AD OP271FZ

a
High-Speed, Dual
Operational Amplifier
OP271
PIN CONNECTIONS
FEATURES
Excellent Speed: 8.5 V/ms Typ
Fast Settling (0.01%): 2 ms Typ
Unity-Gain Stable
High-Gain Bandwidth: 5 MHz Typ
Low Input Offset Voltage: 200 mV Max
Low Offset Voltage Drift: 21 mV/∞C Max
High Gain: 400 V/mV Min
Outstanding CMR: 106 dB Min
Industry Standard 8-Pin Dual Pinout
Available in Die Form
GENERAL DESCRIPTION
–IN A 1
16
OUT A
+IN A 2
15
NC
NC 3
14
NC
V– 4
13
V+
NC 5
12
NC
+IN B 6
11
NC
–IN B 7
10
OUT B
NC 8
9
NC
NC = NO CONNECT
The OP271 is a unity-gain stable monolithic dual op amp
featuring excellent speed, 8.5 V/ms typical, and fast settling
time, 2 ms typical to 0. 01%. The OP271 has a gain bandwidth
of 5 MHz with a high phase margin of 62∞.
16-Pin SOL
(S-Suffix)
Input offset voltage of the OP271 is under 200 mV with input
offset voltage drift below 2 mV/∞C, guaranteed over the full
military temperature range. Open-loop gain exceeds 400,000
into a 10 kW load ensuring outstanding gain accuracy and
linearity. The input bias current is under 20 nA limiting
errors due to source resistance. The OP271’s outstanding
CMR, over 106 dB, and low PSRR, under 5.6 mV/V, reduce
errors caused by ground noise and power supply fluctuations.
In addition, the OP27l exhibits high CMR and PSRR over a
wide frequency range, further improving system accuracy.
8 V+
OUT A 1
–IN A 2
A
– +
B
+ –
7 OUT B
+IN A 3
6 –IN B
V– 4
5 +IN B
Epoxy Mini-DIP
(P-Suffix)
8-Pin Hermetic DIP
(Z-Suffix)
V+
BIAS
OUT
–IN
+IN
V–
REV. A
Figure 1. Simplified Schematic
(One of the two amplifiers is shown.)
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
OP271–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (V = ±15 V, T = 25∞C, unless otherwise noted.)
S
Parameter
Symbol
INPUT OFFSET
VOLTAGE
VOS
INPUT OFFSET
CURRENT
IOS
INPUT BIAS
CURRENT
INPUT NOISE
VOLTAGE
DENSITY
LARGE-SIGNAL
VOLTAGE
GAIN
INPUT VOLTAGE
RANGE
Conditions
A
OP271A/E
Min Typ Max
Min
OP271F
Typ Max
Min
OP271G
Typ Max
Unit
75
200
150
300
200
400
mV
VCM = 0 V
1
10
4
15
7
20
nA
IB
VCM = 0 V
4
20
6
40
12
60
nA
en
fO = 1 kHz
7.6
AVO
VO = ± 10 V
RL = 10 kW
RL = 2 kW
IVR
7.6
7.6
nV/Hz
400
300
650
500
300
200
500
300
250
175
400
250
V/mV
V/mV
± 12
± 12.5
± 12
± 12.5
± 12
± 12.5
V
OUTPUT
VOLTAGE SWING VO
RL ≥ 2 kW
± 12
± 13
± 12
± 13
± 12
± 13
V
COMMON-MODE
REJECTION
CMR
VCM = ± 12 V
106
120
100
115
90
105
dB
POWER SUPPLY
REJECTION
RATIO
PSRR
VS = ± 4.5 V
to ± 18 V
SLEW RATE
SR
PHASE MARGIN
um
AV = +1
62
SUPPLY CURRENT
(ALL AMPLIFIERS) ISY
No Load
45
GAIN
BANDWIDTH
PRODUCT
CHANNEL
SEPARATION
0.6
5.5
GBW
CS
3.2
8.5
1.8
5.5
125
125
8.5
6.5
4.5
175
175
125
125
2.4
5.5
62
5
VO = 20 Vp-p
fO = 10 Hz
5.6
6.5
7.0
mV/V
8.5
V/ms
62
degrees
4.5
6.5
mA
5
5
MHz
175
175
175
175
dB
dB
INPUT
CAPACITANCE
CIN
3
3
3
pF
INPUT
RESISTANCE
DIFFERENTIALMODE
RIN
0.4
0.4
0.4
MW
INPUT
RESISTANCE
COMMON
MODE
RINCM
20
20
20
GW
SETTLING TIME
tS
2
2
2
ms
AV = +1,
10 V Step
to 0.01%
NOTES
1
Guaranteed by CMR test.
