Order this document by BCP68T1/D SEMICONDUCTOR TECHNICAL DATA Motorola Preferred Device This NPN Silicon Epitaxial Transistor is designed for use in low voltage, high current applications. The device is housed in the SOT-223 package, which is designed for medium power surface mount applications. MEDIUM POWER NPN SILICON HIGH CURRENT TRANSISTOR SURFACE MOUNT • High Current: IC = 1.0 Amp • The SOT-223 Package can be soldered using wave or reflow. • SOT-223 package ensures level mounting, resulting in improved thermal conduction, and allows visual inspection of soldered joints. The formed leads absorb thermal stress during soldering, eliminating the possibility of damage to the die • Available in 12 mm Tape and Reel Use BCP68T1 to order the 7 inch/1000 unit reel. Use BCP68T3 to order the 13 inch/4000 unit reel. • The PNP Complement is BCP69T1 4 1 COLLECTOR 2,4 2 3 CASE 318E-04, STYLE 1 TO-261AA BASE 1 EMITTER 3 MAXIMUM RATINGS (TC = 25°C unless otherwise noted) Rating Symbol Value Unit Collector-Emitter Voltage VCEO 25 Vdc Collector-Base Voltage VCBO 20 Vdc Emitter-Base Voltage VEBO 5 Vdc Collector Current IC 1 Adc Total Power Dissipation @ TA = 25°C(1) Derate above 25°C PD 1.5 12 Watts mW/°C TJ, Tstg – 65 to 150 °C Symbol Max Unit RθJA 83.3 °C/W TL 260 10 °C Sec Operating and Storage Temperature Range DEVICE MARKING CA THERMAL CHARACTERISTICS Characteristic Thermal Resistance — Junction-to-Ambient (surface mounted) Maximum Temperature for Soldering Purposes Time in Solder Bath 1. Device mounted on a FR-4 glass epoxy printed circuit board 1.575 in. x 1.575 in. x 0.0625 in.; mounting pad for the collector lead = 0.93 sq. in. Thermal Clad is a trademark of the Bergquist Company Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 Small–Signal Motorola Motorola, Inc. 1996 Transistors, FETs and Diodes Device Data 1 BCP68T1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Symbol Min Typ Max Unit Collector-Emitter Breakdown Voltage (IC = 100 µAdc, IE = 0) V(BR)CES 25 — — Vdc Collector-Emitter Breakdown Voltage (IC = 1.0 mAdc, IB = 0) V(BR)CEO 20 — — Vdc Emitter-Base Breakdown Voltage (IE = 10 µAdc, IC = 0) V(BR)EBO 5.0 — — Vdc Collector-Base Cutoff Current (VCB = 25 Vdc, IE = 0) ICBO — — 10 µAdc Emitter-Base Cutoff Current (VEB = 5.0 Vdc, IC = 0) IEBO — — 10 µAdc 50 85 60 — — — — 375 — Characteristics OFF CHARACTERISTICS ON CHARACTERISTICS (2) DC Current Gain (IC = 5.0 mAdc, VCE = 10 Vdc) (IC = 500 mAdc, VCE = 1.0 Vdc) (IC = 1.0 Adc, VCE = 1.0 Vdc) hFE — Collector-Emitter Saturation Voltage (IC = 1.0 Adc, IB = 100 mAdc) VCE(sat) — — 0.5 Vdc Base-Emitter On Voltage (IC = 1.0 Adc, VCE = 1.0 Vdc) VBE(on) — — 1.0 Vdc fT — 60 — MHz DYNAMIC CHARACTERISTICS Current-Gain — Bandwidth Product (IC = 10 mAdc, VCE = 5.0 Vdc) 2. Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2.0% 300 200 TJ = 125°C = 25°C 100 = – 55°C VCE = 1.0 V 10 1.0 10 100 IC, COLLECTOR CURRENT (mA) Figure 1. DC Current Gain 2 1000 f T, CURRENT-GAIN-BANDWIDTH PRODUCT (MHz) hFE, DC CURRENT GAIN TYPICAL ELECTRICAL CHARACTERISTICS 300 200 100 70 VCE = 10 V TJ = 25°C f = 30 MHz 50 30 10 100 200 IC, COLLECTOR CURRENT (mA) 1000 Figure 2. Current-Gain-Bandwidth Product Motorola Small–Signal Transistors, FETs and Diodes Device Data BCP68T1 TYPICAL ELECTRICAL CHARACTERISTICS 80 TJ = 25°C TJ = 25°C 0.8 VBE(sat) @ IC/IB = 10 0.6 VBE(on) @ VCE = 1.0 V 70 Cib, CAPACITANCE (pF) V, VOLTAGE (VOLTS) 1.0 0.4 0.2 0 50 40 VCE(sat) @ IC/IB = 10 1.0 60 30 10 100 1000 IC, COLLECTOR CURRENT (mA) 0 1.0 Figure 3. “On” Voltage Figure 4. Capacitance RθVB, TEMPERATURE COEFFICIENT (mV/°C) 25 Cob, CAPACITANCE (pF) TJ = 25°C 20 15 10 5.0 0 5.0 2.0 3.0 4.0 VR, REVERSE VOLTAGE (VOLTS) 5.0 10 15 VR, REVERSE VOLTAGE (VOLTS) 20 – 0.8 –1.2 –1.6 RθVB for VBE – 2.0 – 2.4 – 2.8 1.0 Figure 5. Capacitance 10 100 IC, COLLECTOR CURRENT (mA) 1000 Figure 6. Base-Emitter Temperature Coefficient 1.0 VCE , COLLECTOR VOLTAGE (V) TJ = 25°C 0.8 0.6 0.4 = 1000 mA I C = 10 mA = 50 mA = 100 mA 0.2 0 0.01 = 500 mA 0.1 1.0 10 IB, BASE CURRENT (mA) 100 Figure 7. Saturation Region Motorola Small–Signal Transistors, FETs and Diodes Device Data 3 BCP68T1 INFORMATION FOR USING THE SOT-223 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection 0.15 3.8 0.079 2.0 0.091 2.3 0.248 6.3 0.091 2.3 0.079 2.0 0.059 1.5 0.059 1.5 0.059 1.5 inches mm SOT-223 SOT-223 POWER DISSIPATION PD = TJ(max) – TA RθJA 140 Board Material = 0.0625″ G-10/FR-4, 2 oz Copper TA = 25°C 0.8 Watts 1.25 Watts* θ 150°C – 25°C = 1.5 watts 83.3°C/W 1.5 Watts 100 80 0.0 The 83.3°C/W for the SOT-223 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 1.5 watts. There are other alternatives to achieving higher power dissipation from the SOT-223 package. One is to increase the area of the collector pad. By increasing the area of the collector pad, the 4 160 ° 120 The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 1.5 watts. PD = power dissipation can be increased. Although the power dissipation can almost be doubled with this method, area is taken up on the printed circuit board which can defeat the purpose of using surface mount technology. A graph of RθJA versus collector pad area is shown in Figure 8. R JA , Thermal Resistance, Junction to Ambient ( C/W) The power dissipation of the SOT-223 is a function of the collector pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-223 package, PD can be calculated as follows: *Mounted on the DPAK footprint 0.2 0.4 0.6 A, Area (square inches) 0.8 1.0 Figure 8. Thermal Resistance versus Collector Pad Area for the SOT-223 Package (Typical) Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. Motorola Small–Signal Transistors, FETs and Diodes Device Data BCP68T1 SOLDER STENCIL GUIDELINES Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. A solder stencil is required to screen the optimum amount of solder paste onto the footprint. The stencil is made of brass or stainless steel with a typical thickness of 0.008 inches. The stencil opening size for the SOT-223 package should be the same as the pad size on the printed circuit board, i.e., a 1:1 registration. SOLDERING PRECAUTIONS The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference should be a maximum of 10°C. • The soldering temperature and time should not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient should be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. TYPICAL SOLDER HEATING PROFILE For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones, and a figure for belt speed. Taken together, these control settings make up a heating “profile” for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 9 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. The line on the graph shows the STEP 1 PREHEAT ZONE 1 “RAMP” 200°C STEP 2 STEP 3 VENT HEATING “SOAK” ZONES 2 & 5 “RAMP” DESIRED CURVE FOR HIGH MASS ASSEMBLIES 150°C actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177 –189°C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints. STEP 5 STEP 6 STEP 7 STEP 4 HEATING VENT COOLING HEATING ZONES 3 & 6 ZONES 4 & 7 205° TO “SPIKE” “SOAK” 219°C 170°C PEAK AT SOLDER 160°C JOINT 150°C 100°C 140°C 100°C SOLDER IS LIQUID FOR 40 TO 80 SECONDS (DEPENDING ON MASS OF ASSEMBLY) DESIRED CURVE FOR LOW MASS ASSEMBLIES 50°C TIME (3 TO 7 MINUTES TOTAL) TMAX Figure 9. Typical Solder Heating Profile Motorola Small–Signal Transistors, FETs and Diodes Device Data 5 BCP68T1 PACKAGE DIMENSIONS A F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 4 S B 1 2 3 D L G J C 0.08 (0003) M H K INCHES DIM MIN MAX A 0.249 0.263 B 0.130 0.145 C 0.060 0.068 D 0.024 0.035 F 0.115 0.126 G 0.087 0.094 H 0.0008 0.0040 J 0.009 0.014 K 0.060 0.078 L 0.033 0.041 M 0_ 10 _ S 0.264 0.287 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 6.30 6.70 3.30 3.70 1.50 1.75 0.60 0.89 2.90 3.20 2.20 2.40 0.020 0.100 0.24 0.35 1.50 2.00 0.85 1.05 0_ 10 _ 6.70 7.30 BASE COLLECTOR EMITTER COLLECTOR CASE 318E–04 ISSUE H TO-261AA Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] – TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 6 ◊ *BCP68T1/D* Motorola Small–Signal Transistors, FETs and Diodes Device Data BCP68T1/D