CAR2512FP Series 2500 Watt +12V Front End Power Supply Features: ∎ Leading Edge Power Density, 27W/in3 in 1U Form Factor ∎ Works in Parallel with DC Input Models (CAR2412DC) ∎ I2C Serial Bus and PMBus Interface ∎ Up to 91.5% Efficiency (90% at 20% Load) ∎ Active Current Sharing (Single Wire) ∎ Remote On/Off, Remote Sense, Voltage Program Circuits ∎ Microprocessor Based Design Allows for Automatic Fan Speed Control ∎ Front Panel AC Access via IEC-320 Inlet FEATURES High Power Density 27W/in3 Load Sharing & Fault Tolerant Automatic Fan Speed Control High Efficiency under light Loads BENEFITS More system space for application circuits and hardware Excellent reliability in N+1 operation with AC or DC Input Versions Reduces audible noise and increases reliability Supports Demands for Latest Server Farm Trends SPECIFICATIONS Input Voltage Range Input Current Maximum Inrush Current Input Protection Power Factor Efficiency 2500 Watt 12V Front End Power Supply 180-264 VAC, 47-63 Hz, derate for 140-180 VAC Operation 16A @ 180VAC, Full Load (max) 40A max. cold start (per ETS 300 132-1 and Bellcore specifications) One fuse (line) - 20A & 250Vac Type 3AB Axial 0.99 typical complies with IEC555, EN60555-2, EN61000-3-2 Up to 91.5% (90% eff. @ 20% load, 91.5% eff @ 30% load, 90.5% eff @ 50%, 88% @ 100% Load), Operating under 12V output @ 230 VAC (including ORing MOSFETS) 2500W at High Line Operation (180-264 VAC) 10.8V to 13.2Vdc via analog and I2C / PMBus 208 Amps @ 12 VDC 3.3VSB @ 1A, reference to Vout Return (optional 5VSB) ±2% of Vnom for any combination of line, load and temperature ±1% (pk-pk) @ 20MHz with 0.1μF ceramic and 10μF electrolytic caps at the output 5% max deviation, recovery time 300μs @ 50% load step and di/dt < 1A/μs 400khz typical or optimized for efficiency gains 12ms at full load measured down to 10.8V (with 230Vac). An early warning signal is provided 2ms prior to loss of output power. Ride thru is 8.3ms typically TTL Compatible input, ON if >3V or open, OFF if <1V” 110-130% of Iout nominal Self protected with auto recovery Trip level: ≥14.8Vdc ± 1V, Reset condition by recycling the input or applying Remote On/Off -10°C to +70°C Non latching; protection active at 110°C internal temperature, restart at 95°C (typical) FCC-B & EN55022-B with specified filter or at rack-level, GR-1089-CORE Two LED’s, 1st Led (Green = AC OK), 2nd LED (Green = DC OK / Red = Fault) Voltage Programming (V Prog), Load sharing (I Share), Remote ON/OFF, Current Monitor (I Monitor), Over temperature (Temp Warning), Fault, PS Present, Module Enable, AC OK, DC OK I2C and PMBus Telcordia NEBS GR-63-CORE Level III 14.88” x 4.00” x 1.65” / 378mm x 102mm x 41.9mm 4.73lbs / 2.15kg IEC/UL/CSA/EN60950-1, CE Mark (LVD), TUV 5VSB Output Output Power Output Voltage Range Output Current Standby Bias Voltage Voltage Regulation Ouput Ripple & Noise Transient Response Switching Frequency Hold-Up Time Remote On/Off Current Limit Protection Short Circuit Protection Over Voltage Protection Operating Temperature Over Temperature Protection EMI LED Indicators Analog Status & Control Digital Status & Control Shock & Vibration Dimensions Weight Safety Approvals Options KEY MARKET SEGMENTS & APPLICATIONS ∎ Distributed Power ∎ Storage Equipment ∎ Mid-High End Servers ∎ High-End Routers & Switchgear rev 100506 www.lineagepower.com/oem Lineage Power Lineage Power Lineage Power (China) 3000 Skyline Dr. Mesquite, TX 75149 Phone: (972) 284-2000 2841 Dow Avenue Tustin, CA 92780 USA Phone: (714) 544-6665 1353 Chenqiao Road, Shanghai Sengpu Industrial Park Shanghai, 201401 China Phone: 021 6710 8910 CAR2512FP Series 2500 Watt +12V Front End Power Supply OUTLINE DRAWING All Dimensions in Inches (mm) Tolerance: .XX = ± .02 in (.50 mm) .XXX = ± .010 in (.254 mm) EFFICIENCY CURVE: CONNECTOR DRAWING: 95% 93% Efficiency % 1 91.5% 91% 2 3 4 5 6 D 90.5% 90% C 88% 89% P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 B 87% A 85% 83% 81% DC Output : Tyco P/N 6600122-7 (Rear side) / Mating Connector: Tyco P/N 6450171-5 79% 10% 20% 40% 50% 60% 80% 100% % of Load @ 230Vac PART NUMBER DEFINITION GUIDE: PIN OUT INFORMATION A1 A2 A3 A4 A5 A6 B1 B2 B3 B4 B5 B6 CAR 25 12 F P x x xx -1A Series 25=2500W Output Current 12=12V Output Voltage Example: F=Front End Type P=Positive Polarity Rev. YO=5 of 6 Compliant ZO=6 of 6 Compliant RoHS Blank = 3.3VSB 5 = 5VSB Standby Voltage B=Bezel Option Blank=None Options CAR2512FPB5Z0-1A 2500W / 12Vout / Bezel / 5VSB / 6 of 6 RoHS VSB [3.3] PS Present Signal Return Write Protect Remote Sense (+) Remote Sense (-) Fault I Monitor Module Enable VSB [3.3] Return SDA SCL C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 I Share N/C Temp OK I2C Address (A0) I2C Address (A1) I2C Address (A2) V Prog OVP Test Point Remote ON/OFF DC OK AC OK Interrupt rev 100506 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 Output Return Output Returnt Output Return Output Returnt Output Return Output Return +Vout +Vout +Vout +Vout +Vout +Vout www.lineagepower.com/oem Lineage Power Lineage Power Lineage Power (China) 3000 Skyline Dr. Mesquite, TX 75149 Phone: (972) 284-2000 2841 Dow Avenue Tustin, CA 92780 USA Phone: (714) 544-6665 1353 Chenqiao Road, Shanghai Sengpu Industrial Park Shanghai, 201401 China Phone: 021 6710 8910