2
Guaranteed but not 100% tested.
–2–
REV. A
OP271
ELECTRICAL CHARACTERISTICS (V = ±15 V, –55∞C £ T £ 125∞C for OP271A, unless otherwise noted.)
S
A
OP271A
Typ
Max
Unit
VOS
115
400
mV
AVERAGE INPUT OFFSET
VOLTAGE DRIFT
TCVOS
0.4
2
mV/∞C
INPUT OFFSET CURRENT
IOS
VCM = 0 V
1.5
30
nA
INPUT BIAS CURRENT
IB
VCM = 0 V
7
60
nA
LARGE-SIGNAL VOLTAGE
GAIN
AVO
VO = ± 10 V
RL = 10 kW
RL = 2 kW
INPUT VOLTAGE RANGE1
IVR
OUTPUT VOLTAGE SWING
VO
COMMON-MODE REJECTION
Parameter
Symbol
INPUT OFFSET VOLTAGE
Conditions
Min
300
200
600
500
V/mV
V/mV
± 12
± 12.5
V
RL ≥ 2 kW
± 12
± 13
V
CMR
VCM = ± 12 V
100
120
dB
POWER SUPPLY REJECTION
RATIO
PSRR
VS = ± 4.5 V to ± 18 V
1.0
5.6
mV/V
SUPPLY CURRENT
(ALL AMPLIFIERS)
ISY
No Load
5.3
75
mA
OP271G
Typ Max
Unit
NOTE
1
Guaranteed by CMR test.
ELECTRICAL CHARACTERISTICS
(VS = ±15 V, –40∞C £ TA £ +85∞C, unless otherwise noted.)
Parameter
Symbol
Min
INPUT OFFSET
VOLTAGE
VOS
Conditions
AVERAGE INPUT
OFFSET
VOLTAGE DRIFT TCVOS
OP271A/E
Typ Max
Min
OP271F
Typ Max
Min
100
330
215
560
300
700
mV
0.4
2
1
4
2.0
5
mV/∞C
INPUT OFFSET
CURRENT
IOS
VCM = 0 V
1
30
5
40
15
50
nA
INPUT BIAS
CURRENT
IB
VCM = 0 V
6
60
10
70
15
80
nA
AVO
VO = ± 10 V
RL = 10 kW
RL = 2 kW
LARGE-SIGNAL
VOLTAGE GAIN
INPUT VOLTAGE
RANGE1
IVR
300
200
600
500
200
100
500
400
150
90
400
300
V/mV
V/mV
± 12
± 12.5
± 12
± 12.5
± 12
± 12.5
V
OUTPUT
VOLTAGE SWING VO
RL ≥ 2 kW
± 12
± 13
± 12
± 13
± 12
± 13
V
COMMON-MODE
REJECTION
CMR
VCM = ± 12 V 100
120
94
115
90
100
dB
PSRR
VS = ± 4.5 V
to ± 18 V
0.7
5.6
No Load
5.2
7.2
POWER SUPPLY
REJECTION
RATIO
SUPPLY CURRENT
(ALL AMPLIFIERS) ISY
NOTE
1
Guaranteed by CMR test.
REV. A
–3–
51.8
5.2
10
7.2
2.0
5.2
15
mV/V
7.2
mA
OP271
(Continued from Page 1)
ORDERING GUIDE
The OP271 offers outstanding dc and ac matching between channels. This is especially valuable for applications such as multiple
gain blocks, high-speed instrumentation and amplifiers, buffers
and active filters.
Package
TA = 25∞C
VOS Max
(mV)
The OP271 conforms to the industry standard, 8-pin dual op amp
pinout. It is pin compatible with the TL072, TL082, LF412,
and 1458/1558 dual op amps and can be used to significantly
improve systems using these devices.
