Register
3DH + 2AH + 7FH + FCH
Read Sector Protection Register
Sector Lockdown
Read Sector Lockdown Register
Program Security Register
Read Security Register
32H
3DH + 2AH + 7FH + 30H
35H
9BH + 00H + 00H + 00H
77H
25
3500N–DFLASH–05/10
Table 15-4.
Additional Commands
Command
Opcode
Main Memory Page to Buffer 1 Transfer
53H
Main Memory Page to Buffer 2 Transfer
55H
Main Memory Page to Buffer 1 Compare
60H
Main Memory Page to Buffer 2 Compare
61H
Auto Page Rewrite through Buffer 1
58H
Auto Page Rewrite through Buffer 2
59H
Deep Power-down
B9H
Resume from Deep Power-down
ABH
Status Register Read
D7H
Manufacturer and Device ID Read
9FH
Table 15-5.
Legacy Commands(1)
Command
Opcode
Buffer 1 Read
54H
Buffer 2 Read
56H
Main Memory Page Read
52H
Continuous Array Read
68H
Status Register Read(2)
57H
Notes:
1. These legacy commands are not recommended for new designs
2. Refer to the Revision History table on page 52
26
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
Table 15-6.
Detailed Bit-level Addressing Sequence for Binary Page Size (512-Bytes)
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Address Byte
Reserved
Address Byte
Reserved
Address Byte
Reserved
Page Size = 512-bytes
03h
0
0
0
0
0
0
1
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
N/A
0Bh
0
0
0
0
1
0
1
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
1
50h
0
1
0
1
0
0
0
0
x
x
x
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
x
x
x
N/A
53h
0
1
0
1
0
0
1
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
55h
0
1
0
1
0
1
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
58h
0
1
0
1
1
0
0
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
59h
0
1
0
1
1
0
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
60h
0
1
1
0
0
0
0
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
61h
0
1
1
0
0
0
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
77h
0
1
1
1
0
1
1
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
N/A
7Ch
0
1
1
1
1
1
0
0
x
x
x
A
A
A
A
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
N/A
81h
1
0
0
0
0
0
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
X
x
x
x
x
x
x
x
x
N/A
82h
1
0
0
0
0
0
1
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
N/A
83h
1
0
0
0
0
0
1
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
X
x
x
x
x
x
x
x
x
N/A
84h
1
0
0
0
0
1
0
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
N/A
85h
1
0
0
0
0
1
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
N/A
86h
1
0
0
0
0
1
1
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
87h
1
0
0
0
0
1
1
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
N/A
88h
1
0
0
0
1
0
0
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
89h
1
0
0
0
1
0
0
1
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
x
x
x
x
x
x
x
x
x
N/A
9Fh
1
0
0
1
1
1
1
1
N/A
N/A
N/A
N/A
B9h
1
0
1
1
1
0
0
1
N/A
N/A
N/A
N/A
ABh
1
0
1
0
1
0
1
1
N/A
N/A
N/A
N/A
D1h
1
1
0
1
0
0
0
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
N/A
D2h
1
1
0
1
0
0
1
0
x
x
x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
4
D3h
1
1
0
1
0
0
1
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
N/A
D4h
1
1
0
1
0
1
0
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
1
D6h
1
1
0
1
0
1
1
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
A
A
A
A
A
A
A
A
A
1
D7h
1
1
0
1
0
1
1
1
1
1
1
0
1
0
0
0
Opco
de
E8h
Notes:
Opcode
N/A
x
x
N/A
x
A
A
A
A
A
A
A
N/A
A
A
A
A
A
A
A
A
Additional
Don’t Care
Bytes
N/A
A
A
A
A
A
A
4
x = Don’t Care
27
3500N–DFLASH–05/10
Table 15-7.
