SF10A02 thru SF10A06 Pb Free Plating Product ® Pb SF10A02 thru SF10A06 10.0 Ampere Super Fast Rectifiers for Power Chargers TO-220AC Features ¬ Special for E-Bike charger application ¬ Low forward voltage drop ¬ High current capability ¬ Low reverse leakage current ¬ High surge current capability Unit : inch (mm) .419(10.66) .196(5.00) .387(9.85) .163(4.16) .139(3.55) MIN .054(1.39) .038(0.96) .019(0.50) .624(15.87) .548(13.93) .50(12.7)MIN .269(6.85) .177(4.5)MAX Mechanical Data ¬ Case:TO-220AC/TO-220C-2P Heatsink ¬ Epoxy: UL 94V-0 rate flame retardant ¬ Terminals: Solderable per MIL-STD-202 method 208 ¬ Polarity: As marked on diode body ¬ Mounting position: Any ¬ Weight: 2.03 gram approximately .226(5.75) .045(1.15) .025(0.65)MAX .1(2.54) .1(2.54) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. o SF10A06 UNIT 400 600 V 140 280 420 V 200 400 600 V SYMBOL SF10A02 Maximum Recurrent Peak Reverse Voltage VRRM 200 Maximum RMS Voltage VRMS VDC Maximum DC Blocking Voltage Maximum Average Forward Rectified o Current TC=100 C SF10A04 IF(AV) 10.0 A IFSM 100 A Peak Forward Surge Current, 8.3ms single Half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 10.0 A VF 0.95 o Maximum DC Reverse Current @TJ=25 C o At Rated DC Blocking Voltage @TJ=125 C IR 1.3 uA 250 uA nS Trr 35 Typical junction Capacitance (Note 2) CJ 65 Operating Junction and Storage Temperature Range V 10.0 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 3) 1.5 R JC 2.2 TJ, TSTG -55 to +150 pF o CW o C NOTES : (1) Reverse recovery test conditions IF = 0.5A, IR = 1.0A, Irr = 0.25A. (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts DC. (3) Thermal Resistance junction to case. Rev.02 © 2006 Thinki Semiconductor Co.,Ltd. Page 1/2 http://www.thinkisemi.com/ SF10A02 thru SF10A06 ® FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 10 8 6 4 2 60 Hz Resistive or Inductive load 0 Pulse Width 8.3ms Single Half-Sire-Wave (JEDEC Method) 80 60 40 20 0 0 50 100 150 1 LEAD TEMPERATURE, C 1000 SF10A02 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 100 SF10A04 10 SF10A06 o TJ=25 C PULSE WIDTH=300uS 1% DUTY CYCLE 0.1 0.2 0.4 0.6 0.8 1.0 1.2 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1 10 NUMBER OF CYCLES AT 60Hz o 1.4 o TJ=125 C 100 10 o TJ=25 C 1 0.1 1.6 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1000 o TJ = 25 C f = 1.0 MHZ Vsig = 50mVp-p 100 10 0.1 1.0 4.0 10 100 REVERSE VOLTAGE, VOLTS Rev.02 © 2006 Thinki Semiconductor Co.,Ltd. Page 2/2 http://www.thinkisemi.com/