CS5207−2
7.0 A, 1.5 V Fixed Linear
Regulator
The CS5207−2 provides 7.0 A at 1.5 V with an accuracy of ±2.0 %.
The regulator is intended for use as an active termination for the
GTL bus on Intel based motherboards. The fast loop response and low
dropout voltage make these regulators ideal for applications where
low voltage operation and good transient response are important.
The circuit is designed to operate with dropout voltages as low as 1.0 V
depending on the output current level. The maximum quiescent current is
only 10 mA at full load.
The regulators are fully protected against overload conditions with
protection circuitry for Safe Operating Area (SOA), overcurrent and
thermal shutdown.
The CS5207−2 is available in TO−220 packages.
TO−220
THREE LEAD
T SUFFIX
CASE 221A
1
Features
• Output Current to 7.0 A
• Output Voltage Trimmed to ±2.0%
• Dropout Voltage 1.45 V @ 7.0 A
• Fast Transient Response
• Fault Protection Circuitry
− Thermal Shutdown
− Overcurrent Protection
− Safe Area Protection
2
3
PIN CONNECTIONS AND
MARKING DIAGRAMS
CS5207−2
AWLYWW
VOUT
VIN
Tab = VOUT
Pin 1. GND
2. VOUT
3. VIN
1
A
WL, L
YY, Y
WW, W
Output
Current
Limit
Thermal
Shutdown
http://onsemi.com
= Assembly Location
= Wafer Lot
= Year
= Work Week
ORDERING INFORMATION*
− + Error
Amplifier
Device
CS5207−2GT3
Bandgap
GND
Package
Shipping
TO−220†
50 Units/Rail
*Additional ordering information can be found on page
5 of this data sheet.
† TO−220 is 3−pin, straight leaded.
Figure 1. Block Diagram
© Semiconductor Components Industries, LLC, 2006
September, 2006 − Rev. 8
1
Publication Order Number:
CS5207−2/D
CS5207−2
MAXIMUM RATINGS*
Parameter
Supply Voltage, VCC
Operating Temperature Range
Junction Temperature
Storage Temperature Range
Lead Temperature Soldering:
Wave Solder (through hole styles only) Note 1
ESD Damage Threshold
Value
Unit
17
V
−40 to +70
°C
150
°C
−60 to +150
°C
260 Peak
°C
2.0
kV
1. 10 second maximum.
*The maximum package power dissipation must be observed.
ELECTRICAL CHARACTERISTICS (CIN = 10 μF, COUT = 22 μF Tantalum, VIN − VOUT = 3.0 V, VIN ≤ 10 V, 0°C ≤ TA ≤ 70°C,
TJ ≤ +150°C, unless otherwise specified, Ifull load = 7.0 A)
Test Conditions
Characteristic
Min
Typ
Max
Unit
1.47
(−2.0%)
1.50
1.53
(+2.0%)
V
Fixed Output Voltage
Output Voltage (Notes 2 and 3)
VIN − VOUT = 1.65 V;
0 ≤ IOUT ≤ 7.0 A
Line Regulation
1.65 V ≤ VIN − VOUT ≤ 6.0 V; IOUT = 10 mA
−
0.04
0.20
%
Load Regulation (Notes 2 and 3)
VIN − VOUT = 1.65 V; 10 mA ≤ IOUT ≤ 7.0 A
−
0.08
0.40
%
Dropout Voltage (Note 4)
IOUT = 7.0 A
−
1.42
1.65
V
Current Limit
VIN − VOUT = 3.0 V; TJ ≥ 25°C
VIN − VOUT = 12 V
7.1
−
8.5
1.0
−
−
A
A
Quiescent Current
VIN ≤ 9.0 V; IOUT = 10 mA
−
5.0
10
mA
Thermal Regulation
30 ms Pulse, TA = 25°C
−
0.003
−
%/W
Ripple Rejection
f = 120 Hz; IOUT = 7.0 A
−
80
−
dB
−
−
0.5
−
%
−
0.003
−
%/VOUT
Temperature Stability
RMS Output Noise (%VOUT)
10 Hz ≤ f ≤ 10 kHz
Thermal Shutdown
−
150
180
−
°C
Thermal Shutdown Hysteresis
−
−
25
−
°C
2. Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output
voltage due to thermal gradients or temperature changes must be taken into account seperately.
