AD AD8582

a
+5 Volt, Parallel Input
Complete Dual 12-Bit DAC
AD8582
FEATURES
Complete Dual 12-Bit DAC
No External Components
Single +5 Volt Operation
1 mV/Bit with 4.095 V Full Scale
True Voltage Output, ±5 mA Drive
Very Low Power: 5 mW
FUNCTIONAL BLOCK DIAGRAM
AD8582
APPLICATIONS
Digitally Controlled Calibration
Portable Equipment
Servo Controls
Process Control Equipment
PC Peripherals
DAC A
REGISTER
CS
A/B
INPUT A
REGISTER
12
DATA
VDD
12
LDA
2
12-BIT
DAC A
VOUTA
VREF
REFERENCE
INPUT B
REGISTER
12
DAC B
REGISTER
LDB
12-BIT
DAC B
VOUTB
AGND
RST MSB
DGND
GENERAL DESCRIPTION
The AD8582 is a complete, parallel input, dual 12-bit, voltage
output DAC designed to operate from a single +5 volt supply.
Built using a CBCMOS process, this monolithic DAC offers the
user low cost, and ease-of-use in +5 volt only systems.
Included on the chip, in addition to the DACs, are a rail-to-rail
amplifier, latch and reference. The reference (VREF) is trimmed
to 2.5 volts output, and the on-chip amplifier gains up the DAC
output to 4.095 volts full scale. The user needs only supply a +5
volt supply.
The AD8582 is coded natural binary. The op amp output
swings from 0 volt to +4.095 volts for a one-millivolt-per-bit
resolution, and is capable of driving ± 5 mA. Operation down to
4.3 V is possible with output load currents less than 1 mA.
The high speed parallel data interface connects to the fastest
processors without wait states. The double-buffered input structure allows the user to load the input registers one at a time,
then a single load strobe tied to both LDA + LDB inputs will
update both DAC outputs simultaneously. LDA and LDB can
also be activated independently to immediately update their respective DAC registers. An address input decodes DAC A or
DAC B when the chip select CS input is strobed. An asynchronous reset input sets the output to zero scale. The MSB bit can
be used to establish a preset to midscale when the reset input is
strobed.
The AD8582 is available in the 24-pin plastic DIP and the surface mount SOIC-24. Each part is fully specified for operation
over –40°C to +85°C, and the full +5 V ± 5% power supply
range.
5.0
4.6
4.4
VDD = +5V
T = –55°C, +25°C, +85°C
1.5
LINEARITY ERROR – LSB
VDD MIN – Volts
4.8
2.0
∆∆VFS ≤ 1 LSB
DATA = FFFH
TA = +25°C
PROPER OPERATION
WHEN VDD SUPPLY
VOLTAGE ABOVE
CURVE
4.2
A
1.0
0.5
0.0
–0.5
–1.0
= +25°C & +85°C
= –55°C
–1.5
4.0
0.01
0.1
1.0
10
OUTPUT LOAD CURRENT – mA
100
Figure 1. Minimum Supply Voltage vs. Load
–2.0
0
1024
2048
3072
4096
DIGITAL INPUT CODE – Decimal
Figure 2. Linearity Error vs. Digital Code and Temperature
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD8582–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V
DD
= +5.0 V ± 5%, RL = No Load, –40°C ≤ TA ≤ +85°C, unless otherwise noted)
Parameter
Symbol
Condition
Min
STATIC PERFORMANCE
Resolution
Relative Accuracy
Differential Nonlinearity
Zero-Scale Error
Full-Scale Voltage
Full-Scale Tempco
N
INL
DNL
VZSE
VFS
TCVFS
Note 1
12
–2
–1
MATCHING PERFORMANCE
Linearity Matching Error
∆VFSA/B
REFERENCE OUTPUT
Output Voltage
Output Source Current
Line Rejection
Load Regulation
VREF
IREF
LNREJ
LDREG
ANALOG OUTPUT
Output Current
Load Regulation at Half Scale
Capacitive Load
IOUT
LDREG
CL
DYNAMIC CHARACTERISTICS3
Crosstalk
Voltage Output Settling Time5
Digital Feedthrough
CT
tS
FT
LOGIC INPUTS
