19-5503; Rev 9/10 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs www.maxim-ic.com FEATURES Integrated NV SRAM, Real-Time Clock, Crystal, Power-Fail Control Circuit, and Lithium Energy Source Clock Registers are Accessed Identically to the Static RAM. These Registers are Resident in the Eight Top RAM Locations. Century Byte Register (i.e., Y2K Compliant) Totally Nonvolatile with Over 10 Years of Operation in the Absence of Power BCD-Coded Century, Year, Month, Date, Day, Hours, Minutes, and Seconds with Automatic Leap Year Compensation Valid Up to the Year 2100 Battery Voltage-Level Indicator Flag Power-Fail Write Protection Allows for ±10% VCC Power Supply Tolerance Lithium Energy Source is Electrically Disconnected to Retain Freshness Until Power is Applied for the First Time DIP Module Only Standard JEDEC Byte-Wide 128k x 8 Static RAM Pinout PowerCap Module Board Only Surface Mountable Package for Direct Connection to PowerCap Containing Battery and Crystal Replaceable Battery (PowerCap) Power-On Reset Output Pin-for-Pin Compatible with Other Densities of DS174xP Timekeeping RAM Also Available in Industrial Temperature Range: -40°C to +85°C Underwriters Laboratories (UL) recognized PIN CONFIGURATIONS TOP VIEW N.C. A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 1 Maxim 2 DS1746 3 4 5 6 7 8 9 10 11 12 32 31 30 29 28 27 26 25 24 23 22 21 VCC A15 N.C. WE A13 A8 A9 A11 OE A10 CE DQ0 13 20 DQ6 DQ1 DQ2 14 19 DQ5 15 18 DQ4 GND 16 17 DQ3 A0 DQ7 Encapsulated DIP N.C. A15 A16 RST VCC WE OE CE DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Maxim DS1746P X1 GND VBAT X2 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 N.C. N.C. A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 PowerCap Module Board (Uses DS9034PCX PowerCap) Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata. 1 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs PIN DESCRIPTION PDIP 1, 30 2 3 4 5 6 7 8 9 10 11 12 23 25 26 27 28 31 13 14 15 17 18 19 20 21 16 22 24 29 32 PIN PowerCap 1, 33, 34 3 32 30 25 24 23 22 21 20 19 18 28 29 27 26 31 2 16 15 14 13 12 11 10 9 17 8 7 6 5 — 4 — FUNCTION NAME N.C. A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 A10 A11 A9 A8 A13 A15 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 GND CE OE WE VCC RST X1, X2, VBAT No Connection Address Input Data Input/Output Ground Active-Low Chip Enable Input Active-Low Output Enable Input Active-Low Write-Enable Input Power-Supply Input Active-Low Power-Fail Output, Open Drain. Requires a pullup resistor for proper operation. Crystal Connection, VBAT Battery Connection. UL recognized to ensure against reverse charging when used with a lithium battery. www.maximic.com/qa/info/ul/ 2 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs ORDERING INFORMATION PART DS1746-70+ DS1746-70IND+ DS1746P-70+ DS1746P-70IND+ DS1746W-120+ DS1746W-120IND+ DS1746WP-120+ DS1746WP-120IND+ VOLTAGE RANGE (V) 5.0 5.0 5.0 5.0 3.3 3.3 3.3 3.3 TEMP RANGE PIN-PACKAGE TOP MARK† 0°C to +70°C -40°C to +85°C 0°C to +70°C -40°C to +85°C 0°C to +70°C -40°C to +85°C 0°C to +70°C -40°C to +85°C 32 EDIP (0.740a) 32 EDIP (0.740a) 34 PowerCap* 34 PowerCap* 32 EDIP (0.740a) 32 EDIP (0.740a) 34 PowerCap* 34 PowerCap* DS1746+070 DS1746+070 IND DS1746P+70 DS1746P+070 IND DS1746W+120 DS1746W+120 IND DS1746WP+120 DS1746WP+120 IND +Denotes a lead(Pb)-free/RoHS-compliant package. The top mark will include a “+” symbol on lead-free devices. *DS9034-PCX+ or DS9034I-PCX+ required (must be ordered separately). † An “IND” anywhere on the top mark denotes an industrial temperature grade device. DESCRIPTION The DS1746 is a full-function, year-2000-compliant (Y2KC), real-time clock/calendar (RTC) and 128k x 8 nonvolatile static RAM. User access to all registers within the DS1746 is accomplished with a