ADS5404 www.ti.com SLAS945 – APRIL 2013 Dual Channel 12-Bit 500Msps Analog-to-Digital Converter Check for Samples: ADS5404 FEATURES 1 • • • • • • • • • • • Dual Channel 12-Bit Resolution Maximum Clock Rate: 500 Msps Low Swing Fullscale Input: 1.0 Vpp Analog Input Buffer with High Impedance Input Input Bandwidth (3 dB): >1.2 GHz Data Output Interface: DDR LVDS 196-Pin BGA Package (12x12mm) Power Dissipation: 910 mW/ch Performance at fin = 230 MHz IF – SNR: 60.6 dBFS – SFDR: 77 dBc Performance at fin = 700 MHz IF – SNR: 59.4 dBFS – SFDR: 70 dBc APPLICATIONS • • • • • • • Test and Measurement Instrumentation Ultra-Wide Band Software Defined Radio Data Acquisition Power Amplifier Linearization Signal Intelligence and Jamming Radar and Satellite Systems Microwave Receivers Device Part No. Number of Channels Speed Grade ADS5402 2 800Msps ADS5401 1 800Msps ADS5404 2 500Msps ADS5403 1 500Msps DESCRIPTION The ADS5404 is a high linearity dual channel 12-bit, 500 MSPS analog-to-digital converter (ADC) easing front end filter design for wide bandwidth receivers. The analog input buffer isolates the internal switching of the onchip track-and-hold from disturbing the signal source as well as providing a high-impedance input. Optionally the output data can be decimated by two. Designed for high SFDR, the ADC has low-noise performance and outstanding spurious-free dynamic range over a large input-frequency range. The device is available in a 196-pin BGA package and is specified over the full industrial temperature range (–40°C to 85°C). 12bit 500Msps INA Digital Block DA[11 :0] DACLK CLKIN Clk Buffer SYNCIN INB 12bit 500Msps Digital Block DB[11 :0] DBCLK 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2013, Texas Instruments Incorporated ADS5404 SLAS945 – APRIL 2013 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. OVRAP/N SRESETB DETAILED BLOCK DIAGRAM SCLK OVERRANGE SDO VOLTAGE REFERENCE SDENB CLKOUT GEN DC or Fs/2 Estimator ADC FIR FILTER Gain Correction DEC x2 Offset Correction SYNCP/N CLOCK DISTRIBUTION MULTICHIP SYNC INTERLEAVING CORRECTION INB_P/N ADC FIR FILTER Estimator Gain Correction BUFFER Offset Correction OVERRANGE DC or Fs/2 THRESHOLD DEC x2 DACLKP /N ... INA_P/N INTERLEAVING CORRECTION DA[11:0]P/N ... BUFFER CLKP /N SDIO CONTROL DDR LVDS OUTPUT BUFFER VCM THRESHOLD DDR LVDS OUTPUT BUFFER VREF PROGRAMMING DATA DB[11:0]P/N CLKOUT GEN SYNCOUTP /M DBCLKP /N SYNCOUTP /N OVRBP/N Figure 1. Detailed Block Diagram 2 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 PINOUT INFORMATION A B C D E F G H J K L M N P 14 VREF VCM GND INB_N INB_P GND AVDDC AVDDC GND INA_P INA_N GND GND CLKINP 14 13 SDENB TEST MODE GND GND GND GND GND GND GND GND GND GND GND CLKINN 13 12 SCLK SRESET B GND AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 GND AVDD33 AVDD33 12 11 SDIO ENABLE GND AVDD18 AVDD18 AVDD18 AVDD18 AVDD18 AVDD18 AVDD18 AVDD18 GND AVDD18 AVDD18 11 10 SDO IOVDD GND AVDD18 GND GND GND GND GND GND AVDD18 GND NC NC 10 9 DVDD DVDD GND GND GND GND GND GND GND GND GND GND SYNCN SYNCP 9 8 DVDD DVDD DVDD DVDD GND GND GND GND GND GND DVDD DVDD DVDD DVDD 8 7 DB0N DB0P DVDD LVDS DVDD LVDS GND GND GND GND GND GND DVDD LVDS DVDD LVDS NC NC 7 6 DB1N DB1P DVDD LVDS DVDD LVDS GND GND GND GND GND GND DVDD LVDS DVDD LVDS NC NC 6 5 DB2N DB2P OVRBN OVRBP GND GND GND GND GND GND OVRAN OVRAP SYNC OUTN SYNC OUTP 5 4 DB3N DB3P DB8P DB10P NC NC NC DA0P DA2P DA4P DA6P DA8P NC NC 4 3 DB4N DB4P DB8N DB10N NC NC NC DA0N DA2N DA4N DA6N DA8N DA11N DA11P 3 2 DB5N DB5P DB7P DB9P DB11P SYNC OUTP DBCLKP DACLKP DA1P DA3P DA5P DA7P DA10N DA10P 2 1 DB6N DB6P DB7N DB9N DB11N SYNC OUTN DBCLKN DACLKN DA1N DA3N DA5N DA7N DA9N DA9P 1 A B C D E F J K L M N P G H Figure 2. Pinout in DDR output mode (top down view) PIN ASSIGNMENTS PIN NAME NUMBER I/O DESCRIPTION INPUT/REFERENCE INA_P/N K14, L14 I Analog ADC A differential input signal. INB_P/N D14, E14 I Analog ADC B differential input signal. VCM B14 O Output of the analog input common mode (nominally 1.9V). A 0.1μF capacitor to AGND is recommended. VREF A14 I Reference voltage input. A 0.1μF capacitor to AGND is recommended, but not required. CLKINP/N P14, P13 I Differential input clock SYNCP/N P9, N9 I Synchronization input. Inactive if logic low. When clocked in a high state initially, this is used for resetting internal clocks and digital logic and starting the SYNCOUT signal. Internal 100Ω termination. B12 I Serial interface reset input. Active low. Initialized internal registers during high to low transition. Asynchronous. Internal 50kΩ pull up resistor to IOVDD. CLOCK/SYNC CONTROL/SERIAL SRESET Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 3 ADS5404 SLAS945 – APRIL 2013 www.ti.com PIN ASSIGNMENTS (continued) PIN NAME NUMBER I/O DESCRIPTION ENABLE B11 I Chip enable – active high. Power down function can be controlled through SPI register assignment. Internal 50kΩ pull up resistor to IOVDD. SCLK A12 I Serial interface clock. Internal 50kΩ pull-down resistor. SDIO A11 I/O SDENB A13 I Serial interface enable. Internal 50kΩ pull-down resistor. SDO A10 O Uni-directional serial interface data in 4 pin mode (register x00, D16). The SDO pin is tristated in 3-pin interface mode (default). Internal 50kΩ pull-down resistor. TESTMODE B13 – Factory internal test, do not connect DA[11:0]P/N P3, N3, P2, N2, P1, N1, M4, M3, M2, M1, L4, L3, L2, L1, K4, K3, K2, K1, J4, J3, J2, J1, H4, H3 