Logic Input Low Voltage
Logic Input High Voltage
Input Leakage Current
Input Capacitance
VIL
VIH
IIL
CIL
TIMING SPECIFICATIONS3, 6
Chip Select Pulse Width
DAC Select Setup
DAC Select Hold
Data Setup
Data Hold
Load Setup
Load Hold
Load Pulse Width
Reset Pulse Width
tCSW
tAS
tAH
tDS
tDH
tLS
tLH
tLDW
tRSW
SUPPLY CHARACTERISTICS
Positive Supply Current
IDD
Power Dissipation7
PDISS
Power Supply Sensitivity
PSS
Monotonic
Data = 000H
Data = FFFH,2
Notes 2 and 3
4.079
Typ
Max
Units
± 3/4
± 3/4
+0.2
4.095
± 16
+2
+1
+3
4.111
Bits
LSB
LSB
mV
V
ppm/°C
±1
2.484
2.500
Note 4
IREF = 0 mA to 5 mA
Data = 800H
RL = 402 Ω to ∞, Data = 800H
No Oscillation3
1
500
LSB
2.516
–5
0.08
0.1
V
mA
%/V
%/mA
±5
3
mA
LSB
pF
>64
16
35
To ± 1 LSB of Final Value
Signal Measured at DAC Output, While
Changing Data (LDA = LDB = “1”)
dB
µs
nV s
0.8
2.4
10
10
Note 3
30
30
0
30
10
20
10
20
30
VIH = 2.4 V, VIL = 0.8 V
VIL = 0 V, VDD = +5 V
VIH = 2.4 V, VIL = 0.8 V
VIL = 0 V, VDD = +5 V
∆VDD = ± 5%
V
V
µA
pF
ns
ns
ns
ns
ns
ns
ns
ns
ns
4
1
20
5
0.002
7
2
35
10
0.004
mA
mA
mW
mW
%/%
NOTES
1
1 LSB = 1 mV for 0 V to +4.095 V output range.
2
Includes internal voltage reference error.
3
These parameters are guaranteed by design and not subject to production testing.
4
Very little sink current is available at the V REF pin. Use external buffer if setting up a virtual ground.
5
Settling time is not guaranteed for the first six codes 0 through 5.
6
All input control signals are specified with t R = tF = 5 ns (10% to 90% of +5 V) and timed from a voltage level of 1.6 V.
7
Power dissipation is a calculated value I DD × 5 V.
Specifications subject to change without notice.
–2–
REV. 0
AD8582
PIN DESCRIPTION
ABSOLUTE MAXIMUM RATINGS*
VDD to DGND & AGND . . . . . . . . . . . . . . . . . . . –0.3 V, +7 V
Logic Inputs to DGND . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V
VOUT to AGND . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V
VREF to AGND . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD
IOUT Short Circuit to GND . . . . . . . . . . . . . . . . . . . . . . 50 mA
Package Power Dissipation . . . . . . . . . . . . . . . (TJ max–TA)/θJA
Thermal Resistance, θJA
24-Pin Plastic DIP Package (N-24) . . . . . . . . . . . . . 62°C/W
24-Lead SOIC Package (SOL-24) . . . . . . . . . . . . . . 73°C/W
Maximum Junction Temperature (TJ max) . . . . . . . . . . 150°C
Operating Temperature Range . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . +300°C
Pin No. Name
1, 24
VOUTA
VOUTB
Voltage outputs from the DACs. Fixed
output voltage range of 0 V to 4.095 V
with 1 mV/LSB. An internal
temperature stabilized reference
maintains a fixed full-scale voltage
independent of time, temperature and
power supply variations.
AGND Analog Ground. Ground reference for
the internal bandgap reference voltage,
the DAC, and the output buffer.
DGND Digital ground for input logic.
LDA,
Load DAC register strobes. Transfers
LDB
input register data to the DAC registers.
Active low inputs, Level sensitive latch.
May be connected together to doublebuffer load DAC registers.
MSB
Digital Input: High presets DAC
registers to half scale (800H), Low
clears DAC registers to zero (000H)
upon RST assertion.
RST
Active low digital input that clears the
DAC register to zero, setting the DAC
to minimum scale when MSB pin = 0,
or half-scale when MSB pin = 1.