byte-wide interface as shown in Figure 1. The RTC information and control bits reside in the eight uppermost RAM locations. The RTC registers contain century, year, month, date, day, hours, minutes, and seconds data in 24-hour binary-coded decimal (BCD) format. Corrections for the date of each month and leap year are made automatically. The RTC clock registers are double buffered to avoid access of incorrect data that can occur during clock update cycles. The double-buffered system also prevents time loss as the timekeeping countdown continues unabated by access to time register data. The DS1746 also contains its own power-fail circuitry, which deselects the device when the VCC supply is in an out of tolerance condition. This feature prevents loss of data from unpredictable system operation brought on by low VCC as errant access and update cycles are avoided. 3 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs Figure 1. Block Diagram PACKAGES The DS1746 is available in two packages (32-pin DIP and 34-pin PowerCap module). The 32-pin DIP style module integrates the crystal, lithium energy source, and silicon all in one package. The 34-pin PowerCap Module Board is designed with contacts for connection to a separate PowerCap (DS9034PCX) that contains the crystal and battery. This design allows the PowerCap to be mounted on top of the DS1746P after the completion of the surface mount process. Mounting the PowerCap after the surface mount process prevents damage to the crystal and battery due to the high temperatures required for solder reflow. The PowerCap is keyed to prevent reverse insertion. The PowerCap Module Board and PowerCap are ordered separately and shipped in separate containers. The part number for the PowerCap is DS9034PCX. CLOCK OPERATIONS—READING THE CLOCK While the double-buffered register structure reduces the chance of reading incorrect data, internal updates to the DS1746 clock registers should be halted before clock data is read to prevent reading of data in transition. However, halting the internal clock register updating process does not affect clock accuracy. Updating is halted when a one is written into the read bit, bit 6 of the century register (see Table 2). As long as a one remains in that position, updating is halted. After a halt is issued, the registers reflect the count, that is day, date, and time that was current at the moment the halt command was issued. However, the internal clock registers of the double-buffered system continue to update so that the clock accuracy is not affected by the access of data. All of the DS1746 registers are updated simultaneously after the internal clock register updating process has been re-enabled. Updating is within a second after the read bit is written to zero. The READ bit must be a zero for a minimum of 500s to ensure the external registers will be updated. 4 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs Table 1. Truth Table VCC VCC>VPF VSO<VCC<VPF VCC<VSO<VPF CE OE WE VIH VIL VIL VIL X X X X VIL VIH X X X VIL VIH VIH X X MODE Deselect Write Read Read Deselect Deselect DQ High-Z Data In Data Out High-Z High-Z High-Z POWER Standby Active Active Active CMOS Standby Data-Retention Mode SETTING THE CLOCK As shown in Table 2, bit 7 of the century register is the write bit. Setting the write bit to a one, like the read bit, halts updates to the DS1746 registers. The user can then load them with the correct day, date and time data in 24 hour BCD format. Resetting the write bit to a zero then transfers those values to the actual clock counters and allows normal operation to resume. STOPPING AND STARTING THE CLOCK OSCILLATOR The clock oscillator may be stopped at any time. To increase the shelf life, the oscillator can be turned off to minimize current drain