O ADC A Data Bits 11 (MSB) to 0 (LSB) in DDR output mode. Standard LVDS output. DB[11:0]P/N E2, E1, D4, D3, D2, D1, C4, C3, C2, C1, B1, A1, B2, A2, B3, A3, B4, A4, B5, A5, B6, A6, B7, A7 O ADC B Data Bits 11 (MSB) to 0 (LSB) in DDR output mode. Standard LVDS output. DACLKP/N H2, H1 O DDR differential output data clock for Bus A. Register programmable to provide either rising or falling edge to center of stable data nominal timing. DBCLKP/N G2, G1 O DDR differential output data clock for Bus B. Register programmable to provide either rising or falling edge to center of stable data nominal timing. Optionally Bus B can be latched with DACLKP/N. F2, F1, P5, N5 O Synchronization output signal for synchronizing multiple ADCs. Can be disabled via SPI. OVRAP/N M5, L5 O Bus A, Overrange indicator, LVDS output. A logic high signals an analog input in excess of the full-scale range. Optional SYNC output. OVRBP/N D5, C5 O Bus B, Overrange indicator, LVDS output. A logic high signals an analog input in excess of the full-scale range. Optional SYNC output. E3, E4, F3, F4, G3, G4, N4, N6, N7, N10, P4, P6, P7, P10 – Don’t connect to pin D12, E12, F12, G12, H12, J12, K12, L12, N12, P12 I 3.3V analog supply AVDDC G14, H14 I 1.8V supply for clock input AVDD18 D10, D11, E11, F11, G11, H11, J11, K11, L10, L11, N11, P11 I 1.8V analog supply DVDD A8, A9, B8, B9, C8, D8, L8, M8, N8, P8 I 1.8V supply for digital block DVDDLVDS C6, C7, D6, D7, L6, L7, M6, M7 I 1.8V supply for LVDS outputs B10 I 1.8V for digital I/Os I Ground Bi-directional serial data in 3 pin mode (default). In 4-pin interface mode (register x00, D16), the SDIO pin in an input only. Internal 50kΩ pull-down. DATA INTERFACE SYNCOUTP/N NC POWER SUPPLY AVDD33 IOVDD GND 4 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 PACKAGE/ORDERING INFORMATION PRODUCT PACKAGELEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE ECO PLAN(2) ADS5404 196-BGA ZAY –40°C to 85°C GREEN (RoHS & no Sb/Br) LEAD/BALL FINISH PACKAGE MARKING ADS5404I ORDERING NUMBER TRANSPORT MEDIA, QUANTITY ADS5404IZAY Tray ADS5404IZAYR Tape and Reel ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) VALUE MIN MAX UNIT Supply voltage range, AVDD33 –0.5 4 V Supply voltage range, AVDDC –0.5 2.3 V Supply voltage range, AVDD18 –0.5 2.3 V Supply voltage range, DVDD –0.5 2.3 V Supply voltage range, DVDDLVDS –0.5 2.3 V Supply voltage range, IOVDD –0.5 4 V INA/B_P, INA/B_N –0.5 AVDD33 + 0.5 V CLKINP, CLKINN –0.5 AVDDC + 0.5 V SYNCP, SYNCN –0.5 AVDD33 + 0.5 V SRESET, SDENB, SCLK, SDIO, SDO, ENABLE –0.5 IOVDD + 0.5 V Voltage applied to input pins Operating free-air temperature range, TA –40 Operating junction temperature range, TJ Storage temperature range –65 ESD, Human Body Model 85 °C 150 °C 150 °C 2 kV THERMAL INFORMATION ADS5404 THERMAL METRIC (1) nFBGA UNITS 196 PINS Junction-to-ambient thermal resistance (2) θJA (3) 37.6 θJCtop Junction-to-case (top) thermal resistance θJB Junction-to-board thermal resistance (4) 16.8 ψJT Junction-to-top characterization parameter (5) 0.2 ψJB Junction-to-board characterization parameter (6) 16.4 6.8 °C/W spacer (1) (2) (3) (4) (5) (6) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7). Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 5 ADS5404 SLAS945 – APRIL 2013 www.ti.com RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN Recommended operating junction temperature TJ TA (1) NOM MAX 105 Maximum rated operating junction temperature (1) 125 Recommended free-air temperature –40 25 85 UNIT °C °C Prolonged use at this junction temperature may increase the device failure-in-time (FIT) rate. ELECTRICAL CHARACTERISTICS Typical values at TA = 25°C, full temperature range is TMIN = –40°C to TMAX = 85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, –1dBFS differential input (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS ADC Clock Frequency 40 500 MSPS Resolution 12 Bits SUPPLY AVDD33 3.15 3.3 3.45 V AVDDC, AVDD18, DVDD, DVDDLVDS 1.7 1.8 1.9 V IOVDD 1.7 1.8 3.45 V POWER SUPPLY IAVDD33 3.3V Analog supply current 297 330 mA IAVDD18 1.8V Analog supply current 84 100 mA IAVDDC 1.8V Clock supply current 26 45 mA IDVDD 1.8V Digital supply current Auto correction enabled 230 260 mA IDVDD 1.8V Digital supply current Auto correction disabled 106 mA IDVDD 1.8V Digital supply current Auto correction disabled, decimation filter enabled 135 mA IDVDDLVDS 1.8V LVDS supply current IIOVDD 1.8V I/O Voltage supply current Pdis Total power dissipation Auto correction enabled, decimation filter disabled Pdis Total power dissipation Auto correction disabled, decimation filter disabled PSRR 250 kHz to 500 MHz Shut-down power dissipation Shut-down wake up time Standby power dissipation Standby wake up time Deep-sleep mode power dissipation mA 2 mA 1.84 1.62 40 W W dB 7 mW 2.5 ms 7 mW µs Auto correction disabled 282 mW Auto correction enabled 370 mW 20 µs Auto correction disabled 549 mW Auto correction enabled 650 mW Light-sleep mode wakeup time 6 170 1 100 Deep-sleep mode wakeup time Light-sleep mode power dissipation 140 2 Submit Documentation Feedback µs Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 ELECTRICAL CHARACTERISTICS Typical values at TA = 25°C, full temperature range is TMIN = –40°C to TMAX = 85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD3V = 3.3V, AVDD/DRVDD/IOVDD = 1.8V, –1dBFS