10 MHz Bandwidth, 640 MSPS Dual Continuous Time Sigma-Delta Modulator AD9267 FEATURES AVDD PDWNB PDWNA DRVDD LVDS DRIVERS OR±A VIN+A Σ-Δ MODULATOR VIN–A D3±A D0±A PLL_LOCKED VREF CFILT AD9267 PLLMULT4 PLLMULT3 PLLMULT2 PHASELOCKED LOOP CLK+ CLK– DCO± VIN–B Σ-Δ MODULATOR VIN+B SERIAL INTERFACE Baseband quadrature receivers: CDMA2000, W-CDMA, multicarrier GSM/EDGE, 802.16x, and LTE Quadrature sampling instrumentation AGND GENERAL DESCRIPTION SDIO/ PLLMULT1 SCLK/ PLLMULT0 D3±B D0±B OR±B CSB DGND Figure 1. The AD9267 is a dual continuous time (CT) sigma-delta (Σ-Δ) modulator with −88 dBc of dynamic range over 10 MHz real or 20 MHz complex bandwidth. The combination of high dynamic range, wide bandwidth, and characteristics unique to the continuous time Σ-Δ modulator architecture makes the AD9267 an ideal solution for wireless communication systems. The AD9267 operates on a 1.8 V power supply, consuming 416 mW. The AD9267 is available in a 64-lead LFCSP and is specified over the industrial temperature range (−40°C to +85°C). The AD9267 has a resistive input impedance that significantly relaxes the requirements of the driver amplifier. In addition, a 32× oversampled fifth-order continuous time loop filter attenuates out-of-band signals and aliases, reducing the need for external filters at the input. The low noise figure of 15 dB relaxes the linearity requirements of the front-end signal chain components, and the high dynamic range reduces the need for an automatic gain control (AGC) loop. 1. A differential input clock controls all internal conversion cycles. An external clock input or the integrated integer-N PLL provides the 640 MHz internal clock needed for the oversampled continuous time Σ-Δ modulator. The digital output data is presented as 4-bit, LVDS at 640 MSPS in twos complement format. A data clock output (DCO) is provided to ensure proper latch timing with receiving logic. Additional digital signal processing may be required on the 4-bit modulator output to remove the out-of-band noise and to reduce the sample rate. 07773-001 APPLICATIONS FUNCTIONAL BLOCK DIAGRAM LVDS DRIVERS SNR: 83 dB (85 dBFS) to 10 MHz input SFDR: −88 dBc to 10 MHz input Noise figure: 15 dB Input impedance: 1 kΩ Power: 416 mW 10 MHz real or 20 MHz complex bandwidth 1.8 V analog supply operation On-chip PLL clock multiplier On-chip voltage reference Twos complement data format 640 MSPS, 4-bit LVDS data output Serial control interface (SPI) PRODUCT HIGHLIGHTS 2. 3. 4. 5. 6. Continuous time Σ-Δ architecture efficiently achieves high dynamic range and wide bandwidth. Passive input structure reduces or eliminates the requirements for a driver amplifier. An oversampling ratio of 32× and high order loop filter provide excellent alias rejection, reducing or eliminating the need for antialiasing filters. Operates from a single 1.8 V power supply. A standard serial port interface (SPI) supports various product features and functions. Features a low pin count, high speed LVDS interface with data output clock. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2009 Analog Devices, Inc. All rights reserved. AD9267 TABLE OF CONTENTS Features .............................................................................................. 1 Equivalent Circuits ......................................................................... 12 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 13 General Description ......................................................................... 1 Analog Input Considerations ................................................... 13 Functional Block Diagram .............................................................. 1 Clock Input Considerations ...................................................... 14 Product Highlights ........................................................................... 1 Power Dissipation and Standby Mode .................................... 17 Revision History ............................................................................... 2 Digital Outputs ........................................................................... 17 Specifications..................................................................................... 3 Timing ......................................................................................... 18 DC Specifications ......................................................................... 3 Serial Port Interface (SPI) .............................................................. 19 AC Specifications.......................................................................... 4 Configuration Using the SPI ..................................................... 19 Digital Specifications ................................................................... 5 Hardware Interface..................................................................... 20 Switching Specifications .............................................................. 6 Applications Information .............................................................. 21 Absolute Maximum Ratings............................................................ 7 Filtering Requirement ................................................................ 21 Thermal Resistance ...................................................................... 7 Memory Map .................................................................................. 23 ESD Caution .................................................................................. 7 Memory Map Definitions ......................................................... 23 Pin Configuration and Function Descriptions ............................. 8 Outline Dimensions ....................................................................... 24 Typical Performance Characteristics ............................................. 9 Ordering Guide .......................................................................... 