Detailed Bit-level Addressing Sequence for Standard Atmel DataFlash Page Size (528-Bytes)
BA0
0
0
1
0
1
1
x
x
P P P P P P
P P P P P P B B
B B B B B B B
B
1
50h
0
1
0
1
0
0
0
0
x
x
P P P P P P
P P P x
x
x
x
x
x
x
x
x
x
x
N/A
53h
0
1
0
1
0
0
1
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
55h
0
1
0
1
0
1
0
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
58h
0
1
0
1
1
0
0
0
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
59h
0
1
0
1
1
0
0
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
60h
0
1
1
0
0
0
0
0
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
61h
0
1
1
0
0
0
0
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
77h
0
1
1
1
0
1
1
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
N/A
7Ch
0
1
1
1
1
1
0
0
x
x
P P P P x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
N/A
81h
1
0
0
0
0
0
0
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
82h
1
0
0
0
0
0
1
0
x
x
P P P P P P
P P P P P P B B
B B B B B B B
B
N/A
83h
1
0
0
0
0
0
1
1
x
x
P P P P P P
P P P P P P x
x
x
x
N/A
84h
1
0
0
0
0
1
0
0
x
x
x
x
B B
B B B B B B B
B
N/A
85h
1
0
0
0
0
1
0
1
x
x
P P P P P P
P P P P P P B B
B B B B B B B
B
N/A
86h
1
0
0
0
0
1
1
0
x
x
P P P P P P
P P P P P P x
x
x
x
N/A
87h
1
0
0
0
0
1
1
1
x
x
x
x
B B B B B B B
B
N/A
88h
1
0
0
0
1
0
0
0
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
89h
1
0
0
0
1
0
0
1
x
x
P P P P P P
P P P P P P x
x
x
x
x
x
x
x
x
x
N/A
9Fh
1
0
0
1
1
1
1
1
N/A
N/A
N/A
N/A
B9h
1
0
1
1
1
0
0
1
N/A
N/A
N/A
N/A
ABh
1
0
1
0
1
0
1
1
N/A
N/A
N/A
N/A
D1h
1
1
0
1
0
0
0
1
x
x
x
D2h
1
1
0
1
0
0
1
0
x
x
D3h
1
1
0
1
0
0
0
1
x
D4h
1
1
0
1
0
1
0
0
D6h
1
1
0
1
0
1
1
0
D7h
1
1
0
1
0
1
1
1
1
1
1
0
1
0
0
E8h
Notes:
P = Page Address Bit
0
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
B B
x
x
x
x
x
x
x
x
x
x
B
N/A
P P P P P P
P P P P P P B B
B B B B B B B
B
4
x
x
x
x
x
x
x
x
x
x
x
x
x
B B
B B B B B B B
B
N/A
x
x
x
x
x
x
x
x
x
x
x
x
x
x
B B
B B B B B B B
B
1
x
x
x
x
x
x
x
x
x
x
x
x
x
x
B B
B B B B B B B
B
1
x
x
x
x
B B B B B B B
x
x
x
x
B B
N/A
x
x
x
BA1
0
BA2
0
BA3
0Bh
BA4
N/A
BA5
B
BA6
B B B B B B B
BA7
P P P P P P B B
BA8
P P P P P P
BA9
x
PA0
x
PA1
1
PA2
1
PA3
0
PA4
0
PA5
0
PA6
0
PA7
0
PA8
0
PA9
03h
Opcode
PA10
PA11
Address Byte
Reserved
Address Byte
Additional
Don’t Care
Bytes
Opcode
28
Address Byte
Reserved
Page Size = 528-bytes
N/A
P P P P P P
B = Byte/Buffer Address Bit
P P P P P P B B
N/A
B B B B B B B
N/A
B
4
x = Don’t Care
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
16.
Power-on/Reset State
When power is first applied to the device, or when recovering from a reset condition, the device will default to Mode
3. In addition, the output pin (SO) will be in a high impedance state, and a high-to-low transition on the CS pin will
be required to start a valid instruction. The mode (Mode 3 or Mode 0) will be automatically selected on every falling
edge of CS by sampling the inactive clock state.
16.1
Initial Power-up/Reset Timing Restrictions
At power up, the device must not be selected until the supply voltage reaches the VCC (min.) and further delay of
tVCSL. During power-up, the internal Power-on Reset circuitry keeps the device in reset mode until the VCC rises
above the Power-on Reset threshold value (VPOR). At this time, all operations are disabled and the device does not
respond to any commands. After power up is applied and the VCC is at the minimum operating voltage VCC (min.),
the tVCSL delay is required before the device can be selected in order to perform a read operation.
Similarly, the tPUW delay is required after the VCC rises above the Power-on Reset threshold value (VPOR) before the
device can perform a write (Program or Erase) operation. After initial power-up, the device will default in Standby
mode.
Table 16-1.
17.
Initial Power-up/Reset Timing Restrictions
Symbol
Parameter
tVCSL
VCC (min.) to Chip Select low
tPUW
Power-Up Device Delay before Write Allowed
VPOR
Power-ON Reset Voltage
Min
Typ
Max
70
1.5
Units
µs
20
ms
2.5
V
System Considerations
The Atmel® RapidS serial interface is controlled by the clock SCK, serial input SI and chip select CS pins. These
signals must rise and fall monotonically and be free from noise. Excessive noise or ringing on these pins can be
misinterpreted as multiple edges and cause improper operation of the device. The PC board traces must be kept to
a minimum distance or appropriately terminated to ensure proper operation. If necessary, decoupling capacitors
can be added on these pins to provide filtering against noise glitches.
As system complexity continues to increase, voltage regulation is becoming more important. A key element of any
voltage regulation scheme is its current sourcing capability. Like all Flash memories, the peak current for Atmel
DataFlash® occur during the programming and erase operation. The regulator needs to supply this peak current
requirement. An under specified regulator can cause current starvation. Besides increasing system noise, current
starvation during programming or erase can lead to improper operation and possible data corruption.
29
3500N–DFLASH–05/10
18.
