CATALYST CAT1232LPL-GT3

CAT1232LP/CAT1832
5V and 3.3V Supply Monitor, Watchdog Timer,
Manual Reset, with Active High & Low Resets
FEATURES
DESCRIPTION
■ Selectable reset voltage tolerance
The CAT1232LP and CAT1832 microprocessor
supervisors can halt and restart a “hung-up” or “stalled”
microprocessor, restart a microprocessor after a power
failure, and debounce a manual/push-button microprocessor reset switch. The devices are drop in
replacements for the Maxim/Dallas Semiconductor
DS1232LP and DS1832 supervisors
— CAT1232LP for 5V supply
— CAT1832 for 3.3V supply
■ Selectable watchdog period:
150ms, 600ms or 1.2 sec
■ Two reset outputs
Precision reference and comparator circuits monitor the
5V or 3.3V system power supply voltage, VCC. During
power-up or when the power supply falls outside
selectable tolerance limits, both the RESET and RESET
become active. After the power supply voltage rises
above the RESET threshold voltage, the reset signals
remain active for a minimum of 250ms, allowing the
power supply and system processor to stabilize. The
trip-point tolerance input, TOL, selects the trip level
tolerance to be either 5% or 10% for the CAT1232LP 5V
supply and 10% or 20% for the CAT1832 3.3V supply.
— Active high, push-pull reset output
— Active low, open-drain reset output
(CAT1232LP)
— Active low, push-pull reset output (CAT1832)
■ Debounced manual push-button reset
■ Compact SOIC and MSOP packages
APPLICATIONS
■ Microprocessor Systems
Each device has a push-pull, active HIGH reset output.
The CAT1232LP also has an open drain, active LOW
reset output while the CAT1832 also has a push-pull,
active LOW reset output.
■ Portable Equipment
■ Controllers
■ Single Board Computers
A debounced manual reset input activates the reset
outputs and holds them active for a minimum period of
250ms after being released.
■ Instrumentations
■ Telecommunications
Also included is a watchdog timer to reset a
microprocessor that has stopped due to a software or
hardware failure. Three watchdog time-out periods are
selectable: 150ms, 600ms and 1.2sec. If the ST input is
not strobed low before the watchdog time out period
expires, the reset signals become active for a minimum
of 250ms.
For Ordering Information details, see page 11.
FUNCTIONAL DIAGRAM
VCC
TOL
Tolerance Selection
+
Reference
–
(CAT1232LP)
RESET
VCC
40kΩ
RESET
PBRST
Push Button Debounce
TD
Watchdog Timebase Selection
ST
Watchdog Transition Detector
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Reset &
Watchdog Timer
1
RESET
(CAT1832)
Doc. No. 25089, Rev. 0C
CAT1232LP/CAT1832
PIN CONFIGURATION
16-Lead SOIC
8-Lead SOIC/MSOP/DIP
PBRST 1
8 VCC
TD 2
7 ST
NC
1
16 NC
PBRST
2
15 VCC
TOL 3
6 RESET
NC
3
14 NC
GND 4
5 RESET
TD
4
13 ST
NC
5
12 NC
TOL
6
11 RESET
NC
7
10 NC
GND
8
9 RESET
PIN DESCRIPTION
Pin Number
Pin Number
8-Lead Package 16-Lead Package
1
2
2
4
Name
PBRST
TD
3
6
TOL
4
5
8
9
GND
RESET
6
7
8
11
13
15
1, 3. 5, 7, 10, 12,
14, 16
RESET
ST
VCC
NC
Doc. No. 25089, Rev. 0C
Function
Debounced manual pushbutton reset input
Watchdog typical time delay selection:
a) tTD = 150ms for TD = GND
b) tTD = 600ms for TD = Open
c) tTD = 1200ms for TD = VCC
CAT1232LP TOL selects 5% (TOL = GND) or 10% (TOL = VCC) trip
point tolerance. CAT1832 TOL selects 10% (TOL = GND) or 20% TOL =
VCC) trip point tolerance.
Ground
Active HIGH reset output. RESET is active
1. If VCC falls below the reset voltage trip point
2. If PBRST is low
3. If ST is not strobed low before the timeout period set by TD expires.
4. During power-up.
Active LOW reset output. (See RESET)
Strobe Input
Power Supply
No internal connection
2
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT1232LP/CAT1832
ABSOLUTE MAXIMUM RATINGS*
Voltage on VCC ....................................... -0.5V to 7.0V
Maximum Junction Temperature ...................... 125°C
Voltage on ST and TD ................. -0.5V to VCC + 0.5V
Storage Temperature Range ............ -65°C to +150°C
Voltage on PBRST, RESET
and RESET ............................ -0.5V to VCC + 0.5V
Lead Soldering Temperature (10 sec) .............. 300°C
Operating Temperature Range ........... -40°C to +85°C
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, 1.0V ≤ VCC ≤ 5.5V and over the operating temperature range of -40°C to +85°C. All
voltages are referenced to ground.
