19-0372; Rev 4; 10/97 KIT ATION EVALU E L B A AVAIL Isolated Transformer Driver for PCMCIA Applications ____________________________Features ♦ Transformer Driver for Ultra-Thin 5V-µs Transformers The MAX845 consists of an oscillator followed by a toggle flip-flop. The flip-flop generates two 50% duty-cycle square waves, which are complementary at half the oscillator frequency (450kHz, min). These two signals drive the ground-referenced N-channel power switches. Internal circuitry ensures break-before-make action between the two switches. A low-power shutdown disables both the switches and the oscillator, reducing power consumption. An evaluation kit (MAX845EVKIT-MM) is available to evaluate lowprofile 5V 40mA and 5V 100mA applications. ________________________Applications ♦ Isolated DC-to-DC Power Supply for PCMCIA Applications ♦ 450kHz Minimum Switching Frequency ♦ Ultra-Low Input Supply Current Ripple ♦ Single +5V or +3.3V Supply ♦ 5µW Low-Power Shutdown Mode ♦ 8-Pin SO and µMAX Packages ♦ Low Output Ripple Permits Miniature Output Capacitors _______________Ordering Information PCMCIA Modem Cards PART Isolated Data Acquisition Isolated Interface Power Supply Noise-Immunity Communications Interface Bridging Ground Differences TEMP. RANGE PIN-PACKAGE MAX845C/D 0°C to +70°C Dice* MAX845ESA -40°C to +85°C 8 SO MAX845EUA -40°C to +85°C 8 µMAX *Contact factory for dice specifications. Medical Equipment Process Control Low-Power LAN Networks __________Typical Operating Circuit VIN ON / OFF 4 6 SD VCC D1 5V TOP VIEW C1 CR1 1 OUTPUT 5V @ 150mA C2 MAX845 3 FREQUENCY SELECT FS D2 GND1 GND2 2 7 ___________________Pin Configuration D1 1 GND1 2 FS 3 8 MAX845 SD 4 T1 C3 8 D2 7 GND2 6 VCC 5 N.C. SO/µMAX CR2 ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. MAX845 _______________General Description The MAX845 provides an isolated power supply small enough to fit in thin PCMCIA cards and space-sensitive applications. It drives a low-profile center-tapped transformer primary from a 5V or 3.3V DC power supply. The secondary can be wound to provide any isolated positive or negative voltage at powers up to 750mW. MAX845 Isolated Transformer Driver for PCMCIA Applications ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC) ...............................................-0.3V to +7V Control Input Voltage (SD, FS) ...................-0.3V to (VCC + 0.3V) Peak Output Switch Current (D1, D2) ......................................1A Output Switch Voltage (D1, D2) .............................................12V Average Output Switch Current (D1, D2) .........................200mA Continuous Power Dissipation (TA = +70°C) SO (derate 5.88mW/°C above +70°C) .........................471mW µMAX (derate 4.10mW/°C above +70°C) ....................330mW Operating Temperature Range ...........................-40°C to +85°C Storage Temperature Range .............................-65°C to +160°C Junction Temperature ......................................................+150°C Lead Temperature (soldering, 10sec) .............................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 5V ±10%, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER Switch On-Resistance Switch Frequency CONDITIONS MIN TYP FS = VCC = 4.5V 450 FS = VCC = 5.5V 550 860 1100 D1, D2; 100mA MAX UNITS 1.5 4.0 Ω 675 900 FS = 0V, VCC = 4.5V 500 FS = 0V, VCC = 5.5V 575 Operating Supply Current (Note 1) No load, SD = 0V, FS = VCC 1.1 Shutdown Supply Current (Note 2) SD = VCC Shutdown Input Threshold High 0.4 Low 0.8 FS Input Current Minimum Start-Up Voltage 10 High Low 0.8 FS = 0V 50 10 2.5 2.2 Note 1: Operating supply current is the current used by the MAX845 only. Load current is not included. Note 2: Shutdown supply current includes output switch leakage currents. 