Electrical Specifications
Table 18-1.
Absolute Maximum Ratings*
*NOTICE:
Temperature under Bias ................. -55°C to +125°C
Storage Temperature...................... -65°C to +150°C
All Input Voltages (except VCC but including NC pins)
with Respect to Ground ....................-0.6V to +6.25V
All Output Voltages
with Respect to Ground ..............-0.6V to VCC + 0.6V
Table 18-2.
DC and AC Operating Range
Operating Temperature (Case)
Atmel AT45DB161D (2.5V Version)
Atmel AT45DB161D
-40C to 85C
-40C to 85C
2.5V to 3.6V
2.7V to 3.6V
Ind.
VCC Power Supply
Table 18-3.
DC Characteristics
Symbol
Parameter
Condition
IDP
Deep Power-down Current
ISB
Standby Current
(1)
ICC1
Stresses beyond those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
The "Absolute Maximum Ratings" are stress ratings only
and functional operation of the device at these or any
other conditions beyond those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods
may affect device reliability. Voltage Extremes referenced
in the "Absolute Maximum Ratings" are intended to
accommodate short duration undershoot/overshoot conditions and does not imply or guarantee functional device
operation at these levels for any extended period of time
Active Current, Read Operation
Min
Typ
Max
Units
CS, RESET, WP = VIH, all
inputs at CMOS levels
15
25
µA
CS, RESET, WP = VIH, all
inputs at CMOS levels
25
50
µA
f = 20MHz; IOUT = 0mA;
VCC = 3.6V
7
10
mA
f = 33MHz; IOUT = 0mA;
VCC = 3.6V
8
12
mA
f = 50MHz; IOUT = 0mA;
VCC = 3.6V
10
14
mA
f = 66MHz; IOUT = 0mA;
VCC = 3.6V
11
15
mA
12
17
mA
ICC2
Active Current, Program/Erase
Operation
VCC = 3.6V
ILI
Input Load Current
VIN = CMOS levels
1
µA
ILO
Output Leakage Current
VI/O = CMOS levels
1
µA
VIL
Input Low Voltage
VCC x 0.3
V
VIH
Input High Voltage
VOL
Output Low Voltage
IOL = 1.6mA; VCC = 2.7V
VOH
Output High Voltage
IOH = -100µA
Notes:
VCC x 0.7
V
0.4
VCC - 0.2V
V
V
1. ICC1 during a buffer read is 20mA maximum @ 20MHz
2. All inputs (SI, SCK, CS#, WP#, and RESET#) are guaranteed by design to be 5V tolerant
30
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
Table 18-4.
AC Characteristics – Atmel RapidS/Serial Interface
Atmel AT45DB161D
(2.5V Version)
Symbol
Parameter
fSCK
SCK Frequency
fCAR1
Min
Typ
Max
Atmel AT45DB161D
Min
Typ
Max
Units
50
66
MHz
SCK Frequency for Continuous Array Read
50
66
MHz
fCAR2
SCK Frequency for Continuous Array Read
(Low Frequency)
33
33
MHz
tWH
SCK High Time
6.8
6.8
ns
tWL
SCK Low Time
6.8
6.8
ns
tSCKR(1)
SCK Rise Time, Peak-to-Peak (Slew Rate)
0.1
0.1
V/ns
tSCKF(1)
SCK Fall Time, Peak-to-Peak (Slew Rate)
0.1
0.1
V/ns
tCS
Minimum CS High Time
50
50
ns
tCSS
CS Setup Time
5
5
ns
tCSH
CS Hold Time
5
5
ns
tCSB
CS High to RDY/BUSY Low
tSU
Data In Setup Time
2
2
ns
tH
Data In Hold Time
3
3
ns
tHO
Output Hold Time
0
0
ns
tDIS
Output Disable Time
tV
Output Valid
tWPE
100
35
ns
8
6
ns
WP Low to Protection Enabled
1
1
µs
tWPD
WP High to Protection Disabled
1
1
µs
tEDPD
CS High to Deep Power-down Mode
3
3
µs
tRDPD
CS High to Standby Mode
35
35
µs
tXFR
Page to Buffer Transfer Time
200
200
µs
tCOMP
Page to Buffer Compare Time
200
200
µs
tEP
Page Erase and Programming Time
(512-/528-bytes)
17
40
17
40
ms
tP
Page Programming Time (512-/528-bytes)
3
6
3
6
ms
tPE
Page Erase Time (512-/528-bytes)
15
35
15
35
ms
tBE
Block Erase Time (4096-/4224-bytes)
45
100
45
100
ms
tSE
Sector Erase Time (131,072/135,168-bytes)
0.7
1.3
0.7
1.3
s
tCE
Chip Erase Time
12
25
12
25
s
tRST
RESET Pulse Width
tREC
RESET Recovery Time
10
27
ns
35
Note:
27
100
10
1
µs
1
µs
1. Values are based on device characterization, not 100% tested in production
31
3500N–DFLASH–05/10
19.