200
200
300
400
400
For applications requiring lower voltage noise, see the OP270.
For a quad version of the OP271, see the OP471.
CERDIP
8-Pin
Plastic
Operating
Temperature
Range
OP271GP
*OP271GS
MIL
XND
XND
XND
XND
*OP271AZ
*OP271EZ
*OP271FZ
*Not for new design, obsolete April 2002.
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Differential Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . ± 1.0 V
Differential Input Current2 . . . . . . . . . . . . . . . . . . . . ± 25 mA
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage
Output Short-Circuit Duration . . . . . . . . . . . . . . Continuous
Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . 300∞C
Junction Temperature (Tj) . . . . . . . . . . . . . –65∞C to +150∞C
Operating Temperature Range
OP271A . . . . . . . . . . . . . . . . . . . . . . . . . . . –55∞C to +125∞C
OP271E, OP271F, OP271G . . . . . . . . . . . –40∞C to +85∞C
Package Type
␪jA3
␪jC
Unit
8-Pin Hermetic DIP (Z)
8-Pin Plastic DIP (P)
8-Pin SOIC (S)
134
96
92
12
37
27
∞C/W
∞C/W
∞C/W
NOTES
1
Absolute maximum ratings apply to packaged parts, unless otherwise noted.
2
The OP271’s inputs are protected by back-to-back diodes. Current limiting
resistors are not used in order to achieve low-noise performance. If differential
voltage exceeds ± 1.0 V, the input current should be limited to ± 25 mA.
3
␪jA is specified for worst case mounting conditions, i.e., ␪jA is specified for
device in socket for CERDIP and P-DIP packages; ␪jA is specified for device
soldered to printed circuit board for SOIC package.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the OP271 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. A
Typical Performance Characteristics– OP271
25
VOLTAGE NOISE DENSITY – nV/ Hz
40
20
10
5
4
3
1/f CORNER = 40Hz
2
1
100
10
FREQUENCY – Hz
10
AT 1kHz
0
5
10
15
SUPPLY VOLTAGE – Volts
20
100
1/f CORNER = 40Hz
0.1
10
100
1k
FREQUENCY – Hz
80
60
40
20
0
–20
–75
10k
TPC 4. Current Noise Density vs.
Frequency
0.001
10
INPUT OFFSET CURRENT – nA
4
2
0
10k
–50 –25
0
25
50
75
TEMPERATURE – C
100
TA = 25C
VS = 15V
9
8
7
6
5
4
3
2
1
125
0
1
2
3
TIME – Minutes
4
5
TPC 6. Warm-Up Offset Voltage Drift
7
TA = 25C
VS = 15V
4
6
100
1k
FREQUENCY – Hz
TPC 3. Total Harmonic Distortion vs.
Frequency
5
VS = 15V
VCM = 0V
AV = 10
AV = 1
0
TPC 5. Input Offset Voltage vs.
Temperature
10
AV = 100
10
VS = 15V
1.0
TA = 25C
VS = 15V
VO = 10Vp-p
RL = 2k
0.01
120
TA = 25C
VS = 15V
INPUT OFFSET VOLTAGE – V
CURRENT NOISE DENSITY – pA/ Hz
15
TPC 2. Voltage Noise Density vs.
Supply Voltage
10.0
INPUT BIAS CURRENT – nA
AT 10Hz
5
1k
TPC 1. Voltage Noise Density vs.
Frequency
8
20
CHANGE IN OFFSET VOLTAGE – V
1
0.1
TA = 25C
3
INPUT BIAS CURRENT – nA
VOLTAGE NOISE DENSITY – nV/ Hz
TA = 25C
VS = 15V
TOTAL HARMONIC DISTORTION – %
100
2
1
0
–1
–2
–3
6
5
4
3
–4
–2
–75 –50 –25
0
25
50
75
TEMPERATURE – C
100 125
TPC 7. Input Bias Current vs.
Temperature
REV. A
–5
–75 –50 –25
0
25
50
75
TEMPERATURE – C
100 125
TPC 8. Input Offset Current vs.
