DIOTEC ELECTRONICS CORP. Data Sheet No. BRDB-1500P-1C ADBD-1500P-1C 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 15 AMP SILICON BRIDGE RECTIFIERS MECHANICAL SPECIFICATION FEATURES SERIES: DB1500P - DB1510P and ADB1504P - ADB1508P VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) Heat Sink Heat Sink BH BUILT-IN STRESS RELIEF MECHANISM FOR SUPERIOR RELIABILITY AND PERFORMANCE Molded Body INTEGRALLY MOLDED HEAT SINK PROVIDES VERY LOW THERMAL RESISTANCE FOR MAXIMUM HEAT DISSIPATION LT D1 UL RECOGNIZED - FILE #E124962 D1 HOLE FOR #10 SCREW HOLE FOR #10 SCREW (Nom. Hole Dia.=0.208") (Nom. Hole Dia.=0.208") AC D3 BL AC AC AC + _ AC BL D1 _ _ Case: Molded epoxy with integral heat sink Epoxy carries a U/L Flammability rating of 94V-0 LD + MECHANICAL DATA Molded Body LL AC + RoHS COMPLIANT BH D2 D1 BL BL Terminals: Round silver plated copper pins or fast-on terminals SYM MILLIMETERS 28.4 MAX 28.7 MIN Soldering: Per MIL-STD 202 Method 208 guaranteed (Note 1) BL D2 INCHES MIN SYM MILLIMETERS 28.4 MAX 28.7 MIN 1.12 MAX 1.13 BL INCHES MIN 1.12 MAX 1.13 0.40 Polarity: Marked on side of case BH 9.6 10.2 0.38 0.40 BH 9.6 10.2 0.38 D1 15.7 16.7 0.62 0.66 17.5 18.5 0.69 0.73 Mounting Position: Any. Through hole for #10 screw. Max. mounting torque = 20 in-lb. D2 D3 17.5 13.5 n/a 18.5 14.5 0.69 0.53 n/a 0.73 0.57 0.6 D1 D2 LL 10.9 20.6 11.9 n/a 0.47 n/a LD 1.0 1.1 0.43 0.81 0.039 LT Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams) Wire Leads - 0.55 Ounce (16.0 Grams) 15.2 Suffix "T" indicates FAST-ON TERMINALS 0.042 Suffix "W" indicates WIRE LEADS MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%. RATINGS PARAMETER (TEST CONDITIONS) SYMBOL CONTROLLED AVALANCHE ADB Series Number ADB ADB UNITS NON-CONTROLLED AVALANCHE DB DB DB DB DB DB DB 1504P 1506P 1508P 1500P 1501P 1502P 1504P 1506P 1508P 1510P Maximum DC Blocking Voltage VRM Working Peak Reverse Voltage VRWM Maximum Peak Recurrent Reverse Voltage VRRM RMS Reverse Voltage VR (RMS) Peak Forward Surge Current. Single 60Hz Half-Sine Wave o Superimposed on Rated Load (JEDEC Method). TJ = 125 C 400 600 800 50 100 200 400 600 800 1000 280 420 560 35 70 140 280 420 560 IFSM 400 IO 15 Junction Temperature Range TJ -55 to +150 Storage Temperature Range TSTG -55 to +150 Mimimum Avalanche Voltage V(BR) Min See Note 1 Maximum Avalanche Voltage V(BR) Max See Note 1 o Average Forward Rectified Current @ TC = 75 C VOLTS 700 AMPS °C n/a n/a VOLTS VFM 1.05 IRM 1 50 mA Minimum Insulation Breakdown Voltage (Circuit to Case) VISO 2500 VOLTS Typical Thermal Resistance, Junction to Case RqJC 1.2 Maximum Forward Voltage (Per Diode) at 7.5 Amps DC o Maximum Reverse Current at Rated VRM @ TA = 25 C o @TA = 125 C o C/W 3.01 15dbp NOTES: (1) These bridges exhibit the avalanche characteristic at breakdown. If your application requires a specific breakdown voltage range, please contact us. E37 Data Sheet No. BRDB-1500P-2B ABDB-1500P-2B DIOTEC ELECTRONICS CORP. 18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958 15 AMP SILICON BRIDGE RECTIFIERS RATING & CHARACTERISTIC CURVES FOR SERIES DB1500P - DB1510P and SERIES ADB1504P - ADB1508P 18 400 o Peak Forward Surge Current (Amperes) Average Forward Current, Io (Amperes) 60Hz Resistive or Inductive Loads 15 12 9 6 3 0 Bridge Mounted on 5 x 4 x 3" Thick (12.7 x 10.2 x 7.6cm) Finned Al. Plate TJ = 125 C 300 200 100 60 0 50 75 100 10 1 150 100 Number of Cycles at 60 Hz o Case Temperature, C FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT FIGURE 1. FORWARD CURRENT DERATING CURVE 10 1000 O Instantaneous Reverse Current, I (Microamperes) Instantaneous Forward Current (Amperes) TJ = 125 C 100 10 o TJ = 25 C Pulse Width = 300mSec 1%Duty Cycle 1.0 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE E38 1.0 O TJ = 25 C 0.1 .01 0 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS 3.01 15dbp