2 _______________________________________________________________________________________ V pA 2.4 FS = VCC mA µA 2.4 Shutdown Input Leakage Current FS Input Threshold 5.0 kHz V µA V Isolated Transformer Driver for PCMCIA Applications 30 25 VIN = 5.5V 15 6.5 6.0 5.5 5.0 4.5 4.0 3.5 40 60 80 -40 100 -20 0 TEMPERATURE (°C) D1, D2 FREQUENCY vs. TEMPERATURE VIN = 5.0V 750 700 650 600 550 600 -40 500 -40 40 60 80 100 60 FIGURE 11c 50 40 30 -20 20 0 40 60 80 80 100 120 140 160 LOAD CURRENT (mA) VIN = 4.5V -40 0 -20 20 40 60 80 100 15 TRANSFORMERS USED IN FIGURE 11c 14 13 TGM-030P3 TGM-010P3 4.5 4.0 TGM-020P3 12 TGM-030P3 11 10 TGM-010P3 9 8 7 TGM-020P3 6 2.5 60 1.0 OUTPUT VOLTAGE vs. LOAD CURRENT 5.0 3.0 40 VIN = 5.0V 1.1 TEMPERATURE (°C) 5.5 3.5 0 TRANSFORMERS USED IN FIGURE 11b 6.0 10 20 1.2 100 6.5 20 0 VIN = 5.5V 1.3 0.8 7.0 OUTPUT VOLTAGE (V) EFFICIENCY (%) FIGURE 11b 100 1.4 OUTPUT VOLTAGE vs. LOAD CURRENT 70 80 VIN = 6.0V 0.9 7.5 MAX845-07 90 60 40 1.5 TEMPERATURE (°C) EFFICIENCY vs. LOAD CURRENT 100 20 1.6 FS LOW TEMPERATURE (°C) 80 0 1.7 OUTPUT VOLTAGE (V) 20 -20 SUPPLY CURRENT vs. TEMPERATURE FS HIGH 750 650 0 -40 TEMPERATURE (°C) VIN = 5.0V VIN = 4.5V -20 100 800 FREQUENCY (kHz) FREQUENCY (kHz) VIN = 5.5V 700 80 D1, D2 FREQUENCY vs. TEMPERATURE VIN = 6.0V 800 60 850 MAX845-04 950 850 0.6 TEMPERATURE (°C) 1000 900 40 20 SUPPLY CURRENT (mA) 20 MAX845-05 0 MAX845-08 -20 0.8 0.2 2.5 -40 1.0 0.4 3.0 10 1.2 MAX845-06 20 SD = VCC 1.4 MAX845-09 OUTPUT RESISTANCE (Ω) VIN = 4.5V SHUTDOWN CURRENT (µA) 35 FIGURE 11b 7.0 1.6 MAX845-02 FIGURE 11c OUTPUT RESISTANCE (Ω) 7.5 MAX845-01 40 SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE OUTPUT RESISTANCE vs. TEMPERATURE MAX845-03 OUTPUT RESISTANCE vs. TEMPERATURE 5 0 20 40 60 80 100 120 140 160 LOAD CURRENT (mA) 0 20 40 60 80 100 120 140 160 LOAD CURRENT (mA) _______________________________________________________________________________________ 3 MAX845 __________________________________________Typical Operating Characteristics (Typical Operating Circuit, VIN = 5V, C1 = 0.1µF, C2 = C3 = 0.33µF, T1 = Halo TGM-010P3, CR1 = CR2 = MBR0520, FS = VCC, TA = +25°C, unless otherwise noted.) MAX845 Isolated Transformer Driver for PCMCIA Applications ____________________________Typical Operating Characteristics (continued) (Typical Operating Circuit, VIN = 5V, C1 = 0.1µF, C2 = C3 = 0.33µF, T1 = Halo TGM-010P3, CR1 = CR2 = MBR0520, FS = VCC, TA = +25°C, unless otherwise noted.) SWITCHING WAVEFORM (BREAK-BEFORE-MAKE) SWITCHING WAVEFORMS (TWO CYCLES) D1OFF D1 D2OFF 500mV/div 5V/div D2 CIRCUIT OF FIG. 1 D2ON 400ns/div D1ON 200ns/div TIME FROM SHUTDOWN TO POWER-UP SD 2V/div OUTPUT 5µs/div _____________________Pin Description VIN 4 PIN NAME FUNCTION 1 D1 Open Drain of N-Channel Transformer Drive 1 2 GND1 Ground. Connect both GND1 and GND2 to ground. 3 FS Frequency Select (internal pull-up). If FS = VCC or open, switch frequency = 725kHz; if FS = 0V, switch frequency = 535kHz. 4 SD Shutdown. Ground for normal operation, connect to VCC for shutdown. 5 N.C. No Connect. Not internally connected. 6 VCC +5V Supply Voltage 7 GND2 Ground. Connect both GND1 and GND2 to ground. 8 D2 Open Drain of N-Channel Transformer Drive 2 5V C1 0.1µF R1 50Ω 6 VCC 4 SD D1 1 ON / OFF R2 50Ω MAX845 3 FREQUENCY SELECT FS D2 GND1 2 GND2 7 Figure 1. Test Circuit _______________________________________________________________________________________ 8 Isolated Transformer Driver for PCMCIA Applications 5V C1 VCC D1 Q OUTPUT 5V @ 150mA CR1 N C2 T FS FREQUENCY SELECT VCC F/F MAX845 MAX845 VIN OSC 400kHz/ 700kHz D2 Q N SD ON / OFF GND2 CR2 C3 GND1 ISO GND Figure 2. Detailed Block Diagram _______________Detailed Description The MAX845 is a transformer driver specifically designed to provide isolated power for PCMCIA and other height- and/or space-sensitive applications. It drives a center-tapped transformer primary from a 5V or 3.3V DC power supply. The secondary can be wound to provide any isolated DC voltage needed at power levels up to 750mW. The 450kHz minimum switching frequency allows the use of very thin transformers, making the MAX845 ideal for PCMCIA and other space-limited applications. The MAX845 is designed to drive a single transformer less than 0.09 inches (2.3mm) in height, including package. Further reduction down to 0.050 inches (1.27mm) can be achieved using a transformer without a package. The MAX845 consists of an RC