DB0–11 Twelve Binary Data Bit Inputs. DB11 is
the MSB and DB0 is the LSB.
CS
Chip Select. Active low input.
A/B
Select DAC A = 0 or DAC B = 1.
VDD
Positive Supply. Nominal value +5 V, ± 5%.
Nominal 2.5 V reference output
VREF
voltage. This node must be buffered if
required to drive external loads.
2
3
4, 21
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
5
tCSW
CS
tAH
tAS
6
A/B
tDH
tDS
D0–D11
tLDW
tLH
tLS
LDA, LDB
7–18
tRSW
19
20
22
23
RST
tS
tS
VOUT
± 1LSB
ERROR BAND
Timing Diagram
PIN CONFIGURATIONS
N-24
SOL-24
24-Pin Plastic DIP
24-Pin SOIC
ORDERING INFORMATION*
Model
Temperature
Range
Package
Description
Description
Package
Option
1
VOUTA
AD8582AN
–40°C to +85°C 24-Pin Plastic DIP N-24
AD8582AR
–40°C to +85°C 24-Lead SOIC
SOL-24
AD8582Chips +25°C
Die
*For die specifications contact your local Analog Devices sales office. The
AD8582 contains 1270 transistors.
1
AGND
2
23 VREF
DGND
3
22 VDD
LDA
4
21 LDB
MSB
5
RST
6
DB0
7
DB1
8
DB2
9
20
AD8582
12
13
16 DB9
15 DB8
DB4 11
14 DB7
DB5 12
13 DB6
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8582 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–3–
A/B
AD8582
TOP VIEW
(Not to Scale)
19
CS
TOP VIEW
(Not to Scale) 18 DB11
17 DB10
DB3 10
REV. 0
24
24 VOUTB
WARNING!
ESD SENSITIVE DEVICE
AD8582
Table I. Control Logic Truth Table
CS
A/B
LDA
LDB
RST
MSB
Input Register
DAC Register
L
L
L
L
H
H
X
X
H
L
H
L
H
X
X
X
X
X
H
H
L
H
L
^
X
X
X
H
H
H
L
L
^
X
X
X
H
H
H
H
H
H
L
L
^
X
X
X
X
X
X
L
H
X
Write to A
Write to B
Write to A
Write to B
Latched
Latched
Reset to Zero Scale
Reset to Midscale
Latch Reset Value
Latched
Latched
A Transparent
B Transparent
A & B Transparent
Latched
Reset to Zero Scale
Reset to Midscale
Latch Reset Value
^Denotes positive edge triggered.
OPERATION
BANDGAP
REFERENCE
The AD8582 is a complete, ready-to-use dual 12-bit digital-toanalog converter. Only one +5 V power supply is necessary for
operation. It contains two voltage-switched, 12-bit, lasertrimmed digital-to-analog converters, a curvature-corrected
bandgap reference, rail-to-rail output op amps, input registers,
and DAC registers. The parallel data interface consists of twelve
data bits, DB0–DB11, an address select pin A/B, two load
strobe pins (LDA, LDB) and an active low CS strobe. In addition an asynchronous RST pin will set all DAC register bits to
zero causing the VOUT to become zero volts, or to midscale for
trimming applications when the MSB pin is programmed to
Logic 1. This function is useful for power on reset or system
failure recovery to a known state.
AMPLIFIER SECTION
The internal DAC’s output is buffered by a low power consumption precision amplifier. This low power amplifier contains
a differential PNP pair input stage which provides low offset
voltage and low noise, as well as the ability to amplify the zeroscale DAC output voltages. The rail-to-rail amplifier is configured in a gain of 1.6384 (= 4.095 V/2.5 V) in order to set the
4.095 volt full-scale output (1 mV/LSB). See Figure 3 for an
equivalent circuit schematic of the analog section.
VOLTAGE SWITCHED 12-BIT
R-2R D/A CONVERTER
RAIL-TO-RAIL
OUTPUT
AMPLIFIER
2R
VOUT
R
BUFFER
R2
2R
R
2R
R1
AV = 4.095/2.5
= 1.638V/V
2R
SPDT
N CH FET
SWITCHES
D/A CONVERTER SECTION
The internal DAC is a 12-bit voltage-mode device with an
output that swings from AGND potential to the 2.5 volt internal bandgap voltage. It uses a laser trimmed R-2R
ladder which is switched by N channel MOSFETs. The output voltage of the DAC has a constant resistance independent
of digital input code. The DAC output (not available to the
user) is internally connected to the rail-to-rail output op amp.