24 REVISION HISTORY 7/09—Revision 0: Initial Version Rev. 0 | Page 2 of 24 AD9267 SPECIFICATIONS DC SPECIFICATIONS All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN1 = −2.0 dBFS, unless otherwise noted. Table 1. Parameter RESOLUTION ANALOG INPUT BANDWIDTH ACCURACY No Missing Codes Offset Error Gain Error Integral Nonlinearity (INL)2 MATCHING CHARACTERISTIC Offset Error Gain Error TEMPERATURE DRIFT Offset Error Gain Error INTERNAL VOLTAGE REFERENCE ANALOG INPUT Input Span, VREF = 0.5 V Input Resistance Input Common Mode POWER SUPPLIES Supply Voltage AVDD CVDD DVDD DRVDD Supply Current IAVDD2, PLL Enabled IAVDD2, PLL Disabled ICVDD2, PLL Enabled ICVDD2, PLL Disabled IDVDD2 IDRVDD2 POWER CONSUMPTION Sine Wave Input2, PLL Disabled Sine Wave Input, PLL Enabled Power-Down Power Standby Power Sleep Power 1 2 Temp Full Min Typ 16 10 Max Unit Bits MHz Full Full Full 25°C Guaranteed ±0.025 ±0.2 ±0.7 ±2.5 ±1.5 % FSR % FSR LSB Full Full ±0.035 ±0.2 ±0.2 ±1.2 % FSR % FSR Full Full Full 496 ±1.5 ±47 500 505 ppm/°C ppm/°C mV Full Full Full 1.7 2 1 1.8 1.9 V p-p diff kΩ V Full Full Full Full 1.7 1.7 1.7 1.7 1.8 1.8 1.8 1.8 1.9 1.9 1.9 1.9 V V V V Full Full Full Full Full Full 150.7 151.2 57 8 71.5 0.26 162 161 63 9.2 78 0.3 mA mA mA mA mA mA Full Full 25°C 25°C Full 416 503 110 9 3 4 mW mW mW mW mW Input power is referenced to full scale. Therefore, all measurements were taken with a 2 dB signal below full scale, unless otherwise noted. Measured with a low input frequency, full-scale sine wave with approximately 5 pF loading on each output bit. Rev. 0 | Page 3 of 24 AD9267 AC SPECIFICATIONS All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN1 = −2.0 dBFS, unless otherwise noted. Table 2. Parameter2 SIGNAL-TO-NOISE RATIO (SNR) fIN = 2.4 MHz fIN = 4.2 MHz fIN = 8.4 MHz SPURIOUS-FREE DYNAMIC RANGE (WORST SECOND OR THIRD HARMONIC)3 fIN = 2.4 MHz fIN = 4.2 MHz fIN = 8.4 MHz NOISE SPECTRAL DENSITY AIN = −2 dBFS AIN = −40 dBFS NOISE FIGURE2, 4 AIN = −2 dBFS AIN = −40 dBFS TWO-TONE SFDR fIN1 = 1.8 MHz @ −8 dBFS, fIN2 = 2.1 MHz @ −8 dBFS fIN1 = 3.7 MHz @ −8 dBFS, fIN2 = 4.2 MHz @ −8 dBFS fIN1 = 7.2 MHz @ −8 dBFS, fIN2 = 8.4 MHz @ −8 dBFS ANALOG INPUT BANDWIDTH 1 Temp Min Typ Full 25°C 25°C 81 83 83 83 Rev. 0 | Page 4 of 24 Unit dB dB dB Full 25°C 25°C −88 −88 <−120 −80 dBc dBc dBc Full Full −155 −156 −153 −155 dBFS/Hz dBFS/Hz 25°C 25°C 16 15 dB dB 25°C 25°C 25°C 25°C −89.5 −93 −87 dBc dBc dBc MHz Input power is referenced to full scale. Therefore, all measurements were taken with a 2 dB signal below full scale, unless otherwise noted. See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions. 3 Spurious-free dynamic range excluding the second or third harmonic is limited by the FFT size, <−120 dBFS. 4 Noise figure with respect to 50 Ω. AD9267 internal impedance is 1000 Ω differential. See the AN-835 for a definition. 2 Max 10 AD9267 DIGITAL SPECIFICATIONS All power supplies set to 1.8 V, 640 MHz sample rate, 2 V p-p differential input, 0.5 V internal reference, PLL disabled, AIN = −2.0 dBFS, unless otherwise noted. Table 3. Parameter DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−) Logic Compliance Differential Input Voltage Input Common-Mode Range High Level Input Current Low Level Input Current Input Resistance Input Capacitance LOGIC INPUTS (SCLK) High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current Input Resistance Input Capacitance LOGIC INPUTS (SDIO, CSB, RESET) High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current Input Resistance Input Capacitance DIGITAL OUTPUTS (D0±x to D3±x) ANSI-644 Logic Compliance Differential Output Voltage (VOD) Output Offset Voltage (VOS) Output Coding (Default) Low Power, Reduced Signal Option Logic Compliance Differential Output Voltage (VOD) Output Offset Voltage (VOS) Output Coding (Default) 1 Temp Min Typ Max Unit 2 V p-p mV μA μA kΩ diff pF CMOS1/LVDS/LVPECL Full Full Full Full Full Full 0.4 0.8 450 −60 −60 +60 +60 20 1 Full Full Full Full Full Full 1.2 0 −50 −10 Full Full Full Full Full Full 1.2 0 −10 +40 DRVDD + 0.3 0.8 −75 +10 V V μA μA kΩ pF DRVDD + 0.3 0.8 +10 +135 V V μA μA kΩ pF 454 1.375 mV V 250 1.30 mV V 30 2 26 5 LVDS Full Full 247 1.125 Twos complement LVDS Full Full 150 1.10 Twos complement For voltage swings beyond the specified range, clamping diodes are recommended. Rev. 0 | Page 5 of 24 AD9267 SWITCHING SPECIFICATIONS AVDD = 1.8 V, DRVDD = 1.8 V, unless otherwise noted. Table 4. Parameter1 CLOCK INPUT PARAMETERS Input CLK Rate CLK± Period CLK± Duty Cycle CLOCK INPUT PARAMETERS Conversion Rate CLK± Period CLK± Duty Cycle DATA OUTPUT PARAMETERS Data Propagation Delay (tPD)2 DCO± Propagation Delay (tDCO) DCO± to Data Skew (tSKEW) Aperture Uncertainty (Jitter, tJ) WAKE-UP TIME Power-Down Power Standby Power Sleep Power OUT-OF-RANGE RECOVERY TIME SERIAL PORT INTERFACE3 SCLK Period (tSCLK) SCLK Pulse Width High Time (tSHIGH) SCLK Pulse Width Low Time (tSLOW) SDIO to SCLK Set-Up Time (tSDS) SDIO to SCLK Hold Time (tSDH) CSB to SCLK Set-Up Time (tSS) CSB to SCLK Hold Time (tSH) Conditions/Comments Using clock multiplier Temp Min Typ Max Unit Full Full Full 30 6.25 40 50 160 33.3 60 MSPS ns % Full Full Full 608 1.48 40 640 1.5625 50 672 1.72 60 MSPS ns % Full Full Full Full 160 -60 180 510 268 200 1 840 570 280 ps ps Ps ps rms Direct clocking 25°C 25°C 25°C 25°C Full Full Full Full Full Full Full 3 9 15 100 Μs μs μs ns 40 16 16 5 2 5 2 1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions. Output propagation delay is measured from CLK± 50% transition to data D0±x to D3±x 50% transition, with 5 pF load. 3 See Figure 42 and the Serial Port Interface (SPI) section. 2 Timing Diagram CLK± tDCO DCO± tSKEW 07773-057 tPD D0±x TO D3±x Figure 2. Timing Diagram Rev. 0 | Page 6 of 24 ns ns ns ns ns ns ns AD9267 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Electrical AVDD to AGND DVDD to DGND DRVDD to DGND AGND to DGND AVDD to DRVDD CVDD to CGND CGND to DGND D0±A to D3±A to DGND D0±B to D3±B to DGND DCO± to DGND OR±A, OR±B to DGND PDWNA to DGND PDWNB to DGND PLLMULTx to DGND SDIO to DGND CSB to AGND SCLK to AGND VIN±A, VIN±B to AGND CLK+, CLK− to CGND Environmental Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 10 sec) Junction Temperature Rating −0.3 V to +2.0 V −0.3 V to +2.0 V −0.3 V to +3.9 V −0.3 V to +0.3 V −3.9 V to +2.0 V −0.3 V to +2.0 V −0.3 V to +0.3 V −0.3 V to +2.0 V −0.3 V to +2.0 V −0.3 V to +2.0 V −0.3 V to +2.0 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +3.9 V −0.3 V to +2.5 V −0.3 V to +2.0 V −65°C to +125°C −40°C to +85°C 300°C 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE The exposed paddle must be soldered to the ground plane for the LFCSP package. Soldering the exposed paddle to the PCB increases the reliability of the solder joints, maximizing the thermal capability of the package. Typical θJA and θJC are specified for a 4-layer board in still air. Airflow increases heat dissipation, effectively reducing θJA. In addition, metal in direct contact with the package leads from metal traces, through holes, ground, and power planes reduces the θJA. Table 6. Thermal Resistance Package Type 64-Lead LFCSP (CP-64-4) ESD CAUTION Rev. 0 | Page 7 of 24 θJA 22 Unit °C/W AD9267 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 CLK+ CGND AGND AVDD VIN–B VIN+B AVDD CFILT VREF AVDD VIN–A VIN+A AVDD AGND RESET CSB PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PIN 1 INDICATOR AD9267 TOP VIEW (Not to Scale) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 SCLK/PLLMULT0 SDIO/PLLMULT1 PLLMULT2 PLLMULT3 PLLMULT4 DVDD DGND DRVDD D3+A D3–A D2+A D2–A D1+A D1–A D0+A D0–A NOTES 1. DNC = DO NOT CONNECT. 