Symbol Parameter
VCC
Conditions
Min
Supply Voltage
ICC1
Supply Current
VIH
ST and PBRST Input High Level
VIL
ST and PBRST Input Low Level
Typ
1.0
Max
Units
5.5
V
VCC = 5.5V, CAT1232LP
35
50
VCC = 3.6V, CAT1832
20
35
(5)
2
(6)
VCC + 0.3V
VCC - 0.4V
VCC = 5.5V, CAT1232LP
– 0.3
µA
V
0.8
V
VCC = 3.6V, CAT1832
0.5
VCCTP
VCC Trip Point (TOL = GND)
CAT1232LP
4.50
4.62
4.74
V
VCCTP
VCC Trip Point (TOL = VCC)
CAT1232LP
4.25
4.37
4.49
V
VCCTP
VCC Trip Point (TOL = GND)
CAT1832
2.80
2.88
2.97
V
VCCTP
VCC Trip Point (TOL = VCC)
CAT1832
2.47
2.55
2.64
V
tTD
tTD
tTD
Watchdog Time-Out Period
Watchdog Time-Out Period
Watchdog Time-Out Period
TD = GND
TD = VCC
TD floating
62.5
500
250
150
1200
600
250
2000
1000
ms
ms
ms
VOH
Output Voltage
I = – 500µA(3)
VCC - 0.5V
VCC - 0.1V
V
– 350
µA
IOH
Output Current
IOL
Output Current
Output = 0.4V,
IIL
RPU
Input Leakage
Internal Pull-Up Resistor
(1)
CIN
COUT
Input Capacitance
5
pF
Output Capacitance
7
pF
tRST
Reset Active Time
tPDLY
tRPU
tR
– 1.0
32
mA
µA
kΩ
PBRST Manual Reset
Minimum Low Time
tF
10
1.0
55
tPB
tST
tRPD
Output =
2.4V(2)
(1)
PBRST = VIL
20
250
ST Pulse Width
VCC Fail Detect to
RESET or RESET
VCC Slew Rate
PBRST Stable LOW to
RESET and RESET Active
VCC Detect to RESET or
RESET Inactive
(4)
VCC Slew Rate
4.25V to 4.75V
ms
600
1000
ms
5
8
ns
µs
20
µs
ms
1000
ms
20
20
tRISE = 5µs
250
0
Notes:
(1) PBRST is internally pulled HIGH to VCC through a nominal 40kΩ
resistor (RPU).
(2) RESET is an open drain output on the CAT1232LP.
(3) RESET remains within 0.5V of VCC on power-down until VCC falls
below 2V. RESET remains within 0.5V of ground on power-down
until VCC falls below 2.0V.
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
40
600
ns
(4) Must not exceed the minimum watchdog time-out period (tTD).
The watchdog circuit cannot be disabled. To avoid a reset, ST
must be strobed.
(5) Measured with VCC ≥ 2.7V.
(6) Measured with VCC < 2.7V.
3
Doc. No. 25089, Rev. 0C
CAT1232LP/CAT1832
TYPICAL CHARACTERISTICS
For the CAT1232LP, VCC = 5V and TAMB = 25°C unless otherwise stated.
Threshold Voltage vs. Temperature (5% TOL)
4.450
THRESHOLD VOLTAGE (V)
THRESHOLD VOLTAGE (V)
Threshold Voltage vs. Temperature (10% TOL)
4.445
TOL = Vcc (10%)
4.440
4.435
0
50
4.625
TOL = GND (5%)
4.620
4.615
4.610
-50
4.430
-50
4.630
100
Supply Current vs. Temperature
800
RESET ACTIVE TIME (ms)
SUPPLY CURRENT (µA)
Vcc = 5.5V
Vcc = 4.5V
20
10
0
50
100
TEMPERATURE (°C)
TD = open
700
600
500
Vcc = 5.5V
Vcc = 4.5V
400
300
-50
0
50
100
TEMPERATURE (°C)
Reset Active Time Waveform
Doc. No. 25089, Rev. 0C
100
Reset Active Time vs. Temperature
40
0
-50
50
TEMPERATURE (°C)
TEMPERATURE (°C)
30
0
Transient Response
4
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT1232LP/CAT1832
APPLICATION INFORMATION
Connecting TOL to VCC makes the VCC trip threshold
4.37V for the CAT1232LP and 2.55V for the CAT1832.