VREF
2.5V
2R
Figure 3. Equivalent Schematic of Analog Portion
OUTPUT SECTION
The rail-to-rail output stage of this amplifier has been designed
to provide precision performance while operating near either
power supply. Figure 4 shows an equivalent output schematic of
the rail-to-rail amplifier with its N channel pull-down FETs that
will pull an output load directly to GND. The output sourcing
current is provided by a P channel pull-up device that can supply GND terminated loads, especially important at the –5%
supply tolerance value of 4.75 volts.
VDD
P-CH
N-CH
The op amp has a 16 µs typical settling time to 0.01%. There
are slight differences in settling time for negative slewing signals
versus positive. See the oscilloscope photos in the Typical Performances section of this data sheet.
VOUT
AGND
Figure 4. Equivalent Analog Output Circuit
–4–
REV. 0
AD8582
Figures 5 and 6 in the typical performance characteristics section provide information on output swing performance near
ground and full-scale as a function of load. In addition to resistive load driving capability, the amplifier has also been carefully
designed and characterized for up to 500 pF capacitive load
driving capability.
One advantage of the rail-to-rail output amplifiers used in the
AD8582 is the wide range of usable supply voltage. The part is
fully specified and tested over temperature for operation from
+4.75 V to +5.25 V. If reduced linearity and source current
capability near full scale can be tolerated, operation of the
AD8582 is possible down to +4.3 volts. The minimum operating supply voltage versus load current plot, in Figure 1, provides information for operation below VDD = +4.75 V.
REFERENCE SECTION
The internal 2.5 V curvature-corrected bandgap voltage reference is laser trimmed for both initial accuracy and low temperature coefficient. The voltage generated by the reference is
available at the VREF pin. Since VREF is not intended to drive external loads, it must be buffered. The equivalent emitter follower output circuit of the VREF pin is shown in Figure 3.
TIMING AND CONTROL
The input registers are level triggered and acquire data from the
data bus during the time period when CS is low. The input register selected is determined by the A/B select pin, see Table I.
for a complete description. When CS goes high, the data is
latched into the register and held until CS returns low. The
minimum time required for the data to be present on the bus
before CS returns high is called the data setup time (tDS) as seen
in Timing Diagram. The data hold time (tDH) is the amount
of time that the data has to remain on the bus after CS goes
high. The high speed timing offered by the AD8582 provides
for direct interface with no wait states in all but the fastest
microprocessors.
Bypassing the VREF pin will improve noise performance; however, bypassing is not required for proper operation. Figure 8
shows broadband noise performance.
POWER SUPPLY
The very low power consumption of the AD8582 is a direct result of a circuit design optimizing use of the CBCMOS process.
By using the low power characteristics of the CMOS for the
logic, and the low noise, tight matching of the complementary
bipolar transistors good analog accuracy is achieved.
The data from the input registers is transferred to the DAC registers by the active low LDA and LDB pins. If these inputs are
tied together, a single logic input can perform a double buffer
update of the DAC registers, which in turn simultaneously
changes the analog output voltages to a new value. If the LDA
and LDB pins are wired low, they become transparent. In this
mode the input register data will directly control the output
voltages. Refer to the Control Logic Truth Table for a com-
For power-consumption sensitive applications it is important to
note that the internal power consumption of the AD8582 is
strongly dependent on the actual logic-input voltage levels
present on the DB0–DB11, CS, A/B, MSB, LDA, LDB and
RST pins. Since these inputs are standard CMOS logic structures they contribute static power dissipation dependent on the
actual driving logic VOH and VOL voltage levels. The graph in
Figure 9 shows the effect on total AD8582 supply current as a
function of the actual value of input logic voltage. Consequently, for optimum dissipation use of CMOS logic versus
TTL provides minimal dissipation in the static state. A VINL =
0 V on the DB0–11 pins provides the lowest standby dissipation
of 1 mA typical with a +5 V power supply.
plete description.