2. THE EXPOSED PAD MUST BE SOLDERED TO THE GROUND PLANE FOR THE LFCSP PACKAGE. SOLDERING THE EXPOSED PADDLE TO THE PCB INCREASES THE RELIABILITY OF THE SOLDER JOINTS, MAXIMIZING THE THERMAL CAPACITY OF THE PACKAGE. 07773-003 OR–B OR+B DCO– DCO+ DNC DNC DRVDD DGND DVDD DNC DNC DNC DNC DNC OR–A OR+A 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 CLK– CVDD PDWNA PDWNB PLL_LOCKED DVDD DGND DRVDD D0–B D0+B D1–B D1+B D2–B D2+B D3–B D3+B Figure 3. Pin Configuration Table 7. Pin Function Descriptions Pin No. 1 2 3, 4 5 6, 25, 43 7, 24, 42 8, 23, 41 9 to 16 17, 18 19, 20 21, 22, 26 to 30 31, 32 33 to 40 44, 45, 46 47 48 49 50 51, 62 52, 55, 58, 61 53, 54 56 57 59, 60 63 64 65 Mnemonic CLK− CVDD PDWNA, PDWNB PLL_LOCKED DVDD DGND DRVDD D0−B, D0+B to D3−B, D3+B OR−B, OR+B DCO−, DCO+ DNC OR−A, OR+A D0−A, D0+A to D3−A, D3+A PLLMULT4, PLLMULT3, PLLMULT2 SDIO/PLLMULT1 SCLK/PLLMULT0 CSB RESET AGND AVDD VIN+A, VIN−A VREF CFILT VIN+B, VIN−B CGND CLK+ Exposed paddle (EPAD) Description Differential Clock Input (−). Clock Supply (1.8 V). Power-Down Pins. Active high. PLL Lock Indicator. Digital Supply (1.8 V). Digital Ground. Digital Output Driver Supply Channel B Differential LVDS Data Output Bits. D0+B is the LSB and D3+B is the MSB. Channel B Overrange Indicator Pins. Differential Data Clock Output. Do Not Connect. Channel A Overrange Indicator Pins. Channel A Differential LVDS Data Output Bits. D0+A is the LSB and D3+A is the MSB. PLL Mode Selection Pins. Serial Port Interface Data Input/Output/PLL Mode Selection Pins. Serial Port Interface Clock/PLL Mode Selection Pins. Serial Port Interface Chip Select Pin Active Low. Chip Reset. Analog Ground. Analog Supply (1.8 V). Channel A Analog Input. Voltage Reference Input. Noise Limiting Filter Capacitor. Channel B Analog Input. Clock Ground. Differential Clock Input (+). Analog Ground. (Pin 65 is the exposed thermal pad on the bottom of the package.) The exposed paddle must be soldered to analog ground of the PCB to achieve optimal electrical and thermal performance. Rev. 0 | Page 8 of 24 AD9267 TYPICAL PERFORMANCE CHARACTERISTICS 0 –10 –20 –20 –30 –30 –40 –40 –50 –60 –70 –80 –90 –70 –80 –90 –100 –110 –110 –120 –120 –130 –130 2 3 4 5 6 7 8 9 10 FREQUENCY (MHz) –140 0 0 –10 –20 –20 –30 –30 –40 –40 AMPLITUDE (dBFS) 0 –50 –60 –70 –80 –90 –120 –130 –130 8 9 10 FREQUENCY (MHz) 0 0 –10 –20 –20 –30 –30 –40 –40 AMPLITUDE (dBFS) 0 –50 –60 –70 –80 –90 –130 –140 8 FREQUENCY (MHz) 9 10 07773-006 –120 –130 7 6 7 8 9 10 10 –90 –110 6 5 –80 –120 5 4 –70 –110 4 3 –60 –100 3 2 –50 –100 2 1 Figure 8. Two-Tone FFT with fIN1 = 3.6 MHz, fIN2 = 4.2 MHz –10 1 10 FREQUENCY (MHz) Figure 5. Single-Tone FFT with fIN = 4.2 MHz 0 9 –140 07773-005 –140 7 8 –90 –110 6 7 –80 –120 5 6 –70 –110 4 5 –60 –100 3 4 –50 –100 2 3 Figure 7. Two-Tone FFT with fIN1 = 2.1 MHz, fIN2= 2.4 MHz –10 1 2 FREQUENCY (MHz) Figure 4. Single-Tone FFT with fIN = 2.4 MHz 0 1 07773-010 1 07773-011 0 AMPLITUDE (dBFS) –60 –100 –140 AMPLITUDE (dBFS) –50 07773-009 AMPLITUDE (dBFS) 0 –10 07773-004 AMPLITUDE (dBFS) All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN = −2.0 dBFS, TA = 25°C, unless otherwise noted. The output spectrums shown in Figure 4 through Figure 9 were obtained after 16× decimation at the output of the AD9267 and are shown for a 10 MHz bandwidth. –140 0 1 2 3 4 5 6 7 8 9 FREQUENCY (MHz) Figure 9. Two-Tone FFT with fIN1 = 7.2 MHz, fIN2 = 8.4 MHz Figure 6. Single-Tone FFT with fIN = 8.4 MHz Rev. 0 | Page 9 of 24 AD9267 84.0 –50 83.8 –60 83.6 83.4 –80 SNR (dB) AMPLITUDE (dBFS) –70 –90 –100 83.2 83.0 82.8 82.6 –110 82.4 –120 82.2 –130 150 200 250 300 82.0 FREQUENCY (MHz) 0 1 2 3 4 5 6 7 8 9 07773-043 100 1.90 07773-044 50 07773-042 0 FREQUENCY (MHz) Figure 10. Noise Transfer Function (NTF) Figure 13. Single-Tone SNR vs. Input Frequency 84.0 120 83.8 SFDR (dBFS) 100 83.6 83.4 SNR (dBFS) SNR (dB) SNR/SFDR 80 SFDR (dBc) 60 SNR (dB) 40 83.2 83.0 82.8 82.6 82.4 20 82.2 –90 –80 –70 –60 –50 –40 –30 –20 –10 0 INPUT AMPLITUDE (dBFS) 82.0 1.70 07773-007 1.75 1.80 Figure 14. SNR vs. Input Common-Mode Voltage Figure 11. Single-Tone SNR and SFDR vs. Input Amplitude with fIN = 2.4 MHz 91 83.4 90 83.2 83.0 89 1.9V 82.8 SNR (dB) 88 87 1.8V 82.6 1.8V 82.4 86 82.2 85 1.7V 84 –40 –20 0 20 40 60 TEMPERATURE (°C) 1.7V 82.0 80 100 07773-012 SFDR (dBc) 1.9V 83 –60 1.85 COMMON-MODE VOLTAGE (V) 81.8 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) Figure 15. SNR vs. Temperature Figure 12. SFDR vs. Temperature Rev. 0 | Page 10 of 24 80 100 07773-013 0 –100 AD9267 84 –40 –50 –60 83 2.4MHz 82 8.4MHz SFDR (dBc) SNR (dB) SFDR –70 –80 81 –90 80 SFDR (dBFS) –100 79 –110 –40 –30 –20 –10 INPUT AMPLITUDE (dBFS) 78 4.0 5.0 4.5 7.0 6.0 8.0 7.5 8.5 9.0 10.5 12.5 15.0 17.0 10.0 12.0 14.0 16.0 21.0 PLL DIVIDE RATIO Figure 16. Two-Tone SFDR vs. Input Amplitude with fIN1 = 2.1 MHz, fIN2 = 2.4 MHz 07773-047 –50 07773-046 –120 –60 Figure 18. Single-Tone SNR vs. PLL Divide Ratio with fIN1 = 2.4 MHz, fIN2 = 8.4 MHz –40 0.5 –50 0 –60 –0.5 INL ERROR (LSB) SFDR (dBc) –80 –90 –1.0 –1.5 –2.0 –100 SFDR (dBFS) –120 –60 –50 –40 –30 –20 INPUT AMPLITUDE (dBFS) –10 –3.0 0 8192 16,384 24,576 32,768 40,960 49,152 57,344 65,536 OUTPUT CODE Figure 19. INL with fIN = 2.4 MHz Figure 17. Two-Tone SFDR vs. Input Amplitude with fIN1 = 7.2 MHz, fIN2 = 8.4 MHz Rev. 0 | Page 11 of 24 07773-048 –2.5 –110 07773-045 SFDR –70 AD9267 EQUIVALENT CIRCUITS 1kΩ SCLK 30kΩ 500Ω 500Ω 07773-018 07773-014 2V p-p DIFFERENTIAL 1.8V CM Figure 23. Equivalent SCLK Input Circuit Figure 20. Equivalent Analog Input Circuit CVDD AVDD 26kΩ 1kΩ 10kΩ 10kΩ 90kΩ 30kΩ 07773-019 CVDD CSB CLK– 07773-015 CLK+ Figure 21. Equivalent Clock Input Circuit Figure 24. Equivalent CSB Input Circuit DRVDD V V D– DRVDD D+ V V 1kΩ SDIO Figure 22. Equivalent SDIO Input Circuit 07773-017 07773-016 DGND NOTES 1. D– AND D+ REFERS TO THE D0±x TO D3±x PINS. Figure 25. Equivalent Digital Output Circuit 2.85kΩ 10kΩ TO CURRENT