Input Test Waveforms and Measurement Levels
AC
DRIVING
LEVELS
2.4V
AC
MEASUREMENT
LEVEL
1.5V
0.45V
tR, tF < 2ns (10% to 90%)
20.
Output Test Load
DEVICE
UNDER
TEST
30pF
21.
AC Waveforms
Six different timing waveforms are shown on page 36. Waveform 1 shows the SCK signal being low when CS
makes a high-to-low transition, and waveform 2 shows the SCK signal being high when CS makes a high-to-low
transition. In both cases, output SO becomes valid while the SCK signal is still low (SCK low time is specified as
tWL). Timing waveforms 1 and 2 conform to Atmel® RapidS serial interface but for frequencies up to 66MHz.
Waveforms 1 and 2 are compatible with SPI Mode 0 and SPI Mode 3, respectively.
Waveform 3 and waveform 4 illustrate general timing diagram for RapidS serial interface. These are similar to
waveform 1 and waveform 2, except that output SO is not restricted to become valid during the tWL period. These
timing waveforms are valid over the full frequency range (maximum frequency = 66MHz) of the RapidS serial case.
21.1
Waveform 1 – SPI Mode 0 Compatible (for frequencies up to 66MHz)
tCS
CS
tWH
tCSS
tWL
tCSH
SCK
tHO
tV
SO
HIGH IMPEDANCE
tSU
SI
32
VALID OUT
tDIS
HIGH IMPEDANCE
tH
VALID IN
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
21.2
Waveform 2 – SPI Mode 3 Compatible (for frequencies up to 66MHz)
tCS
CS
tCSS
tWL
tWH
tCSH
SCK
tV
SO
tHO
HIGH Z
VALID OUT
tSU
tH
VALID IN
SI
21.3
tDIS
HIGH IMPEDANCE
Waveform 3 – Atmel RapidS Mode 0 (FMAX = 66MHz)
tCS
CS
tWH
tCSS
tWL
tCSH
SCK
tHO
tV
SO
HIGH IMPEDANCE
VALID OUT
tSU
SI
21.4
tDIS
HIGH IMPEDANCE
tH
VALID IN
Waveform 4 – Atmel RapidS Mode 3 (FMAX = 66MHz)
tCS
CS
tCSS
tWL
tWH
tCSH
SCK
tV
SO
HIGH Z
tHO
VALID OUT
tSU
SI
21.5
tDIS
HIGH IMPEDANCE
tH
VALID IN
Utilizing the Atmel RapidS Function
To take advantage of the Atmel® RapidS™ function's ability to operate at higher clock frequencies, a full clock cycle
must be used to transmit data back and forth across the serial bus. The Atmel DataFlash® is designed to always
clock its data out on the falling edge of the SCK signal and clock data in on the rising edge of SCK.
For full clock cycle operation to be achieved, when the DataFlash is clocking data out on the falling edge of SCK,
the host controller should wait until the next falling edge of SCK to latch the data in. Similarly, the host controller
should clock its data out on the rising edge of SCK in order to give the DataFlash a full clock cycle to latch the
incoming data in on the next rising edge of SCK.
33
3500N–DFLASH–05/10
Figure 21-1. Atmel RapidS Mode
Slave CS
1
8
2
3
4
5
6
1
8
7
2
3
4
5
6
1
7
SCK
B
E
A
MOSI
C
D
MSB
LSB
BYTE-MOSI
H
G
I
F
MISO
MSB
LSB
BYTE-SO
MOSI = Master Out, Slave In
MISO = Master In, Slave Out
The Master is the host controller and the Slave is the Atmel DataFlash
The Master always clocks data out on the rising edge of SCK and always clocks data in on the falling edge of SCK.
The Slave always clocks data out on the falling edge of SCK and always clocks data in on the rising edge of SCK.
A.
B.
C.
D.
E.
F.
G.
H.
I.
21.6
Master clocks out first bit of BYTE-MOSI on the rising edge of SCK
Slave clocks in first bit of BYTE-MOSI on the next rising edge of SCK
Master clocks out second bit of BYTE-MOSI on the same rising edge of SCK
Last bit of BYTE-MOSI is clocked out from the Master
Last bit of BYTE-MOSI is clocked into the slave
Slave clocks out first bit of BYTE-SO
Master clocks in first bit of BYTE-SO
Slave clocks out second bit of BYTE-SO
Master clocks in last bit of BYTE-SO
Reset Timing
CS
tREC
tCSS
SCK
tRST
RESET
SO (OUTPUT)
HIGH IMPEDANCE
HIGH IMPEDANCE
SI (INPUT)
Note:
34
The CS signal should be in the high state before the RESET signal is deasserted
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
21.7
Command Sequence for Read/Write Operations for Page Size 512-Bytes (Except Status
Register Read, Manufacturer and Device ID Read)
SI (INPUT)
MSB
CMD
XXX
XXXX
Don’t Care
Bits
21.8
8-bits
8-bits
XXXXXXXXX
Page Address
(A20 - A9)
XXXX XXXX
LSB
Byte/Buffer Address
(A8 - A0/BFA8 - BFA0)
Command Sequence for Read/Write Operations for Page Size 528-Bytes (Except Status
Register Read, Manufacturer and Device ID Read)
CMD
SI (INPUT)
8-bits
8-bits
8-bits
XX XX XXXX XXXX XXXX
MSB
2 Don’t Care Page Address
Bits
(PA11 - PA0)
22.