differential input (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS ANALOG INPUTS Differential input full-scale 1.0 1.25 Input common mode voltage 1.9 ±0.1 Vpp V Input resistance Differential at DC 1 kΩ Input capacitance Each input to GND 2 pF VCM common mode voltage output 1.9 Analog input bandwidth (3dB) V 1200 MHz DYNAMIC ACCURACY Offset Error Auto correction disabled –20 –7.5 20 Auto correction enabled –1 0 1 Offset temperature coefficient –611 Gain error –5 Gain temperature coefficient mV mV µV/°C 5 0.005 %FS %FS/°C Differential nonlinearity fIN = 230 MHz –1 ±0.9 2 LSB Integral nonlinearity fIN = 230 MHz –5 ±1.5 5 LSB 500 MHz CLOCK INPUT Input clock frequency 40 Input clock amplitude 2 Input clock duty cycle 40% Internal clock biasing 50% Vpp 60% 0.9 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 V 7 ADS5404 SLAS945 – APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS Typical values at TA = 25°C, full temperature range is TMIN = –40°C to TMAX = 85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, –1dBFS differential input (unless otherwise noted). PARAMETER TEST CONDITIONS MIN Auto Correction TYP MAX MIN TYP MAX Enabled Disabled fIN = 10 MHz 60.8 60.8 fIN = 100 MHz 60.7 60.8 60.6 60.7 fIN = 450 MHz 60.2 60.6 fIN = 700 MHz 59.4 60.1 fIN = 10 MHz 84 86 fIN = 100 MHz 84 82 UNITS Vpp DYNAMIC AC CHARACTERISTICS (1) SNR HD2,3 Non HD2,3 IL Signal to Noise Ratio Second and third harmonic distortion Spur Free Dynamic Range (excluding second and third harmonic distortion) Fs/2-Fin interleaving spur SINAD THD IMD3 Signal to noise and distortion ratio Total Harmonic Distortion Inter modulation distortion fIN = 230 MHz fIN = 230 MHz 59 80 83 fIN = 450 MHz 82 84 fIN = 700 MHz 76 74 fIN = 10 MHz 77 78 fIN = 100 MHz 77 78 77 77 fIN = 450 MHz 74 75 fIN = 700 MHz 70 71 fIN = 10 MHz 92 80 fIN = 100 MHz 83 79 fIN = 230 MHz fIN = 230 MHz 70 70 83 79 fIN = 450 MHz 79 76 fIN = 700 MHz 75 73 fIN = 10 MHz 60.6 60.7 fIN = 100 MHz 60.6 60.7 60.5 60.7 fIN = 450 MHz 60.1 60.5 fIN = 700 MHz 59.3 60 fIN = 10 MHz 76.3 79.0 fIN = 100 MHz 76.5 77.6 fIN = 230 MHz fIN = 230 MHz 70 57.5 68 (1) 8 Effective number of bits dBc dBc dBc dBFS 77.4 78.1 fIN = 450 MHz 76.3 77.9 fIN = 700 MHz 73.4 72.9 Fin = 129.5 and 130.5 MHz, -7 dBFS 82 82 Fin = 349.5 and 350.5 MHz, -7 dBFS 80 80 90 90 dB fIN = 230 MHz 9.8 9.8 LSB Crosstalk ENOB dBFS dBc dBFS SFDR and SNR calculations do not include the DC or Fs/2 bins when Auto Correction is disabled. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 ELECTRICAL CHARACTERISTICS Typical values at TA = 25°C, full temperature range is TMIN = –40°C to TMAX = 85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, –1dBFS differential input (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNITS OVER-DRIVE RECOVERY ERROR Input overload recovery Recovery to within 5% (of final value) for 6dB overload with sine wave input 2 ns SAMPLE TIMING CHARACTERISTICS rms Aperture Jitter Sample uncertainty 100 fs rms ADC sample to digital output, auto correction disabled 38 ADC sample to digital output, auto correction enabled 50 Clock Cycles ADC sample to digital output, Decimation filter enabled, Auto correction disabled 74 Sampling clock Cycles ADC sample to over-range output 12 Clock Cycles Data Latency Over-range Latency ELECTRICAL CHARACTERISTICS The DC specifications refer to the condition where the digital outputs are not switching, but are permanently at a valid logic level 0 or 1. AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V PARAMETER TEST CONDITIONS MIN TYP MAX UNITS DIGITAL INPUTS – SRESET, SCLK, SDENB, SDIO, ENABLE High-level input voltage Low-level input voltage All digital inputs support 1.8V and 3.3V logic levels. 0.7 x IOVDD V 0.3 x IOVDD V High-level input current –50 200 µA Low-level input current –50 50 µA Input capacitance 5 pF DIGITAL OUTPUTS – SDO Iload = -100 µA High-level output voltage Iload = -2 mA IOVDD – 0.2 V 0.8 x IOVDD Iload = 100 µA Low-level output voltage 0.2 0.22 x IOVDD Iload = 2 mA V DIGITAL INPUTS – SYNCP/N VID Differential input voltage VCM Input common mode voltage tSU 250 350 450 1.125 1.2 1.375 500 mV V ps DIGITAL OUTPUTS – DA[11:0]P/N, DACLKP/N, OVRAP/N, SYNCOUTP/N, DB[11:0]P/N, DBCLKP/N, OVRBP/N VOD Output differential voltage IOUT = 3.5 mA 250 350 450 VOCM Output common mode voltage IOUT = 3.5 mA 1.125 1.25 1.375 tsuA Fs = 500 Msps, Data valid to zero-crossing of DACLK 600 800 ps thA Fs = 500 Msps, Zero-crossing of DACLK to data becoming invalid 600 790 ps tsuB Fs = 500 Msps, Data valid to zero-crossing of DBCLK 700 900 ps thB Fs = 500 Msps, Zero-crossing of DBCLK to data becoming invalid 500 600 ps Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 mV V 9 ADS5404 SLAS945 – APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS (continued) The DC specifications refer to the condition where the digital outputs are not switching, but are permanently at a valid logic level 0 or 1. AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V PARAMETER MIN TYP MAX UNITS tPD Fs = 500 Msps, CLKIN falling edge to DACLK, DBCLK rising edge TEST CONDITIONS 3.28 3.48 3.74 ns tRISE 10% - 90% 100 150 200 ps tFALL 90% - 10% 100 150 200 ps Data Latency ? Clock Cycles SAMPLE N CLKINP tPD DACLKP DBCLKP DCLK edges are centered within the data valid window DA[11:0]P/N DB[11:0]P/N OVRAP/N ORVBP/N N-1 N N+1 CLKIN, DCLK are differential: Only the ‘P’ positive signal shown for clarity tsu th Figure 3. Timing Diagram for 12-bit DDR Output 10 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 TYPICAL CHARACTERISTICS Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. FFT FOR 10 MHz INPUT SIGNAL (auto on) FFT FOR 10 MHz INPUT SIGNAL (auto off) Figure 4. Figure 5. FFT FOR 230 MHz INPUT SIGNAL (auto on) FFT FOR 230 MHz INPUT SIGNAL (auto off) Figure 6. Figure 7. FFT FOR 450 MHz INPUT SIGNAL (auto on) FFT FOR 450 MHz INPUT SIGNAL (auto off) Figure 8. Figure 9. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 11 ADS5404 SLAS945 – APRIL 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. 12 FFT FOR 700 MHz INPUT SIGNAL (auto on) FFT FOR 700 MHz INPUT SIGNAL (auto off) Figure 10. Figure 11. SFDR vs INPUT FREQUENCY SNR vs INPUT FREQUENCY Figure 12. Figure 13. SFDR vs AMPLITUDE (fin = 230MHz) SNR vs Amplitude (fin = 230 MHz) Figure 14. Figure 15. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. Tow Tone Performance Across Input Amplitude (fin = 130MHz) SFDR vs Vref (auto on) Figure 16. Figure 17. SFDR vs Vref (auto off) SNR vs Vref (auto on) Figure 18. Figure 19. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 13 ADS5404 SLAS945 – APRIL 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. 14 SNR vs Vref (auto off) Performance Across Input Common Mode Voltage Figure 20. Figure 21. Performance Across Temperature (fin = 230MHz) Performance Across AVDD33 (fin = 230MHz) Figure 22. Figure 23. Performance Across AVDD18 (fin = 230MHz) Performance Across Clock Amplitude Figure 24. Figure 25. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. INL DNL Figure 26. Figure 27. CMRR Across Frequency PSRR Across Frequency Figure 28. Figure 29. Power Across Sampling Frequency Figure 30. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 15 ADS5404 SLAS945 – APRIL 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. SFDR Across Input and Sampling Frequencies (auto on) Figure 31. 16 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. SFDR Across Input and Sampling Frequencies (auto off) Figure 32. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 17 ADS5404 SLAS945 – APRIL 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. SNR Across Input and Sampling Frequencies (auto on) Figure 33. 18 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 TYPICAL CHARACTERISTICS (continued) Typical values at TA = +25°C, full temperature range is TMIN = -40°C to TMAX = +85°C, ADC sampling rate = 500Msps, 50% clock duty cycle, AVDD33 = 3.3V, AVDDC/AVDD18/DVDD/DVDDLVDS/IOVDD = 1.8V, -1dBFS differential input, unless otherwise noted. SNR Across Input and Sampling Frequencies (auto on) Figure 34. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 19 ADS5404 SLAS945 – APRIL 2013 www.ti.com FEATURES POWER DOWN MODES The ADS5404 can be configured via SPI write (address x37) to a stand-by, light or deep sleep power mode which is controlled by the ENABLE pin. The sleep modes are active when the ENABLE pin goes low. Different internal functions stay powered up which results in different power consumption and wake up time between the two sleep modes. Sleep mode Wake up time Power Consumption Auto correction disabled Power Consumption Auto correction enabled Complete Shut Down 2.5 ms 7mW 7mW Stand-by 100µs 7mW 7mW Deep Sleep 20µs 282mW 370mW Light Sleep 2µs 549mW 650mW TEST PATTERN OUTPUT The ADS5404 can be configured to output different test patterns that can be used to verify the digital interface is connected and working properly. To enable the test pattern mode, the high performance mode 1 has to be disabled first via SPI register write. Then different test patterns can be selected by configuring registers x3C, x3D and x3E. All three registers must be configured for the test pattern to work properly. First set HP1 = 0 (Addr 0x01, D01) Register Address All 0s All 1s Toggle (0xAAA => 0x555) Toggle (0xFFF => 0x000) 0x3C 0x8000 0xBFFC 0x9554 0xBFFC 0x3D 0x0000 0x3FFC 0x2AA8 0x0000 0x3E 0x0000 0x3FFC 0x1554 0x3FFC Register Address x3C x3D x3E Custom Pattern D15 1 0 0 D14 0 0 0 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D1 0 0 0 D0 0 0 0 For normal operation, set HP1 = 1 (Addr 0x01, D01) and 0x3C, 0x3D, 0x3E all to 0. CLOCK INPUT The ADS5404 clock input can be driven differentially with a sine wave, LVPECL or LVDS source with little or no difference in performance. The common mode voltage of the clock input is set to 0.9V using internal 2kΩ resistors. This allows for AC coupling of the clock inputs. The termination resistors should be placed as close as possible to the clock inputs in order to minimize signal reflections and jitter degradation. 