from the battery. The OSC bit is the MSB (bit 7) of the seconds registers (see Table 2). Setting it to a one stops the oscillator. FREQUENCY TEST BIT As shown in Table 2, bit 6 of the day byte is the frequency test bit. When the frequency test bit is set to logic “1” and the oscillator is running, the LSB of the seconds register will toggle at 512 Hz. When the seconds register is being read, the DQ0 line will toggle at the 512 Hz frequency as long as conditions for access remain valid (i.e., CE low, OE low, WE high, and address for seconds register remain valid and stable). CLOCK ACCURACY (DIP MODULE) The DS1746 is guaranteed to keep time accuracy to within 1 minute per month at 25C. The RTC is calibrated at the factory by Maxim using nonvolatile tuning elements, and does not require additional calibration. For this reason, methods of field clock calibration are not available and not necessary. The electrical environment also affects clock accuracy and caution should be taken to place the RTC in the lowest-level EMI section of the PC board layout. For additional information, refer to Application Note 58. CLOCK ACCURACY (PowerCap MODULE) The DS1746 and DS9034PCX are each individually tested for accuracy. Once mounted together, the module will typically keep time accuracy to within 1.53 minutes per month (35 ppm) at 25°C. The electrical environment also affects clock accuracy and caution should be taken to place the RTC in the lowest-level EMI section of the PC board layout. For additional information, refer to Application Note 58. 5 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs Table 2. Register Map ADDRESS 1FFFF 1FFFE 1FFFD 1FFFC 1FFFB 1FFFA 1FFF9 1FFF8 DATA B7 B6 X X BF X X OSC W X X FT X B5 B4 B3 10 Year R B2 B1 Year Month Date X 10 Month 10 Date X X 10 Hour 10 Minutes 10 Seconds 10 Century X Day Hour Minutes Seconds Century OSC = Stop Bit R = Read Bit FT = Frequency Test W = Write Bit X = See Note BF = Battery Flag B0 FUNCTION RANGE Year Month Date Day Hour Minutes Seconds Century 00-99 01-12 01-31 01-07 00-23 00-59 00-59 00-39 Note: All indicated “X” bits are not used but must be set to “0” during a write cycle to ensure proper clock operation. RETRIEVING DATA FROM RAM OR CLOCK The DS1746 is in the read mode whenever OE (output enable) is low, WE (write enable) is high, and CE (chip enable) is low. The device architecture allows ripple-through access to any of the address locations in the NV SRAM. Valid data will be available at the DQ pins within tAA after the last address input is stable, providing that the CE and OE access times and states are satisfied. If CE or OE access times and states are not met, valid data will be available at the latter of chip enable access (tCEA) or at output enable access time (tOEA). The state of the data input/output pins (DQ) is controlled by CE and OE. If the outputs are activated before tAA, the data lines are driven to an intermediate state until tAA . If the address inputs are changed while CE and OE remain valid, output data will remain valid for output data hold time (tOH) but will then go indeterminate until the next address access. WRITING DATA TO RAM OR CLOCK The DS1746 is in the write mode whenever WE, and CE are in their active state. The start of a write is referenced to the latter occurring transition of WE, or CE. The addresses must be held valid throughout the cycle. CE or WE must return inactive for a minimum of tWR prior to the initiation of another read or write cycle. Data in must be valid tDS prior to the end of write and remain valid for tDS afterward. In a typical application, the OE signal will be high during a write cycle. However, OE can be active provided that care is taken with the data bus to avoid bus contention. If OE is low prior to WE transitioning low the data bus can become active with read data defined by the address inputs. A low transition on WE will then disable the output tWEZ after WE goes active. 