8-bits
XXXX XXXX
LSB
Byte/Buffer Address
(BA9 - BA0/BFA9 - BFA0)
Write Operations
The following block diagram and waveforms illustrate the various write sequences available.
FLASH MEMORY ARRAY
PAGE (512-/528-BYTES)
BUFFER 1 TO
MAIN MEMORY
PAGE PROGRAM
BUFFER 2 TO
MAIN MEMORY
PAGE PROGRAM
BUFFER 1 (512-/528-BYTES)
BUFFER 2 (512-/528-BYTES)
BUFFER 2
WRITE
BUFFER 1
WRITE
I/O INTERFACE
SI
35
3500N–DFLASH–05/10
22.1
Buffer Write
Completes writing into selected buffer
CS
BINARY PAGE SIZE
15 DON'T CARE + BFA8-BFA0
SI (INPUT)
22.2
X
CMD
X···X, BFA9-8
BFA7-0
n
n+1
Last Byte
Buffer to Main Memory Page Program (Data from Buffer Programmed into Flash Page)
Starts self-timed erase/program operation
CS
BINARY PAGE SIZE
A20-A9 + 9 DON'T CARE BITS
SI (INPUT)
CMD
PA11-6
PA5-0, XX
Each transition
represents eight bits
23.
XXXX XX
n = 1st byte read
n+1 = 2nd byte read
Read Operations
The following block diagram and waveforms illustrate the various read sequences available.
FLASH MEMORY ARRAY
PAGE (512-/528-BYTES)
MAIN MEMORY
PAGE TO
BUFFER 2
MAIN MEMORY
PAGE TO
BUFFER 1
BUFFER 1 (512-/528-BYTES)
BUFFER 2 (512-/528-BYTES)
BUFFER 1
READ
MAIN MEMORY
PAGE READ
BUFFER 2
READ
I/O INTERFACE
SO
36
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
23.1
Main Memory Page Read
CS
ADDRESS FOR BINARY PAGE SIZE
A15-A8
A20-A16
A7-A0
SI (INPUT)
CMD
PA11-6
, PA5-0, BA9-8
BA7-0
X
X
4 Dummy Bytes
SO (OUTPUT)
23.2
n
n+1
Main Memory Page to Buffer Transfer (Data from Flash Page Read into Buffer)
Starts reading page data into buffer
CS
BINARY PAGE SIZE
A20-A9 + 9 DON'T CARE BITS
SI (INPUT)
CMD
PA11-6
PA5-0, XX
XXXX XXXX
SO (OUTPUT)
23.3
Buffer Read
CS
BINARY PAGE SIZE
15 DON'T CARE + BFA8-BFA0
SI (INPUT)
CMD
X
X..X, BFA9-8
BFA7- 0
X
No Dummy Byte (opcodes D1H and D3H)
1 Dummy Byte (opcodes D4H and D6H)
SO (OUTPUT)
n
n+1
Each transition
represents eights bits
37
3500N–DFLASH–05/10
24.