0.1uF CLKINP CLKINP 2kΩ RT 0.9V 0.1uF 2kΩ RT CLKINN CLKINN 0.1uF Recommended differential clock driving circuit Figure 35. Recommended Differential Clock Driving Circuit 20 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 SNR AND CLOCK JITTER The signal to noise ratio of the ADC is limited by three different factors: the quantization noise is typically not noticeable in pipeline converters and is 72dB for a 12bit ADC. The thermal noise limits the SNR at low input frequencies while the clock jitter sets the SNR for higher input frequencies. SNRQuantization _ Noise æ SNR ADC [dBc] = -20 ´ log çç 10 20 è 2 2 2 ö æ SNRThermalNoise ö æ SNRJitter ö + 10 ÷÷ + ç 10 ÷ ç ÷ 20 20 ø è ø ø è The SNR limitation due to sample clock jitter can be calculated as following: SNRJitter [dBc] = -20 ´ log(2p ´ fin ´ TJitter ) (1) (2) The total clock jitter (TJitter) has three components – the internal aperture jitter (100fs for ADS5404) which is set by the noise of the clock input buffer, the external clock jitter and the jitter from the analog input signal. It can be calculated as following: TJitter = (TJitter,Ext.Clock _ Input )2 + (TAperture _ ADC )2 + (TJitter,Analog_ input )2 (3) External clock jitter can be minimized by using high quality clock sources and jitter cleaners as well as bandpass filters at the clock input while a faster clock slew rate improves the ADC aperture jitter. The ADS5404 has a thermal noise of 60.8 dBFS and internal aperture jitter of 100fs. The SNR depending on amount of external jitter for different input frequencies is shown in the following figure. SNR vs Input Frequency and External Clock Jitter 62 61 35 fs 50 fs 100 fs 150 fs 200 fs SNR (dBFS) 60 59 58 57 56 55 10 100 1000 Fin (MHz) Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 21 ADS5404 SLAS945 – APRIL 2013 www.ti.com ANALOG INPUTS The ADS5404 analog signal inputs are designed to be driven differentially. The analog input pins have internal analog buffers that drive the sampling circuit. As a result of the analog buffer, the input pins present a high impedance input across a very wide frequency range to the external driving source which enables great flexibility in the external analog filter design as well as excellent 50Ω matching for RF applications. The buffer also helps to isolate the external driving circuit from the internal switching currents of the sampling circuit which results in a more constant SFDR performance across input frequencies. The common-mode voltage of the signal inputs is internally biased to 1.9V using 500Ω resistors which allows for AC coupling of the input drive network. Each input pin (INP, INM) must swing symmetrically between (VCM + 0.25V) and (VCM – 0.25V), resulting in a 1.0Vpp (default) differential input swing. The input sampling circuit has a 3dB bandwidth that extends up to 1.2GHz. 2nH 0.5Ω 20Ω INA_P 1.3pF 1.4pF 500Ω Vcm= 1.9V 2nH 0.5Ω 20Ω 500Ω INA_N 1.3pF 1.4pF OVER-RANGE INDICATION The ADS5404 provides a fast over-range indication on the OVRA/B pins. The fast OVR is triggered if the input voltage exceeds the programmable overrange threshold and it gets presented after just 12 clock cycles enabling a quicker reaction to an overrange event. The OVR threshold can be configured using SPI register writes. The input voltage level at which the overload is detected is referred to as the threshold and is programmable using the Over-range threshold bits. The threshold at which fast OVR is triggered is (full-scale × [the decimal value of the FAST OVR THRESH bits] /16). After reset, the default value of the over-range threshold is set to 15 (decimal) which corresponds to a threshold of 0.56dB below full scale (20*log(15/16)). OVR Detection Threshold 0 Thresholds set to dBFS -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 Programmed Value (1-15) 22 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 INTERLEAVING CORRECTION Each of the two data converter channels consists of two interleaved ADCs each operating at half of the ADC sampling rate but 180º out of phase from each other. The front end track and hold circuitry is operating at the full ADC sampling rate which minimizes the timing mismatch between the two interleaved ADCs. In addition the ADS5404 is equipped with internal interleaving correction logic that can be enabled via SPI register write. ADC ODD Track & Hold Input Fs Interleaving Correction Fs/2 0 deg ADC EVEN Estimator Fs/2 180 deg The interleaving operation creates 2 distinct and interleaving products: • Fs/2 – Fin: this spur is created by gain timing mismatch between the ADCs. Since internally the front end track and hold is operated at the full sampling rate, this component is greatly improved and mostly dependent on gain mismatch. • Fs/2 Spur: due to offset mismatch between ADCs Input Signal Fs/2 Spur Fs/2 - Fin Fs/2 The auto correction loop can be enabled via SPI register write in address 0x01. By default it is disabled for lowest possible power consumption. The DC correction function can be enabled in 0x03 & 0x1A for chA and chB respectively. The default settings for the auto correction function should work for most applications. However please contact Texas Instruments if further fine tuning of the algorithm is required. The auto correction function yields best performance for input frequencies below 250MHz. For input frequencies greater than 250MHz it is recommended to disable the auto gain correction loop. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 23 ADS5404 SLAS945 – APRIL 2013 www.ti.com DECIMATION FILTER Each channel has a digital filter in the data path as shown in Figure 36. The filter can be programmed as a lowpass or a high-pass filter and the normalized frequency response of both filters is shown in Figure 37. 