Temperature
–5–
2
–12.5
–7.5
–2.5 0 2.5
7.5
COMMON MODE VOLTAGE – Volts
12.5
TPC 9. Input Bias Current vs.
Common-Mode Voltage
OP271
130
7
7
VS = 15V
110
100
80
70
60
50
40
30
TA = 25C
VS = 15V
20
10
1
10
100
1k
10k
FREQUENCY – Hz
100k
6
TA = +125C
5
3
1M
TPC 10. CMR vs. Frequency
TA = +25C
4
TA = –55C
10
15
5
SUPPLY VOLTAGE – Volts
0
+PSR
60
40
80
60
40
1
10
100
0
1k 10k 100k 1M 10M 100M
FREQUENCY – Hz
TPC 13. PSR vs. Frequency
1
10
100
40
20
0
–20
1k
1k 10k 100k 1M 10M 100M
FREQUENCY – Hz
TPC 14. Open-Loop Gain vs.
Frequency
25
PHASE MARGIN = 62C
140
5
160
0
180
10M
8
VS = 15V
1500
PHASE MARGIN – DEG
120
GAIN
10
100
OPEN-LOOP GAIN – V/mV
15
100k
1M
FREQUENCY – Hz
80
TA = 25C
RL = 10k
PHASE SHIFT – DEG
PHASE
TA = 25C
VS = 15V
10k
TPC 15. Closed-Loop Gain vs.
Frequency
2000
20
OPEN-LOOP GAIN – dB
60
20
20
0
100 125
TA = 25C
VS = 15V
CLOSED-LOOP GAIN – dB
OPEN-LOOP GAIN – dB
PSR – dB
–PSR
–25 0
25
50
75
TEMPERATURE – C
80
100
80
–50
TA = 25C
VS = 15V
120
100
4
TPC 12. Total Supply Current vs.
Temperature
140
TA = 25C
120
5
3
–75
20
TPC 11. Total Supply Current vs.
Supply Voltage
140
6
1000
500
6
70
GBW
60
50
m
4
2
–5
–10
1
2
3
4 5
FREQUENCY – MHz
6 7 8 10
TPC 16. Open-Loop Gain, Phase Shift
vs. Frequency
0
0
5
10
15
SUPPLY VOLTAGE – Volts
20
TPC 17. Open-Loop Gain vs. Supply
Voltage
–6–
40
–75 –50 –25
GAIN-BANDWIDTH PRODUCT – MHz
CMR – dB
90
TOTAL SUPPLY CURRENT – mA
TOTAL SUPPLY CURRENT – mA
120
0
0 25 50 75 100 125 150
TEMPERATURE – C
TPC 18. Gain-Bandwidth Product,
Phase Margin vs. Temperature
REV. A
OP271
180
20
24
20
TA = 25C
VS = 15V
18
16
12
8
16
160
POSITIVE SWING
14
120
12
100
NEGATIVE SWING
10
4
8
6
4
10k
100k
1M
FREQUENCY – Hz
0
100
10M
TPC 19. Maximum Output Swing
vs. Frequency
1k
LOAD RESISTANCE – 10k
TPC 20. Maximum Output Voltage
vs. Load Resistance
12
AV = 1
60
40
AV = 100
0
100
1k
100k
10k
FREQUENCY – Hz
CHANNEL SEPARATION – dB
10
TA = 25C
VS = 15V
180
11
–SR
9
+SR
8
7
170
160
150
140
130
120
110
100
90
80
6
0
25
50
75
–75 –50 –25
TEMPERATURE – C
70
10
100 125
TPC 22. Slew Rate vs. Temperature
1M
10M
TA = 25C
VS = 15V
AV = +1
50mV
5s
TPC 24. Large-Signal Transient
Response
REV. A
1k
10k
100k
FREQUENCY – Hz
TPC 23. Channel Separation vs.
Frequency
TA = 25C
VS = 15V
AV = +1
5V
100
200ns
TPC 25. Small Signal Transient
Response
–7–
1M
10M
TPC 21. Output Impedance vs.
Frequency
190
VS = 15V
SLEW RATE – V/S
80
20
2
0
1k
TA = 25C
VS = 15V
140
OUTPUT IMPEDANCE – TA = 25C
VS = 15V
THD = 1%
RL = 10k
MAXIMUM OUTPUT – Volts
PEAK-TO-PEAK AMPLITUDE – Volts
28
OP271
When Rf > 3 k⍀, a pole created by Rf and the amplifier’s
input capacitance (3 pF) creates additional phase shift and
reduces phase margin. A small capacitor in parallel with Rf
helps eliminate this problem.
APPLICATION INFORMATION
Capacitive Load Driving and Power Supply Considerations
The OP217 is unity-gain stable and is capable of driving large
capacitive loads without oscillating. Nonetheless, good supply
bypassing is highly recommended. Proper supply bypassing
reduces problems caused by supply line noise and improves
the capacitive load driving capability of the OP271.
Computer Simulations
Many electronic design and analysis programs include models
for op amps which calculate AC performance from the location
of poles and zeros. As an aid to designers utilizing such a
program, major poles and zeros of the OP271 are listed below.
Their location will vary slightly between production lots.
Typically, they will be within ⴞ15% of the frequency listed.
Use of this data will enable the designer to evaluate gross
circuit performance quickly, but should not supplant rigorous
characterization of a breadboard circuit.
In the standard feedback amplifier, the op amp’s output resistance
combines with the load capacitance to form a low-pass filter that
adds phase shift in the feedback network and reduces stability. A
simple circuit to eliminate this effect is shown in Figure 2. The
added components, C1 and R3, decouple the amplifier from the
load capacitance and provide additional stability. The values of
C1 and R3 shown in Figure 8 are for a load capacitance of up to
1000 pF when used with the OP271.
POLES
V+
C2
10␮F
+
C3
0.1␮F
Low Phase Error Amplifier
The simple amplifier depicted in Figure 4, utilizes a monolithic
dual operational amplifier and a few resistors to substantially
reduce phase error compared to conventional amplifier designs.
At a given gain, the frequency range for a specified phase
accuracy is over a decade greater than for a standard single op
amp amplifier.
R3
50⍀
VIN
VOUT
OP271
C4
10␮F
+
C5
0.1␮F
2.5 MHz
4 X 23 MHz
-
APPLICATIONS
R2
C1
200pF
R1
ZEROS
15Hz
1.2 MHz
2 X 32 MHz
8 X 40 MHz
CL
1000pF
The low phase error amplifier performs second-order frequency
compensation through the response of op amp A2 in the
feedback loop of A1. Both op amps must be extremely well
matched in frequency response. At low frequencies, the A1
feedback loop forces V2/(K1 + 1)=VIN. The A2 feedback loop
forces VO/VIN=K1 + 1. The DC gain is determined by the
resistor divider around A2. Note that, like a conventional
single op amp amplifier, the DC gain is set by resistor ratios
only. Minimum gain for the low phase error amplifier is 10.
PLACE SUPPLY DECOUPLING
CAPACITORS AT OP271
V–
Figure 2. Driving Large Capacitive Loads
Unity-Gain Buffer Applications
When Rf ⱕ 100 ⍀ and the input is driven with a fast, large-signal
pulse (>1 V), the output waveform will look as shown in Figure
3.
R2
R2 = R1
R2
K1
During the fast feedthrough-like portion of the output, the input
protection diodes effectively short the output to the input, and a
current, limited only by the output short-circuit protection, will
be drawn by the signal generator. With Rf ⱖ 500 ⍀, the output is
capable of handling the current requirements (IL ⱕ 20 mA at
10 V); the amplifier will stay in its active mode and a smooth
transition will occur.
1/2
OP271E
A2
1/2
OP271E
A1
R1
V2
R1
R1
K1
VIN
VO
ASSUME: A1 AND A2 ARE MATCHED.
OP271
␻
8.5V/␮s
AO(s) = s
VO = (K1+1) VIN
Figure 4. Low Phase Error Amplifier
Figure 3. Pulsed Operation
–8–
REV. A
OP271
Dual 12-Bit Voltage Output DAC
The dual voltage output DAC shown in Figure 6 will settle to
12-bit accuracy from zero to full scale in 2 s typically. The
CMOS DAC-8222 utilizes a 12-bit, double-buffered input
structure allowing faster digital throughput and minimizing
digital feedback.
