HAMAMATSU C10439

MODULE
Photodiode module
C10439 series
Integrates a Si photodiode for precision photometry with low-noise amp
C10439 series photodiode modules are high-precision photodetectors that integrate a Si photodiode and a current-to-voltage amplifier. The output
from these photodiode modules is an analog voltage and can be easily checked with a voltmeter, etc. Since their sensitivity is switchable between
two ranges (High/Low), highly accurate output can be obtained by selecting the proper sensitivity range that matches the light level to be
detected. C10439 series is available with three different active areas.
Features
Applications
l Voltage output for easy handling
l Two-range (High/Low) switching function
l Only half size of a business card
l Can be mounted on optical bench rod (M4)
l Choice of active areas
l Precision photometry
l Light source power monitors
l Fluorescence detection of printed matter
l Illuminometers
l Color difference meters
l Refractometer
l Flowmeters, etc.
C10439-01: 2.4 × 2.4 mm
C10439-02: 5.8 × 5.8 mm
C10439-03: 10 × 10 mm
■ Absolute maximum ratings (Ta=25 °C)
Parameter
Supply voltage
Operating temperature *1
Storage temperature *1
*1: No condensation
Symbol
Vcc Max.
Topr
Tstg
Value
±13
0 to +50
-10 to +60
Unit
V
°C
°C
■ Recommended operating range
Parameter
Supply power voltage
Symbol
Vcc
Min.
±5
Typ.
-
Max.
±12
Unit
V
■ Electrical and optical characteristics (Ta=25 °C, Vcc=±12 V, unless otherwise noted)
Parameter
Spectral response range
Peak sensitivity wavelength
Saturation input
optical power
Symbol
λ
λp
Photo sensitivity
S
Frequency bandwidth
(-3 dB)
fc
Conversion impedance
Zt
Maximum output amplitude
VFS
Dark voltage
Time drift (drift over time)
Vd
-
Output noise voltage width
Vn
Condition
High range, λ=λp
Low range, λ=λp
High range, λ=λp
Low range, λ=λp
High range
Low range
High range
Low range
Vcc=±5 to ±12
Output current Io=1 mA
Dark state
Dark state Ta=25 °C *2
Dark state,
within frequency band
Min.
DC
DC
-
Typ.
190 to 1100
960
23
2360
500
5
10
1000
1 × 109
1 × 107
Max.
-
+Vcc - 0.5
+Vcc - 0.2
-
V
-5
-0.5
-
+5
+0.5
mV
mV/day
-
2
5
mVp-p
±2
pF
Ω
mA
Capacitive load
CL
500
Output resistance
Zo
100
Current consumption
Icc
Dark state
*2: Dark voltage variation per day, measured at 25 °C after a 10-minute warm-up after power-on.
Unit
nm
nm
nW
mV/nW
Hz
V/A
1
Photodiode module
■ Block diagram
■ Output voltage vs. input light
RANGE SELECTOR SWITCH
OUTPUT VOLTAGE (V)
+Vcc
I-V
CONVERSION
AMPLIFIER
(Typ. Ta=25 ˚C, Vcc=±12 V, λ=λp)
100
Rf
PD
C10439 series
OUT
10
HIGH RANGE
1
0.1
LOW RANGE
GND
-Vcc
0.01
0.001
0.01
0.1
1
10
100
1000 10000
INPUT LIGHT (nW)
KACCC0364EA
■ Spectral response
(Typ. Ta=25 ˚C)
PHOTO SENSITIVITY (mV/nW)
1000
HIGH RANGE
100
10
LOW RANGE
1
200
400
600
800
1000
1200
WAVELENGTH (nm)
KACCB0153EA
2
KACCB0172EA
Photodiode module
C10439 series
■ Dimensional outlines (unit: mm, torelance: ±0.2 mm unless otherwise noted)
C10439-01
(2 ×) M3 DEPTH 4
59
ACTIVE AREA
2.4 × 2.4
CONNECTOR: HR10A-7R-4P
CONNECTOR: BNC
14.1 * 14.3 * 12.6 *
46
52
44
19
34
HIGH/LOW RANGE
SELECTOR SWITCH
M4 DEPTH 4.5
* ±0.15
KACCA0203EA
C10439-02
(2 ×) M3 DEPTH 4
59
ACTIVE AREA
5.8 × 5.8
CONNECTOR: HR10A-7R-4P
CONNECTOR: BNC
14.1 * 14.3 * 12.6 *
46
52
44
19
34
HIGH/LOW RANGE
SELECTOR SWITCH
M4 DEPTH 4.5
* ±0.15
KACCA0204EA
C10439-03
(2 ×) M3 DEPTH 4
59
ACTIVE AREA
10 × 10
CONNECTOR: HR10A-7R-4P
CONNECTOR: BNC
14.1 * 14.3 * 12.6 *
46
52
44
19
34
M4 DEPTH 4.5
HIGH/LOW RANGE
SELECTOR SWITCH
* ±0.15
KACCA0205EA
3
Photodiode module
C10439 series
■ Connection examples
Connection with DC voltmeter, oscilloscope, etc.
CONNECTION CABLE
FOR PHOTODIODE MODULE *
+V
-V
GND
PHOTODIODE
MODULE
C10439 SERIES
±5 to 12 V POWER SUPPLY
NC
BNC CABLE
Secure with optical bench rod, etc.
VOLTMETER, OSCILLOSCOPE, etc.
* Accessory of Photodiode module
KACCC0365EA
Connection with signal processing unit for photodiode module
SIGNAL PROCESSING UNIT FOR
PHOTODIODE MODULE C10475
AC ADAPTER
(not needed when C10475
operates on battery)
CONNECTION CABLE
FOR PD MODULE
RS-232C
CABLE
BNC CABLE
AC 100 to 240 V
50/60 Hz
PHOTODIODE MODULE
C10439 SERIES
PC
(with supplied software installed)
Secure with optical bench rod, etc.
KACCC0366EA
■ Accessory
· Cable for power supply: length 1 m (no connector on one end)
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions.
Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2008 Hamamatsu Photonics K.K.
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741
Cat. No. KACC1139E02
Feb. 2008 DN
4