Unipolar Output Operation
This is the basic mode of operation for the AD8582. The
AD8582 has been designed to drive loads as low as 820Ω in parallel with 500 pF. The code table for this operation is shown in
Table II.
As with any analog system, it is recommended that the AD8582
power supply be bypassed on the same PC card that contains
the chip. Figure 10 shows the power supply rejection versus frequency performance. This should be taken into account when
using higher frequency switched-mode power supplies with
ripple frequencies of 100 kHz and higher.
REV. 0
Table II. Unipolar Code Table
–5–
Hexadecimal
Number in DAC
Register
Decimal Number
in DAC Register
Analog Output
Voltage (V)
FFF
801
800
7FF
000
4095
2049
2048
2047
0
+ 4.095
+ 2.049
+ 2.048
+ 2.047
0
AD8582–Typical Performance Characteristics
OUTPUT PULL-DOWN VOLTAGE – mV
RL TIED TO AGND
DATA = FFFH
3
2
RL TIED TO +5V
DATA = 000H
1
0
10
1
TA = +85°C
TA = –40°C
0.1
100
1k
10k
LOAD RESISTANCE – Ω
10
100
POWER SUPPLY REJECTION – dB
OUTPUT NOISE VOLTAGE – 200µV/DIV
TA = +25°C
SUPPLY CURRENT – mA
VDD = +4.75V
VDD = +5V
3
2
0
5
204810 TO 204710
OUTPUT
2.048
VOUT – Volts
1
2
3
4
LOGIC VOLTAGE VALUE – Volts
5
0
LDB
90
VDD = +5V
3
TA = +25°C
2
10
0%
0
20µs
1V
Figure 11. Midscale Transition
Performance
40
20
0
10
100
1k
10k
FREQUENCY – Hz
100k
Figure 10. Power Supply Rejection
vs. Frequency
5
0
15µs
4
1
TA = +25°C
DATA = FFFH
60
DATA
5V
5
100
3
VDD = +5V ±200mV AC
80
Figure 9. Supply Current vs. Logic
Input Voltage
INPUT
LD
Figure 8. Broadband Noise
2
Figure 7. IOUT vs. VOUT
0
TIME – 500ns/DIV
1
100
4
TIME = 100µs/DIV
2.008
NEGATIVE
CURRENT
LIMIT
OUTPUT VOLTAGE – Volts
1
2.018
–40
Figure 6. Pull-Down Voltage vs.
Output Sink Current Capability
TA = +25°C
NBW = 630kHz
2.028
–20
1000
5
2.038
DATA = 800H
RL TIED TO +2V
0
OUTPUT SINK CURRENT – µA
Figure 5. Output Swing vs. Load
0
20
–80
1
100k
40
–60
TA = +25°C
0.01
10
POSITIVE0
CURRENT0
LIMIT0
60
OUTPUT CURRENT – mA
4
VDD = +5V
DATA = 000H
TIME = 20µs/DIV
Figure 12. Large Signal Settling Time
–6–
OUTPUT VOLTAGE
1mV/DIV
VDD = +5V
TA = +25°C
OUTPUT VOLTAGE – Volts
80
100
5
VDD = +5V
TA = +25°C
TIME – 5µs/DIV
Figure 13. Output Voltage Rise
Time Detail
REV. 0
AD8582
TUE = ΣINL+ZS+FS
SS = 297 UNITS
V = +4.75V
DD
T = +25°C
A
40
35
0
FREQUENCY
30
15µs
25
20
15
10
4.115
FULL-SCALE OUTPUT – Volts
5
OUTPUT VOLTAGE
1mV/DIV
DATA
45
VDD = +5V
TA = +25°C
0
4.105
4.100
σAVG +1σ
4.095
4.090
4.085
σAVG –1σ
4.080
5
TIME – 5µs/DIV
VDD = +4.75V
NO LOAD
SS = 298 UNITS
4.110
–8 –7 –6 –5 –4 –3 –2 –1
0
4.075
–50
1
–25
TOTAL UNADJUSTED ERROR – mV
Figure 14. Output Voltage Fall
Time Detail
1
0
–1
–50
0
25
50
75
TEMPERATURE – °C
100
H
10
1.0
125
1
σAVG +2σ
0
AVG
–1
–2
σAVG –2σ
125
–3
10
Figure 17. Zero-Scale Voltage vs.