GENERATOR Figure 26. Equivalent VREF Circuit 07773-020 3.5kΩ 10µF Rev. 0 | Page 12 of 24 8.5kΩ 0.5V AD9267 THEORY OF OPERATION The AD9267 uses a continuous time Σ-Δ modulator to convert the analog input to a digital word. The modulator consists of a continuous time loop filter preceding a quantizer (see Figure 27), which samples at fMOD = 640 MSPS. This produces an oversampling ratio (OSR) of 32 for a 10 MHz input bandwidth. The output of the quantizer is fed back to a DAC that ideally cancels the input signal. The incomplete input cancellation residue is filtered by the loop filter and is used to form the next quantizer sample. MODULATOR LOOP FILTER QUANTIZER ADC H(f) 07773-021 DAC – L F (f) LOOP FILTER INP UT Figure 27. Σ-Δ Modulator Overview LF(f) fMOD QUANTIZATION The quantizer produces a nine-level digital word. The quantization noise is spread uniformly over the Nyquist band (see Figure 28) but the feedback loop causes the quantization noise present in the nine-level output to have a nonuniform spectral shape. This noise shaping technique (see Figure 29) pushes the in-band noise out of band; therefore, the amount of quantization noise in the frequency band of interest is minimal. NOISE fMOD OUTPUT H(z) NTF(f) f fMOD 07773-025 + In contrast, the continuous time Σ-Δ modulator used within the AD9267 has inherent antialiasing. The antialiasing property results from sampling occurring at the output of the loop filter (see Figure 31), and thus aliasing occurs at the same point in the loop as quantization noise is injected; aliases are shaped by the same mechanism as quantization noise. The quantization noise transfer function, NTF(f), has zeros in the band of interest and in all alias bands because NTF(f) is a discrete time transfer function, whereas the loop filter transfer function, LF(f), introduces poles only in the band of interest because LF(f) is a continuous time transfer function. The signal transfer function, being the product of NTF(f) and LF(f), only has zeros in all alias bands and therefore suppresses all aliases. Figure 31. Continuous Time Converter Input Common Mode QUANTIZATION NOISE BAND OF INTEREST The analog inputs of the AD9267 are not internally dc biased. In ac-coupled applications, the user must provide this bias externally. Setting the device such that VCM = AVDD is recommended for optimum performance. The analog inputs are 500 Ω resistors and the internal reference loop aims to develop 0.5 V across each input resistor (see Figure 32). With 0 V differential input, the driver sources 1 mA into each analog input. 07773-022 fMOD/2 Figure 28. Quantization Noise NOISE SHAPING 2.3V 07773-023 fMOD/2 BAND OF INTEREST AVDD – 0.5V 1.8V 1.3V VIN+x 500Ω TO LOOP FILTER STAGE 2 Figure 29. Noise Shaping VIN–x ANALOG INPUT CONSIDERATIONS 500Ω 2.3V 1.3V UNDESIRED SIGNAL fS fS/2 ADC 07773-024 DESIRED INPUT 1.8V Figure 30. Discrete Time Converter Rev. 0 | Page 13 of 24 DAC FROM QUANTIZER Figure 32. Input Common Mode 07773-026 The continuous time modulator removes the need for an antialias filter at the input to the AD9267. A discrete time converter aliases signals around the sample clock frequency and its multiples to the band of interest (see Figure 30). An external antialias filter is needed to reject these signals. AD9267 AVDD – 0.5V Differential Input Configurations Optimum performance can be achieved by driving the AD9267 in a differential input configuration. The ADA4937-2 differential driver provides excellent performance and a flexible interface to the ADC. The output common-mode voltage of the ADA4937-2 is easily set by connecting AVDD to the VOCMx pin of the ADA4937-2 (see Figure 33). The noise and linearity of the ADA4937-2 needs important consideration because the system performance may be limited by the ADA4937-2. VCM = AVDD VIN p-p = 2V VIN+x VIN–x 0.5V VREF 10kΩ REF TO LOOP FILTER STAGE 2 AVDD 10µF 500Ω AVDD – 0.5V +1.8V CFILT 07773-029 +5V 500Ω 500Ω 10µF 0.1µF 0.1µF Figure 35. Voltage Reference Loop 200Ω 2V p-p 50Ω VS RT 60.4 200Ω 13 VOCM2 11 7 SIGNAL SOURCE Internal Reference Connection 9 6 ADA4937-2 12 AVDD VIN–x AD9267 VIN+x 15 200Ω 60.4Ω 0.1µF 0.1µF 07773-027 49.9Ω –5V To minimize thermal noise, the internal reference on the AD9267 is an unbuffered 0.5 V. It has an internal 10 kΩ series resistor, which, when externally decoupled with a 10 μF capacitor, limits the noise (see Figure 36). Do not use the unbuffered reference to drive any external circuitry. The internal reference is used by default and when Serial Register 0x18[6] is reset. Figure 33. Differential Input Configuration Using the ADA4937-2 For frequencies offset from dc, where SNR is a key parameter, differential transformer coupling is the recommended input configuration. An example is shown in Figure 34. The center tap of the secondary winding of the transformer is connected to AVDD to bias the analog input. VS SIGNAL SOURCE 1:1 VIN+x RT 50Ω TO CURRENT GENERATOR Figure 36. Internal Reference Configuration External Reference Operation If an external reference is desired, the internal reference can be disabled by setting Serial Register 0x18[6] high. Figure 37 shows an application using the ADR130B as a stable external reference. AD9267 VIN–x ADR130B AVDD 0.1µF 0.5V 10µF 10kΩ AVDD 0.1µF TO CURRENT GENERATOR 07773-031 2V p-p 3.5kΩ 10µF 07773-028 50Ω 8.5kΩ 0.5V 07773-030 The signal characteristics must be considered when selecting a transformer. Most RF transformers saturate at frequencies below a couple of megahertz (MHz), and excessive signal power can cause core saturation, which leads to distortion. 