3. Specifications apply for an external Kelvin sense connection at a point on the output pin 1/4” from the bottom of the package.
4. Dropout voltage is a measurement of the minimum input/output differential at full load.
PACKAGE PIN DESCRIPTION
Package Pin Number
TO−220
Pin Symbol
1
GND
Ground connection.
2
VOUT
Regulated output voltage (case).
3
VIN
Function
Input voltage.
http://onsemi.com
2
CS5207−2
1.55
1.50
1.45
1.40
1.35
1.30
1.25
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.10
0.08
Output Voltage Deviation (%)
Dropout Voltage (V)
TYPICAL PERFORMANCE CHARACTERISTICS
TCASE = 0°C
TCASE = 25°C
TCASE = 125°C
0.06
0.04
0.02
0.00
−0.02
−0.04
−0.06
−0.08
−0.10
0
1
2
3
4
5
6
−0.12
7
Figure 2. Dropout Voltage vs. Output
Current
Figure 3. Output Voltage vs. Temperature
100
90
0.175
TCASE = 125°C
80
0.150
Ripple Rejection (dB)
Output Voltage Deviation (%)
10 20 30 40 50 60 70 80 90 100 110 120 130
TJ (°C)
0.200
0.125
TCASE = 25°C
0.100
0.075
0.050
70
60
50
40
30
20
TCASE = 0°C
0.025
0.000
0
Output Current (A)
TCASE = 25°C
IOUT = 7.0 A
(VIN − VOUT) = 3.0 V
VRIPPLE = 1.6 VPP
10
0
1
2
3
4
5
6
0
101
7
102
103
104
Frequency (Hz)
Output Current (A)
Figure 4. Load Regulation vs.
Output Current
Figure 5. Ripple Rejection vs. Frequency
http://onsemi.com
3
105
CS5207−2
APPLICATIONS INFORMATION
Protection Diodes
The CS5207−2 linear regulator provides a fixed 1.5 V
output at currents up to 7.0 A. The regulator is protected
against short circuit, and includes thermal shutdown and
safe area protection (SOA) circuitry. The SOA protection
circuitry decreases the maximum available output current as
the input−output differential voltage increase.
The CS5207−2 has a composite PNP−NPN output
transistor and requires an output capacitor for stability. A
detailed procedure for selecting this capacitor is included in
the Stability Considerations section.
When large external capacitors are used with a linear
regulator it is sometimes necessary to add protection diodes.
If the input voltage of the regulator gets shorted, the output
capacitor will discharge into the output of the regulator. The
discharge current depends on the value of the capacitor, the
output voltage and the rate at which VIN drops. In the
CS5207−2 linear regulator, the discharge path is through a
large junction and protection diodes are not usually needed.
If the regulator is used with large values of output
capacitance and the input voltage is instantaneously shorted
to ground, damage can occur. In this case, a diode connected
as shown in Figure 6 is recommended.
Stability Considerations
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start−up
delay, load transient response, and loop stability.
The capacitor value and type is based on cost, availability,
size and temperature constraints. A tantalum or aluminum
electrolytic capacitor is best, since a film or ceramic
capacitor with almost zero ESR can cause instability. The
aluminum electrolytic capacitor is the least expensive
solution. However, when the circuit operates at low
temperatures, both the value and ESR of the capacitor will
vary considerably. The capacitor manufacturer’s data sheet
provides this information.
A 22 μF tantalum capacitor will work for most
applications, but with high current regulators such as the
CS5207−2 the transient response and stability improve with
higher values of capacitance. The majority of applications
for this regulator involve large changes in load current so the
output capacitor must supply the instantaneous load current.
The ESR of the output capacitor causes an immediate drop
in output voltage given by:
DV + DI
IN4002 (Optional)
VIN
VIN
C1
VOUT
CS5207−2
VOUT
C2
GND
Figure 6. Protection Diode Scheme for Fixed
Output Regulators
Output Voltage Sensing
Since the CS5207−2 is a three terminal regulator, it is not
possible to provide true remote load sensing. Load
regulation is limited by the resistance of the conductors
connecting the regulator to the load. For best results the
regulator should be connected as shown in Figure 7.
ESR
For microprocessor applications it is customary to use an
output capacitor network consisting of several tantalum and
ceramic capacitors in parallel. This reduces the overall ESR
and reduces the instantaneous output voltage drop under
transient load conditions. The output capacitor network
should be as close to the load as possible for the best results.
VIN
VIN
VOUT
RC
Conductor Parasitic
Resistance
CS5207−2
RLOAD
Figure 7. Conductor Parasitic Resistance Effects
Can Be Minimized With the Above Grounding
Scheme for Fixed Output Regulators
http://onsemi.com
4
CS5207−2
Calculating Power Dissipation and Heat Sink
Requirements
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment has a thermal resistance. Like series
electrical resistances, these resistances are summed to
determine RΘJA, the total thermal resistance between the
junction and the surrounding air.
1. Thermal Resistance of the junction to case, RΘJC
(°C/W)
2. Thermal Resistance of the case to Heat Sink, RΘCS
(°C/W)
3. Thermal Resistance of the Heat Sink to the ambient
air, RΘSA (°C/W)
These are connected by the equation:
The CS5207−2 includes thermal shutdown and safe
operating area circuitry to protect the device. High power
regulators such as these usually operate at high junction
temperatures so it is important to calculate the power
dissipation and junction temperatures accurately to ensure
that an adequate heat sink is used.
The case is connected to VOUT on the CS5207−2,
electrical isolation may be required for some applications.
Thermal compound should always be used with high current
regulators such as these.
The thermal characteristics of an IC depend on the
following four factors:
1.
2.
3.
4.
Maximum Ambient Temperature TA (°C)
Power dissipation PD (Watts)
Maximum junction temperature TJ (°C)
Thermal resistance junction to ambient RΘJA (°C/W)
RQJA + RQJC ) RQCS ) RQSA
The value for RΘJA is calculated using equation (3) and
the result can be substituted in equation (1).
RΘJC is 1.6°C/Watt for the CS5207−2. For a high current
regulator such as the CS5207−2 the majority of the heat is
generated in the power transistor section. The value for
RΘSA depends on the heat sink type, while RΘCS depends on
factors such as package type, heat sink interface (is an
insulator and thermal grease used?), and the contact area
between the heat sink and the package. Once these
calculations are complete, the maximum permissible value
of RΘJA can be calculated and the proper heat sink selected.
For further discussion on heat sink selection, see application
note “Thermal Management,” document number
AND8036/D, available through the Literature Distribution
Center or via our website at http://onsemi.com.
These four are related by the equation
TJ + TA ) PD
RQJA
(1)
The maximum ambient temperature and the power
dissipation are determined by the design while the
maximum junction temperature and the thermal resistance
depend on the manufacturer and the package type.
The maximum power dissipation for a regulator is:
PD(max) + {VIN(max) * VOUT(min)}IOUT(max) ) VIN(max)IQ
(2)
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current, for the
application
IQ is the maximum quiescent current at IOUT(max).
ADDITIONAL ORDERING INFORMATION
Orderable Part
Number
CS5207−2GT3
(3)
Type
Description
7.0 A, 1.5 V Output
TO−220 THREE LEAD, STRAIGHT
http://onsemi.com
5
CS5207−2
PACKAGE DIMENSIONS
TO−220
THREE LEAD
T SUFFIX
CASE 221A−08
ISSUE AA
−T−
F
−B−
4
Q
C
T
S
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
A
U
1 2 3
−Y−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
H
K
L
R
V
G
J
N
D 3 PL
0.25 (0.010)
M
B
M
INCHES
MIN
MAX
0.560
0.625
0.380
0.420
0.140
0.190
0.025
0.035
0.139
0.155
0.100 BSC
−−−
0.280
0.012
0.045
0.500
0.580
0.045
0.060
0.200 BSC
0.100
0.135
0.080
0.115
0.020
0.055
0.235
0.255
0.000
0.050
0.045
−−−
MILLIMETERS
MIN
MAX
14.23
15.87
9.66
10.66
3.56
4.82
0.64
0.89
3.53
3.93
2.54 BSC
−−−
7.11
0.31
1.14
12.70
14.73
1.15
1.52
5.08 BSC
2.54
3.42
2.04
2.92
0.51
1.39
5.97
6.47
0.00
1.27
1.15
−−−
Y
PACKAGE THERMAL DATA
Parameter
TO−220
THREE LEAD
Unit
RΘJC
Typical
1.6
°C/W
RΘJA
Typical
50
°C/W
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CS5207−2/D