500 MSPS Lowpass/ Highpass selection Low Latency Filter 250 MSPS ADC 2 0, Fs/2 Figure 36. The decimation filter response has a 0.1dB pass band ripple with approximately 41% pass-band bandwidth. The stop-band attenuation is approximately 40dB. Decimation Filter Response Decimation Filter Response 10 0.1 0.08 0 0.06 Low Pass Filter 0.04 High Pass Filter Attenuation (dB) Attenuation (dB) -10 -20 -30 0.02 0 -0.02 -0.04 -40 -0.06 -50 Low Pass Filter -0.08 -60 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0 0.05 Frequency (MHz) 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Frequency (MHz) Figure 37. 24 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 MULTI DEVICE SYNCHRONIZATION The ADS5404 simplifies the synchronization of data from multiple ADCs in one common receiver. Upon receiving the initial SYNC input signal, the ADS5404 resets all the internal clocks and digital logic while also starting a SYNCOUT signal which operates on a 5bit counter (32 clock cycles). Therefore by providing a common SYNC signal to multiple ADCs their output data can be synchronized as the SYNCOUT signal marks a specific sample with the same latency in all ADCs. The SYNCOUT signal then can be used in the receiving device to synchronize the FIFO pointers across the different input data streams. Thus the output data of multiple ADCs can be aligned properly even if there are different trace lengths between the different ADCs. ADS5404 DxCLK Sample x SYNCOUT Sample 1 Sample 2 Dx[11:0] ChA FIFO Pointer Sample 3 Sample 4 Sample 5 Sample 6 ... ChB FPGA ASIC SYNC ADS5404 ChA DxCLK Sample x SYNCOUT Sample 1 Dx[11:0] FIFO Pointer Sample 2 Sample 3 Sample 4 Sample 5 Sample 6 ... ChB The SYNC input signal should be a periodic signal repeating every 32 CLKIN clock cycles. It gets registered on the rising edge of the ADC input clock (CLKIN). Upon registering the initial rising edge of the SYNC signal, the internal clocks and logic get reset which results in invalid output data for 36 samples (1 complete sync cycle and 4 additional samples). The SYNCOUT signal starts with the next output clock (DACLK) rising edge and operates on a 5-bit counter independent from the SYNC signal frequency and duty cycle. Since the ADS5404 output interface operates with a DDR clock, the synchronization can happen on the rising edge or falling edge sample. Synchronization on the falling edge sample will result in a half cycle clock stretch of DA/BCLK. For convenience the SYNCOUT signal is available on the ChA/B output LVDS bus. When using decimation the SYNCOUT signal still operates on 32 clock cycles of CLKIN but since the output data is decimated by 2, only the first 18 samples should be discarded. CLKIN 16 clock cycles SYNC 16 clock cycles DACLK 16 clock cycles SYNCOUT 16 clock cycles DA[11:0] Data invalid – 36 samples SYNC 16 clock cycles 16 clock cycles DACLK SYNCOUT 16 clock cycles 16 clock cycles DA[11:0] Data invalid – 36 samples Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 25 ADS5404 SLAS945 – APRIL 2013 www.ti.com PROGRAMMING INTERFACE The serial interface (SIF) included in the ADS5404 is a simple 3 or 4 pin interface. In normal mode, 3 pins are used to communicate with the device. There is an enable (SDENB), a clock (SCLK) and a bi-directional IO port (SDIO). If the user would like to use the 4 pin interface one write must be implemented in the 3 pin mode to enable 4 pin communications. In this mode, the SDO pin becomes the dedicated output. The serial interface has an 8-bit address word and a 16-bit data word. The first rising edge of SCLK after SDENB goes low will latch the read/write bit. If a high is registered then a read is requested, if it is low then a write is requested. SDENB must be brought high again before another transfer can be requested. The signal diagram is shown below: Register Initialization After power up, the internal registers must be initialized to the default values. This initialization can be accomplished in one of two ways: 1. Either through hardware reset by applying a low pulse on SRESET pin 2. By applying a software reset. When using the serial interface, a reset can be performed by addressing register x2C. This setting initializes the internal registers to the default values and then self-resets the RESET register to 0. In this case the SRESET pin can be kept high. Serial Register Write The internal register of the ADS5404 can be programmed following these steps: 1. Drive SDENB pin low 2. Set the R/W bit to ‘0’ (bit A7 of the 8 bit address) 3. Initiate a serial interface cycle specifying the address of the register (A6 to A0) whose content has to be written 4. Write 16bit data which is latched on the rising edge of SCLK SCLK SDENB SDIO RWB A6 A5 Read = 1 Write = 0 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 7 bit address space 16bit data: D15 is MSB, D0 is LSB Figure 38. Serial Register Write Timing Diagram PARAMETER MIN MAX UNIT 20 MHz fSCLK SCLK frequency (equal to 1/tSCLK) tSLOADS SDENB to SCLK setup time 25 ns tSLOADH SCLK to SDENB hold time 25 ns tDSU SDIO setup time 25 ns tDH SDIO hold time 25 ns (1) 26 >DC TYP (1) Typical values at +25°C; minimum and maximum values across the full temperature range: TMIN = –40°C to TMAX = +85°C, AVDD3V = 3.3V, AVDD, DRVDD = 1.9V, unless otherwise noted. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 Serial Register Readout The device includes a mode where the contents of the internal registers can be read back using the SDO/SDIO pins. This read-back mode may be useful as a diagnostic check to verify the serial interface communication between the external controller and the ADC. 1. Drive SDENB pin low 2. Set the RW bit (A7) to '1'. This setting disables any further writes to the registers 3. Initiate a serial interface cycle specifying the address of the register (A6 to A0) whose content has to be read. 4. The device outputs the contents (D15 to D0) of the selected register on the SDO/SDIO pin 5. The external controller can latch the contents at the SCLK rising edge. 6. To enable register writes, reset the RW register bit to '0'. SCLK SDENB SDIO RWB Read = 1 Write = 0 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 7 bit address space 16bit data: D15 is MSB, D0 is LSB Figure 39. Serial Register Read Timing Diagram Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 27 ADS5404 SLAS945 – APRIL 2013 www.ti.com SERIAL REGISTER MAP (2) (2) Multiple functions in a register can be programmed in a single write operation. Register Address A7–A0 IN HEX Register Data D15 D14 D13 D12 0 3/4 Wire SPI Decimat ion Filter EN 0 ChA High/ Low Pass 1 ChA Corr EN 0 0 2 0 0 0 Start Auto Corr ChA 3 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 ChB High/ Low Pass 0 0 0 0 0 0 0 0 0 0 0 0 ChB Corr EN 0 0 0 0 0 Data Format 0 Hp Mode1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 Over-range threshold E Sync Select F Sync Select 1A 0 Start Auto Corr ChB 2B 0 0 0 0 1 0 1 0 0 0 0 0 VREF Set 0 0 1 Temp Sensor 2C Reset 37 Sleep Modes 38 3A 0 0 0 0 HP Mode2 LVDS Current Strength Internal LVDS Termination LVDS SW 0 0 0 0 0 0 BIAS EN SYNC EN LP Mode 1 0 0 0 0 0 DACLK EN DBCLK EN 0 OVRA EN OVRB EN D3 0 D2 0 0 0 66 LVDS Output Bus A EN 67 LVDS Output Bus B EN DESCRIPTION OF SERIAL INTERFACE REGISTERS Register Address A7-A0 in hex 0 Register Data D15 3/4 Wire SPI D14 Deci matio n Filter EN D13 0 D12 ChA High/ Low Pass D11 0 D10 0 D9 ChB High/ Low Pass D8 0 D7 0 D6 0 D5 0 D4 0 D15 3/4 Wire SPI Default 0 0 3 wire SPI is used with SDIO pin operating as bi-directional I/O port 1 4 wire SPI is used with SDIO pin operating as data input and SDO pin as data output port. D14 Decimation Filter EN Default 0 0 Normal operation with data output at full sampling rate 1 2x decimation filter enabled D12 ChA High/Low Pass Default 0 0 Low Pass 28 D1 0 D0 0 Enables 4-bit serial interface when set 2x decimation filter is enabled when bit is set (Decimation filter must be enabled first: set bit D14) Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 1 High Pass D9 ChB High/Low Pass Default 0 0 Low Pass 1 High Pass Register Address A7-A0 in hex 1 (Decimation filter must be enabled first: set bit D14) Register Data D15 ChA Corr EN D14 1 D13 0 D12 0 D11 0 D10 0 D9 ChB Corr EN D8 0 D7 0 D6 0 D15 ChA Corr EN (should be enabled for maximum performance) Default 0 0 auto correction disabled 1 auto correction enabled D9 ChB Corr EN (should be enabled for maximum performance) Default 0 0 auto correction disabled 1 auto correction enabled D3 Data Format Default 0 0 Two's complement 1 Offset Binary D1 HP Mode 1 Default 0 1 Must be set to 1 for optimum performance D5 0 D4 0 D3 Data Format D2 0 D1 HP Mode1 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 D0 0 29 ADS5404 SLAS945 – APRIL 2013 Register Address A7-A0 in hex 2 www.ti.com Register Data D15 D14 D13 D12 D11 0 0 0 0 0 D14 Read back 1. D10-D7 Over-range threshold D10 D9 D8 D7 Over-range threshold D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 The over-range detection is triggered 12 output clock cycles after the overload condition occurs. The threshold at which the OVR is triggered = 1.0V x [decimal value of <Over-range threshold>]/16. After power up or reset, the default value is 15 (decimal) which corresponds to a OVR threshold of 0.56dB below fullscale (20*log(15/16)). This OVR threshold is applicable to both channels. Default 1111 OVR Detection Threshold 0 Thresholds set to dBFS -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 Programmed Value (1-15) Register Address A7-A0 in hex 3 D14 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 Start Auto Corr ChA 0 0 1 0 1 1 0 0 0 1 1 0 0 0 Start Auto Corr ChA Starts DC offset and gain correction loop for ChA Default 1 Starts the DC offset and gain correction loop Clears the DC offset correction value to 0 and gain value to 1 0 1 D11, 9, 8, 4, 3 30 Register Data Must be set to 1 for maximum performance Default 1 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com SLAS945 – APRIL 2013 Register Address A7-A0 in hex E Register Data D15 0000 0000 0000 00 0101 0101 0101 01 1010 1010 1010 10 1111 1111 1111 11 Register Address A7-A0 in hex D6-D4 000 001 010 011 100 Others D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D4 D3 D2 D1 D0 0 0 0 0 Sync Select Sync selection for the clock generator block (also Default 1010 1010 need to see address 0x0F) 1010 10 Sync is disabled Sync is set to one shot (one time synchronization only) Sync is derived from SYNC input pins not supported Register Data D15 F 0000 0101 1010 1111 D13 Sync Select D15-D2 D15-D12 D14 D14 D13 D12 Sync Select D11 D10 D9 D8 D7 0 0 0 0 0 D6 D5 VREF Sel Sync Select Sync selection for the clock generator block Default 1010 Sync is disabled Sync is set to one shot (one time synchronization only) Sync is derived from SYNC input pins not supported VREF SEL Default 000 1.0V 1.25V 0.9V 0.8V 1.15V external reference Register Address A7-A0 in hex 1A D14 0 1 D11, 9, 8, 4, 3 Internal voltage reference selection Register