2.85kΩ 10kΩ Figure 37. External Reference Configuration Figure 34. Differential Transformer Configuration Voltage Reference CLOCK INPUT CONSIDERATIONS A stable and accurate 0.5 V voltage reference is built into the AD9267. The reference voltage should be decoupled to minimize the noise bandwidth using a 10 μF capacitor. The reference is used to generate a bias current into a matched resistor such that when used to bias the current in the feedback DAC, a voltage of AVDD − 0.5 V is developed at the internal side of the input resistors (see Figure 35). The current bias circuit should also be decoupled on the CFILT pin with a 10 μF capacitor. For this reason, the VREF voltage should always be 0.5 V. The AD9267 offers two modes of sourcing the ADC sample clock (CLK+ and CLK−). The first mode uses an on-chip clock multiplier that accepts a reference clock operating at the lower input frequency. The on-chip phase-locked loop (PLL) then multiplies the reference clock up to a higher frequency, which is then used to generate all the internal clocks required by the Σ-Δ modulator. The clock multiplier provides a high quality clock that meets the performance requirements of most applications. Using the on-chip clock multiplier removes the burden of generating and distributing the high speed clock. Rev. 0 | Page 14 of 24 AD9267 The CLK± inputs are self-biased to 450 mV (see Figure 21); if dc-coupled, it is important to maintain the specified 450 mV input common-mode voltage. Each input pin can safely swing from 200 mV p-p to 1 V p-p single-ended about the 450 mV common-mode voltage. The recommended clock inputs are CMOS or LVPECL. Another option is to ac couple a differential LVPECL signal to the sample clock input pins, as shown in Figure 40. The AD951x family of clock drivers is recommended because it offers excellent jitter performance. 150Ω 0.1µF 0.1µF CLK AD951x LVPECL DRIVER 0.1µF CLK+ ADC AD9267 100Ω CLK– CLK 240Ω 240Ω 0.1µF 50Ω1 RESISTORS ARE OPTIONAL. Figure 40. Differential LVPECL Sample Clock Internal PLL Clock Distribution Direct Clocking The alternative clocking option available on the AD9267 is to apply a low frequency reference clock and use the on-chip clock multiplier to generate the high frequency fMOD rate. The internal clock architecture is shown in Figure 41. CLK± The default configuration of the AD9267 is for direct clocking where the PLL is bypassed. Figure 38 shows one preferred method for clocking the AD9267. A low jitter clock source is converted from a single-ended signal to a differential signal using an RF transformer. The back-to-back Schottky diodes across the secondary side of the transformer limits clock excursions into the AD9267 to approximately 0.8 V p-p differential. This helps prevent the large voltage swings of the clock from feeding through to other portions of the AD9267 while preserving the fast rise and fall times of the signal, which are critical to achieving low jitter. MINI-CIRCUITS TC1-1-13M+, 1:1 0.1µF XFMR 0.1µF VCO PLL ÷N ÷2 MODULATOR CLOCK 640MSPS PLLENABLE 0x09[2] Figure 41. Internal Clock Architecture The clock multiplication circuit operates such that the VCO outputs a frequency, fVCO, equal to the reference clock input multiplied by N fVCO = (CLK±) × (N) ADC AD9267 where N is the PLL multiplication (PLLMULT) factor. CLK– The Σ-Δ modulator clock frequency, fMOD, is equal to Figure 38. Transformer-Coupled Differential Clock Rev. 0 | Page 15 of 24 fMOD = fVCO ÷ 2 07773-040 PLLMULT 0x0A[5:0] CLK+ SCHOTTKY DIODES: 0.1µF HSM2812 LOOP FILTER PHASE DETECTOR DIVIDER 07773-053 50Ω SCHOTTKY DIODES: HSM2812 Figure 39. Single-Ended Clock 50Ω1 In either case, using the on-chip clock multiplier to generate the Σ-Δ modulator clock rate or directly sourcing the clock, any deviation from 640 MHz results in a change in input bandwidth. The input range of the clock is limited to 640 MHz ± 5%. 0.1µF ADC AD9267 CLK– 0.1µF CLOCK INPUT Bandwidth = fMOD ÷ 64 CLOCK INPUT CLK+ 50Ω CLOCK INPUT The specified clock rate of the Σ-Δ modulator, fMOD, is 640 MHz. The clock rate possesses a direct relationship with the available input bandwidth of the ADC. 0.1µF CLOCK INPUT 07773-055 In either case, when using the on-chip clock multiplier or sourcing the high speed clock directly, it is necessary that the clock source have low jitter to maximize the Σ-Δ modulator noise performance. High speed, high resolution ADCs and modulators are sensitive to the quality of the clock input. As jitter increases, the SNR performance of the AD9267 degrades from that specified in Table 2. The jitter inherent to the part due to the PLL root sum squares with any external clock jitter, thereby degrading performance. To prevent jitter from dominating the performance of the AD9267, the input clock source should be no greater than 1 ps rms of jitter. If a differential clock is not available, the AD9267 can be driven by a single-ended signal into the CLK+ terminal with the CLK− terminal ac-coupled to ground. Figure 39 shows the circuit configuration. 07773-054 The second mode bypasses the clock multiplier circuitry and allows the clock to be directly sourced. This mode enables the user to source a very high quality clock directly to the Σ-Δ modulator. Sourcing the clock directly may be necessary in demanding applications that require the lowest possible output noise. Refer to Figure 18, which shows the degradation in SNR performance for the various PLL settings. AD9267 The reference clock, CLK±, is limited to 30 MHz to 160 MHz when configured to use the on-chip clock multiplier. Given the input range of the reference clock and the available multiplication factors, the fVCO is approximately 1280 MHz. This results in the desired fMOD rate of 640 MHz with a 50% duty cycle. The PLL of the AD9267 can be controlled through either the serial port interface or the PLLMULTx pins. For serial port interface control, Register 0x09 and Register 0x0A are used. Before the PLL enable register bit (PLLENABLE) is set, the PLL multiplication factor should be programmed into Register 0x0A[5:0]. After setting the PLLENABLE bit, the PLL locks and reports a locked state in Register 0x0A[7]. If the PLL multiplication factor is changed, the PLL enable bit should be reset and set again. Some common clock multiplication factors are shown in Table 8. The recommended sequence for enabling and programming the on-chip clock multiplier is as follows: 1. 2. 3. Apply a reference clock to the CLK± pins. Program the PLL multiplication factor in Register 0x0A[5:0]. See Table 8. Enable the PLL; Register 0x09 = 04 (decimal). External PLL Control At power-up, the serial interface is disabled until the first serial port access. If the serial interface is disabled, the PLLMULTx pins control the PLL multiplication factor. The five PLLMULTx pins (Pin 44 to Pin 48) offer all the available multiplication factors. If all PLLMULTx pins are tied high, the PLL is disabled and the AD9267 assumes the high frequency modulator clock rate that is applied to the CLK± pins. Table 10 shows the relationship between PLLMULTx pins and the PLL multiplication factor. PLL Autoband Select The PLL VCO has a wide operating range that is covered by overlapping frequency bands. For any desired VCO output frequency, there are multiple valid PLL band select values. The AD9267 possesses an automatic PLL band select feature on chip that determines the optimal PLL band