Detailed Bit-level Read Waveform –
Atmel RapidS Serial Interface Mode 0/Mode 3
24.1
Continuous Array Read (Legacy Opcode E8H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34
62 63 64 65 66 67 68 69 70 71 72
SCK
OPCODE
SI
1
1
1
0
1
ADDRESS BITS
0
0
0
MSB
A
A
A
A
A
A
32 DON'T CARE BITS
A
A
A
MSB
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
D
D
D
D
D
D
D
D
MSB
BIT 0 OF
PAGE n+1
BIT 4095/4223
OF PAGE n
24.2
D
MSB
Continuous Array Read (Opcode 0BH)
CS
0
1
2
3
4
5
6
7
8
9
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
10 11 12
SCK
OPCODE
SI
0
0
0
0
1
ADDRESS BITS A20 - A0
0
1
1
MSB
A
A
A
A
A
A
A
DON'T CARE
A
A
MSB
X
X
X
X
X
X
X
X
MSB
DATA BYTE 1
HIGH-IMPEDANCE
SO
D
D
D
MSB
24.3
D
D
D
D
D
D
D
MSB
Continuous Array Read (Low Frequency: Opcode 03H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40
SCK
OPCODE
SI
0
0
0
0
0
ADDRESS BITS A20-A0
0
MSB
1
1
A
A
A
A
A
A
A
A
A
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
MSB
38
D
D
D
D
D
D
D
D
D
MSB
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
24.4
Main Memory Page Read (Opcode: D2H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34
62 63 64 65 66 67 68 69 70 71 72
SCK
OPCODE
SI
1
1
0
1
0
ADDRESS BITS
0
1
0
A
MSB
A
A
A
A
A
32 DON'T CARE BITS
A
A
A
MSB
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
D
D
D
D
D
D
D
MSB
24.5
D
D
MSB
Buffer Read (Opcode D4H or D6H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
SCK
ADDRESS BITS
BINARY PAGE SIZE = 15 DON'T CARE + BFA8-BFA0
STANDARD ATMEL DATAFLASH PAGE SIZE =
14 DON'T CARE + BFA9-BFA0
OPCODE
SI
1
1
0
1
0
1
0
0
MSB
X
X
X
X
X
X
A
A
A
MSB
DON'T CARE
X
X
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
D
D
MSB
24.6
D
D
D
D
D
D
D
MSB
Buffer Read (Low Frequency: Opcode D1H or D3H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40
SCK
ADDRESS BITS
BINARY PAGE SIZE = 15 DON'T CARE + BFA8-BFA0
STANDARD ATMEL DATAFLASH PAGE SIZE =
14 DON'T CARE + BFA9-BFA0
OPCODE
SI
1
1
0
1
0
0
MSB
0
1
X
X
X
X
X
X
A
A
A
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
MSB
D
D
D
D
D
D
D
D
D
MSB
39
3500N–DFLASH–05/10
24.7
Read Sector Protection Register (Opcode 32H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40
SCK
OPCODE
SI
0
0
1
1
0
DON'T CARE
0
1
0
X
MSB
X
X
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
D
D
D
D
D
D
D
MSB
24.8
D
MSB
Read Sector Lockdown Register (Opcode 35H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40
SCK
OPCODE
SI
0
0
1
1
0
DON'T CARE
1
0
1
X
MSB
X
X
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
D
D
D
D
D
D
D
MSB
24.9
D
MSB
Read Security Register (Opcode 77H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12
29 30 31 32 33 34 35 36 37 38 39 40
SCK
OPCODE
SI
0
1
1
1
0
DON'T CARE
1
MSB
1
1
X
X
X
X
X
X
X
X
X
MSB
DATA BYTE 1
SO
HIGH-IMPEDANCE
D
MSB
40
D
D
D
D
D
D
D
D
MSB
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
24.10 Status Register Read (Opcode D7H)
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
SCK
OPCODE
SI
1
1
0
1
0
1
1
1
MSB
STATUS REGISTER DATA
SO
HIGH-IMPEDANCE
D
D
D
D
D
D
D
MSB
STATUS REGISTER DATA
D
D
D
D
D
D
D
D
MSB
D
D
D
MSB
24.11 Manufacturer and Device Read (Opcode 9FH)
CS
0
6
7
8
14 15 16
22 23 24
30 31 32
38
SCK
OPCODE
SI
SO
9FH
HIGH-IMPEDANCE
Note: Each transition
1FH
DEVICE ID BYTE 1
DEVICE ID BYTE 2
00H
shown for SI and SO represents one byte (8-bits)
41
3500N–DFLASH–05/10
25.
Auto Page Rewrite Flowchart
Figure 25-1. Algorithm for Programming or Reprogramming of the Entire Array Sequentially
START
provide address
and data
BUFFER WRITE
(84H, 87H)
MAIN MEMORY PAGE PROGRAM
THROUGH BUFFER
(82H, 85H)
BUFFER TO MAIN
MEMORY PAGE PROGRAM
(83H, 86H)
END
Notes:
1. This type of algorithm is used for applications in which the entire array is programmed sequentially, filling the array
page-by-page
2. A page can be written using either a Main Memory Page Program operation or a Buffer Write operation followed by
a Buffer to Main Memory Page Program operation
3. The algorithm above shows the programming of a single page. The algorithm will be repeated sequentially for each
page within the entire array
42
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
Figure 25-2. Algorithm for Randomly Modifying Data
START
provide address of
page to modify
MAIN MEMORY PAGE
TO BUFFER TRANSFER
(53H, 55H)
If planning to modify multiple
bytes currently stored within
a page of the Flash array
BUFFER WRITE
(84H, 87H)
MAIN MEMORY PAGE PROGRAM
THROUGH BUFFER
(82H, 85H)
BUFFER TO MAIN
MEMORY PAGE PROGRAM
(83H, 86H)
(2)
AUTO PAGE REWRITE
(58H, 59H)
INCREMENT PAGE
(2)
ADDRESS POINTER
END
Notes:
1. To preserve data integrity, each page of an Atmel DataFlash sector must be updated/rewritten at least once within
every 10,000 cumulative page erase and program operations
2. A Page Address Pointer must be maintained to indicate which page is to be rewritten. The Auto Page Rewrite command must use the address specified by the Page Address Pointer
3. Other algorithms can be used to rewrite portions of the Flash array. Low-power applications may choose to wait
until 10,000 cumulative page erase and program operations have accumulated before rewriting all pages of the
sector. See application note AN-4 (“Using Atmel’s Serial DataFlash”) for more details
43
3500N–DFLASH–05/10
26.