SUPPLY VOLTAGE MONITOR
After VCC has risen above the trip point set by TOL,
RESET and RESET remain active for a minimum time
period of 250ms.
Reset Signal Polarity and Output Stage Structure
RESET is an active LOW signal. It is developed with an
open drain driver in the CAT1232LP. A pull-up resistor
is required, typical values are 10kΩ to 50kΩ. The
CAT1832 uses a CMOS push-pull output stage for the
RESET.
On power-down, once VCC falls below the reset threshold
the RESET outputs will remain active and are guaranteed
valid down to a VCC level of 1.0V.
RESET is an active High signal developed by a CMOS
push-pull output stage and is the logical opposite to
RESET.
Trip Point Tolerance Selection
The TOL input is used to select the VCC trip point
threshold. This selection is made connecting the TOL
input to ground or VCC. Connecting TOL to Ground
makes the VCC trip threshold 4.62V for the CAT1232LP
and 2.88V for the CAT1832.
Tolerance
Select
Voltage
Trip Point
Tolerance
MIN
NOMINAL
MAX
CAT1232LP
TOL = VCC
10 %
4.25
4.37
4.49
CAT1232LP
TOL = GND
5%
4.50
4.62
4.74
CAT1832
TOL = VCC
20 %
2.47
2.55
2.64
CAT1832
TOL = GND
10 %
2.80
2.88
2.97
tF
tR
VCCTP(MIN)
VCC
VCCTP(MAX)
VCCTP
VCC
Trip Point Voltage (V)
VCCTP(MAX)
VCCTP
VCCTP(MIN)
tRPU
RESET
VOL
tRPD
RESET
VOH
RESET
RESET
VOH
VOL
Figure 1. Timing Diagram: Power Up
Figure 2. Timing Diagram: Power Down
Manual Reset Operation
Push-button input, PBRST, allows the user to issue
reset signals. The pushbutton input is debounced and is
pulled high through an internal 40kΩ resistor.
No external pull-up resistor is required, since PBRST is
pulled high by an internal 40kΩ resistor.
PBRST can be driven from a TTL or CMOS logic line or
short-ed to ground with a mechanical switch.
When PBRST is held low for the minimum time of 20 ms,
both resets become active and remain active for a
minimum time period of 250ms after PBRST returns
high.
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. 25089, Rev. 0C
CAT1232LP/CAT1832
WATCHDOG TIMER AND ST INPUT
A watchdog timer stops and restarts a microprocessor
that has stopped proper operation or become “hung”.
The watchdog performs this function by monitoring the
ST input. After the reset outputs go inactive the ST input
must be strobed with a high-to-low signal transition prior
to the minimum watchdog timeout period. However if the
ST input is not strobed with a high-to-low signal transition prior to a watchdog timeout the reset outputs will
become active for TRST reseting and restarting the
microprocessor. Once the resets return to the inactive
state the watchdog timer restarts the process.
MIN
NOMINAL
MAX
GND
62.5
150
250
Floating
250
600
1000
VCC
500
1200
2000
3.3V
CAT1832
1
The TD input allows the user to select from three
predetermined watchdog timeout periods. Always use
the minimum timeout period to determine the required
frequency of ST high-to-low transitions and the maximum to determine the time prior to the reset outputs
becoming active. ST pulse widths must be 20ns or
greater.
2
3
4
The watchdog timer cannot be disabled. It must be
strobed with a high-to-low signal transition to avoid a
watchdog timeout and subsequent reset.
2
3
4
PBRST
TD
TOL
GND
VCC
ST
RESET
RESET
PBRST
TD
VCC
ST
TOL
RESET
GND
RESET
8
7
I/O
µP
6
5
RESET
Figure 4. CAT1832 Application Circuit:
Pushbutton Reset
5V
CAT1232LP
1
Watchdog Time-out Period (ms)
TD Voltage
Level
8
MREQ
7
10k
Address
Bus
µP
6
RESET
Decoder
5
Figure 5. CAT1232LP Application Circuit: Watchdog Timer
tPB
PBRST
tPDLY
VIH
Valid
Strobe
ST
VIL
RESET
tRST
RESET
VOH
VOL
tTD
(Min)
tTD
(Min)
RESET
Note: ST is ignored whenever a reset is active.
Figure 6. Timing Diagram: Pushbutton Reset
Doc. No. 25089, Rev. 0C
Invalid
Strobe
tST
tRST
RESET
Valid
Strobe
Figure 7. Timing Diagram: Strobe Input
6
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT1232LP/CAT1832
PACKAGE DRAWING
16-LEAD WIDE BODY SOIC (300mil)
E1
E
h x 45
D
C
A
θ1
e
A1
L
b
SYMBOL
MIN
A1
A
b
C
D
E
E1
e
h
L
θ1
0.10
2.36
0.33
0.23
10.10
10.00
7.40
0.25
0.40
0°
NOM
2.49
0.41
0.28
10.31
10.31
7.50
1.27 BSC
0.81
MAX
0.30
2.65
0.51
0.32
10.50
10.65
7.60
0.75
1.27
8°
16-Lead_SOIC_(300mil).eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters.