Temperature
100
VDD = +5V
SS = 135 UNITS
DATA = FFFH
2
0.1
–25
75
3
VDD = +5V
TA = +25°C
DATA = FFF
NOMINAL FULL-SCALE
VOLTAGE CHANGE – mV
OUTPUT NOISE DENSITY – µV/ Hz
ZERO-SCALE OUTPUT – Volts
2
50
Figure 16. Full-Scale Voltage vs.
Temperature
100
VDD = +4.75V
NO LOAD
SS = 298 UNITS
25
TEMPERATURE – °C
Figure 15. Total Unadjusted Error
Histogram
3
0
AVG
100
1k
10k
FREQUENCY – Hz
0
100k
100
200
300
400
500
HOURS OF OPERATION AT +150°C
600
Figure 19. Long-Term Drift
Accelerated by Burn-In
Figure 18. Output Voltage Noise
Density vs. Frequency
8
6
VDD = +5.25V
∞ TA = +25°C
RL = ∞
VDD
5
VDD = +5.00V
4
0V
3
VREF
0V
VDD = +4.75V
2
10
–25
0
25
50
75
100
125
0
5µs
CS = HIGH
100
90
10
0%
10mV
2V
0
–50
1
VDD = +5V
0%
1
5V
1µs
VOUT
10mV/DIV
SUPPLY CURRENT – mA
2V
100
90
DATA
VDATA = +2.4V
NO LOAD
7
TIME – 1µs/DIV
TIME – 5µs/DIV
TEMPERATURE – °C
Figure 20. Supply Current vs.
Temperature
REV. 0
Figure 21. Reference Startup vs.
Time
–7–
Figure 22. Digital Feedthrough vs.
Time
AD8582
6
4
σAVG +1σ
AVG
–2
–4
–6
–8
–10
–50
σAVG –1σ
–25
25
50
75
0
TEMPERATURE – °C
100
σAVG +1σ
AVG
–0.002
–0.003
–0.004
σAVG –1σ
–0.005
–50
125
∆VDD = +4.75V
∆IL = 5mA
–0.001
–25
0
25
50
75
100
∆ VDD = +4.75 TO +5.25V
0.08
0.06
AVG
0.04
0.02
σAVG – 1σ
0.00
–50
125
–25
0
25
50
75
100
125
TEMPERATURE – °C
TEMPERATURE – °C
Figure 23. Reference Error vs.
Temperature
σAVG +1σ
Figure 24. Reference Load Regulation
vs. Temperature
Figure 25. Reference Line Regulation
vs. Temperature
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
N-24
24-Pin Narrow Body Plastic DIP
PIN 1
24
13
1
12
0.280 (7.11)
0.240 (6.10)
1.275 (32.30)
1.125 (28.60)
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.325 (8.25)
0.300 (7.62)
0.195 (4.95)
0.115 (2.93)
0.150
(3.81)
MIN
0.200 (5.05)
0.125 (3.18)
0.022 (0.558)
0.014 (0.356)
0.100 (2.54)
BSC
0.070 (1.77)
0.045 (1.15)
SEATING
PLANE
0.015 (0.381)
0.008 (0.204)
SOL-24
24-Lead Wide Body SOIC
13
24
0.2992 (7.60)
0.2914 (7.40)
PIN 1
1
12
0.0118 (0.30)
0.0040 (0.10)
0.0500 (1.27)
BSC
0.4193 (10.65)
0.3937 (10.00)
0.1043 (2.65)
0.0926 (2.35)
0.6141 (15.60)
0.5985 (15.20)
0.0192 (0.49)
0.0138 (0.35)
–8–
PRINTED IN U.S.A.
0
REF LINE REGULATION – %/Volt
REF LOAD REGULATION – %/mA
REFERENCE ERROR – mV
8
2
0.10
0.000
VDD = +4.75V
C1869–18–12/93
10
0.0125 (0.32)
0.0091 (0.23)
0.0291 (0.74)
x 45°
0.0098 (0.25)
8°
0°
0.0500 (1.27)
0.0157 (0.40)
REV. 0