Ordering Information
26.1
Ordering Code Detail
AT 4 5 DB 1 6 1 D – SSU
Atmel Designator
Product Family
Device Grade
U = Matte Sn lead finish, industrial
temperature range (-40°C to +85°C)
Package Option
Device Density
M
S
T
C
16 = 16-megabit
Interface
=
=
=
=
8-lead, 6 x 5 x 1mm MLF (VDFN)
8-lead, 0.209" wide SOIC
28-lead, TSOP
24 Ball BGA
1 = Serial
Device Revision
26.2
Green Package Options (Pb/Halide-free/RoHS Compliant)
Ordering Code(1)(2)
Package
AT45DB161D-MU
AT45DB161D-MU-SL954(3)
AT45DB161D-MU-SL955(4)
8M1-A
AT45DB161D-SU
AT45DB161D-SU-SL954(3)
AT45DB161D-SU-SL955(4)
8S2
AT45DB161D-TU
28T
AT45DB161D-MU-2.5
8M1-A
AT45DB161D-SU-2.5
8S2
AT45DB161D-TU-2.5
28T
AT45DB161D-CU
Notes:
24C1
Lead Finish
Operating Voltage
fSCK (MHz)
Matte Sn
2.7V to 3.6V
66
Operation Range
Industrial
(-40C to 85C)
2.7V to 3.6V
Matte Sn
2.5V to 3.6V
50
Matte Sn
2.7V to 3.6V
66
1. The shipping carrier option is not marked on the devices
2. Standard parts are shipped with the page size set to 528-bytes. The user is able to configure these parts to a 512byte page size if desired
3. Parts ordered with suffix SL954 are shipped in bulk with the page size set to 512-bytes. Parts will have a 954 or
SL954 marked on them
4. Parts ordered with suffix SL955 are shipped in tape and reel with the page size set to 512-bytes. Parts will have a
954 or SL954 marked on them
Package Type
44
8M1-A
8-pad, 6 x 5 x 1.00mm Body, Very Thin Dual Flat Package No Lead MLF™ (VDFN)
8S2
8-lead, 0.209” Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC)
28T
28-lead, 8mm x 13.4mm, Plastic Thin Small Outline Package, Type I (TSOP)
24C1
24-Ball, 6mm x 8mm x 1,4mm Ball Grid Array with a 1mm pitch 5 x 5 Ball Matrix
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
27.
Packaging Information
27.1
8M1-A – MLF (VDFN)
D
D1
0
Pin 1 ID
E
E1
SIDE VIEW
TOP VIEW
A3
A2
A1
A
0.08 C
Pin #1 Notch
(0.20 R)
e
COMMON DIMENSIONS
(Unit of Measure = mm)
0.45
D2
E2
b
L
K
BOTTOM VIEW
SYMBOL
MIN
NOM
MAX
A
–
0.85
1.00
A1
–
–
0.05
A2
0.65 TYP
A3
0.20 TYP
b
0.35
0.40
0.48
D
5.90
6.00
6.10
D1
5.70
5.75
5.80
D2
3.20
3.40
3.60
E
4.90
5.00
5.10
E1
4.70
4.75
4.80
E2
3.80
4.00
4.20
e
NOTE
1.27
L
0.50
0.60
0.75
0
–
–
12o
K
0.25
–
–
8/28/08
Package Drawing Contact:
[email protected]
TITLE
8M1-A, 8-pad, 6 x 5 x 1.00mm Body, Thermally
Enhanced Plastic Very Thin Dual Flat No
Lead Package (VDFN)
GPC
YBR
DRAWING NO.
8M1-A
REV.
D
45
3500N–DFLASH–05/10
27.2
8S2 – EIAJ SOIC
C
1
E
E1
L
N
θ
TOP VIEW
END VIEW
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
SYMBOL
A1
D
SIDE VIEW
NOTE
1.70
2.16
A1
0.05
0.25
b
0.35
0.48
4
C
0.15
0.35
4
D
5.13
5.35
E1
5.18
5.40
E
7.70
8.26
L
0.51
0.85
θ
0°
2
8°
1.27 BSC
3
This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information.
Mismatch of the upper and lower dies and resin burrs aren't included.
Determines the true geometric position.
Values b,C apply to plated terminal. The standard thickness of the plating layer shall measure between 0.007 to .021 mm.
Package Drawing Contact:
[email protected]
46
MAX
NOM
A
e
Notes: 1.