2. Complies with JEDEC specification MS-013.
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. 25089, Rev. 0C
CAT1232LP/CAT1832
PACKAGE DRAWING
8-LEAD DIP (300mil)
E1
E
D
A2
A
A1
L
e
eB
b2
b
SYMBOL
A
A1
A2
b
b2
D
E
E1
e
eB
L
MIN
NOM
MAX
4.57
0.38
3.05
0.36
1.14
9.02
7.62
6.17
7.87
2.79
0.46
7.87
6.35
2.54 BSC
3.81
0.56
1.52
10.16
8.26
7.49
9.65
3.81
24C16_8-LEAD_DIP_(300P).eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters.
2. Complies with JEDEC Standard MS001.
3. Dimensioning and tolerancing per ANSI Y14.5M-1982
Doc. No. 25089, Rev. 0C
8
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT1232LP/CAT1832
PACKAGE DRAWING
8-LEAD MSOP
E1
E
e
D
A2
b
SYMBOL
MIN
L
A1
NOM
A
MAX
1.10
A1
0.00
0.15
A2
0.75
0.95
b
0.22
D
2.90
0.38
3.00
3.10
E
4.80
4.90
5.00
E1
2.90
3.00
3.10
e
L
GAUGE
PLANE
A
0.65 BSC
0.40
0.8
0°
8°
8-lead_MSOP3.eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters. Angles in degrees.
2. Complies with JEDEC Specification MO-187.
3. Stand off height/coplanarity are considered as special characteristics.
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. 25089, Rev. 0C
CAT1232LP/CAT1832
PACKAGE MECHANICAL
8-LEAD Narrow Body SOIC (150mil)
E1
E
h x 45
D
C
A
θ1
e
A1
L
b
SYMBOL
MIN
A1
A
b
C
D
E
E1
e
h
L
θ1
0.10
1.35
0.33
0.19
4.80
5.80
3.80
NOM
MAX
0.25
1.75
0.51
0.25
5.00
6.20
4.00
1.27 BSC
0.25
0.40
0°
0.50
1.27
8°
24C16_8-LEAD_SOIC.eps
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
Notes:
1. All dimensions are in millimeters. Angles in degrees.
2. Complies with JEDEC Specification MS-012.
Doc. No. 25089, Rev. 0C
10
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT1232LP/CAT1832
SAMPLE OF ORDERING INFORMATION
Prefix
Device #
CAT
Suffix
1232LP
Company ID
V
–
G
Product Number
1232 LP
1832
L:
V:
W:
Z:
T3
T: Tape & Reel
2: 2000/Reel
3: 3000/Reel
Package
PDIP (Lead-free, Halogen-free)
SOIC 8-Lead (Lead-free, Halogen-free)
SOIC 16-Lead (Lead-free, Halogen-free)
MSOP (Lead-free, Halogen-free)
Lead Finish
Blank: Matte-Tin
G: NiPdAu
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard lead finish is NiPdAu.
(3) The device used in the above example is a CAT1232LPV-GT3 (SOIC, NiPdAu, Tape & Reel).
(4) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office.
Green NiPdAu Lead Finish
Ordering Part Number
Package
Parts per Tube
Parts Per Reel
Reel Size (inch)
CAT1232LPL-G
8-lead, DIP
50
—
—
CAT1232LPV-GT3
8-lead, SOIC
—
3,000
13
CAT1232LPZ-GT3
MSOP
—
3,000
13
CAT1232LPW-GT2
16-lead, SOIC
—
2,000
13
CAT1832L-G
8-lead, DIP
50
—
—
CAT1832V-GT3
8-lead, SOIC
—
3,000
13
CAT1832Z-GT3
MSOP
—
3,000
13
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. 25089, Rev. 0C
REVISION HISTORY
Date
Revision Comments
06/13/2005
00
Initial Issue
07/26/2005
0A
Update Electrical Characteristics
Add Typical Characteristics
03/27/2006
0B
Update Document Title
Update Ordering Information
08/21/2006
0C
Add Ordering Information detail to page 1
Update Sample of Ordering Information
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
DPP ™
AE2 ™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a
situation where personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate
typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
2975 Stender Way
Santa Clara, CA 95054
Phone: 408.542.1000
Fax: 408.542.1200
www.catsemi.com
Publication #:
Revison:
Issue date:
25089
0C
08/21/06