AZ DISPLAYS, INC. SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY PART NUMBER: AGM9624A DATE: September 6, 2005 Page 1 of 8 AZ DISPLAYS, INC. AGM9624A General Specification Driving IC S6B0724A Interace With Paraller MPU 8080 Series! Display Specification Display Dot Matrix :96*24 Display Mode:Positive/Transflective/FSTN Type Viewing Angle :6:00 Clock Display Duty:1/33 Driving Bias:1/6 Driving Voltage:7.5V Mechanical Characteristics(Unit:mm) Extenal Dimension:27.09* 17.76*1.7 View Area:24.09* 8.26 Dots Size:0.19*0.0.195 Dots Pitch:0.22* 0.22 Page 2 of 8 MAX 6.00*1.0 6. 79 26 0. 25 0. 50 PI TCH 0. 5*25=12. 50 FONT UV TAPE I C( S6B0724) ADHESI VE TAPE CHAMFER 0. 19 0. 22 FPC Connect Si de STI FFENR 0. 30 0. 05 3.00 1 12.00 1.50 6. 80 SI LI CON 0.50 0. 25 BACK 96*24DOTS 0.195 0. 55*2 0.22 21. 09( A. A) 5.63 11.26 0.2 17.76 0.2 5.26(A.A) 8.26(V.A) MAX1. 70 13. 50 0. 20 NO. SYMBOL 1 V0 2 V4 3 V3 4 V2 5 V1 6 C27 C2+ 8 C1+ 9 C110 C3+ 11 VOUT 12 VSS 13 VDD 14 D7 15 D6 16 D5 17 D4 18 D3 19 D2 20 D1 21 D0 22 E_RDB 23 RW_WRB RS 24 25 / RES 26 / CS1 AGM9624A AGM9624A Page 3 of 8 AZ DISPLAYS, INC. AZ DISPLAYS, INC. 27. 09 0. 2 24. 09( V. A) AZ DISPLAYS, INC. AGM9624A Absolute Maximum Ratings Item Symbol Power supply voltage VDD-VSS Input voltage VIN Operating temperature range TA Storage temperature range TSTO *Wide temperature range is available Standard - 0 VSS -20 -30 Unit 5.5 VDD +70 +80 V " Interface Pin Description Pin No Symbol I/O Function 26 CS1B I This is the chip select signal .When CS1B=# L” and CS2= # H”,then the chip select becomes active,and data/command I/O is enabled 25 RESETB I When RESETB is set to “ L” ,the setting are initialized The RESETB operation is performed by the RESETB signal level 24 RS I Select register. 0:Instruction register (for write) Busy flag &address counter(for read) 1:Data register(for write and read). 23 RW-WRB I Read/write select signal. 22 E-RDB I Operation (data read/write) enable signal. 21 DB0 I/O 20 DB1 19 DB2 18 DB3 17 DB4 16 DB5 15 DB6 14 DB7 13 VDD Supply 12 VSS Supply 11 VOUT O DC/DC voltage converter output 10 C3+ O Capacitor3+ for internal DC/DC voltage converter 9 C1- O Capacitor1- for internal DC/DC voltage converter 8 C1+ O Capacitor1+ for internal DC/DC voltage converter 7 C2+ O Capacitor2+ for internal DC/DC voltage converter 6 C2- O Capacitor2- for internal DC/DC voltage converter This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected,then D7 serves as the serial data input terminal and D6 serves as the serial clock input terminal.At this time,D0-D5 are set to high impedence. When the chip select is inactive,D0 to D7 are set to high impedance. Power supply for logic Ground. Page 4 of 8 AZ DISPLAYS, INC. 5 V1 4 V2 3 V3 LCD driver supply voltages.The voltage determined by LCD cell is impedangce-converted by a resistive driver or an operation amplifier for application .Voltages should be the following relationship: V0>V1>V2>V3>V4>VSS When the on-chip operating power circuit is on,the following are given to V1 to V4 by the on-chip power circuit .Voltage Supply 2 1 V4 V0 AGM9624A selection is performed by the set LCD bias command. LCD BIAS V1 V2 V3 V4 1/5BIAS 4/5V0 3/5V0 2/5V0 1/5V0 1/6 BIAS 5/6V0 4/6 V0 2/6 V0 1/6 V0 1/7 BIAS 6/7 V0 5/7 V0 2/7 V0 1/7 V0 1/8 BIAS 7/8 V0 6/8 V0 2/8 V0 1/8 V0 1/9 BIAS 8/9 V0 7/9 V0 2/9 V0 1/9 V0 Page 5 of 8 AZ DISPLAYS, INC. AGM9624A Electrical Characteristics DC Characteristics Page 6 of 8 AZ DISPLAYS, INC. AGM9624A AC Characteristics Page 7 of 8 AZ DISPLAYS, INC. AGM9624A Application Example 1. Page 8 of 8