2.
3.
4.
MIN
TITLE
8S2, 8-lead, 0.208” Body, Plastic Small
Outline Package (EIAJ)
GPC
STN
4/15/08
DRAWING NO. REV.
8S2
F
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
27.3
28T – TSOP, Type 1
PIN 1
0º ~ 5º
c
Pin 1 Identifier Area
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
SYMBOL
Notes: 1. This package conforms to JEDEC reference MO-183.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15mm per side and on D1 is 0.25mm per side.
3. Lead coplanarity is 0.10mm maximum.
MIN
MAX
NOM
A
–
–
1.20
A1
0.05
–
0.15
A2
0.90
1.00
1.05
NOTE
D
13.20
13.40
13.60
D1
11.70
11.80
11.90
Note 2
Note 2
E
7.90
8.00
8.10
L
0.50
0.60
0.70
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
0.55 BASIC
12/06/02
Package Drawing Contact:
[email protected]
TITLE
28T, 28-lead (8 x 13.4mm) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
28T
C
47
3500N–DFLASH–05/10
27.4
24C1 - Ball Grid Array
Dimensions in Millimeters and (Inches).
Controlling dimension: Millimeters.
6.10(0.240)
5.90(0.232)
A1 ID
8.10(0.319)
7.90(0.311)
SIDE VIEW
0.30 (0.012)MIN
TOP VIEW
1.40 (0.055) MAX
1.00 (0.039) REF
4.0 (0.157)
5
4
3
2
1
2.00 (0.079) REF
A
B
1.00 (0.0394) BSC
NON-ACCUMULATIVE
4.0 (0.157)
C
D
E
0.46 (0.018)
DIA BALL TYP
1.00 (0.0394) BSC
NON-ACCUMULATIVE
BOTTOM VIEW
04/11/01
Package Drawing Contact:
[email protected]
48
TITLE
24C1, 24-ball (5 x 5 Array), 6 x 8 x 1.4 mm Body, 1.0mm
Ball Pitch Chip-scale Ball Grid Array Package (CBGA)
DRAWING NO.
24C1
REV.
A
Atmel AT45DB161D
3500N–DFLASH–05/10
Atmel AT45DB161D
28.
Revision History
Doc. Rev.
Date
Comments
05/2010
Changed tSE (Typ) 1.6 to 0.7 and (Max) 5 to 1.3
Changed tCE (Typ) TBD to 12 and (Max) TBD to 25
Changed from 10,000 to 20,000 cumulative page erase/program operations and added the
please contact Atmel statement in section 11.3
3500M
04/2009
Updated Absolute Maximum Ratings
Added 24C1 24 Ball BGA package Option
Deleted Atmel DataFlash Card Package Option
Removed Chip Erase Errata
3500L
03/2009
Changed Deep Power-Down Current values
- Increased typical value from 5µA to 15µA
- Increased maximum value from 15µA to 25µA
3500K
02/2009
Changed tDIS (Typ and Max) to 27ns and 35ns, respectively
3500J
04/2008
Added part number ordering code details for suffixes SL954/955
Added ordering code details
3500I
08/2007
Added additional text to “power of 2” binary page size option
Removed SER/BYTE statement from SI and SO pin descriptions in Table 2-1
Changed tVSCL from 50µs to 70µs
Changed tXFR and tCOMP values from 400µs to 200µs
Changed tRDPD from 30µs to 35µs
3500H
08/2006
Added tSCKR and tSCKF parameters to Table 18-4
3500G
08/2006
Added errata regarding Chip Erase
3500F
07/2006
Corrected typographical errors
3500E
05/2006
Added Legacy Status Register Read opcode 57H. This opcode is supported on devices with date
code 0636 and later
3500D
02/2006
Changed part 2 of the device ID to 00H
3500C
01/2006
Added text, in “Programming the Configuration Register”, to indicate that power cycling is
required to switch to “power of 2” page size after the opcode enable has been executed
Added “Legacy Commands” table
3500B
11/2005
Added 2.5V - 3.6V operating range
Changed tVCSL from 30µs to 50µs min
Changed tPUW from 10ms to 20ms max
Changed tDIS from 8ns to 6ns max (2.7V device)
Changed tV from 8ns to 6ns max (2.7V device)
3500A
09/2005
Initial Document Release
3500N
49
3500N–DFLASH–05/10
29.
Errata
29.1
No Errata Conditions
50
Atmel AT45DB161D
3500N–DFLASH–05/10
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 487-2600
www.atmel.com
Atmel Asia Limited
Unit 01-5 & 16, 19F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81) (3) 3523-3551
Fax: (+81) (3) 3523-7581
Sales Contact
www.atmel.com/contacts
Literature Requests
www.atmel.com/literature
Product Contacts
Technical Support
[email protected]
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2010 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, Everywhere You Are ®, DataFlash ®, RapidS ™
and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
3500N–DFLASH–05/10