6 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs DATA-RETENTION MODE The 5V device is fully accessible and data can be written or read only when VCC is greater than VPF. However, when VCC is below the power-fail point, VPF, (point at which write protection occurs) the internal clock registers and SRAM are blocked from any access. At this time the power fail reset output signal (RST) is driven active and will remain active until VCC returns to nominal levels. When VCC falls below the battery switch point VSO (battery supply level), device power is switched from the VCC pin to the backup battery. RTC operation and SRAM data are maintained from the battery until VCC is returned to nominal levels. The 3.3V device is fully accessible and data can be written or read only when VCC is greater than VPF. When VCC falls below the power fail point, VPF, access to the device is inhibited. At this time the power fail reset output signal (RST) is driven active and will remain active until VCC returns to nominal levels. If VPF is less than VSO, the device power is switched from VCC to the backup supply (VBAT) when VCC drops below VPF. If VPF is greater than VSO, the device power is switched from VCC to the backup supply (VBAT) when VCC drops below VSO. RTC operation and SRAM data are maintained from the battery until VCC is returned to nominal levels. The RST signal is an open drain output and requires a pull up. Except for the RST, all control, data, and address signals must be powered down when VCC is powered down. BATTERY LONGEVITY The DS1746 has a lithium power source that is designed to provide energy for clock activity, and clock and RAM data retention when the VCC supply is not present. The capability of this internal power supply is sufficient to power the DS1746 continuously for the life of the equipment in which it is installed. For specification purposes, the life expectancy is 10 years at 25C with the internal clock oscillator running in the absence of VCC power. Each DS1746 is shipped from Maxim with its lithium energy source disconnected, guaranteeing full energy capacity. When VCC is first applied at a level greater than VPF, the lithium energy source is enabled for battery backup operation. Actual life expectancy of the DS1746 will be much longer than 10 years since no lithium battery energy is consumed when VCC is present. BATTERY MONITOR The DS1746 constantly monitors the battery voltage of the internal battery. The Battery Flag bit (bit 7) of the day register is used to indicate the voltage level range of the battery. This bit is not writable and should always be a one when read. If a zero is ever present, an exhausted lithium energy source is indicated and both the contents of the RTC and RAM are questionable. 7 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground..………………………………..……………………..-0.3V to +6.0V Storage Temperature Range EDIP ...................................................……………………...………………..……………….-40°C to +85°C PowerCap ................................................................................................................………...-55°C to +125°C Lead Temperature (soldering, 10s)…........................................................................................……………….+260°C Note: EDIP is hand or wave-soldered only. Soldering Temperature (reflow, PowerCap)......................................................................................