Data D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 Start Auto Corr ChB 0 0 1 0 1 1 0 0 0 1 1 0 0 0 Start Auto Corr ChB Starts DC offset and gain correction loop for ChB Default 1 Starts the DC offset and gain correction loops Clears DC offset correction value to 0 and gain value to 1 Must be set to 1 for maximum performance Default 1 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 31 ADS5404 SLAS945 – APRIL 2013 Register Address A7-A0 in hex 2B D8-D0 www.ti.com Register Data D15 D14 D13 D12 D11 D10 D9 0 0 0 0 0 0 0 Temp Sensor Register Address A7-A0 in hex 2C D15 D14 000000 100000 110000 110101 32 D6 D5 D4 D3 D2 D1 D0 Temp Sensor Internal temperature sensor value – read only D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Reset Reset Default 0000 1101001011110000 D15-D14 D7 Register Data D15-D0 Register Address A7-A0 in hex 37 D8 This is a software reset to reset all SPI registers to their default value. Self clears to 0. Perform software reset Register Data D15 D14 D13 D12 D11 D10 Sleep Modes Sleep Modes Default 00 Complete shut down Stand-by mode Deep sleep mode Light sleep mode D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 Sleep mode selection which is controlled by the ENABLE pin. Sleep modes are active when ENABLE pin goes low. Wake Wake Wake Wake up up up up time 2.5 ms time 100 µs time 20 µs time 2 µs Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com Register Address A7-A0 in hex 38 SLAS945 – APRIL 2013 Register Data D15 D14 D13 D12 D11 D10 D9 D8 D7 HP Mode 2 D6 Bias EN D5 D4 SYNC LP EN Mode 1 D3 D2 D1 D0 0 0 0 0 D15-D7 HP Mode 2 Default 111111111 1 Set to 1 for normal operation D6 BIAS EN Default 1 Internal bias powered down Internal bias enabled Enables internal fuse bias voltages – can be disabled after power up to save power. D5 SYNC EN Default 1 Enables the SYNC input buffer. 0 SYNC input buffer disabled SYNC input bffer enabled 0 1 1 D4 0 1 LP Mode 1 Default 1 Internal input buffer disabled Internal input buffer disabled Low power mode 1 to disable unused internal input buffers. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 33 ADS5404 SLAS945 – APRIL 2013 Register Address A7-A0 in hex 3A D15-D13 000 001 010 011 D12-D11 01 11 D10-D9 00 01 10 11 D4 0 1 D3 0 1 D1 0 1 D0 0 1 34 www.ti.com Register Data D15 D14 D13 LVDS Current Strength LVDS Current Strength Default 000 2 mA 2.25 mA 2.5 mA 2.75 mA D12 D11 LVDS SW D10 D9 Internal LVDS Termination D8 0 D7 0 D6 0 D5 0 D4 DACLK EN D3 DBCLK EN D2 0 D1 OVRA EN D0 OVRB EN LVDS output current strength. 100 101 110 111 3 mA 3.25 mA 3.5 mA 3.75 mA LVDS SW LVDS driver internal switch setting – correct range must be set for setting in D15-D13 Default 01 2 mA to 2.75 mA 3mA to 3.75mA Internal LVDS Internal termination Termination Default 00 2 kΩ 200 Ω 200 Ω 100 Ω DACLK EN Enable DACLK output buffer Default 1 DACLK output buffer powered down DACLK output buffer enabled DBCLK EN Enable DBCLK output buffer Default 1 DBCLK output buffer powered down DBCLK output buffer enabled OVRA EN Enable OVRA output buffer Default 1 OVRA output buffer powered down OVRA output buffer enabled OVRB EN Enable OVRB output buffer Default 1 OVRB output buffer powered down OVRB output buffer enabled Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 ADS5404 www.ti.com Register Address A7-A0 in hex 66 D15-D10 0 1 D15 D14 D13 D12 D11-D10 Register Address A7-A0 in hex 67 D15-D10 0 1 D15 D14 D13 D12 D11-D10 SLAS945 – APRIL 2013 Register Data D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D4 D3 D2 D1 D0 LVDS Output Bus A EN LVDS Output Bus A EN Default FFFF Output is powered down Output is enabled Individual LVDS output pin power down for channel A Pins N7, P7 (no connect pins) which are not used and should be powered down for power savings Pins N6, P6 (no connect pins) which are not used and should be powered down for power savings SYNCOUTP/N (pins P5, N5) Pins N4, P4 (no connect pins) which are not used and should be powered down for power savings corresponds to DA11-DA0 Register Data D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 LVDS Output Bus B EN LVDS Output Bus B EN Default FFFF Output is powered down Output is enabled Individual LVDS output pin power down for channel B Pins G3, G4 (no connect pins) which are not used and should be powered down for power savings Pins F3, F4 (no connect pins) which are not used and should be powered down for power savings SYNCOUTP/N (pins F1, F2) Pins E3, E4 (no connect pins) which are not used and should be powered down for power savings corresponds to DB11-DB0 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS5404 35 PACKAGE OPTION ADDENDUM www.ti.com 28-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) ADS5404IZAY ACTIVE NFBGA ZAY 196 160 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR -40 to 85 ADS5404I ADS5404IZAYR ACTIVE NFBGA ZAY 196 1000 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR -40 to 85 ADS5404I (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADS5404IZAYR Package Package Pins Type Drawing NFBGA ZAY 196 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 330.0 24.4 Pack Materials-Page 1 12.3 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 12.3 2.3 16.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS5404IZAYR NFBGA ZAY 196 1000 336.6 336.6 31.8 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated