LT1585-1.5/LT1585A-1.5 Fixed 1.5V, 4.6A and 5A Low Dropout, Fast Response GTL+ Regulators DESCRIPTIO U FEATURES ■ ■ ■ ■ ■ The LT ®1585-1.5/LT1585A-1.5 are low dropout, 3-terminal regulators with 4.6A and 5A output current capability respectively, and a fixed 1.5V output voltage. The designs are optimized for low voltage applications where transient response and minimum input voltage are critical. Similar to the LT1084, they have lower dropout and faster transient response. These improvements make them ideal for low voltage microprocessor applications, especially as the regulator in an Intel processor GTL+ supply. Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation: 0.05% Typ Trimmed Current Limit On-Chip Thermal Limiting U APPLICATIO S ■ ■ ■ GTL+ Power Supply Low Voltage Logic Supplies Battery-Powered Circuitry Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that creates excessive junction temperatures. The LT1585-1.5/LT1585A-1.5 are available in the throughhole 3-pin TO-220 power package and 3-pin plastic DD. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO Intel Processor GTL+ Supply LT1585A-1.5 VIN VOUT 3.3V VTT = 1.5V 5A C7 TO C12 1µF GND + C1, C2 100µF 10V + C3 TO C6 100µF 10V R1 75Ω R2 150Ω R5 100Ω VREF R7 100Ω R8 100Ω R6 100Ω VREF C13 0.1µF R4 150Ω Q1 Q2 RX NOTE: LTC RECOMMENDS CENTRALLY LOCATING THE LT1585A-1.5 TO MINIMIZE VTT DISTRIBUTION DROPS AND USING SEPARATE VREF GENERATORS AT EACH BUS END TX C14 0.1µF RX RX TX R3 75Ω TX RX Q3 • • • 142 TOTAL SIGNAL LINES Q4 TX 1585-1.5 • TA01 1 LT1585-1.5/LT1585A-1.5 W W U W ABSOLUTE MAXIMUM RATINGS (Note 1) Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C UU U VIN ............................................................................ 7V Operating Junction Temperature Range Control Section .................................. 0°C to 125°C Power Transistor ................................ 0°C to 150°C PRECONDITIONI G 100% Thermal Limit Functional Test W U U PACKAGE/ORDER INFORMATION FRONT VIEW TAB IS OUTPUT 3 VIN 2 VOUT 1 M PACKAGE 3-LEAD PLASTIC DD θJA = 30°C/W* GND *WITH PACKAGE SOLDERED TO 0.5 SQUARE INCH COPPER AREA OVER BACKSIDE GROUND PLANE OR INTERNAL POWER PLANE. θJA CAN VARY FROM 20°C/W TO > 40°C/W WITH OTHER MOUNTING TECHNIQUES ORDER PART NUMBER FRONT VIEW LT1585CM-1.5 LT1585ACM-1.5 TAB IS OUTPUT 3 VIN 2 VOUT 1 GND ORDER PART NUMBER LT1585CT-1.5 LT1585ACT-1.5 T PACKAGE 3-LEAD PLASTIC TO-220 θJA = 50°C/W Consult factory for Industrial and Military grade parts. ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the specified operating temperature range, otherwise specifications are at TA = 25°C. PARAMETER CONDITIONS Output Voltage (Note 4) VIN = 5V, TJ = 25°C, IOUT = 0mA 3V ≤ VIN ≤ 7V, 0mA ≤ IOUT ≤ IFULL LOAD ● Line Regulation (Notes 2, 3) 3V ≤ VIN ≤ 7V, IOUT = 0mA Load Regulation (Notes 2, 3, 4) VIN = 5V, TJ = 25°C, 0mA ≤ IOUT ≤ IFULL LOAD Dropout Voltage (Note 4) ∆VOUT = 1%, IOUT = IFULL LOAD ● Current Limit LT1585-1.5, (VIN – VOUT) = 5.5V LT1585A-1.5, (VIN – VOUT) = 5.5V ● ● Quiescent Current VIN = 5V ● Ripple Rejection (Note 4) f = 120Hz, COUT = 25µF Tant., VIN = 4.5V, IOUT = IFULL LOAD ● Thermal Regulation TA = 25°C, 30ms Pulse MIN TYP MAX 1.485 (– 1%) 1.470 (– 2%) 1.5 1.5 1.515 (+ 1%) 1.530 (+ 2%) V V 0.005 0.2 % 0.05 0.05 0.3 0.5 % % 1.200 1.400 V ● 4.60 5.00 5.25 6.00 7 60 Temperature Stability ● TA = 125°C, 1000 Hrs. 0.03 RMS Output Noise (% of VOUT) TA = 25°C, 10Hz ≤ f ≤ 10kHz 0.003 Thermal Resistance Junction to Case T Package: Control Circuitry/Power Transistor M Package: Control Circuitry/Power Transistor 2 13 mA dB 0.02 0.5 Long-Term Stability Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note 2: See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are measured at a constant junction temperature by low duty cycle pulse testing. Note 3: Line and load regulation are guaranteed up to the maximum power dissipation (25W for the LT1585-1.5 in T package and 27.5W for A A 72 0.004 UNITS %/W % 1.0 % % 0.7/3.0 0.7/3.0 °C/W °C/W the LT1585A-1.5). Power dissipation is determined by input/output differential and the output current. Guaranteed maximum output power will not be available over the full input/output voltage range. Note 4: IFULL LOAD is defined as the maximum value of output load current as a function of input-to-output voltage. IFULL LOAD is equal to 4.6A for the LT1585-1.5 and 5A for the LT1585A-1.5. The LT1585-1.5/LT1585A-1.5 have constant current limit with changes in input-to-output voltage. LT1585-1.5/LT1585A-1.5 U W TYPICAL PERFORMANCE CHARACTERISTICS LT1585A-1.5 Dropout Voltage vs Output Current LT1585A-1.5 Short-Circuit Current vs Temperature T = –5°C 1.2 1.1 T = 125°C 1.0 T = 25°C 0.9 0.8 0.7 OUTPUT VOLTAGE DEVIATION (%) 1.3 SHORT-CIRCUIT CURRENT (A) GUARANTEED TEST POINTS 1.4 5.5 5.0 4.5 ∆I = IFULL LOAD 0.05 0 –0.05 –0.10 –0.15 0.6 3 4 2 OUTPUT CURRENT (A) 5 4.0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) –0.20 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 1585-1.5 G03 1585-1.5 G02 1585-1.5 G01 Output Voltage vs Temperature Quiescent Current vs Temperature 1.53 13 12 1.52 QUIESCENT CURRENT (mA) 1 1.51 1.50 1.49 1.48 11 10 9 8 7 6 5 4 1.47 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 1585-1.5 G04 1585-1.5 G05 Ripple Rejection vs Frequency Maximum Power Dissipation* 90 30 LT1585A-1.5 80 25 70 60 20 POWER (W) 0 OUTPUT VOLTAGE (V) 0.5 RIPPLE REJECTION (dB) DROPOUT VOLTAGE (V) Load Regulation vs Temperature 0.10 6.0 1.5 50 40 30 LT1585-1.5 15 10 20 (VIN – VOUT) ≤ 3V 0.5V ≤ VRIPPLE ≤ 2V IOUT = IFULL LOAD 10 5 0 10 100 1k 10k FREQUENCY (Hz) 100k 1585-1.5 G06 0 50 60 70 80 90 100 110 120 130 140 150 CASE TEMPERATURE (˚C) 1585-1.5 G07 *AS LIMITED BY MAXIMUM JUNCTION TEMPERATURE 3 LT1585-1.5/LT1585A-1.5 W W SI PLIFIED SCHE ATIC VIN + – THERMAL LIMIT VOUT GND 1585-1.5 SS U W U U APPLICATIONS INFORMATION General The LT1585-1.5/LT1585A-1.5 3-terminal regulators are easy to use and have all the protection features expected in high performance linear regulators. The devices are short-circuit protected, safe-area protected and provide thermal shutdown to turn off the regulators if the junction temperature exceeds about 150°C. The ICs are pin compatible with the LT1083/LT1084/LT1085 family of linear regulators but offer lower dropout voltage and faster transient response. The trade-off for this improved performance is a 7V maximum supply voltage. Similar to the LT1083/LT1084/LT1085 family, the LT15851.5/LT1585A-1.5 regulators require an output capacitor for stability. However, the improved frequency compensation permits the use of capacitors with much lower ESR while still maintaining stability. This is critical in addressing the needs of modern low voltage, high speed microprocessors. Current generation microprocessors and their associated circuitry cycle load current from almost zero to several amps in tens of nanoseconds. Output voltage tolerances are tighter and include transient response as part of the specification. The LT1585-1.5/LT1585A-1.5 are specifically designed to meet the fast current load step require- 4 ments of these applications and save total cost by needing less output capacitance in order to maintain regulation. Stability The circuit design in the LT1585-1.5/LT1585A-1.5 requires the use of an output capacitor as part of the frequency compensation. For all operating conditions, the addition of a 22µF solid tantalum or a 100µF aluminum electrolytic on the output ensures stability. Normally, the LT1585-1.5/LT1585A-1.5 can use smaller value capacitors. Many different types of capacitors are available and have widely varying characteristics. These capacitors differ in capacitor tolerance (sometimes ranging up to ±100%), equivalent series resistance, equivalent series inductance and capacitance temperature coefficient. The LT1585-1.5/ LT1585A-1.5 frequency compensation optimizes frequency response with low ESR capacitors. In general, use capacitors with an ESR of less than 1Ω. Normally, capacitor values on the order of several hundred microfarads are used on the output of the regulators to ensure good transient response with heavy load current changes. Output capacitance can increase without limit and larger values of output capacitance further improve the LT1585-1.5/LT1585A-1.5 U W U U APPLICATIONS INFORMATION stability and transient response of the LT1585-1.5/ LT1585A-1.5. Large load current changes are exactly the situation presented by modern microprocessors and their peripheral circuitry. The load current step contains higher order frequency components that the output decoupling network must handle until the regulator throttles to the load current level. Capacitors are not ideal elements and contain parasitic resistance and inductance. These parasitic elements dominate the change in output voltage at the beginning of a transient load step change. The ESR of the output capacitors produces an instantaneous step in output voltage [∆V = ∆I(ESR)]. The ESL of the output capacitors produces a droop proportional to the rate of change of output current [V = L(∆I/∆t)]. The output capacitance produces a change in output voltage proportional to the time until the regulator can respond [∆V = ∆t(∆I/C)]. These transient effects are illustrated in Figure 1. ESR EFFECTS ESL EFFECTS CAPACITANCE EFFECTS 1585-1.5 F01 SLOPE, V ∆I = t C POINT AT WHICH REGULATOR TAKES CONTROL range of input supply voltage. The lower current limit rating and 7V maximum supply voltage rating for this device permit this characteristic. Current limit oscillations are typically nonexistent unless the input and output decoupling capacitors for the regulators are mounted several inches from the terminals. Protection Diodes In normal operation, the LT1585-1.5/LT1585A-1.5 do not require any protection diodes. Older 3-terminal regulators require protection diodes between the output pin and the input pin to prevent die overstress. A protection diode between the input and output pins is usually not needed. An internal diode between the input and output pins on the LT1585-1.5/LT1585A-1.5 can handle microsecond surge currents of 50A to 100A. Even with large value output capacitors it is difficult to obtain those values of surge currents in normal operation. Only with large values of output capacitance, such as 1000µF to 5000µF, and with the input pin instantaneously shorted to ground can damage occur. A crowbar circuit at the input of the LT1585-1.5/LT1585A-1.5 can generate those levels of current and a diode from output to input is then recommended. This is shown in Figure 2. Usually, normal power supply cycling or system “hot plugging and unplugging” will not generate current large enough to do any damage. Figure 1 The use of capacitors with low ESR, low ESL and good high frequency characteristics is critical in meeting the output voltage tolerances of these high speed microprocessor applications. These requirements dictate a combination of high quality surface mount tantalum capacitors and ceramic capacitors. The location of the decoupling network is critical to transient response performance. Place the decoupling network as close as possible to the microprocessor control circuitry because a trace run from the decoupling capacitors to the actual circuitry is inductive. In addition, use large power and ground plane areas to minimize distribution drops. A possible stability problem that occurs in monolithic linear regulators is current limit oscillations. The LT1585-1.5/ LT1585A-1.5 essentially have a flat current limit over the D1 1N4002 (OPTIONAL) VIN + IN C1 10µF LT1585-1.5 OUT GND + VOUT C2 10µF 1585-1.5 F02 Figure 2 Ripple Rejection The typical curve for ripple rejection reflects values for the LT1585-1.5/LT1585A-1.5 as a function of frequency. In applications that require improved ripple rejection, use the adjustable LT1585/LT1585A. A bypass capacitor from the adjust pin to ground reduces the output ripple by the ratio of VOUT/1.25V. 5 LT1585-1.5/LT1585A-1.5 U W U U APPLICATIONS INFORMATION Load Regulation It is not possible to provide true remote load sensing because the LT1585-1.5/LT1585A-1.5 are 3-terminal devices. Load regulation is limited by the resistance of the wire connecting the regulators to the load. Load regulation per the data sheet specification is measured at the bottom of the package. For fixed voltage devices, negative side sensing is a true Kelvin connection with the GND pin of the device returned to the negative side of the load. This is illustrated in Figure 3. VIN IN LT1585-1.5 OUT RP PARASITIC LINE RESISTANCE Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly below the die. This is the lowest resistance path for heat flow. Proper mounting ensures the best thermal flow from this area of the package to the heat sink. Linear Technology strongly recommends thermal compound at the case-to-heat sink interface. Use a thermally conductive spacer if the case of the device must be electrically isolated and include its contribution to the total thermal resistance. Please consult “Mounting Considerations for Power Semiconductors” 1990 Linear Applications Handbook, Volume I, Pages RR3-1 to RR3-20. The output connects to the case of the device in the LT1585-1.5/LT1585A-1.5. For example, using an LT1585ACT-1.5 (TO-220, commercial) and assuming: GND RL 1585-1.5 F03 Figure 3. Connection for Best Load Regulation VIN (Max Continuous) = 3.465V (3.3V + 5%), VOUT = 1.5V IOUT = 5A TA = 70°C, θHEAT SINK = 3°C/W θCASE-TO-HEAT SINK = 1°C/W (with Thermal Compound) Power dissipation under these conditions is equal to: Thermal Considerations The LT1585-1.5/LT1585A-1.5 protect the device under overload conditions with internal power and thermal limiting circuitry. However, for normal continuous load conditions, do not exceed maximum junction temperature ratings. It is important to consider all sources of thermal resistance from junction-to-ambient. These sources include the junction-to-case resistance, the case-to-heat sink interface resistance, and the heat sink resistance. Thermal resistance specifications have been developed to more accurately reflect device temperature and ensure safe operating temperatures. The electrical characteristics section provides a separate thermal resistance and maximum junction temperature for both the control circuitry and the power transistor. Older regulators with a single junctionto-case thermal resistance specification, use an average of the two values provided here and allow excessive junction temperatures under certain conditions of ambient temperature and heat sink resistance. Calculate the maximum junction temperature for both sections to ensure that both thermal limits are met. 6 PD = (VIN – VOUT)(IOUT) = (3.465 – 1.5)(5A) = 9.825W Junction temperature will be equal to: TJ = TA + PD(θHEAT SINK + θCASE-TO-HEAT SINK + θJC) For the Control Section: TJ = 70°C + 9.825W (3°C/W + 1°C/W + 0.7°C/W) = 116.2°C 116.2°C < 125°C = TJMAX (Control Section Commercial Range) For the Power Transistor: TJ = 70°C + 9.825W (3°C/W + 1°C/W + 3°C/W) = 138.8°C 138.8°C < 150°C = TJMAX (Power Transistor Commercial Range) In both cases the junction temperature is below the maximum rating for the respective sections, ensuring reliable operation. LT1585-1.5/LT1585A-1.5 U PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted. M Package 3-Lead Plastic DD Pak (LTC DWG # 05-08-1460) 0.256 (6.502) 0.060 (1.524) TYP 0.060 (1.524) 0.390 – 0.415 (9.906 – 10.541) 0.165 – 0.180 (4.191 – 4.572) 0.045 – 0.055 (1.143 – 1.397) 15° TYP 0.060 (1.524) 0.183 (4.648) 0.059 (1.499) TYP 0.330 – 0.370 (8.382 – 9.398) ( +0.008 0.004 –0.004 +0.203 0.102 –0.102 ) 0.095 – 0.115 (2.413 – 2.921) 0.075 (1.905) 0.300 (7.620) ( +0.305 3.632 –0.508 BOTTOM VIEW OF DD PAK HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK 0.090 – 0.110 (2.286 – 2.794) +0.012 0.143 – 0.020 ) 0.050 (1.270) BSC 0.013 – 0.023 (0.330 – 0.584) 0.050 ± 0.012 (1.270 ± 0.305) M (DD3) 1098 T Package 3-Lead Plastic TO-220 (LTC DWG # 05-08-1420) 0.147 – 0.155 (3.734 – 3.937) DIA 0.390 – 0.415 (9.906 – 10.541) 0.165 – 0.180 (4.191 – 4.572) 0.045 – 0.055 (1.143 – 1.397) 0.230 – 0.270 (5.842 – 6.858) 0.460 – 0.500 (11.684 – 12.700) 0.570 – 0.620 (14.478 – 15.748) 0.330 – 0.370 (8.382 – 9.398) 0.980 – 1.070 (24.892 – 27.178) 0.520 – 0.570 (13.208 – 14.478) 0.100 (2.540) BSC 0.218 – 0.252 (5.537 – 6.401) 0.013 – 0.023 (0.330 – 0.584) 0.028 – 0.038 (0.711 – 0.965) 0.050 (1.270) TYP Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 0.095 – 0.115 (2.413 – 2.921) T3 (TO-220) 1098 7 LT1585-1.5/LT1585A-1.5 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC ® 1392 Micropower Temperature, Power Supply and Differential Voltage Monitor Micropower Data Acquisition to Monitor System LTC1530 High Power Step-Down Synchronous DC/DC Controller in SO-8 Synchronous Operation Up to 15A, Fixed or Adj Outputs LT1528 Low Dropout 3A Linear Regulator 0.6V Dropout for 5V to 4V Regulation LT1573 Low Dropout Regulator Driver Drives Low Cost PNP, Fast Transient Response TM LT1575 Ultrafast Transient Response Low Dropout Regulator Driver Drives N-Channel MOSFET Up to 10A, SO-8 LT1580 Very Low Dropout 7A Linear Regulator 0.54V Dropout at 7A, Fixed 2.5VOUT or Adjustable Ultrafast is a trademark of Linear Technology Corporation. 8 Linear Technology Corporation 158515fa LT/TP 0100 2K REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com LINEAR TECHNOLOGY CORPORATION 1996