setting. This feature can be enabled by writing to Register 0x0A[6] and is the recommended configuration with the PLL clocking option. Table 8. PLL Multiplication Factors 0x0A[5:0] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PLLMULT (N) 8 8 8 8 8 8 8 8 9 10 10 12 12 14 15 16 17 18 18 20 21 21 21 24 25 25 25 28 28 30 30 32 0x0A[5:0] 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 PLLMULT (N) 32 34 34 34 34 34 34 34 34 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 Table 9. Common Modulator Clock Multiplication Factors CLK± (MHz) 30.72 39.3216 52.00 61.44 76.80 78.00 78.6432 89.60 92.16 122.88 134.40 153.60 157.2864 Rev. 0 | Page 16 of 24 0x0A[5:0] (PLLMULT) 42 32 25 21 17 17 16 15 14 10 10 8 8 fVCO (MHz) 1290.24 1258.29 1300.00 1290.24 1305.60 1326.00 1258.29 1344.00 1290.24 1228.80 1344.00 1228.80 1258.29 fMOD (MHz) 645.12 629.15 650.00 645.12 652.80 663.00 629.15 672.00 645.12 614.40 672.00 614.40 629.15 BW (MHz) 10.08 9.83 10.16 10.08 10.20 10.36 9.83 10.50 10.08 9.60 10.50 9.60 9.83 AD9267 Table 10. PLLMULTx Pins and PLL Multiplication Factor DIGITAL OUTPUTS PLLMULT[4:0] Pins 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 to 30 31 Digital Output Format PLL Multiplication Factors (N) 8 9 10 12 14 15 16 17 18 20 21 24 25 28 30 32 34 42 Direct clocking The AD9267 digital bus outputs twos complement, single data rate, LVDS data at 640 MSPS. The output is four bits wide per channel. The AD9267 supports both the ANSI-644 and a reduced power data format similar to the IEEE1596.3 standard. The default configuration at power-up is ANSI-644. This can be changed to a low power reduced signal option by addressing Register 0x14[7], DRVSTD. The LVDS driver current is derived on chip and sets the output current at each output equal to a nominal 3.5 mA for the ANSI644 standard. A 100 Ω differential termination resistor placed at the LVDS receiver inputs result in a nominal 350 mV swing at the receiver. In the reduced power data format, the output swing is limited to 200 mV and the resulting output current into the 100 Ω termination is 2 mA. As a result of the reduced LVDS voltage swing, an additional 25% digital power savings can be achieved over the ANSI-644 standard. POWER DISSIPATION AND STANDBY MODE The AD9267 consumes 415 mW. This power consumption can be further reduced by configuring the chip in channel powerdown, standby, or sleep mode. The low power modes turn off internal blocks of the chip including the reference. As a result, the wake-up time is dependent on the amount of circuitry that is turned off. Fewer internal circuits powered down result in proportionally shorter wake-up time. The different low power modes are shown in Table 11. In the standby mode, all clock related activity is disabled in addition to each channel; the references and LVDS outputs remain powered up to ensure a short recovery and link integrity, respectively. During sleep mode, all internal circuits are powered down, putting the device into its lowest power mode; the LVDS outputs are disabled. Each ADC channel can be independently powered down or both channels can be set simultaneously by writing to the channel index, Register 0x05[1:0]. Additionally, if the serial port interface is not available, each channel can be independently configured by tying the PDWNA (Pin 3) or PDWNB (Pin 4) high. Table 11. Low Power Modes Mode Normal Channel Power-Down Standby Sleep 0x08[1:0] 0x0 0x1 0x2 0x3 Analog Circuitry On Off Off Off Clock On On Off Off Ref. On On On Off The desired output format can be selected by addressing Register 0x14[7], DRVSTD. The LVDSTERM bits, Register 0x15[5:4], provide either 100 Ω or 200 Ω, or no termination at the output of the data bus. Selecting the appropriate termination resistor is important to allow maximum signal transfer and to minimize reflections for signal integrity. This can be achieved by selecting a termination resistor that impedance matches the termination of the receiver. Overrange (OR) Condition An overrange condition can be triggered by large in-band signals that exceed the full-scale range of the Σ-Δ modulator, or it can be triggered by out-of-band signals gained by the transfer characteristics of the modulator. Figure 43 shows the signal transfer function of the Σ-Δ modulator. The modulator output possesses out-of-band gain above 10 MHz. As a result, the input signal may exceed full scale for input frequencies beyond 10 MHz and the ADC may be in an overrange state. The OR±x pins serve as indicators for the overrange condition. The OR±x pins are synchronous outputs that are updated at the output data rate. The pins indicate whether an overrange condition has occurred within the AD9267. Ideally, OR±x should be latched on the falling edge of DCO± to ensure proper setup-andhold time. However, because an overrange condition typically extends well beyond one clock cycle (that is, does not toggle at the DCO± rate); data can usually be successfully detected on the rising edge of DCO± or monitored asynchronously. The user has the ability to select how the overrange condition is reported and this is controlled through the SPI bits (AUTORST, OR_IND1, and OR_IND2) in Register 0x111[7:5]. The two modes of operation are normal and data valid mode. Rev. 0 | Page 17 of 24 AD9267 In normal operation mode, the analog input can toggle the OR±x pin for a number of clock cycles as it approaches full scale. The OR±x pin is a pulse-width modulated (PWM) signal; therefore, as the analog input increases in amplitude, the duration of OR±x pin toggling increases. Eventually, when the OR±x pin is high for an extended period of time, the ADC overloads; thus, there is little correspondence between analog input and digital output. In this mode, the duration of the OR±x pin can be used as a coarse indicator to the signal amplitude at the input of the ADC. In data valid mode, the OR±x pin remains high when there are no memory access operations taking place, such as internal calibration or factory memory transfer, and the inputs of the ADC are within the operating range. In either modes of operation, the AUTORST bit can be enabled and this automatically resets the modulator in an overload condition. Because the OR±x signal is a PWM signal and the toggling of OR±x does not always indicate an overload condition, the modulator only resets after 16 consecutive clock cycles where OR±x remains high or if the loop filter becomes saturated. The OR±x pin remains high until the automatic reset has completed. If the AD9267 is used in a system that incorporates automatic gain control (AGC), the OR±x signals can be used to indicate that the signal amplitude should be reduced. This may be particularly effective for use in maximizing the signal dynamic range if the signal includes high occurrence components that occasionally exceed full scale by a small amount. TIMING The AD9267 provides latched data outputs with a latency of seven clock cycles. The AD9267 also provides a data clock output (DCO±) pin intended to assist in capturing the data in an external register. The data outputs are valid on the rising edge of DCO±, unless changed by setting Serial Register 0x16[7] (see the Serial Port Interface (SPI) section). See Figure 2 for a graphical timing description. Table 12. OR±x Conditions Reset State Normal Reset Off Data Valid Reset Off Normal Reset On Data Valid Reset On AUTORST 0 0 1 1 OR_IND1 0 1 0 1 OR_IND2 0 1 0 1 Function If overrange: OR±x = 1, else OR±x = 0 If memory access: OR±x = 0, else OR±x = 1 If overrange or reset: OR±x = 1, else OR±x = 0 If memory access, or reset: OR±x = 0, else OR±x = 1 Rev. 0 | Page 18 of 24 AD9267 SERIAL PORT INTERFACE (SPI) additional external timing. When CSB is tied high, SPI functions are placed in a high impedance mode. The AD9267 serial port interface (SPI) allows the user to configure the converter for specific functions or operations through a structured register space provided inside the ADC. This provides the user added flexibility and customization depending on the application. Addresses are accessed via the serial port and can be written to or read from via the port. Memory is organized into bytes that are further divided into fields, as documented in the Memory Map section. For detailed operational information, see the see the AN-877 Application Note, Interfacing to High Speed ADCs via SPI. During an instruction phase, a 16-bit instruction is transmitted. Data follows the instruction phase and the length is determined by the W0 bit and the W1 bit. All data is composed of 8-bit words. The first bit of each individual byte of serial data indicates whether a read or write command is issued. This allows the serial data input/output (SDIO) pin to change direction from an input to an output. In addition to word length, the instruction phase determines if the serial frame is a read or write operation, allowing the serial port to be used to both program the chip as well as to read the contents of the on-chip memory. If the instruction is a readback operation, performing a readback causes the serial data input/ output (SDIO) pin to change direction from an input to an output at the appropriate point in the serial frame. CONFIGURATION USING THE SPI As summarized in Table 13, three pins define the SPI of this ADC. The SCLK pin synchronizes the read and write data presented to the ADC. The SDIO pin allows data to be sent and read from the internal ADC memory map registers. The CSB pin is an active low control that enables or disables the read and write cycles. Data can be sent in MSB- or in LSB-first mode. MSB first is the default setting on power-up and can be changed via the configuration register. For more information, see the AN-877 Application Note, Interfacing to High Speed ADCs via SPI. Table 13. Serial Port Interface Pins Pin SCLK SDIO CSB Function SCLK (serial clock) is the serial shift clock. SCLK synchronizes serial interface reads and writes. SDIO (serial data input/output) is an input and output depending on the instruction being sent and the relative position in the timing frame. CSB (chip select) is an active low control that gates the read and write cycles. Table 14. SPI Timing Diagram Specifications Parameter tSDS tSDH tSCLK tSS tSH tSHIGH The falling edge of CSB in conjunction with the rising edge of the SCLK determines the start of the framing. Figure 42 and Table 14 provide an example of the serial timing and its definitions. Definition Setup time between data and rising edge of SCLK Hold time between data and rising edge of SCLK Period of the clock Setup time between CSB and SCLK Hold time between CSB and SCLK Minimum period that SCLK should be in a logic high state Minimum period that SCLK should be in a logic low state tSLOW Other modes involving CSB are available. CSB can be held low indefinitely to permanently enable the device (this is called streaming). CSB can stall high between bytes to allow for tSHIGH tSDS tSS tSCLK tSH tSDH tSLOW CSB SCLK DON’T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 D5 D4 D3 D2 D1 D0 DON’T CARE 07773-036 SDIO DON’T CARE DON’T CARE Figure 42. Serial Port Interface Timing Diagram Rev. 0 | Page 19 of 24 AD9267 HARDWARE INTERFACE The pins described in Table 13 comprise the physical interface between the programming device of the user and the serial port of the AD9267. The SCLK and CSB pins function as inputs when using the SPI interface. The SDIO pin is bidirectional, functioning as an input during write phases and as an output during readback. The SPI interface is flexible enough to be controlled by either PROM or PIC microcontrollers. This provides the user with the ability to use an alternate method to program the ADC. One such method is described in detail in the AN-812 Application Note, MicroController-Based Serial Port Interface (SPI) Boot Circuit. When the SPI interface is not used, SCLK/PLLMULT0 and SDIO/PLLMULT1 serve a dual function. When strapped to AVDD or ground during device power-on, the pins are associated with a specific function. Rev. 0 | Page 20 of 24 AD9267 APPLICATIONS INFORMATION Depending on the application and the system architecture, this low order filter may or may not be necessary. The signal transfer function (STF) of a continuous time feedforward ADC usually contains out-of-band peaks. Because these STF peaks are typically one or two octaves above the pass-band edge, they are not problematic in applications where the bulk of the signal energy is in or near the pass band. However, in applications with large far-out interferers, it is necessary to either add a filter to attenuate these problematic signals or to allocate some of the ADC dynamic range to accommodate them. Figure 43 shows the normalized STF of the AD9267 CT Σ-Δ converter. The figure shows out-of-band peaking beyond the band edge of the ADC. Within the 10 MHz band of interest, the STF is maximally flat with less than 0.1 dB of gain. Maximum peaking occurs at 60 MHz with 10 dB of gain. To put this into perspective, for a fixed input power, a 5 MHz in-band-signal appears at −5 dBFS, a 25 MHz tone appears at −2 dBFS and 60 MHz tone at +5 dBFS. Because the maximum input to the ADC is −2 dBFS, large out-of-band signals can quickly saturate the system. This implies that under these conditions, the digital outputs of the ADC no longer accurately represents the input. Refer to the Overrange (OR) Condition section for details on overrange detection and recovery. 15 The noise performance is normalized to a −2 dBFS in-band signal. The AD9267 STF and NTF are flat within the band of interest and should result in almost no change in input level and IBN. Beyond the bandwidth of the AD9267, out-of-band peaking adds gain to the system, therefore requiring the input power to be scaled back to prevent in-band noise degradation. The input power is scaled back to a point where only 3 dB of noise degradation is allowed, therefore resulting in Figure 44. 5 0 –5 –40°C –10 CHEBYSHEV II FILTER RESPONSE –15 +85°C +25°C –20 –25 0 10 20 30 40 50 60 70 80 90 100 FREQUENCY (MHz) 07773-051 The need for anti-alias protection often requires one or two octaves for a transition band, which reduces the usable bandwidth of a Nyquist converter to between 25% and 50% of the available bandwidth. A CT Σ-Δ converter maximizes the available signal bandwidth by forgoing the need for an antialiasing filter because the architecture possesses inherent antialiasing. Although a high order, sharp cutoff antialiasing filter may not be necessary because of the unique characteristics of the architecture, a low order filter may still be required to precede the ADC for out-of-band signal handling. Figure 43 shows the gain profile of the AD9267 and this can be interpreted as the level in which the signal power should be scaled back to prevent an overload condition. This is the ultimate trip point and before this point is reached, the in-band noise (IBN) slowly degrades. As a result, it is recommended that the low-pass filter be designed to match the profile of Figure 44, which shows the maximum input signal for a 3 dB degradation of in-band noise. The input signal is attenuated to allow only 3 dB of noise degradation over frequency. AMPLITUDE (dB) FILTERING REQUIREMENT Figure 44. Maximum Input Level for 3 dB Noise Degradation An example third-order low-pass Chebyshev II type filter is shown in Figure 45 and the corresponding magnitude vs. frequency response of the filter is shown in Figure 44. L1 180nH 13 11 VIN+ C1 39pF 7 5 C2 390pF L1 180nH C3 220pF 1kΩ AD9267 CT Σ-Δ 1 C2 390pF –1 Figure 45. Third-Order Low-Pass Chebyshev II Filter –3 –5 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 90 100 Figure 43. STF Rev. 0 | Page 21 of 24 07773-052 VIN– 3 07773-049 GAIN (dB) 9 Parameter C1 L1 C2 C3 Value 39 180 390 220 Unit pF nH pF pF Manufacturer Murata GRM188 series, 0603 Coil Craft 0402AF, 2% Murata GRM188 series, 0603 Murata GRM188 series, 0603 40 –2 30 –4 20 –6 10 –8 0 –10 –10 –12 –20 –14 –30 –16 –40 –18 –50 –20 0 2 4 6 8 10 12 14 16 18 FREQUENCY (MHz) –60 20 GROUP DELAY (ns) Table 15. Chebyshev II Filter Components 0 07773-050 Referring to Figure 46, the 3 dB cutoff frequency of the lowpass Chebyshev II filter response resides at 15.75 MHz, and at 10 MHz, there is 0.43 dB of attenuation due to the sharp roll-off of the filter. Table 15 summarizes the components and manufacturers used to build the circuit. AMPLITUDE (dB) AD9267 Figure 46. Low-Pass Chebyshev II Filter Response In addition to matching the profile of Figure 44, group delay and channel matching are important filter design criteria. Low tolerance components are highly recommended for improved channel matching, which translates to minimal degradation in image rejection for quadrature systems. Rev. 0 | Page 22 of 24 AD9267 MEMORY MAP Table 16. Memory Map Register SPI Port Config Chip ID Chip Grade Channel Index Power Modes PLLENABLE PLL Output Modes Output Adjust Output Clock Reference Overrange Address (Hex) 00 01 02 05 08 09 0A 14 15 16 18 111 Bit 7 0 Bit 6 LSBFIRST Bit 5 SOFTRESET Bit 4 Bit 3 1 1 CHIPID[7:0] CHILDID[1:0] Bit 2 SOFTRESET Bit 1 LSBFIRST Bit 0 0 Channel[1:0] PWRDWN[1:0] PLLLOCKED DRVSTD PLLENABLE PLLMULT[5:0] PLLAUTO OUTENB LVDSTERM[1:0] DCOINV AUTORST EXTREF OR_IND1 OR_IND2 MEMORY MAP DEFINITIONS Table 17. Memory Map Definitions Register SPI Port Config Address 0x00 Bit Name LSBFIRST Bit(s) [6], [1] Default 0 Chip ID Chip Grade 0x01 0x02 SOFTRESET CHIPID CHILDID [5], [2] [7:0] 5:4] 0 0x22 0 Channel Index 0x05 Channel [1:0] 0 Power Modes 0x08 PWRDWN [1:0] 0 PLLENABLE PLL 0x09 0x0A PLLENABLE PLLLOCKED [2] [7] 0 0 PLLAUTO [6] 0 Output Modes 0x14 PLLMULT DRVSTD [5:0] [7] 0 0 Output Adjust 0x15 OUTENB LVDSTERM [4] [5:4] 0 0 Output Clock Reference Overrange 0x16 0x18 0x111 DCOINV EXTREF AUTORST OR_IND1 OR_IND2 [7] [6] [7] [6] [5] 0 0 0 0 0 Rev. 0 | Page 23 of 24 Description 0: serial interface uses MSB-first format 1: serial interface uses LSB-first format 1: default all serial registers except 0x00, 0x09, and 0x0A 0x22: AD9267 0x00: 10 MHz bandwidth 0x10: 5 MHz bandwidth 0x20: 2.5 MHz bandwidth 0x30: modulator only 0x1: Channel A only addressed 0x2: Channel B only addressed 0x3: both channels addressed simultaneously 0x0: normal operation 0x1: channel power-down (local) 0x2: standby (everything except reference circuits) 0x3: sleep 1: enable PLL 0: PLL is not locked 1: PLL is locked 0: disable PLL auto band select 1: enable PLL auto band select See Table 8 0: ANSI-644 1: Low power (IEEE1596.3 similar) 1: Channel A and Channel B outputs tristated 0: no termination 1: 200 Ω 2: 100 Ω 3: 100 Ω 1: invert DCO± 1: use external reference 1: enable autoreset See Table 12 See Table 12 AD9267 OUTLINE DIMENSIONS 0.60 MAX 9.00 BSC SQ 0.60 MAX 64 49 48 PIN 1 INDICATOR 1 PIN 1 INDICATOR 8.75 BSC SQ 0.50 BSC 0.50 0.40 0.30 1.00 0.85 0.80 SEATING PLANE 33 32 16 17 0.25 MIN 7.50 REF 0.80 MAX 0.65 TYP 12° MAX 0.05 MAX 0.02 NOM 0.30 0.23 0.18 6.35 6.20 SQ 6.05 EXPOSED PAD (BOTTOM VIEW) 0.20 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4 091707-C TOP VIEW Figure 47. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 9 mm × 9 mm Body, Very Thin Quad Dimensions shown in millimeters ORDERING GUIDE Model AD9267BCPZ1 AD9267EBZ1 1 Temperature Range −40°C to +85°C Package Description 64-Lead Lead Frame Chip Scale Package (LFCSP_VQ) Evaluation Board Z = RoHs Compliant Part. ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07773-0-7/09(0) Rev. 0 | Page 24 of 24 Package Option CP-64-4