…………+260°C This is a stress rating only and functional operation of the device at these or any other condition above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. OPERATING RANGE RANGE Commercial Industrial TEMP RANGE 0°C to +70°C, Noncondensing -40°C to +85°C, Noncondensing VCC 3.3V 10% or 5V 10% 3.3V 10% or 5V 10% RECOMMENDED DC OPERATING CONDITIONS (TA = Over the Operating Range) PARAMETER Logic 1 Voltage All Inputs VCC = 5V 10% VCC = 3.3V 10% Logic 0 Voltage All Inputs VCC = 5V 10% VCC = 3.3V 10% SYMBOL MIN VIH 2.2 VIH 2.0 VIL VIL TYP MAX VCC + 0.3V VCC + 0.3V UNITS NOTES V 1 V 1 -0.3 0.8 V 1 -0.3 0.6 V 1 MAX 85 UNITS mA NOTES 2, 3, 10 Icc1 6 mA 2, 3 Icc2 4 mA 2, 3 DC ELECTRICAL CHARACTERISTICS (VCC = 5.0V 10%, TA = Over the Operating Range.) PARAMETER Active Supply Current TTL Standby Current ( CE = VIH) CMOS Standby Current ( CE VCC-0.2V) Input Leakage Current (any input) SYMBOL Icc MIN TYP IIL -1 +1 A +1 A Output Leakage Current (any output) Output Logic 1 Voltage (IOUT = -1.0 mA) Output Logic 0 Voltage (IOUT = +2.1 mA) IOL -1 VOH 2.4 Write Protection Voltage VPF Battery Switchover Voltage VSO 1 0.4 VOL 4.25 4.50 VBAT 8 of 16 1 V 1 1, 4 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs DC ELECTRICAL CHARACTERISTICS (VCC = 3.3V 10%, TA = Over the Operating Range.) PARAMETER Active Supply Current TTL Standby Current ( CE = VIH) CMOS Standby Current ( CE VCC-0.2V) SYMBOL MIN TYP MAX UNITS NOTES Icc 30 mA 2, 3, 10 Icc1 2 mA 2, 3 Icc2 2 mA 2, 3 Input Leakage Current (any input) IIL -1 +1 A Output Leakage Current (any output) IOL -1 +1 A Output Logic 1 Voltage (IOUT = -1.0 mA) VOH 2.4 Output Logic 0 Voltage (IOUT = +2.1 mA) VOL Write Protection Voltage VPF Battery Switchover Voltage VSO 1 0.4 2.80 2.97 1 V 1 V 1, 4 MAX UNITS ns NOTES 70 ns VBAT or VPF AC CHARACTERISTICS—READ CYCLE (5V) (VCC = 5.0V 10%, TA = Over the Operating Range.) PARAMETER Read Cycle Time SYMBOL tRC MIN 70 TYP Address Access Time tAA CE to DQ Low-Z tCEL CE Access Time tCEA 70 ns CE Data Off Time tCEZ 25 ns OE to DQ Low-Z tOEL OE Access Time tOEA 35 ns OE Data Off Time tOEZ 25 ns Output Hold from Address tOH 5 ns 5 5 9 of 16 ns ns DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs AC CHARACTERISTICS—READ CYCLE (3.3V) (VCC = 3.3V 10%, TA = Over the Operating Range.) PARAMETER SYMBOL MIN TYP Read Cycle Time tRC 120 Address Access Time tAA CE to DQ Low-Z tCEL CE Access Time tCEA 120 ns CE Data Off Time tCEZ 40 ns OE to DQ Low-Z tOEL OE Access Time tOEA 100 ns OE Data Off Time tOEZ 35 ns Output Hold from Address tOH 120 5 ns 5 ns tRC VALID tOH tCEZ tCEA CE tCEL tOEZ tOEA OE tOEL DQ0-DQ7 VALID 10 of 16 ns ns 5 tAA UNITS ns READ CYCLE TIMING DIAGRAM A0-A16 MAX NOTES DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs AC CHARACTERISTICS—WRITE CYCLE (5V) (VCC = 5.0V 10%, TA = Over the Operating Range.) PARAMETER SYMBOL MIN TYP MAX Write Cycle Time tWC 70 ns Address Setup Time tAS 0 ns WE Pulse Width tWEW 50 ns CE Pulse Width tCEW 60 ns Data Setup Time tDS 30 ns Data Hold Time tDH1 0 ns 8 Data Hold Time tDH2 0 ns 9 WE Data Off Time tWEZ Write Recovery Time tWR1 5 ns 8 Write Recovery Time tWR2 5 ns 9 UNITS NOTES 25 UNITS NOTES ns AC CHARACTERISTICS—WRITE CYCLE (3.3V) (VCC = 3.3V 10%, TA = Over the Operating Range.) PARAMETER SYMBOL MIN TYP MAX Write Cycle Time tWC 120 Address Setup Time tAS 0 WE Pulse Width tWEW 100 ns CE Pulse Width tCEW 110 ns CE and CE2 Pulse Width tCEW 110 ns Data Setup Time tDS 80 ns Data Hold Time tDH1 0 ns 8 Data Hold Time tDH2 0 ns 9 WE Data Off Time tWEZ Write Recovery Time tWR1 5 ns 8 Write Recovery Time tWR2 10 ns 9 ns 120 40 11 of 16 ns ns DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs WRITE CYCLE TIMING DIAGRAM, WRITE-ENABLE CONTROLLED tW C A0-A16 VALID CE tAS tWEW tWR1 WE tWEZ DQ0-DQ7 tDS DATA OUTPUT tDH1 DATA INPUT WRITE CYCLE TIMING DIAGRAM, CHIP-ENABLE CONTROLLED tWC A0-A16 VALID tAS tCEW tWR2 CE WE tDS DQ0-DQ7 tDH2 DATA INPUT 12 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs POWER-UP/DOWN