oscillator driving a pair of N-channel power switches. The oscillator runs at double the output frequency, driving a toggle flip-flop to ensure 50% duty cycle to each of the switches. Internal circuitry ensures break-before-make action between the two switches. A low-current shutdown mode disables all internal circuitry, including the oscillator and both power switches. Drive the shutdown pin (SD) high to shut down the part; drive SD low for normal operation. The SD pin has no internal default condition and must not be allowed to float. Most MAX845 applications will operate at high frequencies. The frequency-select pin (FS) is pulled high or left open (FS is internally pulled up to VCC) to operate at a minimum of 450kHz. Pulling FS low selects the low-frequency state. Theory of Operation Figure 2 shows the MAX845 driving both a TGM-010P3 transformer with a center-tapped primary, and a secondary with a voltage-doubler rectifier topology. All of the transformers driven by the MAX845 must have a center tap with VIN applied. Whenever one of the MAX845 outputs (D1 or D2) goes low, the other goes to approximately double the supply voltage. A voltage is induced in the secondary and the rectifier diodes steer the currents into the appropriate output capacitor. On alternate half cycles, each capacitor is charged. The output voltage is the sum of the voltages from each output capacitor. This topology yields the simplest and smallest transformer because the least number of secondary turns is required for a given voltage. __________Applications Information With the MAX845 transformer driver, designers have the advantages of push/pull converter topology in space-sensitive applications. The push/pull DC-DC converter topology allows isolated multiple outputs, step-up/step-down or inverted outputs, easier filtering on the input and the output, and lower overall noise. Isolated Power for PCMCIA Applications Medical instrumentation, modems, and LAN-interface cards often require isolated power supplies. One of the best switching-regulator topologies for this application is the push/pull forward-converting DC-DC power supply shown in Figures 3 and 4. Because the transformer works in the forward mode (rather than the flyback mode), its core does not store energy and, therefore, can be small. Input and output capacitors can be small because of the high-frequency and continuous-current waveforms. _______________________________________________________________________________________ 5 MAX845 Isolated Transformer Driver for PCMCIA Applications VIN 5V 0.01µF 1N4148 C1 0.1µF 1N4148 6 4 ON / OFF 3.3V SUPPLY VCC SD D1 1 MBR0520 1CT:1.3CT 5V @ 150mA ISO OUTPUT 6 VCC C2 0.33µF D1 1 MAX845 MAX845 3 FREQUENCY SELECT FS D2 GND1 GND2 2 8 MBR0520 ISO GND 7 GND1 2 D2 GND2 8 SEE FIGURE 11 FOR RECTIFIER CONFIGURATIONS 7 Figure 3. 5V to Isolated 5V Application Circuit Figure 4. 3.3V Input to Isolated Output Application Circuit The MAX845 is a versatile transformer driver, capable of driving a center-tapped transformer primary from a 5V or 3.3V DC power supply (Figures 3 and 4). The secondary can be wound to provide any isolated voltage needed at power levels up to 750mW with a 5V supply or up to 500mW with a 3.3V supply. Figure 3 shows a typical 5V to isolated 5V application circuit that delivers up to 150mA of isolated 5V power. will be higher at 3.3V, so transformer winding resistance will be more critical and efficiencies will be lower. The MAX845 output current must still be limited to 200mA (see Absolute Maximum Ratings), so the available output power will be less than with a 5V power source. 