0
PHASE SHIFT – DEG
–1
–2
–3
SINGLE OP AMP,
CONVENTIONAL
DESIGN
–4
–5
Fast Current Pump
Maximum output current of the fast current pump shown in
Figure 7 is 11 mA. Voltage compliance exceeds 10 V with
15 V supplies. The current pump has an output resistance
of over 3 M and maintains 12-bit linearity over its entire
output range.
CASCADED
(TWO STAGES)
LOW PHASE ERROR
AMPLIFIER
–6
–7
0.001
0.1
0.01
0.005
0.005
FREQUENCY RATIO – 1/ /
1.0
0.5
R3
10k
Figure 5. Phase Error Comparison
R1
10k
Figure 5 compares the phase error performance of the low
phase error amplifier with a conventional single op amp
amplifier and a cascaded two-stage amplifier. The low phase
error amplifier shows a much lower phase error, particularly for
frequencies where T<0.1. For example, phase error of
-0.1 occurs at 0.002 T for the single op amplifier, but
at 0.11 T for the low phase error amplifier.
VIN
2
1/2
OP271FZ
R2
10k
R5
100
1
3
+15V
R4
10k
For more detailed information on the low phase error amplifier,
see Application Note AN-107.
5
8
7
1/2
OP271FZ
6
4
IOUT =
V
VIN
= IN =10mA/V
RS 100
–15V
Figure 7. Fast Current Pump
+15V
10F
5V
0.1F
21
VDD
DAC-8222EW
10V
REFERENCE
VOLTAGE
RFBA
3
8
10pF
4 VREFA
DAC A
IOUTA
2
2
–
1/2
OP271EZ
3
AGND
12-BIT DATABUS PINS 6–17
VOUTA
+
1
4
–15V
0.1F
22 VREFB
DAC
CONTROL
DAC B
18 DAC A/DAC B
19 LDAC
20 WR
IOUTB
RFBB
24
6
23
–
1/2
OP271EZ
10pF
5
7
+
DGND
Figure 6. Dual 12-Bit Voltage Output DAC
REV. A
–9–
10F
VOUTB
IOUT
11mA
OP271
OUTLINE DIMENSIONS
8-Lead Ceramic Dip-Glass Hermetic Seal [CERDIP]
(Q-8)
8-Lead Plastic Dual-in-Line Package [PDIP]
(N-8)
Dimensions shown in inches and (millimeters)
Dimensions shown in inches and (millimeters)
0.005 (0.13)
MIN
8
0.055 (1.40)
MAX
0.375 (9.53)
0.365 (9.27)
0.355 (9.02)
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
4
8
5
1
4
0.295 (7.49)
0.285 (7.24)
0.275 (6.98)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54) BSC
0.405 (10.29) MAX
0.200 (5.08)
MAX
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.100 (2.54)
BSC
0.320 (8.13)
0.290 (7.37)
0.060 (1.52)
0.015 (0.38)
0.180
(4.57)
MAX
0.150 (3.81)
MIN
SEATING
0.070 (1.78) PLANE
0.030 (0.76)
0.015
(0.38)
MIN
15
0
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCH; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
SEATING
PLANE
0.060 (1.52)
0.050 (1.27)
0.045 (1.14)
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MO-095AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES)
8-Lead Standard Small Outline Package [SOIC]
Narrow Body
(RN-8)
Dimensions shown in millimeters and (inches)
5.00 (0.1968)
4.80 (0.1890)
4.00 (0.1574)
3.80 (0.1497)
8
5
1
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
SEATING
0.10
PLANE
6.20 (0.2440)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.33 (0.0130)
0.50 (0.0196)
45
0.25 (0.0099)
8
0.25 (0.0098) 0 1.27 (0.0500)
0.41 (0.0160)
0.19 (0.0075)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–10–
REV. A
OP271
Revision History
Location
Page
10/02—Data Sheet changed from REV. 0 to REV. A.
Deleted PIN CONNECTIONS Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Edits to Figure 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
REV. A
–11–
–12–
PRINTED IN U.S.A.
C00326-0-10/02(A)