AC CHARACTERISTICS—5V (VCC = 5.0V 10%, TA = Over the Operating Range.) PARAMETER CE or WE at VH Before Power-Down VCC Fall Time: VPF(MAX) to VPF(MIN) SYMBOL MIN tPD 0 s tF 300 s VCC Fall Time: VPF(MIN) to VSO tFB 10 s VCC Rise Time: VPF(MIN) to VPF(MAX) tR 0 s Power-Up Recover Time tREC Expected Data-Retention Time (Oscillator ON) tDR TYP MAX 35 10 POWER-UP/DOWN TIMING (5V DEVICE) 13 of 16 UNITS NOTES ms years 5, 6 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs POWER-UP/DOWN CHARACTERISTICS—3.3V (VCC = 3.3V 10%, TA = Over the Operating Range.) PARAMETER SYMBOL MIN CE or WE at VH, Before Power-Down VCC Fall Time: VPF(MAX) to VPF(MIN) VCC Rise Time: VPF(MIN) to VPF(MAX) tPD 0 s tF 300 s tR 0 s VPF to RST High Expected Data-Retention Time (Oscillator ON) tREC tDR TYP MAX 35 10 UNITS NOTES ms years 5, 6 POWER-UP/DOWN WAVEFORM TIMING (3.3V DEVICE) CAPACITANCE (TA = +25°C) PARAMETER Capacitance on All Input Pins Capacitance on All Output Pins SYMBOL CIN CO MIN 14 of 16 TYP MAX 14 10 UNITS pF pF NOTES DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs AC TEST CONDITIONS Output Load: 50pF + 1TTL Gate Input Pulse Levels: 0 to 3.0V Timing Measurement Reference Levels: Input: 1.5V Output: 1.5V Input Pulse Rise and Fall Times: 5ns NOTES: 1) 2) 3) 4) 5) 6) Voltages are referenced to ground. Typical values are at +25C and nominal supplies. Outputs are open. Battery switchover occurs at the lower of either the battery terminal voltage or VPF. Data-retention time is at +25C. Each DS1746 has a built-in switch that disconnects the lithium source until VCC is first applied by the user. The expected tDR is defined for DIP modules and assembled PowerCap modules as a cumulative time in the absence of VCC starting from the time power is first applied by the user. 7) RTC modules (DIP) can be successfully processed through conventional wave-soldering techniques as long as temperatures as long as temperature exposure to the lithium energy source contained within does not exceed +85C. Post-solder cleaning with water-washing techniques is acceptable, provided that ultra-sonic vibration is not used. In addition, for the PowerCap: a) Maxim recommends that PowerCap module bases experience one pass through solder reflow oriented with the label side up (“live-bug”). b) Hand soldering and touch-up: Do not touch or apply the soldering iron to leads for more than 3 seconds. To solder, apply flux to the pad, heat the lead frame pad, and apply solder. To remove the part, apply flux, heat the lead frame pad until the solder reflows, and use a solder wick to remove solder. 8) tWR1, tDH1 are measured from WE going high. 9) tWR2, tDH2 are measured from CE going high. 10) tWC = 200ns. PACKAGE INFORMATION For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. LAND PATTERN NO. 32 EDIP 34 PWRCP MDF32+1 PC2+6 21-0245 21-0246 — — 15 of 16 DS1746/DS1746P Y2K-Compliant, Nonvolatile Timekeeping RAMs REVISION HISTORY REVISION DATE 080508 9/10 DESCRIPTION PAGES CHANGED Added UL recognition information and weblink to the Pin Description table; corrected the top mark for –70 part numbers in the Ordering Information table; updated the write timing diagrams to show tWR as specified by RAM vendors 2, 3, 10, 12 Updated the Ordering Information table top mark information; updated the Absolute Maximum Ratings section to include the storage temperature range and lead and soldering temperatures for EDIP and PowerCap packages; added Note 10 to the ICC parameter in the DC Electrical Characteristics tables (for 5.0V and 3.3V) and the Notes section; updated the Package Information table 3, 8, 9, 15 16 of 16 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 2010 Maxim Integrated Products Maxim and the Dallas logo are registered trademarks of Maxim Integrated Products.