3.3V Supply Any of the application circuits shown may be converted to 3.3V operation by changing the turns ratio of the transformer and operating the MAX845 from a boost supply, as shown in Figure 4. In normal operation, whenever one of the MAX845 outputs goes low, the other goes to approximately double the supply voltage. Since the circuit is symmetrical, the two outputs can be combined with diodes, lightly filtered, then used to power the MAX845, and possibly other light loads as well. The diodes on the primary side may be any fast-switching small-signal diodes, such as the 1N914, 1N4148, or CMPD2838. The value of the primary filter capacitor is not critical and can be very small, since it only needs to supply current to the MAX845 during the break-beforemake interval. The transformer could be any of the same ones used for 5V operation, but for optimum performance it should have fewer primary turns, as the ET product required is now only 3.3V-µs. For a given power level, the currents 6 Low-Noise Power Supply The MAX845 topology is inherently low noise, in that either one or the other of the two power devices is on at any given time. By alternating between two identical states with one side on and the other off, the input current is nearly constant and secondary output power is available at all times. There is an intentional breakbefore-make action to prevent any possibility of both power switches conducting at the same time. During this 100ns non-overlap interval, the input current goes to zero. This adds a small high-frequency component to the input current waveform. This ripple current can easily be absorbed by a small input bypass capacitor (0.33µF) from VCC to ground. Figure 5 shows a lownoise bias supply using the MAX845 transformer driver. When using the two-diode push-pull (Figure 11a) rectifier or the four-diode bridge (Figure 11b), the output voltage tends to be more constant than in most alternative topologies. As described above, the circuit alternates between two identical states that both provide power to the load. The only part of the cycle that produces output ripple is the 100ns non-overlap interval, which can easily be filtered by a small ceramic output capacitor (0.33µF). _______________________________________________________________________________________ Isolated Transformer Driver for PCMCIA Applications D1 VCC MAX845 6 5V IN 1 0.33µF MBR0520L* MAX845 78L05 N.C. 3 IN FS OUT GND 4 0.33µF D2 SD GND1 2 GND2 7 N.C. 8 HALO TGM-030P3 -5V 100mA 5 *1N914 POSSIBLE FOR LOWER CURRENTS Figure 5. Low-Noise Supply Isolated Data Conversion Almost any serial-interface device is a candidate for operation across an isolation barrier; Figure 6 illustrates one example. The MAX176 analog-to-digital converter (ADC) operates from +5V and -12V supplies, provided by the multiple-tapped secondary and linear regulators. This circuit easily supplies several hundred milliwatts of additional isolated power for signal conditioning, multiplexing, or sensors. A +12V supply can be generated by adding two more diodes from the ends of the secondary, and a -5V supply can be generated by connecting additional diodes to the 1⁄4 and 3⁄4 tap points on the secondary. The MAX845 supplies sufficient power for almost any Maxim ADC. Telephone-Subscriber-Line Power Supply The standard telephone system is placed in the “off hook” state by placing a load on the line to signal the central office that service is requested. Normally, most of this power is wasted in a load resistor, but some systems can benefit from utilizing this free power. Figure 7 shows one way to transform the wasted telephone power to an isolated, regulated 5V at currents up to 50mA. Because the telephone line is a high-impedance source, there can be a start-up problem with any DCto-DC converter; when the line voltage is low during start-up, the frequency can be too low for the transformer, causing it to saturate. This excess saturation current can keep the voltage from climbing to normal operating levels. Thus the purpose of Q1, Q2, and the associated resistors is to ensure that the MAX845 remains in the shutdown mode until the voltage is high enough to allow proper operation. Isolated 4mA to 20mA Analog Interface The 4mA to 20mA current loop is widely used in the process-control industry for transducer and actuator control signals. These signals are commonly referred to a distant ground that may be at a considerably higher voltage with respect to the local ground. The circuit in Figure 8 generates an isolated 4mA to 20mA current from a 5V supply. Isolated RS-485 Data Interface The MAX845 power-supply transformer driver also provides isolated power for RS-485 data-interface applications. The application circuit of Figure 9 combines the MAX845 with a low-dropout linear regulator, a transformer, several high-speed optocouplers, and a Maxim RS-485 interface device. Isolated RS-232 Data Interface The MAX845 is ideal for isolated RS-232 data-interface applications requiring more than four transceivers. Its 750mW output power capability enables it to drive 10 transceivers simultaneously. Figure 10 shows the typical application circuit for a complete 120kbps isolated RS-232 data interface. This figure also shows how the Sharp PC417 optocouplers can be replaced by the lower-cost Quality Technologies 4N25 devices to achieve data transfer rates up to 19.2kbps. _______________________________________________________________________________________ 7 MAX845 Isolated Transformer Driver for PCMCIA Applications ISOLATION BARRIER 1CT : 1.5CT : 3CT VIN 5V INPUT 1 78L05 4 x 1N5817 10µF ISO 5V 6 3 8 79L12 ISO -12V D1 MAX845 VCC FS D2 GND1 10µF 4 SD 2 ON/OFF GND2 7 74HC04 START 8 6N136 7 INPUT CLOCK 1 2 200Ω QH 3k 14 6 10µF 5 MAX176 0.1µF ANALOG INPUT 1 2 3 0.1µF 10µF VDD AIN VREF VSS CONVST CLOCK 4 GND 3 DATA 8 8 7 6 5 6N136 7 4 11 1 12 200Ω 5V INPUT 0.1µF 10µF SIGNAL GROUND 3 5 1 QC RCK 10 QA SCLR 5 4 3 2 1 15 8 D11(MSB) D10 D9 D8 5V INPUT 0.1µF 74HC04 8 2 7 3 6 4 5 8 QH′ 8.2k 14 11 QH QG SER 74HC595 QF QE SCK QD 12 QC RCK QB 5V INPUT 10 QA SCLR 7 6 5 4 3 2 1 15 16 13 Figure 6. Typical Isolated Data-Conversion Application 8 6 16 13 4 6N136 QE SCK QB 3k 470Ω 74HC595 QF QD 2 6 QG SER 7 _______________________________________________________________________________________ 8 D7 D6 D5 D4 D3 D2 D1 D0 (LSB) 5V INPUT 0.1µF Isolated Transformer Driver for PCMCIA Applications MAX845 TELEPHONE SUBSCRIBER LINE ISOLATION BARRIER 6.8V 2W 1k D1 6 VCC Q1 2N3906 100k D1 1 T1 1:2:1 D2 1N5817 22k IC2 TL431 0.1µF C1 0.1µF IC1 22k 100k 4 2M 680k MAX845 SD D2 FS 100k Q2 2N3904 100k 5V @ 50mA ISO OUTPUT GND1 2 ISO GND 8 3 N.C. D3 1N5817 GND2 7 Figure 7. 5V from Telephone-Subscriber Line VIN ISOLATION BARRIER 1CT:5CT 6 5V VCC D1 1 24V UNREGULATED 1N5817 10µF IN 78L05 MAX845 4 SD GND1 2 GND GND2 7 D2 8 OUT 1N5817 3 3 1 7 0.1V to 0.5V MAX480 2 6 4 49.9k IL300 2 2 3 6 4 5 6 MAX480 ISO 5V 7 RL 0k to 1k IOUT 4mA to 20mA 2N3904 4 2N3904 10k 49.9k 24.9Ω Figure 8. Typical 4mA/20mA Application Circuit _______________________________________________________________________________________ 9 MAX845 Isolated Transformer Driver for PCMCIA Applications ISOLATION BARRIER VIN 5V C1 0.1µF 6 VCC D1 ON / OFF 4 SD 2 8 C3 0.1µF MAX845 D2 GND1 ICT:1.3CT 1N5817 1 GND2 FS IN OUT C2 2.2µF ISO 5V 2 C4 2.2µF MAX883 8 3 1N5817 N.C. SET GND 6 SHDN 4 5 7 3.3k PC410 / 417 6 *74HC04 390Ω DI 1 5 3.3k 3 8 4 PC357T *74HC04 390Ω DE 4 1 4 A 3 *74HC04 3.3k DE 1 B 1 RO RE GND 2 *74HC04 OR EQUIVALENT 4 3 Figure 9. Typical RS-485 Application Circuit 10 485 I/O 6 390Ω 6 MAX481 MAX483 MAX485 MAX487 2 3 PC410 / 417 5 RO VCC DI ______________________________________________________________________________________ 5 7 Isolated Transformer Driver for PCMCIA Applications 5V C1 0.1µF 5 ON / OFF 4 6 VCC N.C. SD D1 1 MAX845 D2 FS GND1 GND2 2 7 8 2 IN OUT C2 2.2µF MAX883 C3 0.1µF SET GND SHDN 6 4 5 MBR0520 N.C. 5 x 3.3k 390Ω 6 1 T1IN 3 5 4 2 74HC04 390Ω 4 T2IN 74HC04 ISO 5V C4 2.2µF 8 3 10 x PC417 *74HC04 MAX845 ISOLATION BARRIER 1CT:1.3CT MBR0520 VIN 390Ω 25 27, 28 13, 14 VCC GND 11 T1IN T1OUT T2IN T2OUT T3IN T3OUT T4IN T4OUT T5IN T5OUT 12 18 T3IN 74HC04 390Ω 24 T4IN 74HC04 390Ω 23 T5IN R1OUT 74HC04 6 5 4 1 390Ω 5 390Ω 6 390Ω 7 R3OUT 74HC04 390Ω 22 R4OUT 74HC04 R5OUT R1OUT R1IN R2OUT R2IN R3OUT R3IN R4OUT R4IN R5OUT R5IN 10 2 R2OUT 74HC04 16 MAX225 5 x 3.3k 74HC04 17 390Ω 21 SD 1 9 8 19 20 EN 2 *74HC04 OR EQUIVALENT 4N25 LOWER SPEED, LOWER COST ALTERNATE OPTOCOUPLER CONFIGURATIONS (FOR DATA RATES BELOW 9.6kbps) VCC 1N5711 4N25 6 1N5711 6 4N25 3.3k 3.3k 390Ω 1 1 ROUT TIN ISO 5 5 TIN 390Ω 74HCO4 *74HC04 2 2 ISO ISO 4 4 GND GND VCC ISO ROUT Figure 10. Typical RS-232 Application Circuit ______________________________________________________________________________________ 11 MAX845 Isolated Transformer Driver for PCMCIA Applications ______________Component Selection Transformer The MAX845 drives any transformer that has a centertapped primary and a saturation rating of at least 5V-µs (ET product) per side. The oscillator frequency varies linearly with VCC. The transformer is most vulnerable to saturation at the minimum frequency, because the switches are on for the longest period. At VCC = 4.5V, the transformer must withstand at least: 1 1 4.5V x ———–——— x — = 5V-µs 450kHz min 2 And at VCC = 5.5V, the transformer must withstand at least: 1 1 5.5V x ———–——— x — = 5V-µs 550kHz min 2 Thus, the required ET product is constant over the entire 5V ±10% range. Select either a toroid or a gapped core. Although some applications will require custom transformers, many can use standard transformer designs, such as those listed in Table 1. Some of these manufacturers have standard products designed for the MAX845, while some have standard products that can be adapted for specific customer requirements. Table 1 also lists some suppliers of suitable magnetic cores. Table 1. Transformer and Transformer-Core Suppliers TRANSFORMERS TRANSFORMER CORES Halo Electronics Magnetics Inc. Phone: (415) 969-7313 Phone: (412) 282-8282 FAX: (415) 367-7158 FAX: (412) 282-6955 Ask for MAX845 Transformer Coilcraft Fair-Rite Products Phone: (708) 639-6400 Phone: (914) 895-2055 FAX: (708) 639-1469 FAX: (914) 895-2629 Ask for MAX845 Transformer BH Electronics Philips Components Phone: (612) 894-9590 Phone: (401) 762-3800 FAX: (612) 894-9380 FAX: (401) 762-3805, ext. 324 Ask for MAX845 Transformer Sumida USA Phone: (708) 956-0666 FAX: (708) 956-0702 12 MMG (Magnetic Materials Group) Phone: (201) 345-8900 FAX: (201) 345-1172 Amidon Associates Phone: (714) 850-4660 FAX: (714) 850-1163 An ungapped toroid core must never be allowed to saturate. An empirical way to measure a toroid’s ET product is to wind 20 turns on the bare core and observe the current waveform on an oscilloscope while driving the winding with a function generator. Generate a 50% duty-cycle square wave at a test frequency of 500kHz, with no DC offset. Gradually increase the driving voltage until the waveform suddenly begins to draw more current. At this point, the core is saturating, so reduce the driving voltage until the core just barely stops saturating. The ET product indicated is simply the maximum voltage that can be applied without saturation, multiplied by 1µs (the time of half of the period of the input signal). Because the ET product varies linearly with the number of turns, this test winding can be scaled up or down to act as a suitable primary for that particular core. A gapped core, such as a bobbin or drum core, is not limited by ET product, but rather by inductance and winding resistance. The primary inductance must be high enough to prevent excessive current flow under light-load conditions, yet low enough that it can be wound on the core. Good results can be achieved by using a primary inductance between 50µH and 200µH. Calculate the number of turns required by using the manufacturer’s AL (inductance per turn squared) value, or measure a test winding with an inductance meter. Inductance varies with the square of the number of turns. While most MAX845 applications will use a toroid transformer for highest efficiency and lowest EMI, there may be applications that can utilize less expensive transformers, such as E, I, or U-shaped cores, magnetic bobbins, or etched windings on a printed circuit board. Table 1 lists some transformer and core suppliers who can assist with your magnetics design. The secondary or secondaries can be scaled to produce whatever output is required for the application at hand, taking into account the rectifier topology to be used and the forward voltage loss of the diodes selected. Step-by-Step Transformer Design Procedure Before starting the design, determine the minimum and maximum output voltage requirement, the minimum and maximum load current, the physical size constraints, and the cost budget. 1) Select an appropriate core shape and material from core vendors’ data sheets; trade-off EMI vs. space and cost. Since the MAX845’s output waveform is a square wave, it is rich in harmonics, so choose a material with low losses at up to several MHz. ______________________________________________________________________________________ Isolated Transformer Driver for PCMCIA Applications VIN 3) Determine the number of turns required for the primary winding. For an ungapped toroid, ET product from center-tap to D1 must be at least 5V-µs. Other core types must have sufficient inductance to limit D1 and D2 output current under minimum load conditions, and must not be allowed to saturate. 4) Select a rectifier topology based on performance requirements (ripple vs. loss, and space required for secondary winding). Refer to Table 2, Rectifier Topology Trade-Offs. 5) Work backward from VOUT requirements to determine the secondary to primary turns ratio. Include losses in the rectifier diodes, and estimate resistive losses in the windings. For load currents exceeding 150mA, use a voltage step-down transformer to step up the output current from the MAX845. Do not exceed the MAX845’s absolute maximum output current rating (200mA). 6) Wind the transformer with the largest diameter wire that will fit the winding area. Select a wire gauge to fill the winding aperture as much as possible. Larger diameter wire has lower resistance per unit length. Doubling the wire diameter reduces resistive losses by a factor of four. Bobbin or drum cores suffer from low coupling between windings. This usually requires bifilar winding for the two halves of the primary. Due to the inherent complexity of magnetic circuit design, it will be necessary to build a prototype and reiterate the design. If necessary, adjust the design by altering the number of primary or secondary turns, or the wire gauge. If using a different core material or geometry, evaluate its ET product or AL as described above. 6 VCC MAX845 2) Use a test winding to measure ET product (if using an ungapped toroid) and/or AL value for the core. 1 D1 MAX845 GND1 GND2 2 7 8 D2 Figure 11a. 2-Diode Push-Pull VIN 6 VCC D1 1 MAX845 GND1 GND2 2 7 D2 8 Figure 11b. 4-Diode Bridge VIN 6 VCC D1 1 MAX845 GND1 GND2 2 7 D2 8 Figure 11c. Voltage Doubler Rectifier Topology Diodes Figure 11 shows various rectifier topologies. Refer to Table 2 for selection criteria. The turns ratio of the transformer must be set to provide the minimum required output voltage at the maximum anticipated load, with the minimum expected input voltage. In addition, the calculations should allow for worst-case losses in the rectifiers. Since the turns ratio determined in this manner will ordinarily produce a much higher voltage at the secondary under conditions of high input voltage and/or light loading, be careful to prevent an overvoltage condition from occurring (see the Output Voltage vs. Load Current graph in the Typical Operating Characteristics). Use fast-switching diode rectifiers. Ordinary silicon signal diodes like the 1N914 or 1N4148 may be used for low output current levels (less than 50mA), but Schottky diodes have a lower forward voltage drop and should be used for higher-current applications. Central Semiconductor has low-current Schottky diodes as duals in SOT-23 packages (CMPSH-3 series). The Nihon SB05W05C is a common-cathode dual in a SOT23; it works well in the two-diode full-wave configuration. The Motorola MBR0520 is an excellent choice for all configurations. ______________________________________________________________________________________ 13 MAX845 Isolated Transformer Driver for PCMCIA Applications RS SIMPLE SHUNT ZENER RS 22k TL431 5V OUTPUT 22k PROGRAMMABLE-IC SHUNT REGULATOR (STAND ALONE) RS Output Filter Capacitor 1k 22k 2N2907 5V OUTPUT TL431 22k PROGRAMMABLE-IC SHUNT REGULATOR WITH DISCRETE PNP Figure 12. Shunt-Regulator Circuits Output Regulator Since the output voltage is not regulated against changes in the input voltage or load current, an output voltage regulator may be needed. A series linear regulator gives good performance and reasonably good efficiency at low cost. A shunt regulator costs less, occupies less space, and gives adequate performance for some applications. Series regulators such as the MAX666, MAX667, MAX882/MAX883/MAX884, or MAX603/MAX604 simplify designs. Just select one with the desired output voltage and current capability, and connect it. 14 The simplest voltage regulator is the shunt zener shown in Figure 12. The series resistor (RS) value should be as high as possible to still deliver the maximum expected load current with minimum input voltage. Be sure that no ratings are exceeded at maximum input voltage and minimum load current conditions; under such conditions, the zener diode may have to dissipate much more power than the load. Alternatively, start with the maximum allowable zener dissipation and select the series resistor under light-load, high-line conditions. Then verify that there is sufficient output current available with worstcase low input voltage. For better regulation than the simple shunt zener, consider a shunt regulator IC such as the TL431. This device behaves like a zener diode whose voltage can be programmed by a resistor ratio. It can be used as a stand-alone device or can be boosted above its 150mA maximum rating without compromising its accuracy by adding a discrete PNP transistor, as shown in Figure 12. The input power of a shunt regulator is nearly independent of load, so efficiency at light loads tends to be worse than it would be with a series regulator. Ceramic capacitors can be used as output capacitors because of the lower level of output ripple current. In applications where output ripple is not critical, a 0.33µF chip or ceramic capacitor is normally sufficient. Refer to Table 3 for suggested capacitor suppliers. In applications sensitive to output-ripple noise, the output filter capacitor (C2) should have a low equivalent series resistance (ESR) and a low equivalent series inductance (ESL), and its capacitance should remain fairly constant over temperature. Sprague 595D surface-mount solid tantalum capacitors and Sanyo OS-CON through-hole capacitors are recommended, if space allows, due to their extremely low ESR. Capacitor ESR usually rises at low temperatures, but OSCON capacitors provide very low ESR below 0°C. Input Bypass Capacitor The input bypass capacitor (C1) is not critical. Unlike switching regulators, the MAX845’s supply current is fairly constant, and is therefore less dependent on the input bypass capacitor. A low-cost 0.33µF chip or ceramic capacitor is normally sufficient for input bypassing. ______________________________________________________________________________________ Isolated Transformer Driver for PCMCIA Applications Table 3. Suggested Capacitor Suppliers CAPACITOR TOPOLOGY 2-Diode Push/Pull (Figure 11a) ADVANTAGE • Only 3 external components • Low output ripple DISADVANTAGE 4-Diode Bridge (Figure 11b) Voltage Doubler (Figure 11c) • Simpler transformer winding requirements • Low output ripple SUPPLIER Low-ESR 267 Series Matsuo USA Phone: (714) 969-2491 FAX: (714) 960-6492 Ceramic Murata Erie USA Phone: (800) 831-9172 FAX: (404) 436-3030 Very Low-ESR 595D/293D Series Sprague Electric Co. USA Phone: (603) 224-1961 FAX: (603) 224-1430 • More turns on transformer • Single diode drop MAX845 Table 2. Rectifier Topology Trade-Offs • 5 external components • Higher cost • 2 diode drops • 4 external components • Fewest turns on transformer • Higher output ripple • 2 diode drops ___________________Chip Topography D1 D2 0.085" (2.159mm) GND1 GND2 FS V CC SD 0.058" (1.4732mm) SUBSTRATE CONNECTED TO VCC TRANSISTOR COUNT: 31 ______________________________________________________________________________________ 15 8LUMAXD.EPS ________________________________________________________Package Information SOICN.EPS MAX845 Isolated Transformer Driver for PCMCIA Applications 16 ______________________________________________________________________________________